NAPOLEON Plazmafire 48 Le manuel du propriétaire

W415-1606 / C / 11.08.17

FRENCH

PG.49

ADD MANUAL TITLE

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleonﬁ replaces.com • hearth@napoleonproducts.com

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

NATURAL GAS MODELS:

PROPANE GAS MODELS:

PRODUCT NAME™

ADD ____ ILLUSTRATED

ADD PRODUCT IMAGE

CSA /

INTERTEK

LOGO

SAFETY INFORMATION

- Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the vicinity of

this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the ﬁ re department.

- Installation and service must be

performed by a qualiﬁ ed installer, service

agency, or the supplier.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certiﬁ ed kit is used.

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

WARNING

!

ENGLISH

$10.00

FOR INDOOR USE ONLY

SAFETY BARRIER

Plazmaﬁre™ 48

(WHD48)

WHD48N

WHD48P

INSTALLATION AND

OPERATION MANUAL

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel

Ltd. reserves the right to change or modify any information within this manual at any time without

notice. Changes, other than editorial are denoted by a vertical line in the margin.

note:

W415-1606 / C / 11.08.17

EN

2

table of contents

1.0 installation overview 3

2.0 safety information 4

3.0 general information 6

3.1 dimensions 6

3.2 hardware list 7

3.3 general instructions 8

3.4 rating plate information 9

4.0 venting 10

4.1 venting lengths and components 11

4.2 typical vent installation 12

4.3 special vent installations 12

4.3.1 periscope termination 12

4.4 vent terminal clearances 13

4.5 horizontal termination 14

4.6 vertical termination 15

5.0 installation 16

5.1 mounting plate installation (for typical

drywall construction) 17

5.2 mounting plate installation (for concrete) 18

5.3 using ﬂexible vent components 18

5.3.1 appliance vent connection 19

5.3.2 vertical installation 19

5.3.3 horizontal air terminal installation 19

5.3.4 vertical air terminal installation (ﬂexible) 20

5.4 mounting the appliance 21

5.5 gas installation 22

5.6 mobile home 22

5.7 minimum clearance to combustibles and

non-combustibles 23

5.8 receiver location / wiring 24

6.0 finishing 25

6.1 housing panel installation 25

6.2 door removal / installation 26

6.3 glass media 26

6.4 surround installation / removal 27

6.5 logo placement 27

7.0 electrical information 28

7.1 hard wiring connection 28

7.2 wiring diagram 28

7.3 receptacle wiring diagram 29

8.0 operation 30

8.1 operating instructions 30

8.2 lighting instructions 30

8.3 general transmitter layout 31

8.5 temperature display 32

8.6 ﬂame height time 32

8.4 Initializing the transmitter/battery holder

for the ﬁrst time 32

8.7 LED on/off light control 33

8.8 continuous pilot / intermittent pilot (CPI /

IPI) selection 33

8.9 child proof function 34

8.10 low battery / manual bypass 34

8.11 in the event of a power failure 34

8.12 manual operation 34

9.0 adjustments 35

9.1 pilot burner adjustment 35

9.2 venturi adjustment 35

9.3 ﬂame characteristics 35

10.0 maintenance 36

10.1 annual maintenance 36

10.2 care of glass 37

10.3 care of plated parts 37

10.4 door glass replacement 37

11.0 replacements 38

11.1 overview 39

11.2 valve train assembly 40

12.0 accessories 41

13.0 troubleshooting 42

14.0 warranty 45

15.0 service history 46

16.0 notes 47

WALL INSTALL

This drawing is the property of Wolf Steel LTD. or NAC.

It is not to be reproduced nor used in any manner

without our consent. All rights are reserved.

2

08/27/14 AGR

UNLESS OTHERWISE NOTED OR DEPICTED

ALL DIMENSIONS ARE OUTSIDE IN INCHES

ALL SURFACES ARE CONSIDERED CLASS "D"

REFER TO ENG-009 AND ENG-010

FOR SURFACE FINISH CRITERIA

TOLERANCES:

A

B

C

D

B

A

C

D

1 2 3 4 5 7 8

8

754321

SAFETY BARRIER

Mantel, see

“minimum

clearance to

combustibles

and non-

combustibles ”

section.

Venting, see

“venting” and

“installation” sections.

Rating plate, see “rating plate

information”

section.

Side Wall, see

“minimum clearances to

combustibles and non-

combustibles”

section.

Surround, see

“ﬁnishing” section.

EN

W415-1606 / C / 11.08.17

3

installation overview

1.0 installation overview

W415-1606 / C / 11.08.17

EN

4

safety information

2.0 safety information

• This appliance is hot when operated and can

cause severe burns if contacted.

• Any changes to this appliance or its control

can be dangerous and are prohibited.

• Do not operate appliance before reading and

understanding operating instructions. Failure

to operate appliance according to operating

instructions could cause ﬁ re or injury.

• Risk of ﬁ re or asphyxiation do not operate

appliance with ﬁ xed glass removed.

• Do not connect 110 volts to the control valve.

• Risk of burns. The appliance should be turned

off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves, protective footwear, and safety glasses during

installation. Sheet metal edges may be sharp.

• Children and adults should be alerted to the hazards of high surface temperature and should stay away

to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children, and others may be susceptible to accidental contact burns. A physical barrier

is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,

install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the

room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and

draperies.

• Ensure you have incorporated adequate safety measures to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is off, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior to

operating the appliance.

• The appliance is a vented gas-ﬁ red appliance. Do not burn wood or other materials in the appliance.

• The appliance area must be kept clear and free from combustible materials, gasoline and other

ﬂ ammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁ ed.

• This appliance must not be connected to a chimney ﬂ ue pipe serving a separate solid fuel burning

appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system and any gas control which has

been under water.

LA VITRE CHAUDE CAUSERA

DES BRÛLURES.

NE PAS TOUCHER LA VITRE

AVANT QU’ELLE AIT REFROIDI.

NE JAMAIS LAISSER LES

ENFANTS TOUCHER LA VITRE.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

!

DANGER

!

AVERTISSEMENT

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with this appliance and

shall be installed for the protection of children and other

at-risk individuals.

Une barriére conçu à réduire le risque de brûlures

causées par le verre chaud est fourni avec l’appareil et

sera installé pour la protection des enfants et d’autres

personnes à risque.

3.1

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass

should be done by a licensed or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating to

prevent exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of the

exhaust escaping through these openings can also cause the surrounding combustible materials to overheat

and catch ﬁ re.

• Only doors / optional fronts certiﬁ ed with the unit are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all

plastic bags, these are not toys and should be kept away from children and infants.

• As with any combustion appliance, we recommend having your appliance regularly inspected and serviced

as well as having a carbon monoxide detector installed in the same area to defend you and your family

against carbon monoxide.

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.

Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or

damage to decorations, a T.V. or other electronic components.

• A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and

shall be installed.

• If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this

appliance.

• Installation and repair should be done by a qualiﬁ ed service person. The appliance should be inspected

before use and at least annually by a professional service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments,

burners and circulating air passageways of the appliance be kept clean.

!

WARNING

!

WARNING

EN

W415-1606 / C / 11.08.17

5

safety information

• This appliance is hot when operated and can

cause severe burns if contacted.

• Any changes to this appliance or its control

can be dangerous and are prohibited.

• Do not operate appliance before reading and

understanding operating instructions. Failure

to operate appliance according to operating

instructions could cause ﬁ re or injury.

• Risk of ﬁ re or asphyxiation do not operate

appliance with ﬁ xed glass removed.

• Do not connect 110 volts to the control valve.

• Risk of burns. The appliance should be turned

off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves, protective footwear, and safety glasses during

installation. Sheet metal edges may be sharp.

• Children and adults should be alerted to the hazards of high surface temperature and should stay away

to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children, and others may be susceptible to accidental contact burns. A physical barrier

is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,

install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the

room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and

draperies.

• Ensure you have incorporated adequate safety measures to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is off, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior to

operating the appliance.

• The appliance is a vented gas-ﬁ red appliance. Do not burn wood or other materials in the appliance.

• The appliance area must be kept clear and free from combustible materials, gasoline and other

ﬂ ammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁ ed.

• This appliance must not be connected to a chimney ﬂ ue pipe serving a separate solid fuel burning

appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system and any gas control which has

been under water.

LA VITRE CHAUDE CAUSERA

DES BRÛLURES.

NE PAS TOUCHER LA VITRE

AVANT QU’ELLE AIT REFROIDI.

NE JAMAIS LAISSER LES

ENFANTS TOUCHER LA VITRE.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

!

DANGER

!

AVERTISSEMENT

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with this appliance and

shall be installed for the protection of children and other

at-risk individuals.

Une barriére conçu à réduire le risque de brûlures

causées par le verre chaud est fourni avec l’appareil et

sera installé pour la protection des enfants et d’autres

personnes à risque.

3.1

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass

should be done by a licensed or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating to

prevent exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of the

exhaust escaping through these openings can also cause the surrounding combustible materials to overheat

and catch ﬁ re.

• Only doors / optional fronts certiﬁ ed with the unit are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all

plastic bags, these are not toys and should be kept away from children and infants.

• As with any combustion appliance, we recommend having your appliance regularly inspected and serviced

as well as having a carbon monoxide detector installed in the same area to defend you and your family

against carbon monoxide.

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.

Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or

damage to decorations, a T.V. or other electronic components.

• A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and

shall be installed.

• If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this

appliance.

• Installation and repair should be done by a qualiﬁ ed service person. The appliance should be inspected

before use and at least annually by a professional service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments,

burners and circulating air passageways of the appliance be kept clean.

!

WARNING

!

WARNING

3.1 dimensions

W415-1606 / C / 11.08.17

EN

6

general information

28"

711mm

8

7

16

"

214mm

27"

685mm

7

16

"

11mm

20"

508mm

5"

125mm

8"

202mm

60

3

16

"

1529mm

54

1

8

"

1375mm

3"

77mm

FRONT VIEW RIGHT SIDE VIEW TOP VIEW

SAFETY BARRIER

3.0 general information

3.2 hardware list

Only fasteners supplied with the appliance will be illustrated.

note:

EN

W415-1606 / C / 11.08.17

7

general information

Type Description Quantity

5/16” Long Thread Cutting Screw

1

8

2

3

4 5

1

20

4

1/2” Long Sheet Metal Screw

Lag Bolt

1/4” Flat Washer

1/4” Hex, 1/2” Long Sheet Metal Screw

39

2

3

4

5

6 1/4” Long Flat Head Screw

2

6

7

7 2 1/2” Long Sheet Metal Screw 4

3.3 general instructions

4.1

THIS GAS APPLIANCE MUST BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local

codes. Installation practices vary from region to region and it is important to know the speciﬁ cs that apply to your area, for

example in Massachusetts State:

• This product must be installed by a licensed plumber or gas ﬁ tter when installed within the commonwealth of

Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of an appliance insert or gas

log.

• The appliance off valve must be a “T” handle gas cock.

• The ﬂ exible connector must not be longer than 36 inches (0.9m).

• A carbon monoxide detector is required in all rooms containing gas ﬁ red appliances.

• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed

combustion product.

The installation must conform with local codes or, in absence of local

codes, the National Gas and Propane Installation Code CSA B149.1

in Canada, or the National Fuel Gas Code, ANSI Z223.1 / NFPA 54

in the United States. Suitable for mobile home installation if installed

in accordance with the current standard CAN/CSA Z240MH Series,

for gas equipped mobile homes, in Canada or ANSI Z223.1 and

NFPA 54 in the United States.

The appliance and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing

of that system at test pressures in excess of 1/2 psig (35 mb).

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any

pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (35 mb). When installed

with a blower or fan, the junction box must be electrically connected and grounded in accordance with local codes. In the

absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI / NFPA 70 National

Electric Code in the United States. In the case where the blower is equipped with a power cord, it must be connected into a

properly grounded receptacle. The grounding prong must not be removed from the cord plug.

The following does not apply to inserts; as long as the required clearance to combustibles is maintained, the most desirable

and beneﬁ cial location for an appliance is in the center of a building, thereby allowing the most efﬁ cient use of the heat

created. The location of windows, doors and, the trafﬁ c ﬂ ow in the room where the appliance is to be located should be

considered. If possible, you should choose a location where the vent will pass through the house without cutting a ﬂ oor or

roof joist. If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood ﬂ ooring, the

appliance shall be installed on a metal or wood panel extending the full width and depth, unless otherwise tested.

We suggest that our gas

hearth products be installed

and serviced by professionals

who are certied in the U.S.

by the National Fireplace

Institute

®

(NFI) as NFI Gas

Specialists

www.ncertied.org

!

WARNING

• Always light the pilot whether for the ﬁrst time or if the gas supply has run out, with the glass door opened

or removed.

• Provide adequate clearance for servicing and operating the appliance.

• Provide adequate ventilation.

• Never obstruct the front opening of the appliance.

• Objects placed in front of the appliance must be kept a minimum of 48” (121.9cm) from the front face of

the appliance.

• Surfaces around and especially above the appliance can become hot. Avoid contact when appliance is

operating.

• Fire risk. Explosion hazard.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at test

pressures above 1/2 PSIG. Close the manual shut-off valve before pressure testing gas line at test

pressures equal to or less than 1/2 PSIG (35mb).

• Use only Wolf Steel approved optional accessories and replacement parts with this appliance using non-

listed accessories (blowers, doors, louvres, trims, gas components, venting components, etc.) could result

in a safety hazard and will void the warranty and certiﬁcation.

• The appliance must not be operated at temperatures below freezing (32ºF / 0ºC). Allow the appliance to

warm, to above freezing prior to operation.

• This appliance has been designed and certiﬁed for indoor use only.

W415-1606 / C / 11.08.17

EN

8

general information

* When the appliance is installed at elevations above 4,500ft (1372m), and in the absence of speciﬁc recommendations from the

local authority having jurisdiction, the certiﬁed altitude input rating shall be reduced at the rate of 4% for each additional 1,000ft

(305m) above sea level.

This appliance is approved for bathroom, bedroom and bed-sitting room installations and is suitable for mobile home

installation. The natural gas model can only be installed in a mobile home that is

permanently positioned on its site and fueled with natural gas. This appliance may

be installed in an aftermarket permanently located, manufactured (mobile) home,

where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This

appliance is not convertible for use with other gases, unless a certiﬁed kit is used.

A barrier designed to reduce the risk of burns from the hot viewing glass is

provided with the appliance and must be installed.

Expansion / contraction noises during heating up and cooling down cycles are

normal and are to be expected.

This appliance is equipped with a three-prong (grounding) plug for protection against shock hazard and should be plugged

directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from the plug.

70.8%

CWHD48

70.8%

WHD48

70.8%

WHD48

Cote énergétique des foyers à gaz

Basée sur la norme CSA P.4.1-02

Modèle No.

70.8%

CWHD48

Cote énergétique des foyers à gaz

Basée sur la norme CSA P.4.1-02

Modèle No.

FRENCH:

ENGLISH:

15

EN

W415-1606 / C / 11.08.17

9

general information

FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION

AND QUALITY!

Rates and Efﬁciencies

NG P

Altitude (FT) 0-4,500* 0-4,500*

Max. Input (BTU/hr) 28,000 28,000

Min. Inlet Gas Supply Pres-

sure

4.5"

(11mb) w.c.

11"

(27mb) w.c.

Max. Inlet Gas Supply

Pressure

13"

(32mb) w.c.

13"

(32mb) w.c.

Manifold Pressure (Under

Flow Conditions)

3.5"

(9mb) w.c.

10"

(25mb) w.c.

TITLE: RATING PLATE WHD48

REVISION: B: UPDATED CSA / ANSI YEAR AND DESCRIPTION, ADDED PAGE NUMBER || 08.11.17_C.L.

DWG#: W385-2131

DATE: 06.22.16

MAX SIZE: 8.5" X 4.75"

HOLE TO BE 0.250"Ø

MATERIAL: CLASS III A-2, PERMANENT LABEL, WATERPROOF, .010MIL VELVET MATTE LEXAN AND/OR .050 HI-TEMP POLYESTER, CAPABLE OF WITHSTANDING A

MAXIMUM TEMPERATURE OF 175°F (79°C).

MIN. LETTERING FOR "NOT FOR USE WITH SOLID FUEL. ", "UN COMBUSTIBLE SOLIDE NE DOIT PAS ETRE UTILISE AVEC CELUI. " TO BE 10 POINT ARIAL, BOLD FACE,

UPPER CASE AND 2 POINT LEADING SPACING OR EQUIVALENT.

BLACK LETTERING ON WHITE BACKGROUND.

SERIAL NUMBERS TO BE ASCENDING FROM WHD48 015416

W385-2131 / B

DIRECT VENT, VENTED GAS FIREPLACES. APPROVED FOR BEDROOM, BATHROOM AND BED-SITTING

ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCORDANCE

WITH THE CURRENT STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES,

IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME CONSTRUCTION AND

SAFETY STANDARD, TITLE 24 CFR, PART 3280. WHEN THIS US STANDARD IS NOT

APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME

INSTALLATIONS, SITES AND COMMUNITIES, ANSI / NFPA 501A. THIS APPLIANCE MUST BE

INSTALLED IN ACCORDANCE WITH LOCAL CODES, IF ANY; IF NONE, FOLLOW THE CURRENT

ANSI Z223.1, OR CSA B149, INSTALLATION CODES.

FOR USE WITH BARRIER W565-0273.

FOLLOW THE INSTALLATION INSTRUCTIONS LOCATED IN THE INSTALLATION MANUAL.

FOYER À GAZ VENTILÉ. HOMOLOGUÉ POUR INSTALLATION DANS UNE CHAMBRE À COUCHER, UNE

SALLE DE BAIN ET UN STUDIO. APPROPRIÉ POUR INSTALLATION DANS UNE MAISON MOBILE SI

SON INSTALLATION CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SÉRIE DE

MAISONS MOBILES ÉQUIPÉES AU GAZ, EN VIGUEUR AU CANADA OU AUX ÉTATS-UNIS DE LA

NORME DE SÉCURITÉ ET DE CONSTRUCTION DE MAISONS MANUFACTURÉES, TITRE 24

CFR, SECTION 3280. DANS LE CAS OU CETTE NORME D'ÉTATS-UNIS NE PEUT ÊTRE

APPLIQUÉE, SE RÉFÉRER A LA NORME RELATIVE AU CRITÈRE DE MESURES DE SÉCURITÉ

CONTRE L'INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURÉS, LES

SITES ET LES COMMUNAUTÉS, ANSI/NFPA 501A. CODES. INSTALLER L’APPAREIL SELON LES

CODES OU RÈGLEMENTS LOCAUX, OU EN L’ABSENCE DE TELS RÈGLEMENTS, SELON LES

CODES D’INSTALLATION ANSI Z223.1 OU CSA-B149 EN VIGUER.

POUR UNE UTILISER AVEC

BARRIÈRE

W565-0273

. SUIVEZ LES INSTRUCTIONS D'INSTALLATION SE TROUVENT DANS LE

MANUEL D'INSTALLATION.

9700539 (WSL) 4001657 (NGZ)

4001658 (NAC) 4001659 (WUSA)

WHD48N CWHD48N MODEL CWHD48P WHD48P

0-4500FT (0-1370m) ALTITUDE / ÉLÉVATION 0-4500FT (0-1370m)

28,000 BTU/h INPUT / ALIMENTATION 28,000 BTU/h

NOT FOR USE WITH SOLID FUEL. FOR USE WITH GLASS

DOORS CERTIFIED WITH THIS APPLIANCE ONLY.

WARNING: DO NOT ADD ANY MATERIAL TO THE APPLIANCE, WHICH WILL COME IN CONTACT WITH THE FLAMES,

OTHER THAN THAT SUPPLIED BY THE MANUFACTURER WITH THE APPLIANCE.

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS / DÉGAGEMENTS MINIMAUX DES MATÉRIAUX COMBUSTIBLES *:

MANTEL / CEILING 15" MANTEAU / PLAFOND 15"

SIDES 7" CÔTÉS 7"

VENT SIDES / BOTTOM 1" CÔTÉS DE L'ÉVENT / ÉVENT INFÉRIEUR 1"

FLOOR 6" PLANCHER 6"

VENT TOP 3" ÉVENT SUPÉRIEUR 3"

* SEE INSTALLATION MANUAL FOR FURTHER INFORMATION / VOIR MANUEL D'INSTALLATION POUR PLUS

D'INFORMATION.

SEE OWNER'S INSTRUCTION MANUAL FOR MINIMUM AND MAXIMUM VENT LENGTHS.

RÉFÉRER AU MANUEL D'INSTALLATION DE PROPRIÉTAIRE POUR LES LONGUEURS D'ÉVACUATION MINIMALE

ET MAXIMALE.

UN COMBUSTIBLE SOLIDE NE DOIT PAS ÊTRE UTILISÉ

AVEC CET APPAREIL. UTILISER AVEC LES PORTES

VITRÉES HOMOLOGUÉES SEULEMENT AVEC CETTE

APPAREIL.

AVERTISSEMENT:

N’AJOUTEZ PAS À CET APPAREIL AUCUN MATÉRIAU DEVANT ENTRER EN CONTACT

AVEC LES FLAMMES AUTRE QUE CELUI QUI EST FOURNI AVEC CET APPAREIL PAR LE FABRICANT.

THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE NAPOLEON VENT KITS. SEE OWNER'S INSTALLATION

MANUAL FOR VENTING SPECIFICS. PROPER REINSTALLATION AND RESEALING IS NECESSARY AFTER SERVICING THE

VENT-AIR INTAKE SYSTEM. /

L'APPAREIL DOIT ÉVACUER SES GAZ EN UTILISANT L'ENSEMBLE D'ÉVACUATION PROPRE À NAPOLEON. RÉFÉRER AU

MANUEL D'INSTALLATION DE PROPRIÉTAIRE POUR L'ÉVACUATION PRÉCISE. IL EST IMPORTANT DE BIEN RÉINSTALLER

ET RESCELLER L'ÉVENT APRÉS AVOIR ASSURÉ LE MAINTIEN DU SYSTÉME DE PRISE D'AIR.

ELECTRICAL RATING: 115V, 60HZ. LESS THAN 12 AMPERES

SPÉCIFICATIONS ÉLECTRIQUES: 115V, 60HZ. MOINS DE 12 AMPÈRES

DECORATIVE PRODUCT: NOT FOR USE AS A HEATING APPLIANCE

PRODUIT DÉCORATIF: NE PAS UTILISER COMME APPAREIL DE CHAUFFAGE

SERIAL NUMBER/NO. DE SÉRIE: WHD48

WOLF STEEL LTD.

24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA

CERTIFIED TO / CERTIFIÉ CSA 2.22-2016 AND / ET ANSI Z21.50-2016 VENTED DECORATIVE GAS APPLIANCES / FOYER À GAZ VENTILÉ.

REDUCED INPUT / ALIMENTATION RÉDUITE

P4

19,000 BTU/h

23,000 BTU/h

70.8%70.8%

MANIFOLD PRESSURE: 3.5 INCHES W.C. (NG)

PRESSION AU COLLECTEUR: 3.5" D'UNE

COLONNE D'EAU(GN)

MIN SUPPLY PRESSURE: 4.5" W.C.(NG)

PRESSION D'ALIMENTATION MIN: 4.5" D'UNE

COLONNE D'EAU (GN)

MAX. SUPPLY PRESSURE: 13" W.C. (NG)

PRESSION D'ALIMENTATION MAX: 13" D'UNE

COLONNE D'EAU (GN)

MANIFOLD PRESSURE: 10 INCHES W.C.(P)

PRESSION AU COLLECTEUR: 10" D'UNE

COLONNE D'EAU (P)

MIN SUPPLY PRESSURE: 11" W.C. (P)

PRESSION D'ALIMENTATION MIN: 11" D'UNE

COLONNE D'EAU (P)

MAX. SUPPLY PRESSURE: 13" W.C. (P)

PRESSION D'ALIMENTATION MAX: 13" D'UNE

COLONNE D'EAU (P)

WOLF STEEL LTD.

B

PAGE 1 OF 2 B

SAMPLE

3.4 rating plate information

For rating plate location, see “INSTALLATION OVERVIEW” section.

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

The rating plate must remain with the appliance at all times. It must not be removed.

note:

7.2

!

WARNING

• Risk of ﬁ re. Maintain speciﬁ ed air space clearances to vent pipe and appliance.

• If venting is included with spacers, the vent system must be supported every 3’(0.9m) for both vertical and

horizontal runs. Use support ring assembly W010-0067 or equivalent non-combustible strapping to maintain

the minimum clearance to combustibles for both vertical and horizontal runs. Spacers are attached to the

inner pipe at predetermined intervals to maintain an even air gap to the outer pipe. This gap is required

for safe operation. A spacer is required at the start, middle, and end of each elbow to ensure this gap is

maintained. These spaces must not be removed.

This appliance uses a 5” (127mm) exhaust / 8” (203.2mm) air intake vent pipe system. Refer to the

section applicable to your installation.

For safe and proper operation of the appliance follow the venting instructions exactly. Deviation from the

minimum vertical vent length can create difﬁ culty in burner start-up and/or carboning. Under extreme vent

conﬁ gurations, allow several minutes (5-15) for the ﬂ ame to stabilize after ignition. Although not a requirement,

it is recommended for vent lengths that pass through unheated spaces (attics, garages, crawl spaces) be

insulated with the insulation wrapped in a protective sleeve to minimize condensation. Provide a means for

visually checking the vent connection to the appliance after the appliance is installed. Use a ﬁ restop, vent pipe

shield or attic insulation shield when penetrating interior walls, ﬂ oor or ceiling.

The vent terminal may be painted with a high temperature paint to match exterior colours. Use an outdoor paint

suitable for 400°F (200°C). Application and performance of paint is the consumer’s responsibility. Spot testing is

recommended.

For vent systems that provide seals on the inner exhaust ﬂ ue, only the outer air intake joints must be sealed using

a red high temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake

vent pipe joints of all other approved vent systems except for the exhaust vent pipe connection to the appliance

ﬂ ue collar which must be sealed using the black high temperature sealant Mill Pac.

When using Wolf Steel venting components, use only approved Wolf Steel rigid / ﬂ exible components with the

following termination kits: wall terminal kit GD422-1, GD422R-1, or 1/12 to 7/12 pitch roof terminal kit GD410,

8/12 to 12/12 roof terminal kit GD411, ﬂ at roof terminal kit GD412 or periscope kit GD401 (for wall penetration

below grade). With ﬂ exible venting, in conjunction with the various terminations, use either the 5 foot (1.5m) vent

kit GD420 or the 10 foot (3.1m) vent kit GD430.

For optimum ﬂ ame appearance and appliance performance, keep the vent length and number of elbows to

a minimum.

The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year

to verify that it is unobstructed and undamaged.

Rigid and ﬂ exible venting systems must not be combined. Different venting manufacturer components

must not be combined.

These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal

run is 20 feet (6.1m). The maximum allowable vertical vent length is 40 feet (12.2m). The maximum number of

vent connections is two horizontally or three vertically (excluding the appliance and the air terminal connections)

when using ﬂ exible venting.

Horizontal runs may have a 0” (0mm) rise per foot/meter however for optimum performance it is recommended

that all horizontal runs have a minimum 1/4” (21mm) rise per foot/meter using ﬂ exible venting. For safe and

proper operation of the appliance, follow the venting instructions exactly.

A terminal shall not terminate directly above a sidewalk or paved driveway which is located between two single

family dwellings and serves both dwellings. Local codes or regulations may require different clearances.

Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼”

(31.8mm) air gap all around between the inner liner and outer liner is required for safe operation.

Vent

Manufacturer

Starter Adapter Part

Number

Supplier Website

Duravent W175-0170 Wolf Steel www.duravent.com

Amerivent 5DSC-N2 American Metal www.americanmetalproducts.com

Direct Temp 5DT-AA Selkirk www.selkirkcorp.com

SuperSeal 5DNA Metal-Fab www.mtlfab.com

Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab venting

components. Minimum and maximum vent lengths, for both horizontal and vertical installations, clearances from

vent pipes to combustibles and air terminal locations as set out in this manual apply to all vent systems and

must be adhered to. For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab,

follow the installation procedure provided with the venting components. A starter adaptor must be used with the

following vent systems and may be purchased from the corresponding supplier:

If for any reason the vent air intake system is disassembled; reinstall per the instructions provided for the

initial installation.

This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing

alternate constructions, such as a chimney as part of the vent system, is not permitted.

note:

W415-1606 / C / 11.08.17

EN

10

venting requirements

4.0 venting requirements

4.1 venting lengths and components

Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab venting

components. Minimum and maximum vent lengths, for both horizontal and vertical installations, clearances from

vent pipes to combustibles and air terminal locations as set out in this manual apply to all vent systems and must

be adhered to. For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab follow the

installation procedure provided with the venting components.

A starter adaptor must be used with the following vent systems and may be purchased from the corresponding

supplier:

For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab follow the installation

procedure found on the website for your venting supplier.

For vent systems that provide seals on the inner exhaust ﬂue, only the outer air intake joints must be sealed using a red

high temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent pipe

joints of all other approved vent systems except for the exhaust vent pipe connection to the appliance ﬂue collar which

must be sealed using the black high temperature sealant Mill Pac.

When using Wolf Steel venting components, use only approved Wolf Steel rigid / ﬂexible components with the following

termination kits: wall terminal kit GD422R-2, or 1/12 to 7/12 pitch roof terminal kit GD410, 8/12 to 12/12 roof terminal

kit GD411, ﬂat roof terminal kit GD412 or periscope kit GD401 (for wall penetration below grade). With ﬂexible venting, in

conjunction with the various terminations, use either the 5 foot (1.5m) vent kit GD420 or the 10 foot (3.1m) vent kit GD430.

For optimum ﬂame appearance and appliance performance, keep the vent length and number of elbows to a

minimum.

The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify

that it is unobstructed and undamaged.

Rigid and ﬂexible venting systems must not be combined. Different venting manufacturer components must

not be combined.

These vent kits allow for either horizontal or vertical venting of the appliance. When terminating horizontally, the maximum

allowable horizontal run is 20 feet (6.1m). When terminating vertically, the maximum allowable vertical vent length is 40 feet

(12.2m). The maximum number of vent connections is two horizontally or three vertically (excluding the appliance and the

air terminal connections) when using ﬂexible venting.

Horizontal runs may have a 0” (0mm) rise per foot/meter however for optimum performance it is recommended that

all horizontal runs have a minimum 1/4” rise per foot or 21mm per meter using ﬂexible venting. For safe and proper

operation of the appliance, follow the venting instructions exactly.

A terminal shall not terminate directly above a sidewalk or paved driveway which is located between two single family

dwellings and serves both dwellings. Local codes or regulations may require different clearances.

Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼” (31.8mm)

air gap all around between the inner liner and outer liner is required for safe operation.

Vent Manufacturer

Starter Adapter Part

Number

Supplier Website

Duravent W175-0170 Wolf Steel www.duravent.com

Amerivent 5DSC-N2 American Metal www.americanmetalproducts.com

Direct Temp 5DT-AA Selkirk www.selkirkcorp.com

SuperSeal 5DDA Metal-Fab www.mtlfab.com

EN

W415-1606 / C / 11.08.17

11

venting requirements

4.2 typical vent installation

16" (40.6CM)

MINIMUM

40 FT (12M)

MAXIMUM

3 FT (1M)

MINIMUM

19 1/2"

(49.5CM)

14" (35.5CM) MAXIMUM

19 1/2" (49.5CM)

MINIMUM PLUS

RISE*

* See "VENTING" section

Appliance shown without surround.

Use the periscope kit to locate the air termination above grade. The periscope must be

installed so that when ﬁ nal grading is completed, the bottom air slot is located a minimum

12” (30.5cm) above grade. The maximum allowable vent length is 10’ (3.1m) for a

ﬁ replace and 8’ (2.4m) for a stove.

9.6B

4.3 special vent installations

4.3.1 periscope termination

12"

(30.5CM)

MINIMUM

TO GRADE

30" (76.2CM)

MINIMUM

19 1/2"

(49.5CM)

W415-1606 / C / 11.08.17

EN

12

venting requirements

4.4 vent terminal clearances

EN

W415-1606 / C / 11.08.17

13

venting requirements

NOTE: Clearances are in accordance with local installation codes and the requirements of the gas supplier.

COVERED BALCONY APPLICATIONS ††*

Q

MIN

R

MAX

R

= 3 feet

(0.9m)

= 2 x

≤ 15 feet

(4.6m)

Q

ACTUAL

R

Q

S

G

P

INSTALLATIONS

CANADA U.S.A.

A

12” (30.5cm) 12” (30.5cm) Clearance above grade, veranda porch, deck or balcony.

B

12” (30.5cm)

Δ

9” (229mm) Clearance to windows or doors that open.

C

12” (30.5cm)* 12” (30.5cm)* Clearance to permanently closed windows.

D

18”(45.7cm)** 18” (45.7cm)**

Vertical clearance to ventilated sofﬁts located above the terminal within a horizontal distance of 2’ (0.6m)

from the center line of the terminal.

E

18” (45.7cm)** 18” (45.7cm)** Clearance to unventilated sofﬁt.

F

0” (0mm) 0” (0mm) Clearance to an outside corner wall.

G

12” (30.5cm)*** 12” (30.5cm)***

Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).

12” (30.5cm)*** 12” (30.5cm)*** Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).

H

3’(0.9m) 3’(0.9m)****

Clearance to each side of the center line extended above the meter / regulator assembly to a maximum

vertical distance of 15’ (4.6m).

I

3’ (0.9m) 3’ (0.9m)**** Clearance to a service regulator vent outlet.

J

12” (30.5cm) 9” (229mm) Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.

K

6’ (1.8m) 3’ (0.9m) † Clearance to a mechanical air supply inlet.

L

7’ (2.1m) ‡ 7’ (2.1m) **** Clearance above a paved sidewalk or paved driveway located on public property.

M

12” (30.5cm)†† 12” (30.5cm)**** Clearance under a veranda, porch or deck.

N

16” (40.6cm) 16” (40.6cm) Clearance above the roof.

O

2’ (0.6m)†* 2’ (0.6m) †* Clearance from an adjacent wall including neighbouring buildings.

P

8’ (2.4m) 8’ (2.4m)

Roof must be non-combustible without openings.

Q

3’ (0.9m) 3’ (0.9m) See chart for wider wall dimensions.

R

6’ (1.8m) 6’ (1.8m)

See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an opening

between the terminal and the open side of the structure.

S

12” (30.5cm) 12” (30.5cm) Clearance under a covered balcony

Δ The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.

* Recommended to prevent condensation on windows and thermal breakage

** It is recommended to use a heat shield and to maximize the distance to vinyl clad sofﬁts.

*** The periscope requires a minimum 18 inches clearance from an inside corner.

**** This is a recommended distance. For additional requirements check local codes.

† 3 feet above if within 10 feet horizontally.

‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.

†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the ﬂoor.

†* Recommended to prevent recirculation of exhaust products. For additional requirements check local codes.

††* Permitted only if the balcony is fully open on a minimum of one side.

4.5 horizontal termination

0’

10’

15’

20’

25’

20’

30’

40’

5’

1 1/2’

(18”)

1 1/2’

(18”)

35 3/4’

(429”)

5’

1-2 elbow zone

1-3 elbow zone

1-4 elbow zone

H

V

(For vent runs that exceed the graph

parameters, a power vent is required).

V + H are measured from the centre of vent

elbows. Elbows are considered as 90º.

Two 45º elbows = One 90º elbow.

4 3/4’

(57”)

17 1/4’

(207.6”)

1-5 elbow zone

W415-1606 / C / 11.08.17

EN

14

venting requirements

4.6 vertical termination

10’

15’

20’

25’

20’

30’

40’

5’

39’

(468”)

1 elbow zone

1-2 elbow zone

1-3 elbow zone

H

V

(For vent runs that exceed the graph

parameters, a power vent is required).

V + H are measured from the centre of vent

elbows. Elbows are considered as 90º.

Two 45º elbows = One 90º elbow.

0’

1’

(12”)

3

(36”)

5’

4 3/4’

(57”)

1-4 elbow zone

1-5 elbow zone

1-6 elbow zone

EN

W415-1606 / C / 11.08.17

15

venting requirements

W415-1606 / C / 11.08.17

EN

16

installation

5.0 installation

42.1

!

WARNING

• Ensure to unpack all loose materials from inside the ﬁ rebox prior to connecting the gas and electrical supply

• If your appliance is supplied with a remote, ensure the remote receiver is in the “OFF” position prior

to connecting the gas and electrical supply to the appliance.

• For safe and proper operation of the appliance, follow the venting instructions exactly.

• The appliance exhaust ﬂ ue collar must be sealed using Mill Pac. All exhaust and intake vent pipe joints

must be sealed using red RTV high temp silicone sealant (W573-0002) (not supplied) or black high temp Mill

Pac (W573-0007) (not supplied).

• If using pipe clamps to connect rigid vent components, a minimum of 3 screws must also be used to ensure

the connection cannot slip off.

• Do not clamp the ﬂ exible vent pipe.

• Risk of ﬁ re, explosion, or asphyxiation. Improper support of the entire venting system may allow vent to sag

and separate. Use vent run supports and connect vent sections per installation instructions.

• Risk of ﬁ re, do not allow loose materials or insulation to touch the vent pipe. Remove insulation to allow for the

installation of the attic shield and to maintain clearances to combustibles.

• Do not ﬁ ll the space between the vent pipe and enclosure with any type of material. Do not pack insulation

or combustibles between ceiling ﬁ restops. Always maintain speciﬁ ed clearances around venting and ﬁ restop

systems. Install wall shields and ﬁ restops as speciﬁ ed. Failure to keep insulation or other materials away from

vent pipe may cause ﬁ re.

!

WARNING

• Risk of ﬁ re!

• In order to avoid the possibility of exposed insulation or vapour barrier coming in contact with the appliance

body, it is recommended that the walls of the appliance enclosure be “ﬁ nished” (i.e. drywall / sheetrock),

as you would ﬁ nish any other outside wall of a home. This will ensure that clearance to combustibles is

maintained within the cavity.

• Do not notch the framing around the appliance stand offs. Failure to maintain air space clearance may cause

over heating and ﬁ re. Prevent contact with sagging or loose insulation or framing and other combustible

materials. Block opening into the chase to prevent entry of blown-in insulation. Make sure insulation and

other materials are secured.

• When constructing the enclosure allow for ﬁ nishing material closer than the minimums listed must be

constructed entirely of non-combustible materials. Materials consisting entirely of steel, iron, brick, tile,

concrete, slate, glass or plasters, or any combination thereof are suitable. Materials that are reported as

passing ASTM E136, standard test method for behaviour of materials in a vertical tube furnace at 1382ºF

(750ºC) and UL763 shall be considered non-combustible materials.

• Minimum clearance to combusibles must be maintained or a serious ﬁ re hazard could result.

• The appliance requires a minimum enclosure height. Measure from the appliance base.

• If steel stud framing kits with cement board are provided, or speciﬁ ed in the installation instructions, they

must be installed.

• If speciﬁ ed in the installation instruction, ﬁ nishing must be done using a non-combustible board, ceramic tile,

marble, etc. Do NOT use wood or drywall. Any ﬁ re rated drywall is not acceptable.

When using optional ﬁ nishing accessories, the framing dimensions and ﬁ nishing materials may differ from

what is outlined in the section below; refer to the leaﬂ et instructions supplied in the accessory kit for speciﬁ c

framing and ﬁ nishing speciﬁ cations.

44.1

note:

EN

W415-1606 / C / 11.08.17

17

installation

A. Level and afﬁx the mounting ‘template’ to the wall at the desired location and height. The centre of the

vent pipe must be centered between wall studs.

B. Using the ‘template’, mark the holes for the vent, gas and electrical inlets, and mounting screw locations

(must be into studs). See “MINIMUM CLEARANCES TO COMBUSTIBLES” section.

NOTE : Use the appropriate cutout on the mounting ‘template’ for combustible material.

C. Remove the mounting ‘template’ from the wall and cut/drill the required holes as marked.

D. Form the vent shield until the four screw holes overlap then secure from the inside out. (FIG. 1)

NOTE : Securing from the outside in will puncture venting.

E. Bend the four tabs on the ﬁrestop spacer outwards. Slide the vent shield into the ﬁrestop spacer aligning

the holes within the tabs and secure. (FIG. 2)

F. The vent shield and ﬁrestop spacer have been designed to accommodate a maximum wall depth of 14"

(35.6cm). The vent shield must extend the full depth of the combustible wall. Trim the vent shield to suit

as necessary.

G. Apply a bead of caulking (not supplied) to the ﬂange perimeter and wings of the ﬁrestop plate. Install the

wall mounting plate assembly with the vent shield into the wall. (FIG. 3)

NOTE : Ensure the assembly is levelled.

H. Look through slotted holes on the wall mounting plate for pre-marked stud locations and secure wall

mounting plate assembly using a minimum of four screws (minimum one screw per corner must be

mounted to a wall stud). (FIG. 4)

NOTE : For typical stud wall with drywall installation, fasteners are provided and must engage

into frame/studs.

I. See the following sections up to the “FINISHING” section for venting and mounting instructions.

REAR VIEW

CAULKING

5.1 mounting plate installation (for typical drywall construction)

FIG.1 FIG.2

FIG.3 FIG.4

TYPE 1 (X4) TYPE 1 (X4)

TYPE 4 (X4)TYPE 3 (X4)

Bottom of appliance must maintain 6” clearance

to combustible. See “MINIMUM CLEARANCE TO

COMBUSTIBLES” section.

NOTE : For ease of installation, we recommend

installing fasteners into the 4 outer slots.

Fasteners must be secured to a stud.

W415-1606 / C / 11.08.17

EN

18

installation

5.2 mounting plate installation (for concrete)

A. Level and afﬁx the mounting ‘template’ to the wall at the desired location and height.

B. Using the ‘template’, mark the holes for the vent, gas and electrical inlets, and wall anchor locations. See

“MINIMUM CLEARANCES TO COMBUSTIBLES” section.

NOTE : Use the appropriate cutout on the mounting ‘template’ for non-combustible material.

C. Remove the mounting ‘template’ from the wall and cut/drill the required holes as marked.

D. Remove the four fasteners that secure the ﬁrestop spacer assembly (complete with the wall plate) from

the wall mounting plate. (FIG. 1)

E. Place the wall mounting plate against the non-combustible wall and align the wall mounting plate hole

with the vent hole. Level the wall mounting plate. Once leveled, secure the wall mounting plate to the wall

through the dimpled holes using four fasteners (not supplied).

NOTE : For non-combustible installation, wall anchors (not supplied) will be required.

F. Look through slotted holes on the wall mounting plate for pre-marked mounting locations and secure wall

mounting plate using a minimum of one fastener per corner (not supplied). (FIG. 2)

G. See the following sections up to the “FINISHING” section for venting and mounting instructions.

FIG.2

5.3 using ﬂexible vent components

FIG.1

17.1

For safe and proper operation of the appliance, follow the venting instructions

exactly.

The vent system must be supported approximately every 3 feet (0.9m) for

both vertical and horizontal runs. Use Wolf Steel Ltd. support ring assembly

or equivalent noncombustible strapping to maintain the minimum clearance to

combustibles for both vertical and horizontal runs.

All inner ﬂ ex pipe and outer ﬂ ex pipe joints may be sealed using high temperature

red RTV silicone W573-0002 (not supplied) or the high temperature sealant W573-

0007 Mill Pac (not supplied). However, the high temperature sealant W573-0007

Mill Pac (not supplied) must be used on the joint connecting the inner ﬂ ex pipe and

the exhaust ﬂ ue collar.

Use only approved ﬂ exible vent pipe kits marked:

“Wolf Steel Approved Venting” or “E2” as identiﬁ ed by the stamp only on the ﬂ ex pipes.

Elbow

Spacers

• Do not allow the inner ﬂ ex pipe to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight.

• Spacers are attached to the inner ﬂ ex pipe at predetermined intervals to maintain an even air gap to the outer

ﬂ ex pipe. This gap is required for safe operation. A spacer is required at the start, middle, and end of each

elbow to ensure this gap is maintained. These spacers must not be removed.

!

WARNING

EN

W415-1606 / C / 11.08.17

19

installation

This application occurs when venting through a roof. Installation kits for

various roof pitches are available from your authorized dealer / distributor.

See accessories to order speciﬁ c kits required.

A. Determine the air terminal location, cut and frame a square opening as

illustrated in the ceiling and the roof to provide the minimum 1" (25mm)

clearance between the vent pipe and any combustible material. Try to

center the vent pipe location midway between two joists to prevent

having to cut them. Use a plumb bob to line up the center of the

openings. A vent pipe shield will prevent any materials such as

insulation, from ﬁ lling up the 1" (25mm) air space around the pipe.

Nail headers between the joist for extra support.

B. Apply a bead of caulking (not supplied) to the framework or to the

Wolf Steel vent pipe shield plate or equivalent (in the case of a ﬁ nished

ceiling), and secure over the opening in the ceiling. A ﬁ restop must be placed

on the bottom of each framed opening in a roof or ceiling that the venting

system passes through. Apply a bead of caulking all around and place a

ﬁ restop spacer over the vent shield to restrict cold air from being drawn into the

room or around the ﬁ replace. Ensure that both spacer and shield maintain the required

clearance to combustibles. Once the vent pipe is installed in its ﬁ nal position, apply

Mill Pac sealant (W573-0007) (not supplied) or red RTV silicone (W573-0002) (not

supplied) between the pipe and the ﬁ restop assembly.

C. In the attic, slide the vent pipe collar down to cover up the open end of the shield and

tighten. This will prevent any materials, such as insulation, from ﬁ lling up the 1" (25mm)

air space around the pipe.

21.1B

CAULKING

VENT PIPE

SHIELD

FIRESTOP

UNDERSIDE OF

JOIST

VENT

PIPE

COLLAR

VENT

PIPE

SHIELD

8”

A. Stretch the inner ﬂ ex pipe to the required length taking into account

the additional length needed for the ﬁ nished wall surface. Apply

a heavy bead of the Mill Pac sealant (W573-0007) (not

supplied) to the inner sleeve of the air terminal. Slip the

vent pipe a minimum of 2” (50.8mm) over the inner

sleeve of the air terminal and secure with a minimum

of 3 screws.

B.

Using the outer ﬂ ex pipe, slide over the outer

combustion air sleeve of the air terminal and secure with

a minimum of 3 screws. Seal using red RTV silicone

(W573-0002) (not supplied).

C. Insert the vent pipes through the ﬁ restop maintaining the

required clearance to combustibles. Holding the air terminal

(lettering in an upright, readable position), secure to the exterior

wall and make weather tight by sealing with caulking (not

supplied).

D. If more vent pipe needs to be used to reach the ﬁ replace,

couple them together as illustrated. The vent system must be

supported approximately every 3 feet (0.9m) for both vertical

and horizontal runs. Use non-combustible strapping to

maintain the minimum clearance to combustibles.

The air terminal mounting plate may be recessed into the exterior wall

or siding no greater than the depth of its return ﬂ ange.

23.1D

SCREWS

2" (50.8mm) OVERLAP

OUTER FLEX PIPE

INNER FLEX

PIPE

HIGH TEMPERATURE

SEALANT

CAULKING

(SUPPLIED)

Hi-Temp Sealant

Screws

Inner Coupler

Outer Coupler

Outer Flex

Pipe

Inner Flex

Pipe

Outer Flex

Pipe

HI-TEMP

SEALANT

ADD FASTENER TYPE

A.

Install the inner ﬂ ex pipe to the ﬁ replace. Secure with

a minimum 3 screws. Seal the joint and screw holes

using Mill Pac sealant (W573-0007) (not supplied).

B.

Install the outer ﬂ ex pipe to the ﬁ replace. Secure with

a minimum of 3 screws. Seal the joints using red RTV

silicone (W573-0002) (not supplied).

28.4C

HIGH

TEMPERATURE

SEALANT

SCREWS

1

/2” OVERLAP

(38.1mm)

ADD FASTENER TYPE

TYPE 7 (X4)

TYPE 5 (X6)

5.3.1 appliance vent connection

5.3.2 vertical installation

5.3.3 horizontal air terminal installation

W415-1606 / C / 11.08.17

EN

20

installation

5.3.4 vertical air terminal installation (ﬂexible)

A. Stretch the inner ﬂ ex pipe to the required length taking into account

the additional length needed for the ﬁ nished wall surface. Apply

a heavy bead of the Mill Pac sealant (W573-0007) (not

supplied) to the inner sleeve of the air terminal. Slip the

vent pipe a minimum of 2” (50.8mm) over the inner

sleeve of the air terminal and secure with a minimum

of 3 screws.

B. Using the outer ﬂ ex pipe, slide over the outer

combustion air sleeve of the air terminal and secure with

a minimum of 3 screws. Seal using red RTV silicone

(W573-0002) (not supplied).

C. Insert the vent pipes through the ﬁ restop maintaining the

required clearance to combustibles. Holding the air terminal

(lettering in an upright, readable position), secure to the exterior

wall and make weather tight by sealing with caulking (not

supplied).

D. If more vent pipe needs to be used to reach the ﬁ replace,

couple them together as illustrated. The vent system must be

supported approximately every 3 feet (0.9m) for both vertical

and horizontal runs. Use non-combustible strapping to

maintain the minimum clearance to combustibles.

The air terminal mounting plate may be recessed into the exterior wall

or siding no greater than the depth of its return ﬂ ange.

23.1D

SCREWS

2" (50.8mm) OVERLAP

OUTER FLEX PIPE

INNER FLEX

PIPE

HIGH TEMPERATURE

SEALANT

CAULKING

(SUPPLIED)

Hi-Temp Sealant

Screws

Inner Coupler

Outer Coupler

Outer Flex

Pipe

Inner Flex

Pipe

Outer Flex

Pipe

HI-TEMP

SEALANT

ADD FASTENER TYPE

A. Fasten the roof support to the roof using 6 screws. The roof support is

optional. In this case, the venting is to be adequately supported using

either an alternate method suitable to the authority having jurisdiction or

the optional roof support.

B. Stretch the inner ﬂ ex pipe to the required length. Slip the inner ﬂ ex

pipe a minimum of 2” (51mm) over the inner pipe of the air terminal

connector and secure with a minimum of three screws, when 4/7, 5/8

and 3/5 venting is used and a minimum of six screws when using 8/10

or 8/11 venting. Seal using a heavy bead of red RTV silicone (W573-

0002) (not supplied).

C. Repeat using the outer ﬂ ex pipe, using a heavy bead of red RTV

silicone (W573-0002) (not supplied) and a minimum of three screws,

when 4/7, 5/8 and 3/5 venting is used and a minimum of six screws

when using 8/10 or 8/11 venting.

D. Thread the air terminal connector / vent pipe assembly down through

the roof. The air terminal must be positioned vertically and plumb.

Attach the air terminal connector to the roof support, ensuring that the

top of the air terminal is 16” (40.6cm) above the highest point that it

penetrates the roof.

E. Remove nails from the shingles, above and to the sides of the air

terminal connector. Place the ﬂ ashing over the air terminal connector

leaving a min. 3/4” (19mm) of the air terminal connector showing above

the top of the ﬂ ashing. Slide the ﬂ ashing underneath the sides and

upper edge of the shingles. Ensure that the air terminal connector is

properly centered within the ﬂ ashing, giving a 3/4” (19mm) margin all

around. Fasten to the roof. Do not nail through the lower portion of the

ﬂ ashing. Make weather-tight by sealing with caulking. Where possible,

cover the sides and top edges of the ﬂ ashing with rooﬁ ng material.

F. Aligning the seams of the terminal and air terminal connector, place the

terminal over the air terminal connector making sure the vent pipe goes

into the hole in the terminal. Secure with a minimum of three screws,

when 4/7, 5/8 and 3/5 venting is used and a minimum of six screws

when using 8/10 or 8/11 venting.

G. Apply a heavy bead of weatherproof caulking 2” (51mm) above the

ﬂ ashing. Install the storm collar around the air terminal and slide down

to the caulking. Tighten to ensure that a weather-tight seal between the

air terminal and the collar is achieved.

H. If more vent pipe needs to be used to reach the appliance, see “horizontal

air terminal installation” section.

18.5

Roof Support

Inner Flex Pipe

Inner Pipe

Red RTV

Silicone

(W572-0002)

Air

Terminal

Connector

Outer Flex Pipe

Storm Collar

Flashing

Caulking

Weather

Sealant

2” (51mm)

Air Inlet

Base

!

WARNING

• Maintain a minimum 2” (51mm) space between the air inlet base and the storm collar.

NOTE: Fastening hardware provided with appropriate roof terminal and liner kits.

La page charge ...

NAPOLEON Plazmafire 48 Le manuel du propriétaire

Ce manuel convient également à

NAPOLEON Plazmafire 48 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents