LG OLED77G7V Le manuel du propriétaire

Taper
Le manuel du propriétaire
Please read this manual carefully before operating your set and
retain it for future reference.
www.lg.com
Safety and Reference
P/NO : MFL69727244 (1702-REV00)
Printed in Korea
*MFL69727244*
2
ENGLISH
Warning! Safety instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
uninsulated dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to constitute a risk
of electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING : TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK,
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
Do not place the TV and/or remote control in the following
environments:
- A location exposed to direct sunlight
- An area with high humidity such as a bathroom
- Near any heat source such as stoves and other devices that produce
heat
- Near kitchen counters or humidifiers where they can easily be
exposed to steam or oil
- An area exposed to rain or wind
- Near containers of water such as vases
Otherwise, this may result in fire, electric shock, malfunction or
product deformation.
Do not place the product where it might be exposed to dust. This may
cause a fire hazard.
Mains Plug is the TV connecting/disconnecting device to AC mains
electric supply. This plug must remain readily attached and operable
when TV is in use.
Do not touch the power plug with wet hands. Additionally, if the cord
pin is wet or covered with dust, dry the power plug completely or
wipe dust off. You may be electrocuted due to excess moisture.
Make sure to connect Mains cable to compliant AC mains socket with
Grounded earth pin. (Except for devices which are not grounded on
earth.) Otherwise possibility you may be electrocuted or injured.
Insert power cable plug completely into wall socket otherwise if not
secured completely into socket, fire ignition may break out.
Ensure the power cord does not come into contact with hot objects
such as a heater. This may cause a fire or an electric shock hazard.
Do not place a heavy object, or the product itself, on power cables.
Otherwise, this may result in fire or electric shock.
Bend antenna cable between inside and outside building to prevent
rain from flowing in. This may cause water damaged inside the
Product and could give an electric shock.
When mounting TV onto wall make sure to neatly install and isolate
cabling from rear of TV as to not create possibility of electric shock /
fire hazard.
Do not plug too many electrical devices into a single multiple
electrical outlet. Otherwise, this may result in fire due to over-
heating.
Do not drop the product or let it fall over when connecting external
devices. Otherwise, this may result in injury or damage to the
product.
Keep the anti-moisture packing material or vinyl packing out of the
reach of children. Anti-moisture material is harmful if swallowed. If
swallowed by mistake, force the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can cause suffocation. Keep it out
of the reach of children.
Do not let your children climb or cling onto the TV.
Otherwise, the TV may fall over, which may cause serious injury.
Dispose of used batteries carefully to ensure that a small child
does not consume them. Please seek Doctor- Medical Attention
immediately if child consumes batteries.
Do not insert any metal objects/conductors (like a metal chopstick/
cutlery/screwdriver) into the end of power cable while the power
plug is plugged into wall socket. Additionally, do not touch the
power plug right after unplugging from the wall socket. You may be
electrocuted.
3
ENGLISH
Do not put or store inflammable substances near the product. There is
a danger of combustion/explosion or fire due to careless handling of
the inflammable substances.
Do not drop metallic objects such as coins, hair pins, chopsticks or
wire into the product, or inflammable objects such as paper and
matches. Children must pay particular attention. Electrical shock, fire
or injury can occur. If a foreign object is dropped into the product,
unplug the power cord and contact the service centre.
Do not spray water on the product or scrub with an inflammable
substance (thinner or benzene). Fire or electric shock accident can
occur.
Do not allow any impact, shock or any objects to fall into the unit,
and do not drop anything onto the screen. You may be injured or the
product can be damaged.
Never touch this product or antenna during a thunder or lighting
storm.
You may be electrocuted.
Never touch the wall outlet when there is leakage of gas, open the
windows and ventilate. It may cause a fire or a burn by a spark.
Do not disassemble, repair or modify the product at your own
discretion. Fire or electric shock accident can occur.
Contact the service centre for check, calibration or repair.
If any of the following occur, unplug the product immediately and
contact your local service centre.
- The product has been damaged
- Foreign objects have entered the product
- The product produced smoke or a strange smell
This may result in fire or electric shock.
Unplug the TV from AC mains wall socket if you do not intend to
use the TV for a long period of time. Accumulated dust can cause
fire hazard and insulation deterioration can cause electric leakage/
shock/fire.
Apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall be placed on the
apparatus.
Do not install this product on a wall if it could be exposed to oil or oil
mist. This may damage the product and cause it to fall.
If water enters or comes into contact with TV, AC adapter or power
cord please disconnect the power cord and contact service centre
immediately. Otherwise, this may result in electric shock or fire.
Only use an authorized AC adapter and power cord approved by
LG Electronics. Otherwise, this may result in fire, electric shock,
malfunction or product deformation.
Never Disassemble the AC adapter or power cord. This may result in
fire or electric shock.
Be careful in handling the adapter to prevent any external shocks to
it. An external shock may cause damage to the adapter.
Make sure the power cord is connected securely to the power plug
on the TV.
Install the product where no radio wave occurs.
There should be enough distance between an outside antenna and
power lines to keep the former from touching the latter even when
the antenna falls. This may cause an electric shock.
Do not install the product on places such as unstable shelves or
inclined surfaces. Also avoid places where there is vibration or where
the product cannot be fully supported. Otherwise, the product may
fall or flip over, which may cause injury or damage to the product.
If you install the TV on a stand, you need to take actions to prevent
the product from overturning. Otherwise, the product may fall over,
which may cause injury.
If you intend to mount the product to a wall, attach VESA standard
mounting interface (optional parts) to the back of the product. When
you install the set to use the wall mounting bracket (optional parts),
fix it carefully so as not to drop. (Only OLED65/77G7*)
Only use the attachments / accessories specified by the manufacturer.
When installing the antenna, consult with a qualified service
technician. If not installed by a qualified technician, this may create a
fire hazard or an electric shock hazard.
We recommend that you maintain a distance of at least 2 to 7 times
the diagonal screen size when watching TV. If you watch TV for a long
period of time, this may cause blurred vision.
Only use the specified type of battery. This could cause damage to the
remote control.
Do not mix new batteries with old batteries. This may cause the
batteries to overheat and leak.
Batteries should not be exposed to excessive heat. For example, keep
away from direct Sunlight, open fireplace and electric heaters.
4
ENGLISH
Signal from Remote Control can be interrupted due to external/
internal lighting eg Sunlight, fluorescent lighting. If this occurs turn
off lighting or darken viewing area.
When connecting external devices such as video game consoles,
make sure the connecting cables are long enough. Otherwise, the
product may fall over, which may cause injury or damage the product.
Do not turn the product On/Off by plugging-in or unplugging the
power plug to the wall outlet. (Do not use the power plug for switch.)
It may cause mechanical failure or could give an electric shock.
Please follow the installation instructions below to prevent the
product from overheating.
- The distance between the product and the wall should be more
than 10cm.
- Do not install the product in a place with no ventilation (e.g., on a
bookshelf or in a cupboard).
- Do not install the product on a carpet or cushion.
- Make sure the air vent is not blocked by a tablecloth or curtain.
This may result in fire.
Take care not to touch the ventilation openings when watching the
TV for long periods as the ventilation openings may become hot. This
does not affect the operation or performance of the product.
Periodically examine the cord of your appliance, and if its appearance
indicates damage or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact replacement part
by an authorized servicer.
Prevent dust collecting on the power plug pins or outlet. This may
cause a fire hazard.
Protect the power cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and the point where the
cord exits the appliance.
Do not press strongly upon the panel with a hand or sharp object
such as nail, pencil or pen, or make a scratch on it, as it may
causedamage to screen.
Avoid touching the screen or holding your finger(s) against it for long
periods of time. Doing so may produce some temporary or permanent
distortion/damage to screen.
As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn off this unit
by SWITCH.
When unplugging the cable, grab the plug and unplug it, by pulling
at the plug. Don’t pull at the cord to unplug the power cord from the
power board, as this could be hazardous.
When moving the product, make sure you turn the power off first.
Then, unplug the power cables, antenna cables and all connecting
cables.
The TV set or power cord may be damaged, which may create a fire
hazard or cause electric shock.
When moving or unpacking the product, work in pairs because the
product is heavy. Otherwise, this may result in injury.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power
supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
Do not use high voltage electrical goods near the TV (e.g. electric
mosquito-swatter). This may result in product malfunction.
When cleaning the product and its components, unplug the power
first and wipe it with a soft cloth. Applying excessive force may cause
scratches or discolouration. Do not spray the panel with water or wipe
with a wet cloth. Never use glass cleaner, car or industrial shiner,
abrasives or wax, benzene, alcohol etc., which can damage the
product and its panel. Otherwise, this may result in fire, electric shock
or product damage (Deformation, corrosion or breakage).
When cleaning the top surface of the Companion Box (AV Box), spray
water on a soft cloth and then wipe gently. Do not spray directly on
the Companion Box (AV Box). (Only OLED65/77W7*)
5
ENGLISH
Preparing
If the TV is turned on for the first time after it was shipped from the
factory, initialization of the TV may take a few minutes.
Image shown may differ from your TV.
Your TV’s OSD (On Screen Display) may differ slightly from that shown
in this manual.
The available menus and options may differ from the input source or
product model that you are using.
New features may be added to this TV in the future.
The items supplied with your product may vary depending on the
model.
Product specifications or contents of this manual may be changed
without prior notice due to upgrade of product functions.
For an optimal connection, HDMI cables and USB devices should have
bezels less than 10 mm thick and 18 mm width. Use an extension
cable that supports USB 2.0 if the USB cable or USB memory stick
does not fit into your TV’s USB port.
A
B
A
B
* A
<
=
10 mm
* B
<
=
18 mm
Use a certified cable with the HDMI logo attached.
If you do not use a certified HDMI cable, the screen may not display or
a connection error may occur. (Recommended HDMI Cable Types)
- High-Speed HDMI
®
/
TM
Cable (3 m or less)
- High-Speed HDMI
®
/
TM
Cable with Ethernet (3 m or less)
When supported cable is not long enough to connect
TV set with Companion Box (AV Box), you can use an
extension cable. (Only OLED65/77W7V)
Please do not pile the stuff up or press strongly
the speaker. This may result in product damage or
degradation. (Only OLED65/77W7*)
Do not use any unapproved items to ensure the safety
and product life span.
Any damage or injuries caused by using unapproved
items are not covered by the warranty.
Some models have a thin film attached on to the
screen and this must not be removed.
When attaching the stand to the TV set, place the
screen facing down on a cushioned table or flat surface
to protect the screen from scratches.
Make sure that the screws are fastened completely. (If
they are not fastened securely enough, the TV may tilt
forward after being installed.) Do not use too much
force and over tighten the screws; otherwise screw
may be damaged and not tighten correctly.
Make sure to wring any excess water or cleaner from
the cloth.
Do not spray water or cleaner directly onto the TV
screen.
Make sure to spray just enough of water or cleaner
onto a dry cloth to wipe the screen.
Separate purchase
Separate purchase items can be changed or modified for quality
improvement without any notification. Contact your dealer to buy
these items. These devices only work with certain models. The model
name or design may be changed depending on the upgrade of product
functions, manufacturer’s circumstances or policies.
(Depending on model)
AN-MR650A
Magic Remote
6
ENGLISH
Lifting and moving the TV
Please note the following advice to prevent the TV from being scratched
or damaged and for safe transportation regardless of its type and size.
It is recommended to move the TV in the box or packing material that
the TV originally came in.
Before moving or lifting the TV, disconnect the power cord and all
cables.
When holding the TV, the screen should face away from you to avoid
damage.
Hold the top and bottom of the TV frame firmly. Make sure not to
hold the transparent part, speaker, or speaker grill area.
When transporting a large TV, there should be at least 2 people.
When transporting the TV by hand, hold the TV as shown in the
following illustration.
When transporting the TV, do not expose the TV to jolts or excessive
vibration.
When transporting the TV, keep the TV upright, never turn the TV on
its side or tilt towards the left or right.
Do not apply excessive pressure to cause flexing /bending of frame
chassis as it may damage screen.
When handling the TV, be careful not to damage the protruding
buttons.
Avoid touching the screen at all times, as this may
result in damage to the screen.
Do not move the TV by holding the cable holders, as
the cable holders may break, and injuries and damage
to the TV may occur.
Make sure to attach the AV box fixing supporter to the
AV box before you lift the product and move. Moving
the product without attaching the AV box fixing
supporter to the AV box first may cause injury to your
fingers. (Only OLED65/77G7*)
Using the button
(Depending on model)
You can simply operate the TV functions, using the button.
<A type>
<B type>
7
ENGLISH
Basic functions
Power On (Press)
Power Off (Press and hold)
1
Volume Control
Programmes Control
1 All running apps will close, and any recording in progress will stop.
Adjusting the menu
When the TV is turned on, press the button one time. You can adjust
the Menu items using the button.
Turns the power off.
Clears on-screen displays and returns to TV viewing.
Changes the input source.
Accesses the settings menu.
Mounting on a table
(This feature is not available for all models.)
1 Lift and tilt the TV into its upright position on a table.
• Leave a 10 cm (minimum) space from the wall for proper
ventilation.
10 cm
10 cm
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
Do not place the TV near or on sources of heat, as this
may result in fire or other damage.
Do not apply foreign substances (oils, lubricants, etc.)
to the screw parts when assembling the product.
(Doing so may damage the product.)
Securing the TV to a wall
(This feature is not available for all models.)
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the
back of the TV.
• If there are bolts inserted at the eye-bolts position, remove the
bolts first.
2 Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the rear
of the TV.
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.
Make sure to keep the rope horizontal with the flat surface.
Make sure that children do not climb on or hang on
the TV.
Use a platform or cabinet that is strong and large enough to support
the TV securely.
Brackets, bolts and ropes are not provided. You can obtain additional
accessories from your local dealer.
8
ENGLISH
Mounting on a wall
(This feature is not available for all models.)
10 cm
10 cm
10 cm
10 cm
(Only OLED65/77G7*)
Attach an optional wall mount bracket at the rear of the TV carefully
and install the wall mount bracket on a solid wall perpendicular to
the floor. When you attach the TV to other building materials, please
contact qualified personnel. LG recommends that wall mounting be
performed by a qualified professional installer. We recommend the use
of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with
cables connected. When you do not use LG’s wall mount bracket, please
use a wall mount bracket where the device is adequately secured to the
wall with enough space to allow connectivity to external devices. It is
advised to connect all the cables before installing fixed wall mounts.
Make sure to use screws and wall mount bracket that meet the VESA
standard. Standard dimensions for the wall mount kits are described in
the following table.
Separate purchase (Wall mounting bracket)
Model OLED65G7* OLED77G7*
VESA (A x B) (mm) 400 x 200 600 x 300
Standard screw M6 M8 M4
Number of screws 4 4 2
Wall mount bracket OTW420B OTW630B
A
B
A
B
Fold the AV box before installing the TV on a wall
mount by performing the stand type installation in
reverse.
To install the wall mount, switch the selector to
as shown in the figure below. (Only
OLED77G7*)
Fold the AV box and attach the AV box fixing supporter / Wall mount
spacer to the AV box before installing the product on a wall mount.
(Only when the item of the following form is provided)
Provided item
AV box fixing supporter x 2
1
2
9
ENGLISH
Provided item
AV box fixing supporter /
Wall mount spacer
Wall mount spacer
x 2 x 2 x 2
(Only OLED65/77W7V)
Provided item
Wall mounting anchor Wall mounting screw
Wall mount Punching Guide
Check the material of the wall and the thickness of the finishing.
Use the Wall mount anchor for wall material of concrete, light
concrete, strong natural stone, soft natural stone masonry brick and
hallow block that do not crack.
Wall Material Tools Wall Width
Concrete
Wall mounting
anchor, Wall
mounting screw,
Ø 3/6/8 mm Drill bit
70 mm
Brick
Natural stone
Metal Panel
Plywood
Wall mounting
screw, Ø 3 mm
Drill bit
30 mm
EPS Panel Penetrate the wall
Plasterboard +
Plywood
30 mm
Do not mount the device on the walls made from plasterboard or
medium density fiberboard (MDF). In this case, the anchor and screws
must be inserted into the concrete behind the finish surface. If there
is no concrete on the other side, then you must first install a separate
hanger to securely install the anchors and screws.
When installing the product on wall material not designated, install
the product so that each location can withstand the pull out load of
70 kgf (686 N) and shear load of 100 kgf (980 N) or above.
Use the Ø 8 mm drill bit for concrete and hammer (Impact) drill.
Tools you will need
Phillips head + driver (manual or motorized), Ø 3/6/8 mm Drill bit,
Level, Stud finder, Drill
10
ENGLISH
How to attach to masonry walls
Please follow the below direction.
1 Use a drill bit Ø 8 mm to drill a hole for the anchor location within a
depth of 80 mm to 100 mm.
2 Clean the drilled hole.
3 Insert the sealed wall mounting anchor to the hole. (When inserting
the anchor, use a hammer.)
Wall mounting anchor
4 Set the wall mount on the wall by aligning to the location of the
hole. And, set the angle adjusting part to face upward.
Wall mount
5 Align the wall mounting screw to the hole and tighten it. Then,
fasten the screws at torque of 45 kgf/cm to 60 kgf/cm.
Wall mounting screw
Make sure that children do not climb on or hang on
the TV.
Use a platform or cabinet that is strong and large
enough to support the TV securely.
When installing the product, first check that the wall is
strong enough. Use the anchors and screws provided.
- If you use anchors and screws that are not specified
by the manufacturer, they may not hold the weight
of the product, causing safety issues.
Be sure to use the accessory cable provided.
Otherwise, friction between the product and the wall
may cause damage to the connector.
When drilling holes into the wall, make sure you use
a drill and drill bit with the specified diameter. Ensure
that you also follow the instructions regarding the
depth of the holes.
- Otherwise, the product may be installed incorrectly
and cause safety issues.
Wear safety gloves when installing the product. Do not
use your bare hands.
- Otherwise, it may cause personal injury.
If some parts of the wall mount do not touch the wall
after it is attached, use the double-sided tape included
in the accessory box to stick the mount to the wall.
If you want to connect the TV Cable is connected to
the back panel partition, please use the enclosed
Punching Guide.
11
ENGLISH
Using the kensington security
system
(Only OLED65W7*)
The Kensington security system connector is located at the rear of
the Companion Box (AV Box). For more information of installation
and using, refer to the manual provided with the Kensington security
system or visit http://www.kensington.com.
Connections (notifications)
Connect various external devices to the TV and switch input modes to
select an external device. For more information of external devices
connection, refer to the manual provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio
systems, USB storage devices, PC, gaming devices, and other external
devices.
The external device connection may differ from the model.
Connect external devices to the TV regardless of the order of the TV
port.
If you record a TV program on a DVD recorder or VCR, make sure to
connect the TV signal input cable to the TV through a DVD recorder or
VCR. For more information of recording, refer to the manual provided
with the connected device.
Refer to the external equipment’s manual for operating instructions.
If you connect a gaming device to the TV, use the cable supplied with
the gaming device.
In PC mode, there may be noise associated with the resolution,
vertical pattern, contrast or brightness. If noise is present, change the
PC output to another resolution, change the refresh rate to another
rate or adjust the brightness and contrast on the PICTURE menu until
the picture is clear.
In PC mode, some resolution settings may not work properly
depending on the graphics card.
If ULTRA HD content is played on your PC, video or audio may become
disrupted intermittently depending on your PC’s performance.
When connecting via a wired LAN, it is recommended to use a
CAT 7 cable.
Antenna connection
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
Use a signal splitter to use more than 2 TVs.
If the image quality is poor, install a signal amplifier properly to
improve the image quality.
If the image quality is poor with an antenna connected, try to realign
the antenna in the correct direction.
An antenna cable and converter are not supplied.
Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus,
HE-AAC
For a location that is not supported with ULTRA HD broadcasting,
this TV cannot receive ULTRA HD broadcasts directly. (Depending on
model)
Satellite dish connection
(Only satellite models)
Connect the TV to a satellite dish to a satellite socket with a satellite RF
cable (75 Ω).
CI module connection
(Depending on model)
View the encrypted (pay) services in digital TV mode.
Check if the CI module is inserted into the PCMCIA card slot in the
right direction. If the module is not inserted properly, this can cause
damage to the TV and the PCMCIA card slot.
If the TV does not display any video and audio when CI+ CAM is
connected, please contact to the Terrestrial/Cable/Satellite Service
Operator.
USB connection
Some USB Hubs may not work. If a USB device connected through a USB
Hub is not detected, connect it directly to the USB port on the TV.
12
ENGLISH
Other connections
Connect your TV to external devices. For the best picture and audio
quality, connect the external device and the TV with the HDMI cable.
Some separate cable is not provided.
General HDMI ULTRA HD Deep Colour :
- On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0)
- Off : Support 4K @ 50/60 Hz 8 bit (4:2:0)
If the device connected to Input Port also supports ULTRA HD Deep
Colour, your picture may be clearer.
However, if the device doesn’t support it, it may not work properly.
In that case, connect the device to a different HDMI port or change the
TV’s HDMI ULTRA HD Deep Colour setting to Off.
Supported HDMI Audio format :
DTS (44.1 kHz, 48 kHz),
Dolby Digital / Dolby Digital Plus (32 kHz, 44.1 kHz, 48 kHz),
PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz)
(Depending on model)
Slim remote control
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the TV correctly.
To replace coin batteries, turn the battery cover counterclockwise by
using a coin. Take the battery cover off and insert the battery (CR2032)
facing forward . Put the battery cover on the remote control and
turn it clockwise to close. To remove the coin batteries, perform the
installation actions in reverse.
Make sure to point the remote control toward the remote control sensor
on the TV.
EXIT
BACK
STB
PWR
A
A
(POWER) Turns the TV on or off.
You can turn your set-top box on or off by adding the set-top
box to the universal remote control for your TV.
Adjusts the volume level.
Scrolls through the saved programmes.
(MUTE) Mutes all sounds.
Returns to the previous level.
* Clears on-screen displays and returns to last input viewing.
(HOME) Accesses the Home menu.
(INPUT) Changes the input source.
- Pressing and holding the button displays all the lists of external
inputs.
Selects menus or options and confirms your input.
Navigation buttons (up/down/left/right)
Press the up, down, left or right button to scroll the menu.
* To use the button, press and hold for more than 3 seconds.
Battery installation
DO NOT INGEST BATTERY. CHEMICAL BURN HAZARD.
The battery used in this device may present a fire or
chemical burn hazard if mistreated. Do not recharge,
disassemble, incinerate, or heat above 100 °C. Replace
the battery part no. CR2032 only. Use of another
battery may present a risk of fire or explosion. Dispose
of used battery. Keep battery away from children. Do
not disassemble or dispose of in fire.
[The remote control supplied with] This product
contains a coin/button cell battery. If the coin/button
cell battery is swallowed, it can cause severe internal
burns in just 2 hours and can lead to death. Keep new
and used batteries away from children. If the battery
compartment does not close securely, stop using
the product and keep it away from children. If you
think batteries might have been swallowed or placed
inside any part of the body, seek immediate medical
attention.
If you have long nails, do not open the battery cover by
using your finger. Or else, your nail could break.
13
ENGLISH
Magic remote functions
When the message “Magic remote battery is low. Change the battery. is
displayed, replace the battery.
To replace batteries, open the battery cover, replace batteries (1.5 V AA)
matching the and ends to the label inside the compartment,
and close the battery cover. Be sure to point the magic remote toward
the remote control sensor on the TV. To remove the batteries, perform
the installation actions in reverse.
It is recommended that an Access Point (AP) be located more than
0.2 m away from the TV. If the AP is installed closer than 0.2 m the
Magic remote may not work properly due to frequency interference.
Some buttons and services may not be provided depending on
models or regions.
GUIDE
LIST
STB
TEXT
T.OPT
FOCUS
MENU
RECENT
EXIT
BACK
LIVE ZOOM
STB
PWR
6
mno
9
wxyz
3
def
2
abc
1
. @
4
ghi
8
tuv
7
pqrs
0
5
jkl
/
/
A
A
(POWER) Turns the TV on or off.
You can turn your set-top box on or off by adding the set-top
box to the universal remote control for your TV.
Number buttons Enters numbers.
Alphabet buttons Enters letters.
(Space) Opens an empty space on the screen keyboard.
Accesses the saved programmes list.
(Screen Remote) Displays the Screen Remote.
- Accesses the Universal Control Menu.
* You can access apps or Live TV using the number
buttons corresponding to the features.
* Audio descriptions function will be enabled.
Adjusts the volume level.
Scrolls through the saved programmes.
(MUTE) Mutes all sounds.
(Voice recognition)
Network connection is required to use the voice recognition function.
1 Press the voice recognition button.
2 Speak when the voice display window appears on the TV screen.
(SEARCH)* Search for content such as TV programmes, movies and
other videos, or perform a web search by entering text in the search bar.
GUIDE
LIST
STB
TEXT
T.OPT
FOCUS
MENU
RECENT
EXIT
BACK
LIVE ZOOM
STB
PWR
6
mno
9
wxyz
3
def
2
abc
1
. @
4
ghi
8
tuv
7
pqrs
0
5
jkl
/
/
B
1
2
1
B
(HOME) Accesses the Home menu.
* Shows the previous history.
1
Displays the set-top box Home menu.
- When you are not watching via a set-top box: the display changes to
the set-top box screen.
Wheel (OK) Press the center of the Wheel button to select a menu.
You can change programmes by using the Wheel button.
Navigation buttons (up/down/left/right)
Press the up, down, left or right button to scroll the menu.
If you press buttons while the pointer is in use, the pointer
will disappear from the screen and Magic Remote will operate like a
general remote control. To display the pointer on the screen again, shake
Magic Remote to the left and right.
Returns to the previous level.
* Clears on-screen displays and returns to last input viewing.
Shows programmes guide.
14
ENGLISH
1
2
Streaming Service buttons Connects to the Video Streaming
Service.
(INPUT) Changes the input source.
- Pressing and holding the button displays all the lists of external
inputs.
1
(Q. Settings) Accesses the Quick Settings.
- Pressing and holding the button displays the All Settings menu.
Teletext buttons ( , ) These buttons are used for teletext.
* Provides content related to the programme you are
currently watching.
Views the information of the current programme and screen.
Control buttons ( ) Controls media contents.
By zooming in on the selected area, you can view it in full
screen.
* You can zoom in on the area where the remote control is
pointed.
, , , These access special functions in some menus.
* To use the button, press and hold for more than 3 seconds.
Registering magic remote
How to register the magic remote
To use the Magic Remote, first pair it with your TV.
1 Put batteries into the Magic Remote and turn the TV on.
2 Point the Magic Remote at your TV and press the Wheel (OK)
on the remote control.
* If the TV fails to register the Magic Remote, try again after turning the
TV off and back on.
How to deregister the magic remote
Press the and (HOME) buttons at the same time, for five
seconds, to unpair the Magic Remote with your TV.
* Pressing and holding the button will let you cancel and re-
register Magic Remote at once.
Licenses
Supported licenses may differ by model. For more information about
licenses, visit www.lg.com.
Open source software
notice information
To obtain the source code under GPL, LGPL, MPL, and other open source
licenses, that is contained in this product, please visit
http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty
disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM
for a charge covering the cost of performing such distribution (such
as the cost of media, shipping, and handling) upon email request to
opensourc[email protected]. This offer is valid for three (3) years from the date
on which you purchased the product.
External control device
setup
To obtain the external control device setup information, please visit
www.lg.com.
15
ENGLISH
Troubleshooting
Cannot control the TV with the remote control.
Check the remote control sensor on the product and try again.
Check if there is any obstacle between the product and the remote
control.
Check if the batteries are still working and properly installed ( to
, to ).
No image display and no sound is produced.
Check if the product is turned on.
Check if the power cord is connected to a wall outlet.
Check if there is a problem in the wall outlet by connecting other
products.
The TV turns off suddenly.
Check the power control settings. The power supply may be
interrupted.
Check if the Sleep Timer / Timer Power Off is activated in the
Timers settings.
Check if the Auto Power Off is activated in the General Eco
Mode settings. (Depending on model)
If there is no signal while the TV is on, the TV will turn off
automatically after 15 minutes of inactivity.
When connecting to the PC (HDMI), No Signal or ‘Invalid Format is
displayed.
Turn the TV off/on using the remote control.
Reconnect the HDMI cable.
Restart the PC with the TV on.
Abnormal Display
If the product feels cold to the touch, there may be a small “flicker”
when it is turned on. This is normal, there is nothing wrong with
product.
This panel is an advanced product that contains millions of pixels.
You may see tiny black dots and/or brightly coloured dots (white, red,
blue or green) at a size of 1ppm on the panel. This does not indicate
a malfunction and does not affect the performance and reliability of
the product.
This phenomenon also occurs in third-party products and is not
subject to exchange or refund.
You may find different brightness and color of the panel depending
on your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is
not related with the product performance, and it is not malfunction.
Displaying a still image for a prolonged period of time may cause
image sticking. Avoid displaying a fixed image on the TV screen for a
long period of time.
Some horizontal lines may appear when the Pixel Refresher feature is
performed. It is normal and there is no need to be concerned.
(Only OLED65/77W7*)
A blue light blinks on the front of the Companion Box (AV Box).
- The TV may have a problem with the cooling fan or the
temperature in the TV may be too high. Contact an authorized
service center.
A magenta light blinks on the front of the Companion Box (AV
Box).
- The TV may have a problem in the moving speaker. Contact an
authorized service center.
An orange light blinks on the front of the Companion Box (AV
Box).
- The cable from panel may not be properly connected to the
Companion Box (AV Box). Unplug the power cord and reconnect
the cable and then plug the power cord and press the power
button. If it still doesn’t work after the steps above, contact an
authorized service center.
16
ENGLISH
Generated Sound
“Cracking noise: A cracking noise that occurs when watching or
turning off the TV is generated by plastic thermal contraction due to
temperature and humidity. This noise is common for products where
thermal deformation is required.
Electrical circuit humming/panel buzzing: A low level noise is
generated from a high-speed switching circuit, which supplies a large
amount of current to operate a product. It varies depending on the
product.
This generated sound does not affect the performance and reliability
of the product.
Specifications
Wireless module specifications
As band channels can vary per country, the user cannot change or
adjust the operating frequency. This product is configured for the
regional frequency table.
For consideration of the user, this device should be installed and
operated with a minimum distance of 20 cm between the device and
the body.
Wireless module(LGSBWAC72)specifications
Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency range Output power(Max.)
2400 to 2483.5 MHz
5150 to 5725 MHz
5725 to 5850 MHz (Not for EU)
14 dBm
16.5 dBm
11.5 dBm
Bluetooth
Frequency range Output power(Max.)
2400 to 2483.5 MHz 8.5 dBm
* "IEEE 802.11ac" is not available in all countries.
CI Module (W x H x D)
100.0 mm x 55.0 mm x
5.0 mm
Environment
condition
Operating
Temperature
0 °C to 40 °C
Operating
Humidity
Less than 80 %
Storage
Temperature
-20 °C to 60 °C
Storage Humidity Less than 85 %
17
ENGLISH
(Depending on country)
Digital TV Analogue TV
Television system
DVB-T
DVB-T2
DVB-C
DVB-S/S2
PAL/SECAM, B/G, D/K, I
SECAM L
Channel coverage
(Band)
DVB-S/S2 DVB-C DVB-T/T2
46 ~ 862 MHz
950 ~ 2150 MHz 46 ~ 890 MHz
VHF III : 174 ~ 230 MHz
UHF IV : 470 ~ 606 MHz
UHF V : 606 ~ 862 MHz
S Band II : 230 ~ 300 MHz
S Band III : 300 ~ 470 MHz
Maximum number of
storable programmes
6,000 2,000
External antenna
impedance
75 Ω
MODEL
SERIAL
Record the model number and serial number of
the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring
any service.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

LG OLED77G7V Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues