NAPOLEON GDS20 Le manuel du propriétaire

Catégorie
Cheminées
Taper
Le manuel du propriétaire
EN
W415-1326 / A / 09.13.17
FR
PG
45
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE
INSTALLATION AND
OPERATING INSTRUCTIONS
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone 1 (866) 820-8686 • www.napoleonfi replaces.com • [email protected]
1.1A
$10.00
SAFETY INFORMATION
!
WARNING
- Do not store or use gasoline or other fl ammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use
any phone in your building.
Immediately call your gas supplier from a
neighbour’s phone. Follow the gas supplier’s
instructions.
If you cannot reach your gas supplier, call the
re department.
- Installation and service must be performed by a
qualifi ed installer, service agency or the supplier.
This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by
local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless a
certifi ed kit is used.
If the information in these instructions
are not followed exactly, a fi re or
explosion may result causing property
damage, personal injury or loss of life.
LA VITRE CHAUDE CAUSERA
DES BRÛLURES.
NE PAS TOUCHER LA VITRE
AVANT QU’ELLE AIT REFROIDI.
NE JAMAIS LAISSER LES
ENFANTS TOUCHER LA VITRE.
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
!
DANGER
!
AVERTISSEMENT
A barrier designed to reduce the risk of burns from
the hot viewing glass is provided with this appliance
and shall be installed for the protection of children
and other at-risk individuals.
Une barriére conçu à réduire le risque de brûlures
causées par le verre chaud est fourni avec l’appareil
et sera installé pour la protection des enfants et
d’autres personnes à risque.
LA VITRE CHAUDE CAUSERA
DES BRÛLURES.
NE PAS TOUCHER LA VITRE
AVANT QU’ELLE AIT REFROIDI.
NE JAMAIS LAISSER LES
ENFANTS TOUCHER LA VITRE.
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
!
WARNING
!
AVERTISSEMENT
ADD ETL,
OMNI or CSA
LOGO HERE
ADD SAFETY STANDARD INFORMATION...
ADD
PRODUCT
IMAGE
FOR INDOOR USE ONLY!
SAFETY
SCREEN
GDS20N
NATURAL GAS
GDS20P
PROPANE
CONFORMS TO AMERICAN NATIONAL STANDARDS: ANSI Z21.50, CERTIFIED TO CANADIAN CSA 2.22 FOR VENTED DECORATIVE GAS APPLIANCE.
W415-1326 / A / 09.13.17
2
EN
TABLE OF CONTENTS
NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.
1.0 INSTALLATION OVERVIEW 3
2.0 INTRODUCTION 4
2.1 DIMENSIONS 5
2.2 GENERAL INSTRUCTIONS 5
2.3 GENERAL INFORMATION 6
2.4 RATING PLATE INFORMATION 7
3.0 VENTING 8
3.1 VENTING LENGTHS AND COMPONENTS 9
3.2 TYPICAL VENT INSTALLATION 10
3.3 SPECIAL VENT INSTALLATIONS 11
3.3.1 PERISCOPE TERMINATION 11
3.3.2 CORNER TERMINATION 11
3.4 VENT TERMINAL CLEARANCES 12
3.5 DEFINITIONS 13
3.6 ELBOW VENT LENGTH VALUES 13
3.7 TOP EXIT HORIZONTAL TERMINATION 14
3.8 VERTICAL TERMINATION 16
4.0 INSTALLATION 18
4.1 WALL AND CEILING PROTECTION 18
4.1.1 HORIZONTAL INSTALLATION 19
4.1.2 VERTICAL INSTALLATION 19
4.2 APPLIANCE VENT CONNECTION 20
4.3 HORIZONTAL AIR TERMINAL INSTALLATION 20
4.4 VERTICAL THROUGH EXISTING CHIMNEY 21
4.5 VERTICAL AIR TERMINAL INSTALLATION 22
4.6 GAS INSTALLATION 23
4.7 OPTIONAL WALL SWITCH 23
4.8 MOBILE HOME INSTALLATION 24
4.9 MINIMUM CLEARANCE TO COMBUSTIBLES 24
5.0 FINISHING 25
5.1 CAST FRONT INSTALLATION AND REMOVAL 25
5.2 GLASS DOOR INSTALLATION AND REMOVAL 25
5.3 SAFETY SCREEN INSTALLATION AND REMOVAL 26
5.4 LOG PLACEMENT 27
5.5 LOGO PLACEMENT 27
6.0 OPTIONAL BLOWER INSTALLATION 28
7.0 OPERATION 29
8.0 ADJUSTMENTS 30
8.1 PILOT BURNER ADJUSTMENT 30
8.2 VENTURI ADJUSTMENT 30
8.3 FLAME CHARACTERISTICS 31
8.4 RESTRICTING VERTICAL VENTS 31
9.0 MAINTENANCE 31
9.1 ANNUAL MAINTENANCE 32
9.2 PILOT INDICATOR LIGHT BATTERY REPLACEMENT 33
9.3 ORIFICE REPLACEMENT 33
9.4 CARE OF GLASS 33
10.0 REPLACEMENTS 34
11.0 OVERVIEW 35
12.0 ACCESSORIES 36
13.0 VALVE TRAIN ASSEMBLY 37
14.0 TROUBLESHOOTING 38
15.0 WARRANTY 41
16.0 SERVICE HISTORY 42
17.0 NOTES 43
W415-1326 / A / 09.13.17
3
EN
1.0 INSTALLATION OVERVIEW
Venting, see “VENTING” section.
Door, see “FINISHING -
GLASS DOOR
INSTALLATION AND
REMOVAL” section.
Blower, see “OPTIONAL
BLOWER
INSTALLATION” section.
Cast top, see “FINISHING - CAST
FRONT INSTALLATION AND
REMOVAL” section.
Rating Plate, see
“RATING PLATE
INFORMATION” section.
SAFETY
SCREEN
W415-1326 / A / 09.13.17
4
EN
2.0 INTRODUCTION
W415-1326 / 05.23.14
4
EN
2.0 INTRODUCTION
3.1D
!
WARNING
THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.
ANY CHANGES TO THIS APPLIANCE OR IT’S CONTROLS CAN BE DANGEROUS AND IS PROHIBITED.
Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to
operating instructions could cause re or injury.
Risk of re or asphyxiation do not operate appliance with xed glass removed.
Do not connect 110 volts to the control valve.
Risk of burns. The appliance should be turned off and cooled before servicing.
Do not install damaged, incomplete or substitute components.
Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges may be sharp.
Do not burn wood or other materials in this appliance.
Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or
clothing ignition.
Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers,
young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at
risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers,
young children and other at risk individuals out of the room and away from hot surfaces.
Clothing or other ammable material should not be placed on or near the appliance.
Due to high temperatures, the appliance should be located out of traf c and away from furniture and draperies.
Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.
Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.
Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot surfaces. These
screens and guards must be fastened to the oor.
Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior to operating the appliance.
The appliance is a vented gas- red appliance. Do not burn wood or other materials in the appliance.
The appliance area must be kept clear and free from combustible materials, gasoline and other ammable vapors and liquids.
Under no circumstances should this appliance be modi ed.
This appliance must not be connected to a chimney ue pipe serving a separate solid fuel burning appliance.
Do not use this appliance if any part has been under water. Immediately call a quali ed service technician to inspect the
appliance and to replace any part of the control system and any gas control which has been under water.
Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be done by a
licensed or quali ed service person.
Do not strike or slam shut the appliance glass door.
When equipped with pressure relief doors, they must be kept closed while the appliance is operating to prevent exhaust fumes
containing carbon monoxide, from entering into the home. Temperatures of the exhaust escaping through these openings can
also cause the surrounding combustible materials to overheat and catch re.Only doors / optional fronts certi ed with the unit
are to be installed on the appliance.
Only doors / optional fronts certi ed with the unit are to be installed on the appliance.
Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic bags,
these are not toys and should be kept away from children and infants.
As with any combustion appliance, we recommend having your appliance regularly inspected and serviced as well as having a
Carbon Monoxide Detector installed in the same area to defend you and your family against Carbon Monoxide.
Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance. Elevated
temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage to decorations, a T.V.
or other electronic components.
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed.
If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this appliance.
Installation and repair should be done by a quali ed service person. The appliance should be inspected before use and at
least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting,
bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be
kept clean.
This appliance uses and requires a fast acting thermocouple. Replace only with a fast acting thermocouple supplied by Wolf
Steel Ltd.
W415-1326 / A / 09.13.17
5
EN
2.1 DIMENSIONS
25 3/8"
645mm
SAFETY
SCREEN
18 1/2"
470mm
24"
610mm
19 1/4”
Ø 4"
[102mm]
Ø 7"
[178mm]
489mm
9 5/8"
245mm
2.2 GENERAL INSTRUCTIONS
W415-1326 / 05.23.14
5
EN
2.1 DIMENSIONS
25 3/8"
645mm
SAFETY
SCREEN
18 1/2"
470mm
24"
610mm
19 1/4”
Ø 4"
[102mm]
Ø 7"
[178mm]
489mm
9 5/8"
245mm
2.2 GENERAL INSTRUCTIONS
THIS GAS APPLIANCE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to
conform with local codes. Installation practices vary from region to region and it is important to know the
speci cs that apply to your area, for example in Massachusetts State:
This product must be installed by a licensed plumber or gas tter when installed within the commonwealth
of Massachusetts.
The appliance damper must be removed or welded in the open position prior to installation of an appliance
insert or gas log.
The appliance off valve must be a “T” handle gas cock.
• The exible connector must not be longer than 36 inches (914mm).
A Carbon Monoxide detector is required in all rooms containing gas red appliances.
The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent
sealed combustion product.
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT,
WITH THE GLASS DOOR OPENED OR REMOVED.
PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.
PROVIDE ADEQUATE VENTILATION.
NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.
OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48” (1219mm) FROM
THE FRONT FACE OF THE APPLIANCE.
SURFACES AROUND AND ESPECIALLY ABOVE THE APPLIANCE CAN BECOME HOT. AVOID CONTACT
WHEN THE APPLIANCE IS OPERATING.
FIRE RISK. EXPLOSION HAZARD.
HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE PRESSURE TESTING GAS
LINE AT TEST PRESSURES ABOVE 1/2 PSIG. CLOSE THE MANUAL SHUT-OFF VALVE BEFORE PRESSURE
TESTING GAS LINE AT TEST PRESSURES EQUAL TO OR LESS THAN 1/2 PSIG (35 mb).
USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH THIS APPLIANCE.
USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS COMPONENTS, VENTING
COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICATION.
!
WARNING
W415-1326 / A / 09.13.17
6
EN
The blower power cord must be connected into a properly grounded receptacle. The grounding prong must not
be removed from the cord plug.
2.3 GENERAL INFORMATION
FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND
QUALITY!
GDS20
NG P
Altitude (FT) 0-4,500 0-4500
Max. Input (BTU/HR) 20,000 20,000
Max. Output (BTU/HR) 15,600 15,600
Efciency (w/ the fan on) 78% 78%
Min. Inlet Gas Supply Pressure 4.5" Water Column (11.2mb) 11" Water Column (27.4mb)
Max. Inlet Gas Supply Pressure 7" Water Column (17.4mb) 13" Water Column (32mb)
Manifold Pressure (Under Flow Conditions) 3.5" Water Column (8.7mb) 10" Water Column (25mb)
When the appliance is installed at elevations above 4,500ft (1372m), and in the absence of specic recommendations
from the local authority having jurisdiction, the certied high altitude input rating shall be reduced at the rate of 4%
for each additional 1,000ft (305mm). Expansion / contraction noises during heating up and cooling down cycles are
normal and to be expected.
Provided that the clearance to combustibles are achieved, the most desirable and benecial location for an
appliance is in the centre of a building, thereby allowing the most efcient use of the heat created. The location
of windows, doors and the trafc ow in the room where the appliance is to be located should be considered.
If possible, you should choose a location where the vent will pass through the house without cutting a oor or
roof joist.
This appliance is approved for closet or recessed installations, as well as for bathroom, bedroom and bed-
sitting room installations and is suitable for mobile home installations. The natural gas model can be installed in
a mobile home that is permanently positioned on its site and fueled with natural gas.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use
with other gases, unless a certied kit is used.
W415-1326 / 05.23.14
6
EN
The blower power cord must be connected into a properly grounded receptacle. The grounding prong must not
be removed from the cord plug.
2.3 GENERAL INFORMATION
4.1B
The installation must conform with local codes or, in
absence of local codes, the National Gas and Propane
Installation Code CSA B149.1 in Canada, or the National
Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United
States. Suitable for mobile home installation if installed in
accordance with the current standard CAN/CSA Z240MH
Series, for gas equipped mobile homes, in Canada or
A
NSI Z223.1 and NFPA 54 in the United States.
A
s long as the required clearance to combustibles is
maintained, the most desirable and bene cial location
for an appliance is in the center of a building, thereby
allowing the most ef cient use of the heat created. The location of windows, doors and the traf c ow in the
room where the appliance is to be located should be considered. If possible, you should choose a location
where the vent will pass through the house without cutting a oor or roof joist.
If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood
ooring, the appliance shall be installed on a metal or wood panel extending the full width and depth.
Some appliances have optional fans or blowers. If an optional fan or blower is installed, the junction box must
be electrically connected and grounded in accordance with local codes, use the current CSA C22.1 Canadian
Electrical Code in Canada or the ANSI/NFPA 70 National Electrical code in the United States.
We suggest that our gas
hearth products be installed
and serviced by professionals
who are certied in the U.S.
by the National Fireplace
Institute
®
(NFI) as NFI Gas
Specialists
www.ncertied.org
FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND
QUALITY!
GDS20
NG LP
Altitude (FT) 0-4,500 0-4500
Max. Input (BTU/HR) 20,000 20,000
Max. Output (BTU/HR) 15,600 15,600
Ef ciency (w/ the fan on) 78% 78%
Min. Inlet Gas Supply Pressure 4.5" Water Column (11.2mb) 11" Water Column (27.4mb)
Max. Inlet Gas Supply Pressure 7" Water Column (17.4mb) 13" Water Column (32mb)
Manifold Pressure (Under Flow Conditions) 3.5" Water Column (8.7mb) 10" Water Column (25mb)
When the appliance is installed at elevations above 4,500ft (1372m), and in the absence of speci c recommendations
from the local authority having jurisdiction, the certi ed high altitude input rating shall be reduced at the rate of 4%
for each additional 1,000ft (305mm). Expansion / contraction noises during heating up and cooling down cycles are
normal and to be expected.
Provided that the clearance to combustibles are achieved, the most desirable and bene cial location for an
appliance is in the centre of a building, thereby allowing the most ef cient use of the heat created. The location
of windows, doors and the traf c ow in the room where the appliance is to be located should be considered.
If possible, you should choose a location where the vent will pass through the house without cutting a oor or
roof joist.
This appliance is approved for closet or recessed installations, as well as for bathroom, bedroom and bed-
sitting room installations and is suitable for mobile home installations. The natural gas model can be installed in
a mobile home that is permanently positioned on its site and fueled with natural gas.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use
with other gases, unless a certi ed kit is used.
W415-1326 / A / 09.13.17
7
EN
2.4 RATING PLATE INFORMATION
W415-1326 / 05.23.14
7
EN
2.4 RATING PLATE INFORMATION
W385-1959
SERIAL NUMBER / NO. DESERIE
NOT FOR USE WITH SOLID FUEL
GDS/CDVS20
WOLF STEEL LTD.
24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA
CERTIFIED UNDER / HOMOLOGUE SELON LES NORMES: ANSI 21.50-2012, CSA 2.22-2012 VENTED GAS FIREPLACE / FOYER À GAS VENTILÉ .
THIS FIREPLACE USES AND REQUIRES A FAST ACTING THERMOCOUPLE. REPLACE ONLY WITH A FAST ACTING
THERMOCOUPLE SUPPLIED BY WOLF STEEL LTD.
APPROVED FOR BEDROOM, BATHROOM & BEDSITTING ROOM INSTALLATION. SUITABLE FOR MOBILE HOME
INSTALLATION IF INSTALLED IN ACCORDANCE WITH THE CURRENT STANDARD CAN/CSA Z240MH SERIES GAS
EQUIPPED MOBILE HOMES, IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME
CONSTRUCTION AND SAFETY STANDARD, TITLE 24 CFR, PART 3280. WHEN THIS US STANDARD IS
NOTAPPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME
INSTALLATIONS, SITES AND COMMUNITIES, ANSI / NFPA 501A.
FOR USE WITH BARRIER W565-0155. FOLLOW THE
INSTALLATION INSTRUCTIONS LOCATED IN THE INSTALLATION MANUAL.
CE FOYER UTILISE ET REQUIERT UN THERMOCOUPLE À ACTION RAPIDE. REMPLACEZ UNIQUEMENT AVEC UN
THERMOCOUPLE À ACTION RAPIDE DE WOLF STEEL LTÉE.HOMOLOGUE POUR INSTALLATION DANS UNE
CHAMBRE A COUCHER, UNE SALLE DE BAIN ET UN STUDIO. APPROPRIE POUR INSTALLATION DANS UNE
MAISON MOBILE SI SON INSTALLATION CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SERIE
DE MAISONS MOBILES EQUIPEES AU GAZ, EN VIGUEUR AU CANADA OU AUX ETATS-UNIS DE LA NORME DE
SECURITE ET DE CONSTRUCTION DE MAISONS MANUFACTUREES, TITRE 24 CFR, SECTION 3280. DANS LE
CAS OU CETTE NORME D'ETATS-UNIS NE PEUT ETRE APPLIQUEE, SE REFERER A LA NORME RELATIVE AU
CRITERE DE MESURES DE SECURITE CONTRE L'INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS
MANUFACTURES, LES SITES ET LES COMMUNAUTES, ANSI/NFPA 501A.
POUR UNE UTILISER AVEC BARRIÈRE
W565-0155. SUIVEZ LES INSTRUCTIONS D'INSTALLATION SE TROUVENT DANS LE MANUEL D'INSTALLATION.
9700539 (WSL) 4001657 (NGZ) 4001658 (NAC) 4001659 (WUSA)
GDS20N / CDVS20N MODEL GDS20P / CDVS20P
0-4500FT (0-1370m) ALTITUDE / ELEVATION 0-4500FT (0-1370m)
20,000 BTU/h INPUT / ALIMENTATION 20,000 BTU/h
13,000 BTU/h REDUCED INPUT / ALIMENTATION REDUITE 12,000 BTU/h
60% P4 60%
MANIFOLD PRESSURE: 3.5 INCHES W.C. (NG)
PRESSION AU COLLECTEUR: 3.5" D'UNE
COLONNE D'EAU(GN)
MIN SUPPLY PRESSURE: 4.5" W.C.(NG)
PRESSION D'ALIMENTATION MIN: 4.5" D'UNE
COLONNE D'EAU (GN)
MAX. SUPPLY PRESSURE: 7" W.C. (NG)
PRESSION D'ALIMENTATION MAX: 7" D'UNE
COLONNE D'EAU (GN)
MANIFOLD PRESSURE: 10 INCHES W.C. (LP)
PRESSION AU COLLECTEUR: 10" D'UNE
COLONNE D'EAU(P)
MIN SUPPLY PRESSURE: 11" W.C.(LP)
PRESSION D'ALIMENTATION MIN: 11" D'UNE
COLONNE D'EAU (P)
MAX. SUPPLY PRESSURE: 13" W.C. (LP)
PRESSION D'ALIMENTATION MAX: 13" D'UNE
COLONNE D'EAU (P)
FOR USE WITH GLASS DOORS CERTIFIED WITH
THIS UNIT ONLY.
WARNING: DO NOT ADD ANY MATERIAL TO THE
APPLIANCE, WHICH WILL COME IN CONTACT
WITH THE FLAMES, OTHER THAN THAT SUPPLIED
BY THE MANUFACTURER WITH THE APPLIANCE.
DECORATIVE PRODUCT: NOT FOR USE AS A
HEATING APPLIANCE
ELECTRICAL RATING: 115V 1.5AMP 60HZ
THE APPLIANCE MUST BE VENTED USING THE
APPROPRIATE WOLF STEEL VENT KITS. SEE
OWNERS INSTALLATION MANUAL FOR VENTING
SPECIFICS.
MINIMUM AND MAXIMUM VERTICAL VENT
LENGTHS ARE 3 FEETAND 40 FEET
RESPECTIVELY.
MINIMUM AND MAXIMUM HORIZONTAL VENT
LENGTHS ARE 12 INCHES AND 20 FEET
RESPECTIVELY.
PROPER REINSTALLATION AND RESEALING IS
NECESSARY AFTER SERVICING THE VENT-AIR
INTAKE SYSTEM.
MINIMUM CLEARANCE TO COMBUSTIBLE MATERIAL:
A 4”
B 2”
C 2”
VENT TOP 2” TO CEILING FROM
VENT BOTTOM 1” STOVE TOP 48”
VENT SIDES 1”
UN COMBUSTIBLE SOLIDE NE DOIT PAS ETRE UTILISE AVEC CET APPAREIL.
UTILISER AVEC LES PORTES VITREES
HOMOLOGUEES SEULEMENT AVEC CETTE UNITE.
AVERTISSEMENT: N'AJOUTEZ PAS A CET APPAREIL
AUCUN MATERIAU DEVANT ENTRER EN CONTACT
AVEC LES FLAMMES AUTRE QUE CELUI QUI EST
FOURNI AVEC CETAPPAREIL PAR LE FABRICANT.
PRODUIT DÉCORATIF: NE PAS UTILISER COMME
APPARIEL DE CHAUFFAGE.
CLASS.: 115V 1.5AMP 60HZ
L'APPAREIL DOIT EVACUER SES GAZ EN UTILISANT
L'ENSEMBLE D'EVACUATION PROPRE A WOLF
STEEL.
REFERER AU MANUEL D'INSTALLATION DE
PROPRIETAIRE POUR L'EVACUATION PRECISE. LES
LONGUEURS VERTICALES MINIMALES ET
MAXIMALES SONT3 PIEDS ET 40 PIEDS
RESPECTIVEMENT.
LES LONGUEURS HORIZONTALES MINIMALES
ET MAXIMALES SONT 12 POUCES ET 20 PIEDS
RESPECTIVEMENT.
IL EST IMPORTANT DE BIEN REINSTALLER ET
RESCELLER L'EVENT APRES AVOIR ASSURE LE
MAINTIEN DU SYSTEME DE PRISE D'AIR.
DEGAGEMENTS MINIMAUX DES MATERIAUX
COMBUSTIBLES:
A 4”
B 2”
C 2”
EVENT SUPERIEUR 2”
ENTRE LE DESSUS DU FOYER
EVENT INFERIEUR 1” ET LE PLAFOND 48”
COTES DE L'EVENT 1”
INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to
the model, venting and gas type of the appliance.
For rating plate location, see “INSTALLATION OVERVIEW” section.
This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.
NOTE: The rating plate must remain with the appliance at all times. It must not be removed.
SAMPLE
EL
EL
SAMPLE
M
AM
A
A
A
A
AM
AM
AM
M
E, ON, L4M 0G8 CA
, L4M 0G8 CA
REPLACE / FOYER À GAS VENTIL
REPLACE / FOYER À GAS VENTIL
ERT UN THERMOCOUPLE À ACTION RAPIDE
UN THERMOCOUPLE À ACTION RAPIDE
ACTION RAPIDE DE WOLF STEEL LTÉE.HOMOLO
PIDE DE WOLF STEEL LTÉE.HOMOL
CHER, UNE SALLE DE BAIN ET UN STUDIO. AP
E DE BAIN ET UN STUDIO. AP
E SI SON INSTALLATION CONFORME AUX EXIGE
N CONFORME AUX EXIGE
S MOBILES EQUIPEES AU GAZ, EN VIGUEUR AU
S MOBILES EQUIPEES AU GAZ, EN VIGUEUR AU
E ET DE CONSTRUCTION DE MAISONS MANUFA
E ET DE CONSTRUCTION DE MAISONS MANUF
OU CETTE NORME D'ETATS-UNIS NE PEUT ETRE
U CETTE NORME D'ETATS-UNIS NE PEUT ETR
TERE DE MESURES DE SECURITE CONTRE L'IN
DE MESURES DE SECURITE CONTR
MANUFACTURES, LES SITES ET LES COMMUNA
URES, LES SITES ET LES COMMUN
W565-0155. SUIVEZ LES INSTRUCTIO
65-0155. SUIVEZ LES INSTRUCTIO
01658 (NAC) 4001659 (WUSA)
01658 (NAC) 4001659 (WUSA)
PL
DEL
DEL
GDS20P / CD
S20P / CD
E / ELEVATION
/ ELEVATIO
0-4500FT (0-1
T (0-
/ ALIMENTATION
IMENTATION
20,000 BTU
UT / ALIMENTATION REDUITE 12,000 B
UT / ALIMENTATION REDU
P4 60%
P4
PL
HORIZONTAL VENT
HORIZONTAL VENT
ES AND 20 FEET
S AND 20 FEET
LLATION AND RESEALING IS
D RESEALING IS
TER SERVICING THE VENT-AIR
TER SERVICING THE VENT-A
EM.
EM.
LEARANCE TO COMBUSTIBLE MATERIAL:
EARANCE TO COMBUSTIBLE MATERIAL
4”
2”
C
2”
VENT TOP 2” TO CEILIN
VENT TOP 2” TO
VENT BOTTOM 1” STOVE
VENT BOTTOM 1” ST
V
ENT
S
IDE
S
1
VENT SIDES 1”
UN COMBUST
UN COMBUST
UTILISER AVEC
TILISER AVE
HOMOLOGU
HOMOLOGU
AVERTISS
AVERTIS
AUCUN
AUC
AVEC
AVE
FO
F
For rating plate location, see "INSTALLATION OVERVIEW" section.
This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.
NOTE: The rating plate must remain with the appliance at all times. It must not be removed.
W415-1326 / A / 09.13.17
8
EN
3.0 VENTING
For horizontal runs, both Wolf Steel and Simpon Dura-Vent venting components may have a 0" (0mm) rise per
foot. For optimum performance, it is recommended that all horizontal runs have a minimum 1/4" (6.4mm) rise
per foot.
All inner exhaust and outer intake vent pipe joints may be sealed using either red high temp silicone sealant or
black high temp Mill Pac with the exception of the appliance exhaust ue collar which must be sealed using Mill
Pac (not supplied).
W415-1326 / 05.23.14
8
EN
3.0 VENTING
7.1B
THIS APPLIANCE USES A 4” (102mm) EXHAUST / 7” (178mm) AIR INTAKE VENT PIPE SYSTEM.
Refer to the section applicable to your installation.
For safe and proper operation of the appliance follow the venting instruction exactly. Deviation from the
minimum vertical vent length can create dif culty in burner start-up and/or carboning. Under extreme vent
con gurations, allow several minutes (5-15) for the ame to stabilize after ignition. Provide a means for
visually checking the vent connection to the appliance after the appliance is installed. Use a restop, vent pipe
shield or attic insulation shield when penetrating interior walls, oor or ceiling.
NOTE: If for any reason the vent air intake system is disassembled; reinstall per the instructions
provided for the initial installation.
!
WARNING
RISK OF FIRE, MAINTAIN SPECIFIED AIR SPACE CLEARANCES TO VENT PIPE AND APPLIANCE.
IF VENTING IS INCLUDED WITH SPACERS THE VENT SYSTEM MUST BE SUPPORTED EVERY 3FT
(0.9m) FOR BOTH VERTICAL AND HORIZONTAL RUNS. USE SUPPORTS OR EQUIVALENT
NON-COMBUSTIBLE STRAPPING TO MAINTAIN THE REQUIRED CLEARANCE FROM
COMBUSTIBLES. USE WOLF STEEL LTD. SUPPORT RING ASSEMBLY W010-0370 OR EQUIVALENT
NON-COMBUSTIBLE STRAPPING TO MAINTAIN THE MINIMUM CLEARANCE TO COMBUSTIBLES
FOR BOTH VERTICAL AND HORIZONTAL RUNS. SPACERS ARE ATTACHED TO THE INNER PIPE AT
PREDETERMINED INTERVALS TO MAINTAIN AN EVEN AIR GAP TO THE OUTER PIPE. THIS GAP IS
REQUIRED FOR SAFE OPERATION. A SPACER IS REQUIRED AT THE START, MIDDLE AND END OF
EACH ELBOW TO ENSURE THIS GAP IS MAINTAINED. THESE SPACERS MUST NOT BE REMOVED.
For horizontal runs, both Wolf Steel and Simpon Dura-Vent venting components may have a 0" (0mm) rise per
foot. For optimum performance, it is recommended that all horizontal runs have a minimum 1/4" (6.4mm) rise
per foot.
All inner exhaust and outer intake vent pipe joints may be sealed using either red high temp silicone sealant or
black high temp Mill Pac with the exception of the appliance exhaust ue collar which must be sealed using Mill
Pac (not supplied).
W415-1326 / A / 09.13.17
9
EN
3.1 VENTING LENGTHS AND COMPONENTS
W415-1326 / 05.23.14
9
EN
3.1 VENTING LENGTHS AND COMPONENTS
Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab venting
components. Minimum and maximum vent lengths, for both horizontal and vertical installations, and air terminal
locations for either system are set out in this manual and must be adhered to. For Simpson Dura-Vent, Selkirk
Direct Temp, American Metal Amerivent and Metal-Fab follow the installation procedure provided with the venting
components.
A starter adaptor must be used with the following vent systems and may be purchased from the corresponding
supplier:
* For Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent and Metal-Fab follow the
installation procedure found on the website for your venting supplier.
For vent systems that provide seals on the inner exhaust ue, only the outer air intake joints must be sealed using a
red high temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent
pipe joints of all other approved vent systems except for the exhaust vent pipe connection to the appliance ue collar
which must be sealed using the black high temperature sealant Mill Pac.
When using Wolf Steel venting components, use only approved Wolf Steel termination kits: wall terminal kit GD175
(7/12’ of venting included), or 1/12 to 7/12 pitch roof terminal kit GD110, 8/12 to 12/12 roof terminal kit GD111, at
roof terminal kit GD112 or periscope kit GD180 (for wall penetration below grade) in conjunction with the appropriate
venting components.
For optimum ame appearance and appliance operation, keep the vent length and number of elbows to a
minimum. It is recommended that all horizontal runs have a minimum 1/4” (6.4mm) rise per foot /meter. The
air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify
that it is unobstructed and undamaged. Rigid and exible venting systems must not be combined. Different
venting manufacturers components must not be combined.
These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal
run is 20 feet (6m). The maximum allowable vertical vent length is 40 feet (12m). The maximum number of vent
connections is two horizontally or three vertically (excluding the appliance and the air terminal connections) when
using exible venting.
Deviation from the minimum vertical vent length can create dif culty in burner start-up and/or carboning.
Use an adjustable pipe as the nal length of rigid piping to the stove for ease of installation.
PART 4”/7” (102mm/ 178mm) SUPPLIER WEBSITE
Duravent GDS924N Wolf Steel www.duravent.com
Amerivent 4DSC-N2 American Metal www.americanmetalproducts.com
Direct Temp 4DT-AAN Selkirk www.selkirkcorp.com
SuperSeal 4DNA Metal-Fab www.mtlfab.com
8.5A
W415-1326 / A / 09.13.17
10
EN
3.2 TYPICAL VENT INSTALLATION
W415-1326 / 05.23.14
10
EN
3.2 TYPICAL VENT INSTALLATION
16" (406mm)
MINIMUM
40 FT
(12M)
MAXIMUM
3 FT
(1M)
MINIMUM
25 3/8" (645mm)
25 3/8" (645mm)
MINIMUM
PLUS RISE*
24" (610mm)
MAXIMUM
* See "VENTING" section
W415-1326 / 05.23.14
10
EN
3.2 TYPICAL VENT INSTALLATION
16" (406mm)
MINIMUM
40 FT
(12M)
MAXIMUM
3 FT
(1M)
MINIMUM
25 3/8" (645mm)
25 3/8" (645mm)
MINIMUM
PLUS RISE*
24" (610mm)
MAXIMUM
* See "VENTING" section
(61.0cm)
(64.5cm)
(40.6cm)
(64.5cm)
W415-1326 / A / 09.13.17
11
EN
W415-1326 / 05.23.14
11
EN
3.3 SPECIAL VENT INSTALLATIONS
3.3.1 PERISCOPE TERMINATION
3.3.2 CORNER TERMINATION
The maximum vent length for a corner installation is 24" (610mm) of horizontal run, in addition to the 45° offset.
In this case zero rise is acceptable. See illustrations below. It is recommended to maintain a 6" (152mm) rise.
20” (508mm)
MAXIMUM
24" (610mm)
MAXIMUM
Use the periscope kit to locate the air termination above grade. The periscope must
be installed so that when nal grading is completed, the bottom air slot is located a
minimum of 12” (304.8mm) above grade. The maximum allowable vent length
is 10’ (3.1m) for a replace and 8’ (2.4m) for a stove.
9.5B
12"
(305mm)
MIN TO
GRADE
24" (610mm)
MINIMUM
REGARDLESS
OF HORIZONTAL
VENT LENGTH
25 3/8"
(645mm)
3.3 SPECIAL VENT INSTALLATIONS
3.3.1 PERISCOPE TERMINATION
3.3.2 CORNER TERMINATION
The maximum vent length for a corner installation is 24" (610mm) of horizontal run, in addition to the 45° offset.
In this case zero rise is acceptable. See illustrations below. It is recommended to maintain a 6" (152mm) rise.
24" (610mm)
MAXIMUM
Use the periscope kit to locate the air termination above grade. The periscope must
be installed so that when  nal grading is completed, the bottom air slot is located a
minimum of 12” (304.8mm) above grade. The maximum allowable vent length
is 10’ (3.1m) for a  replace and 8’ (2.4m) for a stove.
9.5B
Added metric dimensions!
12"
(305mm)
MIN TO
GRADE
24" (610mm)
MINIMUM
REGARDLESS
OF HORIZONTAL
VENT LENGTH
25 3/8"
(645mm)
(61.0cm)
(30.5cm)
(64.5cm)
(61.0cm)
W415-1326 / A / 09.13.17
12
EN
3.4 VENT TERMINAL CLEARANCES
W415-1326 / 05.23.14
12
EN
3.4 VENT TERMINAL CLEARANCES
INSTALLATIONS
CANADA U.S.A.
A 12” (305mm) 12” (305mm) Clearance above grade, veranda porch, deck or balcony.
B 12” (305mm)
Δ
9”
(229mm)
Δ
Clearance to windows or doors that open.
C 12” (305mm)* 12” (305mm) * Clearance to permanently closed windows.
D
18”
(457mm)**
18” (457mm)**
Vertical clearance to ventilated sof ts located above the terminal within a horizontal distance of 2’
(0.6m) from the center line of the terminal.
E 12” (305mm)** 12” (305mm)** Clearance to unventilated sof t.
F 0” (0mm) 0” (0mm) Clearance to an outside corner wall.
G
0” (0mm)***
0”
(0mm)***
Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney,
etc.).
2” (51mm)***
2”
(51mm)***
Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase,
etc.).
H 3’(0.9m) 3’ (0.9m)****
Clearance to each side of the center line extended above the meter / regulator assembly to a
maximum vertical distance of 15’ (4.6m).
I 3’ (0.9m) 3’ (0.9m)**** Clearance to a service regulator vent outlet.
J 12” (305mm) 9” (229mm)
Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other
appliance.
K 6’ (1.8m) 3’ (0.9m) † Clearance to a mechanical air supply inlet.
L 7’ (2.1m) ‡ 7’ (2.1m) **** Clearance above a paved sidewalk or paved driveway located on public property.
M
12”
(305mm)††
12”
(305mm)****
Clearance under a veranda, porch or deck.
N 16” (406mm) 16” (406mm) Clearance above the roof.
O 2’ (0.6m)†* 2’ (0.6m) †* Clearance from an adjacent wall including neighbouring buildings.
P 8’ (2.4m) 8’(2.4m) Roof must be non-combustible without openings.
Q 3’ (0.9m) 3’ (0.9m) See chart for wider wall dimensions.
R 6’ (1.8m) 6’ (1.8m)
See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an
opening between the terminal and the open side of the structure.
S 12” (305mm) 12” (305mm) Clearance under a covered balcony
Δ
The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.
* Recommended to prevent condensation on windows and thermal breakage
** It is recommended to use a heat shield and to maximize the distance to vinyl clad sof ts.
*** The periscope requires a minimum 18 inches clearance from an inside corner.
**** This is a recommended distance. For additional requirements check local codes.
3 feet above if within 10 feet horizontally.
A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.
†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the oor.
†* Recommended to prevent recirculation of exhaust products. For additional requirements check local codes.
††* Permitted only if the balcony is fully open on a minimum of one side.
12.1D
NOTE: Clearances are in accordance with local installation codes and the requirements of the gas supplier.
COVERED BALCONY APPLICATIONS ††*
Q
MIN
R
MAX
MAX
R
= 3 feet
(0.9m)
= 2 x
IHHW
(4.6m)
Q
ACTUAL
R
Q
S
G
P
W415-1326 / A / 09.13.17
13
EN
3.5 DEFINITIONS
14.2
For the following symbols used in the venting calculations and examples are:
> - greater than
>
- equal to or greater than
< - less than
<
- equal to or less than
H
T
- total of both horizontal vent lengths (Hr) and offsets (Ho) in feet
H
R
- combined horizontal vent lengths in feet
H
O
- offset factor: .03 (total degrees of offset - 135°*) in feet
V
T
- combined vertical vent lengths in feet
3.6 ELBOW VENT LENGTH VALUES
15.2A
FEET INCHES MILLIMETERS
0.03 0.5 12.7
15° 0.45 6.0 152.4
30° 0.9 11.0 279.4
45°* 1.35 16.0 406.4
90°* 2.7 32.0 812.8
* The fi rst 45° and 90°offset has a zero value and is shown in the formula as -45° and - 90° respectively or
-135° when combined.
W415-1326 / A / 09.13.17
14
EN
3.7 TOP EXIT HORIZONTAL TERMINATION
16.5A
Simple venting confi guration (only one 45° and 90° elbow)
90°
90°
45°
V
1
H
1
H
4
90°
90°
H
3
H
2
V
2
90°
90°
45°
V
1
H
1
H
2
REQUIRED
VERTICAL RISE
IN INCHES
(METERS) V
T
0
5
(1.5)
15
(4.6)
20
(6.1)
100 (2.54)
50 (12.7)
150 (3.81)
12.5
(3.8)
57 (1447.8)
147 (3.73)
10
(3.1)
0
2.5
(0.8)
5
(1.5)
7.5
(2.3)
10
(3.1)
12.5
(3.8)
15
(4.6)
40 (12.2)
10 (3.1)
20 (6.1)
30 (9.1)
17.5
(5.3)
20
(6.1)
39 (11.9)
REQUIRED
VERTICAL
RISE IN FEET
(METERS) V
T
HORIZONTAL VENT RUN PLUS OFFSET IN
FEET (METERS) H
T
HORIZONTAL VENT RUN PLUS
OFFSET IN FEET (METERS) H
T
(H
T
) < (V
T
)
For vent confi gurations requiring more than one 45° elbow and 90° elbow, the following formulas
apply:
Formula 1: H
T
< V
T
Formula 2: H
T
+ V
T
< 40 feet (12.2m)
Example:
V
1
= 8 FT (2.4m)
V
T
= V
1
= 8 FT (2.4m)
H
1
= 2.5 FT (0.8m)
H
2
= 2 FT (0.6m)
H
R
= H
1
+ H
2
= 2.5 FT (0.8m) + 2 FT (0.6m) = 4.5 FT (1.4m)
H
O
= .03 (one 45° elbow + two 90° elbows - 135°) = .03 (225 - 135°) = 2.7 FT (0.8m)
H
T
= H
R
+ H
O
= 4.5 FT (1.4m) + 2.7 FT (0.8m) = 7.2 FT (2.2m)
H
T
+ V
T
= 7.2 FT (2.2m) + 8 FT (2.4m) = 15.2 FT (4.6m)
Formula 1: H
T
< V
T
7.2 FT (2.2m) < 8 FT (2.4m)
Formula 2: H
T
+ V
T
< 40 FT (12.2m)
15.2 FT (4.6m) < 40 FT (12.2m)
Since both formulas are met, this vent confi guration is acceptable.
90°
90°
45°
V
1
H
1
H
4
90°
90°
H
3
H
2
V
2
90°
90°
45°
V
1
H
1
H
2
REQUIRED
VERTICAL RISE
IN INCHES
(METERS) V
T
0
5
(1.5)
15
(4.6)
20
(6.1)
100 (2.54)
50 (12.7)
150 (3.81)
12.5
(3.8)
57 (1447.8)
147 (3.73)
10
(3.1)
0
2.5
(0.8)
5
(1.5)
7.5
(2.3)
10
(3.1)
12.5
(3.8)
15
(4.6)
40 (12.2)
10 (3.1)
20 (6.1)
30 (9.1)
17.5
(5.3)
20
(6.1)
39 (11.9)
REQUIRED
VERTICAL
RISE IN FEET
(METERS) V
T
HORIZONTAL VENT RUN PLUS OFFSET IN
FEET (METERS) H
T
HORIZONTAL VENT RUN PLUS
OFFSET IN FEET (METERS) H
T
90°
90°
45°
V
1
H
1
H
4
90°
90°
H
3
H
2
V
2
90°
90°
45°
V
1
H
1
H
2
REQUIRED
VERTICAL RISE
IN INCHES
(METERS) V
T
0
5
(1.5)
15
(4.6)
20
(6.1)
100 (2.54)
50 (12.7)
150 (3.81)
12.5
(3.8)
57 (1447.8)
147 (3.73)
10
(3.1)
0
2.5
(0.8)
5
(1.5)
7.5
(2.3)
10
(3.1)
12.5
(3.8)
15
(4.6)
40 (12.2)
10 (3.1)
20 (6.1)
30 (9.1)
17.5
(5.3)
20
(6.1)
39 (11.9)
REQUIRED
VERTICAL
RISE IN FEET
(METERS) V
T
HORIZONTAL VENT RUN PLUS OFFSET IN
FEET (METERS) H
T
HORIZONTAL VENT RUN PLUS
OFFSET IN FEET (METERS) H
T
See graph to determine the required vertical
rise V
T
for the required horizontal run H
T
.
The shaded area within the lines represents
acceptable values for H
T
and V
T
W415-1326 / A / 09.13.17
15
EN
16.5_2A
Simple venting confi guration (only one 45° and 90°
elbow)
90°
90°
45°
V
1
H
1
H
4
90°
90°
H
3
H
2
V
2
90°
90°
45°
V
1
H
1
H
2
REQUIRED
VERTICAL RISE
IN INCHES
(METERS) V
T
0
5
(1.5)
15
(4.6)
20
(6.1)
100 (2.54)
50 (12.7)
150 (3.81)
12.5
(3.8)
57 (1447.8)
147 (3.73)
10
(3.1)
0
2.5
(0.8)
5
(1.5)
7.5
(2.3)
10
(3.1)
12.5
(3.8)
15
(4.6)
40 (12.2)
10 (3.1)
20 (6.1)
30 (9.1)
17.5
(5.3)
20
(6.1)
39 (11.9)
REQUIRED
VERTICAL
RISE IN FEET
(METERS) V
T
HORIZONTAL VENT RUN PLUS OFFSET IN
FEET (METERS) H
T
HORIZONTAL VENT RUN PLUS
OFFSET IN FEET (METERS) H
T
(H
T
) > (V
T
)
For vent confi gurations requiring more than one 45° elbow and 90° elbow, the following formulas
apply:
Formula 1: H
T
< 4.2 V
T
Formula 2: H
T
+ V
T
< 24.75 feet (7.5m)
Example:
V
1
= 4 FT (1.2m)
V
2
= 1.5 FT (0.5m)
V
T
= V
1
+ V
2
= 4 FT (1.2m) + 1.5 FT (0.5m) = 5.5 FT (1.7m)
H
1
= 2 FT (0.6m)
H
2
= 1 FT (0.3m)
H
3
= 1 FT (0.3m)
H
4
= 1.5 FT (0.5m)
H
R
= H
1
+ H
2
+ H
3
+ H
4
= 2FT (0.6m) + 1FT (0.3m) + 1FT (0.3m) + 1.5FT (0.5m) = 5.5 FT (1.7m)
H
O
= .03 (one 45° elbow + four 90° elbows - 135°) = .03 (405 - 135°) = 8.1 FT (2.5m)
H
T
= H
R
+ H
O
= 5.5 FT (1.7m) + 8.1 FT (2.5m) = 13.6 FT (4.2m)
H
T
+ V
T
= 13.6 FT (4.2m) + 5.5 FT (1.7m) = 19.1 FT (5.8m)
Formula 1: H
T
< 4.2FT (1.3m) V
T
4.2FT (1.3m) V
T
= 4.2 FT (1.3m) x 5.5 FT (1.7m)= 23.1 FT (7m)
13.6 FT (4.2m) < 23.1 FT (7M)
Formula 2: H
T
+ V
T
< 24.75 FT (7.5m)
19.1 FT (5.8m) < 24.75 FT (7.5m)
Since both formulas are met, this vent confi guration is acceptable.
90°
90°
45°
V
1
H
1
H
4
90°
90°
H
3
H
2
V
2
90°
90°
45°
V
1
H
1
H
2
REQUIRED
VERTICAL RISE
IN INCHES
(METERS) V
T
0
5
(1.5)
15
(4.6)
20
(6.1)
100 (2.54)
50 (12.7)
150 (3.81)
12.5
(3.8)
57 (1447.8)
147 (3.73)
10
(3.1)
0
2.5
(0.8)
5
(1.5)
7.5
(2.3)
10
(3.1)
12.5
(3.8)
15
(4.6)
40 (12.2)
10 (3.1)
20 (6.1)
30 (9.1)
17.5
(5.3)
20
(6.1)
39 (11.9)
REQUIRED
VERTICAL
RISE IN FEET
(METERS) V
T
HORIZONTAL VENT RUN PLUS OFFSET IN
FEET (METERS) H
T
HORIZONTAL VENT RUN PLUS
OFFSET IN FEET (METERS) H
T
90°
90°
45°
V
1
H
1
H
4
90°
90°
H
3
H
2
V
2
90°
90°
45°
V
1
H
1
H
2
REQUIRED
VERTICAL RISE
IN INCHES
(METERS) V
T
0
5
(1.5)
15
(4.6)
20
(6.1)
100 (2.54)
50 (12.7)
150 (3.81)
12.5
(3.8)
57 (1447.8)
147 (3.73)
10
(3.1)
0
2.5
(0.8)
5
(1.5)
7.5
(2.3)
10
(3.1)
12.5
(3.8)
15
(4.6)
40 (12.2)
10 (3.1)
20 (6.1)
30 (9.1)
17.5
(5.3)
20
(6.1)
39 (11.9)
REQUIRED
VERTICAL
RISE IN FEET
(METERS) V
T
HORIZONTAL VENT RUN PLUS OFFSET IN
FEET (METERS) H
T
HORIZONTAL VENT RUN PLUS
OFFSET IN FEET (METERS) H
T
See graph to determine the required vertical
rise V
T
for the required horizontal run H
T
.
The shaded area within the lines represents acceptable values for H
T
and V
T
W415-1326 / A / 09.13.17
16
EN
3.8 VERTICAL TERMINATION
(H
T
) < (V
T
)
Simple venting configurations.
See graph to determine the required vertical rise V
T
for the
required horizontal run H
T
.
REQUIRED
VERTICAL
RISE IN FEET
(METERS) V
T
HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H
T
For vent configurations requiring more than one 45° and one 90° elbow, the following formulas apply:
Formula 1: H
T
< V
T
Formula 2: H
T
+ V
T
< 40 feet (12.2m)
Example:
V
1
= 5 FT (1.5m)
V
2
= 10 FT (3.1m)
V
T
= V
1
+ V
2
= 5 FT (1.5m) + 10 FT (3.1m) = 15 FT (4.6m)
H
1
= 3 FT (0.9m)
H
2
= 2.5 FT (0.8m)
H
R
= H
1
+ H
2
= 3FT (0.9m) + 2.5FT (0.8m) = 5.5 FT (1.7m)
H
O
= .03 (one 45° + three 90° elbows - 135°)
= .03 (45 + 270 - 135°) = 5.4 FT (1.6m)
H
T
= H
R
+ H
O
= 5.5 FT (1.7m)+ 5.4 FT (1.m) = 10.9 FT (3.3m)
H
T
+ V
T
= 10.9 FT (3.3m)+ 15 FT (4.6m) = 25.9 FT (7.9m)
Formula 1: H
T
< V
T
10.9FT (3.3m) < 15 (4.6m)
Formula 2: H
T
+ V
T
< 40 FT (12.2m)
25.9FT (7.9m) < 40 (12.2m)
Since both formulas are met, this vent configuration is acceptable.
The shaded area within the lines represents acceptable
values for H
T
and V
T
0
5
(1.5)
10
(3.1)
15
(4.6)
20
(6.1)
40 (12.2)
10 (3.1)
20 (6.1)
30 (9.1)
3 (0.9)
18.3A
90°
V
1
H
1
H
2
90°
90°
45°
V
2
W415-1326 / A / 09.13.17
17
EN
(H
T
) > (V
T
)
Simple venting configurations.
See graph to determine the required vertical rise V
T
for the
required horizontal run H
T
.
REQUIRED
VERTICAL RISE
IN FEET
(METERS) V
T
HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS)H
T
The shaded area within the lines represents acceptable
values for H
T
and V
T
90°
V
1
H
2
90°
90°
18.3_2B
45°
0
5
(1.5)
10
(3.1)
15
(4.6)
20
(6.1)
10 (3.1)
20 (6.1)
3 (0.9)
25
(7.6)
30
(9.1)
19 (5.8)
V
2
H
1
90°
V
1
H
2
90°
90°
45°
V
2
H
1
45°
H
3
For vent configurations requiring more than one 45° and one 90° elbow, the following formulas apply:
Formula 1:
H
T
< 3V
T
Formula 2:
H
T
+ V
T
< 40 feet (12.2m)
Example:
V
1
= 1 FT (0.3m)
V
2
= 1.5 FT (0.5m)
V
T
= V
1
+ V
2
= 1 FT (0.3m)+ 1.5 FT (0.5m)= 2.5 FT (0.8m)
H
1
= 6 FT (1.8m)
H
2
= 2 FT (0.6m)
H
R
= H
1
+ H
2
= 6FT (1.8m) + 2FT (0.6m) = 8 FT (2.4m)
H
O
= .03 (one 45° + three 90° elbows - 135°)
= .03 (45 + 270 -
135°) = 5.4 FT (1.6m)
H
T
= H
R
+ H
O
= 8FT (2.4m) + 5.4FT (1.6m) = 13.4FT (4.1m)
H
T
+ V
T
= 13.4FT (4.1m)+ 2.5FT (0.8m) = 15.9FT (4.8m)
Formula 1:
H
T
< 3V
T
3V
T
= 3FT (0.9m) x 2.5FT(0.8m) = 7.5FT (2.3m)
13.4 FT (4.1m) > 7.5 FT (2.3m)
Since this formula is not met, this vent configuration is
unacceptable.
Formula 2:
H
T
+ V
T
< 40 FT (12.2m)
15.9FT (4.8m) < 40FT (12.2m)
Since only formula 2 is met, this vent configuration in unacceptable and a new fireplace location or vent
configuration will need to be established to satisfy both formulas.
Example:
V
1
= 1.5 FT (0.5m)
V
2
= 8 FT (2.4m)
V
T
= V
1
+ V
2
= 1.5 FT (0.5m) + 8 FT (2.4m) = 9.5 FT (2.9m)
H
1
= 1 FT (0.3m)
H
2
= 1 FT (0.3m)
H
3
= 10.75 FT (3.3m)
H
R
= H
1
+ H
2
+ H
3
= 1FT(0.3m) + 1FT(0.3m) + 10.75FT(3.3m) = 12.75FT(3.9m)
H
O
= .03 (three 90° elbows + two 45° elbows - 135°)
= .03 (270 + 90 -
135°) = 6.75 FT (2.1m)
H
T
= H
R
+ H
O
= 12.75 FT (3.9m) + 6.75 FT (2.1m) = 19.5 FT (5.9m)
H
T
+ V
T
= 19.5FT (5.9m) + 9.5FT (2.9m) = 29 FT (8.8m)
Formula 1:
H
T
< 3V
T
3V
T
= 3 x 9.5 = 28.5 FT (8.7m)
19.5 FT (5.9m)
< 28.5 (8.7m)
Formula 2:
H
T
+ V
T
< 40 FT (12.2m)
29 FT (8.8m) < 40 FT (12.2m)
Since both formulas are met, this vent configuration is acceptable.
W415-1326 / A / 09.13.17
18
EN
4.0 INSTALLATION
4.1 WALL AND CEILING PROTECTION
For clearances to combustible materials from the vent pipe, see “MINIMUM CLEARANCE TO
COMBUSTIBLES” section.
!
WARNING
DO NOT FILL THE SPACE BETWEEN THE VENT PIPE AND ENCLOSURE WITH ANY TYPE OF
MATERIAL. DO NOT PACK INSULATION OR COMBUSTIBLES BETWEEN CEILING FIRESTOPS.
ALWAYS MAINTAIN SPECIFIED CLEARANCES AROUND VENTING AND FIRESTOP SYSTEMS.
INSTALL WALL SHIELDS AND FIRESTOPS AS SPECIFIED. FAILURE TO KEEP INSULATION OR
OTHER MATERIALS AWAY FROM VENT PIPE MAY CAUSE FIRE.
70.1
W415-1326 / 05.23.14
18
EN
4.0 INSTALLATION
!
WARNING
ENSURE TO UNPACK ALL LOOSE MATERIALS FROM INSIDE THE FIREBOX PRIOR TO HOOKING UP
THE GAS AND ELECTRICAL SUPPLY.
IF YOUR APPLIANCE IS SUPPLIED WITH A REMOTE ENSURE THE REMOTE RECEIVER IS IN THE
“OFF” POSITION PRIOR TO HOOKING UP THE GAS AND ELECTRICAL SUPPLY TO THE APPLIANCE.
FOR SAFE AND PROPER OPERATION OF THE APPLIANCE, FOLLOW THE VENTING INSTRUCTIONS
EXACTLY.
ALL INNER EXHAUST AND OUTER INTAKE VENT PIPE JOINTS MAY BE SEALED USING EITHER RED
RTV HIGH TEMP SILICONE SEALANT W573-0002 (NOT SUPPLIED) OR BLACK HIGH TEMP MILL PAC
W573-0007 (NOT SUPPLIED) WITH THE EXCEPTION OF THE APPLIANCE EXHAUST FLUE COLLAR
WHICH MUST BE SEALED USING MILL PAC.
IF USING PIPE CLAMPS TO CONNECT VENT COMPONENTS, 3 SCREWS MUST ALSO BE USED TO
ENSURE THE CONNECTION CANNOT SLIP OFF.
DO NOT CLAMP THE FLEXIBLE VENT PIPE.
RISK OF FIRE, EXPLOSION OR ASPHYXIATION. IMPROPER SUPPORT OF THE ENTIRE VENTING
SYSTEM MAY ALLOW VENT TO SAG AND SEPARATE. USE VENT RUN SUPPORTS AND CONNECT
VENT SECTIONS PER INSTALLATION INSTRUCTIONS.
RISK OF FIRE, DO NOT ALLOW LOOSE MATERIALS OR INSULATION TO TOUCH THE VENT PIPE.
REMOVE INSULATION TO ALLOW FOR THE INSTALLATION OF THE ATTIC SHIELD AND TO
MAINTAIN CLEARANCES TO COMBUSTIBLES.
68.2B
4.1 WALL AND CEILING PROTECTION
For clearances to combustible materials from the vent pipe, see “MINIMUM CLEARANCE TO
COMBUSTIBLES” section.
!
WARNING
DO NOT FILL THE SPACE BETWEEN THE VENT PIPE AND ENCLOSURE WITH ANY TYPE OF
MATERIAL. DO NOT PACK INSULATION OR COMBUSTIBLES BETWEEN CEILING FIRESTOPS.
ALWAYS MAINTAIN SPECIFIED CLEARANCES AROUND VENTING AND FIRESTOP SYSTEMS.
INSTALL WALL SHIELDS AND FIRESTOPS AS SPECIFIED. FAILURE TO KEEP INSULATION OR
OTHER MATERIALS AWAY FROM VENT PIPE MAY CAUSE FIRE.
70.1
W415-1326 / A / 09.13.17
19
EN
4.1.2 VERTICAL INSTALLATION
4.1.1 HORIZONTAL INSTALLATION
This application occurs when venting through an exterior wall.
Having determined the correct height for the air terminal location, cut
and frame a hole in the exterior wall as illustrated to accommodate
the  restop assembly. Dry  t the  restop assembly before
proceeding to ensure the brackets on the rear surface  t to
the inside surface of the horizontal framing.
The length of the vent shield may be cut shorter
for combustible walls that are less than 8 1/2”
(215.9mm) thick but the vent shield must extend the
full depth of the combustible wall.
A. Assemble the shield to the spacer as
shown, using 3 screws.
B. Place the  restop top so that the vent shield
covers the top of the vent within the opening.
Ensure that both spacer and shield maintain the required
clearance to combustibles.
C. Secure the spacer in place using 4 screws. Once the
vent pipe is installed in its  nal position, apply sealant
between the pipe and the  restop spacer.
DETERMINE
THE
CORRECT
HEIGHT
FIRESTOP
SPACER
VENT
SHIELD
FINISHING
MATERIAL
CAULKING
20.5C
!
WARNING
THE FIRESTOP ASSEMBLY MUST BE INSTALLED WITH THE VENT SHIELD TO THE TOP.
TERMINALS MUST NOT BE RECESSED INTO A WALL OR SIDING MORE THAN THE DEPTH OF THE
RETURN FLANGE OF THE MOUNTING PLATE.
ADD FASTENER TYPE
This application occurs when venting through a roof. Installation kits for
various roof pitches are available from your authorized dealer / distributor.
See accessories to order specifi c kits required.
A. Determine the air terminal location, cut and frame a square opening as
illustrated in the ceiling and the roof to provide the minimum 1" (25mm)
clearance between the vent pipe and any combustible material. Try to
center the vent pipe location midway between two joists to prevent
having to cut them. Use a plumb bob to line up the center of the
openings. A vent pipe shield will prevent any materials such as
insulation, from fi lling up the 1" (25mm) air space around the pipe.
Nail headers between the joist for extra support.
B. Apply a bead of caulking (not supplied) to the framework or to the
Wolf Steel vent pipe shield plate or equivalent (in the case of a fi nished
ceiling), and secure over the opening in the ceiling. A fi restop must be placed
on the bottom of each framed opening in a roof or ceiling that the venting
system passes through. Apply a bead of caulking all around and place a
restop spacer over the vent shield to restrict cold air from being drawn into the
room or around the fi replace. Ensure that both spacer and shield maintain the required
clearance to combustibles. Once the vent pipe is installed in its fi nal position, apply
Mill Pac sealant (W573-0007) (not supplied) or red RTV silicone (W573-0002) (not
supplied) between the pipe and the fi restop assembly.
C. In the attic, slide the vent pipe collar down to cover up the open end of the shield and
tighten. This will prevent any materials, such as insulation, from fi lling up the 1" (25mm)
air space around the pipe.
21.1B
CAULKING
VENT PIPE
SHIELD
FIRESTOP
UNDERSIDE OF
JOIST
VENT
PIPE
COLLAR
VENT
PIPE
SHIELD
W415-1326 / A / 09.13.17
20
EN
TERMINALS MUST NOT BE RECESSED INTO A WALL OR SIDING MORE THAN THE DEPTH OF THE
RETURN FLANGE OF THE MOUNTING PLATE.
DO NOT ALLOW THE INNER FLEX PIPE TO BUNCH UP ON HORIZONTAL OR VERTICAL RUNS AND
ELBOWS. KEEP IT PULLED TIGHT.
!
WARNING
4.2 APPLIANCE VENT CONNECTION
4.3 HORIZONTAL AIR TERMINAL INSTALLATION
W415-1326 / 05.23.14
20
EN
28.5A
A. Attach the adjustable pipe to the last section of rigid pipe. Secure
with screws and seal.
B. Install the inner ex pipe to the appliance. Secure with 3 screws
and at washers. Seal the joint and screw holes using the high
temperature sealant W573-0007 (not supplied).
C. Run a bead of high temperature sealant (not supplied) around the
inside of the air intake collar. Pull the adjustable pipe a minimum 2”
(50.8mm) into the air intake collar.
NOTE: Ensure that the sealant is not visible on the exterior pipes once
installation is completed. An optional decorative black band is available
for this use. In the event that the venting must be disassembled, care
must be taken to reseal the venting.
#8 X 1/2”
SELF
DRILLING
SCREWS
HIGH TEMPERATURE
SEALANT
2” (50.8mm)
OVERLAP
TERMINALS MUST NOT BE RECESSED INTO A WALL OR SIDING MORE THAN THE DEPTH OF THE
RETURN FLANGE OF THE MOUNTING PLATE.
DO NOT ALLOW THE INNER FLEX PIPE TO BUNCH UP ON HORIZONTAL OR VERTICAL RUNS AND
ELBOWS. KEEP IT PULLED TIGHT.
!
WARNING
A. Stretch the inner ex pipe to the required length
taking into account the additional length needed for
the nished wall surface. Apply a heavy bead of the
high temperature sealant W573-0007 Mill Pac (not
supplied) to the inner sleeve of the air terminal. Slip
the vent pipe a minimum of 2” (50.8mm) over the inner
sleeve of the air terminal and secure with 3 #8 screws.
`
B. Using the outer rigid pipe, slide over the outer combustion air
sleeve of the air terminal and secure with 3 #8 screws. Seal
using high temperature sealant W573-0002 (not supplied).
C. Insert the vent pipes through the restop maintaining the required clearance to combustibles. Holding the air
terminal (lettering in an upright, readable position), secure to the exterior wall and make weather tight by sealing
with caulking (not supplied).
D. From inside the house, using silicone, seal between the vent
pipe and the restop. Then slide the black trim collar over the
vent pipe up to the restop.
E. If more vent pipe needs to be used to reach the appliance,
couple them together as illustrated. The vent system must
be supported approximately every 3 feet (0.9m) for both
vertical and horizontal runs. Use noncombustible strapping
to maintain the minimum clearance to combustibles.
The air terminal mounting plate may be recessed into the exterior wall or siding no greater than the depth of its
return ange.
23.7C
SCREWS
#10x2"
SEALANT
HIGH TEMP
2" (50.8mm) OVERLAP
CAULKING
7" (177.8mm) RIGID
PIPE
4" (101.6mm) FLEX PIPE
#8 X 1/2”SELF DRILLING
SCREWS & WASHERS
INNER COUPLER
HI-TEMP
SEALANT
OUTER
RIGID PIPE
INNER
FLEX PIPE
OUTER
RIGID PIPE
4.2 APPLIANCE VENT CONNECTION
4.3 HORIZONTAL AIR TERMINAL INSTALLATION
W415-1326 / 05.23.14
20
EN
28.5A
A. Attach the adjustable pipe to the last section of rigid pipe. Secure
with screws and seal.
B. Install the inner ex pipe to the appliance. Secure with 3 screws
and at washers. Seal the joint and screw holes using the high
temperature sealant W573-0007 (not supplied).
C. Run a bead of high temperature sealant (not supplied) around the
inside of the air intake collar. Pull the adjustable pipe a minimum 2”
(50.8mm) into the air intake collar.
NOTE: Ensure that the sealant is not visible on the exterior pipes once
installation is completed. An optional decorative black band is available
for this use. In the event that the venting must be disassembled, care
must be taken to reseal the venting.
#8 X 1/2”
SELF
DRILLING
SCREWS
HIGH TEMPERATURE
SEALANT
2” (50.8mm)
OVERLAP
TERMINALS MUST NOT BE RECESSED INTO A WALL OR SIDING MORE THAN THE DEPTH OF THE
RETURN FLANGE OF THE MOUNTING PLATE.
DO NOT ALLOW THE INNER FLEX PIPE TO BUNCH UP ON HORIZONTAL OR VERTICAL RUNS AND
ELBOWS. KEEP IT PULLED TIGHT.
!
WARNING
A. Stretch the inner ex pipe to the required length
taking into account the additional length needed for
the nished wall surface. Apply a heavy bead of the
high temperature sealant W573-0007 Mill Pac (not
supplied) to the inner sleeve of the air terminal. Slip
the vent pipe a minimum of 2” (50.8mm) over the inner
sleeve of the air terminal and secure with 3 #8 screws.
`
B. Using the outer rigid pipe, slide over the outer combustion air
sleeve of the air terminal and secure with 3 #8 screws. Seal
using high temperature sealant W573-0002 (not supplied).
C. Insert the vent pipes through the restop maintaining the required clearance to combustibles. Holding the air
terminal (lettering in an upright, readable position), secure to the exterior wall and make weather tight by sealing
with caulking (not supplied).
D. From inside the house, using silicone, seal between the vent
pipe and the restop. Then slide the black trim collar over the
vent pipe up to the restop.
E. If more vent pipe needs to be used to reach the appliance,
couple them together as illustrated. The vent system must
be supported approximately every 3 feet (0.9m) for both
vertical and horizontal runs. Use noncombustible strapping
to maintain the minimum clearance to combustibles.
The air terminal mounting plate may be recessed into the exterior wall or siding no greater than the depth of its
return ange.
23.7C
SCREWS
#10x2"
SEALANT
HIGH TEMP
2" (50.8mm) OVERLAP
CAULKING
7" (177.8mm) RIGID
PIPE
4" (101.6mm) FLEX PIPE
#8 X 1/2”SELF DRILLING
SCREWS & WASHERS
INNER COUPLER
HI-TEMP
SEALANT
OUTER
RIGID PIPE
INNER
FLEX PIPE
OUTER
RIGID PIPE
4.2 APPLIANCE VENT CONNECTION
4.3 HORIZONTAL AIR TERMINAL INSTALLATION
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88

NAPOLEON GDS20 Le manuel du propriétaire

Catégorie
Cheminées
Taper
Le manuel du propriétaire

dans d''autres langues