NAPOLEON BX42NTRE Vent Natural Gas Fireplace Manuel utilisateur

FRENCH PG. 69

W415-2920 / B / 04.26.22

ADD MANUAL TITLE

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleon.com • [email protected]

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

NATURAL GAS MODELS:

PROPANE GAS MODELS:

Product Name / Code

(MUST use title from Price Book)

ADD ____ ILLUSTRATED

ADD PRODUCT IMAGE

CSA /

INTERTEK

LOGO

SAFETY INFORMATION

- Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the vicinity of

this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the ﬁ re department.

- Installation and service must be

performed by a qualiﬁ ed installer, service

agency, or the supplier.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certiﬁ ed kit is used.

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

WARNING

!

ENGLISH

$10.00

FOR INDOOR USE ONLY

IF INSTALLATION + OPERATION, ADD SERIAL

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE

BARCODE LABEL ON THE OWNER’S MANUAL”

BX42PTRE

INSTALLATION MANUAL

BX42NTRE

PLACE BARCODE LABEL ON THE

OWNER’S MANUAL

Ascent™ BX42

Safety Barrier

PLACE BARCODE LABEL ON THE

OWNER’S MANUAL

W415-2920 / B / 04.26.22

EN

2

safety information

• This appliance is hot when operated and

can cause severe burns if contacted.

• Any changes or alterations to this

appliance or its controls can be

dangerous and is prohibited.

• Do not operate appliance before reading and

understanding operating instructions. Failure

to operate appliance according to operating

instructions could cause ﬁ re or injury.

• Ensure the glass door is opened or removed

when lighting the pilot for the ﬁ rst time and

when the gas supply has run out.

• Risk of ﬁ re or asphyxiation, do not operate

appliance with ﬁ xed glass removed and never

obstruct the front opening of the appliance.

• Do not connect 110 volts to the control valve,

with the exception of models; GSST8 and

GT8.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves, protective footwear, and safety glasses during

installation. Sheet metal edges may be sharp.

• Do not burn wood or other materials in this appliance.

• Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing

and operating the appliance.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at

test pressures above 1/2 psig. Close the manual shut-off valve before pressure testing gas line at test

pressures equal to or less than 1/2 psig (35mb).

• The appliance must not be operated at temperatures below freezing (32°F / 0°C). Allow the appliance

to warm to above freezing prior to operation, with the exception of models; GSS36, GSS42; these

appliances are suitable for 0°F / -18°C.

• Children and adults should be alerted to hazards of high surface temperature and should stay

away to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the

appliance. Toddlers, young children and others may be susceptible to accidental contact

burns. A physical barrier is recommended if there are at risk individuals in the house. To

restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers,

young children and other at risk individuals out of the room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from

furniture and draperies.

• Furniture or other objects must be kept a minimum of 4 feet (1.22m) away from the front of the appliance.

• Ensure you have incorporated adequate safety measures to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is off, it will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior

to operating the appliance.

• It is imperative that the control compartments, burners and circulating blower and its passageway in the

appliance and venting system are kept clean. The appliance and its venting system should be inspected

before use and at least annually by a qualiﬁ ed service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and

free from combustible materials, gasoline and other ﬂ ammable vapors and liquids.

• If the appliance shuts off, do not re-light until you provide fresh air. If appliance keeps shutting off, have it

serviced. Keep burner and control compartment clean.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not allow wind or fans to blow directly into the appliance. Avoid any drafts that alter burner ﬂ ame

patterns.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

!

DANGER

A barrier designed to reduce the risk of burns from the hot

viewing glass is provided with this appliance and must be

installed for the protection of children and other at-risk

individuals.

!WARNING

EN

W415-2920 / B / 04.26.22 3

safety information

!WARNING

• Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this

appliance.

• This appliance must not be connected to a chimney ﬂ ue pipe serving a separate solid fuel burning

appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system and any gas control which has

been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass

should be done by a licensed or qualiﬁ ed service person, if equipped.

• Do not strike or slam shut the appliance glass door, if equipped.

• Only doors / optional fronts certiﬁ ed with the appliance are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Carbon or soot should not occur in a vent free appliance as it can distribute into the living area of your

home. If you notice any signs of carbon or soot, immediately turn off your appliance and arrange to have

it serviced by a qualiﬁ ed technician before operating it again.

• If equipped, the screen must be in place (closed) when the appliance is in operation.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating

to prevent exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of

the exhaust escaping through these openings can also cause the surrounding combustible materials to

overheat and catch ﬁ re.

• Carbon monoxide poisoning may lead to death; early signs of carbon monoxide poisoning resemble the

ﬂ u, with headache, dizziness and/or nausea. If you have these signs, the appliance may not be working

properly. Get fresh air at once! Have appliance serviced. Some people; pregnant women, persons with

heart or lung disease, anemia, those under the inﬂ uence of alcohol, those at high altitudes are more

affected by carbon monoxide than others. Failure to keep the primary air opening(s) of the burner(s) clean

may result in sooting and property damage.

• As with any combustion appliance, we recommend having your appliance regularly inspected and

serviced as well as having a Carbon Monoxide Detector installed in the same area to defend you and

your family against Carbon Monoxide (not applicable for outdoor appliances).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,

discolouration or damage to decorations, a TV or other electronic components.

• For appliances equipped with a safety barrier; if the barrier becomes damaged, the barrier

shall be replaced with the manufacturer’s barrier for this appliance.

• Installation and repair should be done by a qualiﬁ ed service person. It is imperative that control

compartments, burners and circulating air passageways of the appliance be kept clean.

• For outdoor products only: this appliance must not be installed indoors or within any structure that

prevents or inhibits the exhaust gases from dissipating in the outside atmosphere.

• If applicable, the millivolt version of this appliance uses and requires a fast acting thermocouple. Replace

only with a fast acting thermocouple supplied by Wolf Steel Ltd.

!

WARNING

!

Disconnect the appliance main gas valve/control

from the supply piping when pressure testing that

system at pressures in excess of 1/2 psi (3.5 kPa).

Isolate the appliance with it’s shut off valve during

any pressure testing of the supply piping at

pressures equal to or less than 1/2 psi (3.5 kPa).

FIRE RISK HAZARD / DELAYED IGNITION

High supply pressure will damage the valve / controls.

Add California Prop 65 warning

!

WARNING:

This product can expose you to chemicals including lead and lead compounds,

which are known to the State of California to cause cancer, and chemicals including carbon

monoxide, which are known to the State of California to cause birth defects or other reproduc-

tive harm. For more information, go to www.P65Warnings.ca.gov.

W415-2920 / B / 04.26.22

EN

4

table of contents

1.0 general information 5

1.1 rates and efﬁ ciencies 5

1.2 installation overview 6

1.3 rating plate information 8

1.4 mobile home installation 8

1.5 hardware list 9

1.6 front frame installation 9

1.7 dimensions 10

1.8 optional heat management

system 11

2.0 venting requirements 12

2.1 typical venting installation 14

2.1.1 corner termination 15

2.2 minimum air terminal location

clearances 16

2.3 top exit - all terminations 17

2.4 rear exit - horizontal termination 18

2.5 rear exit - vertical termination 19

2.6 rear exit 20

2.7 rear exit shield (for rear vent only)

20

2.8 top exit 21

3.0 rough framing 23

3.1 minimum framing dimensions 23

3.2 minimum clearance to

combustible enclosures 24

4.0 venting installation 30

4.1 horizontal installation 30

4.2 vertical installation 31

4.3 using either ﬂ exible vent

components 32

4.3.1 horizontal air terminal installation

32

4.3.2 vertical air terminal installation 33

4.3.3 appliance vent connection 33

4.3.4 restricting vertical vents 34

5.0 electrical information 35

5.1 hard wiring connection 35

5.2 receptacle wiring diagram 35

5.3 electronic wiring diagram 35

5.4 battery back-up installation 36

5.5 initializing the transmitter for the

ﬁ rst time 37

5.6 wiring diagram 38

5.7 light & blower assembly wiring

diagrams 39

6.0 gas installation 40

7.0 nailing tab installation 40

8.0 operation 41

8.1 pilot-on-demand 42

9.0 finish framing 43

9.1 ﬂ ush 43

9.2 recess 44

10.0 finishing 45

10.1 safety barrier & glass door

installation / removal 45

10.2 hood installation 46

10.3 ﬁ nishing with non-combustibles 47

10.4 installing non-combustible board

48

10.5 minimum combustible mantel

clearances 49

10.6 clearances around appliance (TV

and valuable objects) 50

10.7 air ﬂ ow cover installation 51

10.8 log placement 52

10.9 glowing embers 54

10.10 charcoal embers 54

10.11 glass media placement 54

11.0 adjustments 55

11.1 venturi adjustment 55

11.2 pilot burner adjustment 55

11.3 ﬂ ame characteristics 56

12.0 maintenance 57

12.1 care of glass 57

12.2 annual maintenance 58

12.3 glass / door replacement 58

12.4 night light replacement 58

12.5 blower replacement 59

13.0 replacement parts 60

13.1 overview 61

13.2 valve train assembly 62

14.0 troubleshooting 63

15.0 warranty 66

16.0 service history 67

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves

the right to change or modify any information within this manual at any time without notice. Changes, other than

editorial are denoted by a vertical line in the margin.

note:

EN

W415-2920 / B / 04.26.22 5

standard checklist

1.0 general information

When the appliance is installed at elevations above 4,500ft (1372m), and in the absence of speciﬁ c recommendations

from the local authority having jurisdiction, the certiﬁ ed high altitude input rating shall be reduced at the rate of 4% for each

additional 1,000ft (305m). Expansion / contraction noises during heating up and cooling down cycles are normal

and are to be expected. Change in ﬂ ame appearance from “HI” to “LO” is more evident in natural gas than in

propane.

This appliance is approved for bathroom, bedroom and bed-sitting room installations and is certiﬁ ed for mobile

home installation.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certiﬁ ed kit is used.

The protective wrap on plated parts is best removed when the assembly is at room temperature but this can be

improved if the assembly is warmed, using a hair dryer or similar heat source.

This appliance is a decorative product. It is not a source of heat and not intended to burn solid fuel.

note:

Batteries must be disposed of according to the local laws and regulations. Some batteries may be

recycled, and may be accepted for disposal at your local recycling center. Check with your

municipality for recycling instructions.

1.1 rates and efﬁ ciencies

Fuel Type Natural Gas Propane

Altitude (FT) 0-4,500

Max. Input (BTU/hr) 30,000

Min. Inlet Gas Supply Pressure 4.5” w.c. (11mb) 11” w.c. (27mb)

Max. Inlet Gas Supply Pressure 7” w.c. (17mb) 13” w.c. (32mb)

Manifold Pressure (Under Flow

Conditions) 3.5” w.c. (9mb) 10” w.c. (25mb)

Installer: please ﬁ ll out appliance

checklist in the owner’s manual

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the

appliance and must be installed.

important:

Some components and/or media are packaged separately and must be installed in accordance with the

information in this manual.

*Max. inlet pressure not to exceed 13” w.c. (32mb).

W415-2920 / B / 04.26.22

EN

6

general information

1.2 installation overview

Recommended installation steps:

1. Determine venting requirements before deciding the ﬁ nal location of the appliance.

2. Install rough framing (refer to “rough framing” section).

3. Place the appliance in its ﬁ nal position.

4. Install nailing tabs (refer to “nailing tab installation” section).

5. Install appliance venting (refer to “venting installation” section).

6. Install all electrical wirings (refer to “electrical information” section).

7. Install gas lines (refer to “gas installation” section).

8. Test appliance.

9. Complete framing (refer to “ﬁ nish framing” section).

10. Finishing (refer to “ﬁ nishing” section).

Safety Barrier

10 95

4

6

732

For Universal Heat Management installation steps, refer to the leaﬂ et provided with the Universal Heat

Management kit. Start Universal Heat Management installation before placing appliance in its ﬁ nal position.

note:

EN

W415-2920 / B / 04.26.22 7

general information

!WARNING

• Always light the pilot whether for the ﬁ rst time or if the gas supply has run out, with the glass door opened

or removed.

• Provide adequate clearance for servicing and operating the appliance.

• Provide adequate ventilation.

• Never obstruct the front opening of the appliance.

• Objects placed in front of the appliance must be kept a minimum of 48” (121.9cm) from the front face of

the appliance.

• Surfaces around and especially above the appliance can become hot. Avoid contact when appliance is

operating.

• Fire risk. Explosion hazard.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at test

pressures above 1/2 PISG (35mb). Close the manual shut-off valve before pressure testing gas line at test

pressures equal to or less than 1/2 PISG (35mb).

• Use only Wolf Steel approved optional accessories and replacement parts with this appliance using non-

listed accessories (blowers, doors, louvres, trims, gas components, venting components, etc.) could result

in a safety hazard and will void the warranty and certiﬁ cation.

• The appliance must not be operated at temperatures below freezing (32ºF/0ºC). Allow the appliance to

warm to above freezing prior to operation.

THIS GAS APPLIANCE MUST BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local

codes. Installation practices vary from region to region and it is important to know the speciﬁ cs that apply to your area, for

example in the state of Massachusetts:

• This product must be installed by a licensed plumber or gas ﬁ tter when installed within the commonwealth of

Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of an appliance insert or gas

log.

• The appliance off valve must be a “T” handle gas cock.

• The ﬂ exible connector must not be longer than 36 inches (0.9m).

• A carbon monoxide detector is required in all rooms containing gas ﬁ red appliances.

• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed

combustion product.

The installation must conform with local codes or, in absence of local

codes, the National Gas and Propane Installation Code CSA B149.1

in Canada, or the National Fuel Gas Code, ANSI Z223.1 / NFPA 54

in the United States. Suitable for mobile home installation if installed

in accordance with the current standard CAN/CSA Z240MH Series,

for gas equipped mobile homes, in Canada or ANSI Z223.1 and

NFPA 54 in the United States.

The appliance and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing

of that system at test pressures in excess of 1/2 psig (35 mb).

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any

pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (35 mb). When installed

with a blower or fan, the junction box must be electrically connected and grounded in accordance with local codes. In the

absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI / NFPA 70 National

Electric Code in the United States. In the case where the blower is equipped with a power cord, it must be connected into a

properly grounded receptacle. The grounding prong must not be removed from the cord plug.

The following does not apply to inserts; as long as the required clearance to combustibles is maintained, the most desirable

and beneﬁ cial location for an appliance is in the center of a building, thereby allowing the most efﬁ cient use of the heat

created. The location of windows, doors and, the trafﬁ c ﬂ ow in the room where the appliance is to be located should be

considered. If possible, you should choose a location where the vent will pass through the house without cutting a ﬂ oor or

roof joist. If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood ﬂ ooring, the

appliance shall be installed on a metal or wood panel extending the full width and depth, unless otherwise tested.

We suggest that our gas

hearth products be installed

and serviced by professionals

who are certied in the U.S.

by the National Fireplace

Institute

®

(NFI) as NFI Gas

Specialists

www.ncertied.org

W415-2920 / B / 04.26.22

EN

8

general information

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

1.3 rating plate information

The rating plate must remain with the appliance at all times. It must not be removed.

note:

1.4 mobile home installation

This appliance must be installed in accordance with the manufacturer’s instructions and the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home

Standard, CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas

indicated on the rating plate.

This mobile/manufactured home listed appliance comes factory equipped with a means to secure the appliance. Built

in appliances are equipped with 1/4” (6.4mm) diameter holes located in the front left and right corners of the base.

Use appropriate fasteners, inserted through the holes in the base to secure. For free standing products contact your

local authorized dealer / distributor for the appropriate securing kit. For mobile home installations, the appliance must

be fastened in place. It is recommended that the appliance be secured in all installations. Always turn off the pilot and

the fuel supply at the source, prior to moving the mobile home. After moving the mobile home and prior to lighting the

appliance, ensure that the logs are positioned correctly.

This appliance is certiﬁ ed to be installed in an aftermarket permanently located, manufactured (mobile) home,

where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible

for use with other gases, unless a certiﬁ ed kit is used.

Conversion Kits

This appliance is ﬁ eld convertible between Natural Gas (NG) and Propane (P).

To convert from one gas to another, consult your Authorized dealer/distributor.

Certiﬁed to Canadian and American National Standards: CSA 2.22-XXXX / ANSI Z21.50-XXXX for Vented Decorative Gas Appliances

Certiﬁé selon les normes Nationales Canadiennes et Américaines: CSA 2.22-XXXX / ANSI Z21.50-XXXX pour les Appareils à gaz décoratif à évacuation

Direct vent, vented gas ﬁreplaces. Approved for bedroom, bathroom and bed-sitting room installation. Suitable for mobile home installation, if installed in accordance with the current

standard CAN / CSA Z240MH Series gas equipped mobile homes in Canada, or, in the United States, the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part

3280. When this US Standard is not applicable, use the Standard for Fire Safety Criteria for Manufactured Home Installations, Sites and Communities, ANSI / NFPA 501A. This appliance

must be installed in accordance with local codes, if any; if none, follow the current ANSI Z223.1 or CSA B149. For use with barrier WXXX-XXXX. Follow installation instructions.

Foyer à gaz ventilé. Homologué pour installation dans une chambre à coucher, une salle de bain et un studio. Approprié pour installation dans une maison mobile si son installation

conforme aux exigences de la norme CAN / CSA Z240MH Séries de maisons mobile équipées au gaz en vigueur au Canada, ou, aux États-Unis selon la norme 24 CFR, Part 3280,

Manufactured Home Construction and Safety Standard. Dans le cas ou cette norme d’États-Unis n’est pas pertinentes, utiliser la norme NFPA 501A, Fire Safety Criteria for Manufactured

Home Installations, Sites and Communities. Installer l’appareil selon les codes ou règlements locaux ou, en l’absence de tels règlements, selon les codes d’installation ANSI Z223.1 ou

CSA B149 en vigueur. Utiliser uniquement avec l’écran WXXX-XXXX. Suivre les instructions d’installation.

9700539 (WSL) 4001658 (NAC) 4001657 (NGZ) 4001659 (WUSA)

WOLF STEEL LTD. 24 Napoleon Road, Barrie, ON, L4M 0G8 Canada

XXXX XXXX XXXX XXXX

MODEL / MODÈLE

Altitude

Input

Reduced Input

P4

Élévation

Alimentation

Alimentation Réduite

P4

Manifold Pressure: 3.5” w.c. (NG)

Minimum Supply Pressure: 4.5” w.c. (NG)

Maximum Supply Pressure: 7”* w.c. (NG)

Pression au Collecteur: 3,5” d’une colonne d’eau (GN)

Pression d’Alimentation Min.: 4,5” d’une colonne d’eau (GN)

Pression d’Alimentation Max.: 7” ** d’une colonne d’eau (GN)

** Maximum inlet pressure not to exceed 13”.

Manifold Pressure: 10” w.c. (P)

Minimum Supply Pressure: 11” w.c. (P)

Maximum Supply Pressure: 13”* w.c. (P)

Pression au Collecteur: 10” d’une colonne d’eau (P)

Pression d’Alimentation Min.: 11” d’une colonne d’eau (P)

Pression d’Alimentation Max.: 13” * d’une colonne d’eau (P)

** Pression d’alimentation maximale ne devait pas dépasser 13”.

0-XXXXft (0-XXXXm)

Minimum clearance to combustible materials:

Top, sides & back: per standoff spacers for framing and ﬁnishing

materials. For non-combustible framing and ﬁnishing materials,

see installation manual.

Top X”

Floor X”

Sides X”

Back X”

Vent top X”

Vent sides & bottom X”

Recessed depth X”

*** Mantel X” from appliance opening

Dégagements minimaux des matériaux combustibles:

Dessus, côtés et arrière: selon les espaceurs de dégagements

pour les matériaux d’ossature selon le manuel du propriétaire

pour les matériaux de ﬁnition.

Dessus X”

Plancher X“

Côtés X”

Arrière X“

Dessus du conduit d’évent X”

Côtés et dessous du conduit d’évent X”

Profondeur d’encastré une face X”

*** Tablette X” de l’ouverture de l’appareil

WARNING: Do not add any material to the appliance which will come in contact with the

ﬂames, other than that supplied by the manufacturer with the appliance.

AVERTISSEMENT: N’ajoutez pas à cet appareil aucun matériau devant entretien

contact avec les ﬂammes autre que celui qui est fourni avec cet appareil par le fabricant.

*** Maximum horizontal extension:

X”. See installation manual for

greater extensions, minimum vent

lengths and maximum vent lengths.

*** L’extension horizontale maximale: X”.

Référez au manuel d’installation pour des

extensions plus grandes, les longueurs

d’évacuation minimaux et maximum.

The appliance must be vented using the appropriate Napoleon vent kits. See installation

manual for venting speciﬁcations. Proper reinstallation and resealing is necessary after servicing

the vent-air intake system.

L’appareil doit être ventilé à l’aide de l’ensemble d’évacuation propre à Napoleon. Référez au

manuel d’installation pour les spéciﬁcations d’évacuation. Il est nécessaire de bien réinstaller et

resceller l’évacuation après avoir executer l’entretien du système de prise d’air.

Serial Number / N° de Série:

W385-XXXX

REFERENCE# 161746

XXXX

VENTED DECORATIVE GAS APPLIANCE: NOT A SOURCE OF

HEAT, NOT INTENDED FOR USE AS A HEATING

APPLIANCE, NOT FOR USE WITH SOLID FUEL.

APPAREIL À GAZ DÉCORATIF À ÉVACUATION: N’EST PAS

UNE SOURCE DE CHALEUR; N’EST PAS DESTINÉ À ÈTRE

UTILISÉ COMME UN APPAREIL DE CHAUFFAGE; NE

CONVIENT PAS AUX COMBUSTIBLES SOLIDES.

FOR USE WITH GLASS DOORS CERTIFIED WITH THIS APPLIANCE ONLY.

POUR UTILISATION UNIQUEMENT AVEC LES PORTES EN VERRE

CERTIFIÉES AVEC L’APPAREIL.

XX,XXX XX,XXX

For natural gas when equipped with No. XX drill size oriﬁce.

For propane when equipped with No. XX drill size oriﬁce.

Convient au gaz naturel quand l’appareil est muni d’un injecteur de diamètre no. XX.

Convient au propane quand l’appareil est muni d’un injecteur de diamètre no. XX.

Electrical rating: 115V, 60HZ. Less than 12 amperes. Spéciﬁcations électriques: 115V, 60HZ. Moins de 12 ampère.

XX.X% XX.X%

XXXX XXXX XXXX XXXX

SAMPLE

ceses

z décoratif à évacuadécoratif à évacu

n accordance with the current accordance with the current

fety Standard, Title 24 CFR, Part Standard, Title 24 CFR, Pa

ities

,

ANSI / NFPA 501A. This a

pp

liance

I / NFPA 501A. This appliance

XXX. Follow installation instructions.nstallation instructions.

ans une maison mobile si son installation le si son installation

tatat

s-Unis selon la norme s

2

4

C

FR, Part 3280,

4 CFR, Part 3280,

me me

NFPA 501A, Fire Safety Criteria for ManufactureNFPA 501A, Fire Safety Criteria for Manufactur

ements, selon les codes d’installation ANSI Z223.1 onts, selon les codes d’installation ANSI Z223.1

oleon Road, Baroleon Road, Bar

XXX

É

lévation

Élévation

A

lim

e

nt

a

ti

o

n

Alimentation

A

limentation R

é

duite

Alimentation Réduite

P4P4

Ma

nif

o

l

d

P

r

essu

r

e

:

nifold Pressure

1

0” w.c.

(

P

)w.c. (P)

Minimum Supply Pressure:pply Pressure:

11” w.c.

(

P

)11” w.c. (P)

Maximum Su

pp

l

y

Pressure:

Maximum Supply Pressure:

1

3”* w.c.

(

P

)13”* w.c. (P)

sion au Collecteur:on au Collect

10” d’une colonne d’eau

(

P

)0” d’une colonne d’ea

d’Alimentation Min.:Alimentation Min.:

11” d’une colonne d’eau (P11” d’une colonne d’eau

n d’Alimentation Max.: mentation Max.:

13” * d’une colonne d’eau13” * d’une colonne d’ea

ssion d’alimentation maximale ne devait pas dépasstation maximale ne devait pas dépas

Dégagements minimaux des matériaux combDégagements minimaux des matériaux co

Dessus, côtés et arrière: selon les espaceurs de dDessus, côtés et arrière: selon les espaceurs de

pour les matériaux d’ossature selon le manuepour les matériaux d’ossature selon le manu

pour les mpour l

C

on:

VENTED DECORATIVE GASVENTED DECORATIVE GAS

HEAT, NOTHEAT, NOT

APPLIAAPPLI

APPAREIL À GAAPPAREIL À GA

UNE SOUR

UT

FOFO

12 amperes.peres.

XXXXXXX

EN

W415-2920 / B / 04.26.22 9

general information

1.5 hardware list

Ref. # Description Quantity

1 Self-drilling screw 2

21/4” Hex, 1/2” long sheet metal screw 28

32 1/2” long sheet metal screw 4

4Quad drive sheet metal screw 4

5Sheet metal screw 4

6 Pan head quad screw 4

Only fasteners supplied with the appliance will be illustrated.

note:

1.6 front frame installation

23

45

1

6

Install the front frame using 6 screws

(supplied).

The front frame must be installed.

note:

#2 X6

W415-2920 / B / 04.26.22

EN

10

general information

1.7 dimensions





PP





PP





PP





PP





PP



*$6

,1/(7





PP





PP





PP



PP





PP



Front View Side View Top View

Safety Barrier

EN

W415-2920 / B / 04.26.22 11

general information

1.8 optional heat management system

The Universal Heat Management system is an optional gravity vent kit that allows you to manage the heat

produced by the appliance at and around the ﬁ replace.

We recommend installing the Universal Heat Management system kit during the installation of the appliance

BEFORE the gas is installed.

For more information, contact your local authorized dealer.

Reduced mantel

clearances

Grill to expel

warm air into the

room

Reduced

temperatures

above fireplace

W415-2920 / B / 04.26.22

EN

12

venting requirements

2.0 venting requirements

!WARNING

• Risk of ﬁ re. Maintain speciﬁ ed air space clearances to vent pipe and appliance.

• The vent system must be supported every 3’(0.9m) for both vertical and horizontal runs. Use support ring assembly

W010-0067 or equivalent non-combustible strapping to maintain the minimum clearance to combustibles for both

vertical and horizontal runs. Spacers are attached to the inner pipe at predetermined intervals to maintain an even air

gap to the outer pipe. This gap is required for safe operation. A spacer is required at the start, middle, and end of each

elbow to ensure this gap is maintained. These spaces must not be removed.

This appliance uses a 5” (127mm) exhaust / 8” (203.2mm) air intake vent pipe system. Refer to the section

applicable to your installation.

For safe and proper operation of the appliance follow the venting instructions exactly. Deviation from the minimum vertical

vent length can create difﬁ culty in burner start-up and/or carboning. Under extreme vent conﬁ gurations, allow several

minutes (5-15) for the ﬂ ame to stabilize after ignition. Although not a requirement, it is recommended for vent lengths that

pass through unheated spaces (attics, garages, crawl spaces) be insulated with the insulation wrapped in a protective sleeve

to minimize condensation. Provide a means for visually checking the vent connection to the appliance after the appliance is

installed. Use a ﬁ restop, vent pipe shield or attic insulation shield when penetrating interior walls, ﬂ oor or ceiling.

The vent terminal may be painted with a high temperature paint to match exterior colours. Use an outdoor paint suitable for

400°F (200°C). Application and performance of paint is the consumer’s responsibility. Spot testing is recommended.

Connections made by means of an adaptor at the appliance, as well as the connection at the vent terminal must be sealed.

RTV sealant may be used on both the inner exhaust and outer intake vent pipe joints of all other approved vent systems, ex-

cept for the exhaust vent pipe connection to the appliance ﬂ ue collar which must be sealed using the black high temperature

sealant Mill Pac.

For all vent systems is strongly recommend for all installations but required when power venting the appliance, that the outer

air intake joints are sealed using either high temperature silicone (RTV) or a suitable aluminum tape that covers each joint in

the vent system entirely around its circumference. This will ensure the best performance in every application and avoids per-

formance or condensation concerns that may occur in “tightly” constructed homes, particularly those in cold climates.

Use only Wolf Steel, Metal-Fab, BDM, Simpson Dura-Vent, or Selkirk Direct Temp venting components. Minimum and

maximum vent lengths, for both horizontal and vertical installations, clearances from vent pipes to combustibles and air

terminal locations as set out in this manual apply to all vent systems and must be adhered to. For Metal-Fab, BDM, Simpson

Dura-Vent, or Selkirk Direct Temp, follow the installation procedure provided with the venting components or on the website

for your venting supplier.

A starter adaptor must be used with the following vent systems and may be purchased through Wolf Steel or from the

corresponding supplier listed below:

If for any reason the vent air intake system is disassembled; reinstall per the instructions provided for the initial

installation.

This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing alternate

constructions, such as a chimney as part of the vent system, is not permitted.

note:

Venting System Manufacturer Starter Adapter

Part Number Supplier Website

SureSeal Metal-Fab 5DNA Wolf Steel www.mtlfab.com

Direct Vent Pro Simpson DuraVent W175-0170 Wolf Steel www.duravent.com

Pro-Form BDM N/A BDM www.dalsinmfg.com

Direct Temp Selkirk 5DT-AAN Selkirk www.selkirkcorp.com

Ventis Olympia Chimney

and Venting VDV-NA05-58F Olympia Chimney

and Venting www.olympiachimney.com

All vent measurements start at the base of the air collar of the appliance.

When using Wolf Steel venting components, use only approved Wolf Steel rigid / ﬂ exible components with the following ter-

mination kits: wall terminal kit GD422-1, GD422R-2, ST58U-1 or 1/12 to 7/12 pitch roof terminal kit GD410, 8/12 to 12/12

roof terminal kit GD411, ﬂ at roof terminal kit GD412 or periscope kit GD401 (for wall penetration below grade). With ﬂ exible

venting, in conjunction with the various terminations, use either the 5 foot (1.5m) vent kit GD420 or the 10 foot (3.1m) vent kit

GD430.

EN

W415-2920 / B / 04.26.22 13

venting requirements

For optimum ﬂ ame appearance and appliance performance, keep the vent length and number of elbows to a minimum.

The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that

it is unobstructed and undamaged.

Rigid and ﬂ exible venting systems must not be combined. Different venting manufacturer components must not

be combined.

These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal run is 20

feet (6.1m). The maximum allowable vertical vent length is 40 feet (12.2m). The maximum number of vent connections is two

horizontally or three vertically (excluding the appliance and the air terminal connections) when using ﬂ exible venting.

An insulated sleeve has been supplied and must be installed on all rear vent applications for the ﬁ rst

24” (61cm).

Horizontal runs may have a 0” (0mm) rise per foot/meter however for optimum performance it is recommended

that all horizontal runs have a minimum 1/4” (21mm) rise per foot/meter using ﬂ exible venting. For safe and proper

operation of the appliance, follow the venting instructions exactly.

A terminal shall not terminate directly above a sidewalk or paved driveway which is located between two single

family dwellings and serves both dwellings. Local codes or regulations may require different clearances.

Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼”

(31.8mm) air gap all around between the inner liner and outer liner is required for safe operation.

This appliance is certiﬁ ed for use with a power vent kit (top vent only). Contact your local authorized dealer for

more information.

W415-2920 / B / 04.26.22

EN

14

venting requirements

2.1 typical venting installation

12"

(30.5cm)

minimum

to grade

Special vent installation (periscope termination)

Use the periscope kit to locate the air termination above grade. The periscope must be installed so that when

ﬁ nal grading is completed, the bottom air slot is located a minimum 12” (30.5cm) above grade. The maximum

allowable vent length is 10’ (3m) for a ﬁ replace and 8’ (2m) for a stove.

base of air collar

TOP VENT REAR VENT

TOP VENT

24” (61cm)

Maximum

12” (30.5cm)

Minimum

45 5/8”

(115.8cm)

Minimum plus

rise*

20” (50.8cm)

Maximum

24 1/8” (61.3cm)

Minimum plus rise*

30” (76.2cm)

Minimum

*See “venting requirements” and

“venting installation” sections.

• The ﬁ rst 2 feet of outer 8” (203mm)

diameter vent pipe from the ap-

pliance must be wrapped in the

1” (25mm) thick insulation sleeve

(supplied).

!WARNING

• The ﬁ rst 2 feet of outer 8” (203mm)

diameter vent pipe from the ap-

pliance must be wrapped in the

1” (25mm) thick insulation sleeve

(supplied).

!WARNING

EN

W415-2920 / B / 04.26.22 15

venting requirements

16" (40.6cm)

minimum

40 FT (12M)

maximum

3 FT (1M)

minimum

base of air collar

20” (50.8cm)

MAXIMUM

6” (152mm)

RISE MINIMUM

2.1.1 corner termination

FLEX VENTING RIGID VENTING

The maximum vent length for a corner installation is 20” (50.8cm) of horizontal run, in addition to the 45° offset. In

this case, 0” rise is acceptable when using rigid venting. When using ﬂ exible venting, it is required to maintain a 6”

(152mm) rise. See illustrations below for more information.

W415-2920 / B / 04.26.22

EN

16

venting requirements

2.2 minimum air terminal location clearances

QMIN RMAX MAX

R

= 3 feet

(0.9m) = 2 x IHHW

(4.6m)

QACTUAL

INSTALLATIONS

CANADA U.S.A.

A12” (30.5cm) 12” (30.5cm) Clearance above grade, veranda porch, deck or balcony.

B12” (30.5cm)Δ9” (229mm) ΔClearance to windows or doors that open.

C12” (30.5cm)* 12” (30.5cm)* Clearance to permanently closed windows.

D18”

(45.7cm)**

18”

(45.7cm)**

Vertical clearance to ventilated sofﬁ ts located above the terminal within a horizontal distance of 2’ (0.6m)

from the center line of the terminal.

E12” (30.5cm)** 12” (30.5cm)** Clearance to unventilated sofﬁ t.

F0” (0mm) 0” (0mm) Clearance to an outside corner wall.

G0” (0mm)*** 0” (0mm)*** Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).

2” (51mm)*** 2” (51mm)*** Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).

H3’(0.9m) 3’(0.9m)**** Clearance to each side of the center line extended above the meter / regulator assembly to a maximum

vertical distance of 15’ (4.6m).

I3’ (0.9m) 3’ (0.9m)**** Clearance to a service regulator vent outlet.

J12” (30.5cm) 9” (229mm) Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.

K6’ (1.8m) 3’ (0.9m) † Clearance to a mechanical air supply inlet.

L7’ (2.1m) ‡ 7’ (2.1m) **** Clearance above a paved sidewalk or paved driveway located on public property.

M12” (30.5cm)†† 12” (30.5cm)**** Clearance under a veranda, porch, deck or overhang.

N16” (40.6cm) 16” (40.6cm) Clearance above the roof.

O2’ (0.6m)†* 2’ (0.6m) †* Clearance from an adjacent wall including neighbouring buildings.

P8’ (2.4m) 8’ (2.4m) Roof must be non-combustible without openings.

Q3’ (0.9m) 3’ (0.9m) See chart for wider wall dimensions.

R6’ (1.8m) 6’ (1.8m) See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an opening

between the terminal and the open side of the structure.

S12” (30.5cm) 12” (30.5cm) Clearance under a covered balcony

Δ The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.

* Recommended to prevent condensation on windows and thermal breakage

** It is recommended to use a heat shield and to maximize the distance to vinyl clad sofﬁ ts.

*** The periscope requires a minimum 18 inches clearance from an inside corner.

**** This is a recommended distance. For additional requirements, check local codes.

† 3 feet above if within 10 feet horizontally.

‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.

†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the ﬂ oor.

†* Recommended to prevent recirculation of exhaust products. For additional requirements, check local codes.

††* Permitted only if the balcony is fully open on a minimum of one side.

Wall terminals are for illustration purposes only. Size and shapes may vary. Wall terminal

measurements taken from the exhaust outlet, not the mounting plate.

Covered balcony applications ††*

R

QS

GP

Clearances are to be in accordance with local

installation codes and the requirements of the gas

supplier. In their absence, clearances are to be as

listed above and are based on national codes.

note:

EN

W415-2920 / B / 04.26.22 17

venting requirements

2.3 top exit - all terminations

0’

Base of

air collar 10’

10’

15’

20’ 25’

20’

30’

40’

5’

2’

(24”)

1’ min.

(12”)

5’

1 elbow zone

1-2 elbow zone

1-3 elbow zone

1-4 elbow zone

1-5 elbow zone

1-6 elbow zone

H

V

V+H ≤ 40 ft. (For longer vent runs, a power

vent is required).

H ≤ 20 ft.

V + H are measured from the centre of vent

elbows. Elbows are considered as 90º.

Two 45º elbows = One 90º elbow.

3’ min.

(36”)

38 1/2’

(462”)

Vertical termination only.

No horizontal termination allowed.

W415-2920 / B / 04.26.22

EN

18

venting requirements

2.4 rear exit - horizontal termination

0’

0’ 10’

10’

15’

20’ 25’

20’

30’

40’

5’

1 1/2’

(18”)

1 1/2’

(18”)

35 3/4’

(429”)

5’

1-2 elbow zone

1-3 elbow zone

1-4 elbow zone

H

V

(For vent runs that exceed the graph

parameters, a power vent is required).

V + H are measured from the centre of vent

elbows. Elbows are considered as 90º.

Two 45º elbows = One 90º elbow.

4 3/4’

(57”)

17 1/4’

(207.6”)

1-5 elbow zone

EN

W415-2920 / B / 04.26.22 19

venting requirements

2.5 rear exit - vertical termination

10’

15’

20’

25’

20’

30’

40’

5’

39’

(468”)

1 elbow zone

1-2 elbow zone

1-3 elbow zone

H

V

(For vent runs that exceed the graph

parameters, a power vent is required).

V + H are measured from the centre of vent

elbows. Elbows are considered as 90º.

Two 45º elbows = One 90º elbow.

0’

1’

(12”)

3

(36”)

5’

4 3/4’

(57”)

1-4 elbow zone

1-5 elbow zone

1-6 elbow zone

W415-2920 / B / 04.26.22

EN

20

venting requirements

2.6 rear exit

A. Remove the safety barrier and glass front (see "safety barrier

& door removal / installation" section).

B. Remove the contents from the ﬁ rebox and set aside. You will

need the exhaust ﬂ ue collar and the top bafﬂ e (supplied).

C. To ease assembly, remove the four hex head screws

securing the deﬂ ector from inside the top front of the ﬁ rebox

(Fig. 1). Set deﬂ ector aside.

D. Remove the four screws securing the rear heat shield, set

aside the shield. Remove the four screws securing the

gasket and outer coverplate. (Fig. 2).

E. Secure the gasket and the 8” intake collar provided to the

rear opening and replace the rear heat shield.

F. Secure the gasket (provided in the manual baggie)

and the outer coverplate over the top opening of the

appliance. Secure the ﬂ ue collar assembly, gasket and

rear exit shield using the four hex head 3/8" thread cutting

screws (Fig. 3).

G. Replace the deﬂ ector. Rest the front edge of the top bafﬂ e in the four slots

on the deﬂ ector. Rest the rear edge of the top bafﬂ e (complete with deﬂ ector)

on the tabs of the ﬂ ue collar assembly. Reattach the deﬂ ector (complete with

top bafﬂ e) using the four screws removed in step C (Fig. 4). Install the log set,

glass door and safety barrier.

DEFLECTOR

É

Fig. 1

2.7 rear exit shield (for rear vent only)

A. Loosen the two screws, that secure the exhaust

plate, and slide the bafﬂ e in place by sliding its slotted

openings behind the screwheads, tighten the two

previously loosened screws. Refer to the illustration.

B. Reinstall the door and safety barrier assembly on

the appliance (see “safety barrier & door removal /

installation” section).

!WARNING

• Failure to create a seal to the ﬁ rebox with the exhaust collar assembly will cause the appliance to function

improperly and can cause injury or property damage.

Do not overtighten. The gasket needs only to be snug against the ﬁ rebox.

note:

This shield is used to block the view through the

venting to the outdoors.

note:

Deﬂector

Top

bafﬂe

Flue collar

assembly

Fig. 4

Fig. 2

OUTER

COVERPLATE

GASKET

HEAT

SHIELD

Fig. 3

La page charge ...

NAPOLEON BX42NTRE Vent Natural Gas Fireplace Manuel utilisateur

NAPOLEON BX42NTRE Vent Natural Gas Fireplace Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents