Wacker Neuson DF 16 Manuel utilisateur

Operator's manual

Notice d'emploi

Ligatureur d'armatures

DF 16

Rebar tier

50000193482 06 0811

50000193482

EN-FR

Manufacturer

Wacker Neuson Produktion GmbH & Co. KG

Preußenstraße 41

80809 München

www.wackerneuson.com

Tel.: +49-(0)89-354 02-0

Fax: +49-(0)89-354 02-390

Translation of the original operator's manual in German

08.2011

0214885en / 006

DF 16 Contents

Operator's manual 3

1 Foreword ....................................................................................................................5

2 Introduction ...............................................................................................................6

2.1 Means of representation for this operator's manual ........................................... 6

2.2 Wacker Neuson representative .......................................................................... 7

2.3 Described machine types ................................................................................... 7

2.4 Identification of the machine............................................................................... 8

3 Safety .........................................................................................................................9

3.1 Principle.............................................................................................................. 9

3.2 Qualification of the operating personnel........................................................... 12

3.3 Transport .......................................................................................................... 12

3.4 Operating safety ............................................................................................... 13

3.5 Safety during the operation of hand machines................................................. 14

3.6 Maintenance..................................................................................................... 14

4 Scope of delivery ....................................................................................................15

5 Structure and function ...........................................................................................16

5.1 Application........................................................................................................ 16

5.2 Field of application............................................................................................ 16

5.3 Functionality ..................................................................................................... 16

6 Components and operator's controls ...................................................................17

7 Transport .................................................................................................................18

8 Use and operation ...................................................................................................19

8.1 Prior to starting the machine............................................................................. 20

8.2 Starting up ........................................................................................................ 23

8.3 Operating the machine ..................................................................................... 26

8.4 Avoiding faulty ties............................................................................................ 27

8.5 Removing jammed ties..................................................................................... 31

9 Troubleshooting ......................................................................................................34

10 Maintenance ............................................................................................................35

10.1 Maintenance schedule...................................................................................... 35

10.2 Maintenance work ............................................................................................ 36

10.2.1 Cleaning machine................................................................................. 36

10.2.2 Oiling the spindle.................................................................................. 37

10.2.3 Greasing the folding mechanism of the twisting hook .......................... 38

10.2.4 Greasing the fixing spring..................................................................... 40

Contents

Contents DF 16

4 Operator's manual

10.2.5 Thorough cleaning of the machine ....................................................... 41

11 Accessories .............................................................................................................42

11.1 Tie strip............................................................................................................. 42

11.2 Carrying case ................................................................................................... 42

11.3 Copper grease.................................................................................................. 42

11.4 Belt pouch ........................................................................................................ 42

12 Technical data .........................................................................................................43

12.1 DF 16................................................................................................................ 43

1 Foreword

5

1Foreword

This operator's manual contains information and procedures for the safe opera-

tion and maintenance of your Wacker Neuson machine. In the interest of your

own safety and to prevent accidents, you should carefully read through the safety

information, familiarize yourself with it and observe it at all times.

This operator's manual is not a manual for extensive maintenance and repair

work. Such work should be carried out by Wacker Neuson service or authorized

specialists.

The safety of the operator was one of the most important aspects taken into con-

sideration when this machine was designed. Nevertheless, improper use or in-

correct maintenance can pose a risk. Please operate and maintain your Wacker

Neuson machine in accordance with the instructions in this operator's manual.

Your reward will be troublefree operation and a high degree of availability.

Defective machine parts must be replaced immediately!

Please contact your Wacker Neuson representative if you have any questions

concerning operation or maintenance.

No part of this publication may be reproduced in any form or by any means, elec-

tronic or mechanical, including photocopying, without the expressed written per-

mission of Wacker Neuson.

Any type of reproduction, distribution or storage on data media of any type and

form not authorized by Wacker Neuson represents an infringement of copyright

and will be prosecuted.

We expressly reserve the right to make technical modifications – even without

special notice – which aim at further improving our machines or their safety stan-

dards.

2 Introduction

6

2 Introduction

2.1 Means of representation for this operator's manual

Warning symbols

This operator's manual contains safety information of the categories:

DANGER, WARNING, CAUTION, NOTICE.

They should be followed to prevent danger to life and limb of the operator or dam-

age to equipment and exclude improper service.

Notes

Note: Complementary information will be displayed here.

DANGER

This warning notice indicates immediate hazards that result in serious injury or

even death.

f Danger can be avoided by the following the actions mentioned.

WARNING

This warning notice indicates possible hazards that can result in serious injury

or even death.

f Danger can be avoided by the following the actions mentioned.

CAUTION

This warning notice indicates possible hazards that can result in minor injury.

f Danger can be avoided by the following the actions mentioned.

NOTICE

This warning notice indicates possible hazards that can result in material dam-

age.

f Danger can be avoided by the following the actions mentioned.

2 Introduction

7

Instructions

f This symbol indicates there is something for you to do.

1. Numbered instructions indicate that you have to carry out something in a defined

sequence.

 This symbol is used for lists.

2.2 Wacker Neuson representative

Depending on your country, your Wacker Neuson representative is your Wacker

Neuson service, your Wacker Neuson affiliate or your Wacker Neuson dealer.

You can find the addresses in the Internet at www.wackerneuson.com.

The address of the manufacturer is located at the beginning of this operator's

manual.

2.3 Described machine types

This operator's manual is valid for different machine types from a product range.

Therefore some figures can differ from the actual appearance of your machine.

It is also possible that the descriptions include components which are not a part

of your machine.

Details for the described machine types can be found in the chapter Technical

data.

2 Introduction

8

2.4 Identification of the machine

Nameplate data

The nameplate lists information that uniquely identifies your machine. This infor-

mation is needed to order spare parts and when requesting additional technical

information.

f Enter the information of your machine into the following table:

Item Designation Your information

1 Group and type

2 Construction year

3 Machine no.

4 Version no.

5 Item no.

DF 16 3 Safety

Operator's manual 9

3Safety

3.1 Principle

State of the art

This machine has been constructed with state-of-the-art technology according to

the recognized rules of safety. Nevertheless, when used improperly, dangers to

the life and limb of the operator or to third persons or damage to the machine or

other materials cannot be excluded.

Proper use

The machine was designed to tie together reinforced steel rods prior to their use

in concrete.

The machine must only be used for tying together the following materials:

 Reinforcing steel rods.

 Water hoses which are suitable for and have been approved for concrete

core activation.

 Conduits for electrical installations which are suitable and approved for at-

tachment to reinforcements.

The sum of the diameters of the materials which are to be connected to each oth-

er must not exceed a maximum value, see chapter Technical data.

The machine may only be operated using ties made by Wacker Neuson.

In particular, the machine must not be used for tying the following materials:

 Electrical cables.

 Gas lines.

Its proper use also includes the observance of all instructions contained in this

operator's manual as well as complying with the required service and mainte-

nance instructions.

Any other use is regarded as improper. Any damage resulting from improper use

will void the warranty and the liability on behalf of the manufacturer. The operator

assumes full responsibility.

3 Safety DF 16

10 Operator's manual

Structural modifications

Never attempt to modify the machine without the written permission of the man-

ufacturer. To do so will endanger your safety and the safety of other people! In

addition, this will void the warranty and the liability on behalf of the manufacturer.

Especially the following are cases of structural modifications:

 Opening the machine and the permanent removal of components from

Wacker Neuson.

 Installing new components which are not from Wacker Neuson and not equiv-

alent to the original parts in design and quality.

 Installation of accessories which are not from Wacker Neuson.

It is no problem to install spare parts from Wacker Neuson.

It is no problem to install accessories that are available in the Wacker Neuson

product range of your machine. Please refer to the installation regulations in this

operator's manual.

Requirements for operation

The ability to operate the machine safely requires:

 Proper transport, storage and setup.

 Careful operation.

 Careful service and maintenance.

Operation

Operate the machine only as intended and only when in proper working condi-

tion.

Maintenance

Regular maintenance is required in order for the machine to operate properly and

reliably over time. Failure to perform adequate maintenance reduces the safety

of the machine.

 Strictly observe the prescribed maintenance intervals.

 Do not use the machine if it requires maintenance or repairs.

Malfunctions

If a malfunction occurs, the machine must be secured immediately.

Eliminate the malfunctions that impair safety immediately!

Have damaged or defective components replaced immediately!

For further information, refer to chapter Troubleshooting.

DF 16 3 Safety

Operator's manual 11

Spare parts, accessories

Use only spare parts from Wacker Neuson or such that are equivalent to the orig-

inal parts in design and quality.

Only use accessories from Wacker Neuson.

Non-compliance will exempt the manufacturer from all liability.

Exclusion of liability

Wacker Neuson will refuse to accept liability for injuries to persons or for damage

to materials in the following cases:

 Structural modifications.

 Improper use.

 Failure to comply with this operator's manual.

 Improper handling.

 Using of spare parts which are not from Wacker Neuson and not equivalent

to the original parts in design and quality.

 Using of accessories which are not from Wacker Neuson.

 Using ties which are not from Wacker Neuson.

Operator's manual

Always keep the operator's manual near the machine or near the worksite for

quick reference.

If you have misplaced the operator's manual or require an additional copy, con-

tact your Wacker Neuson representative or download the operator's manual from

the Internet (www.wackerneuson.com).

Always hand over this operator's manual to other operators or to the future owner

of the machine.

Country-specific regulations

Observe the country-specific regulations, standards and guidelines in reference

to accident prevention and environmental safety, for example those pertaining to

hazardous materials and wearing protective gear.

Complement the operator's manual with additional instructions taking into ac-

count the operational, regulatory, national or generally applicable safety guide-

lines.

Operator's controls

Always keep the operator's controls of the machine dry, clean and free of oil or

grease.

The function of the operator's controls must not be manipulated or rendered in-

effective.

3 Safety DF 16

12 Operator's manual

Checking for signs of damage

Inspect the machine when it is switched off for any signs of damage at least once

per work shift.

Do not operate the machine if there is visible damage or defects.

Have any damage or defects eliminated immediately.

3.2 Qualification of the operating personnel

Operator qualifications

Only trained personnel must operate the machine.

Incorrect operation

Incorrect operation or misuse by untrained personnel can endanger the health

and safety of the operator or third persons and also cause machine and material

damage.

Operating company responsibilities

The operating company must make the operator's manual available to the oper-

ator and ensure that the operator has read and understood it.

Work recommendations

Please observe the recommendations below:

 Work only if you are in a good physical condition.

 Work attentively, particularly as you finish.

 Do not operate the machine when you are tired.

 Carry out all work calmly, circumspectly and carefully.

 Never operate the machine under the influence of alcohol, drugs or medica-

tion. This can impair your vision, reactions and your judgment.

 Work in a manner that does not endanger others.

3.3 Transport

Transporting the machine

Transport the machine in the carrying case supplied.

Secure the carrying case on the transport device against tilting, falling and slip-

ping.

DF 16 3 Safety

Operator's manual 13

3.4 Operating safety

Work environment

Familiarize yourself with your work environment before you start work. This in-

cludes e.g. the following items:

 Obstacles in the work and traffic area.

 Load-carrying capacity of the ground.

 The measures needed to cordon off the construction site from public traffic.

 The measures needed to secure walls and ceilings.

 Options available in the event of an accident.

Vertical stability

Always make sure that you stand firmly when working with the machine. This ap-

plies particularly when working on scaffoldings, ladders, etc.

3 Safety DF 16

14 Operator's manual

Operating the machine

Always place the machine onto the reinforced steel rods at an exact right angle.

Work using even push and pull movements (do not push or pull abruptly).

Always continue the push and pull movements up to the stop.

Do not direct towards people

Do not direct the machine towards people in the vicinity during oepration. Insert-

ed components might be flung out and cause serious injuries.

Storage

Set the machine down or store it securely so that it cannot tilt, fall down or slip.

Storage location

Store the machine after operation at a sealed off, clean and dry location inacces-

sible to children.

3.5 Safety during the operation of hand machines

Setting the hand machine down properly

Set the machine down carefully. Do not drop the machine to the floor or from

greater heights. Dropping the machine can cause injuries to other persons or the

machine itself can be damaged.

3.6 Maintenance

Maintenance work

Service and maintenance work must only be carried out to the extent described

in these operating instructions. All other procedures must be performed by your

Wacker Neuson representative.

For further information, refer to chapter Maintenance.

Cleaning

Always keep the machine clean and be sure to clean it each time you have fin-

ished using it.

Do not use gasoline or solvents. Danger of explosion!

Do not use high pressure washers. Permeating water can damage the machine.

When electrical equipment is present, this can pose a serious injury risk from

electric shocks.

DF 16 4 Scope of delivery

Operator's manual 15

4 Scope of delivery

Item Designation

1 Rebar tier

2 Tube of copper grease (without

illustration)

3 Operator's Manual (without illus-

tration)

4 Spare parts catalog (without illus-

tration)

5 Structure and function DF 16

16 Operator's manual

5 Structure and function

5.1 Application

Use the machine only as intended, see chapter Safety, Proper use.

5.2 Field of application

You can work with the machine in a horizontal or in a vertical direction, on ceil-

ings and on walls.

The machine can be used in all weather conditions.

5.3 Functionality

Principle

The tool is a manually operated rebar tier. The machine can be operated single-

handed.

After placement onto the reinforced steel rods the handle is moved forward up to

the stop. This causes a feed device to transport a tie in an arc shape around the

reinforced steel rods. At the end point of the forward movement the tie tabs in-

terlock automatically.

When the handle is pulled back the arc shaped tie is twisted. The fully twisted tie

automatically triggers the unlocking of the twisting hook.

After the twisting spindle is moved back the machine is ready for the next tying

operation.

DF 16 6 Components and operator's controls

Operator's manual 17

6 Components and operator's controls

Item Designation Item Designation Item Designation

1 Tie outlet 6 Lock 11 Twisting hook

2 Cover 7 Housing floor 12 Unlock mechanism at the

twisting hook

3 Handle 8 Tie strip 13 Tie

4 Gripper clamp 9 Feed finger 14 Tie tab with guide pin

5 Umbrella handle 10 Magazine tensioner

7 Transport DF 16

18 Operator's manual

7 Transport

Transporting the machine

The machine must be transported in the carrying case supplied.

1. Push umbrella handle in completely, see Adjusting the length of the umbrella

handle (page 21).

2. Push the handle completely forwards.

3. If necessary, remove tie, see Removing jammed ties from the outside

(page 31).

4. Place the machine on or into a suitable means of transport.

5. Secure the machine against falling or sliding.

DF 16 8 Use and operation

Operator's manual 19

8 Use and operation

WARNING

Spring-loaded moving components.

Serious injuries or property damage from improper handling.

f When the machine is open, secure the magazine tensioner in the park or

stop position.

NOTICE

Machine malfunction due to damaged components within the machine.

f Always store the machine and tie strip under dry conditions.

f Protect the tie strip against excessive heat and cold.

f Do not use corroded ties.

f Dry machines which have become wet.

8 Use and operation DF 16

20 Operator's manual

8.1 Prior to starting the machine

Turning the umbrella handle

For ties which are rotated by 45° from the direction of movement of the operator,

you can turn the umbrella handle for easier handling.

1. Release the Allen screw on the gripper clamp.

2. Turn the umbrella handle into the position required.

3. Retighten the Allen screw manually.

Item Designation

1 Gripper clamp

2 Umbrella handle

3Allen screw

La page charge ...

Wacker Neuson DF 16 Manuel utilisateur

Wacker Neuson DF 16 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents