NAPOLEON GDS50-1PSB Manuel utilisateur

FRENCH

PG. 55

W415-2348 / B / 01.22.20

ADD MANUAL TITLE

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleon.com • [email protected]

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

NATURAL GAS MODELS:

PROPANE GAS MODELS:

Product Name / Code

(MUST use title from Price Book)

ADD ____ ILLUSTRATED

ADD PRODUCT IMAGE

CSA /

INTERTEK

LOGO

SAFETY INFORMATION

- Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the vicinity of

this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the ﬁ re department.

- Installation and service must be

performed by a qualiﬁ ed installer, service

agency, or the supplier.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certiﬁ ed kit is used.

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

WARNING

!

ENGLISH

$10.00

FOR INDOOR USE ONLY

IF INSTALLATION + OPERATION, ADD SERIAL

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE

BARCODE LABEL ON THE OWNER’S MANUAL”

Model GS50 is made up of Model GDS50 and

Natural Vent Adapter Kit GS-150KT

INSTALLATION AND

OPERATION MANUAL

GDS50-1NSB / GDS50-1NE / GS50-1N / GS50-1NE

GDS50-1PSB / GDS50-1PE / GS50-1P / GS50-1PE

Havelock™

(GDS50-1 illustrated)

SAFETY BARRIER

W415-2348 / B / 01.22.20

EN

2

safety information

• This appliance is hot when operated and

can cause severe burns if contacted.

• Any changes or alterations to this

appliance or its controls can be

dangerous and is prohibited.

• Do not operate appliance before reading and

understanding operating instructions. Failure

to operate appliance according to operating

instructions could cause ﬁ re or injury.

• Ensure the glass door is opened or removed

when lighting the pilot for the ﬁ rst time and

when the gas supply has run out.

• Risk of ﬁ re or asphyxiation, do not operate

appliance with ﬁ xed glass removed and never

obstruct the front opening of the appliance.

• Do not connect 110 volts to the control valve,

with the exception of models; GSST8 and

GT8.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves, protective footwear, and safety glasses during

installation. Sheet metal edges may be sharp.

• Do not burn wood or other materials in this appliance.

• Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing

and operating the appliance.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at

test pressures above 1/2 psig. Close the manual shut-off valve before pressure testing gas line at test

pressures equal to or less than 1/2 psig (35mb).

• The appliance must not be operated at temperatures below freezing (32°F / 0°C). Allow the appliance

to warm to above freezing prior to operation, with the exception of models; GSS36, GSS42; these

appliances are suitable for 0°F / -18°C.

• Children and adults should be alerted to hazards of high surface temperature and should stay

away to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the

appliance. Toddlers, young children and others may be susceptible to accidental contact

burns. A physical barrier is recommended if there are at risk individuals in the house. To

restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers,

young children and other at risk individuals out of the room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from

furniture and draperies.

• Furniture or other objects must be kept a minimum of 4 feet (1.22m) away from the front of the appliance.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is off, it will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior

to operating the appliance.

• It is imperative that the control compartments, burners and circulating blower and its passageway in the

appliance and venting system are kept clean. The appliance and its venting system should be inspected

before use and at least annually by a qualiﬁ ed service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and

free from combustible materials, gasoline and other ﬂ ammable vapors and liquids.

• If the appliance shuts off, do not re-light until you provide fresh air. If appliance keeps shutting off, have it

serviced. Keep burner and control compartment clean.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not allow wind or fans to blow directly into the appliance. Avoid any drafts that alter burner ﬂ ame

patterns.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

!

DANGER

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with this appliance and

shall be installed for the protection of children and other

at-risk individuals.

!

WARNING

EN

W415-2348 / B / 01.22.20

3

safety information

!

WARNING

• Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this

appliance.

• This appliance must not be connected to a chimney ﬂ ue pipe serving a separate solid fuel burning

appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system and any gas control which has

been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass

should be done by a licensed or qualiﬁ ed service person, if equipped.

• Do not strike or slam shut the appliance glass door, if equipped.

• Only doors / optional fronts certiﬁ ed with the appliance are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Carbon or soot should not occur in a vent free appliance as it can distribute into the living area of your

home. If you notice any signs of carbon or soot, immediately turn off your appliance and arrange to have

it serviced by a qualiﬁ ed technician before operating it again.

• If equipped, the screen must be in place (closed) when the appliance is in operation.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating

to prevent exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of

the exhaust escaping through these openings can also cause the surrounding combustible materials to

overheat and catch ﬁ re.

• Carbon monoxide poisoning may lead to death; early signs of carbon monoxide poisoning resemble the

ﬂ u, with headache, dizziness and/or nausea. If you have these signs, the appliance may not be working

properly. Get fresh air at once! Have appliance serviced. Some people; pregnant women, persons with

heart or lung disease, anemia, those under the inﬂ uence of alcohol, those at high altitudes are more

affected by carbon monoxide than others. Failure to keep the primary air opening(s) of the burner(s) clean

may result in sooting and property damage.

• As with any combustion appliance, we recommend having your appliance regularly inspected and

serviced as well as having a Carbon Monoxide Detector installed in the same area to defend you and

your family against Carbon Monoxide (not applicable for outdoor appliances).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,

discolouration or damage to decorations, a TV or other electronic components.

• For appliances equipped with a safety barrier; if the barrier becomes damaged, the barrier

shall be replaced with the manufacturer’s barrier for this appliance.

• Installation and repair should be done by a qualiﬁ ed service person. It is imperative that control

compartments, burners and circulating air passageways of the appliance be kept clean.

• For outdoor products only: this appliance must not be installed indoors or within any structure that

prevents or inhibits the exhaust gases from dissipating in the outside atmosphere.

• If applicable, the millivolt version of this appliance uses and requires a fast acting thermocouple. Replace

only with a fast acting thermocouple supplied by Wolf Steel Ltd.

!

WARNING

!

Disconnect the appliance main gas valve/control

from the supply piping when pressure testing that

system at pressures in excess of 1/2 psi (3.5 kPa).

Isolate the appliance with it’s shut off valve during

any pressure testing of the supply piping at

pressures equal to or less than 1/2 psi (3.5 kPa).

FIRE RISK HAZARD / DELAYED IGNITION

High supply pressure will damage the valve / controls.

Add California Prop 65 warning

!

WARNING:

This product can expose you to chemicals including lead and lead compounds,

which are known to the State of California to cause cancer, and chemicals including carbon

monoxide, which are known to the State of California to cause birth defects or other reproduc-

tive harm. For more information, go to www.P65Warnings.ca.gov.

W415-2348 / B / 01.22.20

EN

4

table of contents

1.0 general information 5

1.1 rates and efﬁ ciencies 5

1.2 general instructions 6

1.3 rating plate information 7

1.4 mobile home installation 7

1.5 dimensions 8

2.0 venting 9

2.1 typical vent installation 10

2.2 special vent installations 11

2.2.1 periscope termination 11

2.3 vent terminal clearances 12

2.4 venting application ﬂ ow chart 13

2.5 deﬁ nitions 13

2.6 elbow vent length values 13

2.7 horizontal termination 14

2.8 vertical termination 16

2.9 vertical through existing chimney 18

3.0 installation 19

3.1 minimum clearance to combustibles

19

3.1.1 horizontal installation - GDS50-1 20

3.1.2 vertical installation 20

3.1.3 horizontal air terminal installation 21

3.1.4 vertical air terminal installation 22

3.1.5 appliance vent connection 23

3.2 B-vent installation - GS50-1 23

3.2.1 chimney installation 23

3.2.2 installing ﬂ ashing and storm collar 24

3.2.3 installing natural vent 24

3.2.4 combustion air 24

3.2.6 natural vent adaptations 25

3.2.5 natural vent - model GS50-1 25

3.2.7 adding vent sections 26

4.0 gas installation 27

note:

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves

the right to change or modify any information within this manual at any time without notice. Changes, other than

editorial, are denoted by a vertical line in the margin.

5.0 optional wall switch / remote (millivolt) 27

6.0 finishing 28

6.1 safety barrier and door installation /

removal 28

6.2 log placement 30

6.3 logo placement 31

6.4 trivet installation 31

6.5 control access cover removal /

installation 31

7.0 wiring diagram (electronic) 32

8.0 operation (electronic) 33

8.1 pilot-on-demand 34

9.0 operation (millivolt) 35

10.0 operating instructions 36

10.1 turbo burner operation 36

10.2 spill switch - GS50-1 only 36

11.0 adjustments 37

11.1 pilot burner adjustment 37

11.2 venturi adjustment 37

11.3 ﬂ ame characteristics 38

12.0 maintenance 39

12.1 annual maintenance 39

12.2 replacement blower installation 40

12.3 care of glass 41

12.4 care of plated parts 41

13.0 replacement parts 42

13.1 overview 43

13.2 millivolt valve trian assembly 44

13.3 electronic valve trian assembly 45

14.0 accessories 46

15.0 troubleshooting (millivolt) 47

16.0 troubleshooting (electronic) 49

17.0 warranty 52

18.0 service history 53

EN

W415-2348 / B / 01.22.20

5

standard checklist

1.0 general information

Installer, please ﬁ ll out the following information:

Customer: _____________________________________________________________________

Address: _____________________________________________________________________

Date of Installation: _____________________________________________________________________

Location of Appliance: _____________________________________________________________________

Installer: _____________________________________________________________________

Dealer/Distributor

Contact Number: _____________________________________________________________________

Serial #: _____________________________________________________________________

Model:

Natural Gas: Propane:

GDS50-1NSB

GS50-1N

GDS50-1PSB

GS50-1P

GS50-1 GDS50-1

NG P NG P

Altitude (FT)

0-2000

Max. Input (BTU/HR)

44,000 40,000 44,000 40,000

Max. Output Steady State (BTU/

HR)

31,200 30,000 33,000 30,400

Min. Inlet Gas Supply Pressure

4.5" (11mb)

Water Column

11" (27mb)

Water Column

4.5" (11mb)

Water Column

11" (27mb)

Water Column

Max. Inlet Gas Supply Pressure

7" (17mb)

Water Column *

13" (330.2mm)

Water Column

7" (17mb)

Water Column

13" (330.2mm)

Water Column

Manifold Pressure (Under Flow

Conditions)

3.5" (9mb)

Water Column

10" (25mb)

Water Column

3.5" (9mb)

Water Column

10" (25mb)

Water Column

For elevations between 2,000ft (610m) and 4,500ft (1372m) above sea level, this appliance must be

de-rated by 10% using the certiﬁ ed high altitude kit. When the appliance is installed at elevations above 4,500ft

(1372mm), and in the absence of speciﬁ c recommendations from the local authority having jurisdiction, the

certiﬁ ed high altitude input rating shall be reduced at the rate of 4% for each additional 1,000ft (305m).

Change in ﬂ ame appearance from "HI" to "LO" is more evident in natural gas than in propane. Expansion /

contraction noises during heating up and cooling down cycles are normal and to be expected.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certiﬁ ed kit is used.

Vented decorative gas appliance: not a source of heat; not for use with solid fuel.

GDS50-1: This appliance is approved for bathroom, bedroom and bed-sitting room installations and is suitable for

mobile homes. The natural gas model is suitable for installation in a mobile home that is permanently positioned on

its site and fueled with natural gas.

GS50-1: This appliance is approved for bedroom and bed-sitting room installations.

note:

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the appliance and

must be installed.

* Max. inlet pressure not to exceed 13".

1.1 rates and efﬁ ciencies

GDS50-1NE

GS50-1NE

GDS50-1PE

GS50-1PE

W415-2348 / B / 01.22.20

EN

6

general information

1.2 general instructions

!

WARNING

• Always light the pilot, whether for the ﬁ rst time or if the gas supply has run out, with the glass door opened or

removed.

• Provide adequate clearance for servicing and operating the appliance.

• Provide adequate ventilation.

• Never obstruct the front opening of the appliance.

• Objects placed in front of the appliance must be kept a minimum of 48" (121.9cm) from the front face of the

appliance.

• Surfaces around and especially above the appliance can become hot. Avoid contact when the appliance is

operating.

• Fire risk. Explosion hazard.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at test

pressures above 1/2 PSIG. Close the manual shut-off valve before pressure testing gas line at test pressures

equal to or less than 1/2 PSIG (35mb).

• Use only Wolf Stetel-approved optional accessories and replacement parts with this appliance. Using non-

listed accessories (blowers, doors, louvres, trims, gas components, venting components, etc.) could result in a

safety hazard and will void the warranty and certiﬁ cation.

• The appliance must not be operated at temperatures below freezing (32°F / -°C). Allow the appliance to warm

to above freezing prior to operation.

• This appliance has been designed and certiﬁ ed for indoor use only.

THIS GAS APPLIANCE MUST BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local

codes. Installation practices vary from region to region and it is important to know the speciﬁ cs that apply to your area, for

example in the state of Massachusetts:

• This product must be installed by a licensed plumber or gas ﬁ tter when installed within the commonwealth of

Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of an appliance insert or gas

log.

• The appliance off valve must be a “T” handle gas cock.

• The ﬂ exible connector must not be longer than 36 inches (0.9m).

• A carbon monoxide detector is required in all rooms containing gas ﬁ red appliances.

• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed

combustion product.

The installation must conform with local codes or, in absence of local

codes, the National Gas and Propane Installation Code CSA B149.1

in Canada, or the National Fuel Gas Code, ANSI Z223.1 / NFPA 54

in the United States. Suitable for mobile home installation if installed

in accordance with the current standard CAN/CSA Z240MH Series,

for gas equipped mobile homes, in Canada or ANSI Z223.1 and

NFPA 54 in the United States.

The appliance and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing

of that system at test pressures in excess of 1/2 psig (35 mb).

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any

pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (35 mb). When installed

with a blower or fan, the junction box must be electrically connected and grounded in accordance with local codes. In the

absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI / NFPA 70 National

Electric Code in the United States. In the case where the blower is equipped with a power cord, it must be connected into a

properly grounded receptacle. The grounding prong must not be removed from the cord plug.

The following does not apply to inserts; as long as the required clearance to combustibles is maintained, the most desirable

and beneﬁ cial location for an appliance is in the center of a building, thereby allowing the most efﬁ cient use of the heat

created. The location of windows, doors and, the trafﬁ c ﬂ ow in the room where the appliance is to be located should be

considered. If possible, you should choose a location where the vent will pass through the house without cutting a ﬂ oor or

roof joist. If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood ﬂ ooring, the

appliance shall be installed on a metal or wood panel extending the full width and depth, unless otherwise tested.

We suggest that our gas

hearth products be installed

and serviced by professionals

who are certied in the U.S.

by the National Fireplace

Institute

®

(NFI) as NFI Gas

Specialists

www.ncertied.org

EN

W415-2348 / B / 01.22.20

7

general information

Certiﬁed to Canadian and American National Standards: CSA 2.22-XXXX / ANSI Z21.50-XXXX for Vented Decorative Gas Appliances

Certiﬁé selon les normes Nationales Canadiennes et Américaines: CSA 2.22-XXXX / ANSI Z21.50-XXXX pour les Appareils à gaz décoratif à évacuation

Direct vent, vented gas ﬁreplaces. Approved for bedroom, bathroom and bed-sitting room installation. Suitable for mobile home installation, if installed in accordance with the current

standard CAN / CSA Z240MH Series gas equipped mobile homes in Canada, or, in the United States, the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part

3280. When this US Standard is not applicable, use the Standard for Fire Safety Criteria for Manufactured Home Installations, Sites and Communities, ANSI / NFPA 501A. This appliance

must be installed in accordance with local codes, if any; if none, follow the current ANSI Z223.1 or CSA B149. For use with barrier WXXX-XXXX. Follow installation instructions.

Foyer à gaz ventilé. Homologué pour installation dans une chambre à coucher, une salle de bain et un studio. Approprié pour installation dans une maison mobile si son installation

conforme aux exigences de la norme CAN / CSA Z240MH Séries de maisons mobile équipées au gaz en vigueur au Canada, ou, aux États-Unis selon la norme 24 CFR, Part 3280,

Manufactured Home Construction and Safety Standard. Dans le cas ou cette norme d’États-Unis n’est pas pertinentes, utiliser la norme NFPA 501A, Fire Safety Criteria for Manufactured

Home Installations, Sites and Communities. Installer l’appareil selon les codes ou règlements locaux ou, en l’absence de tels règlements, selon les codes d’installation ANSI Z223.1 ou

CSA B149 en vigueur. Utiliser uniquement avec l’écran WXXX-XXXX. Suivre les instructions d’installation.

9700539 (WSL) 4001658 (NAC) 4001657 (NGZ) 4001659 (WUSA)

WOLF STEEL LTD. 24 Napoleon Road, Barrie, ON, L4M 0G8 Canada

XXXX XXXX XXXX XXXX

MODEL / MODÈLE

Altitude

Input

Reduced Input

P4

Élévation

Alimentation

Alimentation Réduite

P4

Manifold Pressure: 3.5” w.c. (NG)

Minimum Supply Pressure: 4.5” w.c. (NG)

Maximum Supply Pressure: 7”* w.c. (NG)

Pression au Collecteur: 3,5” d’une colonne d’eau (GN)

Pression d’Alimentation Min.: 4,5” d’une colonne d’eau (GN)

Pression d’Alimentation Max.: 7” ** d’une colonne d’eau (GN)

** Maximum inlet pressure not to exceed 13”.

Manifold Pressure: 10” w.c. (P)

Minimum Supply Pressure: 11” w.c. (P)

Maximum Supply Pressure: 13”* w.c. (P)

Pression au Collecteur: 10” d’une colonne d’eau (P)

Pression d’Alimentation Min.: 11” d’une colonne d’eau (P)

Pression d’Alimentation Max.: 13” * d’une colonne d’eau (P)

** Pression d’alimentation maximale ne devait pas dépasser 13”.

0-XXXXft (0-XXXXm)

Minimum clearance to combustible materials:

Top, sides & back: per standoff spacers for framing and ﬁnishing

materials. For non-combustible framing and ﬁnishing materials,

see installation manual.

Top X”

Floor X”

Sides X”

Back X”

Vent top X”

Vent sides & bottom X”

Recessed depth X”

*** Mantel X” from appliance opening

Dégagements minimaux des matériaux combustibles:

Dessus, côtés et arrière: selon les espaceurs de dégagements

pour les matériaux d’ossature selon le manuel du propriétaire

pour les matériaux de ﬁnition.

Dessus X”

Plancher X“

Côtés X”

Arrière X“

Dessus du conduit d’évent X”

Côtés et dessous du conduit d’évent X”

Profondeur d’encastré une face X”

*** Tablette X” de l’ouverture de l’appareil

WARNING: Do not add any material to the appliance which will come in contact with the

ﬂames, other than that supplied by the manufacturer with the appliance.

AVERTISSEMENT: N’ajoutez pas à cet appareil aucun matériau devant entretien

contact avec les ﬂammes autre que celui qui est fourni avec cet appareil par le fabricant.

*** Maximum horizontal extension:

X”. See installation manual for

greater extensions, minimum vent

lengths and maximum vent lengths.

*** L’extension horizontale maximale: X”.

Référez au manuel d’installation pour des

extensions plus grandes, les longueurs

d’évacuation minimaux et maximum.

The appliance must be vented using the appropriate Napoleon vent kits. See installation

manual for venting speciﬁcations. Proper reinstallation and resealing is necessary after servicing

the vent-air intake system.

L’appareil doit être ventilé à l’aide de l’ensemble d’évacuation propre à Napoleon. Référez au

manuel d’installation pour les spéciﬁcations d’évacuation. Il est nécessaire de bien réinstaller et

resceller l’évacuation après avoir executer l’entretien du système de prise d’air.

Serial Number / N° de Série:

W385-XXXX

REFERENCE# 161746

XXXX

VENTED DECORATIVE GAS APPLIANCE: NOT A SOURCE OF

HEAT, NOT INTENDED FOR USE AS A HEATING

APPLIANCE, NOT FOR USE WITH SOLID FUEL.

APPAREIL À GAZ DÉCORATIF À ÉVACUATION: N’EST PAS

UNE SOURCE DE CHALEUR; N’EST PAS DESTINÉ À ÈTRE

UTILISÉ COMME UN APPAREIL DE CHAUFFAGE; NE

CONVIENT PAS AUX COMBUSTIBLES SOLIDES.

FOR USE WITH GLASS DOORS CERTIFIED WITH THIS APPLIANCE ONLY.

POUR UTILISATION UNIQUEMENT AVEC LES PORTES EN VERRE

CERTIFIÉES AVEC L’APPAREIL.

XX,XXX XX,XXX

For natural gas when equipped with No. XX drill size oriﬁce.

For propane when equipped with No. XX drill size oriﬁce.

Convient au gaz naturel quand l’appareil est muni d’un injecteur de diamètre no. XX.

Convient au propane quand l’appareil est muni d’un injecteur de diamètre no. XX.

Electrical rating: 115V, 60HZ. Less than 12 amperes.

Spéciﬁcations électriques: 115V, 60HZ. Moins de 12 ampère.

XX.X% XX.X%

XXXX XXXX XXXX XXXX

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

SAMPLE

appliance ppliance

instructions.uctions.

i son installation on

rme

2

4 CFR

,

Part 3280

,

80,

A, Fire Safety Criteria for Manufactured Fire Safety Criteria for Manufactured

on les codes d’installationdes d’inst

ANSI Z223.1 ou

ou

XXXXXXXX

É

lévation

ation

A

lim

e

nt

a

ti

o

n

Alimentation

A

lim

e

nt

a

ti

o

n R

édu

it

eAlimentation Réduite

P

4

colonne d’eau (GN)colonne d e

.:

4,5” d’une colonne d’eau (GN)4,5” d’une colonne d’eau (GN)

on Max.:

ax.:

7

” ** d’une colonne d’eau

(

GN

)7” ** d’une colonne d’eau (GN)

e not to exceed 13”.

ot to exce

M

an

if

o

ld

P

ressure:

Manifold Pressure:

10” w.c.

(

P

)10” w

M

inimum

S

u

pp

l

y

Pressure:

Minimum Supply Pressure:

11” w.c.

(

P

)11” w.c

M

aximum

S

upply Pressure:

Maximum Supply Pressu

13”* w.c.

(

P

)13”* w.c.

P

ression au

C

ollecteur:

Pression au Collecteur:

10” d’une colonne d’eau (P)10” d’une colonne d’eau

Pr

ess

i

o

n

d

’Alim

e

nt

a

ti

o

n Min.:

ession d’Alimentation M

11” d’une colonne d’eau1” d’une colonne d’e

P

r

ess

i

o

n

d

’Alim

e

nt

a

ti

o

n M

a

x.:

Pression d’Alimentation Max.

13” * d’une colonnd’une c

** Pression d’alimentation maximale ne devait p** Pression d’alimentation maximale ne deva

combustible materials:

mbusti

doff spacers for framing and ﬁnishing

off spacers for framing and ﬁnishing

ble framing and ﬁnishing materials, le framing and ﬁnishing materi

Dégagements minimaux des mDégagements minimaux des

Dessus, côtés et arrière: selonDessus, côtés et arrière: selo

pour les matériaux d’opour les matériaux d

VENTED DECORATIVE GAS APPLIANCE: NOT A SVENTED DECORATIVE GAS APPLIANCE: NOT A S

A

HEAT, NOT INTENDED FOR USE AS A

EAT, NOT INTENDED FOR USE AS A

APPLIANCE, NOT FOR USE WPPLIANCE, NOT FOR USE W

APPAREIL À GAZ DÉCORATIF À ÉVAPPAREIL À GAZ DÉCORATIF À ÉV

UNE SOURCE DE CHALEUUNE SOURCE DE CHALE

UTILISÉ COMMOM

CO

FOR USFOR U

XX,XXXX,XXX

XX.X%XX.X%

XXXXXXXX

M

note:

The rating plate must remain with the appliance at all times. It must not be removed.

1.3 rating plate information

1.4 mobile home installation

This appliance must be installed in accordance with the manufacturer’s instructions and the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home

Standard, CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas

indicated on the rating plate.

This mobile/manufactured home listed appliance comes factory equipped with a means to secure the appliance. Built

in appliances are equipped with 1/4” (6.4mm) diameter holes located in the front left and right corners of the base.

Use appropriate fasteners, inserted through the holes in the base to secure. For free standing products contact your

local authorized dealer / distributor for the appropriate securing kit. For mobile home installations, the appliance must

be fastened in place. It is recommended that the appliance be secured in all installations. Always turn off the pilot and

the fuel supply at the source, prior to moving the mobile home. After moving the mobile home and prior to lighting the

appliance, ensure that the logs are positioned correctly.

This appliance is certiﬁ ed to be installed in an aftermarket permanently located, manufactured (mobile) home,

where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible

for use with other gases, unless a certiﬁ ed kit is used.

Conversion Kits

This appliance is ﬁ eld convertible between Natural Gas (NG) and Propane (P).

To convert from one gas to another, consult your Authorized dealer/distributor.

W415-2348 / B / 01.22.20

EN

8

general information

GAS LINE LOCATED IN PEDESTAL REAR

28 1/4"

718mm

14 1/8"

359mm

21 5/8"

549mm

8"

203mm

7"

178mm

Ø AIR INTAKE

4"

102mm

Ø FLUE

13 3/4"

349mm

21"

533mm

30 3/4"

781mm

SAFETY

BARRIER

2"

51mm

1.5 dimensions

EN

W415-2348 / B / 01.22.20

9

venting

2.0 venting

!

WARNING

• Risk of ﬁ re. Maintain speciﬁ ed air space clearances to vent pipe and appliance.

• The vent system must be supported every 3’(0.9m) for both vertical and horizontal runs. Use support ring assembly W010-

0067 or equivalent non-combustible strapping to maintain the minimum clearance to combustibles for both vertical and

horizontal runs. Spacers are attached to the inner pipe at predetermined intervals to maintain an even air gap to the outer

pipe. This gap is required for safe operation. A spacer is required at the start, middle, and end of each elbow to ensure this

gap is maintained. These spaces must not be removed.

This appliance uses a 4” (102mm) exhaust / 7” (178mm) air intake vent pipe system. Refer to the section applicable

to your installation.

For safe and proper operation of the appliance, follow the venting instructions exactly. Deviation from the minimum vertical

vent length can create difﬁ culty in burner start-up and/or carboning. Under extreme vent conﬁ gurations, allow several minutes

(5-15) for the ﬂ ame to stabilize after ignition. Although not a requirement, it is recommended for vent lengths that pass through

unheated spaces (attics, garages, crawl spaces) be insulated with the insulation wrapped in a protective sleeve to minimize

condensation. Provide a means for visually checking the vent connection to the appliance after the appliance is installed. Use a

ﬁ restop, vent pipe shield or attic insulation shield when penetrating interior walls, ﬂ oor or ceiling.

The vent terminal may be painted with a high temperature paint to match exterior colours. Use an outdoor paint suitable for

400°F (200°C). Application and performance of paint is the consumer’s responsibility. Spot testing is recommended.

Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab venting components.

Minimum and maximum vent lengths, for both horizontal and vertical installations, clearances from vent pipes to combustibles

and air terminal locations as set out in this manual apply to all vent systems and must be adhered to. For Simpson Dura-Vent,

Selkirk Direct Temp, American Metal Amerivent and Metal-Fab, follow the installation procedure provided with the venting

components or on the website for your venting supplier.

A starter adaptor must be used with the following vent systems and may be purchased from the corresponding supplier:

note:

If for any reason the vent air intake system is disassembled, re-install per the instructions provided for the initial installation.

This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing alternate

constructions such as a chimney as part of the vent system is not permitted.

Vent

Manufacturer

Starter Adapter Part Number Supplier Website

Duravent GDS924N Wolf Steel www.duravent.com

Amerivent 4DSC-N2 American Metal www.americanmetalproducts.com

Direct Temp 4DT-AAN Selkirk www.selkirkcorp.com

SuperSeal 4DNA Metal-Fab www.mtlfab.com

For vent systems that provide seals on the inner exhaust ﬂ ue, only the outer air intake joints must be sealed using a red high

temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent pipe joints of all

other approved vent systems except for the exhaust vent pipe connection to the appliance ﬂ ue collar which must be sealed

using the black high temperature sealant Mill Pac. High temperature sealant must be ordered separately.

When using Wolf Steel venting components, use only approved Wolf Steel termination kits: wall terminal kit GD-

175 (7/12" of venting included), or 1/12 to 7/12 pitch roof terminal kit GD-110, 8/12 to 12/12 roof terminal kit GD-

111, ﬂ at roof terminal kit GD-112, or periscope kit GD-180 (for wall penetration below grade) in conjunction with

the appropriate venting components.

For optimum ﬂ ame appearance and appliance performance, keep the vent length and number of elbows to a minimum.

The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that

it is unobstructed and undamaged.

Rigid and ﬂ exible venting systems must not be combined. Different venting manufacturer components must not

be combined.

These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal run is 20

feet (6.1m). The maximum allowable vertical vent length is 40 feet (12.2m). The maximum number of vent connections is two

horizontally or three vertically (excluding the appliance and the air terminal connections) when using ﬂ exible venting.

Horizontal runs may have a 0” rise per foot or 0mm rise per meter however for optimum performance it is recommended

that all horizontal runs have a minimum 1/4” rise per foot or 21mm rise per meter using ﬂ exible venting. For safe and proper

operation of the appliance, follow the venting instructions exactly.

A terminal shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings

and serves both dwellings. Local codes or regulations may require different clearances.

W415-2348 / B / 01.22.20

EN

10

venting

Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼” (31.8mm) air gap

all around between the inner liner and outer liner is required for safe operation.

2.1 typical vent installation

16" (40.6cm)

minimum

40 ft

(12m)

maximum

36" (91.4cm)

minimum

30 3/4"

(78.1cm)

59 3/4"

(151.8cm)

minimum

plus rise*

34" (86.4cm)

maximum

* See "venting" section

29" (73.7cm)

minimum

30 3/4"

(78.1cm)

EN

W415-2348 / B / 01.22.20

11

venting

2.2 special vent installations

2.2.1 periscope termination

Use the periscope kit to locate the air termination above grade. The periscope must be installed so that when

ﬁ nal grading is completed, the bottom air slot is located a minimum 12” (305mm) above grade. The maximum

allowable vent length (including both rise and run) is 10’ (3m) for a ﬁ replace and 8’ (2m) for a stove. An insulation

sleeve is illustrated in the top vent image below, use only when supplied with the appliance.

(The insulation sleeve is not required with a stove appliance)

12" (30.5cm)

Minimum to

Grade

30 3/4"

(78.1cm)

29" (73.7cm)

regardless of horizontal vent length

W415-2348 / B / 01.22.20

EN

12

venting

2.3 vent terminal clearances

Covered balcony applications ††*

Q

MIN

R

MAX

R

= 3 feet

(0.9m)

= 2 x

IHHW

(4.6m)

Q

ACTUAL

R

Q

S

G

P

INSTALLATIONS

CANADA U.S.A.

A

12” (30.5cm) 12” (30.5cm) Clearance above grade, veranda porch, deck or balcony.

B

12” (30.5cm)

Δ

9” (229mm)

Δ

Clearance to windows or doors that open.

C

12” (30.5cm)* 12” (30.5cm)* Clearance to permanently closed windows.

D

18”

(45.7cm)**

18”

(45.7cm)**

Vertical clearance to ventilated sofﬁ ts located above the terminal within a horizontal distance of 2’ (0.6m)

from the center line of the terminal.

E

12” (30.5cm)** 12” (30.5cm)** Clearance to unventilated sofﬁ t.

F

0” (0mm) 0” (0mm) Clearance to an outside corner wall.

G

0” (0mm)*** 0” (0mm)***

Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).

2” (51mm)*** 2” (51mm)*** Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).

H

3’(0.9m) 3’(0.9m)****

Clearance to each side of the center line extended above the meter / regulator assembly to a maximum

vertical distance of 15’ (4.6m).

I

3’ (0.9m) 3’ (0.9m)**** Clearance to a service regulator vent outlet.

J

12” (30.5cm) 9” (229mm) Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.

K

6’ (1.8m) 3’ (0.9m) † Clearance to a mechanical air supply inlet.

L

7’ (2.1m) ‡ 7’ (2.1m) **** Clearance above a paved sidewalk or paved driveway located on public property.

M

12” (30.5cm)†† 12” (30.5cm)**** Clearance under a veranda, porch, deck or overhang.

N

16” (40.6cm) 16” (40.6cm) Clearance above the roof.

O

2’ (0.6m)†* 2’ (0.6m) †* Clearance from an adjacent wall including neighbouring buildings.

P

8’ (2.4m) 8’ (2.4m)

Roof must be non-combustible without openings.

Q

3’ (0.9m) 3’ (0.9m) See chart for wider wall dimensions.

R

6’ (1.8m) 6’ (1.8m)

See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an opening

between the terminal and the open side of the structure.

S

12” (30.5cm) 12” (30.5cm) Clearance under a covered balcony

Δ The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.

* Recommended to prevent condensation on windows and thermal breakage

** It is recommended to use a heat shield and to maximize the distance to vinyl clad sofﬁ ts.

*** The periscope requires a minimum 18 inches clearance from an inside corner.

**** This is a recommended distance. For additional requirements, check local codes.

† 3 feet above if within 10 feet horizontally.

‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.

†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the ﬂ oor.

†* Recommended to prevent recirculation of exhaust products. For additional requirements, check local codes.

††* Permitted only if the balcony is fully open on a minimum of one side.

Clearances are to be in accordance with local

installation codes and the requirements of the gas

supplier. In their absence, clearances are to be as

listed above and are based on national codes.

note:

Wall terminals are for illustration purposes only. Size and

shapes may vary.

EN

W415-2348 / B / 01.22.20

13

venting

2.4 venting application ﬂ ow chart

2.5 deﬁ nitions

2.6 elbow vent length values

Top Exit

Horizontal Termination

Vertical rise is equal

to or greater than the

horizontal run

Vertical rise is equal

to or greater than the

horizontal run

Vertical rise is less

than horizontal run

Vertical rise is less

than horizontal run

Horizontal run +

vertical rise to

maximum of

24.75 feet (7.5m)

Horizontal run +

vertical rise to

maximum of

19 (5.8m)

4.2 times the vertical

rise equal to or

greater than the

horizontal run

3 times the vertical

rise equal to or

greater than the

horizontal run

Horizontal run +

vertical rise to

maximum of

40 feet (12.2m)

Horizontal run +

vertical rise to

maximum of

40 feet (12.2m)

Vertical Termination

For the following symbols used in the venting calculations and

examples are:

> - greater than

> - equal to or greater than

< - less than

< - equal to or less than

H

T

- total of both horizontal vent lengths (Hr) and offsets (Ho) in feet

H

R

- combined horizontal vent lengths in feet

H

O

- offset factor: .03 (total degrees of offset - 90°*) in feet

H

O

- offset factor: .03 (total degrees of offset - 135°*) in feet

V

T

- combined vertical vent lengths in feet

Feet Inches Millimeters

1° 0.03 0.5 12.7

15° 0.45 6.0 152.4

30° 0.9 11.0 279.4

45° 1.35 16.0 406.4

90°* 2.7 32.0 812.8

* The ﬁ rst 90° offset has a zero value and is shown in the formula as - 90°

* The ﬁ rst 45° and° offset have a zero value and is shown in the formula as -45° and -90° respectively

or -135° when combined (for 45° exit only).

W415-2348 / B / 01.22.20

EN

14

venting

2.7 horizontal termination

Simple venting conﬁ guration (only one 90° elbow)

0

2.5

(0.8)

5

(1.5)

7.5

(2.3)

10

(3.1)

12.5

(3.8)

15

(5.6)

40 (12.2)

10 (3.1)

20 (6.1)

30 (9.1)

17.5

(5.3)

20

(6.1)

39 (11.9)

REQUIRED

VERTICAL RISE

IN FEET

(METERS)V

T

HORIZONTAL VENT RUN PLUS OFFSET IN

FEET (METERS) H

T

(H

T

) < (V

T

)

For vent conﬁ gurations requiring more than one 90° elbow, the following formulas apply:

Formula 1: H

T

< V

T

Formula 2: H

T

+ V

T

< 40 feet (12.2m)

Example:

V

1

= 3 FT (0.9m)

V

2

= 8 FT (2.4m)

V

T

= V

1

+ V

2

= 3 FT (0.9m) + 8 FT (2.4m) = 11 FT (3.4m)

H

1

= 2.5 FT (0.8m)

H

2

= 2 FT (0.6m)

H

R

= H

1

+ H

2

= 2.5 FT (0.8m) + 2 FT (0.6m) = 4.5 FT (1.4m)

H

O

= .03 (three 90° elbows - 90°) = .03 (270° - 90°) = 5.4 FT (1.7m)

H

T

= H

R

+ H

O

= 4.5 FT (1.4m) + 5.4 FT (1.7m) = 9.9 FT (3m)

H

T

+ V

T

= 9.9 FT (3m) + 11 FT (3.4m) = 20.9 FT (6.4m)

Formula 1: H

T

< V

T

9.9FT (3m) < 11 FT (3.4m)

Formula 2: H

T

+ V

T

< 40 FT (12.2m)

20.9 FT (6.4m) < 40 FT (12.2m)

Since both formulas are met, this vent conﬁ guration is acceptable.

See graph to determine the required vertical

rise V

T

for the required horizontal run H

T

.

The shaded area within the lines represents

acceptable values for H

T

and V

T

90°

V

1

V

2

H

1

H

2

EN

W415-2348 / B / 01.22.20

15

venting

(H

T

) > (V

T

)

Simple venting configuration (only one 90° elbow)

See graph to determine the required vertical rise V

T

for the

required horizontal run H

T

.

REQUIRED

VERTICAL RISE

IN INCHES

(MILLIMETERS)V

T

For vent configurations requiring more than one 90° elbow, the following formulas apply:

Formula 1:

H

T

< 4.2 V

T

Formula 2: H

T

+ V

T

< 24.75 feet (7.5m)

Example:

V

1

= V

T

= 6 FT (1.8m)

H

1

= 3 FT (0.9m)

H

2

= 5 FT (1.5m)

H

R

= H

1

+ H

2

= 3FT (0.9m + 5FT (1.5m) = 8FT (2.4m)

H

O

= .03 (two 90° elbows - 90°) = .03 (180° - 90°) = 2.7FT (0.8m)

H

T

= H

R

+ H

O

= 8FT (2.4m) + 2.7FT (0.8m) = 10.7FT (3.3m)

H

T

+ V

T

= 10.7FT (3.3m) + 6FT (1.8m) = 16.7FT (5.1m)

Formula 1: H

T

< 4.2 V

T

4.2 V

T

= 4.2FT (1.3m) x 6FT (1.8m) = 25.2 FT (7.7m)

10.7FT (3.3m) < 25.2FT (7.7m)

Formula 2: H

T

+ V

T

< 24.75 FT (7.5m)

16.7FT (5.1m) < 24.75 FT (7.5m)

Since both formulas are met, this vent configuration is acceptable.

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS)H

T

The shaded area within the lines represents acceptable

values for H

T

and V

T

90°

V

1

H

1

H

2

90°

Example:

V

1

= 4 FT (1.2m)

V

2

= 1.5 FT (0.5m)

V

T

= V

1

+ V

2

= 4FT (1.2m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

H

1

= 2 FT (0.6m)

H

2

= 1 FT (0.3m)

H

3

= 1 FT (0.3m)

H

4

= 1.5 FT (0.5m)

H

R

= H

1

+ H

2

+ H

3

+ H

4

= 2FT (0.6m) + 1FT (0.3m) + 1FT (0.3m) + 1.5FT (1.7m) = 5.5 FT (1.7m)

H

O

= .03 (four 90° elbows - 90°) = .03 (360° - 90°) = 8.1 FT (2.5m)

H

T

= H

R

+ H

O

= 5.5FT (1.7m) + 8.1FT (2.5m) = 13.6 FT (4.2m)

H

T

+ V

T

= 13.6 FT (4.2m) + 5.5 FT (1.7m) = 19.1 FT (5.8m)

Formula 1: H

T

< 4.2 V

T

4.2 V

T

= 4.2 FT (1.3m) x 5.5 FT (1.7m) = 23.1 FT (7m)

13.6 FT (4.2m) < 23.1 FT (7m)

Formula 2: H

T

+ V

T

< 24.75 FT (7.5m)

19.1FT (5.8m) < 24.75 FT (7.5m)

Since both formulas are met, this vent configuration is acceptable.

90°

H

1

H

2

V

1

V

2

H

3

H

4

29 (736.6)

0

5

(1.5)

15

(4.6)

20

(6.1)

100 (2540)

50 (1270)

150 (3810)

2.5

(0.8)

10

(3.1)

W415-2348 / B / 01.22.20

EN

16

venting

2.8 vertical termination

(H

T

) < (V

T

)

Simple venting conﬁgurations.

See graph to determine the required vertical rise V

T

for the

required horizontal run H

T

.

REQUIRED

VERTICAL

RISE IN FEET

(METERS) V

T

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

T

For vent conﬁgurations requiring one or more 90° elbows the following formulas apply:

Formula 1: H

T

< V

T

Formula 2: H

T

+ V

T

< 40 feet (12.2m)

Example:

V

1

= 5 FT (1.5m)

V

2

= 6 FT (1.8m)

V

3

= 10 FT (3.1m)

V

T

= V

1

+ V

2

+ V

3

= 5FT (1.5m) + 6FT (1.8m) + 10FT (3.1m) = 21FT (6.4m)

H

1

= 8 FT (2.4m)

H

2

= 2.5 FT (0.8m)

H

R

= H

1

+ H

2

= 8FT (2.4m) + 2.5FT (0.8m) = 10.5 FT (3.2m)

H

O

= .03 (four 90° elbows - 90°)

= .03 (360° - 90°) = 8.1 FT (2.5m)

H

T

= H

R

+ H

O

= 10.5FT (3.2m) + 8.1FT (2.5m) = 18.6FT (5.7m)

H

T

+ V

T

= 18.6FT (5.7m) + 21FT (6.4m) = 39.6FT (12.1m)

Formula 1: H

T

< V

T

18.6FT (5.7m) < 21FT (6.4m)

Formula 2: H

T

+ V

T

< 40 FT (12.19m)

39.6FT (12.1m) < 40FT (12.2m)

Since both formulas are met, this vent conﬁ

g

uration is acce

p

table.

90°

V

1

V

2

H

1

H

2

The shaded area within the lines represents acceptable

values for H

T

and V

T

90°

0

5

(1.5)

10

(3.1)

15

(4.6)

20

(6.1)

40 (12.2)

10 (3.1)

20 (6.1)

30 (9.1)

3 (0.9)

V

3

EN

W415-2348 / B / 01.22.20

17

venting

(H

T

) > (V

T

)

Simple venting conﬁgurations.

See graph to determine the required vertical rise V

T

for the

required horizontal run H

T

.

REQUIRED

VERTICAL

RISE IN FEET

(METERS) V

T

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

T

For vent conﬁgurations requiring more than two 90° elbows the following formulas apply:

Formula 1: H

T

< 3V

T

Formula 2: H

T

+ V

T

< 40 feet (12.2m)

Example:

V

1

= 2 FT (0.6m)

V

2

= 1 FT (0.3m)

V

3

= 1.5 FT (0.5m)

V

T

= V

1

+V

2

+V

3

= 2FT (0.6m) + 1FT (0.3m) + 1.5FT (0.5m) = 4.5FT (1.4m)

H

1

= 6 FT (1.8m)

H

2

= 2 FT (0.6m)

H

R

= H

1

+ H

2

= 6FT (1.8m) + 2FT (0.6m) = 8 FT (2.4m)

H

O

= .03 (four 90° elbows - 90°)

= .03 (360° - 90°) = 8.1 FT (2.5m)

H

T

= H

R

+ H

O

= 8FT (2.4m) + 8.1FT (2.5m) = 16.1FT (4.9m)

H

T

+ V

T

= 16.1FT (4.9m) + 4.5FT (1.4m) = 20.6 FT (6.3m)

Formula 1: H

T

< 3V

T

3V

T

= 3FT (0.9m) x 4.5FT (1.4m) = 13.5FT (4.1m)

16.1FT (4.9m) > 13.5FT (4.1m)

Since this formula is not met, this vent conﬁguration is unacceptable.

Formula 2: H

T

+ V

T

< 40 feet (12.2m)

20.6FT (6.3m) < 40 (12.2m)

Since only formula 2 is met, this vent conﬁguration is unacceptable and a new appliance location or vent conﬁguration

will need to be established to satisf

y

both formulas.

The shaded area within the lines represents acceptable

values for H

T

and V

T

0

5

(1.5)

10

(3.1)

15

(4.6)

20

(6.1)

10 (3.1)

20 (6.1)

3 (0.9)

25

(7.6)

30

(9.1)

19 (5.8)

90°

V

1

V

2

H

1

H

2

90°

V

3

W415-2348 / B / 01.22.20

EN

18

venting

2.9 vertical through existing chimney

!

WARNING

• Risk of ﬁ re.

• Co-axial to co-linear venting conﬁ gurations must only be used in a non-combustible chimney or enclosure.

Installation in a combustible enclosure could result in a ﬁ re.

This appliance is designed to be attached to a 3” (76.2mm) co-linear aluminum ﬂ ex vent system running the full

length of a masonry chimney.

The ﬂ ex liners accommodate any contours of a

masonry chimney, however, it is necessary to keep

the ﬂ exible liners as straight as possible. The inlet

air collar of the termination cap must be connected

to the air intake ﬂ ex liner and the exhaust collar

must be connected to the exhaust ﬂ exible liner.

Both Simpson Duravent and Selkirk co-linear to

co-axial adaptors have been approved on this

appliance

Follow vent manufacturer’s installation instructions.

Different manufacturer’s venting

components must not be combined.

Once the preferred manufacturer’s

appliance adaptor has been attached, the

remainder of the system must be that of

the same manufacturer.

The only exception to this rule is to use

Wolf Steel’s approved 3” (76.2mm) ﬂ ex

liner and co-linear termination.

AIR

INTAKE

EXHAUST

FLUE

FLEX

LINER

* 40 FT (12.2m)

MAX.

10 FT (3.1m)

MIN

COAXIAL TO

CO-LINEAR

ADAPATOR

APPLIANCE

VENT ADAPTOR

TERMINATION

* Measured from appliance ﬂ ue collar

to termination ﬂ ue collar

note:

A vent adaptor will be required directly off the appliance.

EN

W415-2348 / B / 01.22.20

19

installation

All inner exhaust and outer intake vent pipe joints may be sealed using either red high temp silicone sealant or

black high temp Mil Pac with the exception of the appliance exhaust ﬂ ue collar which must be sealed using Mil

Pac (not supplied).

3.0 installation

3.1 minimum clearance to combustibles

As long as clearance to combustibles is kept within required distances, the most desirable and beneﬁ cial location for an appli-

ance is in the centre of a building, thereby allowing the most efﬁ cient use of the heat created. The location of windows, doors and

the trafﬁ c ﬂ ow in the room where the appliance is to be located should be considered. If possible, you should choose a location

where the vent will pass through the house without cutting a ﬂ oor or roof joist.

MAINTAIN THESE MINIMUM CLEARANCES TO COMBUSTIBLES:

A. 7" (17.8mm) B. 2" (51mm) C. 1" (25mm)*

D. 17 1/2" (445mm) E. 6 1/4" (159mm) F. 9 1/2" (241mm)

Minimum 20" (508mm) from appliance top to ceiling

* At a distance of 1" (25mm) from the wall, access to the blower switch, on-off switch or the blower power cord

may not be practical.

GDS50-1:

HORIZONTAL VENT SECTIONS: A minimum clearance of 2" (51mm) at the top and 1" (25mm) at the bottom

and sides of the vent pipe on all horizontal runs is required.

VERTICAL VENT SECTIONS: A minimum of 1" (25mm) all around the vent pipe on all vertical runs to

combustibles is required.

GS50-1:

A minimum of 1" (25mm) all around the B-vent pipe on both horizontal and vertical runs to combustibles is

required.

!

WARNING

• Ensure to unpack all loose materials from inside the ﬁ rebox prior to connecting the gas and electrical supply

• If your appliance is supplied with a remote, ensure the remote receiver is in the “OFF” position prior

to connecting the gas and electrical supply to the appliance.

• For safe and proper operation of the appliance, follow the venting instructions exactly.

• The appliance exhaust ﬂ ue collar must be sealed using Mill Pac. All exhaust and intake vent pipe joints

must be sealed using red RTV high temp silicone sealant (W573-0002) (not supplied) or black high temp Mill

Pac (W573-0007) (not supplied).

• If using pipe clamps to connect rigid vent components, a minimum of 3 screws must also be used to ensure

the connection cannot slip off.

• Do not clamp the ﬂ exible vent pipe.

• Risk of ﬁ re, explosion, or asphyxiation. Improper support of the entire venting system may allow vent to sag

and separate. Use vent run supports and connect vent sections per installation instructions.

• Risk of ﬁ re, do not allow loose materials or insulation to touch the vent pipe. Remove insulation to allow for the

installation of the attic shield and to maintain clearances to combustibles.

• Do not ﬁ ll the space between the vent pipe and enclosure with any type of material. Do not pack insulation

or combustibles between ceiling ﬁ restops. Always maintain speciﬁ ed clearances around venting and ﬁ restop

systems. Install wall shields and ﬁ restops as speciﬁ ed. Failure to keep insulation or other materials away from

vent pipe may cause ﬁ re.

• For gas stoves only: If the appliance is installed directly on carpeting, vinyl tile, or other combustible material

other than wood ﬂ ooring, the appliance shall be installed on a metal or wood panel extending the full width and

depth, unless otherwise tested.

E

B

A

D

B

A

45°

C

F

SIDE WALL

BACK WALL

SIDE WALL

BACK WALL

ALCOVE

W415-2348 / B / 01.22.20

EN

20

installation

3.1.1 horizontal installation - GDS50-1

This application occurs when venting through an exterior

wall. Having determined the correct height for the air

terminal location, cut and frame a hole in the exterior wall,

as illustrated, to accommodate the ﬁ restop assembly. Dry

ﬁ t the ﬁ restop assembly before proceeding to ensure the

brackets on the rear surface ﬁ t to the inside surface of the

horizontal framing.

The length of the vent shield may be cut shorter for

combustible walls that are less than 8 1/2” (215.9mm)

thick but the vent shield must extend the full depth of the

combustible wall.

A. Assemble the shield to the spacer as shown, using the 3

shorter screws supplied.

B. Place the ﬁ restop top so that the vent shield covers the top of

the vent within the opening. Ensure that both spacer and shield

maintain the required clearance to combustibles.

C. Secure the spacer in place using the 4 longer screws supplied.

Once the vent pipe is installed in its ﬁ nal position, apply sealant between the pipe and the ﬁ restop spacer.

• The ﬁ restop assembly must be installed with the vent shield to the top.

• Terminals must not be recessed into a wall or siding more than the depth of the return ﬂ ange of the mounting

plate.

!

WARNING

Do not ﬁ ll the air space between the ﬁ restop spacer and the

exterior wall with any type of insulating material (i.e. spray foam).

note:

DETERMINE

THE

CORRECT

HEIGHT

CAULKING

FIRESTOP

SPACER

VENT

SHIELD

FINISHING

MATERIAL

CAULKING

note:

The above is for illustration purposes only. Vents

do not always pass through center of frame.

ADD

WIDTH

ADD

HEIGHT

10 11/16"

(27.1cm)

10 11/16"

(27.1cm)

3.1.2 vertical installation

This application occurs when venting through a roof. Installation kits for

various roof pitches are available from your authorized dealer / distributor.

See the “accessories” section to order speciﬁ c kits required.

A. Determine the air terminal location, cut and frame a square opening,

as illustrated, in the ceiling and the roof to provide the minimum 1"

(25mm) clearance between the vent pipe and any combustible material.

Try to center the vent pipe location midway between two joists to

prevent having to cut them. Use a plumb bob to line up the center of

the openings. A vent pipe shield will prevent any materials such as

insulation, from ﬁ lling up the 1" (25mm) air space around the pipe. Nail

headers between the joist for extra support.

B. Apply a bead of caulking (not supplied) to the framework or to the

Wolf Steel vent pipe shield plate or equivalent (in the case of a ﬁ nished

ceiling), and secure over the opening in the ceiling. A ﬁ restop must be

placed on the bottom of each framed opening in a roof or ceiling that

the venting system passes through. Apply a bead of caulking all around

and place a ﬁ restop spacer over the vent shield to restrict cold air from

being drawn into the room or around the ﬁ replace. Ensure that both

spacer and shield maintain the required clearance to combustibles.

Once the vent pipe is installed in its ﬁ nal position, apply red RTV

silicone (W573-0002) (not supplied) between the pipe and the ﬁ restop

assembly.

C. In the attic, slide the vent pipe collar down to cover up the open end

of the shield and tighten. This will prevent any materials, such as

insulation, from ﬁ lling up the 1" (25mm) air space around the pipe.

Caulking

Vent Pipe

Shield

Vent

Pipe

Shield

Vent

Pipe

Collar

Firestop

underside

of joist

La page est en cours de chargement...

NAPOLEON GDS50-1PSB Manuel utilisateur

NAPOLEON GDS50-1PSB Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents