Brilliant BHA120US-WH1 Guide d'installation

Marque: Brilliant

Modèle: BHA120US-WH1

Taper: Guide d'installation

Installation Guide

SINGLE SWITCH

Home Control

This short installation guide will

help you upgrade your home

with Brilliant.

It is important that you ﬁrst

review all of the instructions

to ensure you are comfortable

with the required steps.

If you are unsure about or

uncomfortable with the

installation, go to

brilliant.tech/install for more

instructions, and/or help with

ﬁnding a qualiﬁed electrician.

Thank you!

The Brilliant Team

Welcome!

Is your circuit 120V?

A 120V circuit is required, and is standard in North

American homes.

Is your wiring up to code, with Neutral and

Ground wires?

Both Neutral and Ground wires are required, and

present in most modern homes. Refer to Steps 5

and 6 for more details about wires.

Are you replacing a single or 3-way/multi-way

switch?

If you are replacing a 3-way/multi-way switch,

meaning that you can control the same light(s)

from more than one switch, you should conﬁrm

that the Brilliant can support your conﬁguration.

Refer to Step 1 for pictures of the supported

conﬁgurations.

Do you have the right tools?

A size 2 screwdriver is needed to remove your old

switch, and to install Brilliant.

Is your gang box a standard size?

A gang box is the electrical box in the wall, behind

the light switch. The box must have an interior

width of no less than 45mm, and an interior height

of no less than 70mm. Standard sizes will work.

Please conﬁrm the following:

Base

5 Wire Nuts 5 Extra Wires

FaceplateBase

It’s important to only use

supplied screws.

In the Box

To A Better Home

10 STEPS

Warning / Attention

Installing this product involves handling high voltage wiring.

Each step of the enclosed instructions must be followed carefully.

To avoid ﬁre, personal injury, or death, turn o your circuit

breakers and follow the proper safety precautions

before proceeding.

UNSURE ABOUT HANDLING ELECTRICAL WIRING?

CONSULT A QUALIFIED ELECTRICIAN.

L’installation de ce produit requiert la manipulation de câbles

électriques à haute tension. Veuillez suivre soigneusement les

instructions ci-jointe étape par étape. Aﬁn d’éviter tout risque

d’incendie, de blessure, ou de mort, coupez votre disjoncteur

ou coupe-circuit et suivez les consignes de sécurité avant de

continuer.

VOUS AVEZ DES DOUTES AU SUJET DE VOTRE CÂBLAGE

ÉLECTRIQUE?

TRAVAILLEZ AVEC UN ÉLECTRICIEN QUALIFIÉ.

(optional)

Base

Make sure Brilliant is compatible with

the location where you’re installing it.

If the 120V switch you are going to replace

activates a light that other switches also

control (often referred to as 3-way or

multi-way lighting), please ﬁnd the picture

of your setup on the next pages to conﬁrm

compatibility.

1 Check Compatibility

If your light is controlled by...

2 Switches

Will work: Two Brilliants

Won’t work: Brilliant and dimming switch

(at either end)

Non-Dimming

Dimming

See Step 6b, or visit

http://support.brilliant.tech

for more info on wiring multi-way circuits.

Will work: Brilliant and non-dimming switch

(at either end)

If your light is controlled by...

3 or More Switches

Will work: All Brilliants (connected through WiFi)

Will work: Brilliant at either end (or both ends) and a

non-dimming switch

Won’t work: Brilliant in the middle

Won’t work: Brilliant at the end, with a dimmer

anywhere else

Non-Dimming

Dimming

Base

2 Turn O Power

Turn the circuit breaker to OFF.

Before Proceeding

Kitchen

TV Room

Dining

Bedroom

Stairwell

Guest

Patio

Garage

ON OFF ON OFF

Conﬁrm you’ve turned o the right breaker by ﬂipping your light

switch on and o. If you have turned o the correct breaker, your

light won’t turn on.

Conﬁrmez que le bon coupe-circuit est éteint en utilisant

l’interrupteur à remplacer. Si le bon coupe-circuit est eectivement

éteint, vos lumières ne devraient pas s’allumer.

Avant de continuer

Base

3 Remove Light Switch

Unscrew your old switch cover and

light switch from the wall.

Pull the light switch out from the gang

box, and take pictures of the wires, in case

you need to reference them later. Then,

disconnect the attached wires, and remove

your old light switch.

4 Identify Your Circuit

Single Pole (Go to 5a)

One light switch that controls a light or

set of lights.

3-Way/Multi-Way (Go to 6a)

Two or more light switches that control the

same set of lights.

Line and load wires (black or red)

are connected to your old switch

Ground wire(s) (exposed green or copper)

typically come from the wall box

Neutral wire(s) (white)

typically come in a bundle and are fastened together

by a wire nut. You must connect all of them.

Single Pole

5a Identify Your Wires

Symbol

Ground

Line/Load*

Neutral

Green/Copper

Black or Red

White

Wall Wires

Green or Copper White

Black or Red

Single Pole

5b Connect Wires

*Line and Load are interchangeable.

Brilliant will automatically sense which is which.

Wires and Wire Nuts

Wires and Wire Nuts are used to connect

two or more wires together, or extend the

length. They are not usually needed, but

you will often use them for Neutral wires.

Select a wire extension from the box.

Match the color of the wires you’re

connecting.

Holding the wires together and parallel,

twist them together. Insert them into a

wire nut, and twist the wire nut clockwise

until secure. Double check by tugging on

the wires.

Tuck the bundle into the back of the

gang box.

Base

Step 1

Step 2

Step 3

Place wires in hole as deep as possible.

Turn screw clockwise with screwdriver.

Tighten until wires are secure. Test by tugging.

Single Pole

5c Screws and Wires

Then go to Step 7

Traveler wires

(black and red)

are connected to

your old switch

3-Way/Multiway

6a Identify Your Wires

Base

Symbol

Wall Wires

(Remove 3-Way Sticker)

3-Way/Multiway

6b Connect Wires

Red Traveler

Common (black)

is connected to your old switch

Ground wire(s) (exposed green or copper)

typically come from the wall box

Neutral wire(s) (white)

typically come in a pair and are fastened together

by a wire nut. You must connect all of them.

Green or Copper White

Black Traveler

Black Common

Ground

Common

Traveler 1*

Neutral

Traveler 2*

Green/Copper

Black Common

Black Traveler

White

Red Traveler

*Traveler wires are interchangeable.

Brilliant will automatically sense which is which.

Wires and Wire Nuts

Wires and Wire Nuts are used to connect

two or more wires together, or extend the

length. They are not usually needed, but

you will often use them for Neutral wires.

Select a wire extension from the box.

Match the color of the wires you’re

connecting.

Holding the wires together and parallel,

twist them together. insert them into a

wire nut, and twist the wire nut clockwise

until secure. Double check by tugging on

wires.

Tuck the bundle into the back of the

gang box.

Base

Step 1

Step 2

Step 3

Place wires in hole as deep as possible.

Turn screw clockwise with screwdriver.

Tighten until wires are secure. Test by tugging.

3-Way/Multiway

6c Screws and Wires

7 Install Base

Before Proceeding

Place wires in the gang box

and attach the Base.

Strain Reliefs

8 Test Light

Turn the circuit breaker back on to provide

power to the Base. Press the white button

in the center to turn the light on and o. If

the light does not turn on/o, do not install

the Faceplate. Instead, turn the breaker o,

remove the screws, and re-check your wire

connections.

Press

The strain reliefs are designed to bend to accommodate dierences in

gang box styles and mountings. Some bending of the strain reliefs is

normal, but be careful not to overtighten. Once the strain reliefs start

to bend, you can stop.

Les décharges de traction sont étudiées aﬁn de permettre à notre

produit de s’adapter à diérents types de corets de branchement.

Un certain ﬂéchissement des décharges est normal, mais prenez

garde de ne pas serrer trop fort. Des que les décharges commencent à

ﬂéchir, vous pouvez arrêter de serrer.

Avant de continuer

9 Secure Faceplate

Test the Base and secure the Faceplate.

Line up the brackets on the Base with the

holes on the Faceplate. Press the Faceplate

into the brackets and slide down until it

clicks. The Faceplate will start up.

Side Front

10 Conﬁgure Brilliant

Tap the “Begin Conﬁguration”

button to start the process, and

follow the prompts.

Next, it will ask you to connect

to Wi-Fi, and it is important to

do this so you can access your

other smart home devices.

Once the conﬁguration is

complete, you can “Add Devices”

to connect Brilliant to your

supported smart home devices.

Begin Conﬁguration

Connect Wi-Fi

Conﬁguration complete

Make your whole

home Brilliant

Once you’ve set Brilliant up, it’s easy to add

more. They’ll automatically set themselves

up and give you all the beneﬁts of Brilliant

throughout your home, including room-to-room

video intercom and more.

For help, educational videos, and additional

product information

visit us: http://support.brilliant.tech

Have a more pressing question?

email: [email protected]ech

2 switches 3 switches 4 switches

Congratulations, you’re

done with installation.

Use the Brilliant App to complete setup.

You can download the Brilliant App on

your iOS or Android device.

Before proceeding, remove the Faceplate

from the Base. Put one hand above it, and

grab both sides with the other hand. Then,

slide it up and o.

Next, with two hands and your ﬁngers on

the lower edge of the frame, gently pull

slightly down on the rear edge of the frame

until the clips come loose, and the bottom

edge of the frame releases from the display.

Removing and

replacing the display

frame with a new color

Side ViewSide View

Pull forward. Once the lower edge comes

loose, continue to rotate the bottom

edge up until you can easily unclip the

upper hooks from the top edge of the

Faceplate.

To attach a new frame, clip the top clips

onto the top edge of the Faceplate and

then rotate it down until the frame is

seated. To ensure the frame is properly

clipped on, ﬁrst squeeze the lower two

corners and then squeeze the upper

two corners. You can now reattach the

Faceplate to the wall.

6+ replaceable color frame options, such

as ivory, black, and silver, are available at

http://www.brilliant.tech

Step 1

Step 2

Step 3

510-00001 REV8

www.brilliant.tech

Contains FCC ID:VPYLB1DX

NOTE: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired

operation. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which

can be determined by turning the equipment o and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit dierent from that to

which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

FCC CAUTION

Changes or modiﬁcations not expressly approved by the party

responsible for compliance could void the user’s authority to operate

the equipment. This transmitter must not be co-located or operated in

conjunction with any other antenna or transmitter.

Brilliant BHA120US-WH1 Guide d'installation

Marque: Brilliant

Modèle: BHA120US-WH1

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Brilliant BHA120US-WH1 Installation guide

Brilliant BHA120US-WH1 Guide d'installation

Brilliant BHA120US-WH1 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents