Allis-Chalmers 2691089-00 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur
1739461
Revision C
en
Operator’s Manual
es
Manual del operador
Hydro Tractors
Mfg. No. Description
2690874 LT23420, 23 Gross HP* & 42” Mower Deck
2690875 LT24460, 24 Gross HP* & 46” Mower Deck
2690995 LT23420, 23 Gross HP* & 42” Mower Deck
2690995-01 LT23420, 23 Gross HP* & 42” Mower Deck
2690996 LT24460, 24 Gross HP* & 46” Mower Deck
2690996-01 LT24460, 24 Gross HP* & 46” Mower Deck
2691089-00 LT20420, 20 Gross HP* & 42” Mower Deck
*See Speci cations for power rating information.
Mower Decks
Mfg. No. Description
1695602 42” Mower Deck
1695603 46” Mower Deck
AC130 Series
fr
Manuel d’utilisation
Not for
Reproduction
2
Not for
Reproduction
The Illustrated Parts List for this machine can be downloaded from www.allischalmerslawn.com. Please provide model
and serial number when ordering replacement parts.
Copyright © 2011 Briggs & Stratton Power Products Group, LLC
Milwaukee, WI, All rights reserved.
ALLIS-CHALMERS is a registered trademark of ALLIS-CHALMERS MANUFACTURING
COMPANY and is used under license.
TABLE OF CONTENTS
CONTENTS
Operator Safety ...................................................................................................4
Features and Controls ......................................................................................10
Operation ...........................................................................................................13
Safety Interlock System Tests ..........................................................................13
Maintenance ......................................................................................................16
Troubleshooting ................................................................................................ 19
Speci cations ....................................................................................................21
Parts and Accessories ......................................................................................21
Warranties ..........................................................................................................22
General Information
Thank you for purchasing this quality-built ALLIS-CHALMERS riding mower. We’re pleased that you’ve placed your
con dence in the ALLIS-CHALMERS brand. When operated and maintained according to the instructions in this manual,
your ALLIS-CHALMERS product will provide many years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with mowers and how
to avoid them. Because Briggs & Stratton Power Products Group, LLC does not necessarily know all the applications
this mower could be used for, it is important that you read and understand these instructions. Save these original
instructions for future reference.
ENGINE REFERENCE DATA
Model Description Name/Number
Unit MFG
Number
PRODUCT REFERENCE DATA
Unit SERIAL Number
Dealer Name
Date Purchased
Engine Make
Engine Type/Spec
Engine Model
Engine Code/Serial Number
Mower Deck MFG Number
Mower Deck SERIAL
Number
When contacting your authorized dealer for replacment
parts, service, or information you MUST have these
numbers.
Record your model name/number, manufacturer’s identi ca-
tion numbers, and engine serial numbers in the space pro-
vided for easy access. These numbers can be found in the
locations shown.
Product Identification Tag
Model / Modéle / Model xxxxxxxx
Serial / Sèrie / Serie xxxxxxxxxx
Briggs & Stratton Power Products Group, L.L.C.
Milwaukee, WI 53201 USA
Tractor ID Tag
Product Identi cation Tag
Product Reference Data
3
en
Not for
Reproduction
Operating Safety
Congratulations on purchasing a superior-quality piece of lawn and garden
equipment. Our products are designed and manufactured to meet or ex-
ceed all industry standards for safety.
Power equipment is only as safe as the operator. If it is misused, or not
properly maintained, it can be dangerous! Remember, you are responsible
for your safety and that of those around you.
Use common sense, and think through what you are doing. If you are not
sure that the task you are about to perform can be safely done with the
equipment you have chosen, ask a professional: contact your local autho-
rized dealer.
Read the Manual
The operator’s manual contains important safety information you
need to be aware of BEFORE you operate your unit as well as
DURING operation.
Safe operating techniques, an explanation of the product’s features
and controls, and maintenance information is included to help you
get the most out of your equipment investment.
Be sure to completely read the Safety Rules and Information found
on the following pages. Also completely read the Operation section.
Children
Tragic accidents can occur with children. Do not allow them
anywhere near the area of operation. Children are often at-
tracted to the unit and mowing activity. Never assume that
children will remain where you last saw them. If there is a
risk that children may enter the area where you are mowing,
have another responsible adult watch them.
DO NOT GIVE CHILDREN RIDES ON THIS UNIT! This
encourages them to come near the unit in the future while it
is running, and they could be seriously hurt. They may then
approach the unit for a ride when you are not expecting it,
and you may run over them.
Reverse
Do not mow in reverse unless abso-
lutely necessary. Always look down
and behind before and
while traveling in reverse
even with the mower
blades disengaged.
OPERATOR SAFETY
4
Not for
Reproduction
OPERATOR SAFETY
Slope Operation
You could be seriously injured or even killed if you use this unit on too
steep an incline. Using the unit on a slope that is too steep or where you
don’t have adequate traction can cause you to lose control or roll over.
A good rule of thumb is to not operate on any slope you cannot back up
(in 2-wheel drive mode). You should not operate on inclines with a slope
greater than a 3.5 ft (1,5 m) rise over a 20.0 ft (6,0 m) length. Always
drive up and down slopes: never cross the face.
Also note that the surface you are driving on can greatly impact stability
and control. Wet grass or icy pavement can seriously a ect your ability to
control the unit.
If you feel unsure about operating the unit on an incline, don’t do it. It’s
not worth the risk.
Moving Parts
This equipment has many moving parts that can injure you or someone else.
However, if you are seated in the seat properly, and follow all the rules in this
book, the unit is safe to operate.
The mower deck has spinning mower blades that can amputate hands and
feet. Do not allow anyone near the equipment while it is running!
To help you, the operator, use this equipment safely, it is equipped with an
operator-present safety system. Do NOT attempt to alter or bypass the system.
See your dealer immediately if the system does not pass all the safety interlock
system tests found in this manual.
Thrown Objects
This unit has spinning mower blades. These blades can pick up and throw debris
that could seriously injure a bystander. Be sure to clean up the area to be mowed
BEFORE you start mowing.
Do not operate this unit without the entire grass catcher or discharge guard (de-
ector) in place.
Also, do not allow anyone in the area while the unit is running! If someone does
enter the area, shut the unit o immediately until they leave.
Fuel and Maintenance
Gasoline is extremely ammable. Its vapors are also extremely ammable and
can travel to distant ignition sources. Gasoline must only be used as a fuel, not
as a solvent or cleaner. It should never be stored any place where its vapors can
build up or travel to an ignition source like a pilot light. Fuel belongs in an ap-
proved, plastic, sealed gas can, or in the tractor fuel tank with the cap securely
closed. Spilled fuel needs to be cleaned up immediately.
Proper maintenance is critical to the safety and performance of your unit. Be sure
to perform the maintenance procedures listed in this manual, especially periodi-
cally testing the safety system.
5
en
Not for
Reproduction
GENERAL OPERATION
1. Read, understand, and follow all instructions in the man-
ual and on the unit before starting.
2. Do not put hands or feet near rotating parts or under
the machine. Keep clear of the discharge opening at all
times.
3. Only allow responsible adults, who are familiar with the
instructions, to operate the unit (local regulations can
restrict operator age).
4. Clear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown by the blade(s).
5. Be sure the area is clear of other people before mowing.
Stop the unit if anyone enters the area.
6. Never carry passengers.
7. Do not mow in reverse unless absolutely necessary. Al-
ways look down and behind before and while travelling
in reverse.
8. Never direct discharge material toward anyone. Avoid
discharging material against a wall or obstruction. Ma-
terial may ricochet back toward the operator. Stop the
blade(s) when crossing gravel surfaces.
9. Do not operate the machine without the entire grass
catcher, discharge guard (de ector), or other safety de-
vices in place.
10. Slow down before turning.
11. Never leave a running unit unattended. Always disen-
gage the PTO, set parking brake, stop engine, and re-
move keys before dismounting.
12. Disengage blades (PTO) when not mowing. Shut o en-
gine and wait for all parts to come to a complete stop be-
fore cleaning the machine, removing the grass catcher,
or unclogging the discharge guard.
13. Operate the machine only in daylight or good arti cial
light.
14. Do not operate the unit while under the in uence of alco-
hol or drugs.
15 Watch for tra c when operating near or crossing road-
ways.
16. Use extra care when loading or unloading the unit into a
trailer or truck.
17. Always wear eye protection when operating this unit.
18. Data indicates that operators, age 60 years and above,
are involved in a large percentage of power equipment-
related injuries. These operators should evaluate their
ability to operate the equipment safely enough to protect
themselves and others from injury.
19. Follow the manufacturer’s recommendations for wheel
weights or counterweights.
20. Keep in mind the operator is responsible for accidents
occurring to other people or property.
21. All drivers should seek and obtain professional and
practical instruction.
22. Always wear substantial footwear and trousers. Never
operate when barefoot or wearing sandals.
23. Before using, always visually check that the blades and
blade hardware are present, intact, and secure. Re-
place worn or damaged parts.
24. Disengage attachments before: refueling, removing an
attachment, making adjustments (unless the adjustment
can be made from the operator’s position).
25. When the machine is parked, stored, or left unattended,
lower the cutting means unless a positive mechanical
lock is used.
26. Before leaving the operator’s position for any reason,
engage the parking brake (if equipped), disengage the
PTO, stop the engine, and remove the key.
27. To reduce re hazard, keep the unit free of grass,
leaves, & excess oil. Do not stop or park over dry
leaves, grass, or combustible materials.
28. It is a violation of California Public Resource Code Sec-
tion 4442 to use or operate the engine on or near any
forest-covered, brush-covered, or grass-covered land
unless the exhaust system is equipped with a spark ar-
rester meeting any applicable local or state laws. Other
states or federal areas may have similar laws.
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of
unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. This mowing
deck is capable of amputating hands and feet and throwing objects. The triangle in text signi es important
cautions or warnings which must be followed.
TRANSPORTING AND STORAGE
1. When transporting the unit on an open trailer, make sure
it is facing forward, in the direction of travel. If the unit is
facing backwards, wind lift could damage the unit.
2. Always observe safe refueling and fuel handling prac-
tices when refueling the unit after transportation or stor-
age.
3. Never store the unit (with fuel) in an enclosed poorly
ventilated structure. Fuel vapors can travel to an ignition
source (such as a furnace, water heater, etc.) and cause
an explosion. Fuel vapor is also toxic to humans and
animals.
4. Always follow the engine manual instructions for stor-
age preparations before storing the unit for both short
and long term periods.
5. Always follow the engine manual instructions for proper
start-up procedures when returning the unit to service.
6. Never store the unit or fuel container inside where there
is an open ame or pilot light, such as in a water heater.
Allow unit to cool before storing.
OPERATOR SAFETY
6
Not for
Reproduction
OPERATOR SAFETY
CHILDREN
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the unit
and the mowing activity. Never assume that children will re-
main where you last saw them.
1. Keep children out of the mowing area and under the
watchful care of another responsible adult.
2. Be alert and turn unit o if children enter the area.
3. Before and during reverse operation, look behind and
down for small children.
4. Never carry children, even with the blade(s) o . They
may fall o and be seriously injured or interfere with
safe unit operation. Children who have been given
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over by
the machine.
5. Never allow children to operate the unit.
6. Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
EMISSIONS
1. Engine exhaust from this product contains chemicals
known, in certain quantities, to cause cancer, birth de-
fects, or other reproductive harm.
2. Look for the relevant Emissions Durability Period and
Air Index information on the engine emissions label.
IGNITION SYSTEM
1. This spark ignition system complies with Canadian
ICES-002.
SLOPE OPERATION
Slopes are a major factor related to loss-of-control and tip-
over accidents, which can result in severe injury or death. Op-
eration on all slopes requires extra caution. If you cannot back
up the slope or if you feel uneasy on it, do not operate on it.
Control of a walk-behind or ride-on machine sliding on a
slope will not be regained by the application of the brake. The
main reasons for loss of control are: insu cient tire grip on
the ground, speed too fast, inadequate braking, the type of
machine is unsuitable for its task, lack of awareness of the
ground conditions, incorrect hitching and load distribution.
1. Mow up and down slopes, not across.
2. Watch for holes, ruts, or bumps. Uneven terrain could
overturn the unit. Tall grass can hide obstacles.
3. Choose a slow speed so that you will not have to stop or
change speeds while on the slope.
4. Do not mow on wet grass. Tires may loose traction.
5. Always keep unit in gear especially when traveling down
slopes. Do not shift to neutral and coast downhill.
6. Avoid starting, stopping, or turning on a slope. If tires
lose traction, disengage the blade(s) and proceed slowly
straight down the slope.
7. Keep all movement on slopes slow and gradual. Do
not make sudden changes in speed or direction, which
could cause the machine to rollover.
8. Use extra care while operating machines with grass
catchers or other attachments; they can a ect the stabil-
ity of the unit. Do not use on steep slopes.
9. Do not try to stabilize the machine by putting your foot
on the ground (ride-on units).
10. Do not mow near drop-o s, ditches, or embankments.
The mower could suddenly turn over if a wheel is over
the edge of a cli or ditch, or if an edge caves in.
11. Do not use grass catchers on steep slopes.
12. Do not mow slopes you cannot back up them.
13. See your authorized dealer/retailer for recommendations
of wheel weights or counterweights to improve stability.
14. Remove obstacles such as rocks, tree limbs, etc.
15. Use slow speed. Tires may lose traction on slopes even
through the brakes are functioning properly.
16. Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.
TOWED EQUIPMENT (RIDE-ON UNITS)
1. Tow only with a machine that has a hitch designed for
towing. Do not attach towed equipment except at the
hitch point.
2. Follow the manufacturer’s recommendations for weight
limit for towed equipment and towing on slopes.
3. Never allow children or others in or on towed equipment.
4. On slopes, the weight of the towed equipment may
cause loss of traction and loss of control.
5. Travel slowly and allow extra distance to stop.
6. Do not shift to neutral and coast down hill.
WARNING
Never operate on slopes greater than 17.6 percent (10°)
which is a rise of 3-1/2 feet (106 cm) vertically in 20 feet
(607 cm) horizontally.
When operating on slopes use additional wheel weights
or counterweights. See your dealer/retailer to determine
which weights are available and appropriate for your
unit.
Select slow ground speed before driving onto slope.
In addition to front weights, use extra caution when
operating on slopes with rear-mounted grass catchers.
Mow UP and DOWN the slope, never across the face,
use caution when changing directions and DO NOT
START OR STOP ON SLOPE.
7
en
Not for
Reproduction
SERVICE AND MAINTENANCE
Safe Handling of Gasoline
1. Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
2. Use only approved gasoline containers.
3. Never remove the gas cap or add fuel with the engine
running. Allow the engine to cool before refueling.
4. Never fuel the machine indoors.
5. Never store the machine or fuel container where there is
an open ame, spark, or pilot light such as near a water
heater or other appliance.
6. Never ll containers inside a vehicle or on a truck bed
with a plastic bed liner. Always place containers on the
ground away from your vehicle before lling.
7. Remove gas-powered equipment from the truck or
trailer and refuel it on the ground. If this is not possible,
then refuel such equipment on a trailer with a portable
container, rather than from a gasoline dispenser nozzle.
8. Keep nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete.
Do not use a nozzle lock-open device.
9. If fuel is spilled on clothing, change clothing immedi-
ately.
10. Never over- ll the fuel tank. Replace gas cap and
tighten securely.
11. Use extra care in handling gasoline and other fuels.
They are ammable and vapors are explosive.
12. If fuel is spilled, do not attempt to start the engine but
move the machine away from the area of spillage and
avoid creating any source of ignition until fuel vapors
have dissipated.
13. Replace all fuel tank caps and fuel container caps se-
curely.
Service & Maintenance
1. Never run the unit in an enclosed area where carbon
monoxide fumes may collect.
2. Keep nuts and bolts, especially blade attachment bolts,
tight and keep equipment in good condition.
3. Never tamper with safety devices. Check their proper
operation regularly and make necessary repairs if they
are not functioning properly.
4. Keep unit free of grass, leaves, or other debris build-
up. Clean up oil or fuel spillage. and remove any fuel-
soaked debris. Allow machine to cool before storage.
5. If you strike an object, stop and inspect the machine.
Repair, if necessary, before restarting.
6. Never make adjustments or repairs with the engine run-
ning.
7. Check grass catcher components and the discharge
guard frequently and replace with manufacturer’s rec-
ommended parts, when necessary.
8. Mower blades are sharp. Wrap the blade or wear
gloves, and use extra caution when servicing them.
9. Check brake operation frequently. Adjust and service
as required.
10. Maintain or replace safety and instructions labels, as
necessary.
11. Do not remove the fuel lter when the engine is hot as
spilled gasoline may ignite. Do not spread fuel line
clamps further than necessary. Ensure clamps grip
hoses rmly over the lter after installation.
12. Do not use gasoline containing METHANOL, gasohol
containing more than 10% ETHANOL, gasoline addi-
tives, or white gas because engine/fuel system damage
could result.
13. If the fuel tank must be drained, it should be drained out-
doors.
14. Replace faulty silencers/mu ers.
15. Use only factory authorized replacement parts when
making repairs.
16. Always comply with factory speci cations on all settings
and adjustments.
17. Only authorized service locations should be utilized for
major service and repair requirements.
18. Never attempt to make major repairs on this unit unless
you have been properly trained. Improper service pro-
cedures can result in hazardous operation, equipment
damage and voiding of manufacturer’s warranty.
19. On multiple blade mowers, take care as rotating one
blade can cause other blades to rotate.
20. Do not change engine governor settings or over-speed
the engine. Operating the engine at excessive speed
can increase the hazard of personal injury.
21. Disengage drive attachments, stop the engine, remove
the key, and disconnect the spark plug wire(s) before:
clearing attachment blockages and chutes, performing
service work, striking an object, or if the unit vibrates
abnormally. After striking an object, inspect the machine
for damage and make repairs before restarting and op-
erating the equipment.
22. Never place hands near the moving parts, such as a
hydro pump cooling fan, when the tractor is running.
(Hydro pump cooling fans are typically located on top of
the transaxle).
23. Units with hydraulic pumps, hoses, or motors: WARN-
ING: Hydraulic uid escaping under pressure may have
su cient force to penetrate skin and cause serious
injury. If foreign uid is injected into the skin it must be
surgically removed within a few hours by a doctor famil-
iar with this form of injury or gangrene may result. Keep
body and hands away from pin holes or nozzles that
eject hydraulic uid under high pressure. Use paper or
cardboard, and not hands, to search for leaks. Make
sure all hydraulic uid connections are tight and all hy-
draulic hoses and lines are in good condition before ap-
plying pressure to the system. If leaks occur, have the
unit serviced immediately by your authorized dealer.
24.
WARNING: Stored energy device. Improper release of
springs can result in serious personal injury. Springs
should be removed by an authorized technician.
25. Models equipped with an engine radiator: WARNING:
Stored energy device. To prevent serious bodily injury
from hot coolant or steam blow-out, never attempt to
remove the radiator cap while the engine is running.
Stop the engine and wait until it is cool. Even then, use
extreme care when removing the cap.
OPERATOR SAFETY
8
Not for
Reproduction
OPERATOR SAFETY
DANGER
Amputation Hazard
1704276
To avoid injury from rotating
blades, stay clear of deck edge.
DANGER
Amputation and
Thrown Objects Hazard
1704277
To avoid injury from rotating blades and
thrown debris, stay clear of deck edge
and discharge. Do not mow without
deflector or entire grass catcher in place.
Danger, Side
Discharge Models
Part No. 1704276
Danger, Side
Discharge Models
Part No. 1704277
Transmission
Release
Part No. 1730202
Danger, Main Panel
Part No. 1734879
Ignition Switch
Positions
Part No. 1722806
Height of Cut
Part No. 1730264
Decal Locations
9
en
1730264
173xxxx
Not for
Reproduction
Figure 1
FEATURES AND CONTROLS
Tractor Controls
Throttle/Choke Control
(Choke-A-Matic)
The throttle/choke controls the engine speed and choke
(see Figure 1). Move the throttle/choke control to the
FAST position to increase engine speed and SLOW
position to decrease engine speed. Always operate at full
throttle. Move the throttle/choke control to the CHOKE
position for starting a cold engine. A warm engine may
not require choking.
Headlights
The light switch turns the tractor headlights on and o .
Reverse Mowing Option (RMO)
The Reverse Mowing Option allows for mowing (or use of
other PTO driven attachments) while traveling in reverse.
If you choose to mow or operate another attachment in
reverse, turn the RMO key after the PTO is engaged. The
L.E.D. light will illuminate, and the operator can then mow in
reverse. Each time the PTO is disengaged the RMO needs
to be reactivated if desired.
10
Not for
Reproduction
FEATURES AND CONTROLS
PTO Switch
The PTO (Power Take-O ) switch engages and disen-
gages attachments that use the PTO. To engage the PTO,
pull UP on the switch. Push DOWN to disengage. Note that
the operator must be seated fi rmly in the tractor seat for
the PTO to function.
Ignition Switch
The ignition switch starts and stops the engine, it has three
positions:
OFF Stops the engine and shuts o the
electrical system.
RUN Allows the engine to run and powers the
electrical system.
START Cranks the engine for starting.
NOTE: Never leave the ignition switch in the RUN position
with the engine stopped–this drains the battery.
Ground Speed Pedals
The tractor’s forward ground speed is controlled by the
forward ground speed control pedal. The tractor’s reverse
ground speed is controlled by the reverse ground speed
control pedal.
Depressing either pedal will increase ground speed. Note
that the further down the pedal is depressed, the faster the
tractor will travel.
Cruise Control
The cruise control is used to lock the ground speed control
in forward. The cruise control has ve lock positions.
Mower Height of Cut Adjustment
The cutting height lift lever controls the mower cutting
height. The cutting height has seven positions between 1.5”
and 4.0” (3,8 and 10,2 cm).
Seat Adjustment Lever
The seat can be adjusted forward and back. Move the
lever, position the seat as desired, and release the lever
to lock the seat into position.
Transmission Release Lever
The transmission release lever deactivates the trans-
mission so that the tractor can be pushed by hand. See
Pushing the Tractor by Hand section.
Fuel Tank
To remove the cap, turn counterclockwise.
Fuel Level Gauge
Displays the fuel level in the tank.
Parking Brake
The parking brake knob is used to lock the parking brake
when the tractor is stopped. Fully depressing the brake
pedal and pulling up on the knob engages the parking
brake.
Brake Pedal
Depressing the brake pedal applies the tractor brake.
11
en
Not for
Reproduction
FEATURES AND CONTROLS
Parking Brake Function
Applying the Parking Brake - See Figure 2. To lock the
parking brake, release the ground speed pedals (A), fully
depress the brake pedal (B), pull UP on the parking brake
knob (C), and then release brake pedal.
Releasing the Parking Brake - See Figure 2. To release
the parking brake, fully depress the brake pedal (B) and
push the parking brake knob (C) DOWN.
Figure 2
B
C
D
Cruise Control
TO ENGAGE:
1. Pull up on the cruise control knob (D, Figure 2).
2. Depress the forward ground speed pedal (A).
3. Lift up the cruise control knob (D) when desired speed
is reached. The Cruise will lock in one of its ve lock-
ing positions.
TO DISENGAGE:
1. Depress the brake pedal (B).
OR
2. Depress the forward ground speed pedal (A).
A
12
Not for
Reproduction
OPERATION
Adding Fuel
WARNING
Fuel and its vapors are extremely ammable
and explosive.
Fire or explosion can cause severe burns or
death.
When Adding Fuel
Turn engine o and let engine cool at least 3
minutes before removing the fuel cap.
Fill fuel tank outdoors or in well-ventilated area.
Do not over ll fuel tank. To allow for expansion of
the fuel, do not ll above the bottom of the fuel tank
neck.
Keep fuel away from sparks, open ames, pilot
lights, heat, and other ignition sources.
Check fuel lines, tank, cap, and ttings frequently
for cracks or leaks. Replace if necessary.
If fuel spills, wait until it evaporates before starting
engine.
1. Remove the fuel cap (A, Figure 3).
2. Fill the tank. Do not over ll. Leave room in the tank for
fuel expansion. Refer to your Engine Manual for speci c
fuel recommendations.
3. Install and hand tighten the fuel cap.
Starting the Engine
WARNING
Fuel and its vapors are extremely ammable
and explosive.
Fire or explosion can cause severe burns or
death.
When Starting Engine
Ensure that spark plug, mu er, fuel cap and air
cleaner (if equipped) are in place and secured.
Do not crank engine with spark plug removed.
If engine oods, set choke (if equipped) to OPEN/RUN
position, move throttle (if equipped) to FAST position
and crank until engine starts.
WARNING
If the unit does not pass a safety test, do not
operate it. See your authorized dealer.
Safety Interlock System Tests
This unit is equipped with a Safety Interlock System. Do
not attempt to bypass or tamper with the switches and
devices.
Test 1 — Engine should NOT crank if:
• PTO switch is ON, OR
• Brake pedal is NOT fully depressed (parking brake
OFF), OR
• The cruise control lever is NOT in NEUTRAL.
Test 2 — Engine SHOULD crank if:
• PTO switch is OFF, AND
• Brake pedal is fully depressed (parking brake ON),
AND
• The cruise control lever is in NEUTRAL.
Test 3 — Engine should SHUT OFF if:
• Operator rises o seat with PTO engaged, OR
• Operator rises o seat with brake pedal NOT fully de-
pressed (parking brake OFF).
Test 4 — Check Mower Blade Stopping Time
Mower blades and mower drive belt should come to a
complete stop within ve seconds after electric PTO
switch is turned OFF. If mower drive belt does not stop
within ve seconds, see an authorized dealer.
Test 5 — Check Reverse Mow Option (RMO)
• Engine should shut o if reverse travel is attempted
if the PTO has been switched on and RMO has not
been activated.
• RMO light should illuminate when RMO has been ac-
tivated.
NOTE: Once the engine has stopped, the PTO switch
must be turned off after the operator returns to the seat
in order to start the engine.
13
en
Not for
Reproduction
OPERATION
WARNING
Mowing in reverse can be hazardous to bystanders.
Tragic accidents can occur if the operator is not
alert to the presence of children. Never activate
RMO if children are present. Children are often
attracted to the unit and the mowing activity.
1. Sit in the seat and lift UP the seat adjustment lever, po-
sition the seat as desired, and release the lever to lock
the seat in position.
2. Fully depress the brake pedal or set the parking brake
with pedal fully depressed, pull UP on parking brake
knob, then release pedal.
3. Disengage PTO switch by pushing IN.
4. Set the throttle/choke control to the CHOKE position.
5. Insert the ignition key and turn clockwise to the START
position and release the key as soon as the engine
starts.
6. After the engine starts, move the throttle/choke control
to half speed. Warm up the engine by running it for at
least 30 seconds.
7. Set throttle/choke control to the FAST position.
NOTE: In the event of an emergency, the engine can be
stopped by turning the ignition switch to STOP. For nor-
mal engine shut down, follow the procedure in “Stopping
the Tractor & Engine.”
WARNING
Engines give o carbon monoxide, an
odorless, colorless, poison gas.
Breathing carbon monoxide can cause
nausea, fainting or death.
Start and run engine outdoors.
Do not start or run engine in enclosed area, even if
doors or windows are open.
Mowing
1. Set the mower cutting height to the desired level using
the mower lift lever.
2. Engage the parking brake. Make sure the PTO switch is
disengaged.
3. Start the engine (see Starting the Engine).
4. Set the throttle/choke control to the FAST position.
5. Engage the PTO to activate the mower blades.
6. Begin mowing.
7. When nished, shut o the PTO and raise the deck
using the mower lift lever.
8. Stop the engine (see Stopping the Tractor and
Engine).
WARNING
The engine will shut o if the reverse ground speed
pedal is depressed while the PTO is on and the
RMO has not been activated. The operator should
always turn the PTO o prior to driving across
on roads, paths or any area that maybe used by
other vehicles. Sudden loss of drive could create a
hazard.
Driving the Tractor
1. Sit in the seat and adjust the seat so that you can com-
fortably reach all the controls and see the dashboard
display.
2. Engage the parking brake.
3. Make sure the PTO switch is disengaged.
4. Start the engine (see Starting the Engine).
5. Disengage the parking brake and release the brake
pedal.
6. Depress the forward ground speed control pedal to
travel forward. Release the pedal to stop. Note that the
further down the pedal is depressed the faster the trac-
tor will travel.
7. Stop the tractor by releasing the ground speed control
pedals, setting the parking brake, and stopping the en-
gine (see Stopping the Tractor and Engine).
Mowing in Reverse (RMO)
If an operator chooses to mow in reverse, the RMO system
can be used. To use the Reverse Mowing Option (RMO)
turn the RMO key after the PTO is engaged. The L.E.D.
light will illuminate, and the operator can then mow in re-
verse. Each time the PTO is engaged the RMO needs to
be reactivated if desired. The key should be removed to
restrict access to the RMO feature.
14
Not for
Reproduction
OPERATION
Pushing the Tractor by Hand
1. Disengage the PTO and turn the engine o .
2. Push the lever approximately 2.3/8” (6 cm) to release
the transmission (B, Figure 3).
3. The tractor can now be pushed by hand.
DO NOT TOW TRACTOR
Towing the unit will cause transmission dam-
age.
Do not use another vehicle to push or pull
this unit.
Do not actuate the transmission release
valve lever while the engine is running.
Figure 3
B
A
Figure 5
Attaching a Trailer
The maximum horizontal drawbar force allowed is 280
Newton. The maximum vertical drawbar force is 160
Newton. This equates to a 250 lbs (113 kg) trailer on a 10
degree hill. Secure the trailer with an appropriately sized
clevis pin (A, Figure 5) and clip (B).
Figure 4
Adjusting Mower Cutting Height
The cutting height lift lever (A, Figure 4) controls the
mower cutting height. The cutting height has seven posi-
tions between 1.5” and 4.0” (3,8 and 10,2 cm).
A
Stopping the Tractor and Engine
1. Return the ground speed control(s) to NEUTRAL.
2. Disengage the PTO and wait for all moving parts to
stop.
3. Move the throttle/choke control to the SLOW position.
4. Turn the ignition key to OFF. Remove the key.
WARNING
Fuel and its vapors are extremely
ammable and explosive.
Fire or explosion can cause severe burns
or death.
Do not choke the carburetor to stop engine.
113 kg
(250 lbs.)
1 m
(3 pies
4 pulg.)
6 m (20 pies)
A
B
15
en
Not for
Reproduction
MAINTENANCE
Check Mower Blade Stopping Time
Mower blades and mower drive belt should come to a com-
plete stop within ve seconds after the electric PTO switch
is turned o .
1. With tractor in neutral, PTO disengaged and operator in
seat, start the engine.
2. Look over the left-hand footrest at the mower drive belt.
Engage the PTO and wait several seconds. Disengage
the PTO and check the amount of time it takes for the
mower drive belt to stop.
3. If mower drive belt does not stop within ve seconds,
see an authorized dealer.
Check Tire Pressure
Tire pressure should be checked periodically, and maintained
at the levels shown in the chart. Note that these pressures may
di er slightly from the “Max In ation” stamped on the side-wall
of the tires. The pressures shown provide proper traction, im-
prove cut quality, and extend tire life.
Size PSI bar
15 x 6.0-6 12-14 0,82-0,96 bar
20 x 10.0-8 10 0,68 bar
Maintenance Chart
TRACTOR AND MOWER
Every 8 Hours or Daily
Check safety interlock system
Clean debris o tractor and mower deck
Clean debris from engine compartment
Every 25 Hours or Annually *
Check mower blade stopping time
Check tractor and mower for loose hardware
Check tire pressure
Every 50 Hours or Annually *
Check tractor brakes
Clean battery and cables
See Dealer Annually to
Lubricate tractor and mower
Check mower blades **
* Whichever comes rst
** Check blades more often in regions with sandy soils or
high dust conditions.
ENGINE
First 5 Hours
Change engine oil - see engine manual
Every 8 Hours or Daily
Check engine oil level - see engine manual
Every 25 Hours or Annually *
Clean engine air lter and pre-cleaner **
Every 50 Hours or Annually *
Change engine oil
Replace oil lter
Annually
Replace air lter
Replace pre-cleaner
See Dealer Annually to
Inspect mu er and spark arrester
Replace spark plug
Replace fuel lter
Clean engine air cooling system
* Whichever comes rst
** Clean more often in dusty conditions or when airborne
debris is present.
16
Not for
Reproduction
MAINTENANCE
Cleaning the Battery and Cables
1. Disconnect the cables from the battery, negative
cables rst (A, Figure 6) then the cover and positive
cables (B).
2. Loosen the wingnut and washer (D).
3. Pivot the hold-down rod (C) up and away from battery.
Secure to steering tower.
4. Remove the battery (E).
5. Clean the battery compartment with a solution of bak-
ing soda and water.
6. Clean the battery terminals and cable ends with a wire
brush and battery terminal cleaner until shiny.
7. Reinstall the battery in the battery compartment.
Secure with the battery hold-down rod and wingnut
and washer.
8. Re-attach the battery cables, positive cables and cover
rst then the negative cables.
9. Coat the cable ends and battery terminals with petro-
leum jelly or non-conducting grease.
WARNING
When removing or installing battery cables,
disconnect the negative cable FIRST and
reconnect it LAST. If not done in this order,
the positive terminal can be shorted to the
frame by a tool.
Battery Maintenance
Battery Charging
WARNING
Keep open ames and sparks away from
the battery; the gasses coming from it are
highly explosive. Ventilate the battery well
during charging.
A dead battery or one too weak to start the engine may be
the result of a defect in the charging system or other electri-
cal component. If there is any doubt about the cause of the
problem, see your dealer. If you need to replace the battery,
see the Cleaning the Battery and Cables section.
To charge the battery, follow the instructions provided by
the battery charger manufacturer as well as all warnings
included in the Operator Safety section of this manual.
Charge the battery until fully charged. Do not charge at a
rate higher than 10 amps.
Figure 6
D
E
C
A
B
Seat Adjustment
The seat can also be adjusted forward and back. Move the
lever (A, Figure 7), position the seat as desired, and re-
lease the lever to lock the seat into position.
A
Figure 7
17
en
Not for
Reproduction
MAINTENANCE
Storage
WARNING
Never store the unit (with fuel) in an
enclosed, poorly ventilated structure. Fuel
vapors can travel to an ignition source (such
as a furnace, water heater, etc.) and cause
an explosion. Fuel vapor is also toxic to
humans and animals.
When Storing Fuel Or Equipment With Fuel In Tank
Store away from furnaces, stoves, water heaters or
other appliances that have pilot lights or other ignition
sources because they can ignite fuel vapors.
Equipment
Disengage the PTO, set the parking brake, and remove
the key.
Battery life will be increased if it is removed. Put in a cool,
dry place and fully charged about once a month. If the bat-
tery is left in the unit, disconnect the negative cable.
Fuel System
Fuel can become stale when stored over 30 days. Stale
fuel causes acid and gum deposits to form in the fuel sys-
tem or on essential carburetor parts. To keep fuel fresh,
use Briggs & Stratton FRESH START® fuel stabilizer,
available as a liquid additive or a drip concentrate car-
tridge.
There is no need to drain gasoline from the engine if a fuel
stabilizer is added according to instructions. Run the en-
gine for 2 minutes to circulate the stabilizer throughout the
fuel system. The engine and fuel can then be stored up to
24 months.
If gasoline in the engine has not been treated with a fuel
stabilizer, it must be drained into an approved container.
Run the engine until it stops from lack of fuel. The use of a
fuel stabilizer in the storage container is recommended to
maintain freshness.
Engine Oil
While the engine is still warm, change the engine oil. See
Engine Manual.
Before starting the unit after it has been stored:
Check all uid levels. Check all maintenance items.
• Perform all recommended checks and procedures
found in this manual.
• Allow the engine to warm up for several minutes before
use.
18
Not for
Reproduction
TROUBLESHOOTING
PROBLEM LOOK FOR REMEDY
Engine will not turnover
or start.
Brake pedal not depressed. Fully depress brake pedal.
PTO (electric clutch) switch is in
ON position.
Place in OFF position.
Cruise control engaged. Move knob to NEUTRAL/OFF position.
Out of fuel. If engine is hot, allow it to cool, then refi ll the fuel tank.
Engine fl ooded. Disengage the choke.
Fuse is blown. See authorized dealer.
Battery terminals require
cleaning.
See Cleaning the Battery and Cables section.
Battery discharged or dead. Recharge or replace battery.
Wiring loose or broken. Visually check wiring. If wires are frayed or broken, see authorized dealer.
Solenoid or starter motor faulty. See authorized dealer.
Safety interlock switch faulty. See authorized dealer.
Water in fuel. See authorized dealer.
Gas is old or stale. See authorized dealer.
Engine starts hard or runs
poorly.
Fuel mixture too rich. Clean air fi lter.
Engine has other problem. See authorized dealer.
Engine knocks.
Low oil level. Check/add oil as required.
Using wrong grade oil. See Engine Manual.
Excessive oil consumption.
Engine running too hot. See authorized dealer.
Using wrong grade oil. See Engine Manual.
Too much oil in crankcase. Drain excess oil.
Engine exhaust is black.
Dirty air fi lter. See Engine Manual.
Choke closed. Open choke.
Engine runs, but tractor will
not drive.
Ground speed control pedals
not depressed.
Depress pedals.
Transmission release lever in
PUSH position.
Move into DRIVE position.
Parking brake is engaged. Disengage parking brake.
Traction drive belt is broken or
slipping.
See authorized dealer.
Troubleshooting the Tractor
19
en
Not for
Reproduction
20
TROUBLESHOOTING
PROBLEM LOOK FOR REMEDY
Brake will not hold.
Internal brake worn. See authorized dealer.
Tractor steers hard or
handles poorly.
Steering linkage is loose. See authorized dealer.
Improper tire infl ation. See Check Tire Pressure section.
Front wheel spindle bearings
dry.
See authorized dealer.
Troubleshooting the Tractor (Continued)
PROBLEM LOOK FOR REMEDY
Mower will not raise.
Lift linkage not properly attached
or damaged.
See authorized dealer.
Mower cut is uneven.
Mower not leveled properly. See authorized dealer.
Tractor tires not properly
infl ated.
See Check Tire Pressure section.
Mower cut is rough
looking.
Engine speed too slow. Set to full throttle.
Ground speed too fast. Slow down.
Mower has other problem. See authorized dealer.
Engine stalls easily with
mower engaged.
Engine speed too slow. Set to full throttle.
Ground speed to fast. Slow down.
Dirty or clogged air fi lter. See Engine Manual.
Cutting height set too low. Cut tall grass at maximum cutting height during fi rst pass.
Engine not up to operating
temperature.
Run engine for several minutes to warm-up.
Starting mower in tall grass. Start the mower in a cleared area.
Excessive mower vibration.
Mower has other problem. See authorized dealer.
Engine runs and tractor
drives, but mower will not
drive.
PTO not engaged. Engage the PTO.
Mower has other problem. See authorized dealer.
Troubleshooting the Mower
Not for
Reproduction
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Allis-Chalmers 2691089-00 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur