GE Appliances GNE21FMKES Guide d'installation

Refrigerators

Bottom Freezer

238C5511P001 Pub No. 49-60758 02-16 GE

Write the model and serial

numbers here:

Model # ____________________

Serial # ____________________

Find these numbers on a label

on the left side, near the middle

of the refrigerator compartment.

Owner’s Manual and

Installation Instructions

GE, GE Profile and GE Café

Models 21, 24 & 25 cuft

Safety Instructions ............2, 3

Operating Instructions

Features ..........................4, 5

Controls ..........................6, 7

Dispenser ...........................8

Water Filter .........................9

Shelves and Bins ...................10

Pans ...............................11

Freezer ........................12, 13

Automatic Ice maker ...............14

Care and Cleaning ................ 15

Replacing the Lights ................16

Installation Instructions

Preparing to Install the

Refrigerator ........................17

Appliance Dimensions ..............18

Installing the Refrigerator .......19-32

Installing the Water Line ........33-35

Troubleshooting Tips ......37, 38

Normal Operating Conditions .......36

Service - Truth or Myth .........39, 40

Consumer Support

Warranty ..........................41

MWF Water Filter Cartridge Limited

Warranty ........................43

Performance Data Sheet ...........42

Consumer Support ........Back Cover

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

2

GE Appliances website

For more information on your refrigerator’s operation, visit www.GEAppliances.com or call

800.GECARES (800.432.2737). In Canada visit GEAppliances.ca or call 800.561.3344.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All

safety messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words are

defined as:

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

REFRIGERATOR SAFETY INFORMATION

SAFETY

WARNING

DANGER

CAUTION

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, explosion, electric shock, or injury when using your

refrigerator follow these basic safety precautions:

WARNING

 Do not clean glass shelves or covers with warm water

when they are cold. Glass shelves and covers may break if

exposed to sudden temperature changes or impact, such

as bumping or dropping. Tempered glass is designed to

shatter into many small pieces if it breaks.

 Keep fingers out of the “pinch point” areas; clearances

between the doors and between the doors and cabinet are

necessarily small. Be careful closing doors when children

are in the area.

 Do not refreeze frozen foods which have thawed

completely.

 Do not touch the cold surfaces in the freezer compartment

when hands are damp or wet, skin may stick to these

extremely cold surfaces.

 In refrigerators with automatic icemakers, avoid contact

with the moving parts of the ejector mechanism, or with

the heating element that releases the cubes. Do not place

fingers or hands on the automatic ice making mechanism

while the refrigerator is plugged in.

 Use a sturdy glass when dispensing ice (on models with ice

dispenser

To reduce the risk of injury when using your refrigerator, follow these basic

safety precautions.

 This refrigerator must be properly installed and located in

accordance with the Installation Instructions before it is

used.

 Unplug the refrigerator before making repairs, replacing a

light bulb, or cleaning.

Note: Power to the refrigerator cannot be disconnected by

any setting on the control panel.

Note: Repairs must be performed by a qualified service

professional.

 Replace all parts and panels before operating.

 Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

 Because of potential safety hazards under certain

conditions, we strongly recommend against the use of an

extension cord. However, if you must use an extension cord,

it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA certified (in Canada), 3-wire grounding type

appliance extension cord having a grounding type plug

and outlet and that the electrical rating of the cord be 15

amperes (minimum) and 120 volts.

 To prevent suffocation and entrapment hazards to

children, remove the fresh food and freezer doors from any

refrigerator before disposing of it or discontinuing its use.

 Do not allow children to climb, stand or hang on the door

handles or the shelves in the refrigerator. They could

seriously injure themselves.

CAUTION

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

3

WARNING

Explosion Hazard.

Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can

result in fire, explosion, or death.

INSTALLATION

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall outlet to minimize the

possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly

grounded.

Where a standard 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to have

it replaced with a properly grounded 3-prong wall

outlet. Do not use an adapter.

The refrigerator should always be plugged into its own

individual electrical outlet which has a voltage rating

that matches the rating plate.

A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded

electrical supply is required. This provides the best

performance and also prevents overloading house

wiring circuits which could cause a fire hazard from

overheated wires.

Never unplug your refrigerator by pulling on the power

cord. Always grip plug firmly and pull straight out from

the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the wall, be

careful not to roll over or damage the power cord.

CONNECTING ELECTRICITY

WARNING

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet

Do not remove the ground prong

Do not use an adapter

Failure to follow these instructions can result in

death, fire, or electrical shock.

SAFETY (CONT.)

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

WARNING

Suffocation and child entrapment hazard.

Remove fresh-food and freezer doors from the refrigerator, prior to disposal. Failure to do so can

result in child entrapment which can lead to death or brain damage.

Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are

still dangerous even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator,

please follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old Refrigerator or

Freezer:

 Take off the fresh food and freezer doors.

 Leave the shelves in place so that children may

not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an old

refrigeration product, check with the company

handling the disposal about what to do.

PROPER DISPOSAL OF YOUR OLD REFRIGERATOR

IMPORTANT:

Space-saving ice maker (on some models)

Ice maker and bin are located on the door creating

more usable storage space.

LED lighting

LED lights in the fresh food compartment are located

at the top center and on the left and right sides of

climate zone pans. LED lights are also located in the

freezer; see pages 12 and 13.

Full-width drawer

A full-width drawer that can accommodate larger

items is located at the bottom of the fresh food

compartment.

QuickSpace™ shelf (on some models)

Functions as a normal full-sized shelf when needed

and easily slides back to store tall items below.

Removable/adjustable door bins

Can be moved up or down to accommodate your

needs.

Climate zone drawers

Separate pans for produce storage.

Water filter

Accessible for easy replacement.

4

About the features.

French Door Models

Floating snack pan

Can be moved to different locations to best serve your

needs.

LED lighting

LED light is located at the top of the fresh food

compartment. LED lights are also located in the

freezer; see pages 12 and 13.

Full-width shelves

Full-width shelves that can accommodate larger items.

Full-width gallon door bins

Nonadjustable full-width door bins that will hold gallon

containers.

Climate zone pans

Separate bins for produce storage.

Water filter (on some models)

Accessible for easy replacement.

Adjustable door bins

Can be moved up or down to accommodate your

needs.

Icemaker (on some models)

Icemaker is located in the freezer on some models.

Icemaker Kit IM-4D is available for models that are

icemaker-ready.

5

Single Door Models

6

About the controls.

Figure A

Figure B

Knob Position Temperature Guide

Refrigerator Freezer

Coldest 34°F (1.1°C) Coldest -6°F (-21.1°C)

Colder 37°F (2.8°C) Colder 0°F (-17.8°C)

Cold 44°F (6.7°C) Cold 6°F (-14.4°C)

Note: Do not block air outlet by placing food items

directly against it. Erratic temperatures may result.

Freezer Compartment Temperature Control

Adjust freezer compartment temperature. The freezer

temperature is preset in the factory at the Colder

position. Allow 24 hours for temperature to stabilize to

the preset recommended setting.

Fresh Food Compartment Temperature Control

Adjust fresh food compartment temperature. The fresh

food temperature is preset in the factory at the Colder

position. Allow 24 hours for temperature to stabilize to

the preset recommended setting.

NOTE: Power to the refrigerator cannot be disconnected by

any setting on the control panel.

Freezer Compartment Temperature Control

Adjust freezer compartment temperature. The freezer

temperature is preset in the factory at 0°F. Allow

24 hours for temperature to stabilize to the preset

recommended setting.

Fresh Food Compartment Temperature Control

Adjust fresh food compartment temperature. The fresh

food temperature is preset in the factory at 37°F. Allow

24 hours for temperature to stabilize to the preset

recommended setting.

Water Filter

Press and hold 3 seconds to reset the Water Filter.

Turbo Cool

To set the TurboCool™, press the Turbo Cool pad for 3

seconds. The display will show tc.

TurboCool™ rapidly cools the refrigerator compartment

in order to more quickly cool foods. Use TurboCool™

when adding a large amount of the food to the

refrigerator compartment, putting away foods after

they have been sitting out at room temperature, or

when putting away warm leftovers. It can also be used if

the refrigerator has been without power for an extended

period.

NOTE: The refrigerator temperature cannot be

changed during TurboCool™. The freezer temperature

is not affected during TurboCool. When opening the

refrigerator door during TurboCool™, the fans will

continue to run if they have cycled on.

Door Alarm

To set the alarm, press the Door Alarm pad. This alarm

will sound if either door is open for more than 2 minutes.

The beeping stops when you close the door.

NOTE: To put the refrigerator control in the OFF position,

simultaneously touch the words Freezer and Fridge for 3

seconds. Power to the refrigerator cannot be disconnected

by any setting on the control panel.

GBE21, ABE21 Internal Control

GDE21, PDE21, GNE21, PNE21, GDE25, GNE25, PNE25, CNE25 Top Control

NOTE: The refrigerator is shipped with protective film covering the temperature controls.

If this film was not removed during installation, remove it now.

Figure C

7

Freezer Compartment Temperature Control

Adjust freezer compartment temperature. The freezer

temperature is preset in the factory at 0°F. Allow

24 hours for temperature to stabilize to the preset

recommended setting.

Fresh Food Compartment Temperature Control

Adjust fresh food compartment temperature. The fresh

food temperature is preset in the factory at 37°F. Allow

24 hours for temperature to stabilize to the preset

recommended setting.

Water Filter

Press and hold 3 seconds to reset the Water Filter.

Turbo Cool

To set the TurboCool™, press the Alarm pad for 3

seconds. The display will show tc.

TurboCool™ rapidly cools the refrigerator compartment

in order to more quickly cool foods. Use TurboCool™

when adding a large amount of the food to the

refrigerator compartment, putting away foods after

they have been sitting out at room temperature, or

when putting away warm leftovers. It can also be used if

the refrigerator has been without power for an extended

period.

NOTE: The refrigerator temperature cannot be

changed during TurboCool™. The freezer temperature

is not affected during TurboCool. When opening the

refrigerator door during TurboCool™, the fans will

continue to run if they have cycled on.

Alarm

Press the Alarm pad to toggle the door alarm between

off and on. The alarm will sound if either door is left open

for more than 2 minutes. The beeping stops when you

close the door.

Lock

Press and hold the Lock pad for 3 seconds to lock out

ice and water dispenser and all other controls. Press and

hold to unlock the controls.

LED dispenser Light

Press the Light pad to turn your dispenser light on and

off.

NOTE: To put the refrigerator control in the OFF position,

simultaneously touch the words Freezer and Fridge

for 3 seconds. Power to the refrigerator cannot be

disconnected by any setting on the control panel.

GFE24, PFE24, CFE24 External Control

8

About the dispenser. (on some models)

Press the glass gently against the dispenser cradle.

The spill shelf is not self-draining. To reduce water spotting, the

shelf should be cleaned regularly.

If no water is dispensed when the refrigerator is first installed,

there may be air in the water line system. Press the dispenser

paddle for at least five minutes to remove trapped air from the

water line and to fill the water system. To flush out impurities in

the water line, throw away the first six full glasses of water.

WARNING

Laceration Hazard

 Never put fingers or any other object into ice crusher

discharge opening. Doing so can result in contacting the ice

crushing blades and lead to serious injury or amputation

 Use a sturdy glass when dispensing ice. A delicate glass may

break and result in personal injury.

To remove Dispenser Tray



Pull Dispenser Tray out.

To reinstall Dispenser Tray



Push in until it is firmly in place.

Door Ice Bin

1. Open left fresh food door.

2. Pull down latch to release bin

door.

3. Using handhold, lift ice bucket

up and out to clear locators in

bottom of bin.

4. To replace the ice bucket, set

it on the guide brackets and

push until the ice bucket seats

properly.

5. If bucket cannot be replaced,

rotate the Ice Bucket Fork 1/4

turn clockwise.

Water & Ice Dispenser

(See About the controls)

Internal Water Dispenser

(on some models)

The water dispenser is located on the left wall inside the

refrigerator compartment.

To dispense water:

1. Hold the glass against the recess.

2. Push the water dispenser button.

3. Hold the glass underneath the dis-

penser for 2–3 seconds after releas-

ing the dispenser button. Water may

continue to dispense after the button

is released.

If no water is dispensed when the

refrigerator is first installed, there may be air in the water line

system. Press the dispenser button for at least 5 minutes to

remove trapped air from the water line and to fill the water

system. During this process, the dispenser noise may be loud

as the air is purged from the water line system. To flush out

impurities in the water line, throw away the first 6 glassfuls of

water.

NOTE: To avoid water deposits, the dispenser should be

cleaned periodically by wiping with a clean cloth or sponge.

Important Facts About Your Dispensers



Do not add ice from trays or bags to the door ice maker

bucket. It may not crush or dispense.



Avoid overfilling glass with ice and use of narrow glasses.

Backed-up ice can jam the chute or cause the door in the

chute to freeze shut. If ice is blocking the chute remove the ice

bucket, poke it through with a wooden spoon.



Beverages and foods should not be quick-chilled in the

door ice maker bin. Cans, bottles or food packages in the

storage drawer may cause the ice maker or auger to jam.



To keep dispensed ice from missing the glass, put the glass

close to, but not touching, the dispenser opening.



Some crushed ice may be dispensed even though you

selected CUBED ICE. This happens occasionally when a few

cubes accidentally get directed to the crusher.



After crushed ice is dispensed, some water may drip from the

chute.



Sometimes a small mound of snow will form on the door in the

ice chute. This condition is normal and usually occurs when you

have dispensed crushed ice repeatedly. The snow will eventually

evaporate.

Dispenser

Tray

Ice bucket

fork

Latch

Ice bucket

9

About the GE Appliances

®

MWF water filter cartridge.

Water Filter Cartridge

The water filter cartridge is located in back upper right

corner of the refrigerator compartment.

When to replace the filter on models with a

replacement indicator light

There is a replacement indicator light for the water filter

cartridge on the dispenser. A red light will start blinking to tell

you that you need to replace the filter soon.

The filter cartridge should be replaced when the replacement

indicator light turns red or if the flow of water to the dispenser

or icemaker decreases.

When to replace the filter on models without a

replacement indicator light

The filter cartridge should be replaced every six months

or earlier if the flow of water to the dispenser or icemaker

decreases.

Removing the filter cartridge

If you are replacing the cartridge, first remove the old one by

slowly turning it to the left. Do not pull down on the cartridge.

A small amount of water may drip down.

NOTE: To reduce the risk associated with property damage

due to water leakage, read and follow instructions before

installation and use of this system. Installation and use MUST

comply with all sate and local plumbing codes.

CAUTION

If air has been trapped in the system,

the filter cartridge may be ejected as it is removed. Use

caution when removing.

Installing the Filter Cartridge

1. Fill the replacement cartridge with water from the tap to

allow for better flow from the dispenser immediately after

installation.

2. Line up the arrow on the cartridge and the cartridge holder.

Place the top of the new cartridge up inside the holder. Do

not push it up into the holder.

3. Slowly turn it to the right until the filter

cartridge stops. DO NOT OVERTIGHTEN. As

you turn the cartridge, it will automatically

raise itself into position. The cartridge will

move about a 1/2 turn.

4. Run water from the dispenser for 1-1/2

gallons (about three minutes) to clear the

system and prevent sputtering.

5. Press and hold the RESET WATER FILTER pad (on some

models) on the dispenser for three seconds.

NOTE: A newly installed water filter cartridge may cause water

to spurt from the dispenser.

Filter Bypass Plug

You must use the filter bypass plug when a replacement filter

cartridge is not available. The dispenser and the icemaker will

not operate without the filter or filter bypass plug.

WARNING

To reduce the risk associated with choking, do not allow children under 3 years of age to have access to small parts

during the installation of this product. The disposable filter cartridge should be replaced every 6 months at the rated

capacity, or sooner if a noticeable reduction in flow rate occurs.

For the maximum benefit of your filtration system, GE recommends the use of GE-branded filters only. Using GE-branded

filters in GE and Hotpoint

®

refrigerators provides optimal performance and reliability. GE filters meet rigorous industry NSF

standards for safety and quality that are important for products that are filtering your water. GE has not qualified non-GE-

branded filters for use in GE and Hotpoint refrigerators and there is no assurance that non-GE-branded filters meet GE’s

standards for quality, performance and reliability.

If you have questions, or to order additional filter cartridges, visit our website at www.gewaterfilters.com or call

GE Parts and Accessories, 800.626.2002 (Canada 1.800.626.2002 or geappliances.ca/en/products/parts-filters-

accessories or call 1.800.661.1616).

Cartridge

Holder

Filter Bypass

Plug

SmartWater

Rearranging the Refrigerator Shelves

Shelves in the refrigerator compartment are adjustable.

To remove the shelves:

1. Remove all items from the

shelf.

2. Tilt the shelf up at the front.

3. Lift the shelf up at the back

and bring the shelf out.

To replace the shelves:

1. While tilting the shelf up, insert the top

hook at the back of the shelf in a slot on

the track.

2. Lower the front of the shelf until the

bottom of the shelf locks into place.

Adjustable Door Bins (on some models)

To remove: Lift the bin straight up; then pull out.

To replace: Engage the bin in the molded supports on the door

and push down to lock in place.

Non-Adjustable Gallon Door Bins (on some models)

To remove: Lift the bin straight up; then pull out.

To replace: Engage the bin in the molded supports on the door

and push down to lock in place.

10

About the shelves and bins

Not all features are on all models.

Quick Space Shelf (on some models)

This shelf splits in half

and slides under itself for

storage of tall items on the

shelf below.

This shelf can be removed

and replaced or relocated.

NOTE: The back half of the

Quick Space Shelf is not

adjustable.

Climate Zone Pans

Keep fruits and vegetables organized in separate compartments

for easy access. Excess water that may accumulate in the

bottom of the drawers or under the drawers should be wiped

dry.

To remove pan:

Slide the pan out to the stop position, lift the pan up and past

the stop position and pull forward

Floating Snack Pan (on some models)

This pan can be moved to the most useful location for your

family’s needs.

To remove, slide the pan out to the stop position, lift the pan up

and past the stop position and lift it out.

Full -Width Pan (on some models)

To remove pan:

1. Pull the pan out to the stop position.

2. Lift the front of the drawer up and out.

To replace pan:

1. Place back of the drawer in first and rotate drawer front

down to seat it on the slides.

2. Push the drawer in to the closed position.

How to Remove and Replace Drawer Divider

To remove:

1. Pull the drawer out to the stop position.

2. Slide pan divider to right to release it from pan.

To replace:

Reverse steps 1 and 2 to replace drawer divider.

11

About the pans.

Not all features are on all models.

12

About the freezer drawer. (on some models)

FREEZER BASKETS

1. An ice bucket in the top basket

(on some models).

2. A top full-width basket.

3. A bottom full-width basket (with

divider - in some models).

NOTE: Do not fill baskets higher than

the rim of the basket. This may cause

baskets to stick or jam when opening

or closing.

Top Basket Removal

To remove the top full-width basket on freezer drawer

models:

1. Pull the basket out to the stop location.

2. Lift basket up to release it from the slides.

When replacing the basket, make sure that the basket remains

mounted on the side rails and over the slides of the bottom

basket.

NOTE: Always be sure to fully close this basket.

Bottom Basket Removal

To remove the bottom full-width basket on freezer drawer

models:

1. Open the bottom freezer drawer until it stops.

2. Remove the top freezer basket.

3. The bottom freezer basket rests on the inside tabs on the

drawer slides.

4. Lift the front of the basket and pull forward.

5. Release the pin from the slot to remove the basket.

When replacing the bottom full-width basket, tilt the basket

back and lower it into the drawer. Rotate the basket to a

horizontal position and press down. Make sure to place the pin

back into the slot.

NOTE: Always be sure that the basket is seated on the bracket

tabs before sliding the drawer back into the freezer.

Not all features are on all models.

Appearance and

features may vary

1

2

3

Ice Bucket

(on some models)

LED lights are located

on both sides of the

freezer

Top Basket

Bottom

Basket

13

About the freezer compartment. (on some models)

FREEZER SHELF AND BASKET

1. A full-width fixed wire shelf

2. A full-width sliding plastic basket

NOTE: Do not fill baskets higher

than the rim. This may cause

basket to stick or jam when

opening or closing.

Basket Removal

To remove the full-width sliding basket on freezer door

models:

1. Open the basket out to its full extension.

2. Lift up the front of the basket and pull straight out to remove.

When replacing the basket, insert the plastic basket into the

lower liner rails and push back into place.

Fixed Shelf Removal

NOTE: The full-width wire shelf is not intended to slide.

To remove for cleaning, push the shelf to one side while then

pull up on the opposite side and out to remove.

To replace the full-width wire shelf, insert one side of the

shelf into the supports, pushing the shelf to that side until the

opposite side will fit into its supports.

Not all features are on all models.

1

2

LED lights are located

on both sides of the

freezer

14

About the automatic ice maker.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Automatic Ice maker (on some models)

The ice maker will produce seven cubes per cycle approximately

100–130 cubes in a 24-hour period, depending on freezer

compartment temperature, room temperature, number of door

openings and other use conditions.

If the refrigerator is operated before the water connection is

made to the ice maker, set the power switch in the OFF position.

When the refrigerator has been connected to the water supply,

set the power switch to the ON position.

The ice maker will fill with water when it cools to 15°F (–10°C).

A newly installed refrigerator may take 12 to 24 hours to begin

making ice cubes.

You may hear a buzzing sound each time the ice maker fills with

water.

Throw away the first few batches of ice to allow the water line to

clear.

Be sure nothing interferes with the sweep of the feeler arm.

When the bin fills to the level of the feeler arm, the ice maker will

stop producing ice. It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes will become cloudy,

taste stale and shrink.

NOTE: In homes with

lower-than-average water

pressure, you may hear the

ice maker cycle multiple

times when making one

batch of ice.

For Refrigerator Models with Ice Maker in the Door

Ice Bucket and Dispenser

• Open the ice box door on inside of the left door.

• Pull up and out on the ice bucket in the left hand door to

remove it from the compartment .

• To replace the ice bucket, set it on the guide brackets and

push until the ice bucket seats properly.

• If bucket cannot be replaced, rotate the ice bucket fork 1/4

turn clockwise.

• Ice maker can be turned on and off using this display (see

About the controls on pages 6 and 7.)

For Refrigerator Models with Ice Maker in the Freezer Compartment

Some models come with an ice maker installed in the

freezer compartment. For those models that come ice-

maker ready, you can purchase Kit IM-4D. Visit our website

at GEAppliances.com or call GE Parts and Accessories,

800.626.2002 (in Canada visit geappliances.ca/en/products/

parts-filters-accessories or call 1.800.661.1616).

There is ice storage in the freezer compartment located on

the left side of the upper basket. Pull the upper basket for-

ward to remove the ice bucket.

WARNING

To minimize the risk of personal injury, avoid contact with the moving parts of the ejector mechanism, or with the

heating element that releases the cubes. Do not place fingers or hands on the automatic ice making mechanism while

the refrigerator is plugged in.

Ice bucket fork

Latch

Ice bucket

Ice maker

Feeler Arm

Power

Switch

Green

Power Light

Ice bucket

15

Care and cleaning of the refrigerator.

Cleaning the Outside

The stainless steel panels, door handles and trim.

Do not use appliance wax, polish, bleach, or other products

containing chlorine on stainless steel.

Stainless steel can be cleaned with a commercially available

stainless steel cleaner. A spray-on stainless steel cleaner

works best.

Silver-accented plastic parts.

Wash parts with soap or other mild detergents. Wipe clean with

a sponge, damp cloth or paper towel.

Do not use scouring pads, powdered cleaners, bleach or

cleaners containing bleach because these products can

scratch and weaken the paint finish.

Should spill tray need cleaning use lime remover.

Cleaning the Inside

Unplug the refrigerator before cleaning.

If this is not practical, wring excess moisture out of sponge or

cloth when cleaning around switches, lights or controls.

Use an appliance wax polish on the inside surface between

the doors.

8VHZDUPZDWHUDQGEDNLQJVRGDVROXWLRQ³DERXWD

tablespoon (15 ml) of baking soda to a quart (1 liter) of water.

This both cleans and neutralizes odors. Rinse and wipe dry.

Behind the Refrigerator

Be careful when moving the refrigerator away from the wall. All

types of floor coverings can be damaged, particularly cushioned

coverings and those with embossed surfaces.

Raise the leveling legs located at the bottom front of the

refrigerator.

Pull the refrigerator straight out and return it to position by

pushing it straight in. Moving the refrigerator in a side direction

may result in damage to the floor covering or refrigerator.

Lower the leveling legs until they touch the floor.

When pushing the refrigerator back, make sure you don’t

roll over the power cord or water supply line.

For long vacations or absences, remove food and unplug the

refrigerator. Clean the interior with a baking soda solution of

one tablespoon (15 ml) of baking soda to one quart (1 liter) of

water. Leave the doors open.

If the temperature can drop below freezing, have a qualified

service technician drain the water supply system to prevent

serious property damage due to flooding.

1) Turn refrigerator off (pages 6 and 7) or unplug the refrigerator.

2) Empty ice bucket

3) Turn water supply off

If you cut the water supply off, turn off the ice maker (pg. 14).

Upon returning from vacation:

1) Replace the water filter.

2) Run 2 gallons of water through the cold water dispenser

(about 5 minutes) to flush the system.

Preparing for Vacation

Preparing to Move

Secure all loose items such as shelves and drawers by taping

them securely in place to prevent damage.

When using a hand truck to move the refrigerator, do not rest

the front or back of the refrigerator against the hand truck. This

could damage the refrigerator.

Handle only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright position during

moving.

CAUTION

Do not clean glass shelves or covers

with warm water when they are cold. Glass shelves and

covers may break if exposed to sudden temperature changes

or impact such as bumping or dropping. Tempered glass is

designed to shatter into many small pieces if it breaks.

16

Replacing the lights

Refrigerator Lights (LEDs)

There is LED lighting in the fresh food compartment at the

top center and on the left and right sides above the climate

zone pans on the french door models. LED lighting is located

at the top of the fresh food compartment on the single door

models.

LED lights are also located at the top of the left and right

sides of the freezer in all models.

An authorized technician will need to replace the LED light.

If this assembly needs to be replaced, call GE Service at

1.800.432.2737 in the United States or 1.800.561.3344

in Canada.

LEDs (locations

may vary by

model)

17

TOOLS YOU MAY NEED

Installation

Refrigerator

Instructions

Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com

In Canada, call 1.800.561.3344 or visit our Website at: www.GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT ³ Observe all governing codes

and ordinances. Save these instructions for local

inspector’s use.

•

Note to Installer – Be sure to leave these instructions

with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – Refrigerator Installation

20 minutes

Water Line Installation

30 minutes

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

PREPARATION

MOVING THE REFRIGERATOR INDOORS

If the refrigerator will not fit through a doorway, the

refrigerator door and freezer drawer or door can be

removed.

• To remove the refrigerator door, see Step 1 in the

Reversing the Door Swing section.

• To remove the freezer drawer, see the Removing the

Freezer Drawer section.

WATER SUPPLY TO THE ICE MAKER AND DISPENSER

If the refrigerator has an ice maker, it will have to be

connected to a cold water line. A GE water supply kit

(containing tubing, shutoff valve, fittings and instructions)

is available at extra cost from your dealer, by visiting our

website at GEAppliances.com (in Canada at

www.GEAppliances.ca) or from Parts and Accessories,

800.626.2002 (in Canada 1.800.661.1616).

Adjustable Wrench

1/4” Outer Diameter

Compression Nut

and Ferrule (sleeve)

(ice maker models only)

Phillips-Head Screwdriver

Ȓµ and ȓµSocket

Ratchet/Driver

3/32”, 1/8” & 3/16” Allen

Wrenches

Pencil

1/8” Drill Bit and

Electric or Hand Drill

Tape Measure

1/4” Nut Driver

Wire Cutters

Level

Torx T20, Driver

18

Installation Instructions

MEASURE THE CABINET OPENING

ACCORDING TO THE WIDTH OF THE

REFRIGERATOR

Measure width of cabinet opening where

refrigerator will be placed, B.

Be sure to account for any countertop overhang,

baseboard thickness and any clearance desired.

Width, B, should not be less than 30”-33”

(depending on model). The refrigerator will be

placed approximately in the middle of this opening.

Back Wall

Front

Right

Side

REFRIGERATOR

B

Baseboard

Thickness or

Countertop

Overhang

(Whichever Is

Larger) Plus

Any Desired

Clearance

ITEM 21 cuft

models with

single door

21 cuft

models with

french doors

25 cuft

models with

single door

24/25 cuft

models with

french doors

A* 69-7/8” 69-7/8” 69-7/8” 67-7/8”

B 30” 30” 33” 33”

C** 36-1/8” 36-3/8” 37-3/8” 37-1/8”

D** - 54” 54-3/4” 54-3/4”

E 55” 54-7/8” 60-1/2” 60-1/2”

F 45-5/8” 37” 48” 38-3/4”

G 33-7/8” 34-3/8” 34-7/8” 35-3/8”

H 61” 45-7/8” 65” 48-3/8”

I** 33-1/2” 37-5/8” 36” 40-1/2”

NOTE:

* The height of the refrigerator to the top of the door.

** Includes the handle.

A

C

G

D

E

F

I

H

F

B

A

C

D

B

155Û

I

H

90Û

APPLIANCE DIMENSIONS

Single Door Models with

Fresh Food and Freezer Doors

(some models)

Single Door Models

with Drawer (some models)

French Door Models

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature will go

below 60°F (16°C) because it will not run often enough to

maintain proper temperatures.

• Do not install the refrigerator where the temperature will go

above 100°F (37°C) because it will not perform properly.

• Do not install the refrigerator in a location exposed to water (rain,

etc.) or direct sunlight.

• Install it on a floor strong enough to support it fully loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air

circulation and plumbing and electrical connections.

Sides 1/8” (3 mm)

Top 1” (25 mm) Cabinet/Hinge Cover

Back 2” (50 mm)

19

IMPORTANT NOTES

This refrigerator without the handles ranges from 34” to

35-1/4” depending on your model (see dimension G on the

previous page). Doors and passageways leading to the

installation location must be at least

36”

in order to leave the

doors attached to the refrigerator while transporting it into

the installation location. If passageways are less than 36”, the

refrigerator doors can easily be scratched and damaged. The

doors can be removed to allow the refrigerator to be safely

moved indoors.

• If you need to remove the door and you have the french

door model, see Removing the French Doors on page 20.

• If you need to remove the door and you have the single

fresh food door model, see Reversing the Door on page 26.

• To remove the freezer door and you have the model with a

freezer drawer see Removing Freezer Drawer on page 24.

• If you have the model with the hinged freezer door see

Reversing the Door on page 26.

• If it is NOT necessary to remove doors, skip to Step 6. Leave

tape and all packaging on doors until the refrigerator is in

the final location. Once in place, install door handles (see

Steps 1 and 2).

• SKID REMOVAL: Tilt refrigerator to each side to remove

skid.

• NOTE: Use a padded hand truck to move this refrigerator.

Place the refrigerator on the hand truck with a side against

the truck. We strongly recommend that TWO PEOPLE move

and complete this installation.

ATTACH FRESH FOOD HANDLE(S)

Attach the handle to the mounting fasteners by

aligning the slots on the handle with the mounting

fasteners. Slide the handle down until you hear a

“click”.

NOTE: For French Door models, follow the same

procedure for both doors.

1

ATTACH FREEZER HANDLE

Attach the handle to the mounting fasteners by

aligning the slots on the handle with the mounting

fasteners. Slide the handle to the right until you hear

a “click”.

2

Mounting

Fasteners

Mounting

Fasteners

20

Installation Instructions

IMPORTANT NOTES

When removing french doors:

• Read the instructions all the way through before

starting.

• Handles are included inside the refrigerator.

• Place the screws by their related parts to avoid

using them in the wrong places.

• Provide a non-scratching work surface for the

doors.

CAUTION

Lifting Hazard. Single person lift can cause injury.

Use assistance when handling, moving or lifting the

refrigerator doors.

NOTE: When moving door, to prevent damage to

door and electronics carefully place the door in a

proper location.

WARNING

To eliminate the risk of electric shock or injury during

installation, you must first unplug the refrigerator

before proceeding. Failure to follow these instructions

can result in electrical shock.

REMOVING FRENCH DOORS (on some models)

Tape the doors shut with adhesive tape.

1

REMOVING RIGHT DOOR

A. Remove the hinge cover on top of the right

fresh food door by removing the screw using

a Phillips screwdriver.

B Using a 5/16” socket ratchet/driver, remove

the bolts securing the top hinge to the cabinet.

Lift the hinge support straight up to free the

hinge pin from the socket in the top of the

door.

C. Remove the tape from the right door and tilt

the door away from the cabinet. Lift the door

off the center hinge pin.

D. Set the door on a non-scratching surface with

the inside up.

2

REMOVING LEFT DOOR

A. For Ice and Water Models Only: Unplug the

water line from the back of the refrigerator

and remove all tape that fixes the water line

to the refrigerator.

La page charge ...

GE Appliances GNE21FMKES Guide d'installation

GE Appliances GNE21FMKES Guide d'installation

dans d''autres langues

Documents connexes

Autres documents