Jenn-Air Range DUAL-FUEL PRO-STYLETM SLIDE-IN RANGE Manuel utilisateur

Taper
Manuel utilisateur
JENN-AIR
®
DUAL-FUEL PRO-STYLE
TM
SLIDE-IN RANGE
Form No. A/05/06 Part No. 8113P640-60 ©2006 Maytag Appliances Sales Co. All rights reserved. Litho U.S.A .
Important Safety Instructions .....................................1-4
Care & Cleaning ..............................................................5-7
Maintenance.....................................................................8-9
Troubleshooting ......................................................... 10-11
Surface Cooking......................................................... 12-13
Oven Cooking..............................................................14-20
Options .......................................................................... 21-25
Favorites ...............................................................................26
Setup .............................................................................. 27-29
Accessories .........................................................................30
Warranty & Service...........................................................31
Guide d’utilisation et d’entretien .................................32
Guía de uso y cuidado ....................................................64
USE & CARE
GUIDE
TABLE OF CONTENTS
®
1
Installer: Please leave this guide with this appliance.
Consumer: Please read and keep this guide for future
reference. Keep sales receipt and/or cancelled check as
proof of purchase.
Model Number __________________________________
Serial Number __________________________________
Date of Purchase ________________________________
If you have questions, call:
Jenn-Air Customer Assistance
1-800-JENNAIR (1-800-536-6247)
1-800-688-2080 (U.S. TTY for hearing or speech impaired)
(Mon.-Fri., 8 am-8 pm Eastern Time)
Internet: http://www.jennair.com
In our continuing effort to improve the quality and
performance of our cooking products, it may be necessary
to make changes to the appliance without revising this
guide.
For service information, see page 31.
IMPORTANT SAFETY
INSTRUCTIONS
Warning and Important Safety Instructions appearing in
this guide are not meant to cover all possible conditions
and situations that may occur. Common sense, caution,
and care must be exercised when installing,
maintaining, or operating the appliance.
Always contact the manufacturer about problems or
conditions you do not understand.
Recognize Safety Symbols, Words, Labels
WARNING – Hazards or unsafe practices which
COULD result in severe personal injury or death.
CAUTION – Hazards or unsafe practices which
COULD result in minor personal injury.
WARNING
CAUTION
Read and follow all instructions before using this
appliance to prevent the potential risk of fire, electric
shock, personal injury or damage to the appliance as a
result of improper usage of the appliance. Use appliance
only for its intended purpose as described in this guide.
To ensure proper and safe operation: Appliance
must be properly installed and grounded by a qualified
General Instructions
WARNING: To reduce risk of
tipping of the appliance from
abnormal usage or by excessive loading of the
oven door, the appliance must be secured by a
properly installed anti-tip device.
WARNING
ALL RANGES CAN TIP AND
CAUSE INJURIES TO PERSONS
INSTALL ANTI-TIP DEVICE
PACKED WITH RANGE
FOLLOW ALL INSTALLATION
INSTRUCTIONS
technician. Do not attempt to adjust, repair, service,
or replace any part of your appliance unless it is
specifically recommended in this guide. All other
servicing should be referred to a qualified servicer.
Always disconnect power to appliance before servicing.
If the information in this guide is not followed
exactly, a fire or explosion may result causing
property damage, personal injury or death.
Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any appliance.
IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch.
Do not use any phone in your building.
Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
WARNING
Gas leaks may occur in your system and result in a
dangerous situation. Gas leaks may not be detected
by smell alone. Gas suppliers recommend you
purchase and install an UL approved gas detector.
Install and use in accordance with the manufacturer’s
instructions.
WARNING
To check if device is properly installed, look underneath
range with a flashlight to make sure one of the rear
2
leveling legs is properly engaged in the bracket slot. The
anti-tip device secures the rear leveling leg to the floor
when properly engaged. You should check this anytime
the range has been moved.
To Prevent Fire or Smoke
Damage
Be sure all packing materials are removed from the
appliance before operating it.
Keep area around appliance clear and free from
combustible materials. Flammable materials should not
be stored in an oven.
Many plastics are vulnerable to heat. Keep plastics away
from parts of the appliance that may become warm or
hot. Do not leave plastic items on the cooktop as they
may melt or soften if left too close to the vent or a
lighted surface burner.
T3lefp af lef/43Bicur,t. Do n ot
3
IMPORTANT SAFETY INSTRUCTIONS
To prevent potential hazard to the user and damage to
the appliance, do not use appliance as a space heater
to heat or warm a room. Also, do not use the oven as a
storage area for food or cooking utensils.
NEVER use aluminum foil to cover an oven rack or oven
bottom. Misuse could result in risk of electric shock, fire,
or damage to the appliance. Use foil only as directed in
this guide.
Cooking Safety
Always place a pan on a surface burner before turning it
on. Be sure you know which knob controls which
surface burner. Make sure the correct burner is turned
on and that the burner has ignited. When cooking is
completed, turn burner off before removing pan to
prevent exposure to burner flame.
Always adjust surface burner flame so that it does not
extend beyond the bottom edge of the pan. An exces-
sive flame is hazardous, wastes energy and may damage
the appliance, pan or cabinets above the appliance.
NEVER leave a surface cooking operation unattended,
especially when using a high heat setting or when deep
fat frying. Boilovers cause smoking and greasy spillovers
may ignite. Clean up greasy spills as soon as possible.
Do not use high heat for extended cooking operations.
NEVER heat an unopened container on the surface
burner or in the oven. Pressure build-up may cause
container to burst resulting in serious personal injury or
damage to the appliance.
Use dry, sturdy potholders. Damp potholders may cause
burns from steam. Dish towels or other substitutes
should never be used as potholders because they can
trail across hot surface burners and ignite or get caught
on appliance parts.
Always let quantities of hot fat used for deep fat frying
cool before attempting to move or handle.
Do not let cooking grease or other flammable materials
accumulate in or near the appliance, hood or vent fan.
Clean hood frequently to prevent grease from
accumulating on hood or filter. When flaming foods
under the hood turn the fan on.
NEVER wear garments made of flammable material or
loose fitting or long-sleeved apparel while cooking.
Clothing may ignite or catch utensil handles.
Utensil Safety
Use pans with flat bottoms and handles that are easily
grasped and stay cool. Avoid using unstable, warped,
easily tipped or loose-handled pans. Also avoid using
pans, especially small pans, with heavy handles as they
could be unstable and easily tip. Pans that are heavy to
move when filled with food may also be hazardous.
Be sure utensil is large enough to properly contain food
and avoid boilovers. Pan size is particularly important in
deep fat frying. Be sure pan will accommodate the
volume of food that is to be added as well as the bubble
action of fat.
Always place oven racks in the desired positions while
oven is cool. Slide oven rack out to add or remove food,
using dry, sturdy potholders. Always avoid reaching into
the oven to add or remove food. If a rack must be
moved while hot, use a dry potholder. Always turn the
oven off at the end of cooking.
Use care when opening the oven door. Let hot air or
steam escape before moving or replacing food.
PREPARED FOOD WARNING: Follow food
manufacturer’s instructions. If a plastic frozen food
container and/or its cover distorts, warps, or is otherwise
damaged during cooking, immediately discard the food
and its container. The food could be contaminated.
NEVER use aluminum foil to cover oven racks or oven
bottom. This could result in risk of electric shock, fire, or
damage to the appliance. Use foil only as directed in this
guide.
Heating Elements
NEVER touch surface or oven heating elements, areas near
elements, or interior surfaces of ovens.
Heating elements may be hot even though they are dark in
color. Areas near surface elements and interior surfaces of
the ovens may become hot enough to cause burns. During
and after use, do not touch or let clothing or other
flammable materials contact heating elements, areas near
elements, or interior surfaces of ovens until they have had
sufficient time to cool.
Other potentially hot surfaces include: Cooktop, areas
facing the cooktop, oven vent, and surfaces near the vent
opening, oven doors, areas around the doors and oven
windows.
Do not touch a hot oven light bulb with a damp cloth as
the bulb could break. Should the bulb break, disconnect
power to the appliance before removing bulb to avoid
electrical shock.
CAUTION
Do not clean door gasket. The door gasket is essential
for a good seal. Care should be taken not to rub,
damage, or move the gasket.
Do not use oven cleaners or oven liners of any kind in or
around any part of the self-clean oven.
Important Safety Notice
and Warning
The California Safe Drinking Water and Toxic
Enforcement Act of 1986 (Proposition 65) requires the
Governor of California to publish a list of substances
known to the State of California to cause cancer or
reproductive harm, and requires businesses to warn
customers of potential exposures to such substances.
Users of this appliance are hereby warned that when
the oven is engaged in the self-clean cycle, there may
be some low-level exposure to some of the listed
substances, including carbon monoxide. Exposure to
these substances can be minimized by properly venting
the oven to the outdoors by opening the windows and/
or door in the room where the appliance is located
during the self-clean cycle.
IMPORTANT NOTICE REGARDING PET BIRDS:
Never keep pet birds in the kitchen or in rooms where
the fumes from the kitchen could reach. Birds have a
very sensitive respiratory system. Fumes released during
an oven self-cleaning cycle may be harmful or fatal to
birds. Fumes released due to overheated cooking oil, fat,
margarine and overheated non-stick cookware may be
equally harmful.
To minimize burns, ignition of flammable materials and
spillage due to unintentional contact with the utensil, do
not extend handles over adjacent surface burners.
Always turn pan handles toward the side or back of the
appliance, not out into the room where they are easily
hit or reached by small children.
Never let a pan boil dry as this could damage the
utensil and the appliance.
Follow the manufacturer’s directions when using oven
cooking bags.
Only certain types of glass, glass/ceramic, ceramic or
glazed utensils are suitable for cooktop or oven usage
without breaking due to the sudden change in
temperature. Follow manufacturer’s instructions when
using glass.
This appliance has been tested for safe performance
using conventional cookware. Do not use any devices
or accessories that are not specifically recommended in
this guide. Do not use element covers for the surface
units, stovetop grills, or add-on oven convection
systems. The use of devices or accessories that are not
expressly recommended in this guide can create serious
safety hazards, result in performance problems, and
reduce the life of the components of the appliance.
Deep Fat Fryers
Use extreme caution when moving the grease pan or
disposing of hot grease. Allow grease to cool before
attempting to move pan.
Ventilating Hoods
Clean range hood and filters frequently to prevent
grease or other flammable materials from accumulating
on hood or filter and to avoid grease fires.
When flaming foods under the hood, turn the fan on.
Cleaning Safety
Clean cooktop with caution. Turn off all controls and
wait for appliance parts to cool before touching or
cleaning. Use care to avoid steam burns if a wet sponge
Save These Instructions for Future Reference
4
Before self-cleaning the oven, remove the oven racks,
broiler pan, food and any other utensils. Wipe
spillovers to prevent excessive smoke and flare-ups.
or cloth is used to wipe spills on a hot surface. Some
cleaners can produce noxious fumes if applied to a hot
surface.
Clean only parts listed in this guide.
Self-Clean Oven
5
CARE & CLEANING
* Brand names for cleaning products are registered trademarks of the respective manufacturers.
Self-Clean Oven
CAUTION
It is normal for parts of the oven to become hot during a
self-clean cycle.
To prevent damage to oven door, do not attempt to open
the door when LOCK is displayed.
Avoid touching door, window or oven vent area during a
clean cycle.
Do not use commercial oven cleaners on the oven finish
or around any part of the oven. They will damage the
finish or parts.
The self-clean cycle uses above-normal cooking temperatures
to automatically clean the oven interior.
The oven should be cleaned regularly by wiping up spillovers
to prevent excessive smoke and flare-ups. Do not allow a
heavy build-up of soil to accumulate in the oven.
During the cleaning process, the kitchen should be well
ventilated to get rid of normal odors associated with cleaning.
Before Self-Cleaning
1. Turn off the oven light before cleaning. The oven light may
burn out during the clean cycle.
2. Remove broiler pan, all pans, and oven racks from the
oven. The oven racks will discolor and may not slide easily
after a self-clean cycle if they are not removed.
3. Clean oven frame, door frame, area
outside of gasket, and around the
opening in the door gasket with a
nonabrasive cleaner such as Bon
Ami* or detergent and water. The
self-cleaning process does not
clean these areas. They should be
cleaned to prevent soil from baking
on during the clean cycle. (The gasket is the seal around
the oven door and window.)
4. To prevent damage, do not clean or rub the gasket around
the oven door. The gasket is designed to seal in heat
during the clean cycle.
5. Wipe up excess grease or spill-overs from the oven
bottom. This prevents excessive smoking, flare-ups or
flaming during the clean cycle.
6. Wipe up sugary and acidic spillovers such as sweet
potatoes, tomato, or milk-based sauces. Porcelain enamel
is acid-resistant, not acid-proof. The porcelain finish may
discolor if acidic or sugary spills are not wiped up before a
self-clean cycle.
To set Self-Clean:
1. Press Clean pad.
2. REMOVE RACKS will be displayed. Remove the racks.
3. Select CONTINUE using the Quickset pad. The Quickset
pads are located on either side of the control panel dsplay.
4. Set LIGHT soil level by entering 200 using the number
pads for two hours of cleaning time. Press the Enter pad.
OR
Select MEDIUM for a moderately soiled oven and three
hours of cleaning time.
To Delay a Self-Clean Cycle:
1. Press Clean pad.
2. REMOVE RACKS will be displayed.
Remove the racks.
3. Select CONTINUE using the Quickset pad..
4. Set LIGHT soil level by entering 200 using the number
pads for two hours of cleaning time. Press the Enter pad.
OR
Select MEDIUM for a moderately soiled oven and three
hours of cleaning time.
OR
Select HEAVY for a heavily soiled oven and four hours of
cleaning time.
5. The door will lock. CLEAN, TIME, LOCKED and the
cleaning time countdown will be displayed
6. After door locks, press the More Options pad.
7. Select DELAY using the Quickset pad..
8. Select the number of hours you want to delay the start of the
self-clean cycle.
9. The delay time and cleaning time will be displayed.
OR
Select HEAVY for a heavily soiled oven and four hours of
cleaning time.
5. CLEAN, TIME, LOCKED and the cleaning time countdown
will be displayed while the oven is cleaning. OVEN
COOLING will appear in the display when the cleaning
time has been completed and the oven is still locked.
Important: The door lock will disengage approximately one
hour after the cleaning time is completed. OVEN COOLING
will go off in the display when the oven door has unlocked.
6
Notes:
If the oven door is left open, CLOSE DOOR will appear in
the display until the door is closed.
If more than 30 seconds elapse between pressing the
Clean pad and pressing a number pad, the program will
automatically return to the previous display.
The oven door will be damaged if it is forced to open
during cleaning or cooling process.
The first few times the oven is cleaned, some smoke and
odor may be detected. This is normal and will lessen or
disappear with use. If the oven is heavily soiled, or if the
broiler pan was accidently left in the oven, excessive
smoke and odor may occur.
As the oven heats and cools, you may hear sounds of
metal parts expanding and contracting. This is normal
and will not damage your appliance.
After Self-Cleaning
About one hour after the end of the clean cycle, the lock
will disengage and OVEN COOLING will go off in the
display. At this point, the door can be opened.
Some soil may leave a light gray, powdery ash which can be
removed with a damp cloth. If soil remains, it indicates that
the clean cycle was not long enough. The soil will be removed
during the next clean cycle.
If the oven racks were left in the oven and do not slide
smoothly after a clean cycle, wipe racks and embossed rack
supports with a small amount of vegetable oil to restore ease
of movement.
A white discoloration may appear after cleaning if acidic or
sugary foods were not wiped up before the clean cycle. This is
normal and will NOT affect performance.
PART PROCEDURE
CAUTION
Cleaning Procedures
Be sure appliance is off and all parts are cool before handling
or cleaning. This is to avoid damage and possible burns.
To prevent staining or discoloration, clean appliance after each use.
If a part is removed, be sure it is correctly replaced.
* Brand names are registered trademarks of the
respective manufacturers.
** To order call 1-800-JENNAIR (1-800-536-6247).
Broiler Pan Never cover insert with aluminum foil as this prevents the fat from draining to the pan below.
Accessory Place soapy cloth over insert and pan; let soak to loosen soil.
and Insert Wash in warm, soapy water. Use scouring pad to remove stubborn soil.
Broiler pan and insert can be cleaned in dishwasher.
Burner Caps and Removable Burner Caps
Sealed Gas Allow burner to cool. Remove burner cap and wash in soapy water with a plastic scouring pad. For
Burners stubborn soils, clean with a soap-filled, nonabrasive pad or Cooktop Cleaning Creme*
(Part #20000001)** and a sponge.
Do not clean in the dishwasher or self-cleaning oven.
Sealed Gas Burners
Clean frequently. Allow burner to cool. Clean with soap and plastic scouring pad. For stubborn or
dried-on soils, clean with a soap-filled, nonabrasive pad, stiff brush, toothbrush, the soft rubber tip on
the toothbrush (if equipped) or a straight pin. Do not enlarge or distort holes.
Be careful not to get water into burner ports.
Use care when cleaning the ignitor. If the ignitor is wet or damaged the surface burner will not light.
Burner Grates - Wash with warm, soapy water and a nonabrasive, plastic scrubbing pad. For stubborn soils,
Porcelain on clean with a soap-filled, nonabrasive, plastic pad or Cooktop Cleaning Creme* and a sponge. If soil
Cast Iron remains, reapply Cooktop Cleaning Creme, cover with a damp paper towel and soak for 30 minutes.
Scrub again, rinse and dry.
Do not clean in the dishwasher or self-cleaning oven.
Clock and To activate control lock for cleaning, see Locking the Control, page 15.
Control Pad Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish.
Area Glass cleaners may be used if sprayed on a cloth first. DO NOT spray directly on control pad and
display area.
Cont.
7
* Brand names for cleaning products are registered trademarks of the respective manufacturers.
** To order direct, call 1-800-JENNAIR (1-800-536-6247).
PART PROCEDURE
Control Knobs Remove knobs in the OFF position by pulling forward.
Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish.
Turn on each burner to be sure the knobs have been correctly replaced.
Cooktop and Porcelain enamel is glass fused on metal and may crack or chip with misuse. It is acid-resistant, not acid-
Control Panel - proof. All spillovers, especially acidic or sugary spillovers, should be wiped up immediately with a dry cloth.
Porcelain When cool, wash with soapy water, rinse and dry.
Enamel Never wipe off a warm or hot surface with a damp cloth. This may cause cracking or chipping.
Never use oven cleaners, abrasive or caustic cleaning agents on exterior finish of range.
Side Panels, When cool, wash with warm, soapy water, rinse and dry. Never wipe a warm or hot surface with a damp
Warming cloth as this may damage the surface and may cause a steam burn.
Drawer and For stubborn soil, use mildly abrasive cleaning agents such as baking soda paste or Bon Ami*. Do not use
Door Handles - abrasive cleaners such as steel wool pads or oven cleaners. These products will scratch or permanently
Painted Enamel damage the surface.
Note: Use a dry towel or cloth to wipe up spills, especially acidic or sugary spills. Surface may
discolor or dull if soil is not immediately removed. This is especially important for white surfaces.
Oven Window Avoid using excessive amounts of water which may seep under or behind glass causing staining.
and Door - Glass Wash with soap and water. Rinse with clear water and dry. Glass cleaner can be used if sprayed on a cloth
first.
Do not use abrasive materials such as scouring pads, steel wool or powdered cleaners as they will scratch
glass.
Oven Interior Follow instructions on page 5-6 to set a self-clean cycle.
Oven Racks Clean with soapy water.
Remove stubborn soil with cleansing powder or soap-filled scouring pad. Rinse and dry.
Racks will permanently discolor and may not slide out smoothly if left in the oven during a self-clean
operation. If this occurs, wipe the rack and embossed rack supports with a small amount of vegetable oil
to restore ease of movement, then wipe off excess oil.
Stainless Steel DO NOT USE ANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH.
(select models) DO NOT USE ABRASIVE OR ORANGE CLEANERS.
ALWAYS WIPE WITH THE GRAIN WHEN CLEANING.
Daily Cleaning/Light Soil –– Wipe with one of the following - soapy water, white vinegar/water solution,
Formula 409 Glass and Surface Cleaner* or a similar glass cleaner - using a sponge or soft cloth.
Rinse and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray*
(Part No. 20000008)**.
Moderate/Heavy Soil –– Wipe with one of the following - Bon Ami, Smart Cleanser, or Soft Scrub* -
using a damp sponge or soft cloth. Rinse and dry. Stubborn soils may be removed with a damp Scotch-
Brite* pad; rub evenly with the grain. Rinse and dry. To restore luster and remove streaks, follow with
Stainless Steel Magic Spray*.
Discoloration –– Using a damp sponge or soft cloth, wipe with Cameo Stainless Steel Cleaner*. Rinse
immediately and dry. To remove streaks and restore luster, follow with Stainless Steel Magic Spray*.
CARE & CLEANING
8
Leveling Legs
ANTI-TIP BRACKE
T
LEVELING LEG
Be sure the anti-tip bracket secures one of the rear
leveling legs to the floor. This bracket prevents the range
from accidentally tipping.
Be sure the range is leveled when installed. If
the range is not level, turn the leveling legs,
located at each corner of the range, until range
is level.
ANTI-TIP BRACKET
LEVELING LEG
CAUTION
To assure the proper replacement bulb is used, order bulb
from Jenn-Air. Call 1-800-JENNAIR (1-800-536-6247), ask for
part number 74004458 - halogen bulb.
To Replace Oven Light Bulb:
1. Disconnect power to the wall oven.
2. When oven is cool, use fingertips to grasp edge of bulb
cover. Pull out and remove.
3. Carefully remove old bulb by pulling straight out of
ceramic base.
4. To avoid damaging or decreasing the life of the new bulb,
do not touch the bulb with bare hands or fingers. Hold
with a dry cloth or paper towel. Push new bulb prongs
straight into small holes of ceramic base.
5. Replace bulb cover by snapping into place.
6. Reconnect power to the oven. Reset clock.
Oven Light
CAUTION
Disconnect power to oven before replacing light bulb.
Allow oven to cool before replacing light bulb.
Make sure bulb cover and bulb are cool before touching.
MAINTENANCE
CAUTION
Oven Door
NEVER place excessive weight on or stand on an open
oven door. This could cause the range to tip over, break
the door, or injure the user.
NEVER attempt to open or close door or operate oven until
door is properly replaced.
NEVER place fingers between hinge and front oven frame.
Hinge arms are spring mounted. If accidentally hit, the
hinge will slam shut against oven frame and could injure
your fingers.
To remove:
1. When cool, open the oven door
to the broil stop position
(opened about four inches).
2. Grasp door at each side. Do
not use the door handle to lift
door.
3. Lift up evenly until door clears hinge arms.
To replace:
1. Grasp door at each side.
2. Align slots in the door with the hinge arms on the range.
3. Slide the door down onto the hinge arms until the door is
completely seated on the hinges. Push down on the top
corners of the door to completely seat door on hinges.
Door should not appear crooked.
Important: The oven door on a new range may feel “spongy”
when it is closed. This is normal and will decrease with use.
Oven Window
To protect the oven door window:
1. Do not use abrasive cleaning agents such as steel wool,
scouring pads or powdered cleansers as they may scratch
the glass.
2. Do not hit the glass with pots, pans, furniture, toys, or
other objects.
3. Do not close the oven door until the oven racks are in
place.
Scratching, hitting, jarring or stressing the glass may weaken
its structure causing an increased risk of breakage at a later
date.
9
Removal of Gas Appliance
Gas appliance connectors used to connect this appliance to
the gas supply are not designed for continuous movement.
Once installed, DO NOT repeatedly move this gas appliance
for cleaning or to relocate. If this appliance has to be moved
and/or removed for servicing, follow the procedure described
in the installation instructions. For information, contact Jenn-
Air Customer Service at 1-800-JENNAIR (1-800-536-6247).
To prevent range from accidentally tipping, range must be
secured to the floor by sliding rear leveling leg into the anti-
tip bracket.
MAINTENANCE
10
TROUBLESHOOTING
For most concerns, try these first. Check if oven controls have been properly set.
Check to be sure plug is securely inserted into receptacle.
Check or re-set circuit breaker. Check or replace fuse.
Check power supply.
Part or all of appliance does not Check if surface and/or oven controls have been properly set. See pgs. 12 & 16.
work. Check if oven door is unlocked after self-clean cycle. See pg. 6.
Check if oven is set for a delayed cook or clean program. See pgs. 16 & 5.
Check if control lock is activated. See pg. 15.
Check if control is in Sabbath Mode. See pg. 28.
Clock, indicator words, and/or Oven may be set for a Cook & Hold or delay function.
lights operate but oven does Control lock may have been set. (See pg. 15.)
not heat.
Surface burner fails to light. Check to be sure unit is properly connected to power supply.
Check for a blown circuit fuse or a tripped main circuit breaker.
Check to be sure ignitor is dry and clicking. Burner will not light if ignitor is damaged,
soiled or wet. If ignitor doesn’t click, turn control knob OFF.
The flame is uneven. Burner ports may be clogged.
Surface burner flame lifts Check to be sure a pan is sitting on the grate above.
off ports.
Baking results are not as Check the oven temperature selected. Make sure oven is preheated when recipe
expected or differ from or directions recommend preheat.
previous oven. Make sure the oven vent has not been blocked. See page 20 for location.
Check to make sure range is level.
Temperatures often vary between a new oven and an old one. As ovens age, the oven
temperature often “drifts” and may become hotter or cooler. See page 29 for
instructions on adjusting the oven temperature. Important: It is not recommended
to adjust the temperature if only one or two recipes are in question.
Use correct pan. Dark pans produce dark browning. Shiny pans produce light
browning.
Check rack positions and pan placement. Stagger pans when using two racks. Allow
1-2 inches between pans and oven wall.
Check the use of foil in the oven. Never use foil to cover an entire oven rack. Place
a small piece of foil on the rack below the pan to catch spillovers.
Food is not broiling properly or Check oven rack positions. Food may be too close to flame.
smokes excessively. Aluminum foil was incorrectly used. Never line the broiler insert with foil.
Trim excess fat from meat before broiling.
A soiled broiler pan was used.
Preheat oven for 2-3 minutes before placing food in the oven.
PROBLEM SOLUTION
Cont.
11
Oven will not self-clean. Check to make sure the cycle is not set for a delayed start. See pg. 5.
Check if door is closed.
Check if control is in Sabbath Mode. See pg. 28.
Oven may be over 400° F. Oven temperature must be below 400° F to program a
clean cycle.
Oven did not clean properly. Longer cleaning time may be needed.
Excessive spillovers, especially sugary and/or acidic foods, were not removed prior
to the self-clean cycle.
Oven door will not unlock after Oven interior is still hot. Allow about one hour for the oven to cool after the
self-clean cycle. completion of a self-clean cycle. The door can be opened when the LOCK indicator
word is not displayed.
The control and door may be locked. See pg. 15.
There are no beeps and Oven may be in Sabbath Mode. See page 28.
no display.
Moisture collects on oven This is normal when cooking foods high in moisture.
window or steam comes from Excessive moisture was used when cleaning the window.
oven vent.
There is a strong odor or light This is normal for a new range and will disappear after a few uses. Initiating a clean
smoke when oven is turned on. cycle will “burn off” the odors more quickly.
Turning on a ventilation fan will help remove the smoke and/or odor.
Excessive food soils on the oven bottom. Use a self-clean cycle.
Fault Codes The oven may detect a fault during programming or during operation. If a fault is
detected, the message FAULT DETECTED - DISABLE POWER TO CLEAR or FAULT
DETECTED - PRESS ENTER TO TRY AGAIN may appear. Follow directions in the display.
If the fault reappears or does not clear, call an authorized servicer or the toll-free
number in the display.
If the same operation is attempted before having the oven repaired, the message
FEATURE NOT AVAILABLE will appear. The feature will remain inoperable until service
is obtained.
If the oven is heavily soiled, excessive flareups may result in a fault code during
cleaning. Press the CANCEL pad and allow the oven to cool completely, wipe out
excess soil, then reset the clean cycle. If the fault code reappears, contact an
authorized servicer.
Noises may be heard. The oven makes several low-level noises. You may hear the oven relays as they go on
and off. This is normal.
As the oven heats and cools, you may hear sounds of metal parts expanding and
contracting. This is normal and will not damage your appliance.
SABBATH displayed Oven is in Sabbath Mode. To cancel, press and hold the Setup pad for five
continuously. seconds.
Cannot add another Favorite. Favorites is full. To delete a favorite and add another, see page 26.
PROBLEM SOLUTION
The size and type of cookware, type and amount of food and
BTU of the burner will determine where
to set the knob for cooking operations.
Use the settings printed around the
knobs as a guide. The following
descriptions will aid in choosing the
type setting that will gived optimum
results:
Hold or Warm: Food maintains a
temperature above 140° F without
continuing to cook. Food is heated on a
higher flame size until it reaches this temperature and then
the flame size is reduced. Never use a hold or warm setting to
reheat cold food. Be sure knob is adjusted to produce a stable
flame. (Use the LOW setting or the simmer burner located at
the right rear to keep food warm.)
Simmer: Food forms bubbles that barely break the surface.
Foods are between 185° F and 200° F. A simmer setting can
also be used to steam or poach foods or continue cooking
covered foods. (Adjust the knob between HIGH and LOW to
obtain the desired simmer action.)
Slow Boil: Food forms bubbles at a moderate pace. A slow
boil setting can also be used for most frying and for
maintaining the cooking of large amounts of liquids. (Adjust
the knob between HIGH and LOW to obtain the desired boil
action.)
Boil: Liquid forms bubbles at a rapid pace. A fast boil setting
can be used to bring liquid to a boil, brown meat, stir fry,
saute, and heat oil for frying before turning to a lower setting.
The HIGH setting is always used to bring liquids to a boil.
Once the liquid boils, always reduce the flame size to the
lowest setting that will maintain the boil action. (Turn the knob
to HIGH then adjust the flame size to fit the size of the pan.)
12
SURFACE COOKING
Surface Controls
Pilotless Ignition
Pilotless ignition eliminates the
need for a constant standing
pilot light. Each surface burner
has a spark ignitor. Use care
when cleaning around the surface
burner.
If the surface burner does
not light, check if ignitor is
broken, soiled or wet.
Surface Control Knobs
Use to turn on the surface burners. An infinite choice of heat
settings is available from Low to High. At the High setting a
detent or notch may be felt. The knobs can be set on or
between any of the settings.
Graphics next to the knob identify which burner
the knob controls. For example, the graphic at left
shows a front burner location.
Setting the controls:
The size and type of cookware will affect the heat setting.
1. Place a pan on the burner grate.
The burner flame may lift off or appear separated from
the port if a pan is not placed on the grate.
2. Push in and turn the knob to the desired setting.
A clicking (spark) sound will be heard and the burner
will light.
Important: Each surface burner is equipped to provide
automatic reignition if the flame should somehow get blown
out.
CAUTION
If flame should go out during a cooking operation and
the burner does not reignite itself, turn the burner off. If a
strong gas odor is detected, open a window and wait five
minutes before relighting the burner.
Be sure all surface controls are set in the OFF position
prior to supplying gas to the range.
NEVER touch cooktop until it has cooled. Expect some
parts of the cooktop, especially around the burners, to
become warm or hot during cooking. Use potholders to
protect hands.
CAUTION
When lighting the surface burners, be sure all of the
controls are in the OFF position. Strike the match first and
hold it in position before turning the knob on.
1. Hold a lighted match to the desired surface burner head.
2. Push in and turn the control knob slowly on.
3. Adjust the flame to the desired level.
Operating During a
Power Failure
Suggested Heat Settings
13
Cooktop
Notes:
A properly adjusted burner with clean ports will light
within a few seconds. If using natural gas, the flame
will be blue with a deeper blue inner cone.
If the burner flame is yellow or is noisy, the air/gas
mixture may be incorrect. Contact a service technician
to adjust. (Adjustments are not covered by the
warranty.)
With LP gas, slight yellow tips on the flames are
acceptable. This is normal and adjustment is not
necessary.
With some types of gas, you may hear a “popping”
sound when the surface burner is turned off. This is a
normal operating sound of the burner.
If the control knob is turned very quickly from High to
Low, the flame may go out, particularly if the burner is
cold. If this occurs, turn the knob to the OFF position,
wait several seconds and relight the burner.
The flame should be adjusted so it does not extend
beyond the edge of the pan.
To prevent the cooktop from discoloring
or staining:
Clean cooktop after each use.
Wipe acidic or sugary spills as soon as the cooktop has
cooled as these spills may discolor the
porcelain.
Unlike a range with standard gas burners,
this cooktop does not lift-up nor is it
removable. Do not attempt to lift the
cooktop for any reason.
Burner Grates
The grates must be properly positioned before cooking.
When installing the grates, place the tab ends toward the
center, matching the straight bars.
Improper installation of the grates may result in chipping of
the cooktop.
Sealed Burners
The sealed burners of your range are secured to the cooktop
and are not designed to be removed. Since the burners are
sealed into the cooktop, boilovers or spills will not seep
underneath the cooktop.
However, the burner should be cleaned after each use. The
cap portion of the burner is easily removed for cleaning. (See
page 6 for cleaning directions.)
The burner caps must be correctly placed on the burner base
for proper operation of the burner.
High Performance Burner
There is one 16,000 BTU* high speed burner on your range,
located in the right front position. This burner offers higher
speed cooking that can be used to quickly bring water to a
boil and for large-quantity cooking.
Low Turn Down Burner
This burner is located in the right rear position. The simmer
burner offers a lower BTU flame for delicate sauces or melting
chocolate.
* BTU ratings will vary when using LP gas.
Dual Ring Burner (select models)
The cooking surface is equipped with a
dual ring burner located in the left front
position. To operate, push in on the
control knob and turn counterclockwise to
light the burner. Continue turning until the
desired setting is reached. The lighting
sequence is: inner burner on High, then
inner burner on Low, then both rings on High,
then both rings on Low.
Do not operate the burners without a pan on the grate.
The grate’s porcelain finish may chip without a pan to
absorb the heat from the burner flame.
Use care when stirring food in a pot/pan sitting on the burner
grate. The grates have a smooth finish for ease of cleaning.
The pot/pan will slide if the handle is not held. This may result
in spilling of hot food items and may be a burn hazard.
Although the burner grates are durable, they will gradually
lose their shine and/or discolor, due to the high temperatures
of the gas flame.
SURFACE COOKING
14
OVEN COOKING
A Rapid Preheat Use to decrease preheating time.
B Convect Use for convection baking and roasting.
C Bake Use for baking and roasting.
D Broil Use for broiling and top browning.
E TIMER 1 Sets timer.
F Display Displays oven functions, options and
window time of day.
G TIMER 2 Sets timer.
H Number Pads Use to enter time and temperature,
or to enter Favorites names.
I Favorites Use to access, program or save
baking cycles.
J More Options Use to access additional features.
K Clean Use to set self-clean cycle.
L Setup Use to view or change factory
default settings.
M Warm Drawer Use to operate the Warming Drawer.
N Oven Light Use to turn the oven light on or off.
O CANCEL Cancels all operations except Timer,
Clock, Favorites, Setup and Warm
Drawer.
P Quickset pads Use to select options in display
window (next to display window
on both sides).
The control panel is designed for ease in programming. The display window shows options for each function and moves from step
to step through the programming process. Control panel features vary by model. Oven display above is programmed for a bake
operation.
A B C D E F G H
Control Panel
Quickset Pads
Quickset pads are located on each side of the display window
and are used to select the desired function or option in the
display window. To select the option or function, press the
Quickset pad next to the word.
Important: Four seconds after entering the function,
option, number or letter, the function will automatically be
entered. If more than 30 seconds elapse between steps in
programming, the function will be canceled and the
display will return to the previous display.
Clock
Setting the Clock:
1. Press the Setup pad.
2. Select CLOCK using the Quickset pads.
3. Select TIME.
4. Enter the time using the number pads.
5. Press Enter pad.
6. Select AM or PM in 12 hour mode. (For 24 hour clock, see
page 15.)
7. To exit the Setup mode, press Setup pad.
If you need to back out of a function or option in the display,
press the Back pad. When your programming is complete,
press the Enter pad or wait four seconds and the function will
start automatically.
Up arrows indicate additional screens with additional options.
Press the Quickset pads next to the arrows to scroll through
the display.
I J K L M N O P
Cont.
15
Activating and canceling the clock/day
of week display:
1. Press Setup pad.
2. Select CLOCK.
3. Press the arrow to scroll until DISABLE is displayed.
4. Select DISABLE.
5. Select TIME.
6. Select OFF to turn the clock display off, or select ON to turn
the clock display on.
7. Select OFF to turn the day of the week display off. Select
ON to turn the weekday display on.
8. To exit the Setup mode, press Setup pad.
Entering the day of the week:
1. Press Setup pad.
2. Select CLOCK.
3. Press the arrow to scroll until DAY is displayed.
4. Use Quickset arrow to scroll through the days.
5. Select day desired.
6. To exit the Setup mode, press Setup pad.
To set the clock for a 12 or 24 hour format:
The clock can be set to display time in either a 12 hour or 24
hour format.
1. Press the Setup pad.
2. Select CLOCK.
3. Use the arrow to scroll to the next screen.
4. Select 12/24 HOUR.
5. Select 12 HR or 24 HR.
6. To exit Setup mode, press Setup pad.
Timers
Setting the Timers (Timer 1 or Timer 2):
1. Press TIMER 1 or TIMER 2 pad.
2. Press one of the displayed times using the
Quickset pads, or press the number pads to
enter the desired time.
Important: Each press of the displayed time choices adds
additional time. For example, pressing “10 MIN” three
times provides 30 minutes on the timer (0:30).
3. Press Enter pad.
Changing the amount of time entered once the
Timer starts:
1. Press the TIMER 1 or TIMER 2 pad once.
2. Press the displayed times on the Quickset pads repeatedly
until the desired time is entered.
OR
3. Press the number pads to enter the new desired time.
4. Press Enter pad.
Canceling the Timer:
1. Press the TIMER 1 or TIMER 2 pad twice.
If both Timers are active:
If the desired Timer is already in the foreground, press once
for edit mode and twice to cancel the Timer. If the desired
Timer is not in the foreground, follow the steps below.
1. Press the desired TIMER pad once. The selected Timer will
come to the foreground.
2. Press the TIMER pad a second time to access the edit
mode in order to make changes.
3. Pressing the TIMER pad a third time will cancel the Timer.
Changing the Timer beeps:
The signal beeps for TIMER 1 and TIMER 2 can be changed.
The options available are two beeps every thirty seconds, two
beeps every sixty seconds or one beep only. The default
setting is one beep.
1. Press the Setup pad.
2. Select the arrow to scroll until TONES
is displayed.
3. Select TONES.
4. Select TIMERS TONES.
5. Select the desired timer beep format (2-30 SEC., 2-60 SEC.
or 1 BEEP).
6. Press Setup pad to exit Setup mode.
Locking the Control and Oven Door
The oven control and oven door can be locked to prevent
accidental programming. If an oven function is currently
being used, the control and door cannot be locked.
To lock the control and door:
Press the Back and Enter pads at the same time, holding for
three seconds or until CONTROL LOCKED appears in the
display.
To unlock the control and door:
Press the Back and Enter pads at the same time, holding for
three seconds. UNLOCKING DOOR will appear in the display
when the control and door are unlocking.
OVEN COOKING
16
Notes:
If more than thirty seconds elapse between pressing a
pad and pressing a number pad, the display will return to
the previous display.
Whenever the temperature appears in the display, the
oven is heating.
To change the oven temperature during cooking, press
the Bake pad and select a displayed temperature or use
the number pads to enter the desired temperature.
The oven will automatically shut off after 12 hours if it is
accidentally left on. To set a Sabbath Mode, see Sabbath
Mode, page 28.
Bake Options
The temperature in the display will increase in 1°
increments until the oven reaches the preset temperature.
Allow about 15 minutes for the oven to preheat.
When the oven is preheated, the oven will beep and
PREHEAT will no longer be displayed.
3. At the end of cooking, turn the oven off by
pressing the CANCEL pad. Remove food
from the oven. The oven will continue
operating until the CANCEL pad is pressed.
Baking
To set Bake:
1. Press the Bake pad.
2. Select the oven temperature using the Quickset pads.
OR
Enter the desired temperature using the number pads.
Press Enter pad to set.
The temperature can be set from 170° F to 550° F
in 5° increments.
After three seconds, the oven will begin to preheat. BAKE
and PREHEAT will appear in the display along with 100°
or the actual oven temperature, whichever is higher.
Do not use delayed baking for highly perishable foods such
as dairy products, pork, poultry or seafood.
Cook & Hold (select models) and Delay options are available
when baking. When using the Cook & Hold option, the oven
begins to heat immediately after the control has been set.
Then, the oven cooks for a specified length of time. When
that time has elapsed, the oven will automatically reduce
temperature to 170° F and keep the food warm for up to an
hour and then automatically turn off.
When using Delay, the oven begins to cook later in the day.
Set the amount of time that you want to delay before the oven
turns on and how long you want to cook. The oven begins to
heat at the selected time and cooks for the specified length of
time. When that time has elapsed, the oven will keep the food
warm for up to an hour then automatically turn off.
17
Convect Bake
To set Convect Bake:
1. Press the Convect pad.
2. Select CNVT BAKE using the Quickset pads.
Convect Options
Cook & Hold (select models) and Delay options are available
when convect cooking. See page 16 for information on how
to program a Cook & Hold or Delay option.
3. Select the oven temperature using the Quickset pads
18
19
5. Place food in the oven and close the door to the broil stop
position.
6. Press the CANCEL pad when broiling
is done.
Broil
For optimal results, preheat for five minutes with the door
closed and use a pan designed for broiling. Oven door should
be open to the broil stop position (about 4 inches) when
broiling.
To set Broil:
1. Place the oven rack in the proper rack position (see
Broiling Chart).
2. Press the Broil pad.
3. Select HIGH – 550° F for high broil.
OR
Select LOW – 450° F for low broil.
The oven has a variable broil feature which means that
a lower broil temperature can be selected (300°-550° F).
To select a lower temperature, press the appropriate
number pads. Press Enter pad to set the lower
temperature.
4. Preheat the oven for five minutes.
Notes:
See Broiling Chart for foods and broiling times.
If more than 30 seconds elapse between pressing the
Broil pad, Quickset pads, or number pads, the oven will
not be set and the display will return to the previous
display.
HIGH is used for most broiling. Use a lower broil
temperature when broiling longer-cooking foods. The
lower temperature allows food to cook to the well done
stage without excessive browning.
Expect broil times to increase and browning to be
slightly lighter if the appliance is installed on a 208 volt
circuit.
Food should be turned halfway through broiling time.
Broil times may be longer when lower broiling
temperatures are selected.
OVEN COOKING
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96

Jenn-Air Range DUAL-FUEL PRO-STYLETM SLIDE-IN RANGE Manuel utilisateur

Taper
Manuel utilisateur