Ducati PRO-I PLUS Manuel utilisateur

Marque: Ducati

Modèle: PRO-I PLUS

Taper: Manuel utilisateur

Electric Scooter

User Manual

Electric Scooter

English

1. Scooter

2. Manual

3. Accessories:

- Allen key

- n° 4 screws

- Spare inner tube

- Spare Stickers

- Tyre inflation adapter

4. Battery charger

1. Product and Accessories

Electric Scooter

User Manual

2. Diagram Functions

Control panel

Brake

Front Light Accelerator

Folding

mechanism

Motor

Charging port

Kickstand

Disc brake

Brake light

Folding closure

Battery

Motor Fault

Velocity indicator

Cruise Control

Power ON/OFF Button

Speed Mode

Battery indicator

Front light

 1. Power on: Press Power on button for 3 seconds.

 2. Power off: Press Power off button for 3 seconds.

 3. How to turn on/off light: After power on the e-scooter, press the power on/off

button for 1 second, front light is turned on. Press again to turn off.

 4. Brake: e-brake+disc brake, when brake, the rear light will be flashing.

 5. How to change speed?: After power on, default is the lower speed. Switch the speed

by quick pressing two times the power On/off button within 1 second.

 7. Low voltage warning mode: Under this mode, the speed limitness is 7Km/h.

 8. Auto Cruise: Speed Cruise activated automatically after same speed for 10 seconds,

then you can release the speed controller; press brake controller or press again the speed

controller, scooter returns back to manual mode.

 9. Speed Setting:

Level 1: <= 6 km/h

Level 2: <= 20 km/h

Level 3: > 20 km/h

 10. Auto Power off: After 10mins without any operation, it will be powered off automati-

cally.

 6. Battery indicator

33v-36v One battery bar light

36v-37v Two battery bar light

37v-38.5v Three battery bar light

38.5v o superiore All battery bar light

Low voltage warning: the 1st battery bar flashing once voltage is lower than 33V, buzzer

warning for 6 times in the same time.

Function Fault:

Fault Code

E.1

E.2

E.4

E.5

E.6

E.7

E.8

Instruction

E-accelerator fault

Battery voltage over 42V

Output Current exceeds 14A

Brake failure

Motor Hall wire fault

Motor stuck

Motor phase line fault

E.3

Battery voltage below 32V

3. Assembly

1. Lock the column

and open the closure

at the base.

2.Install the handlebar/-

control panel on the

column.

3. Use the screws and

Allen key provided to

secure the handlebar.

4. After finishing, turn on

the device to make sure

everything works.

1 2 3



4. Recharging

1. Open the rubber cap.

2. Insert the charger plug.

3. When the battery is full,remove the charger and

close the rubber cap.

The red light on the power supply will turn green when charging is complete.

There is a risk of falling while using the device. We therefore recommend the use of a

protective helmet and appropriate equipment.

� Turn on the device and check the battery charge level.

� Place one foot on the footboard, keeping the other foot on the ground.

� Gently press the accelerator, and when the device has reached a constant speed, place

the other foot on the platform as well.

� To slow down, release the throttle button. For stronger braking, use the brake lever on

the left.

� To turn or change direction, tilt slightly to the right or left and gently rotate the handle-

bar. Turn on the device and check the level battery.

6. Safety Standards

� Avoid driving in the rain.

� Slow down on bumpy roads, sidewalks or other special road surfaces. On very uneven

roads, please maintain a low speed (between 3,11 and 6,21 mph at most). Remaining flexi-

ble on the knees makes it easier to adapt to bumpy roads.

� Pay attention to doors or other obstacles in height.

� Do not accelerate downhill.

� Do not press the accelerator when walking beside the vehicle.

� Pay attention to possible obstacles during the use of the device.

� Drive calmly and concentrate, do not do stunts with the device.

� Do not drive on the road.

� Do not change direction abruptly at high speed.

� Do not drive on water, mud or snow.

� Do not climb on the device with a child.

� It is forbidden to position yourself and concentrate your weight on the rear fender.

� Do not touch the disc brake

� Do not let go of the handlebar while driving.

� Do not jump over obstacles and do not walk down stairs with the device. There is a risk

of accidents and damage to the vehicle.

� This device is for recreational purposes and is not intended as a passenger vehicle. Any

vehicle travelling in public places is risky and potentially dangerous. Please strictly follow

the instructions in this manual to guide the device in respect of your own safety and that

of others. It is also mandatory to comply with local and national laws for the use of this

device.

� You should be aware that when pedaling in a public area you are subject to strict rules

but also to the risk of falls, collisions with pedestrians or other vehicles. As with other

vehicles, the higher the speed, the longer the braking time. Emergency braking on a

smooth surface can cause the device to slip, resulting in falls and injuries. It is therefore

very important to adapt driving style and speed and to maintain an adequate safety

distance from pedestrians or other means of transport.

� Please respect pedestrians when driving the device. Avoid frightening pedestrians,

especially children and the elderly. When overtaking a pedestrian, it is a good idea to slow

down and pass as far away as possible.

� The safety instructions in this manual must be strictly followed. The company cannot be

held responsible for any injury or accident if the instructions are not followed.

� Do not lend the device to anyone who has not been trained to use it and who is not

wearing the appropriate protective equipment.

� Always check the device before use, if you notice that any parts are damaged, that the

battery has a very low charging capacity, that the tires are worn or inflated abnormally, or

that there is a strange noise or malfunction please do not use the device and contact an

authorized repairer.



Closing Opening

� Switch off the appliance, open the locking system by turning the locking lever, bend the

body of the scooter and attach the column lock to the mudguard lock.

� Make sure that the locks are locked correctly.

� To open the device, press the hook located on the column, then lift it up and lower the

locking lever again.

Transport position

Always carry your scooter with one or both hands from the handlebar stem.

8. Maintenance

Cleaning and storage:

� To clean the device it is necessary to use a soft and slightly damp cloth. If cleaning is

more difficult than expected, you can use a toothbrush for stubborn dirt.

Caution: Do not use alcohol, petrol or other solvents, corrosive chemicals, otherwise the

device may be damaged both in appearance and structure. Do not use high-pressure

guns to clean the device. In general, when cleaning the device, make sure that it is

switched off, that the charger cable is disconnected and that the rubber cover is closed.

When not in use, store the device in a dry place away from moisture. Do not store the

device outdoors. Excessive exposure to the sun, heat or cold can damage the device and

accelerate tire and battery wear.

In case of punctures, contact your tyre specialist.

For information, technical support and assistance, please visit www.argentobike.it

Battery maintenance:

� Do not use batteries other than the original model.

� Do not touch the battery contacts and do not open the battery compartment. Do not

place metal objects in contact with the battery. This may cause short circuits and damage

the battery, or even injure or kill the user.

� Only use the original charger. A different charger may damage the device or cause a fire.

� Do not dispose of the battery in the household garbage. Follow local environmental

regulations on recharging the battery after each use of the device will prolong its

strength and performance.

� Do not use the battery in extreme environments (-20° C; +50° C), as this may cause the

battery to malfunction and even cause a fire hazard.

� Do not expose the battery to the sun for too long (e. g. , in the trunk of a car) and do not

throw it into a fire, as this may cause an explosion.

� It is necessary to fully charge the battery every two months to prevent it from compro-

mising. If you do not charge the battery for more than 4 months, the battery may be

irreversibly damaged.

� Only authorized repairers may change the battery. Don't do it if you're not a professional.

Brake adjustment

� If the brake is too tight, use the supplied key and turn it counterclockwise to release

the brake cable pressure, then shorten the cable and tighten with the key. If the

brake is too slow, do the opposite and extend the brake cable.

Shaky direction column

� If the handlebar is wobbly, you can tighten the screws on the bending system using

the supplied Allen key.



� If the device tires are deflated, you can use the valves to inflate them with a car tires

pump or inflation system.

Brake cable

9. Technical Specifications

Index Details

Size

Main specifications

Battery specifications

Motor specifications

Battery charger

specifications

L × P × A

When folded: L × P × A

Maximum load

Driving requirements

Minimum age

Minimum height

Maximum speed

Autonomy

Climbing angle

Operating temperature

Storage temperature

IP rating

Surfaces suitable for driving

Charging

Capacity

Intelligent battery

management system

Rated input voltage

Rated output voltage

Output current

Power

Regular power

Maximum power

Recharge time

Parameters

108×43×114cm

108×43×49cm

100Kg

20 - 25Km

15%

36V

-10°C / +50°C

-20°C /+55°C

42V max

7800mAh

250W

500W

Abnormal temperature management, short

circuit, automatic back-up, overvoltage, double

overload, double protection.

110-210V

42V

1.7A

71W

16 years old

120cm

IP54

Cement, asphalt and muddy roads; platforms

less than 0.39in; surfaces with cracks less than

1.18in wide.

25Km/h (

(varies according to soil and weight)

~5h

Article weight

12Kg

Weight

Treatment of the electrical or electronic device at the end of its life (applicable in all

           

collection system)

In particular, consumers are obliged not to dispose of WEEE as municipal waste, but

must participate in the separate collection of this type of waste through two modes

of delivery:

1. at municipal collection centers (also known as recycling depot), directly or through

municipal collection services, where these are available;

2. at the point of sale of new electrical and electronic equipment. Here you can deliv-

er very small WEEE free of charge (with the longest side less than 9,84in), while

larger WEEE can be delivered in 1-on-1 mode, i. e. by delivering the old product when

you buy a new one with the same functions.

In case of illegal disposal of electrical or electro-nickel equipment, the sanctions

provided for by the current legislation on environmental protection may be applied

(valid only for Italy).

Where WEEE contains batteries or accumulators, these must be removed and

subject to specific separate collection.

This symbol on the product or on the packaging indicates that

the product should not be considered as normal household

waste, but should instead be delivered to a collection point

approved for the recycling of electrical and electronic equipment

(WEEE).

By ensuring that this product is disposed of properly, you will

help prevent potential negative consequences for the environ-

ment and health that might otherwise be caused by its improper

disposal. Recycling materials helps conserve natural resources.

For more detailed information about recycling this product,

please contact your local city office, your local waste disposal

service or the point of sale where you purchased it.



and in other European schemes with separate collection systems)

By ensuring that batteries are disposed of properly, you will help prevent potential

negative consequences for the environment and health that might otherwise be

caused by improper disposal. Recycling materials helps conserve natural resources.

In the case of products which, for safety, performance or data protection reasons,

require a fixed connection to an internal battery/battery, it must only be replaced by

a qualified service person.

Hand over the product at the end of its life to suitable collection points for the

disposal of electrical and electronic equipment: this ensures that the battery inside

the product is also treated correctly.

For more detailed information on how to dispose of the used battery or product,

please contact your local municipal office, your local waste disposal service or the

point of sale where you purchased it.

According to Legislative Decree 49/2014 the product is included in the EEE (electri-

cal and electronic equipment) WEEE management (separate collection).

This symbol on the product or on the packaging

indicates that the battery should not be considered

normal household waste. On some battery types this

symbol may be used in combination with a chemical

symbol.

Chemical symbols for Mercury (Hg) or Lead (Pb) are

added if the battery contains more than 0. 0005%

mercury or 0. 004% lead.

Manuale d’uso

Monopattino Elettrico

Italiano

1. Monopattino

2. Manuale

3. Accessori:

- Chiave a brugola

- n° 4 viti

- Camera d’aria di scorta

- Stickers di ricambio

- Adattatore per gonfiaggio gomme

4. Caricabatteria



monopattino elettrico

Manuale d’uso

2. Schema delle Funzioni

Pannello di controllo

Freno

Luce frontale 



di ripiegamento

Motore

Porta di ricarica

Cavalletto



Luce del freno



Scomparto batteria

Problema al Motore

Indicatore di velocità





Modalità



Indicatore livello batteria

Luce

 Premere il pulsante ON/OFF per 3 secondi.

  Premere il pulsante ON/OFF per 3 secondi.

      Dopo aver acceso il Monopattino, premere il

pulsante ON/OFF per 1 secondo, la luce frontale si accenderà. Premere il pulsante

ON/OFF nuovamente per spegnere la luce.

 4.  All’attivazione del freno la luce posteriore lampeggerà.

 5. L’impostazione predefinita all’accensi-

one del Monopattino è Bassa velocità. Cambiare le impostazioni premendo velocemente

2 volte il pulsante ON/OFF entro 1 secondo.

 In questa modalità, la velocità è autolimitata a

7Km/h.

  Il controllo di velocità di crociera si attiva automaticamente se si mantie-

ne la stessa velocità per 10 secondi, a questo punto è quindi possibile rilasciare l’accelera-

tore; premere il freno o l’acceleratore e lo scooter ritorna alla modalità manuale.



Livello 1: <= 6 km / h

Livello 2: <= 20 km / h

Livello 3: > 20 km / h

 10.  Dopo 10 minuti di inutilizzo il Monopattino verrà spento

automaticamente.

 6.ndicatore del livello di batteria

33v-36v Un segmento acceso

36v-37v Due segmento acceso

37v-38.5v Tre segmento acceso

38.5v o superiore Tutti i segmenti accesi

 il primo segmento della batteria lampeggia una volta che

la tensione è inferiore a 33V, contemporaneamente partirà anche un avviso acustico

per 6 volte.

Segnalazione di problemi

Premendo la leva Acceleratore, fino alla massima escursione, per 10” (secondi) il monopat-

tino manterrà la medesima velocità anche rilasciando la leva.

Verificare il livello di carica della batteria con il veicolo fermo.

Codice Errore

E.1

E.2

E.4

E.5

E.6

E.7

E.8

Indicazioni

Problema all’acceleratore

Voltaggio batteria superiore a 42V

La corrente in uscita eccede i 14A

Guasto al freno

Guasto al cavo motore

Motore bloccato

Guasto alla linea di fase del motore

E.3

Voltaggio batteria inferiore a 32V

La page charge ...

Ducati PRO-I PLUS Manuel utilisateur

Marque: Ducati

Modèle: PRO-I PLUS

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

italiano: Ducati PRO-I PLUS Manuale utente
English: Ducati PRO-I PLUS User manual
español: Ducati PRO-I PLUS Manual de usuario
Deutsch: Ducati PRO-I PLUS Benutzerhandbuch

Documents connexes

Ducati PRO-II Manuel utilisateur

Ducati PRO-I PLUS Manuel utilisateur

Ducati PRO-I PLUS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents