NAPOLEON NEFB36H-BS Manuel utilisateur

Marque: NAPOLEON

Modèle: NEFB36H-BS

Taper: Manuel utilisateur

FRENCH PG. 27

W415-1980 / C / 03.25.22

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleon.com • [email protected]

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

CSA 22.2 NO. 46 / UL 1278

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

SAFETY INFORMATION

- Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the vicinity of

this or any other appliance.

FIRE OR EXPLOSION HAZARD

If the information in these instructions are

not followed exactly, a ﬁ re or explosion may

result causing property damage, personal

injury, or loss of life.

WARNING

ENGLISH

$10.00

This appliance has a remote that requires button

batteries that are hazardous to young children.

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

CSA C22.2 NO. 46 / UL 2021

W415-1980 / C / 03.25.22

safety information

• If equipped with a heater, this appliance can be hot when operated and can cause severe

burns if contacted.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate

appliance according to operating instructions could cause ﬁ re or injury.

• Do not install damaged, incomplete or substitute components.

• Do not burn wood or other materials in this appliance.

• All electric appliances have hot and arcing or sparking parts inside. Do not use it in areas where a gas

line, paint or ﬂ ammable liquids are present.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• It is imperative that the control compartments, circulating blower and its passageway in the appliance

are kept clean. The appliance should be inspected before use and at least annually by a qualiﬁ ed service

person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material,

etc. The appliance area must be kept clear and free from combustible materials, gasoline and other

ﬂ ammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician to

inspect the appliance and to replace any part of the control system which has been under water.

• If equipped with a glass door, do not operate the appliance with the glass door removed, cracked or

broken. Replacement of the glass should be done by a licensed or qualiﬁ ed service person. Do not strike

or slam shut the appliance glass door.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Servicing should be done only while the appliance is disconnected from the power supply circuit.

• Always unplug appliance when not in use.

• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been

dropped or damaged in any manner. Return appliance to authorized service facility for examination,

electrical or mechanical adjustment, or repair.

• Do not use outdoors.

• When installing this appliance in a room where water is present, the installation must comply with codes

recognizing the increased hazard of electrical shock and electrocution.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord

away from trafﬁ c area and where it will not be tripped over.

• Connect to properly grounded outlets only.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an

electric shock or ﬁ re, or damage the appliance.

• It is normal for your electric appliance to produce noise, especially when installed in a quiet space such

as a bedroom.

Insert appropriate “Bathroom Warning (Electric)” (see 3-Warnings template folder).

W415-1980 / C / 03.25.22 3

safety information

• To prevent a possible ﬁ re, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like

a carpet, where openings may become blocked.

• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or relocatable

power tap (outlet/power strip).

• These appliances are tested and listed for use only with the optional accessories listed in these instructions.

Use of optional accessories not speciﬁ cally tested for this appliance could void the warranty and/or result in

a safety hazard.

For appliances equipped with a heater:

• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before

servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is

recommended if there are at risk individuals in the house. To restrict access to an appliance or stove, install

an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and

away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and

draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is off, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from

hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.

Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or

damage to decorations, a TV or other electronic components.

W415-1980 / C / 03.25.22

table of contents

1.0 general information 5

1.1 dimensions 5

1.2 hardware list 5

1.3 listing approvals 6

1.4 general instructions 6

1.5 unpacking and testing appliance 6

1.6 rating plate information 7

1.7 label location 7

2.0 locating appliance 8

2.1 grounding appliance 8

3.0 installation and finishing 9

3.1 minimum clearance to combustibles 9

3.2 minimum mantel clearances 9

3.3 rough framing 10

3.4 appliance installation and ﬁ nishing 11

4.0 electrical information 15

4.1 120V cord plug installation 15

4.2 wiring diagram 15

4.3 hard-wiring installation 16

4.3.1 120V hard-wiring installation 16

4.3.2 240V hard-wiring installation 16

5.0 operating instructions 17

5.1 operating control panel 17

5.2 operating remote control 18

5.3 remote battery installation 19

6.0 maintenance 19

7.0 replacement parts 20

7.1 overview 21

8.0 troubleshooting 22

9.0 warranty 24

10.0 notes 25

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves

the right to change or modify any information within this manual at any time without notice. Changes, other than

editorial, are denoted by a vertical line in the margin.

note:

W415-1980 / C / 03.25.22 5

dimensions

1.0 general information

1.1 dimensions

1.2 hardware list

Ref. Description Quantity

A Wood Screws 4

B Strain Relief 1

C Junction Box Cover Plate 1

D Wire Nut 1

FRONT VIEW SIDE VIEW

TOP VIEW

W415-1980 / C / 03.25.22

general information

As with most electronic devices, your new electric appliance has been designed to operate at temperatures

between 5°C (41°F) and 35° C (95°F). During the colder winter months, allow the appliance to reach room

temperature before turning it on.

Carefully remove the appliance from the box. Prior to installing the appliance, remove all packaging material and

test to make sure the appliance operates properly by plugging the power supply cord into a conveniently located

120V, 15 Amp minimum grounded outlet.

This appliance has been tested in accordance with the CSA Standards for ﬁ xed and location-dedicated electric

room appliances in the United States and Canada. If you need assistance during installation, please contact your

local dealer. Model No. NEFB36H-BS

Description 36" Electric Appliance

Voltage 120V / 240V

Watts 1500 / 3000W

Amps Dedicated 15 AMP Grounded Circuit

Appliance Width 36 1/8" (918mm)

Appliance Height 31 7/8" (810mm)

Appliance Depth 11 1/4" (286mm)

Net Weight 66.1lbs (30.0kg)

Gross Weight 74.9lbs (34.0kg)

This appliance must be electrically wired and

grounded in accordance with local codes or,

in the absence of local codes, with the latest

edition of the National Electrical Code ANSI/

NFPA 70 in the United States or the Canadian

Electrical Code CSA C22.1 in Canada.

note:

1.3 listing approvals

1.4 general instructions

• Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the outlet

are on.

• The appliance may emit a slight, harmless odour when ﬁ rst used. This odour is normal and it is caused by

the initial heating of internal appliance elements and will not occur again.

•

If your appliance does not emit heat when called for, consult the “operation” section of this manual for further

information.

• Use with a CSA or UL certiﬁ ed surge protector.

• Do not route the power cord directly underneath the appliance.

This electric appliance meets the construction and safety standards of H.U.D. for application in manufactured

homes when installed according to these instructions.

1.5 unpacking and testing appliance

The appliance is factory wired for 120

volt power supply. If 240 volt operation

is required, see "electrical information"

section.

note: Manual

(packaged on

top of appliance)

Outer Box

Brick Panels

(packaged at back

of appliance)

Remote &

Hardware Kit

(packaged on bottom

of appliance)

Exact packaging location may vary.

Some packaging has been hidden for

clarity.

W415-1980 / C / 03.25.22 7

general information

1.6 rating plate information

For rating plate location, see “label location” section.

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

The rating plate must remain with the appliance at all times. It must not be removed.

note:

1.7 label location

Ref. Part Number Label Description

A W385-2210 "Do Not Cover"

B N/A Model & Serial Number

C W385-2610 Wiring Diagram

D W385-2368 Rating Plate

E W385-2167 "Caution"

F W385-2163 "Warning"

G W385-2371 120V Hard-Wiring Diagram

H W385-2372 240V Hard-Wiring Diagram

I W385-1943 "Warning"

W415-1980 / C / 03.25.22

2.0 locating appliance

2.1 grounding appliance

• Due to high temperatures, this electric appliance should be located out of trafﬁ c. Keep combustible materials

such as furniture, pillows, bedding, papers, clothes and curtains at least 36” (91.4cm) from the front of the

appliance.

• Never locate this electric appliance where it may fall into a bathtub or other water container.

• Wear safety gloves and safety glasses for protection during installation and maintenance.

• To prevent contact with sagging or loose insulation, the electric appliance must not be installed against vapor

barrier or exposed insulation. Localized overheating could occur and a ﬁ re could result.

• Do not expose the electric appliance to the elements (such as rain, etc.).

!WARNING

This appliance is for use on 120 volts and 240 volts. The cord has a plug as shown in (A). An adapter as shown in

The green grounding plug extending from the adapter must be connected to a permanent ground such as a

properly grounded outlet box. The adapter should not be used if a three-slot grounded receptable is available.

To disconnect the appliance, turn controls to off, then remove plug from outlet.

note:

This appliance must be connected to a dedicated 15 amp circuit. The use of an extension cord is NOT

permitted.

W415-1980 / C / 03.25.22 9

3.0 installation and ﬁ nishing

Your NEFB36H-BS is a recessed appliance. Select a suitable location that is not susceptible to moisture and is

away from drapes, furniture and high trafﬁ c areas.

3.1 minimum clearance to combustibles

Measurements are taken from the glass front.

Bottom 0" Top 0" to mantel

Sides 0" Top 0" to ceiling

Back 0"

3.2 minimum mantel clearances

• Risk of ﬁ re! The power cord must not be pinched against a sharp edge. Secure cord to avoid tripping or

snagging to reduce the risk of ﬁ re, electric shock, or personal injury. Do not run cord under carpeting. Do not

cover cord with throw rugs, runners, or similar items. Arrange cord away from trafﬁ c areas and where it will not

be tripped over.

• Risk of ﬁ re! To prevent a possible ﬁ re, do not block air intake or exhaust in any manner. Do not use on soft

surfaces where openings may become blocked.

• Risk of ﬁ re! Do not blow or place insulation against the appliance.

• This electric appliance is tested and listed for use only with the approved optional accessories. Use of optional

accessories not speciﬁ cally tested for this electric appliance could void the warranty and/or result in a safety

hazard.

• If the information in these instructions is not followed exactly, a ﬁ re or explosion may result causing property

damage, personal injury, or death. Do not store or use gasoline or other ﬂ ammable vapors in the vicinity of this

or any other appliance.

• This appliance is heavy. It is highly recommended that two people install this appliance.

• If your appliance is equipped with a heater, ensure the heater vents cannot, in any way, be covered as it may

create a ﬁ re hazard.

• Do not run the power cord horizontally, directly below the appliance.

Follow all national and local electrical codes.

note:

The power switch is located on the upper right hand side of the appliance. Ensure to maintain access to this

switch at all times.

note:

• When using paint or lacquer to ﬁ nish the mantel, the

paint or lacquer must be heat resistant to prevent

discolouration.

!WARNING

W415-1980 / C / 03.25.22

installation and ﬁ nishing

3.3 rough framing

• Select a location that is not prone to moisture and is located at least 36" (91.4cm) away from combustible

materials such as curtains, drapes, furniture, bedding, paper, etc.

!WARNING

Once the rough framing and the ﬁ nishing materials have been prepared and the power has been routed to the

right side of the recess, the appliance may be installed.

note:

The electrical connection must be made prior to placing the appliance into position (see "electrical information"

section).

Have two people lift the appliance into position.

In order to avoid the possibility to exposed insulation or vapour barrier coming in contact with the appliance

body, it is recommended that the walls of the appliance enclosure be "ﬁ nished" (i.e. drywall / sheet rock, etc.)

as you would ﬁ nish any other outside wall of a home. This will ensure that clearance to combustibles is main-

tained within the enclosure.

It is recommended to complete ﬁ nishing of the wall before fully securing the appliance.

Rough Framing Rough Framing in a Corner

W415-1980 / C / 03.25.22 11

installation and ﬁ nishing

3.4 appliance installation and ﬁ nishing

1. Remove the front decorative cover held in place by 2 magnets (Fig. 3-1).

2. With one hand on the glass door to prevent it from falling, remove the 2 screws holding the glass door in place

(Fig. 3-2).

3. Carefully lift the glass door out of the 2 slots in the bottom of the ﬁ rebox (Fig. 3-3). Set the glass door on a

soft, non-abrasive surface.

4. Remove the 4 screws holding the log set in place (Fig. 3-4) then carefully remove the log set. Set the log set

aside (Fig. 3-5) and discard the 4 screws.

Fig. 3-1 Fig. 3-2

Fig. 3-4

Fig. 3-3

Slot

Decorative

Cover

Fig. 3-5

Remove screws

from top holes.

W415-1980 / C / 03.25.22

installation and ﬁ nishing

It is recommended to complete ﬁ nishing of the wall before fully securing the appliance (Fig. 3-6).

note:

5. Complete hard-wiring (see "electrical information" section).

6. Carefully lift the appliance into the rough-in framing (Fig. 3-7).

Fig. 3-8

Framing

hidden for

clarity.

Bend tabs as

necessary.

A x 4

7. Secure the appliance to the rough-in framing by installing 4 screws (supplied) through one of the three holes

of the mounting tabs from the inside of the appliance (Fig. 3-8).

Fig. 3-6 Fig. 3-7

W415-1980 / C / 03.25.22 13

installation and ﬁ nishing

Fig. 3-10

Fig. 3-11

Fig. 3-9

Repeat on

opposite

side.

Bottom

retainer

Side

retainer

Repeat on

opposite

side.

8. Remove the 4 screws holding the back retainers in place (Fig. 3-9). Set the screws and retainers aside (Fig.

3-10).

Fig. 3-12

Repeat on

opposite

side.

Fig. 3-13

9. Place the brick panels into the bottom retainers and behind the side retainers (Fig. 3-11).

10. Re-install the 2 back retainers by re-installing the 4 screws previously removed in step 8 (Fig. 3-12 and 3-13).

W415-1980 / C / 03.25.22

installation and ﬁ nishing

Fig. 3-14 Fig. 3-15

Framing

hidden for

clarity.

Fig. 3-17

Framing

hidden for

clarity.

Framing

hidden for

clarity.

Slot

Fig. 3-16

11. Re-install the log set without reinstalling the 4 screws removed in step 4 (Fig. 3-14).

12. Re-install the glass door (Fig. 3-15 and 3-16).

13. Re-install the front decorative cover held in place by 2 magnets (Fig. 3-17).

W415-1980 / C / 03.25.22 15

4.0 electrical information

• Turn off the appliance completely and let cool before servicing. Only a qualiﬁ ed service person should service

and repair this electric appliance.

!WARNING

This appliance must be connected to a dedicated 15 amp circuit. The use of an extension cord is NOT

permitted.

note:

4.1 120V cord plug installation

4.2 wiring diagram

The factory default setting is 120 volt cord plug installation conﬁ guration. Simply plug the appliance to a grounded

120V, 15 amp outlet box.

W415-1980 / C / 03.25.22

electrical information

• Turn off the appliance completely and let cool before servicing. Only a qualiﬁ ed service person should service

and repair this electric appliance.

!WARNING

HARD-WIRING CONNECTION

If it is necessary to hard-wire this appliance, a qualiﬁ ed electrician must remove the cord connection, and wire the

appliance directly to the household wiring. The wire and power supply breaker must be rated for 120V, minimum

15 amps.

This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local

codes, with the latest edition of the National Electrical Code ANSI/NFPA 70 in the United States or the Canadian

Electrical Code CSA C22.1 in Canada.

4.3 hard-wiring installation

4.3.1 120V hard-wiring installation

1. Remove the 4 screws securing the cord and cover plate to the side of the ﬁ rebox.

2. Unscrew the wire nuts securing the power supply cord.

3. Install the new strain relief (supplied) (Fig. 4-1) into the new cover plate (supplied) and feed the 14/2

conductor wire through the strain relief.

4. Connect the ground/bond wires together.

5. Connect L1 to L1 of the appliance.

6. Connect the supply N wire to the two N wires in the junction box. Do not connect the L2 wire.

7. With wires secured, carefully feed the wires into the ﬁ rebox and re-secure the cover plate.

120V Wiring

240V Wiring

4.3.2 240V hard-wiring installation

1. Remove the 4 screws securing the cord and cover plate to the side of the ﬁ rebox.

2. Unscrew the wire nuts securing the power supply cord and the L2 wire.

3. Install the new strain relief (supplied) (Fig. 4-2) into the new cover plate (supplied) and feed the 14/3

conductor wire through the strain relief.

4. Connect the ground/bond wires together.

5. Connect L1 to L1 of the appliance, connect the supply N wire to the single white N wire in the ﬁ rebox.

Connect the L2 wire to the L2 wire of the appliance.

6. Screw the wire nuts onto the blue N wire. Do not connect supply wires to this wire.

7. With wires secured, carefully feed the wires into the ﬁ rebox and re-secure the cover plate.

B x 1

C x 1

B x 1

C x 1

D x 1

Fig. 4-1

Fig. 4-2

HOME POWER

SUPPLY 240VAC

SOURCE

HOME POWER

SUPPLY 120VAC

SOURCE

APPLIANCE WIRE

HARNESS

APPLIANCE WIRE

HARNESS

Junction Box

Cover Plate Strain Relief

Inside

Appliance Outside

Appliance

Junction Box

Cover Plate Strain Relief

Inside

Appliance Outside

Appliance

W415-1980 / C / 03.25.22 17

5.0 operating instructions

• Ensure the house circuit breakers for the circuit supply are turned on. When initially connecting the appliance to

a power source, the appliance will make a beeping sound to indicate standby mode.

!WARNING

Once the appliance has been plugged into a grounded electrical outlet or hard-wired to a dedicated

120V or 240V power supply, it is ready to operate.

5.1 operating control panel

Power

Turns the appliance on / off.

Temperature

Control

Controls the appliance temperature.

11 Settings:

NOTE: When setting is °C or °F, the temperature control is OFF. Holding the button

for 5s will switch the temperature from °C to °F and vice versa.

Heater

Turns the heater and blower on / off.

3 Settings:

H0 - Heater and blower off

bL - Blower on

H1 - Heater on

NOTE: Heater function can be disabled / enabled by holding the button for 5s.

When the heater function is disabled, "LO" will be displayed.

Top

Light

Controls the top light colour.

8 Settings:

d1 - Yellow, red, and blue

d2 - Red and blue

d3 - Yellow and blue

d4 - Yellow and red

d5 - Blue

d6 - Red

d7 - Yellow

d0 - Off

Flame

Controls the ﬂ ame brightness.

5 Settings:

F0 - Flame off

F1 - Small ﬂ ame

F2 - Medium ﬂ ame

F3 - Bright ﬂ ame

F4 - Brightest ﬂ ame

°C 18 19 20 21 22 23 24 25 26 27

°F 64 66 68 70 72 74 76 78 80 82

W415-1980 / C / 03.25.22

operating instructions

5.2 operating remote control

Power

Turns the appliance on / off.

Timer

Turns the timer on /off.

10 Settings: -- (no setting), 30 min., 1h, 2h, 3h, 4h, 5h, 6h, 7h, 8h

Temperature

Control

Controls the appliance temperature.

11 Settings:

NOTE: When setting is °C or °F, the temperature control is OFF.

Holding the button for 5s will switch the temperature from °C to °F

and vice versa.

Flame

Controls the ﬂ ame brightness.

5 Settings:

F0 - Flame off

F1 - Small ﬂ ame

F2 - Medium ﬂ ame

F3 - Bright ﬂ ame

F4 - Brightest ﬂ ame

Top

Light

Controls the top light colour.

8 Settings:

d1 - Yellow, red, and blue

d2 - Red and blue

d3 - Yellow and blue

d4 - Yellow and red

d5 - Blue

d6 - Red

d7 - Yellow

d0 - Off

Brightness

Controls the ember bed brightness.

6 Settings:

b0 - No brightness

b1 - Low

b2 - Medium

b3 - Bright

b4 - Brightest

b5 - Pulsing effect (fade in and out)

Heater

Turns the heater and blower on / off.

3 Settings:

H0 - Heater and blower off

bL - Blower on

H1 - Heater on

NOTE: Heater function can be disabled / enabled by holding the

button for 5s. When the heater function is disabled, "LO" will be

displayed.

°C 18 19 20 21 22 23 24 25 26 27

°F 64 66 68 70 72 74 76 78 80 82

When operating the remote control, it must be directed towards the front centre of the appliance.

note:

W415-1980 / C / 03.25.22 19

operating instructions

Remote

(Rear Side)

Battery Holder

Battery (CR 2025)

A. To replace the existing battery, remove the

battery holder.

B. To remove the battery holder, turn remote onto

front side and press the left side lever towards

the center while pulling the battery holder out

using the slot provided.

C. Replace existing battery, type CR 2025, with a

new battery and reinstall the battery holder into

the remote by sliding it into position.

D. Battery holder is secure into the remote control

when a clicking noise is heard.

• This remote control requires button batteries that are hazardous to young children.

• WARNING! KEEP BATTERIES OUT OF REACH OF CHILDREN.

• Swallowing may lead to serious injury or death in as little as 2 hours due to chemical

burns and potential perforation of the oesophagus.

• If you suspect your child has swallowed or inserted a button battery, immediately seek

urgent medical assistance.

• Examine devices and make sure the battery compartment is correctly secured (i.e. that the screw or other

mechanical fastener is tightened). Do not use if compartment is not secure.

• Dispose of used button batteries immediately and safely. Flat batteries can still be dangerous.

• Tell others about the risks associated with button batteries and how to keep their children safe.

!WARNING

5.3 remote battery installation

6.0 maintenance

• Always turn the heater off and unplug the power cord from the outlet before cleaning, performing maintenance,

or moving this appliance. Failure to do so could result in electric shock, ﬁ re, or personal injury.

• Never immerse in water or spray with water. Doing so could result in electric shock, ﬁ re, or personal injury.

!WARNING

Metal:

• Buff using a soft cloth, slightly dampened with a citrus oil-based product.

• Do not use brass polish or household cleaners as these products will damage the metal trim.

Glass:

• Use a good quality cleaner sprayed onto a cloth or towel. Dry thoroughly with a paper towel or lint-free cloth.

• Never use abrasive cleaners, liquid sprays, or any cleaner that could scratch the surface.

Vents:

• Use a vacuum or duster to remove dust and dirt from the heater and vent areas.

Plastic:

• Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water.

• Never use abrasive cleaners, liquid sprays, or any cleaner that could scratch the surface.

W415-1980 / C / 03.25.22

For after-sales service, please call 1-866-820-8686.

7.0 replacement parts

!WARNING

• Failure to position the parts in accordance with this manual or failure to use only parts speciﬁ cally approved

with this appliance may result in property damage or personal injury.

Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts can

be ordered through your Authorized dealer / distributor.

For warranty replacement parts, a photocopy of the original invoice will be required to honour the

claim.

When ordering replacement parts always give the following information:

• Model & Serial Number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

Parts, part numbers, and availability are subject to change without notice.

Parts identiﬁ ed as stocked will be delivered within 2 to 5 business days for most delivery

destinations.

Parts not identiﬁ ed as stocked will be delivered within a 2 to 4 week period, for most cases.

Parts identiﬁ ed as ‘SO’ are special order and can take up to 90 days for delivery.

Care must be taken when removing and disposing of any broken glass or damaged components. Be sure to

vacuum up any broken glass from inside the appliance before operation.

note:

La page charge ...

NAPOLEON NEFB36H-BS Manuel utilisateur

Marque: NAPOLEON

Modèle: NEFB36H-BS

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: NAPOLEON NEFB36H-BS User manual

NAPOLEON NEFB36H-BS Manuel utilisateur

NAPOLEON NEFB36H-BS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents