NAPOLEON GDI-30NSB Le manuel du propriétaire

EN

W415-1365 / A / 07.28.16

FR

PG

33

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE

INSTALLATION AND

OPERATING INSTRUCTIONS

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)720-9081 • www.napoleonﬁ replaces.com • [email protected]

1.28F

$10.00

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

!

DANGER

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed for the protection of children

and other at-risk individuals.

SAFETY INFORMATION

!

WARNING

- Do not store or use gasoline or other ﬂ ammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

ﬁ re department.

- Installation and service must be performed by a

qualiﬁ ed installer, service agency or the supplier.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless a

certiﬁ ed kit is used.

If the information in these instructions

are not followed exactly, a ﬁ re or

explosion may result causing property

damage, personal injury or loss of life.

CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.

Decorative Product: Not for use as a heating appliance.

SAFETY BARRIER

SHOWN WITH GIFK6 FLASHING & FPGI30-K FACEPLATE

CONFORMS TO AMERICAN NATIONAL STANDARDS: ANSI Z21.50, CERTIFIED TO CANADIAN CSA 2.22 FOR VENTED GAS FIREPLACES.

GDI-30N

NATURAL GAS

GDI-30P

PROPANE

TABLE OF CONTENTS

1.0 INSTALLATION OVERVIEW 3

2.0 INTRODUCTION 4

2.1 DIMENSIONS 5

2.2 MINIMUM CLEARANCE TO COMBUSTIBLES 5

2.3 GENERAL INSTRUCTIONS 6

2.4 GENERAL INFORMATION 7

2.5 RATING PLATE INFORMATION 8

3.0 INSTALLATION 9

3.1 LEVELLING THE APPLIANCE 9

3.2 CHIMNEY CONNECTION 10

3.3 GAS INSTALLATION 11

3.4 OPTIONAL WALL SWITCH 11

4.0 FINISHING 12

4.1 MINIMUM MANTEL CLEARANCES 12

4.2 SAFETY SCREEN REMOVAL AND INSTALLATION 13

4.3 DOOR REMOVAL AND INSTALLATION 14

4.4 GRATE INSTALLATION 14

4.5 LOG PLACEMENT 15

4.6 OPTIONAL CHARCOAL EMBERS 16

4.7 GLOWING EMBERS 16

4.8 LOGO PLACEMENT 16

5.0 BLOWER REPLACEMENT 17

6.0 OPERATION 18

7.0 ADJUSTMENTS 19

7.1 PILOT BURNER ADJUSTMENT 19

7.2 VENTURI ADJUSTMENT 19

7.3 FLAME CHARACTERISTICS 19

8.0 MAINTENANCE 20

8.1 CARE OF GLASS 21

8.2 ANNUAL MAINTENANCE 21

8.3 DOOR GLASS REPLACEMENT 22

9.0 REPLACEMENTS 22

9.1 OVERVIEW 23

9.2 VALVE TRAIN ASSEMBLY 24

10.0 ACCESSORIES 25

11.0 TROUBLESHOOTING (ELECTRONIC) 26

12.0 TROUBLESHOOTING (MILLIVOLT) 28

13.0 WARRANTY 30

14.0 SERVICE HISTORY 31

W415-1365 / A / 07.28.16

2

EN

NOTE: changes, other than editorial, are denoted by a vertical line in the margin.

NOTE: The camera icon indicates video tutorials are available as additional reference, visit

http://http://mynapoleon.napoleonproducts.com/download/index/44/1

W415-1365 / A / 07.28.16

3

EN

1.0 INSTALLATION OVERVIEW

SAFETY BARRIER

Venting, see “INSTALLATION

- CHIMNEY CONNECTION”

section.

Logs, see “FINISHING

- LOG PLACEMENT”

section.

Grate, see “FINISHING -

GRATE INSTALLATION”

section.

Rating Plate, see

“RATING PLATE

INFORMATION”

section.

Door, see “SAFETY SCREEN

REMOVAL / INSTALLATION” &

“DOOR REMOVAL /

INSTALLATION” section.

Batteries must be disposed of according to the local laws and regulations. Some batteries may be

recycled, and may be accepted for disposal at your local recycling center. Check with your municipality

for recycling instructions.

W415-1365 / A / 07.28.16

4

EN

2.0 INTRODUCTION

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.

• ANY CHANGES TO THIS APPLIANCE OR ITS CONTROLS CAN BE DANGEROUS AND ARE PROHIBITED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to

operating instructions could cause ﬁ re or injury.

• Risk of ﬁ re or asphyxiation do not operate appliance with ﬁ xed glass removed.

• Do not connect 110 volts to the control valve.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges may be sharp.

• Do not burn wood or other materials in this appliance.

• Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns

or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is

recommended if there are at risk individuals in the house. To restrict access to an appliance or stove, install an

adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and away from hot

surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot surfaces. These

screens and guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior to operating the

appliance.

• The appliance is a vented gas-ﬁ red appliance. Do not burn wood or other materials in the appliance.

• The appliance area must be kept clear and free from combustible materials, gasoline and other ﬂ ammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁ ed.

• This appliance must not be connected to a chimney ﬂ ue pipe serving a separate solid fuel burning appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician to inspect the appliance

and to replace any part of the control system and any gas control which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be done by a

licensed or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating to prevent exhaust fumes

containing carbon monoxide, from entering into the home. Temperatures of the exhaust escaping through these openings can also

cause the surrounding combustible materials to overheat and catch ﬁ re.Only doors / optional fronts certiﬁ ed with the unit are to be

installed on the appliance.

• Only doors / optional fronts certiﬁ ed with the unit are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic bags, these

are not toys and should be kept away from children and infants.

• As with any combustion appliance, we recommend having your appliance regularly inspected and serviced as well as having a

Carbon Monoxide Detector installed in the same area to defend you and your family against Carbon Monoxide.

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance. Elevated temperatures

on the wall or in the air above the appliance can cause melting, discolouration or damage to decorations, a T.V. or other electronic

components.

• A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be

installed.

• If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this appliance.

• Installation and repair should be done by a qualiﬁ ed service person. The appliance should be inspected before use and

at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from

carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of

the appliance be kept clean.

• The millivolt version of this appliance uses and requires a fast acting thermocouple. Replace only with a fast acting thermocouple

supplied by Wolf Steel Ltd.

3.1E

!

WARNING

W415-1365 / A / 07.28.16

5

EN

2.1 DIMENSIONS

23 1/8"

587mm

21 3/4"

552mm

ø

3"

76mm

13 3/4"

349mm

5 1/4"

133mm

1 3/8"

35mm

18 3/4"

476mm

13 3/4"

349mm

11 1/8"

283mm

30 1/16"

764mm

19 5/8"

499mm

27 1/2"

692mm

GAS INLET

This appliance must be recessed into a vented noncombustible wood-burning appliance (prefabricated or

masonry) only. The minimum appliance opening size in which the appliance is to be installed is:

HEIGHT 22" (559mm) WIDTH 28" (711mm) DEPTH 18" (457mm)

The minimum allowable chimney ﬂ ue size is 6" (152mm) round.

The minimum distance, from the bottom of a combustible mantle projecting 3" (76mm) maximum from the

wall to the top of the louvre opening, is 12" (305mm).

2.2 MINIMUM CLEARANCE TO COMBUSTIBLES

W415-1365 / A / 07.28.16

6

EN

2.3 GENERAL INSTRUCTIONS

4.12A

THIS GAS APPLIANCE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to

conform with local codes. Installation practices vary from region to region and it is important to know the

speciﬁ cs that apply to your area, for example in Massachusetts State:

• This product must be installed by a licensed plumber or gas ﬁ tter when installed within the commonwealth

of Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of an appliance

insert or gas log.

• The appliance off valve must be a “T” handle gas cock.

• The ﬂ exible connector must not be longer than 36 inches (914mm).

• A Carbon Monoxide detector is required in all rooms containing gas ﬁ red appliances.

• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent

sealed combustion product.

The installation must conform with local codes or, in

absence of local codes, the National Gas and Propane

Installation Code CSA B149.1 in Canada, or the National

Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United

States. Suitable for mobile home installation if installed in

accordance with the current standard CAN/CSA Z240MH

Series, for gas equipped mobile homes, in Canada or

A

NSI Z223.1 and NFPA 54 in the United States.

Some appliances have optional fans or blowers. If an optional fan or blower is installed, the junction box must

be electrically connected and grounded in accordance with local codes, use the current CSA C22.1 Canadian

Electrical Code in Canada or the ANSI/NFPA 70 National Electrical code in the United States.

We suggest that our gas

hearth products be installed

and serviced by professionals

who are certied in the U.S.

by the National Fireplace

Institute

®

(NFI) as NFI Gas

Specialists

www.ncertied.org

ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT,

WITH THE GLASS DOOR OPENED OR REMOVED.

PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.

PROVIDE ADEQUATE VENTILATION.

NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.

OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48” (1219mm)

FROM THE FRONT FACE OF THE APPLIANCE.

SURFACES AROUND AND ESPECIALLY ABOVE THE APPLIANCE CAN BECOME HOT. AVOID CONTACT

WHEN THE APPLIANCE IS OPERATING.

FIRE RISK. EXPLOSION HAZARD.

HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE PRESSURE TESTING GAS

LINE AT TEST PRESSURES ABOVE 1/2 PSIG. CLOSE THE MANUAL SHUT-OFF VALVE BEFORE PRESSURE

TESTING GAS LINE AT TEST PRESSURES EQUAL TO OR LESS THAN 1/2 PSIG (35mb).

USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH THIS APPLIANCE.

USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS COMPONENTS, VENTING

COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICATION.

!

WARNING

W415-1365 / A / 07.28.16

7

EN

2.4 GENERAL INFORMATION

FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND

QUALITY!

GDI-30

NG LP

Altitude (FT) 0-4,500 0-4,500

Max. Input (BTU/HR) 24,500 24,500

Max. Output (BTU/HR) 20,825 20,825

Efﬁ ciency (w/the fan on) 85% 85%

A.F.U.E. (maximum value) 82% 82%

Min. Inlet Gas Supply Pressure 4.5" (11mb) Water Column 11" (27mb) Water Column

Max. Inlet Gas Supply Pressure 7" (17mb) Water Column 13" (32mb) Water Column

Manifold Pressure (Under Flow Conditions) 3.5" (9mb) Water Column 10" (25mb) Water Column

When the appliance is installed at elevations above 4,500ft (1372m), and in the absence of speciﬁ c

recommendations from the local authority having jurisdiction, the certiﬁ ed high altitude input rating shall be

reduced at the rate of 4% for each additional 1,000ft (305m). Expansion / contraction noises during heating

up and cooling down cycles are normal and to be expected.

This appliance is not approved for closet or recessed installations. It

is approved for bathroom, bedroom and bed-sitting room installations

and is suitable for mobile homes. The natural gas model is suitable for

installation in a mobile home that is permanently positioned on its site

and fuelled with natural gas.

A barrier designed to reduce the risk of burns from the hot viewing

glass is provided with the appliance and must be installed.

64.5%

GDI-30

W415-1365 / A / 07.28.16

8

EN

2.5 RATING PLATE INFORMATION

INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to

the model, venting and gas type of the appliance.

For rating plate location, see “INSTALLATION OVERVIEW” section.

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

0-4500FT 0-4500FT

24,500 BTU/h 24,500 BTU/h

15,000 BTU/h 19,000 BTU/h

W385-1983

CE FOYER UTILISE ET REQUIERT UN THERMOCOUPLE À ACTION RAPIDE. REMPLACEZ UNIQUEMENT AVEC UN

THERMOCOUPLE À ACTION RAPIDE DE WOLF STEEL LTÉE. HOMOLOGUE POUR INSTALLATION DANS

UNE CHAMBRE A COUCHER, UNE SALLE DE BAIN ET UN STUDIO. APPROPRIE POUR INSTALLATION DANS

UNE MAISON MOBILE SI SON INSTALLATION CONFORME AUX EXIGENCES DE LA NORME CAN/CSA

Z240MH SERIE DE MAISONS MOBILES EQUIPEES AU GAZ, EN VIGUEUR AU CANADA A OU AUX

ETATS-UNIS DE LA NORME DE SECURITE ET DE CONSTRUCTION DE MAISONS MANUFACTUREES, TITRE

24 CFR, SECTION 3280. DANS LE CAS OU CETTE NORME D’ETATS-UNIS NE PEUT ETRE APPLIQUEE, SE

REFERER A LA NORME RELATIVE AUCRITERE DE MESURES DE SECURITE CONTRE L’INCENDIE POUR

LES INSTALLATIONS DANS LES MAISONS MANUFACTURERS, LES SITES ET LES COMMUNAUTES,

ANSI/NFPA 501A.

WOLF STEEL LTD.

24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA

CONFORMS TO / CONFORME AUX: ANSI Z21.50-2014, CERTIFIED TO / CERTIFIE CSA 2.22-2014 VENTED GAS FIREPLACE / FOYER À GAZ VENTILÉ.

THIS FIREPLACE USES AND REQUIRES A FAST ACTING THERMOCOUPLE. REPLACE ONLY WITH A FAST ACTING

THERMOCOUPLE SUPPLIED BY WOLF STEEL LTD. APPROVED FOR BEDROOM, BATHROOM &

BEDSITTING ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALLATION IF INSTALLED IN

ACCORDANCE WITH THE CURRENT STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE

HOMES, IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME CONSTRUCTION AND

SAFETY STANDARD, TITLE 24 CFR, PART 3280. WHEN THIS US STANDARD IS NOT APPLICABLE USE THE

STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLATIONS, SITES AND

COMMUNITIES, ANSI / NFPA 501A.

MANIFOLD PRESSURE: 3.5” W.C. (NG)

PRESSION AU COLLECTEUR: 3,5” D’UNE

COLONNE D’EAU (GN)

MIN. SUPPLY PRESSURE: 4.5” W.C. (NG)

PRESSION D’ALIMENTATION MIN: 4,5” D’UNE

COLONNE D’EAU (GN)

MAX. SUPPLY PRESSURE: 7” W.C. (NG)

PRESSION D’ALIMENTATION MAX: 7” D’UNE

COLONNE D’EAU (GN)

MANIFOLD PRESSURE: 10” W.C. (LP)

PRESSION AU COLLECTEUR: 10” D’UNE

COLONNE D’EAU (P)

MIN. SUPPLY PRESSURE: 11” W.C. (LP)

PRESSION D’ALIMENTATION MIN: 11” D’UNE

COLONNE D’EAU (P)

MAX. SUPPLY PRESSURE: 13” W.C. (LP)

PRESSION D’ALIMENTATION MAX: 13” D’UNE

COLONNE D’EAU (P)

WARNING: DO NOT ADD ANY MATERIAL TO THE APPLIANCE, WHICH WILL COME IN CONTACT WITH THE

FLAMES, OTHER THAN THAT SUPPLIED BY THE MANUFACTURER WITH THE APPLIANCE.

DECORATIVE PRODUCT: NOT FOR USE AS A HEATING APPLIANCE

ELECTRICAL RATING: 115V 1.5AMP 60HZ

THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE WOLF STEEL VENT KITS. SEE OWNERS

INSTALLATION MANUAL FOR VENTING SPECIFICS. PROPER REINSTALLATION AND RESEALING IS NECESSARY

AFTER SERVICING THE VENT-AIR INTAKE SYSTEM.

WARNING: FOR INSTALLATION INTO A VENTED NON-COMBUSTIBLE FIREPLACE ONLY. THE MINIMUM

FIREPLACE SIZE IS: HEIGHT 21.75”, DEPTH 18”, WIDTH 28”. THE MINIMUM INSIDE FLUE SIZE IS 7”. THE

MINIMUM DISTANCE, FROM THE BOTTOM OF A COMBUSTIBLE MANTEL PROJECTING A MAXIMUM 3” FROM THE

WALL TO THE TOP OF THE UNIT IS 12”. SEE OWNERS MANUAL FOR GREATER EXTENSIONS.

AVERTISSEMENT: N’AJOUTEZ PAS A CET APPAREIL AUCUN MATERIAU DEVANT ENTRER EN CONTACT AVEC LES

FLAMMES AUTRE QUE CELUI QUI EST FOURNI AVEC CET APPAREIL PAR LE FABRICANT.

PRODUIT DÉCORATIF: NE PAS UTILISER COMME APPAREIL DE CHAUFFAGE.

CLASS: 115V 1,5AMP 60HZ

L’APPAREIL DOIT EVACUER SES GAZ EN UTILISANT L’ENSEMBLE D’EVACUATION PROPRE A WOLF STEEL. REFERER

AU MANUEL D’INSTALLATION DE PROPRIETAIRE POUR L’EVACUATION PRECISE. IL EST IMPORTANT DE BIEN

REINSTALLER ET RESCELLER L’EVENT APRES AVOIR ASSURE LE MAINTIEN DU SYSTEME DE PRISE D’AIR.

ATTENTION: POUR INSTALLATION DANS UN FOYER VENTILE EN MACONNERIE. LES DIMENSIONS MINIMUMS SONT:

HAUTEUR 21,75”, PROFONDEUR 18”, LARGEUR 28”. LE DIAMETRE INTERIEUR MINIMUM DE CONDUIT D’EVACUATION

EST 7”. LA DISTANCE MINIMALE, DU BAS DU MANTEAU COMBUSTIBLE FORMANT UNE PROJECTION MAXIMALE DE 3”

DU MUR AU DESSUS DE LA GARNITURE NORMALE EST 12” REFERER AU MANUEL D’INSTALLATION POUR DES

EXTENSIONS PLUS GRANDES.

9700539 (WSL) 4001657 (NGZ)

4001658 (NAC) 4001659 (WUSA)

NATURAL GAS/ GAZ MODEL

PROPANE MODEL

GDI-30N

CDI-30N

GDI-30P

CDI-30P

MINIMUM AND MAXIMUM VERTICAL VENT LENGTHS

ARE 10 FEET AND 35 FEET RESPECTIVELY.

LES LONGUEURS VERTICALES MINIMALES ET MAXIMALES

SONT 10 PIEDS ET 35 PIEDS RESPECTIVEMENT.

64.5%

NOT FOR USE WITH SOLID FUEL

MINIMUM AND MAXIMUM VERTICAL VENT LENGTHS

ARE 10 FEET AND 35 FEET RESPECTIVELY.

LES LONGUEURS VERTICALES MINIMALES ET MAXIMALES

SONT 10 PIEDS ET 35 PIEDS RESPECTIVEMENT.

UN COMBUSTIBLE SOLIDE NE DOIT PAS ETRE UTILISE AVEC

CET APPAREIL

64.5%

ALTITUDE / ELEVATION

INPUT / ALIMENTATION

REDUCED INPUT /

ALIMENTATION REDUITE

P4

FOR USE WITH GLASS DOORS CERTIFIED WITH THIS

UNIT ONLY.

FOR USE ONLY WITH BARRIER W565-0179.

FOLLOW THE INSTALLATION INSTRUCTIONS

LOCATED IN THE INSTALLATION MANUAL.

UTILISER AVEC LES PORTES VITREES HOMOLOGUEES

SEULEMENT AVEC CETTE UNITE.

POUR UNE UTILISER

SEULMENT AVEC BARRIÈRE W565-0179. SUIVEZ LES

INSTRUCTIONS D'INSTALLATION SE TROUVENT DANS

LE MANUEL D'INSTALLATION

.

SERIAL NUMBER / NO. DESERIE

GDI-30

SAMPLE

N

SONS MOONS M

RME DE SECURME DE SEC

3280. DANS LE CAS 3280. DANS

A NORME RELATIVE AUCRNORME RELATIVE AUC

ALLATIONS DANS LES MAISONIONS DANS LES MAIS

CE, WHICH WILL COME IN CONTACT WITH THEICH WILL COME IN CONTACT WITH THE

FACTURER WITH THE APPLIANCEWITH THE APPLIAN

.

ING APPLIANCE

THE APPROPRIATE WOLF STEEL VENT KITS. SETHE APPROPRIATE WOLF STEEL VENT KITS. SE

SPECIFICS. PROPER REINSTALLATION AND RES

ECIFICS. PROPER REINSTALLATIO

KE SYSTEM.

SYSTEM.

NTED NON-COMBUSTIBLE FIREPLAC

NTED NON-COMBUSTIBLE FIREPLA

18”, WIDTH 28”. THE MINIMUM 8”, WIDTH 28”. THE MINIMUM

A COMBUSTIBLE MANTELMBUSTIBLE MANT

NERS MANUAL FONERS MANUAL FO

001657 (NGZ)

4001659 (WUSA)400

L

PROPANE MODEROPANE MOD

G

DI-

30

P

30P

LE

E

ERTICAL VENT LENGTHS RTICAL VENT LENGTHS

EET RESPECTIVELY. RESPECTIVELY.

VERTICALES MINIMALES ET MAXIMALES ES MINIMALES ET MAXIMALE

S ET 35 PIEDS RESPECTIVEMENT.ET 35 PIEDS RESPECTIVEMENT.

/ ELEVATION/ ELEVATION

T / ALIMENTATION/ ALIMENTATION

REDUCED INPUT /EDUCE

ALIMENTATION

REDUITEALIMENTATION REDUITE

P4P4

UTILISUTILI

SE

W415-1365 / A / 07.28.16

9

EN

3.0 INSTALLATION

3.1 LEVELLING THE APPLIANCE

Move the appliance close to its ﬁ nal position inside the wood-burning appliance. This appliance is equipped

with 4 levelling screws located in the four inside corners beneath the log support. Level using the levelling

screws to eliminate rocking or excessive noise when the fan is in operation. Once the appliance is level, move

it partially into place within the appliance to allow for all connections to be made. It is not practical to level the

appliance once it has been installed. Determine the required depth prior to installing the appliance and adjust

the four levelling screws accordingly.

68.4B

Clean out ashes from the inside of the wood-burning appliance. Make sure that the chimney and wood-burning

appliance are in a clean and sound condition and constructed of non-combustible materials. If necessary have

any repair work done by a qualiﬁ ed person before installing the insert. Remove the existing appliance damper

or lock into an open position.

Using screws, attach the appliance warning tag

to the inside of the ﬁ rebox of the appliance into

which the insert is being installed.

The sheet-metal parts of the appliance, in which

the gas appliance insert is to be installed, must

not be cut.

If the wood-burning factory-built appliance has

no gas access hole(s) provided, an access hole of 1½ inch (38.1mm) or less may be drilled through the lower

sides or bottom of the appliance in a proper workman like manner. This access hole must be plugged with non

-

combustible insulation after the gas supply line has been installed.

Ensure that existing chimney cleanouts ﬁ t properly.

The refractory, glass doors, screen rails, screen mesh and log grates may be removed from the existing

appliance before installing the gas appliance insert.

Smoke shelves, shields and bafﬂ es may be removed if attached by mechanical fasteners.

The ventilation openings in the existing appliance may be obstructed by the backer plates, aluminium trim etc.

but these parts are not to be applied so as to have an airtight seal.

!

WARNING

RISK OF FIRE, MAINTAIN SPECIFIED AIR SPACE CLEARANCES TO VENT PIPE AND APPLIANCE.

W385-0199_B

WARNING: THIS FIREPLACE HAS BEEN CONVERTED FOR USE WITH A GAS FIREPLACE

INSERT ONLY AND CANNOT BE USED FOR BURNING WOOD OR SOLID FUELS UNLESS ALL ORIGINAL

PARTS HAVE BEEN REPLACED AND THE FIREPLACE IS RE-APPROVED BY THE AUTHORITY HAVING

JURISDICTION.

ATTENTION: CE FOYER A ETE CONVERTI AFIN D’ETRE UTILISE SEULEMENT

COMME FOYER ENCASTRE AU GAZ ET NE PEUT ETRE UTILSE POUR BRULER DU BOIS OU

TOUT AUTRE COMBUSTIBLE SOLIDE, SANS QUE TOUTES LES PIECES ORIGINALES AIENT

ETE REMPLACEES ET QUE LE FOYER SOIT APPROUVE DE NOUVEAU PAR LES AUTORITES

AYANT JURIDICTION.

ADVERTENCIA: ESTA CHIMENEA SE REMODELÓ PARA USARSE SOLO CON UNA

INSERCIÓN DE CHIMENEA A GAS Y NO PUEDE USARSE PARA QUEMAR MADERA NI COMBUSTIBLES

SÓLIDOS, A MENOS QUE SE HAYAN REEMPLAZADO TODAS LAS PIEZAS ORIGINALES, Y LA AUTORI-

DAD JURISDICCIONAL LA HAYA VUELTO A APROBAR.

W415-1365 / A / 07.28.16

10

EN

While the liners must be continuous from the appliance to the chimney cap, to

achieve the needed length, they may be coupled, using an approved coupler.

We recommend that exhaust vents that pass through unheated spaces,

such as tall exterior chimneys, be wrapped in a protective sleeve to minimize

condensation and reverse ﬂ ow symptoms. See the "TROUBLESHOOTING"

section for details.

This appliance is approved for use with a 2" (51mm) liner for air intake and a 3"

(76mm) liner for exhaust. For best performance, however, it is recommended to

use two 3" (76mm) liners.

If a 2" (51mm) liner is used for the intake, it may be necessary to adjust the

primary air shutter.

A. OUTSIDE: Slip the one end of a liner a

minimum of 2"

(51mm)

over the sleeve

of the air terminal. Secure using 3

screws. Then seal the joint and screw

heads with W573-0007 Mill-Pac (not

supplied). Repeat with the other liner.

NOTE: We recommend that the

other end of the exhaust liner be

marked to eliminate the exhaust

liner being connected to the intake

collar at the appliance.

B. Gently stretch the liners to the required

lengths and insert into the chimney.

Trim and ﬁ t the ﬂ ashing plate to suit

the chimney termination. Place the air

terminal onto the top of the chimney.

Make weather tight by sealing with

caulking (not supplied). Fasten to the

chimney with screws and plugs (not

supplied).

C. INSIDE: Remove the securing screw

from the front of the vent mounting

plate. Pull the vent mounting plate

only, back into the track, to the

front stop. Start the slider back into

position. Re-secure the screw. The

appliance may now be pushed into its

ﬁ nal position inside the wood burning

appliance, and the screw tightened

until the slider has been pulled tight to

the front stop.

D. Route the ﬂ ex liners through the slider. Attach and secure the liners to the vent mounting plate using

the same procedure as before, ensuring that the marked exhaust liner is attached to the exhaust

collar.

FLASHING

PLATE

2” (50.8mm)

OVERLAP

MILL-PAC

INTAKE

EXHAUST

MOUNTING

PLATE

SECURING

SCREW

INTAKE

EXHAUST

2" (50.8mm)

OVERLAP

MILL-PAC

2" (50.8mm)

LINER

3" (76.2mm)

LINER

SLIDER

REDUCER

CONNECTION

ILLUSTRATED WITH A 2"

(50.8mm) INTAKE LINER.

3.2 CHIMNEY CONNECTION

Chimney installation must conform to both national and local code requirements. The chimney must be lined

with one 2" (50.8mm) or 3" (76.2mm) diameter liner for intake and one 3" (76.2mm) diameter liner for exhaust.

The minimum and maximum vent lengths are 10ft (3m) and 35ft (10.7m) respectively. Recommended kits

come in 3 lengths:

1-2"Ø (25.4mm-50.8mm) & 1-3"Ø (25.4mm-76.2mm) DOUBLE PLY ALUMINUM LINER-INLET AND

EXHAUST & 2-3"Ø (50.8mm-76.2mm) TO 2"Ø (50.8mm) REDUCERS:

GDI-2320KT VENT KIT 20FT (6.1m)

GDI-2325KT VENT KIT 25FT (7.6m)

GDI-2335KT VENT KIT 35FT (10.7m)

2-3"Ø (50.8mm-76.2mm) DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST:

GDI-320KT VENT KIT 20FT (6.1m)

GDI-325KT VENT KIT 25 FT (7.6m

GDI-335KT VENT KIT 35 FT (10.7m)

W415-1365 / A / 07.28.16

11

EN

3.3 GAS INSTALLATION

3.4 OPTIONAL WALL SWITCH

30.1A

Installation and servicing to be done by a qualiﬁ ed installer.

• Move the appliance into position and secure.

• If equipped with a ﬂ ex connector the appliance is designed to accept a 1/2” (13mm) gas supply.

Without the connector it is designed to accept a 3/8” (9.5mm) gas supply. The appliance is equipped

with a manual shut off valve to turn off the gas supply to the appliance.

• Connect the gas supply in accordance to local codes. In the absence of local codes, install to the

current CAN/CSA-B149.1 Installation Code in Canada or to the current National Fuel Gas Code, ANSI

Z223.1 / NFPA 54 in the United States.

• When ﬂ exing any gas line, support the gas valve so that the lines are not bent or kinked.

• The gas line ﬂ ex-connector should be installed to provide sufﬁ cient movement for shifting the burner

assembly on its side to aid with servicing components.

• Check for gas leaks by brushing on a soap and water solution. Do not use open ﬂ ame.

!

WARNING

RISK OF FIRE, EXPLOSION OR ASPHYXIATION. ENSURE THERE ARE NO IGNITION SOURCES SUCH AS

SPARKS OR OPEN FLAMES.

SUPPORT GAS CONTROL WHEN ATTACHING GAS SUPPLY PIPE TO PREVENT DAMAGING GAS LINE.

ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT

WITH THE GLASS DOOR OPENED OR REMOVED. PURGING OF THE GAS SUPPLY LINE SHOULD BE

PERFORMED BY A QUALIFIED SERVICE TECHNICIAN. ASSURE THAT A CONTINUOUS GAS FLOW IS AT

THE BURNER BEFORE CLOSING THE DOOR. ENSURE ADEQUATE VENTILATION. FOR GAS AND

ELECTRICAL LOCATIONS, SEE “DIMENSIONS” SECTION.

ALL GAS CONNECTIONS MUST BE CONTAINED WITHIN THE APPLIANCE WHEN COMPLETE.

HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE TESTING GAS

LINE AT TEST PRESSURES ABOVE 1/2 PSIG.

VALVE SETTINGS HAVE BEEN FACTORY SET, DO NOT CHANGE.

For ease of accessibility, an optional remote wall switch may be installed in a convenient location. Route a

2 strand, solid core millivolt wire from the valve to the wall switch. The recommended maximum lead length

depends on wire size:

WIRE SIZE MAX. LENGTH

14 gauge 100 feet (30.5m)

16 gauge 60 feet (18.3m)

18 gauge 40 feet (12m)

Disconnect the existing wires from terminals 1 and 3 (from the

ON/OFF switch) and replace with the leads from the wall switch.

50.5

P

I

L

O

T

TP

!

WARNING

DO NOT CONNECT THE WALL SWITCH OR GAS VALVE DIRECTLY TO 110 VOLT ELECTRICITY.

1

3

P

I

P

I

L

O

T

N

O

L

O

T

H

I

L

O

F

O

A

B

W415-1365 / A / 07.28.16

12

EN

4.0 FINISHING

6” (152mm) MANTEL

3”

4”

5”

12”

(305mm)

13”

(330mm)

14”

(356mm)

15”

(381mm)

TOP OF APPLIANCE

Combustible mantel clearance can vary according to the mantel depth. Use the graph to help evaluate the

clearance needed. These same requirements apply to any combustibles protruding on either side of the

appliance.

0

$

1

7

(

/

+

(

,

*

+

7



3456

MANTEL DEPTH

14" (356mm)

12" (305mm)

13" (330mm)

15" (381mm)

(76mm) (102mm)(127mm) (152mm)

!

WARNING

RISK OF FIRE, MAINTAIN ALL SPECIFIED AIR SPACE CLEARANCES TO COMBUSTIBLES. FAILURE

TO COMPLY WITH THESE INSTRUCTIONS MAY CAUSE A FIRE OR CAUSE THE APPLIANCE TO

OVERHEAT. ENSURE ALL CLEARANCES (I.E. BACK, SIDE, TOP, VENT, MANTEL, FRONT, ETC.) ARE

CLEARLY MAINTAINED.

WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE

HEAT RESISTANT TO PREVENT DISCOLOURATION.

73.1

!

WARNING

RISK OF FIRE!

NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.

IF FINISHING THE FRONT OF THE APPLIANCE, IT MUST BE FINISHED WITH ANY NON-COMBUSTIBLE

MATERIAL SUCH AS BRICK, MARBLE, GRANITE, ETC.

DO NOT STRIKE, SLAM OR SCRATCH GLASS. DO NOT OPERATE APPLIANCE WITH GLASS

REMOVED, CRACKED, BROKEN OR SCRATCHED.

FACING AND/OR FINISHING MATERIAL MUST NEVER OVERHANG INTO THE APPLIANCE OPENING.

72.1B

4.1 MINIMUM MANTEL CLEARANCES

W415-1365 / A / 07.28.16

13

EN

4.2 SAFETY SCREEN REMOVAL AND INSTALLATION

!

WARNING

GLASS MAY BE HOT, DO NOT TOUCH GLASS UNTIL COOLED.

IF EQUIPPED WITH DOOR LATCHES THAT ARE PART OF A SAFETY RELIEF SYSTEM, THEY MUST BE

PROPERLY ENGAGED. DO NOT OPERATE THE APPLIANCE WITH LATCHES DISENGAGED.

FACING AND/OR FINISHING MATERIALS MUST NOT INTERFERE WITH AIR FLOW THROUGH AIR

OPENINGS, LOUVRE OPENINGS, OPERATION OF LOUVRES OR DOORS OR ACCESS FOR

SERVICE. OBSERVE ALL CLEARANCES WHEN APPLYING COMBUSTIBLE MATERIALS.

BEFORE DOOR IS REMOVED TURN THE APPLIANCE OFF AND WAIT UNTIL APPLIANCE IS COOL TO

THE TOUCH. DOORS ARE HEAVY AND FRAGILE SO HANDLE WITH CARE.

75.1A

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the

appliance and must be installed.

Before the glass door can be removed, the faceplate and safety screen must be removed. Lift the faceplate

up and off the appliance door and remove from the appliance.

FLASHING

SAFETY SCREEN

TOP CLIPS

BOTTOM BRACKETS

SAFETY SCREEN FRAME

TOP BRACKETS

DOOR FRAME

TOP BRACKETS

SCREWS

A.

B.

C.

D.

A. Remove the top clips and set aside.

B. Remove the safety screen from the safety

screen frame by sliding it up and out.

C. Remove the two screws from the top

brackets of the safety screen frame.

D. Lift the safety screen frame up and away

from door frame.

REMOVAL:

INSTALLATION:

E. Install the safety screen frame into the

bottom brackets of the door frame and

secure the top brackets with the 2 screws

into the top brackets of the door frame.

F. Slide the safety screen into the safety

screen frame.

G. Install the top clips.

H. Ensure the safety screen is installed

correctly before using the appliance.

W415-1365 / A / 07.28.16

14

EN

To open the door, the safety screen must be

removed to allow the door to be opened or

closed. Release the top and bottom door

latches, located at the right side of the door.

Reverse these steps to close the door. Ensure the

safety screen is installed correctly before using

appliance.

NOTE: The protective wrap on plated parts is

best removed when the assembly is at room

temperature but this can be improved if the

assembly is warmed, using a hair dryer or

similar heat source.

DOOR LATCH

4.3 DOOR REMOVAL AND INSTALLATION

A. Remove the 3 screws from the location shown

in the base of the ﬁ rebox.

B. Secure the grate to the ﬁ rebox base using the

3 screws removed.

4.4 GRATE INSTALLATION

W415-1365 / A / 07.28.16

15

EN

4.5 LOG PLACEMENT

!

WARNING

FAILURE TO POSITION THE LOGS IN ACCORDANCE WITH THESE DIAGRAMS OR FAILURE TO USE

ONLY LOGS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY

DAMAGE OR PERSONAL INJURY.

LOGS MUST BE PLACED IN THEIR EXACT LOCATION IN THE APPLIANCE. DO NOT MODIFY THE

PROPER LOG POSITIONS, SINCE APPLIANCE MAY NOT FUNCTION PROPERLY AND DELAYED

IGNITION MAY OCCUR.

THE LOGS ARE FRAGILE AND SHOULD BE HANDLED WITH CARE.

76.1A

PHAZER

TM

logs and glowing embers exclusive to Napoleon, provide a unique and realistic glowing effect that is

different in every installation. Take the time to carefully position the glowing embers for a maximum glowing effect.

Log colours may vary. During the initial use of the appliance, the colours will become more uniform as colour

pigments burn in during the heat activated curing process.

A. Place the rear log so that it rests against

the two log brackets on the back wall of the

ﬁ rebox. The air space between the log and

ﬁ rebox back is used to facilitate combustion

air ﬂ ow.

B. Move the charcoal strip into position lining

up the holes in the bottom with the studs

located on the burner. Ensure strip sits ﬂ at on

the burner.

B

A

E. Line up the square hole in the right crossover

with the square post located on the right

side of log and install as shown.

F. Line up the rectangular hole in the left

crossover with the rectangular post located

on the left side of log and install as shown.

B

A

C

D

E

B

A

C

D

E

F

C. Position the front right log just behind the

grate. Line up the log with the studs located

on the log support.

D. Move the left log into position lining up the

hole in the bottom with the stud on the left

side of the log support.

B

A

C

B

A

C

D

W415-1365 / A / 07.28.16

16

EN

Tear the embers into pieces and place along the front row of ports covering all of the burner area in front of

the small logs. Care should be taken to shred the embers into thin, small irregular pieces as only the exposed

edges of the ﬁ bre hairs will glow. The ember material will only glow when exposed to direct ﬂ ame;

however, care should be taken to not block the burner ports.

Blocked burner ports can cause an incorrect ﬂ ame pattern, carbon deposits and delayed ignition. PHAZER

TM

logs glow when exposed to direct ﬂ ame. Use only certiﬁ ed "glowing embers" and PHAZER

TM

logs available

from your authorized dealer / distributor.

32.1

Randomly place the charcoal embers along the

f

ront and sides o

f

the log support tray in a realistic manner.

Fine dust found in the bottom of the bag should not be used.

NOTE: Charcoal embers are not to be placed on the burner.

97.1A

Remove the backing of the logo supplied and place on the glass viewing

door, as indicated.

½"(12.7mm)

LOGO

½"(12.7mm)

4.6 OPTIONAL CHARCOAL EMBERS

4.7 GLOWING EMBERS

4.8 LOGO PLACEMENT

W415-1365 / A / 07.28.16

17

EN

5.0 BLOWER REPLACEMENT

black

white

red

SPEED

CONTROL

SWITCH

BLOWER

THERMAL

SWITCH

FRONT BLOWER ACCESS COVER

REAR BLOWER ACCESS COVER

A. Turn off the electrical power and the gas

supply to the appliance.

B. Open the glass door and remove the logs and

ﬁ bre bricks, if installed.

C. Remove the front blower access cover held on

with 4 screws.

D. Remove the rear blower access cover. NOTE:

Check the blower gasket for damage.

Replace if damaged.

E. Disconnect the two blower wires. Remove the

blower from the mounting plate and replace.

For thermal switch replacement: Remove the

mounting bracket secured to the underside of

the burner base. Remove the thermal switch

from the bracket and replace.

F. Reconnect the two wires. Re-install the blower

gasket. Reattach the blower mounting plate

and blower access covers. Replace the logs.

Close the ﬁ re viewing door.

G. Turn the gas supply and electricity back on.

Because the blower is thermally activated,

when turned on, it will automatically start

approximately 5-15 minutes after lighting the

appliance and will run for approximately 30-45

minutes after the appliance has been turned

off. Use of the fan increases the output of heat.

Drywall dust will penetrate into the blower

bearings causing irreparable damage and must

be prevented from coming into contact with

the blower or its compartment. Any damage

resulting from this condition is not covered by

the warranty policy.

!

WARNING

RISK OF FIRE AND ELECTRICAL SHOCK.

TURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THIS APPLIANCE.

USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH

THIS APPLIANCE. USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS

COMPONENTS, VENTING COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL

VOID THE WARRANTY AND CERTIFICATION.

ENSURE THAT THE FAN’S POWER CORD IS NOT IN CONTACT WITH ANY SURFACE OF THE

APPLIANCE TO PREVENT ELECTRICAL SHOCK OR FIRE DAMAGE. DO NOT RUN THE POWER

CORD BENEATH THE APPLIANCE.

THE WIRE HARNESS PROVIDED IN THE BLOWER KIT IS A UNIVERSAL HARNESS. WHEN

INSTALLED, ENSURE THAT ANY EXCESS WIRE IS CONTAINED, PREVENTING IT FROM MAKING

CONTACT WITH MOVING OR HOT OBJECTS.

51.5

THERMAL SWITCH / BRACKET

ASSEMBLY

W415-1365 / A / 07.28.16

18

EN

6.0 OPERATION

Ensure that a continuous gas flow is at the burner before installing the door. When lit for the first time, the appliance will

emit an odor for a few hours. This is a normal temporary condition caused by the "burn-in" of paints and lubricants used in

the manufacturing process and will not occur again.

A

fter extended periods of non-operation such as following a vacation or a warm weather season, the appliance may emit a

slight odor for a few hours. This is caused by dust particles in the heat exchanger burning off. In both cases, open a

window to sufficiently ventilate the room.

FOR YOUR SAFETY READ BEFORE LIGHTING:



This appliance is equipped with a pilot which must be lit by hand while following these instructions exactly.



Before operating smell all around the appliance area for gas and next to the floor because some gas is heavier than

air and will settle on the floor.



Use only your hand to turn the gas control knob. Never use tools. If the knob will not turn by hand, do not try to

repair it. Call a qualified service technician. Force or attempted repair may result in a fire or explosion.



Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect

the appliance and replace any part of the control system and any gas control which has been under water.

Turn off all gas to the appliance.

Open windows.

Do not try to light any appliance.

Do not touch any electric switch; do not use any

phone in your building.

*$6.12%

:$51,1*7KHJDVYDOYHKDVDQLQWHUORFNGHYLFHZKLFKZLOOQRWDOORZWKHSLORWEXUQHUWREHOLWXQWLOWKHWKHUPR-

FRXSOHKDVFRROHG$OORZDSSUR[LPDWHO\VHFRQGVIRUWKHWKHUPRFRXSOHWRFRRO

When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob is depressed slightly.

$ Stop! Read the above safety information on this label.

% Turn off all electric power to the appliance.

& Turn the gas knob clockwise to off.

' Wait five (5) minutes to clear out any gas. If you smell gas including near the floor. Stop! Follow "B" in the

above safety information on this label. If you don't smell gas go the next step.

( Turn gas knob counter-clockwise to pilot.

) Depress slightly and hold gas knob while lighting the pilot with the push button igniter. Keep knob depressed for one

minute, then release. If pilot does not continue to burn, repeat steps 3 through 5.

* With pilot lit, depress and turn gas knob counter-clockwise to on.

+ If equipped with remote on-off switch / thermostat, main burner may not come on when you turn valve to on. Remote

switch must be in the on position to ignite burner.

, Turn on all electric power to the appliance.

$ Turn off all electric power to the appliance if service is to be performed.

% Push in gas control knob slightly and turn clockwise to off. Do not force.

Immediately call your gas supplier from a

neighbor's phone. Follow the gas

supplier's instructions.

If you cannot reach your gas supplier,

call the fire department.

WHAT TO DO IF YOU SMELL GAS:

LIGHTING INSTRUCTIONS:

TO TURN OFF GAS

TURN THE CONTROL VALVE TO THE OFF POSITION WHEN HEATER IS NOT IN USE.



,)<28'2127)2//2:7+(6(,16758&7,216(;$&7/<$),5(25(;3/26,210$<5(68/7

&$86,1*3523(57<'$0$*(3(5621$/,1-85<25/2662)/,)(

$/:$<6/,*+77+(3,/27:+(7+(5)257+(),5677,0(25,)7+(*$66833/<+$6581287:,7+

7+(*/$66'22523(1('255(029('

!

WARNING

W415-1365 / A / 07.28.16

19

EN

7.0 ADJUSTMENTS

7.1 PILOT BURNER ADJUSTMENT

Adjust the pilot screw to provide properly sized ﬂ ame. Turn in a clockwise

direction to reduce the gas ﬂ ow.

Inlet pressure can be checked by turning screw (A)

counter-clockwise until loosened and then placing

pressure gauge tubing over the test point. Gauge should

read 7” (178mm) (minimum 4.5”(114mm)) water column for

natural gas or 13” (330mm) (11” minimum (279mm)) water column

for propane. Check that main burner is operating on “HI”.

Outlet pressure can be checked the same as above using screw (B).

Gauge should read 3.5” (89mm) water column for natural gas or 10”

(254mm) water column for propane. Check that main burner is operating

on “HI”.

AFTER TAKING PRESSURE READINGS, TIGHTEN SCREWS

FIRMLY TO SEAL. DO NOT OVER TORQUE. LEAK TEST.

39.3B

P

I

P

I

L

O

T

N

O

L

O

T

H

I

L

O

F

O

PILOT

BURNER

THERMOCOUPLE

THERMOPILE

7.2 VENTURI ADJUSTMENT

This appliance has an air shutter that has been factory set open according

to the chart below:

Regardless of venturi orientation, closing the air shutter will cause a more

yellow ﬂame, but can lead to carbonization. Opening the air shutter will

cause a more blue ﬂame, but can cause ﬂame lifting from the burner ports.

The ﬂame may not appear yellow immediately; allow 15 to 30 minutes for

the ﬁnal ﬂame colour to be established.

AIR SHUTTER ADJUSTMENT MUST ONLY BE DONE BY A QUALIFIED

INSTALLER!

AIR

SHUTTER

OPENING

VENTURI

BURNER

ORIFICE

49.1

GDI-30

NG 1/4” (6.4mm)

LP 3/8” (9.5mm)

It’s important to periodically perform a visual check of the pilot and

burner ﬂ ames. Compare them to the illustrations provided. If any ﬂ ame

appears abnormal call a service person.

54.2A

3/8” - 1/2”

FLAME MUST

ENVELOP UPPER

3/8" TO 1/2"

(12.7mm - 9.5mm) OF

THERMOCOUPLE &

THERMOPILE

(9.5mm - 12.7mm)

7.3 FLAME CHARACTERISTICS

Pressure

Inlet

Outlet

Natural Gas

(inches)

Natural Gas

(millibars)

Propane

(inches)

Propane

(millibars)

7"

(MIN. 4.5")

3.5"

13"

(MIN. 11")

10"

17.4mb

(MIN. 11.2mb)

8.7mb

32.4mb

(MIN. 27.4mb)

24.9mb

W415-1365 / A / 07.28.16

20

EN

8.0 MAINTENANCE

This appliance and its venting system should be inspected before use and at least annually by a qualiﬁ ed

service person. The following suggested checks should be performed by a qualiﬁ ed technician. The

appliance area must be kept clear and free of combustible materials, gasoline or other ﬂ ammable vapors and

liquids. The ﬂ ow of combustion and ventilation air must not be obstructed.

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper

and dangerous operation. Verify proper operation after servicing.

A. In order to properly clean the burner and pilot assembly, remove the logs, rocks and/or glass to

expose both assemblies.

B. Keep the control compartment, media, burner, air shutter opening and the area surrounding the logs

clean by vacuuming or brushing, at least once a year.

C. Check to see that all burner ports are burning. Clean out any of the ports which may not be burning

or are not burning properly.

D. Check to see that the pilot ﬂ ame is large enough to engulf the ﬂ ame sensor and/or thermocouple /

thermopile as well as reaches the burner.

E. Replace the cleaned logs, rocks or glass. Failure to properly position the media may cause carbon

which can be distributed inside of ﬁ rebox and on exterior surfaces surrounding vent termination.

F. Check to see that the main burner ignites completely on all openings when turned on. A 5 to 10

second total light-up period is satisfactory. Service as required.

G. Check that the gasketing on the sides, top and bottom of the door is not broken or missing. Replace

if necessary.

H. If for any reason the vent air intake system is disassembled, re-install and re-seal per the instructions

provided for the initial installation.

I. Cleaning the safety barrier may be necessary due to excessive lint / dust from carpeting, pets, etc.

simply vacuum using the brush attachment.

J. Ensure the relief system performs effectively. Check that the gasket is not worn or damaged. Replace

if necessary.

40.1E

TURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THE APPLIANCE.

APPLIANCE MAY BE HOT, DO NOT SERVICE UNTIL APPLIANCE HAS COOLED.

DO NOT USE ABRASIVE CLEANERS.

DO NOT PAINT THE PILOT ASSEMBLY.

MAINTENANCE

!

WARNING

La page charge ...

NAPOLEON GDI-30NSB Le manuel du propriétaire

NAPOLEON GDI-30NSB Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents