Wacker Neuson RCP-16/120 60 Hz Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

Cutting machine
Cisaille
RCP
12, 16, 32
Notice d'emploi
Operator's manual
5000193483 04 0811
5000193483
EN-FR
Manufacturer
Wacker Neuson Produktion GmbH & Co. KG
Preußenstraße 41
80809 München
www.wackerneuson.com
Tel.: +49-(0)89-354 02-0
Fax: +49-(0)89-354 02-390
Translation of the original operator's manual in German
0215050en 004
08.2011
RCP 12, 16, 32
Operator’s manual 3
Contents
1 Foreword ....................................................................................................................5
2 Introduction ...............................................................................................................6
2.1 Means of representation for this operator's manual ........................................... 6
2.2 Wacker Neuson representative .......................................................................... 7
2.3 Described machine types ................................................................................... 7
2.4 Identification of the machine............................................................................... 8
3 Safety .........................................................................................................................9
3.1 Principle.............................................................................................................. 9
3.2 Qualification of the operating personnel........................................................... 12
3.3 Protective gear ................................................................................................. 13
3.4 Transport .......................................................................................................... 14
3.5 Operating safety ............................................................................................... 14
3.6 Safety during the operation of hand machines................................................. 16
3.7 Safety during the operation of electric appliances............................................ 16
3.8 Safety during the operation of hydraulic machines........................................... 18
3.9 Maintenance..................................................................................................... 18
3.10 Safety and information labels ........................................................................... 19
3.11 Safety devices .................................................................................................. 20
4 Scope of delivery ....................................................................................................21
5 Description ..............................................................................................................22
5.1 Application........................................................................................................ 22
5.2 Functionality ..................................................................................................... 22
5.3 Components and operator's controls................................................................ 23
6 Transport .................................................................................................................26
7 Operation .................................................................................................................27
7.1 Prior to starting the machine............................................................................. 27
7.2 Adjusting the machine ...................................................................................... 28
7.3 Starting up ........................................................................................................ 31
7.4 Decomissioning ................................................................................................ 35
8 Maintenance ............................................................................................................36
8.1 Maintenance schedule...................................................................................... 36
8.2 Maintenance work ............................................................................................ 37
8.2.1 Visual inspection for damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8.2.2 Changing the knife on the RCP-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8.2.3 Changing the knife on the RCP-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
RCP 12, 16, 32
4 Operator’s manual
8.2.4 Changing the knife on the RCP-32. . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8.2.5 Adjusting the stroke for RCP-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
8.2.6 Adjusting the stroke for RCP-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
8.2.7 Checking the hydraulic oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
8.2.8 Changing the hydraulic oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
9 Troubleshooting ...................................................................................................... 55
10 Disposal ...................................................................................................................56
10.1 Disposal of waste electrical and electronic equipment..................................... 56
11 Accessories ............................................................................................................. 57
12 Technical data ......................................................................................................... 58
12.1 RCP-12/16/32 - 230 ......................................................................................... 58
12.2 RCP-12/16/32 - 115 ......................................................................................... 59
12.3 RCP-12/16/32 - 120 ......................................................................................... 60
12.4 Extension cable ................................................................................................ 61
13 Glossary ...................................................................................................................65
EC Declaration of Conformity ................................................................................ 67
1 Foreword
5
1Foreword
This operator's manual contains information and procedures for the safe opera-
tion and maintenance of your Wacker Neuson machine. In the interest of your
own safety and to prevent accidents, you should carefully read through the safety
information, familiarize yourself with it and observe it at all times.
This operator's manual is not a manual for extensive maintenance and repair
work. Such work should be carried out by Wacker Neuson service or authorized
specialists.
The safety of the operator was one of the most important aspects taken into con-
sideration when this machine was designed. Nevertheless, improper use or in-
correct maintenance can pose a risk. Please operate and maintain your Wacker
Neuson machine in accordance with the instructions in this operator's manual.
Your reward will be troublefree operation and a high degree of availability.
Defective machine parts must be replaced immediately!
Please contact your Wacker Neuson representative if you have any questions
concerning operation or maintenance.
All rights reserved, especially reproduction and distribution rights.
Copyright 2011 Wacker Neuson Produktion GmbH & Co. KG
No part of this publication may be reproduced in any form or by any means, elec-
tronic or mechanical, including photocopying, without the expressed written per-
mission of Wacker Neuson.
Any type of reproduction, distribution or storage on data media of any type and
form not authorized by Wacker Neuson represents an infringement of copyright
and will be prosecuted.
We expressly reserve the right to make technical modifications – even without
special notice – which aim at further improving our machines or their safety stan-
dards.
2 Introduction
6
2 Introduction
2.1 Means of representation for this operator's manual
Warning symbols
This operator's manual contains safety information of the categories:
DANGER, WARNING, CAUTION, NOTICE.
They should be followed to prevent danger to life and limb of the operator or dam-
age to equipment and exclude improper service.
Notes
Note: Complementary information will be displayed here.
DANGER
This warning notice indicates immediate hazards that result in serious injury or
even death.
f Danger can be avoided by the following the actions mentioned.
WARNING
This warning notice indicates possible hazards that can result in serious injury
or even death.
f Danger can be avoided by the following the actions mentioned.
CAUTION
This warning notice indicates possible hazards that can result in minor injury.
f Danger can be avoided by the following the actions mentioned.
NOTICE
This warning notice indicates possible hazards that can result in material dam-
age.
f Danger can be avoided by the following the actions mentioned.
2 Introduction
7
Instructions
f This symbol indicates there is something for you to do.
1. Numbered instructions indicate that you have to carry out something in a defined
sequence.
This symbol is used for lists.
2.2 Wacker Neuson representative
Depending on your country, your Wacker Neuson representative is your Wacker
Neuson service, your Wacker Neuson affiliate or your Wacker Neuson dealer.
You can find the addresses in the Internet at www.wackerneuson.com.
The address of the manufacturer is located at the beginning of this operator's
manual.
2.3 Described machine types
This operator's manual is valid for different machine types from a product range.
Therefore some figures can differ from the actual appearance of your machine.
It is also possible that the descriptions include components which are not a part
of your machine.
Details for the described machine types can be found in the chapter Technical
data.
2 Introduction
8
2.4 Identification of the machine
Nameplate data
The nameplate lists information that uniquely identifies your machine. This infor-
mation is needed to order spare parts and when requesting additional technical
information.
f Enter the information of your machine into the following table:
Item Designation Your information
1 Group and type
2 Construction year
3 Machine no.
4 Version no.
5 Item no.
3 Safety
Operator's manual 9
3Safety
3.1 Principle
State of the art
This machine has been constructed with state-of-the-art technology according to
the recognized rules of safety. Nevertheless, when used improperly, dangers to
the life and limb of the operator or to third persons or damage to the machine or
other materials cannot be excluded.
Proper use
The machine may only be used for cutting reinforcing steel.
The diameter and tensile strength of the reinforcing steel that may be processed
with the machine are dependent on the machine design. Please refer to the
chapter Technical Data for information concerning your machine.
Worksites are construction sites and operations which fabricate reinforcements
or process reinforcing iron. The machine may only be used for legal and permit-
ted purposes.
The machine must not be used for processing the following materials:
Wires
Pipes
Plastics
Wood
Its proper use also includes the observance of all instructions contained in this
operator's manual as well as complying with the required service and mainte-
nance instructions.
Any other use is regarded as improper. Any damage resulting from improper use
will void the warranty and the liability on behalf of the manufacturer. The operator
assumes full responsibility.
3 Safety
10 Operator's manual
Structural modifications
Never attempt to modify the machine without the written permission of the man-
ufacturer. To do so will endanger your safety and the safety of other people! In
addition, this will void the warranty and the liability on behalf of the manufacturer.
Especially the following are cases of structural modifications:
Opening the machine and the permanent removal of components from
Wacker Neuson.
Installing new components which are not from Wacker Neuson and not equiv-
alent to the original parts in design and quality.
Installation of accessories which are not from Wacker Neuson.
It is no problem to install spare parts from Wacker Neuson.
It is no problem to install accessories that are available in the Wacker Neuson
product range of your machine. Please refer to the installation regulations in this
operator's manual.
Do not drill into the housing, e.g. to install signs. Water could penetrate the hous-
ing and damage the machine.
Requirements for operation
The ability to operate the machine safely requires:
Proper transport, storage and setup.
Careful operation.
Careful service and maintenance.
Operation
Operate the machine only as intended and only when in proper working condi-
tion.
Operate the machine in a safety-conscious manner with all safety devices at-
tached and enabled. Do not modify or disable any safety devices.
Before starting operation, check that all control and safety devices are function-
ing properly.
Never operate the machine in a potentially explosive environment.
Supervision
Never leave the machine running unattended!
3 Safety
Operator's manual 11
Maintenance
Regular maintenance work is required in order for the machine to operate prop-
erly and reliably over time. Failure to perform adequate maintenance reduces the
safety of the machine.
Strictly observe the prescribed maintenance intervals.
Do not use the machine if it requires maintenance or repairs.
Malfunctions
If you detect a malfunction, you must shut down and secure the machine imme-
diately.
Eliminate the malfunctions that impair safety immediately!
Have damaged or defective components replaced immediately!
For further information, refer to chapter Troubleshooting.
Spare parts, accessories
Use only spare parts from Wacker Neuson or such that are equivalent to the orig-
inal parts in design and quality.
Only use accessories from Wacker Neuson.
Non-compliance will exempt the manufacturer from all liability.
Exclusion of liability
Wacker Neuson will refuse to accept liability for injuries to persons or for damage
to materials in the following cases:
Structural modifications.
Improper use.
Failure to comply with this operator's manual.
Improper handling.
Using of spare parts which are not from Wacker Neuson and not equivalent
to the original parts in design and quality.
Using of accessories which are not from Wacker Neuson.
Operator's manual
Always keep the operator's manual near the machine or near the worksite for
quick reference.
If you have misplaced the operator's manual or require an additional copy, con-
tact your Wacker Neuson representative or download the operator's manual from
the Internet (www.wackerneuson.com).
Always hand over this operator's manual to other operators or to the future owner
of the machine.
3 Safety
12 Operator's manual
Country-specific regulations
Observe the country-specific regulations, standards and guidelines in reference
to accident prevention and environmental safety, for example those pertaining to
hazardous materials and wearing protective gear.
Complement the operator's manual with additional instructions taking into ac-
count the operational, regulatory, national or generally applicable safety guide-
lines.
Operator's controls
Always keep the operator's controls of the machine dry, clean and free of oil or
grease.
Operating elements such as ON/OFF switch, gas handles etc. may not be
locked, manipulated or changed without authorization.
Checking for signs of damage
Inspect the machine when it is switched off for any signs of damage at least once
per work shift.
Do not operate the machine if there is visible damage or defects.
Have any damage or defects eliminated immediately.
3.2 Qualification of the operating personnel
Operator qualifications
Only trained personnel are permitted to start and operate the machine. The fol-
lowing rules also apply:
You are physically and mentally fit.
You have received instruction on how to independently operate the machine.
You have received instruction in the proper use of the machine.
You are familiar with required safety devices.
You are authorized to start machines and systems in accordance with the
standards governing safety.
Your company or the operator has assigned you to work independently with
this machine.
Incorrect operation
Incorrect operation or misuse by untrained personnel can endanger the health
and safety of the operator or third persons and also cause machine and material
damage.
3 Safety
Operator's manual 13
Operating company responsibilities
The operating company must make the operator's manual available to the oper-
ator and ensure that the operator has read and understood it.
Work recommendations
Please observe the recommendations below:
Work only if you are in a good physical condition.
Work attentively, particularly as you finish.
Do not operate the machine when you are tired.
Carry out all work calmly, circumspectly and carefully.
Never operate the machine under the influence of alcohol, drugs or medica-
tion. This can impair your vision, reactions and your judgment.
Work in a manner that does not endanger others.
Ensure that no persons or animals are within the danger zone.
3.3 Protective gear
Work clothing
Clothing should be appropriate, i.e. should be close-fitting but not restrict your
movement.
When on construction sites, do not wear long hair loosely, loose clothing or jew-
elry including rings. These objects can easily get caught or be drawn in by mov-
ing machine parts.
Only wear clothing made of material that is not easily flammable.
Personal protective gear
Wear personal protective gear to avoid injuries or health hazards:
Non-skid, hard-toed shoes.
Work gloves made of durable material.
Overalls made of durable material.
Hard hat.
Ear protection.
Face protection.
Eye protection.
Breathing protection in the case of dusty ambient air.
3 Safety
14 Operator's manual
3.4 Transport
Switching off the machine
Before you transport the machine, switch it off and pull the plug out of the plug
receptacle. Allow the motor to cool down.
Transporting the machine
Transport the machine in the carrying case supplied.
Secure the carrying case on the transport device against tilting, falling or slipping.
Lifting the machine
A falling machine can cause serious injuries.
The machine has no lifting or lashing points.
When lifting the machine, secure it in a closed transport container or similar in
order to prevent it from toppling, falling or slipping away.
Restarting
Machines, machine parts, accessories or tools that were detached for transport
purposes must be re-mounted and fastened before restarting.
Only operate in accordance with the operating instructions.
3.5 Operating safety
Explosible environment
Never operate the machine in a potentially explosive environment.
Work environment
Familiarize yourself with your work environment before you start work. This in-
cludes e.g. the following items:
Obstacles in the work and traffic area.
Load-bearing capacity of the ground.
The measures needed to cordon off the construction site from public traffic in
particular.
The measures needed to secure walls and ceilings.
Options available in the event of an accident.
3 Safety
Operator's manual 15
Safety in the work area
When working with the machine especially pay attention to the following points:
Electric lines or pipes in work area.
Gas lines or water lines in the work area.
Checks before starting work
Check the following points before beginning work:
Condition of tools.
Machine settings.
Connection value of the machine.
Starting the machine
Observe the safety information and warning notices located on the machine and
in the operator's manual.
Never attempt to start a machine that requires maintenance or repairs.
Start the machine as described in the operator's manual.
Vertical stability
Always make sure that you stand firmly when working with the machine. This ap-
plies particularly when working on scaffoldings, ladders, uneven or slippery
floors etc.
Caution with movable parts
Keep your hands, feet and loose clothing away from moving machine parts.
No persons endangered
Be sure that no persons are endangered by flying or falling materials. Always
work very attentively, and anticipate potential hazards.
Switching off the machine
Switch off the machine and pull the plug out of the plug receptacle in the following
situations:
Before breaks.
If you are not using the machine.
If you are changing the tool.
Before storing the machine, wait until it has completely stopped running.
Store the machine or put it down in such a way that it cannot tilt, fall down or slip.
Storage
Set the machine down or store it securely so that it cannot tilt, fall down or slip.
3 Safety
16 Operator's manual
Storage location
After operation, allow the machine to cool and then store it in a sealed-off, clean
and dry location protected against frost and inaccessible to children.
3.6 Safety during the operation of hand machines
Safe working with hand machines
Secure loose workpieces with suitable methods.
While working, as a rule hold the machine on the provided handles with both
hands.
3.7 Safety during the operation of electric appliances
Specific regulations for electrical appliances
Observe the safety information provided in the brochure General Safety Rules
which is included in the scope of delivery of your machine.
Also observe the country-specific regulations, standards and guidelines in refer-
ence to accident prevention in connection with electrical equipment and ma-
chines.
WARNING Read all safety information and instructions. Failure to follow
the safety information and instructions may result in electric shock, fire and/or se-
rious injury.
Save all safety information and instructions for future reference.
3 Safety
Operator's manual 17
Electric power supply for electrical appliances of class rating II
Note: The rated voltage is indicated on the nameplate of your machine.
The machine may only be connected to an electric power supply with all machine
parts in proper working condition. Take special notice of the following compo-
nents:
Plug.
Power cable over the entire length.
Switch diaphragm of the ON/OFF switch, if there is one.
Plug receptacles.
Electrical appliances of class rating II have a strengthened or double insulation
(protective insulation). They have no connection to the grounded conductor.
There must be at least one of the following safety devices if connected to a sta-
tionary or mobile generator:
Fault current protective switch.
Isolation (earth leakage) monitor.
IT-net.
Note: Observe the respective national safety regulations!
Extension cable
The machine may only be operated with undamaged and tested extension ca-
bles!
Only use extension cables with grounded conductor and correct connection of
the grounded conductor to the plug and coupling (only for machines of class rat-
ing I, see chapter Technical data).
Only use tested extension cables which are suitable for use at construction sites:
Average rubber hose H05RN-F or better – Wacker Neuson recommends
H07RN-F, an SOOW cable, or a country-specific equivalent design.
Immediately replace damaged extension cables (e.g. tears in the sheathing) or
loose plugs and couplings.
Cable drums and multiple plug receptacles must fulfill the same requirements as
the extension cable.
Protect extension cables, multiple plug receptacles, cable drums and connection
couplings against rain, snow or any other forms of moisture.
Uncoil the cable drum completely
Danger of fire due to wound cable drum.
Uncoil the cable drum completely before operation.
3 Safety
18 Operator's manual
Protecting the power cable
Do not use the power cable to pull or lift the machine.
Do not unplug the power cable by pulling on the cable.
Protect the power cable from heat, oil and sharp edges.
If the power cable is damaged or the plug is loose, have it replaced immediately
by your Wacker Neuson representative.
Protecting from moisture
Protect the machine against rain, snow or any other forms of moisture. This could
cause damage or other malfunctions.
Protecting against extreme high or low temperatures
Do not expose the machine to extreme high or low temperatures. Otherwise the
insulation current conducting parts can be damaged.
Information on the permissible temperature range can be found in the chapter
Technical Data.
3.8 Safety during the operation of hydraulic machines
Hydraulic oil
Hydraulic oil is harmful to health.
Wear safety glasses and safety gloves when handling hydraulic oil.
Avoid direct skin contact with hydraulic oil. Remove hydraulic oil from the skin im-
mediately with soap and water.
Make sure that no hydraulic oil comes gets in the eyes or on the body. See a phy-
sician immediately if hydraulic oil gets into the eyes or is swallowed.
Do not eat and drink while handling hydraulic oil.
Make sure to have extreme cleanliness. Contamination of the hydraulic oil with
dirt or water can cause premature wear or failure of the machine.
Dispose of left over and spilled hydraulic oil according to the applicable regula-
tions for environmental protection.
3.9 Maintenance
Maintenance work
Service and maintenance work must only be carried out to the extent described
in these operating instructions. All other procedures must be performed by your
Wacker Neuson representative.
For further information, refer to chapter Maintenance.
3 Safety
Operator's manual 19
Disconnecting the machine from the electric power supply
Before carrying out service or maintenance work, pull the plug out of the plug re-
ceptacle in order to disconnect the machine from the electric power supply.
Cleaning
Always keep the machine clean and be sure to clean it each time you have fin-
ished using it.
Do not use gasoline or solvents. Danger of explosion!
Do not use high pressure washers. Permeating water can damage the machine.
When electrical equipment is present, this can pose a serious injury risk from
electric shocks.
3.10 Safety and information labels
Your machine has adhesive labels containing the most important instructions
and safety information.
Make sure that all the labels are kept legible.
Replace any missing or illegible labels.
The item numbers for the labels are in the parts book.
Label Description
Wear safety glasses.
Wear hard hat.
Follow operator's manual.
Wear ear protection.
Wear protective gloves.
Wear non-skid, hard-toed shoes.
Max. workpiece diameter.
Only use hydraulic oil of type HLP-ISO-46 (e.g. ESSO
NUTO H46), refer to chapter Technical data.
WARNING
Danger due to cutting.
WARNING
Flying chips.
Warm up machine at temperatures under 5 °C.
3 Safety
20 Operator's manual
3.11 Safety devices
Protective hood
A protective hood is installed for some machine designs.
WARNING
Danger of injury due to open moving parts.
f Only operate the machine with properly installed and functioning safety de-
vices.
f Do not modify or remove safety devices.
Item Designation
1 Protective hood
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140

Wacker Neuson RCP-16/120 60 Hz Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues