WilsonPro Pro 70 Plus (75Ω) Guide d'installation

Marque
WilsonPro
Modèle
Pro 70 Plus (75Ω)
Catégorie
Amplificateurs de signal cellulaire
Taper
Guide d'installation
ENGLISH
FRANÇAIS
Contents:
How Cellular Boosters Work .........................................1
Install Overview ...................................................1
Kit Options .......................................................2
Installation Diagram .............................................3 & 4
Outside Antenna Installation .........................................5
Installing the Inside Antenna(s) .......................................7
Installing The Signal Booster .........................................7
Finding The Strongest Signal ........................................8
Post Install Setup / LCD Screen ......................................9
Warnings and Recommendations ....................................12
Warranty .......................................................14
Specifications ............................................Back Cover
Note: This manual contains important safety and operating information. Please read and follow the
instructions in this manual. Failure to do so could result in damage to your Signal Booster.
Appearance of device and accessories may vary.
INSTALLATION GUIDE
In-Building
SmarTech
®
Cellular Signal Boosters
PRO 70 PLUS
™
PRO SERIES
1
2
Contact Wilson Electronics Customer Support Team with any questions at
866-839-9361 or email: [email protected]
ENGLISH
1. Select a location on the roof or outside of the building to install the outside antenna. Refer
to pages 3 & 5.
2. Select a location to install the Signal Booster that is away from excessive heat,
direct sunlight or moisture, and has adequate ventilation. Airtight enclosures are not
recommended. Booster should be as close to the outside antenna as possible in order to
minimize losses from cable length to outside antenna.
Install Overview
Refer to Installation Diagram on page 3 & 4. Contact Wilson Electronics Technical Support
Team with any questions at 866-839-9361.
How a Cellular Booster Improves Indoor Signals
Wilson cellular signal booster systems work as follows: an outdoor antenna placed
on a
building where some cell signal is present, (ideally on a roof or pole), receives and sends
that weak signal via coax cable (like used in satellite TV installs) to a signal booster located
indoors. That weak signal is amplified by the booster and delivered via coax cable to an
inside antenna(s) which rebroadcasts the amplified signal within one or several areas where
improved signal is required. Signals from indoor cell device(s) are likewise picked up by the
inside antenna(s), amplified by the signal booster and transmitted back to the cell tower via
the outside antenna. The improved signals result in reliable cellular connections for indoor
users.
About Gain and Improved Signal Area
The less signal strength at the outside antenna’s location and/or the greater the coverage
need, the more gain will be required. Conversely, the more signal present outside, the
greater the inside coverage area will be. Proper aiming of the outside antenna towards the
source of the cell signal is also important. The gains of the outside and inside antenna,
though reduced by losses from coax cable lengths, also affect area of improved coverage.
Placement of the inside antenna is also a factor as they have directional characteristics.
Inside wall materials will also affect indoor coverage area.
Another important factor affecting coverage area is inadequate isolation between outside
and inside antenna(s). Wilson boosters are designed to reduce their internal gain in
order to prevent any feedback “oscillations” which if unchecked, could affect nearby cell
site operation. The LCD status display on the booster is used to determine if a booster
is operating at optimal gain for each cellular band. Optimal gain can be achieved by
increasing antenna separation, i.e. isolation, until the max gain is indicated. If attainable
separation is limited by a building’s layout, gain will suffer. A nearby cell site, even if not
providing service to a user, can also cause the booster’s automatic network protection
circuitry to reduce gain or even turn off one or more of the booster’s bands so as to
prevent signal overload to the nearby site. The display on the booster can also be used
to determine if this condition is taking place. Refer to pages 9-11 for explanation of the
booster status display.
1
2
Contact Wilson Electronics Customer Support Team with any questions at
866-839-9361 or email: [email protected]
ENGLISH
Pro 70 Plus
2’ RG11 Lightning Surge
Protector
Wide Band Directional
Antenna 75’ RG11
Wide Band Panel Antenna
50' RG11
460127 Kit
460227 Kit
Pro 70 Plus
AC/DC
Power Supply
12V/3A
AC/DC
Power Supply
12V/3A
2’ RG11 Lightning Surge
Protector
Wide Band Directional
Antenna 75' RG11
4G Dome Ceiling Antenna
50’ RG11
3. Connect the cable from the outside antenna to the signal booster’s “outside antenna”
connector. Refer to page 6 for more information on running cable. Lightning Surge
Protection is recommended for all in-building installations. Refer to pages 3 & 6.
4. Select a location for the inside antenna. Try to choose a position in the center of the area
needing improved signal. Keep in mind that proper inside antenna to outside antenna
isolation is necessary for the system to function properly. This may require as much as
50 to 75 feet of horizontal separation from the outside antenna. Vertical separation
also helps increase isolation. Alternate means of isolation are possible. If physical
separation is not possible, please contact Wilson Electronics Tech Support at 866-839-
9361 for suggestions on alternate methods to achieve isolation.
5. Connect the cable from the inside antenna to the signal booster’s “inside antenna”
connector. Refer to page 6 for more information on running cable. Keep cable runs as
short as possible to reduce signal loss in the system.
6. Before powering up the signal booster, verify that both the outside antenna and the
inside antenna are connected correctly, and check that all connections are tight. Note:
Be careful when plugging the connectors in so as not to bend the center pins on the
connectors.
7. Power on the signal booster by plugging in the included power supply. If the lights are
not green, please refer to pages 9-11.
Multiple Kit Options Available Note: Kits may contain different accessories
To purchase Expansion Kits call Wilson Electronics Sales Department at: 888-503-5329
3
4
Contact Wilson Electronics Customer Support Team with any questions at
866-839-9361 or email: [email protected]
ENGLISH
Installation Diagram
Spacing Critical
Outside Antenna
(Wide Band Directional
Antenna shown)
Inside Antenna
Power Supply
Inside Antenna
Preferred Method: Place the
Inside Antenna in the ceiling
facing down for the best
coverage.
Note: A Wilson Lightning Surge Protector
(859902) is recommended for all building
installations. Make sure the protector is
installed outside the building at point of entry
connected to a suitable ground and in line
between the Outside Antenna and the Signal
Booster.
Surge Protector
Power Strip
3
4
Contact Wilson Electronics Customer Support Team with any questions at
866-839-9361 or email: [email protected]
ENGLISH
Signal
Booster
Optional Inside
Antenna for added
coverage
Optional Splitter
2-way or 3-way, when using
multiple inside antennas for
increased coverage
5
6
Contact Wilson Electronics Customer Support Team with any questions at
866-839-9361 or email: [email protected]
ENGLISH
Cell Tower
Wide Band Antenna
Selecting a Location for the Outside Antenna
The outside antenna must be mounted at a location outside of the home or building, where the
strongest cell signal is present. This can be accomplished by using the Wilson Signal Meter.
Alternatively, a cell phone in test mode can be used for finding the area around the building
with the strongest signal.
Mount the outside antenna as high as possible facing towards the suspected location of the
cell tower and pointing away from the expected location of the inside antenna(s).
Outside Antenna Installation
The antenna should be mounted as shown in Figure 1. The mounting bracket, included with
antenna, is adjustable and will accommodate pipe diameters from 1.25 inches to 2 inches
(pipe sold separately #901117). Mount the antenna so that there is at least 3 feet of clearance
in all directions around it. Make sure the antenna is not pointing across your own roof or at
the inside antenna as this will cause the cell site protection circuitry to shut down the signal
booster.
Signal Booster
Outdoor
Antenna
Outdoor
Antenna
Inside
Antenna
Figure 1
Figure 2
CORRECT INSTALLATION
Never point antennas toward each otherPoint antennas away from each other
INCORRECT INSTALLATION
Inside
Antenna
Signal Booster
5
6
Contact Wilson Electronics Customer Support Team with any questions at
866-839-9361 or email: [email protected]
ENGLISH
Warning:
Lightning protection is recommended for all installations (#859902-
50 Ohm, shown below). Take extreme care to ensure that neither
you nor the antenna comes near any electric power lines.
Installing Lightning Protection
Install the Lightning Surge Protector (LSP) outside, in line with the coax cable from the outside
antenna, near where the coax cable from the outside antenna will enter the building. Connect
the Outside antenna cable to one of the connectors of the surge protector. Connect the other
connector on the LSP to the cable entering the building. Ensure the LSP is properly grounded
as close to the LSP as possible (ground wire not included).
Running Outside Antenna Cable
If you are mounting the outside antenna to the outside wall of your home or building, the
simplest way is to run the cable on the outside of the wall and attach it to the exterior of your
home or office. Then drill a hole through the wall where you want the cable to appear on the
inside of the building. Before drilling, make sure that there are no electrical outlets, sewer
or water pipes, or electrical wiring in the wall that you are about to drill through as this could
potentially harm you or damage the building. Note: Existing TV cables already being used
for another purpose can not be shared with the cell booster installation.
After drilling the required hole, run the cable through and seal it with cable bushings or a
silicone-type sealant to enclose the hole that you have created. In some instances, it may be
possible to run the cable up into the fascia of the attic overhang. In this circumstance, the cable
will be accessible in the attic for further routing.
Exterior wall of building or home
Lightning
Surge Protector
Signal Booster
Surge Protector Power Strip
To Outside
Antenna
Ground Wire
To Inside
Antenna
7
8
Contact Wilson Electronics Customer Support Team with any questions at
866-839-9361 or email: [email protected]
ENGLISH
Installing the Inside Antenna(s)
Select a location for the inside antenna, preferably in the center of where the signal needs
to be amplified. A minimum separation distance of 20 vertical feet and or 50 horizontal feet
between the inside and outside antenna(s) may be necessary in order to achieve full booster
gain and therefore maximum indoor coverage. If the amplifier can not be set to maximum
gain as explained on page 10, you may need as much as 75 feet of horizontal separation, or
mechanical isolation, between inside and outside antennas. Refer to installation diagram on
pages 3 & 4.
Some installations requiring signal improvement in far areas of larger homes or structures
may require multiple inside antennas and splitter(s). For example if signal is improved
in most areas of a structure, but yet there is weak signal In another area, the signal from
the booster can be split to two or more separate indoor antennas by using a splitter (sold
separately). Refer to the configuration on pages 3 & 4.
Additional Inside Panel
Antenna w/ cable
sold separately
Multiple mounting options
available
For additional antenna options
see pages 14 & 15
Splitter Options:
2-way
(859993)
3-way
(859994)
4-way
(859106)
Installing the Signal Booster
Select a location for the signal booster which is away from excessive heat, direct sunlight,
moisture and is not subject to high temperatures. Do not place the signal booster in an air-tight
enclosure. Recommended installation locations for in-building signal boosters are in a closet or on
a shelf where power is available. Attic installations may expose the booster to high heat.
Note: Do not install in areas subject to temperatures in excess of 150 °F.
If installing Dome Antenna or Panel Antenna,
you must have 20 vertical feet or 50 horizantal
feet of separation.
7
8
Contact Wilson Electronics Customer Support Team with any questions at
866-839-9361 or email: [email protected]
ENGLISH
Note: Maintain at least 6 inches of clearance from surrounding objects. Be careful when plugging
the connector in so as not to damage the center pins on the connectors.
Run the outside antenna cable to the signal booster and attach it to the connector labeled
“Outside Antenna” on the signal booster. Run the inside antenna cable to the signal booster and
attach it to the connector labeled “Inside Antenna” on the signal booster.
Note: In order to abide by FCC regulations, cable lengths and antennas shipped as a kit with each
booster must be used and not cut and shortened. Contact our tech support for cable kits to be used
in situations requiring long cable runs.
Note: It is very important to power your signal booster using a surge protected AC power strip with
at least a 1000 Joule rating. Failure to do this will void your warranty in the event of a power surge
or lightning strike.
Finding the Strongest Signal
When installing your signal booster’s outside antenna, aiming it towards the best signal
source from your carrier is important. The best way of getting the strongest signal is to
use the Wilson Signal Meter and accessory Directional Antenna (see outside antenna kit
options on pages 13-14), an alternate way is to have one person on the roof to rotate the
outside antenna, which is connected to the signal booster. Turn the outside antenna about
45 degrees at a time, while the second person, inside the building, is watching the signal
strength on a signal meter (preferred) or a phone in test mode. This allows you to read the
signal strength from the cell tower. The phone should be in the test mode so the actual
signal strength can be read, as bars are not the most accurate. Always make sure the
person inside the building gives the signal strength time to register on the phone (at least
30 seconds for phone to update the signal reading).
-50 dBm0 dBm -60 dBm -70 dBm -80 dBm -90 dBm -100dBm -110dBm
EXCELLENT GOOD POOR NO
SIGNAL
Signal Strength Graph
Cell Tower
Cell Signal
Outside
Antenna
Signal readings usually appear as a negative number (for example, -86). The closer the
number to zero, the stronger the signal (see Signal Srength Graph above).
9
10
Contact Wilson Electronics Customer Support Team with any questions at
866-839-9361 or email: [email protected]
ENGLISH
Post Install Setup
The Pro Series booster is designed with advanced internal programming which allows it to
automatically adjust itself for a variety of conditions and still boost weak signals. After completing
the amplifier installation, the LCD display and push button on the lower panel of the Pro Series
booster is used to verify the final gain that the booster adjusted itself to produce after antennas
have been placed. The display can also be used (if necessary) to re-adjust antennas so the
booster can produce maximum gain and therefore, coverage. The LCD screen will show status
for each band and inform the installer if any bands may have had their gain reduced by the
booster’s internal programming. In addition, an indicator light on the booster's upper panel will
help diagnose the overall status of the booster by glowing in different colors. This will be covered
in the following page.
The Pro Plus booster has an integrated graphical meter to simplify the installation process. This is
not to replace your signal meter - rather it complements the use. The bar graphs will assist in the
aiming of your outside antenna - the biggest graph indicates that you are receiving the best overall
signal.
To access this feature for the currently displayed frequency band, press and hold the "Band
Select" button for 2 seconds. This will change the display to the UL/DL bar graph (uplink/
downlink). A quick press of the button will move to the next band (briefly showing the band, before
returning back to the bar graph); while holding the button will return to the regular display.
UL
DL
press and hold
for 2 seconds
Understanding the LCD Screen
1. Four bands can be individually selected:
The 700 MHz LTE Bands (B12/17 and B13)
OK
9
10
Contact Wilson Electronics Customer Support Team with any questions at
866-839-9361 or email: [email protected]
ENGLISH
The 800 MHz Band
– Cell Band
The 1900 MHz
– PCS Band
1700/2100 MHz
– AWS Band
OK
OK
OK
The single “BAND SELECT” button is used to scroll the display through the four
cellular bands in order to verify that each band is functioning properly. An asterisk (located next
to the band selected) will flash if one or more bands have been turned down/off by the boosters
control circuitry due to strong nearby cell site signal overload (“OVL”) and/or oscillation detection
(“OSC”) from antennas being too close. This is no cause for concern if the power light remains
green and you are satisfied with your indoor coverage area.
Understanding the Upper Panel Indicator Light
As the LCD display is being toggled through the four cellular bands, the upper indicator
light (power) will glow green, orange, or red on each selected band, depending on how the
booster is functioning on each band as explained below.
PRO 70 PLUS
Green indicates the unit is powered and working properly.
Red indicates the booster has shut down due to extreme oscillation (feedback).
Orange indicates the booster has shut down due to extreme signal overload. This is caused
from being too close to a cell tower.
11
12
Contact Wilson Electronics Customer Support Team with any questions at
866-839-9361 or email: [email protected]
ENGLISH
Fixing Red Light Issues
If the power light is red:
1. Make sure all connections are tight.
2. You need to increase the distance between the outside antenna and the inside antenna
by moving them horizontally and/or vertically farther apart. After doing so, reset the
booster by unplugging the power supply and then plugging it back in. If the light is
green after separating the antennas, you have eliminated the problem.
3. If your coverage area is still too small after separating the antennas contact the Wilson
Electronics Customer Support Team for assistance: 866-839-9361.
Fixing Orange Light Issues
If the power light is orange:
1. It will be necessary to turn the outside antenna away from the nearby cellular signal
in small increments until the light turns green. If the Signal Booster will not respond,
relocation of the outside antenna may be required.
2. If the light remains orange, contact the Wilson Electronics Customer Support Team for
assistance at 866-839-9361.
About Wilson Electronics
Wilson Electronics, LLC has been a leader in the wireless communications industry for over
40 years. The company designs and manufactures Signal Boosters, antennas and related
components that significantly improve cellular telephone signal reception and transmission
in a wide variety of applications, mobile (marine, RV, vehicles) and in-building (home, office,
machine to machine).
With extensive experience in antenna and Signal Booster research and design, the company’s
engineering team uses a state-of-the-art testing laboratory, including an anechoic chamber
and network analyzers, to fine-tune antenna designs and performance. For its Signal Boosters,
Wilson Electronics uses a double electrically shielded RF enclosure and cell tower simulators
for compliance testing.
Wilson Electronics Signal Boosters feature patented SmarTech
®
that enables them to
automatically adjust their power based on cell tower requirements. By detecting and preventing
oscillation (feedback), signal overload and interference with other users, these SmarTech
®
Signal Boosters improve network cell phone areas without compromising carrier systems.
All products are engineered and assembled in the company’s 100,000 square-foot
headquarters in St. George, Utah. Wilson Electronics has product dealers in all 50 states as
well as in countries around the world.
11
12
Contact Wilson Electronics Customer Support Team with any questions at
866-839-9361 or email: [email protected]
ENGLISH
Note: For a complete list of antennas and cables approved for use with these boosters see pages 13 & 14.
Warnings and Recommendations
WARNING: To uphold compliance with network protection standards, all active cellular
devices must maintain at least 6 feet of separation distance from Panel and Dome
antennas.
WARNING: Connecting the Signal Booster directly to the cell phone with use of an adapter will
damage the cell phone.
WARNING: Use only the power supply provided in this package. Use of a non-Wilson
Electronics product may damage your equipment.
WARNING: The Signal Booster unit is designed for use in an indoor, temperature-controlled
environment (less than 150 degrees Fahrenheit). It is not intended for use in attics
or similar locations subject to temperatures in excess of that range.
WARNING: Warning: The Outside Antenna must be installed no higher than 10 meters (31’9”)
above ground.
WARNING: Take care to ensure that neither you nor the pole comes near any power lines
during installation.
RF SAFETY WARNING: Any antenna used with this device must be located at least
8 inches from all persons.
This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation. Changes or modifications not expressly approved by Wilson Electronics could void the authority to
operate this equipment.
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have
your provider’s consent. Most wireless providers consent to the use of signal boosters.
Some providers may not consent to the use of this device on their network. If you are
unsure, contact your provider.
In Canada, BEFORE USE you must meet all requirements set out in ISED CPC-2-1-05.
You MUST operate this device with approved antennas and cables as specified by the
manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from (i.e., MUST NOT
be installed within 20 cm of) any person.
You MUST cease operating this device immediately if requested by the FCC (or ISED in
Canada) or licensed wireless service provider.
WARNING. E911 location information may not be provided or may be inaccurate for calls
served by using this device.
This device may be operated ONLY in a fixed location (i.e..may operate in a fixed location
only) for in-building use.
13
14
Contact Wilson Electronics Customer Support Team with any questions at
866-839-9361 or email: [email protected]
ENGLISH
Inside Antenna Expansion Kit
(contact Wilson Technical Support for assistance)
Kit 309900-50N
2 - Wall Panel antennas
1 - 50 ohm 3-Way Splitter
Kit 309905-50N
3 - Wall Panel Antennas
3 - 2-Way 50 Ohm Splitters
Kit 309902-75F
2 - Wall Panel Antennas
1 - 3-Way 75Ohm Splitter
Kit 309903-75F
3 - Wall Panel Antennas
3 - 2-Way 75Ohm Splitters
Kit 309904-75F
1 - Wall Panel Antenna
1 - 2-Way 75 Ohm Splitter
Inside Antenna Kits
(contact Wilson Technical Support for assistance)
Kit 311155-0630
75 Ohm Wall Mount Panel Antenna
30’ RG6
Kit 311135-5820
50 Ohm Wall mount Panel Antenna
20’ RG58 Cable
Kit 311135-40060
50 Ohm Wall Mount Panel Antenna
60’ LMR400 Cable
Kit 311155-1150
75 Ohm Wall mount Panel Antenna
50’ RG11 Cable
Kit 304412-40010
50 Ohm 4G Dome Antenna
10' Wilson400 cable
Kit 304412-5810
50 Ohm 4G Dome Antenna
10' RG58 cable
Kit 304419-1110
75 Ohm 4G Dome Antenna
10' RG 11 cable
Kit 304419-17410
75 Ohm 4G Dome Antenna
10' RG174 cable
*May need separate adapter
Kit 304419-0610
75 Ohm 4G Dome Antenna
10' RG6 cable
Kit 301213
Desktop Antenna w/ 5' RG174
50 Ohm Outside Antenna Kits
(contact Wilson Technical Support for assistance)
Kit 314453-5825
50 Ohm Pole Mount Panel Antenna
25’ RG58 Cable
Kit 314411-5825
50 Ohm Wide Band Directional
25’ RG58 Cable
Kit 301111-5850
Yagi Directional Antenna
50’ RG58 Cable
Kit 311203-5820
Omni-Directional antenna
20’ RG58 Cable
Kit 311203-40020
Omni-Directional antenna
20’ LMR400 Cable
Kit 301111-400170
Yagi Directional w/ N-Female
170’ LMR400
Kit 314411-40075
50 Ohm Wide Band Directional Antenna
75’ LMR400 Cable
Kit 314453-40075
50 Ohm Pole Mount Panel Antenna
75’ LMR400 Cable
Kit 304422-40020
50 Ohm 4G Omni Antenna
20' Wilson400 cable
Kit 304422-5810
50 Ohm 4G Omni Antenna
10' RG58 cable
Kit 304422-1120
50 Ohm 4G Omni Antenna
20' RG11 cable
*May need separate adapter
75 Ohm Outside Antenna Kits
(contact Wilson Technical Support for assistance)
Kit 301111-0675
Yagi Directional Antenna
75’ RG6 Cable
N-Male to F-Female adapter
Kit 311201-0620
Omni Directional w/ F-Female
20’ RG6 Cable
13
14
Contact Wilson Electronics Customer Support Team with any questions at
866-839-9361 or email: [email protected]
ENGLISH
Kit 311141-0620
75 Ohm Grey Brick Antenna
20’ RG6 Cable
Kit 301111-11140
Yagi Directional Antenna
140’ RG11 Cable
N-Male to F-Female adapter
Kit 311201-1120
Omni Directional w/ F-Female
20’ RG11 Cable
Kit 314473-1175
75 Ohm Pole Mount Panel Antenna
75’ RG11 Cable
Kit 314475-1175
75 Ohm Wide Band Directional
75’ RG11 Cable
Kit 311141-1120
75 Ohm Grey Brick Antenna
20’ RG11 Cable
Kit 304421-1120
75 Ohm 4G Omni Antenna
20' RG 11 cable
Kit 304421-17410
75 Ohm 4G Omni Antenna
10' RG174 cable
Kit 304421-0610
75 Ohm 4G Omni Antenna
10' RG6 cable
Kit 304421-5810
75 Ohm 4G Omni Antenna
10' RG58 cable
*May need separate adapter
Mini-Mag Outside Antenna
(contact Wilson Technical Support for assistance)
301126 w/12.5 RG174 cable-SMA
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason
the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of
purchase.
3-Year Warranty
Wilson Electronics Signal Boosters are warranted for three (3) years against defects in workmanship and/or materials.
Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase.
Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of
purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics. Wilson Electronics
shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the repaired or replaced
product back to the original consumer if located within the continental U.S.
This warranty does not apply to any Signal Booster determined by Wilson Electronics to have been subjected to
misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.
Replacement products may include refurbished Wilson Electronics products that have been recertified to conform with
product specifications.
Failure to use a surge protected AC Power Strip with at least a 1000 Joule rating will void your warranty.
RMA numbers may be obtained by contacting Customer Support at 866-294-1660.
Disclaimer : The information provided by Wilson Electronics, LLC is believed to be complete and accurate.
However, no responsibility is assumed by Wilson Electronics, LLC for any business or personal losses arising from
its use, or for any infringements of patents or other rights of third parties that may result from its use.
Copyright © 2017 Wilson Electronics, LLC All rights reserved.
U.S. Patent Nos. – 7,221,967; 7,729,669; 7,486,929; 7,409,186; 7,783,318; 8,583,034; 8,583,033; 8,874,030 B2;
8,874,029 B2; 8,755,399; 8,849,187 B2; 8,639,180; D703, 181
Signal Booster Specifications
Pro 70 Plus™
Product Number 460027
Model Number 460027
FCC ID
PWO460027
IC ID
4726A-460027
Connectors F-Female
Antenna Impedance 75 Ohms
Frequency 698-716 MHz, 746-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz
Passband Gain (nominal)
700MHz Band12/17
56.0
700MHz Band13
55.2
800MHz
58.9
1700/2100MHz
60.7
1900MHz
60.7
20 dB Bandwidth (MHz)
700MHz Band12/17 700MHz Band13 800MHz 1700/2100MHz 1900MHz
Typical
Maximum
29.9
34.4
28.6
34.4
38.7
40.3
82.6
85.0
81.8
85.9
Power output for single cell
phone (Uplink) dBm
700MHz Band12/17 700MHz Band13 800MHz 1700MHz 1900MHz
20.4 20.82 25.16 23.0 21.42
Power output for single cell
phone (Downlink) dBm
700MHz Band12/17 700MHz Band13 800MHz 2100MHz 1900MHz
11.57 10.41 9.4 11.3 9.47
Power output for multiple
received channels (Uplink) dBm
No. Tones
700MHz Band12/17 700MHz Band13 800MHz 1700MHz 1900MHz
2 18.0 17.6 24.9 20.0 18.6
3 14.5 14.0 21.4 16.4 15.1
4 12.0 11.5 18.9 13.9 12.6
5 10.0 9.6 16.9 12.0 10.7
6 8.4 8.0 15.3 10.4 9.1
Power output for multiple
received channels
(Downlinklink) dBm
No. Tones 700MHz Band12/17 700MHz Band13 800MHz 2100MHz 1900MHz
2 9.50 7.60 10.00 11.70 9.10
3 6.00 4.10 6.50 8.20 5.60
4 3.50 1.60 4.00 5.70 3.10
5 1.60 -0.40 2.00 3.80 1.10
6 0.00 -1.90 0.40 2.20 -0.40
Noise Figure 5 dB nominal
Isolation > 90 dB
Power Requirements
110-240 V AC, 50-60 Hz, 20 W
Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory
reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of
authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is
too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power off on that band. For a
detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1 minute. After 5 (five) such automatic restarts,
any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing power from the Signal
Booster. Noise power, gain, and linearity are maintained by the Signal Booster’s microprocessor.
111601_Rev06_09.06.17
3301 East Deseret Drive, St. George, UT
www.wilsonelectronics.com
|
tech@wilsonelectronics.com
Copyright © 2016 Wilson Electronics. All rights reserved.
Wilson Electronics products covered by U.S. patent(s) and pending application(s)
For patents go to: weboost.com/us/patents
FRANÇAIS
Table des matières :
Fonctionnement des amplificateurs de signal cellulaire ............................. 1
Aperçu de l’installation ......................................................1
Trousse en option .......................................................... 2
Schéma d’installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 et 4
Installation de l’antenne extérieure .............................................5
Installation des antennes intérieures ...........................................7
Installation de l’amplificateur de signal .......................................... 7
Capter le meilleur signal ..................................................... 8
Réglage après l’installation/écran ACL ..........................................9
Mises en garde et recommandations .......................................... 12
Garantie ................................................................14
Spécifications ................................................Couverture arrière
Remarque : Le présent manuel contient des renseignements importants sur la sécurité et l’utilisation de cet
appareil. Veuillez lire et suivre les instructions indiquées dans le présent manuel. Le non-respect de cette
recommandation pourrait endommager votre amplificateur de signal.
L’aspect du produit et des accessoires peut varier.
GUIDE D’INSTALLATION
Amplificateur de signal cellulaire
SmarTech
®
pour bâtiment
PRO 70 PLUS
™
PRO SERIES
1
2
Pour toute question, communiquez avec le service à la clientèle de Wilson Electronics au
866-839-9361, ou par courriel à : [email protected]
FRANÇAIS
1. Déterminez l’emplacement de l’antenne extérieure sur le toit ou à l’extérieur du bâtiment.
Reportez-vous aux pages 3 à 5.
2. Pour installer votre amplificateur de signal, choisissez un endroit situé à bonne distance de toute
chaleur excessive, à l’abri des rayons du soleil et de l’humidité, et bien ventilé. L’installation de
l’amplificateur de signal dans une enceinte hermétique n’est pas recommandée. L’amplificateur
de signal doit être le plus près possible de l’antenne extérieure afin de minimiser les pertes qui
augmentent proportionnellement avec la longueur du câble.
Aperçu de l’installation
Reportez-vous au schéma d’installation des pages 3 et 4. Pour toute question, communiquez avec
le service d’assistance technique de Wilson Electronics au 866-839-9361.
Comment un amplificateur de signal cellulaire rehausse-t-il
la qualité du signal à l’intérieur d’un bâtiment
Les amplificateurs de signal cellulaire Wilson fonctionnent comme suit : une antenne extérieure
placée
sur un bâtiment où il y a faible présence de signaux cellulaires (antenne idéalement installée sur le toit ou
sur un poteau), reçoit ces signaux faibles et les transmet par un câble coaxial (similaire à celui utilisé pour
la télévision par satellite) vers un amplificateur de signal installé à l’intérieur du bâtiment. Ce signal faible
est amplifié par l’amplificateur de signal, puis transmis par câble coaxial vers des antennes intérieures qui
retransmettent le signal amplifié vers une ou plusieurs zones où le signal doit être amélioré. Les signaux
transmis par les téléphones cellulaires à l’intérieur sont captés par les antennes intérieures, amplifiés par
l’amplificateur de signal, puis transmis vers les stations cellulaires par l’antenne extérieure. Les signaux
ainsi améliorés permettent aux utilisateurs à l’intérieur du bâtiment de profiter de connexions cellulaires
stables et fiables.
À propos du gain et des zones de couverture améliorée
Plus la force du signal capté par l’antenne extérieure est faible et/ou plus la couverture nécessaire est
importante, plus le gain requis sera élevé. À l’opposé, plus la force du signal extérieur est forte, plus
la couverture cellulaire à l’intérieur du bâtiment sera grande. L’orientation appropriée de l’antenne vers
la source du signal cellulaire est également importante. Le gain obtenu par les antennes extérieure et
intérieure, et affaibli par les pertes sur toute la longueur du câble coaxial, a également une incidence
sur l’efficacité de la couverture. Étant donné que les antennes offrent un fonctionnement directionnel,
l’emplacement de l'antenne intérieure est également important. Les matériaux constituant les murs
ont également une incidence sur la force du signal.
Une isolation inadéquate entre l’antenne extérieure et les antennes intérieures est également un élément
qui peut avoir des incidences sur la force du signal. Les amplificateurs de signal Wilson ont été conçus
pour diminuer leur gain interne afin d’éviter tout retour d’oscillations de fréquence qui, si elles sont non
contrôlées, peuvent compromettre le bon fonctionnement de stations cellulaires à proximité. L’écran
ACL de l'amplificateur de signal indique si l’amplificateur fournit un gain optimal sur chaque bande de
fréquence cellulaire. Un gain optimal peut être obtenu en augmentant la distance entre les antennes
(isolation) jusqu’à ce que le gain obtenu soit maximal. Si la distance entre les antennes est limitée par la
configuration du bâtiment, le gain ne pourra être optimisé. Une station cellulaire à proximité, même si elle
ne transmet aucun signal à des utilisateurs, peut également forcer le circuit de protection automatique
de réseau de l'amplificateur de signal à réduire le gain ou même à couper une ou plusieurs bandes de
fréquence de l'amplificateur de signal pour éviter toute surcharge de signaux vers la station. L'écran de
l’amplificateur de signal peut également servir à déterminer si cette situation survient. Reportez-vous
aux pages 9 à 11 pour en savoir plus sur l’écran d'état de l’amplificateur de signal.
1
2
Pour toute question, communiquez avec le service à la clientèle de Wilson Electronics au
866-839-9361, ou par courriel à : [email protected]
FRANÇAIS
Pro 70 Plus Câble RG11
de 2 pi
Limiteur de surtension
due à la foudre
Antenne directionnelle
à large bande
avec câble RG11 de 75 pi
Antenne à panneau
à large bande avec câble
RG11 de 50 pi
460127 Trousse
460227 Trousse
Pro 70 Plus Bloc d’alimentation
c.a./c.c.
12 V/3 A
Bloc d’alimentation
c.a./c.c.
12 V/3 A
Câble RG11
de 2 pi
Limiteur de surtension
due à la foudre
Antenne directionnelle
à large bande
avec câble RG11 de 75 pi
Antenne dôme 4G
pour plafond
Câble RG11 de 50 pi
3. Branchez le câble de l'antenne extérieure au connecteur de l’amplificateur de signal portant la
mention « Antenne extérieure ». Reportez-vous à la page 6 pour obtenir plus de renseignements
sur l’acheminement du câble. Un limiteur de surtension due à la foudre est recommandé pour les
installations en bâtiment. Reportez-vous aux pages 3 à 6.
4. Choisissez un endroit pour installer l'antenne intérieure. Tentez de choisir un emplacement
central dans la zone où la force du signal doit être améliorée. Souvenez-vous que la distance
entre l’antenne intérieure et l’antenne extérieure (isolation) est importante pour assurer le bon
fonctionnement du système. Il peut être nécessaire de prévoir une distance de séparation variant
de 50 à 75 pieds entre l’antenne intérieure et l’antenne extérieure. La séparation verticale améliore
également l’isolation entre les antennes. D’autres méthodes d’isolation peuvent être adoptées.
S’il est impossible de séparer physiquement les antennes, veuillez communiquer avec le service
d’assistance technique de Wilson Electronics au 866-839-9361 pour en savoir plus sur des
méthodes d’isolation supplémentaires.
5. Branchez le câble de l'antenne intérieure au connecteur de l’amplificateur de signal portant la
mention « Antenne intérieure ». Reportez-vous à la page 6 pour obtenir plus de renseignements
sur l’acheminement du câble. Assurez-vous d’utiliser la plus courte longueur de câble possible pour
éviter toute perte de signal.
6. Avant de mettre sous tension l’amplificateur de signal, assurez-vous que l’antenne extérieure et
l’antenne intérieure sont branchées et que tous les branchements sont solides. Remarque : Usez
de prudence au moment de brancher le connecteur pour éviter de déformer les broches centrales
des connecteurs.
7. Mettez l’amplificateur de signal sous tension en utilisant le bloc d’alimentation fourni. Si les témoins
ne sont pas de couleur verte, reportez-vous aux pages 9 à 11.
Trousses multiples offertes en option
Remarque : Les trousses peuvent comprendre différents accessoires.
Pour acheter des trousses supplémentaires, communiquez avec le service des ventes de Wilson
Electronics au : 888-503-5329
3
4
Pour toute question, communiquez avec le service à la clientèle de Wilson Electronics au
866-839-9361, ou par courriel à : [email protected]
FRANÇAIS
Schéma d’installation
Distance importante
Antenne intérieure
Bloc d’alimentation
Antenne intérieure
Méthode privilégiée : Placez
l’antenne intérieure au plafond et
orientée vers le sol pour profiter
d’une couverture optimale.
Remarque : Un limiteur de surtension due
à la foudre Wilson (589902) est recommandé pour
les installations en bâtiment. Assurez-vous que
le limiteur de surtension est installé à l’extérieur
du bâtiment à un point d’accès raccordé à une
mise à la terre appropriée et en ligne entre
l’antenne extérieure et l’amplificateur de signal.
Limiteur de surtension
Barre d’alimentation
Antenne extérieure
(antenne directionnelle
à large bande illustrée)
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

WilsonPro Pro 70 Plus (75Ω) Guide d'installation

Marque
WilsonPro
Modèle
Pro 70 Plus (75Ω)
Catégorie
Amplificateurs de signal cellulaire
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents