Ohaus HB1DG Manuel utilisateur

Instruction Manual

Dry Block Heater, 1 Block, HB1AL

Dry Block Heater, 1 Block, HB1DG

Dry Block Heater, 2 Block, HB2AL

Dry Block Heater, 2 Block, HB2DG

Dry Block Heater, 4 Block, HB4AL

Dry Block Heater, 4 Block, HB4DG

Dry Block Heater, 6 Block, HB6AL

Dry Block Heater, 6 Block, HB6DG

Dry Block Heater, Heat Lid, HB2DGHL

Revision 7

2/14/2020

EN - English ......... 1

FR - Français ......... 16

ES - Español ......... 32

IT - Italiano ......... 48

DE - Deutsch ......... 64

PT - Português ......... 80

NL - Nederlands ......... 96

NO - Norsk ......... 101

DA - Dansk ......... 106

SV - Svenska ......... 111

FI - Suomi ......... 116

HU - Magyar ......... 121

PL - Polski ......... 126

CZ - Czech ......... 131

KR - Korean ......... 135

Package contents

Dry Block Heater

Power Cord

Instruction manual

Warranty Card

table of contents

Package Contents . . . . . . . . . . . . . . 1

Service Information . . . . . . . . . . . . . . 1

Installation . . . . . . . . . . . . . . 2

Maintenance & Servicing . . . . . . . . . . . . . . 2

Environmental Conditions . . . . . . . . . . . . . . 2

Equipment Disposal . . . . . . . . . . . . . . 2

Safety Instructions . . . . . . . . . . . . . . 3

Standards & Regulations . . . . . . . . . . . . . . 3

Analog Specifications . . . . . . . . . . . . . . 4-5

Analog Operating Instructions . . . . . . . . . . . . . . 6

Digital Control Panel . . . . . . . . . . . . . . 7

Digital Specifications . . . . . . . . . . . . . . 8-9

Digital Operating Instructions . . . . . . . . . . . . . . 10-14

Troubleshooting . . . . . . . . . . . . . . 15

1

service information

If the troubleshooting section does not resolve or describe your problem, contact your

authorized OHAUS service agent. For service assistance or technical support in the

United States call toll-free 1-800-672-7722 ext. 7852 between 8:00 AM and 5:00 PM EST.

An OHAUS product service specialist will be available to provide assistance. Outside the

USA, please visit our web site, www.ohaus.com to locate the Ohaus office nearest you.

Serial Number: _______________________________________________________

Date of Purchase: ____________________________________________________

Supplier: ___________________________________________________________

EN

Upon receiving the Ohaus Dry Block Heater, check to ensure that no damage has

occurred in shipment. It is important that any damage that occurred in transport is

detected at the time of unpacking. If you do find such damage the carrier must be

notified immediately.

After unpacking, place the Dry Block Heater on a level bench or table, away from

explosive vapors. Ensure that the surface on which the unit is placed will withstand

typical heat produced by the unit and place the unit a minimum of 6” (15.2cm) from

vertical surfaces. Always place the unit on a sturdy work surface.

The Dry Block Heater is supplied with a power cord that is inserted into the IEC

connector on the back of the unit first, then it can be plugged into a properly grounded

outlet. The 120V unit plugs into a 120 volt, 50/60 Hz source. The 230V unit plugs into

a 230 volt, 50/60 Hz source.

It is necessary to fill the Dry Block Heater well(s) with modular heating blocks because

empty block locations will affect performance. Place filled tubes in modular block(s),

then place the modular block(s) into the Dry Block Heater well(s).

maintenance & servicing

The Dry Block Heater is built for long, trouble-free, dependable service. No lubrication

or other technical user maintenance is required. It needs no user maintenance beyond

keeping the surfaces clean.

The unit should be given the care normally required for any electrical appliance. Avoid

wetting or unnecessary exposure to fumes. Spills should be removed promptly after

the unit has cooled down. DO NOT use a cleaning agent or solvent on the front panel

which is abrasive or harmful to plastics, nor one which is flammable. Always ensure

the power is disconnected from the unit prior to any cleaning. If the unit ever requires

service, contact your Ohaus representative.

The Dry Block Heaters are intended for general laboratory use. Safety cannot be

guaranteed if used outside of the intended use.

environmental conditions

Operating Conditions: Indoor use only.

Temperature: 18 to 33°C (64 to 91°F)

Humidity: 20% to 80% relative humidity, non-condensing

Altitude: 0 to 6,562 ft (2000 M) above sea level

Non-Operating Storage:

Temperature: -20 to 65°C (-4 to 149°F)

Humidity: 20% to 80% relative humidity, non-condensing

Installation Category II and Pollution Degree 2 in accordance with IEC 664.

equiPment disPosal

This equipment must not be disposed of with unsorted waste. It is your

responsibility to correctly dispose of the equipment at life-cycle-end

by handing it over to an authorized facility for separate collection and

recycling. It is also your responsibility to decontaminate the equipment in

case of biological, chemical and/or radiological contamination, so as

to protect the persons involved in the disposal and recycling of the

equipment from health hazards.

For more information about where you can drop off your waste of equipment, please

contact your local dealer from whom you originally purchased this equipment. By doing

so, you will help to conserve natural and environmental resources and you will ensure

that your equipment is recycled in a manner that protects human health.

2

installation intended use

EN

Please read the entire instruction manual before operating the Dry Block Heater.

WARNING! DO NOT use the Dry Block Heater in a hazardous atmosphere

or with hazardous materials for which the unit was not designed. Also, the

user should be aware that the protection provided by the equipment may

be impaired if used with accessories not provided or recommended by the

manufacturer, or used in a manner not specified by the manufacturer.

Always operate unit on a level surface for best performance and

maximum safety.

CAUTION! To avoid electrical shock, completely cut off power to the unit

by disconnecting the power cord from the unit or unplug from the wall outlet.

Disconnect unit from the power supply prior to maintenance and servicing.

Spills should be removed promptly, after the unit has cooled down. DO NOT

immerse the unit for cleaning. DO NOT operate the unit if it shows signs of

electrical or mechanical damage.

The main supply power cord provided with this product is rated to safely

handle the products electrical load under the stated environmental conditions.

DO NOT replace the cord with an inadequately rated main supply cord.

The Dry Block Heaters are designed to be operated in dry conditions. DO

NOT put water, oil or other fluids in the wells of the units. The chamber

that the modular heating blocks and baths sit in is not designed to be filled

with liquid or other fluids. DO NOT place anything other then the appropriate

heating block(s) in this cavity.

CAUTION! Dry Block Heaters are not explosion proof. Use caution when unit

is on or when heating volatile materials.

Earth Ground - Protective Conductor Terminal

Alternating Current

3

safety instructions standards & regulations

Compliance to the following standards and regulations is indicated by the corresponding mark

on the product.

Mark Standards and Regulations

OHAUS Corporation declares that the HB series dry block heaters comply with direc-

tives 2011/65/EU, 2014/30/EU, 2014/35/EU and standards EN 50581, EN 61010-1,

EN 61010-2-010, EN 61326-1.

The full text of the EU declaration of conformity is available at the following internet

address: www.ohaus.com/ce.

This product complies with directive 2012/19/EU. Please dispose of this product in

accordance with local regulations at the collecting point specified for electrical and

electronic equipment.

For disposal instructions in Europe, refer to www.ohaus.com/weee.

EN 61326-1

CAN/CSA C22.2 61010-1, CAN/CSA C22.2 61010-2-010

UL 61010-1, UL 61010-2-010

Global Notice

Warning: This is a Class A product. In a domestic environment this product may cause radio interfer-

ence in which case the user may be required to take adequate measures.

Canada Notice

This Class A digital apparatus complies with Canadian ICES-003.

FCC Notice

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial envi-

ronment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

Changes or modifications not expressly approved by Ohaus Corporation could void the user’s authority

to operate the equipment.

EN

4

analog dry block Heater sPecifications - 120 volt

1 Block 2 Block 4 Block 6 Block

Dimensions (L x W x H):

12.4 x 8 x 3.5”

(31.5 x 20.3 x 8.9cm)

15.4 x 8 x 3.5”

(39.1 x 20.3 x 8.9cm)

16.9 x 8 x 3.5”

(42.9 x 20.3 x 8.9cm)

20.9 x 8 x 3.5”

(53.1 x 20.3 x 8.9cm)

Electrical 120V 50/60 Hz: 0.92 amps, 110 watts 1.75 amps, 210 watts 2.6 amps, 310 watts 3.42 amps, 410 watts

Fuses: 5mm x 20mm, 5 amp quick acting, 250V

Temperature low range: ambient +5°C to 100°C

Temperature high range: 75°C to 150°C

Stability @ 37°C: +/-1°C +/-1.5°C +/-2°C +/-2°C

Uniformity w/in the block

@ 37°C:

+/-0.1°C

Uniformity across

similar blocks @ 37°C:

N/A +/-0.1°C +/-0.2°C +/-0.3°C

Stability @ 60°C: +/-3°C +/-4°C +/-5°C +/-5°C

Uniformity w/in the block

@ 60°C:

+/-0.6°C

Uniformity across

similar blocks @ 60°C:

N/A +/-0.8°C +/-1.2°C +/-1.4°C

Heat-up time to 100 °C*:

16 min. 16 min. 23 min. 30 min.

Controls:

rocker switch

heat indicator light

low temperature knob, variable 1 to 10 dial markings

high temperature knob, variable 1 to 10 dial markings

Ship weight:

5.8lbs (2.6kg) 6.4lbs (2.9kg) 8.5lbs (3.9kg) 10lbs (4.5kg)

EN

* Conditions Permitting

analog dry block Heater sPecifications - 230 volt

5

1 Block 2 Block 4 Block 6 Block

Dimensions (L x W x H):

12.4 x 8 x 3.5”

(31.5 x 20.3 x 8.9cm)

15.4 x 8 x 3.5”

(39.1 x 20.3 x 8.9cm)

16.9 x 8 x 3.5”

(42.9 x 20.3 x 8.9cm)

20.9 x 8 x 3.5”

(53.1 x 20.3 x 8.9cm)

Electrical 230V 50/60 Hz: 0.5 amps, 110 watts 0.92 amps, 210 watts 1.35 amps, 310 watts 1.79 amps, 410 watts

Fuses: 5mm x 20mm, 5 amp quick acting, 250V

Temperature low range: ambient +5°C to 100°C

Temperature high range: 75°C to 150°C

Stability @ 37°C: +/-1.5°C +/-2°C +/-2.5°C +/-2.5°C

Uniformity w/in the block

@ 37°C:

+/-0.4°C

Uniformity across

similar blocks @ 37°C:

N/A +/-0.1°C +/-0.2°C +/-0.3°C

Stability @ 60°C: +/-3°C +/-4°C +/-5°C +/-5°C

Uniformity w/in the block

@ 60°C:

+/-0.6°C

Uniformity across

similar blocks @ 60°C:

N/A +/-0.8°C +/-1.2°C +/-1.4°C

Heat-up time to 100 °C*:

16 min. 16 min. 23 min. 30 min.

Controls:

rocker switch

heat indicator light

low temperature knob, variable 1 to 10 dial markings

high temperature knob, variable 1 to 10 dial markings

Ship weight:

5.8lbs (2.6kg) 6.4lbs (2.9kg) 8.5lbs (3.9kg) 10lbs (4.5kg)

EN

* Conditions Permitting

6

These multi-purpose units are ideal for incubation and activation of cultures, enzyme

reactions, immunoassays, melting/boiling points and a wide variety of other laboratory

procedures.

1. Switch the three (3) position rocker power switch from the center off position to

the low range or high range position as desired. The controls are divided into two

separate heating ranges, both thermostats having graduations to assist in setting

the desired temperatures. The left hand ‘low temperature adjust’ controls from

slightly above ambient to approximately 100°C. The right hand ‘high temperature

adjust’ controls from approximately 75°C to 150°C.

2. The rocker switch has a center off position and is used to select the desired operating

range. When operating at the point where the two thermostats overlap in temperature

range, the proper thermostat must be chosen for the task being performed. Move

the power switch to the desired operating range and turn the matching range

temperature control knob clockwise to increase the temperature within the range

selected. The heat indicator light will illuminate during the operation of the heater.

3. The temperature may be verified by placing a calibrated thermometer in the test

solution or by insertion in the modular block thermometer well provided. This hole

fits regular glass bulb thermometers or small diameter digital probes. Due to air

currents and radiation losses, the temperature in the test solution will be lower than

the temperature in the block itself. For the most accurate readings a thermometer

should be placed in a sample test tube with solution matching the samples being

tested. If the temperature is too high or too low, adjust clockwise to increase

temperature, counter-clockwise to decrease temperature. Slight adjustments will

usually suffice to correct the temperature setting. When the heat indicator light

flashes on and off intermittently, check the temperature again. Allow sufficient

time for the temperature to stabilize before re-adjusting. This procedure should be

followed until the desired temperature is reached.

low temperature

adjust knob

high temperature

adjust knob

heat indicator light

rocker switch

Ohaus Analog 1 Block Heater with modular block and tubes

analog dry block Heater oPerating instructions

EN

The front panel of the Dry Block Heater contains all the controls and displays needed

to operate the unit.

A. Standby button/standby indicator light: The standby indicator light will

illuminate when the unit is plugged in. The unit will be in standby mode. Press the

standby button to start the temperature and time functions. The standby indicator

light will shut off. Press the standby button again and the unit will once again be in

standby mode.

B. Caution hot top indicator light: Illuminates when the plate temperature is above

40°C (104°F).

C. Plate indicator light: Illuminates when the optional external RTD probe is not

being used. The temperature displayed is the plate temperature.

D. Probe indicator light: Illuminates when the optional external RTD probe is

plugged in. The temperature displayed is the probe temperature, NOT the plate

temperature.

E. Actual indicator light: Illuminates when the temperature displayed is the actual

temperature of the plate/RTD probe.

F. Set-point indicator light: Illuminates when the set-point temperature is displayed.

G. Temperature display: Displays the actual/set-point temperatures in conjunction

with the actual/set-point indicator lights. H. Up/down arrows for set-point control.

On/off button starts/stops the heating function.

I. Time display: Displays accumulated time (continuous mode) or how much time

is remaining (timed mode). The display range is from 0 to 9,999 minutes in one (1)

second increments. The display will indicate minutes and seconds until the timer

reaches 99 minutes and 59 seconds (99:59), then the display will automatically

display minutes up to 9,999. J. Up/down arrows for set-point control. On/off button

starts/stops the timer function.

digital dry block Heater control Panel

E.

A.

J.

H.

F.

D.

C.

I.

G.

B.

7

EN

8

digital dry block Heater sPecifications - 120 volt

1 Block 2 Block 4 Block 6 Block 2 Block with Lid

Dimensions (L x W x H):

12.4 x 8 x 3.5”

(31.5 x 20.3 x 8.9cm)

15.4 x 8 x 3.5”

(39.1 x 20.3 x 8.9cm)

16.9 x 8 x 3.5”

(42.9 x 20.3 x 8.9cm)

20.9 x 8 x 3.5”

(53.1 x 20.3 x 8.9cm)

15.4 x 8 x 7”

(39.1 x 20.3 x 17.8cm)

Electrical 120V 50/60 Hz: 0.92 amps, 110 watts 1.75 amps, 210 watts 2.6 amps, 310 watts 3.42 amps, 410 watts 3.0 amps, 400 watts

Fuses: 5mm x 20mm, 5 amp quick acting, 250V

Temperature range: ambient +5°C to 120°C ambient +5°C to 100°C

Stability @ 37°C: +/-0.1°C

Uniformity w/in the block

@ 37°C:

+/-0.1°C +/-0.1°C

Uniformity across simi-

lar blocks @ 37°C:

N/A +/-0.1°C +/-0.2°C +/-0.3°C +/-0.1°C

Stability @ 60°C: +/-0.4°C

Uniformity w/in the block

@ 60°C:

+/-0.4°C

Uniformity across simi-

lar blocks @ 60°C:

N/A +/-0.5°C +/-0.8°C +/-1°C +/-0.5°C

Heat-up time to 100 °C*:

16 min. 16 min. 23 min. 30 min. 30 min.

Controls:

see page 7

Ship weight:

5.8lbs (2.6kg) 6.4lbs (2.9kg) 8.5lbs (3.9kg) 10lbs (4.5kg) 7lbs (3.2kg)

EN

* Conditions Permitting

digital dry block Heater sPecifications - 230 volt

9

1 Block 2 Block 4 Block 6 Block 2 Block with Lid

Dimensions (L x W x H):

12.4 x 8 x 3.5”

(31.5 x 20.3 x 8.9cm)

15.4 x 8 x 3.5”

(39.1 x 20.3 x 8.9cm)

16.9 x 8 x 3.5”

(42.9 x 20.3 x 8.9cm)

20.9 x 8 x 3.5”

(53.1 x 20.3 x 8.9cm)

15.4 x 8 x 7”

(39.1 x 20.3 x 17.8cm)

Electrical 230V 50/60 Hz: 0.5 amps, 110 watts 0.92 amps, 210 watts 1.35 amps, 310 watts 1.79 amps, 410 watts 1.65 amps, 400 watts

Fuses: 5mm x 20mm, 5 amp quick acting, 250V

Temperature range: ambient +5°C to 120°C ambient +5°C to 100°C

Stability @ 37°C: +/-0.2°C

Uniformity w/in the block

@ 37°C:

+/-0.2°C +/-0.1°C

Uniformity across simi-

lar blocks @ 37°C:

N/A +/-0.1°C +/-0.2°C +/-0.3°C +/-0.1°C

Stability @ 60°C: +/-0.4°C

Uniformity w/in the block

@ 60°C:

+/-0.4°C

Uniformity across simi-

lar blocks @ 60°C:

N/A +/-0.5°C +/-0.8°C +/-1°C +/-0.5°C

Heat-up time to 100 °C*:

16 min. 16 min. 23 min. 30 min. 30 min.

Controls:

see page 7

Ship weight:

5.8lbs (2.6kg) 6.4lbs (2.9kg) 8.5lbs (3.9kg) 10lbs (4.5kg) 7lbs (3.2kg)

EN

* Conditions Permitting

10

Designed for applications that require repeatable results and superior temperature

stability. These multi-purpose units are ideal for incubation and activation of cultures,

enzyme reactions, immunoassays, melting/boiling points, and a wide variety of other

laboratory procedures.

For best performance, the Dry Block Heater should be used in a stable environment.

The unit’s environment should have no air currents, drafts or temperature changes

and it cannot be placed in direct sunlight. The unit requires a stable electrical supply

that is free of voltage fluctuations. An unstable environment will adversely affect the

performance of the unit. For example, even minor air drafts or temperature changes

will adversely affect the unit’s ability to maintain a stable temperature.

1. Getting ready:

a. When using the external RTD probe, plug the RTD probe into the three (3) pin

DIN connector at the back of the unit and place the thermometer portion in the

thermometer well of the modular block. When using multiple blocks, place the

RTD probe in the front right modular block.

b. Press the standby button to change the unit from standby mode. The

temperature display, time display and probe indicator light will illuminate. When

not using the RTD probe, the plate indicator light will illuminate. The temperature

display will alternate between the actual and set-point temperatures.

2. Setting temperature:

a. Press the up/down arrows to the right of the temperature display until you reach

the desired temperature. Holding down either the up or down arrow will cause

the set temperature to change rapidly, a single pressing of either key will move

the set temperature by 0.1°C. When you release the button, the display will

blink off and then on, indicating the new set temperature has been accepted.

Once the set-point has been programmed and the keys are not being pressed,

press the on/off button to the right of the temperature display to activate the

heating function. A green indicator light will illuminate next to the on/off button

indicating the heating function is on. The actual and set-point indicator lights

will alternate between set and actual temperatures. There are three (3) audible

beeps to indicate the set-point temperature has been reached.

b. Set-point temperature adjustments can be made without interrupting heating

using the up/down arrows to the right of the temperature display. After the

change has been made and you release the button, the display will blink off and

then on indicating the new set temperature has been accepted.

c. To stop heating, press the on/off button to the right of the temperature display.

d. Allow time for the temperature to stabilize. The actual temperature displayed is

the temperature at the bottom of the modular block or of the RTD probe. Once

the displayed actual temperature agrees with the set temperature, several

minutes should be allowed for the temperature to stabilize throughout the block

evenly.

Overshoot protection: If the unit exceeds the set temperature by 10°C, the unit will

automatically stop heating.

3. Setting timed mode: Programmed time.

a. Press the up/down arrows to the right of the time display until you reach the

desired time.

b. Start this function by pressing the on/off button to the right of the time display,

the unit will run for the selected time. When using the timer in conjunction

with the heating function, when the time display reaches zero (0:00), four (4)

audible beeps will indicate the time down function is complete. Both the time

and heating functions will shut off automatically and the time display will default

back to the set time. To repeat for the same time, simply depress the on/off

button again.

c. To interrupt an automatic timing cycle before it is completed, press the on/

off button to the right of the time display. The time display will flash until you

resume the time function by pressing the on/off button again. This interrupt will

not stop the heating function, the heating function will stop only when the timer

reaches zero (0:00).

digital dry block Heater oPerating instructions

EN

4. Setting time to zero (0:00) and continuous mode: Accumulated time.

a. Press and hold the on/off button to the right of the time display. After three (3)

seconds, the display will indicate the previous set time.

b. Simultaneously press both the up and the down arrows, the display will indicate

zero (0:00). The unit time is now set to zero (0:00) minutes. Alternately, you can

use the up/down arrows to get to zero (0:00).

c. Press the on/off button to the right of the time display, the display will indicate

actual running time. The up/down arrows will become inactive. To stop timer,

press the on/off button again. IMPORTANT: This will not affect the heating

function. Press the on/off button to the right of the heat display to interrupt the

heating function.

d. To reset, press and hold the on/off button to the right of the time display. After

three (3) seconds the display will indicate the previous set time, which was zero

(0:00).

5. Turning unit off:

a. To turn the unit off, press the standby button, the temperature and time displays

will be blank, the standby indicator light will turn on.

CALIBRATION PROCEDURE

This procedure is used to fine tune and calibrate the block temperature at a specific

temperature setting. It will only be active without an external temperature probe

connected. This process may be repeated for up to three (3) separate set-points. If

a fourth calibration set-point is entered, the first set-point entered will be overwritten.

1. Turn unit on.

2. Set desired temperature.

3. Stabilize twenty (20) minutes or more, measuring the block temperature with a

calibrated precision instrument or thermometer.

4. Press and hold standby button, then press the temperature up button once. The

unit will beep two (2) times, confirming calibration mode. The display will now be

flashing.

5. Press the temperature up/down arrows until the display matches the temperature

probe/thermometer.

6. Press standby button to exit calibration mode and return to normal heating.

This process may be repeated at the same set-point multiple times for fine tuning if

desired.

The unit will now use the biased offset for that specific temperature setting and

increase or decrease temperature accordingly to bring the block temperature to set

temperature. The decimal point of the display will flash to indicate a biased offset is

being used. All other temperature settings will use the standard internal calibration. This

offset will be stored in memory and retained until reset.

To restore unit to factory setting:

Press and hold standby button while pressing the temperature down button once. The

reset will be confirmed with two (2) beeps. Press the standby button to exit calibration

mode and return to normal heating.

BEEPER PREFERENCE

To silence beeper operation (except for error codes), with the unit in standby mode,

press and hold the time on/off button and press the standby button. To restore

normal beeper operation, remove AC power to unit for 10 seconds and then restore.

Alternately, you may have to turn the unit on and press and hold the standby button

and press and hold the time on/off button simultaneously.

11

EN

12

MODULAR HEATING BLOCKS AND SAMPLES

Only Ohaus Modular Heating Blocks are to be used in the Dry Block Heaters.

1. Select the proper blocks that will be a precise fit for the tubes, plates, or vials that

you will be using for your application.

2. Only plastic or glass tubes, plates, or vials are to be used in the Modular Heating

Blocks. Metal vessels will adversely affect the temperature performance of the unit.

Metal vessels will dissipate too much heat into the air, thus adversely affecting the

temperature readings of the unit.

3. Blocks need to be in all positions on the unit so the heating plate is not exposed to

the environment.

4. To ensure proper heating, the tubes, plates, or vials that are used must be the

correct size for the Modular Heating Block. The tubes, plates or vials must fit

securely in the hole with no air gaps and maintain as much contact as possible with the

wall of the block. This will ensure good thermal contact between the Modular Heating

Block and the tube, plate or vial you are using for your application.

5. For proper heating, the fluid level within your tube, plate or vial should not exceed

the height of the Modular Heating Block. If your application requires the fluid level

to be above the height of the block, then a temperature cover is recommended.

6. When using a temperature measuring device in a sample, the end of the probe

should be placed at the bottom of the sample and the height of the liquid should

not exceed the height of the Modular Heating Block. Ensure that your temperature

measuring device is designed for immersion in liquids.

7. Contact your Ohaus representative for information on ordering Modular Heating

Blocks and other Dry Block Heater accessories.

OPTIONAL EXTERNAL RTD PROBE KIT (FOR DIGITAL UNITS)

1. If your application requires a high level of accuracy, the optional external RTD

probe should be used with the Dry Block Heater.

2. Follow the ‘Operating Instructions’ for the proper installation of the optional

external RTD probe. With the RTD probe plugged into the back of the unit, place

the thermometer portion in the thermometer well of the Modular Heating Block.

With the external RTD probe in place, the RTD probe is now driving the displayed

temperature setting for the operation of the unit, not the heating plate of the unit.

Once the optional external RTD probe is properly installed, the probe indicator LED

above the temperature display will be illuminated.

oPerating instructions cont’d

EN

TEMPERATURE TESTING

1. To ensure good thermal conductivity, select the proper Modular Heating Block

for your application. Select the proper tubes or vials which are the proper size for

the Modular Heating Block. Close contact, with no air gaps, must be maintained

between the walls of the Modular Heating Block well and the sides of the tubes or

vials.

2. Fill the tubes or vials so that the fluid level does not rise above the top surface of

the Modular Heating Block.

3. Select a temperature measuring device that is designed for immersion in liquids.

Place your calibrated temperature measuring device in one of the samples so it

reaches the bottom of the tube or vial. Once the temperature measuring device is

placed in the fluid sample, ensure the fluid level is still below the top surface of the

Modular Heating Block.

4. Set the desired temperature on the unit, allow the unit to reach this temperature,

and let the unit stabilize for an additional twenty (20) minutes or more before taking

any temperature readings.

5. The temperature can also be tested by utilizing the thermometer hole in the Modular

Heating Block. A calibrated temperature measuring device can be inserted into the

thermometer hole where there is a snug fit and close contact between the walls

of the block and the temperature device. The temperature device must reach the

bottom of this hole with no air gaps. Follow the procedure above for allowing the

unit to reach temperature and stabilize before taking any temperature readings.

6. If the measured temperature on your temperature measuring device does not

match the actual temperature on the display of the unit (for Digital units only), then

the single point calibration procedure can be used. By doing this, the unit will now

be more accurate at that set-point for your specific application.

STABILITY TESTING

1. The manufacturer has performed temperature stability tests on Dry Block Heaters.

The manufacturer used calibrated temperature measuring device for the stability

tests. Units were set-up with the proper number of Modular Heating Blocks so

the heater plates were not exposed to the environment. A calibrated temperature

measuring device was inserted into the thermometer well of one block on each

unit. The testing temperature was set, the units were allowed to heat up and

stabilize for a minimum of twenty (20) minutes and then temperature readings

were recorded at regular intervals for four (4) hours. These tests confirmed the

temperature stability of the units.

2. The recommended procedure for testing the unit’s stability is as follows:

a. Set-up the unit in a stable environment.

b. Set-up the unit with the proper number of Modular Heating Blocks for the unit.

Place a calibrated temperature measuring device into the thermometer well of

the Modular Heating Block. The temperature device should have a snug fit with

no air gaps in the thermometer well. Set the temperature of the unit. Allow the

unit to reach temperature and stabilize for twenty (20) minutes or more and then

take temperature readings for stability.

c. Another method to test for stability is to set up the unit with the proper number of

Modular Heating Blocks and then place the proper fitting tubes or vials into the

blocks. Fill the tubes or vials with liquid, where the liquid level is lower than

the top surface of the Modular Heating Block. Use a calibrated temperature

measuring device that is designed for immersion in liquids, and place the

temperature probe in the bottom of one of the tubes or vials in one block. Set

the temperature of the unit. Allow the unit to reach temperature and stabilize for

twenty (20) minutes or more and then take temperature readings for stability.

Please note the characteristics of the liquid used for the test and the fit of the

tube or vial in the Modular Heating Block can affect the results of a stability

test for the Dry Block Heaters. Tubes and vials must be the proper size for the

Modular Heating Block so there is a secure fit with no air gaps to ensure good

thermal contact.

13

EN

14

UNIFORMITY TESTING

1. The manufacturer has performed uniformity tests on Dry Block Heaters to

ensure even heating across the entire heater plate. For the one block heaters,

the manufacturer used a specially designed Modular Heating Block with five (5)

temperature holes. Five independent calibrated temperature measuring devices

were used during the test. For multiple block units, Modular Heating Blocks were

placed in all positions to cover the entire heating plate and then an independent

calibrated temperature measuring device was used in the thermometer well of

each block. For all tests, the tip of the temperature measuring device was an exact

fit for the temperature well in the Modular Heating Block with no air gaps. The

temperature was set and the units were allowed to heat up and stabilize for twenty

(20) minutes or more. Readings were then taken at regular intervals to monitor the

temperature uniformity for four (4) hours. These tests were repeated after rotating

the temperature measuring devices to different thermometer well positions to confirm

the temperature uniformity of the units.

2. The recommended procedure for testing the unit’s temperature uniformity is as

follows:

a. Set-up the unit in a stable environment.

b. Set-up the unit with the proper number of Modular Heating Blocks to cover the

entire heating plate. Then set up the blocks with the proper fitting tubes or vials.

Place liquid samples in tubes or vials where the liquid level is lower than the

height of the top surface of the Modular Heating Block.

c. Select multiple calibrated temperature measuring devices that are designed

for immersion in liquids. Use these temperature measuring devices at the

same time across various positions in the Modular Heating Block(s). Place the

temperature probes in the bottom of several of the filled tubes or vials. Ensure

the liquid levels in the tubes or vials with the temperature probes does not rise

above the height of the top surface of the Modular Heating Block.

d. Set the temperature of the unit. Allow the unit to reach temperature and stabilize

for twenty (20) minutes or more and then take temperature readings from all the

temperature devices to test for temperature uniformity

oPerating instructions cont’d

e. Please note the characteristics of the liquid used for the test and the fit of the

tube or vial in the Modular Heating Block can affect the results of the uniformity

test for the Dry Block Heaters. Tubes and vials must be the proper size for the

Modular Heating Block so there is a secure fit with no air gaps to ensure good

thermal contact.

EN

To clear error press the standby button

Problem Cause Solution

Unit fails to power on Missing or blown fuse

Add or replace fuse as necessary.

If problem persists, please contact your Ohaus representative for repair.

E1 Faulty temperature sensor

This error cannot be fixed by the end user.

Please contact your Ohaus representative for repair.

E2

Thermocouple failure or

Heating element failure

This error cannot be fixed by the end user.

Please contact your Ohaus representative for repair.

E3

Unit cannot reach set-point or

Probe not in thermometer well

If using probe, verify probe is in thermo well and follow Single Point Calibration

instructions on page 11. If problem persists, please contact your Ohaus representative

for repair.

Errors will cause heating function to cease. Timing functions will be unaffected.

15

troublesHooting

EN

Manuel d’Instruction

Chauffage à sec, 1 Bloc, HB1AL

Chauffage à sec, 1 Bloc, HB1DG

Chauffage à sec, 2 Blocs, HB2AL

Chauffage à sec, 2 Blocs, HB2DG

Chauffage à sec, 4 Blocs, HB4AL

Chauffage à sec, 4 Blocs, HB4DG

Chauffage à sec, 6 Blocs, HB6AL

Chauffage à sec, 6 Blocs, HB6DG

Chauffage à sec, Bouchon, HB2DGHL

EN - English ......... 1

FR - Français ......... 16

ES - Español ......... 32

IT - Italiano ......... 48

DE - Deutsch ......... 64

PT - Português ......... 80

NL - Nederlands ......... 96

NO - Norsk ......... 101

DA - Dansk ......... 106

SV - Svenska ......... 111

FI - Suomi ......... 116

HU - Magyar ......... 121

PL - Polski ......... 126

CZ - Czech ......... 131

KR - Korean ......... 135

contenu de l’emballage

Bain à sec chauffant

Cordon d’alimentation

Manuel d’instruction

Carte de garantie

table des matiéres

Contenu de l’emballage . . . . . . . . . . . . . . 17

Des informations de service . . . . . . . . . . . . . . 17

Installation . . . . . . . . . . . . . . 18

Maintenance et réparation . . . . . . . . . . . . . . 18

Conditions ambiantes . . . . . . . . . . . . . . 18

Élimination du matériel . . . . . . . . . . . . . . 18

Consignes de sécurité . . . . . . . . . . . . . . 19

Normes et réglementations . . . . . . . . . . . . . . 19

Spécifications - Bain à sec chauffant analogique . . . . . . . . . . . . . 20-21

Consignes d’utilisation - Bain à sec chauffant analogique . . . . . . . . . 22

Panneau de commande numérique . . . . . . . . . . . . . . 23

Spécifications - Bain à sec chauffant numérique . . . . . . . . . . . . . 24-25

Consignes d’utilisation - Bain à sec chauffant numérique. . . . . . . . . 26-30

Dépannage . . . . . . . . . . . . . . 31

17

des informations de service

Si la section de dépannage ne permet pas de résoudre ou ne décrit pas le problème, con-

tacter l’agent d’entretien agréé OHAUS. Pour un service d’assistance ou une prise en charge

technique aux États-Unis, composer le numéro gratuit 1-800-672-7722, poste 7852 entre

8h00 et 17h00 (GMT - 5).

Un spécialiste du service produit OHAUS est disponible pour apporter son aide. En dehors

des États-Unis, bien vouloir se rendre sur notre site web, www.ohaus.com pour rechercher la

filiale OHAUS la plus proche.

Numéro de série: _________________________________________________________

Date d’achat: _____________________________________________________________

Fournisseur: ______________________________________________________________

FR

Dès réception du bain à sec chauffant Ohaus, vérifiez qu’il n’a pas été endommagé pen-

dant le transport. Il est important que tout dommage résultant du transport soit détecté lors

du déballage. Informez immédiatement le transporteur en cas de dommage.

Après le déballage, placez le bain à sec chauffant à sec sur un plan de travail ou une table

de niveau, à l’écart de toute vapeur explosive. Assurez-vous que la surface sur laquelle

l’appareil est placé résistera à la chaleur typiquement produite par l’appareil et placez ce

dernier à au moins 15 cm des surfaces verticales. Placez toujours l’appareil sur un plan

de travail solide.

Le bain à sec chauffant est fourni avec un cordon d’alimentation qu’il vous faut tout d’abord

insérer dans le connecteur IEC situé au dos de l’appareil avant de le brancher dans une

prise correctement mise à la terre. L’appareil de 120 V se branche dans une source

d’alimentation de 120 volts, 50/60 Hz. L’appareil de 230 V se branche dans une source

d’alimentation de 230 volts, 50/60 Hz.

Il est nécessaire de remplir le(s) puit(s) du bain à sec chauffant de blocs chauffants modu-

laires car des emplacements de bloc vides affectent les performances. Placez les tubes

pleins dans le(s) bloc(s) modulaire(s) puis posez ce(s) bloc(s) dans les puits du bain à sec

chauffant.

maintenance et réParation

Le bain à sec chauffant est construit pour fonctionner longtemps, de façon efficace et sans

problème. Aucun graissage ou tout autre entretien n’est requis de la part de l’utilisateur.

Le seul entretien nécessaire est de maintenir les surfaces propres. Votre système doit être

traité avec le même soin que n’importe quel autre appareil électrique. Évitez de le mouiller

ou de l’exposer inutilement à des émanations. Les renversements doivent être rapidement

nettoyés une fois que l’appareil s’est refroidi. Pour nettoyer le panneau avant, NE PAS uti-

liser de nettoyant ou de solvant abrasif ou pouvant endommager le plastique, ni de produit

inflammable. Toujours s’assurer que l’alimentation est débranchée avant d’effectuer tout

nettoyage. Si l’appareil doit être réparé, contactez votre représentant Ohaus.

Les plaques chauffantes céramiques sont prévues pour un usage général en

laboratoire. La sécurité ne saurait en cas d’utilisation non prévue.

conditions ambiantes

Conditions de fonctionnement : Pour une utilisation à l’intérieur uniquement.

Températures : 18 à 33 °C (64 to 91°F)

Humidité : 20 à 80 % HR, sans condensation

Altitude : 0 à 6,562 ft (2000 m) au-dessus du niveau de la mer

Stockage :

Températures : -20 à 65 °C (-4 to 149°F)

Humidité : 20 à 80 % HR, sans condensation

Installation de Catégorie II et palier de pollution 2 suivant la norme CEI 664.

élimination du matériel

Ce dispositif ne doit pas être éliminé parmi les déchets non triés. Il est

votre responsabilité d’éliminer de façon appropriée le dispositif à la fin de

son cycle de vie en le confiant à une installation autorisée spécialisée dans

la collecte de déchets tries et le recyclage. Il est aussi votre responsabilité

de décontaminer tout dispositif en cas de contamination biologique, chi-

mique ou radiologique, de façon à protéger les personnes impliquées dans

l’élimination et le recyclage des risques sanitaires.

Pour obtenir plus d’informations concernant les endroits où vos dispositifs peuvent être

déposés pour l’élimination, contactez le concessionnaire auprès duquel vous avez acheté

ce dispositif. En faisant cela, vous contribuerez à conserver des ressources naturelles et

environnementales et vous garantirez que votre dispositif est recyclé d’une manière qui

préserve la santé humaine.

18

installation utilisation Prévue

FR

Veuillez lire le mode d ‘emploi complet avant d’ utiliser le chauffe - eau.

Attention! N’utilisez pas le chauffe-bloc sec dans une atmosphère dangereuse ou

avec des matières dangereuses pour lesquelles l’appareil n’a pas été conçu. De plus,

l’utilisateur doit savoir que la protection fournie par l’équipement peut être altérée si

elle est utilisée avec des accessoires non fournis ou recommandés par le fabricant

ou utilisés d’une manière non spécifiée par le fabricant.

Toujours faire fonctionner l’appareil sur une surface plane pour Sécurité maximale.

Mise en garde! Pour éviter tout risque d’électrocution, coupez complètement

l’alimentation de l’appareil en débranchant le cordon d’alimentation de l’appareil ou

débranchez-le de la prise murale. Débrancher l ‘appareil de l’ alimentation avant de

procéder à l ‘entretien et à l’ entretien.

Les déversements doivent être retirés rapidement, après refroidissement de

l’appareil. Ne pas plonger l’appareil pour le nettoyer. Ne pas faire fonctionner l

‘appareil s’il présente des signes de dommages électriques ou mécaniques.

Le cordon d’alimentation principal fourni avec ce produit est noté pour maintenir

la charge électrique des produits sous des conditions environnementales définies.

EVITEZ de remplacer ce cordon d’alimentation avec un autre cordon d’alimentation

noté différemment.

Les réchauffeurs à blocs secs sont conçus pour être utilisés dans des conditions

sèches. Ne pas mettre d’eau, d’huile ou d’autres fluides dans les puits des unités. La

chambre dans laquelle les blocs de chauffage et les bains modulaires sont installés

n’est pas conçue pour être remplie de liquide ou d’autres fluides. Ne placez rien

d’autre que le (s) bloc (s) chauffant (s) approprié (s) dans cette cavité.

Mise en garde! Les chauffe-blocs secs ne sont pas à l’épreuve des explosions. Soyez

prudent lorsque l’appareil est sous tension ou lorsqu’il chauffe des matières volatiles.

Terre - Borne de protection de conducteur

Courant alternatif

19

consignes de sécurité normes et réglementations

La conformité aux normes et réglementations suivantes est indiquée par la marque correspon-

dante sur le produit.

Marque Normes et Réglementations

OHAUS Corporation déclare que les radiateurs secs série HB sont conformes aux

directives 2011/65 / UE, 2014/30 / EU, 2014/35 / EU et aux normes EN 50581, EN

61010-1, EN 61010-2-010, EN 61326- 1.

Le texte intégral de la déclaration de conformité de l’UE est disponible à l’adresse

Internet suivante: www.ohaus.com/ce.

Ce produit est conforme à la directive 2012/19 / UE. Veuillez jeter ce produit confor-

mément à la réglementation locale au point de collecte spécifié pour les équipements

électriques et électroniques.

Pour obtenir des instructions d’élimination en Europe, consultez www.ohaus.com/

weee.

EN 61326-1

CAN/CSA C22.2 61010-1, CAN/CSA C22.2 61010-2-010

UL 61010-1, UL 61010-2-010

Avis Global

Avertissement: Il s’agit d’un produit de classe A. Dans un environnement domestique, ce produit

peut causer des interférences radio, auquel cas l’utilisateur peut être amené à prendre des mesures

adéquates.

Canada Avis

Cet appareil numérique de classe A est conforme à la norme ICES-003 du Canada.

Avis de la FCC

REMARQUE: Cet équipement a été testé et déclaré conforme aux limites d’un appareil numérique de

classe A, conformément à la partie 15 des règles de la FCC. Ces limites sont conçues pour fournir

une protection raisonnable contre les interférences nuisibles lorsque l’équipement est utilisé dans un

environnement commercial. Cet équipement génère, utilise et peut émettre de l’énergie radiofréquence

et, s’il n’est pas installé et utilisé conformément au manuel d’instructions, peut causer des interférences

nuisibles aux communications radio. Le fonctionnement de cet équipement dans une zone résiden-

tielle est susceptible de causer des interférences nuisibles, auquel cas l’utilisateur devra corriger

l’interférence à ses propres frais.

Les modifications ou modifications non expressément approuvées par Ohaus Corporation peuvent

annuler l’autorisation de l’utilisateur d’utiliser l’équipement.

FR

La page charge ...

Ohaus HB1DG Manuel utilisateur

Ohaus HB1DG Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents