Foundry Networks FES12GCF Guide d'installation

Foundry FastIron Stackable

Hardware Installation Guide

FastIron Edge Switch

FastIron Edge Switch X-Series

FastIron Workgroup Switch X-Series

4980 Great America Parkway

Santa Clara, CA 95054

Tel 408.207.1700

www.foundrynet.com

June 2006

™

No part of this work may be reproduced in any form or by any means – graphic, electronic or mechanical, including

photocopying, recording, taping or storage in an information retrieval system – without prior written permission of the

copyright owner.

The trademarks, logos and service marks ("Marks") displayed herein are the property of Foundry or other third parties.

You are not permitted to use these Marks without the prior written consent of Foundry or such appropriate third party.

Foundry Networks, BigIron, FastIron, IronView, JetCore, NetIron, ServerIron, TurboIron, IronWare, EdgeIron, IronPoint,

the Iron family of marks and the Foundry Logo are trademarks or registered trademarks of Foundry Networks, Inc. in

the United States and other countries.

F-Secure is a trademark of F-Secure Corporation. All other trademarks mentioned in this document are the property of

their respective owners.

June 2006 © Foundry Networks, Inc. iii

Contents

C

HAPTER

1

A

BOUT

T

HIS

G

UIDE

..................................................................................... 1-1

INTRODUCTION ...........................................................................................................................................1-1

W

HAT’S INCLUDED IN THIS EDITION? ...........................................................................................................1-2

A

UDIENCE ..................................................................................................................................................1-3

N

OMENCLATURE .........................................................................................................................................1-3

R

ELATED PUBLICATIONS .............................................................................................................................1-3

H

OW TO GET HELP .....................................................................................................................................1-4

W

EB ACCESS .......................................................................................................................................1-4

E

MAIL ACCESS .....................................................................................................................................1-4

T

ELEPHONE ACCESS ............................................................................................................................1-4

W

ARRANTY COVERAGE ...............................................................................................................................1-4

C

HAPTER

2

P

RODUCT

O

VERVIEW

.................................................................................. 2-1

PRODUCT OVERVIEW ..................................................................................................................................2-1

S

UPPORTED CONFIGURATIONS .............................................................................................................2-2

S

OFTWARE FEATURES ................................................................................................................................2-3

POE A

PPLICATIONS ....................................................................................................................................2-3

W

IRELESS APPLICATIONS ............................................................................................................................2-3

H

ARDWARE FEATURES ...............................................................................................................................2-4

FES2402, FES4802, FES9604 ..........................................................................................................2-4

FES12GCF .........................................................................................................................................2-5

FES2402-POE

AND FES4802-POE ...................................................................................................2-5

FESX424, FESX624,

AND FWSX424 ................................................................................................2-6

FESX424HF .......................................................................................................................................2-6

FESX424-POE ...................................................................................................................................2-7

FESX448, FESX648,

AND FWSX448 .................................................................................................2-7

C

ONTROL FEATURES ............................................................................................................................2-8

F

IBER OPTIC MODULES ......................................................................................................................2-15

Foundry Hardware Installation Guide for the FES, FESX, and FWSX

iv © Foundry Networks, Inc. June 2006

POWER SUPPLIES ..............................................................................................................................2-17

C

OOLING SYSTEM AND FANS ..............................................................................................................2-20

C

HAPTER

3

I

NSTALLING

A

F

AST

I

RON

S

TACKABLE

S

WITCH

............................................. 3-1

UNPACKING A SYSTEM ................................................................................................................................3-1

P

ACKAGE CONTENTS ...........................................................................................................................3-2

G

ENERAL REQUIREMENTS ....................................................................................................................3-2

S

UMMARY OF INSTALLATION TASKS .............................................................................................................3-3

I

NSTALLATION PRECAUTIONS .......................................................................................................................3-4

G

ENERAL PRECAUTIONS .......................................................................................................................3-4

L

IFTING PRECAUTIONS .........................................................................................................................3-4

P

OWER PRECAUTIONS .........................................................................................................................3-4

P

REPARING THE INSTALLATION SITE ............................................................................................................3-6

C

ABLING INFRASTRUCTURE ..................................................................................................................3-6

I

NSTALLATION LOCATION ......................................................................................................................3-6

I

NSTALLING A REDUNDANT POWER SUPPLY .................................................................................................3-6

I

NSTALLING AN AC POWER SUPPLY ......................................................................................................3-6

I

NSTALLING A DC POWER SUPPLY ........................................................................................................3-7

I

NSTALLING THE DEVICE ..............................................................................................................................3-8

D

ESKTOP INSTALLATION .......................................................................................................................3-8

R

ACK MOUNT INSTALLATION .................................................................................................................3-8

W

ALL MOUNT INSTALLATION .................................................................................................................3-9

P

OWERING ON THE SYSTEM .......................................................................................................................3-9

V

ERIFYING PROPER OPERATION .................................................................................................................3-9

O

BSERVING THE POWER STATUS LEDS ..............................................................................................3-10

A

TTACHING A PC OR TERMINAL ................................................................................................................3-10

C

HAPTER

4

C

ONNECTING

N

ETWORK

D

EVICES

AND

C

HECKING

C

ONNECTIVITY

........................................................................... 4-1

ASSIGNING PERMANENT PASSWORDS .........................................................................................................4-1

R

ECOVERING FROM A LOST PASSWORD ................................................................................................4-2

C

ONFIGURING IP ADDRESSES .....................................................................................................................4-3

D

EVICES RUNNING LAYER 3 SOFTWARE ...............................................................................................4-3

D

EVICES RUNNING LAYER 2 SOFTWARE ...............................................................................................4-4

C

ONNECTING NETWORK DEVICES ...............................................................................................................4-5

C

ONNECTORS ......................................................................................................................................4-5

C

ABLE SPECIFICATIONS ........................................................................................................................4-5

C

ONNECTING TO ETHERNET OR FAST ETHERNET HUBS .........................................................................4-5

C

ONNECTING TO WORKSTATIONS, SERVERS, OR ROUTERS ...................................................................4-6

C

ONNECTING A NETWORK DEVICE TO A FIBER PORT .............................................................................4-6

T

ESTING CONNECTIVITY ..............................................................................................................................4-7

P

INGING AN IP ADDRESS ......................................................................................................................4-7

O

BSERVING LEDS ................................................................................................................................4-8

Contents

June 2006 © Foundry Networks, Inc. v

TRACING A ROUTE ...............................................................................................................................4-9

T

ROUBLESHOOTING NETWORK CONNECTIONS ...........................................................................................4-10

U

SING VIRTUAL CABLE TESTING TO DIAGNOSE A CABLE .....................................................................4-10

C

HAPTER

5

M

ANAGING

THE

F

AST

I

RON

S

TACKABLE

C

HASSIS

......................................... 5-1

MANAGING FES TEMPERATURE SETTINGS ..................................................................................................5-1

M

ANAGING THE FESX AND FWSX FAN SETTINGS AND

T

EMPERATURE SENSORS .....................................................................................................................5-3

A

BOUT THE TEMPERATURE SENSORS FOR FAN SPEED SWITCHES .........................................................5-3

C

HANGING THE CHASSIS POLLING INTERVAL .........................................................................................5-4

A

DJUSTING TEMPERATURE THRESHOLDS ..............................................................................................5-4

V

IEWING FAN SPEED SWITCHES AND TEMPERATURE THRESHOLDS ........................................................5-5

D

ISPLAYING MANAGEMENT MODULE CPU USAGE .......................................................................................5-5

R

EMOVING MAC ADDRESS ENTRIES ...........................................................................................................5-5

C

HAPTER

6

M

AINTAINING

THE

H

ARDWARE

..................................................................... 6-1

HARDWARE MAINTENANCE SCHEDULE .........................................................................................................6-1

R

EPLACING A POWER SUPPLY ....................................................................................................................6-2

I

NSTALLATION PRECAUTIONS AND WARNINGS ........................................................................................6-2

D

ETERMINING WHICH POWER SUPPLY FAILED ......................................................................................6-2

AC P

OWER SUPPLIES ..........................................................................................................................6-2

DC P

OWER SUPPLIES ..........................................................................................................................6-3

V

ERIFYING PROPER OPERATION ...........................................................................................................6-5

D

ISPLAYING THE STATUS OF THE POWER SUPPLIES ..............................................................................6-5

I

NSTALLING OR REPLACING A 10-GIGABIT ETHERNET MODULE .....................................................................6-6

D

ISASSEMBLING THE CHASSIS ..............................................................................................................6-6

R

EMOVING A 10-GIGABIT ETHERNET MODULE .......................................................................................6-6

I

NSTALLING A 10-GIGABIT ETHERNET MODULE ......................................................................................6-7

R

E-ASSEMBLING THE CHASSIS ..............................................................................................................6-7

R

EPLACING A FIBER OPTIC MODULE ...........................................................................................................6-7

R

EMOVING A FIBER OPTIC MODULE ......................................................................................................6-8

I

NSTALLING A NEW FIBER OPTIC MODULE .............................................................................................6-8

C

ABLING A FIBER OPTIC MODULE .........................................................................................................6-9

C

LEANING THE FIBER-OPTIC CONNECTORS .................................................................................................6-9

C

HAPTER

7

H

ARDWARE

S

PECIFICATIONS

....................................................................... 7-1

CHASSIS SPECIFICATIONS ...........................................................................................................................7-2

P

HYSICAL DIMENSIONS .........................................................................................................................7-2

E

NVIRONMENTAL CONSIDERATIONS ......................................................................................................7-2

C

OOLING .............................................................................................................................................7-3

R

EGULATORY COMPLIANCE ..................................................................................................................7-3

W

ARRANTY ..........................................................................................................................................7-3

Foundry Hardware Installation Guide for the FES, FESX, and FWSX

vi © Foundry Networks, Inc. June 2006

PINOUTS AND SIGNALING ......................................................................................................................7-3

C

ABLE SPECIFICATIONS ........................................................................................................................7-5

P

OWER CORDS ....................................................................................................................................7-6

P

OWER SUPPLY SPECIFICATIONS ................................................................................................................7-6

O

VERVIEW ...........................................................................................................................................7-6

K

EY FEATURES .....................................................................................................................................7-7

P

HYSICAL DIMENSIONS AND WEIGHT ....................................................................................................7-7

I

NPUT CONNECTOR ..............................................................................................................................7-8

R

EGULATORY COMPLIANCE ..................................................................................................................7-8

E

NVIRONMENTAL CONSIDERATIONS ....................................................................................................7-10

E

LECTRICAL SPECIFICATIONS .............................................................................................................7-11

A

PPENDIX

8

C

AUTIONS

AND

W

ARNINGS

.......................................................................... 8-1

CAUTIONS ..................................................................................................................................................8-1

W

ARNINGS .................................................................................................................................................8-7

Chapter 1

About This Guide

Introduction

This guide describes the following product families from Foundry Networks:

• FastIron Edge Switch (FES) Layer 2/Layer 3 Switch

• FastIron Edge Switch X-Series (FESX) Layer 2/Layer 3 Switch

• FastIron Workgroup Switch X-Series (FWSX) Layer 2 Switch

This guide includes procedures for installing the hardware and configuring essential, basic parameters such as

permanent passwords and IP addresses. The basic software configuration procedures show how to perform

tasks using the CLI. This guide also includes instructions for managing and maintaining the hardware.

This guide applies to the following products, collectively called the FastIron Family of stackable switches:

• FastIron Edge Switch products:

• FastIron Edge Switch 2402

• FastIron Edge Switch 4802

• FastIron Edge Switch 9604

• FastIron Edge Switch 12GCF

• FastIron Edge Switch 2402-POE

• FastIron Edge Switch 4802-POE

• FastIron Edge Switch X-Series products:

• FastIron Edge Switch X424

• FastIron Edge Switch X448

• FastIron Edge Switch X624

• FastIron Edge Switch X648

• FastIron Workgroup Switch X-Series products:

• FastIron Workgroup Switch X424

• FastIron Workgroup Switch X448

Foundry Hardware Installation Guide for the FES, FESX, and FWSX

NOTE: Except where explicitly mentioned in this manual, the FES2402 and FES2402-POE are similar devices,

and the FES4802 and FES4802-POE are similar devices. For example, the FES2402 and FES2402-POE have

similar network interfaces and port regions. The same is true of the FES4802 and FES4802-POE.

NOTE: This guide contains the terms FastIron Edge Switch (FES), FastIron Edge Switch X-Series (FESX),

and FastIron WorkGroup Switch X-Series (FWSX). Each term refers to a specific set of devices, as shown in

Table 1.1.

What’s Included in This Edition?

This edition describes the following software releases:

• For the FastIron Edge Switch products:

• 03.3.01a

• 03.3.00

• 03.2.00

• 03.1.02

• 03.1.01

• 03.1.00

• 03.0.00

• For the FastIron Edge Switch X-Series products (not including FESX624 and FESX648):

• 02.3.03 (combined FESX/FWSX release)

• 02.3.02 (combined FESX/FWSX release)

• 02.3.01 (combined FESX/FWSX release)

• 02.2.00 (combined FESX/FWSX release)

• 02.1.01

• 02.0.00

• 01.1.00

• 01.0.00

• For the FESX624 and FESX648:

• 02.6.00

Table 1.1: FastIron Family of Switches

This Name Refers to These Devices

FastIron Edge Switch (FES) FES2402, FES4802, FES9604, FES12GCF,

FES2402-POE, and FES4802-POE

FastIron Edge Switch X-Series (FESX) FESX424, FESX448, FESX624, and FESX648

FastIron Workgroup Switch X-Series

(FWSX)

FWSX424 and FWSX448

About This Guide

• For the FastIron Workgroup Switch X-Series products:

• 02.0.00

NOTE: Software releases for the FWSX devices were combined with the FESX software releases starting

with FESX release 02.2.00.

Audience

This guide is designed for network installers, system administrators, and resellers who will install the FastIron

hardware. This guide assumes a working knowledge of Layer 2 and Layer 3 Switching and routing concepts.

Nomenclature

This guide uses the following typographical conventions to show information:

Italic highlights the title of another publication and occasionally emphasizes a word or phrase.

Bold highlights a CLI command.

Bold Italic highlights a term that is being defined.

NOTE: A note emphasizes an important fact or calls your attention to a dependency.

CAUTION: A caution calls your attention to a possible hazard that can damage equipment.

WARNING: A warning calls your attention to a possible hazard that can cause injury or death.

Related Publications

The following Foundry Networks documents supplement the information in this guide.

• Foundry FastIron X-Series Configuration Guide – for X-Series devices (FESX, FSX, and FWSX), provides

configuration procedures for system-level features, and provides configuration information for enterprise

routing protocols including IP, RIP, IP multicast, OSPF, BGP4, VRRP and VRRPE.

• Foundry Switch and Router Installation and Basic Configuration Guide – for FES devices, provides basic

configuration procedures for system-level features.

• Foundry Enterprise Configuration and Management Guide – for FES devices, provides configuration

information for enterprise routing protocols including IP, RIP, IP multicast, OSPF, VRRP and VRRPE.

• Foundry Security Guide – provides procedures for securing management access to Foundry devices and for

protecting against Denial of Service (DoS) attacks.

• Foundry Switch and Router Command Line Interface Reference – for FES devices, provides a list and syntax

information for all CLI commands on Foundry devices.

• Foundry Diagnostic Guide – provides descriptions of diagnostic commands that can help you diagnose and

solve issues on Foundry devices.

• Foundry Management Information Base Reference – contains the Simple Network Management Protocol

(SNMP) Management Information Base (MIB) objects supported on Foundry devices.

• Release Notes for the FastIron Edge Switch – describes features introduced in each software release, lists

features that are supported on the FES, and describes how configuration procedures or defaults differ from

Foundry Hardware Installation Guide for the FES, FESX, and FWSX

those on other Foundry devices, due to the FastIron Edge Switches’ hardware architecture.

• Release Notes for the FastIron Edge Switch X-Series – describes features introduced in each software

release, lists features that are supported on the FESX, and describes how configuration procedures or

defaults differ from those on other Foundry devices, due to the FastIron Edge Switch X-Series’ hardware

architecture.

• Release Notes for the FastIron Workgroup Switch X-Series – describes features introduced in each software

release, lists features that are supported on the FWSX, and describes how configuration procedures or

defaults differ from those on other Foundry devices, due to the FastIron Workgroup Switch X-Series’

hardware architecture.

How to Get Help

Foundry Networks technical support will ensure that the fast and easy access that you have come to expect from

your Foundry Networks products will be maintained.

Web Access

• http://www.foundrynetworks.com

Email Access

Technical requests can also be sent to the following email address:

• support@foundrynet.com

Telephone Access

• 1.877.TURBOCALL (887.2622) United States

• 1.408.586.1881 Outside the United States

Warranty Coverage

Contact Foundry Networks using any of the methods listed above for information about the standard and extended

warranties.

Chapter 2

Product Overview

This chapter contains an overview of the following Foundry Networks product families:

• FastIron Edge Switch® (FES) Layer 2 / Layer 3 Switch

• FastIron Edge Switch X-Series® (FESX) Layer 2 / Layer 3 Switch

• FastIron Workgroup Switch X-Series® (FWSX) Layer 2 Switch

This chapter contains the following information:

Product Overview

The FES, FESX, and FWSX deliver a full complement of standards-based, feature-rich switching and Layer 3

multiprotocol routing capabilities. The extensive feature set supports network requirements ranging from basic

connectivity to multicast-enabled full streaming audio and video applications for converged services such as Voice

over IP (VoIP).

The FES, FESX, and FWSX come in a variety of models, providing an integral range of network connectivity within

the entire enterprise network. These switches provide high 10/100 port density and Gigabit Ethernet uplinks in a

compact, stackable form factor. The FESX and FWSX optionally provide up to two 10-Gigabit Ethernet uplinks.

The FES, FESX, and FWSX models are described below.

• Standard - Provides enterprise network connectivity and server farm support at the wiring closet and edge of

the network. When first shipped from the factory, standard models support full Layer 2 and base Layer 3

Switching.

Table 2.1: Chapter Contents

Description See Page

Product overview and the benefits each product offers 2-1

Software features 2-3

POE support overview 2-3

Wireless support overview 2-3

Hardware features and how each major hardware

component functions

2-4

Foundry Hardware Installation Guide for the FES, FESX, and FWSX

NOTE: The FWSX is a Layer 2 Switch only. It does not support base Layer 3 and full Layer 3.

• Premium (PREM) – Premium devices support full Layer 2 Switching and full Layer 3 multiprotocol routing. All

FES and FESX devices can be upgraded to full Layer 3 multiprotocol routing, at which time they are

considered to be premium devices.

• 12GCF - Provides distribution and backbone connectivity at the Distribution and Core Layers of the enterprise

network. When first shipped from the factory, 12GCF models support full Layer 2 and base Layer 3

Switching.

• POE - Provides enterprise network connectivity and server farm support at the wiring closet and edge of the

network. Also provides electrical power over existing Ethernet cables, supporting the need for integrated

data, voice, and video applications. When first shipped from the factory, POE models support full Layer 2 and

base Layer 3 Switching.

• X-Series - Provides enterprise network connectivity, delivering Gigabit over Copper (GoC) to the desktop,

within the enterprise Distribution Layer, and the service provider data center for high-end servers, cluster

computing, and network-attached storage devices. Also provides the option of a one- or two-port 10 Gigabit

Ethernet module, enabling connectivity within a Metropolitan Area Network (MAN).

See Table 2.2 for a list of supported configurations.

Supported Configurations

Table 2.2 lists the FastIron stackable products and their supported configurations.

NOTE: The device numbers denote the number of ports on the device. For example, the FES2402 has 24 10/

100 ports and 2 Gigabit uplink ports. Likewise, the FESX424, FESX624, and FWSX424 have 4 Gigabit uplink

ports and 24 10/100/1000 ports.

Table 2.2: FastIron Product Family Supported Configurations

Device Standard PREM (Premium) P (POE)

FES2402 X X X

FES4802 X X X

FES9604 X X

FES12GCF X X

FESX424 X

X

a

a.FESX premium devices are available starting in software release 02.0.00.

X

b

b.The FESX424-POE is available starting in software release 02.4.00.

FESX448

X

b

X

a

FESX624 X X

FESX648 X X

FWSX424

c

c.The FWSX424 and FWSX448 devices are Layer 2 Switches only. These devices do not support

base Layer 3 and full Layer 3.

X

FWSX448

c

X

Product Overview

Software Features

Software features differ depending on the software version that is loaded on the device. When first shipped,

Standard and POE devices support full Layer 2 and base Layer 3 Switching. FWSX devices support full Layer 2

Switching only. Premium (PREM) devices support full Layer 2 Switching and full Layer 3 multiprotocol routing. All

FES and FESX devices can be upgraded to premium models, meaning all models can support full Layer 3

multiprotocol routing.

For a complete list of software features supported on the FESX or FWSX, see the release notes or the Foundry

FastIron X-Series Configuration Guide. For a complete list of software features supported on FES, see the FES

release notes.

POE Applications

Foundry’s FES2402-POE, FES4802-POE, and FESX424-POE provide Power over Ethernet, compliant with the

standards described in the IEEE 802.3af specification for delivering in-line power. The 802.3af specification

defines the standard for delivering power over existing network cabling infrastructure, enabling multicast-enabled

full streaming audio and video applications for converged services, such as, Voice over IP (VoIP), WLAN access

points, IP surveillance cameras, and other IP technology devices.

POE technology eliminates the need for an electrical outlet and dedicated UPS near IP powered devices. With

power sourcing devices, such as Foundry’s FES2402-POE and FES4802-POE, power is consolidated and

centralized in the wiring closets, improving the reliability and resiliency of the network. Because POE can provide

power over Ethernet cable, power is continuous, even in the event of a power failure.

For more information about POE and how to configure it on FES devices, see the Foundry Switch and Router

Installation and Basic Configuration Guide. For information about POE and how to configure it on FESX devices,

see the Foundry FastIron X-Series Configuration Guide.

Wireless Applications

You can convert (upgrade) your FastIron Edge Switch to an IronPoint-FES device. Converting your FES to an

IronPoint–FES allows you to run a software image that contains wireless feature support.

To convert your FES to an IronPoint-FES, you need an EEPROM kit, part number FESWLAN. The kit includes a

Dual Inline Package (DIP) key, IronPoint-FES software, upgrade instructions, and other items. Alternatively, you

can order an IronPoint-FES with the EEPROM and wireless software already installed.

You can convert the following FES devices to an IronPoint-FES:

• FastIron Edge Switch 2402

• FastIron Edge Switch 4802

• FastIron Edge Switch 9604

• FastIron Edge Switch 2402–DC

• FastIron Edge Switch 4802–DC

• FastIron Edge Switch 9402–DC

• FastIron Edge Switch 2402-POE

• FastIron Edge Switch 4802-POE

NOTE: You cannot convert the FES12GCF, FastIron Edge Switch X-Series, FastIron Workgroup Switch X-

Series, and FastIron SuperX to an IronPoint–FES device.

Foundry Hardware Installation Guide for the FES, FESX, and FWSX

The following IronPoint FES devices ship with the firmware required for the wireless features:

• FastIron Edge Switch 2402-WLAN

• FastIron Edge Switch 4802-WLAN

• FastIron Edge Switch 9604-WLAN

• FastIron Edge Switch 2402-WLAN-DC

• FastIron Edge Switch 4802-WLAN-DC

• FastIron Edge Switch 9604-WLAN-DC

• FastIron Edge Switch 2402-POE-WLAN

• FastIron Edge Switch 4802-POE-WLAN

Hardware Features

This section describes the physical characteristics of the Foundry FES, FESX, and FWSX. For details about

physical dimensions, power supply specifications, and pinouts, see the chapter “Hardware Specifications” on

page 7-1.

FES2402, FES4802, FES9604

The FastIron Edge Switch (FES) family provides high 10/100 port density and 10/100/1000 Gigabit Ethernet

uplinks in a compact form factor.

• The FES2402 has 24 10/100 ports and two Gigabit uplink ports.

• The FES4802 has 48 10/100 ports and two Gigabit uplink ports.

• The FES9604 has 96 10/100 ports and four Gigabit uplink ports.

The following figures show the front panels of these FastIron Edge Switches.

Figure 2.1 FastIron Edge Switch 2402

Figure 2.2 FastIron Edge Switch 4802

Console

PS1

PS2

Power

25C

Act

Lnk

26C

25F 26F

Lnk/

Act

Lnk/

Act

FDX

1

2

13

14

Console

PS1

PS2

Power

49C

Act

Lnk

50C

49F 50F

Lnk/

Act

Lnk/

Act

FDX

1

2

13

14

25

26

37

38

Product Overview

Figure 2.3 FastIron Edge Switch 9604

FES12GCF

The FES12GCF provides 12 combination 10/100/1000 Gigabit Ethernet Copper and Fiber ports in a compact form

factor.

Figure 2.4 shows the front panel of the FES12GCF.

Figure 2.4 FastIron Edge Switch 12GCF

FES2402-POE and FES4802-POE

• The FES2402-POE has 24 10/100 ports and two Gigabit uplink ports.

• The FES4802-POE has 48 10/100 ports and two Gigabit uplink ports.

The following figures show the front panels of these FastIron Edge Switches.

Figure 2.5 FastIron Edge Switch 2402-POE

99C

Act

Lnk

100C

99F 100F

49

50

61

62

73

74

85

86

1

2

13

14

25

26

37

38

Console

PS1

PS2

Power

97C

Act

Lnk

98C

97F 98F

Lnk/

Act

Lnk/

Act

FDX

CONSOLE

FastIron Edge 12GCF

ACT

LINK

1F 2F

1C

2C

ACT

LINK

11F 12F

11C

12C

POWER

PS1

PS2

ACT

LINK

9F 10F

9C

10C

ACT

LINK

7F 8F

7C

8C

ACT

LINK

5F 6F

5C

6C

ACT

LINK

3F 4F

3C

4C

CONSOLE

POWER

PS1

PS2

ACT

LINK

25F 26F

FastIron Edge 2402 POE

1

2

3

4

5

6

7

8

9

10

11

12

241714 15 16 18 2319 20 21 22131252 3 4 6 117 8 9 101

Link/Act

FDX

Power

13

14

15

16

17

18

19

20

21

22

23

24

25C

26C

Foundry Hardware Installation Guide for the FES, FESX, and FWSX

Figure 2.6 FastIron Edge Switch 4802-POE

FESX424, FESX624, and FWSX424

The FESX424, FESX624, and FWSX424 have the following ports:

• 24 Copper ports that support 10/100/1000Base-T RJ-45 connectors

• Four Gigabit Fiber ports for mini-GBIC optical transceivers (also called Small Form Factor Pluggable (SFP)

MultiSource Agreement (MSA)-compliant optical transceivers)

• Optionally, one or two 10-Gigabit Ethernet uplink ports for 10-Gigabit Small Form Factor Pluggable (XFP)

MSA-compliant optical transceivers

Note that one port out of the first four Copper ports or the four Fiber ports can be active at a time (see “FES 10/

100/1000 Mbps Ports” on page 2-9).

The following figure shows the front panel of the FESX424. The FESX624 and FWSX424 looks similar to the

FESX424.

Figure 2.7 FESX424

FESX424HF

The FESX424HF has the following ports:

• 20 100/1000 Gigabit Ethernet fiber ports for mini-GBIC optical transceivers (also called Small Form Factor

Pluggable (SFP) Multisource Agreement (MSA)-compliant optical transceivers).

• Four combination Gigabit Copper/Fiber uplink ports:

• The copper ports support 10/100/1000Base-T RJ-45 connectors.

• The fiber ports support 100/1000 SFPs.

• Optionally, one or two 10-Gigabit Ethernet uplink ports for 10-Gigabit Small Form Factor Pluggable (XFP)

MSA-compliant optical transceivers

Note that one port out of the first four Copper ports or the four Fiber ports can be active at a time. For example,

you can use ports 1C – 4C of the Gigabit Copper ports or ports 1 – 4 of the Gigabit Fiber ports. You can use a

combination of fiber and copper uplink ports or all copper or all fiber ports, as needed. For more information, see

see “FESX and FWSX Combination Ports” on page 2-11.

The following figure shows the front panel of the FESX424HF.

241714 15 16 18 2319 20 21 2213

CONSOLE

POWER

PS1

PS2

ACT

LINK

49F 50F

FastIron Edge 4802 POE

37

38

39

40

41

42

43

44

45

46

47

48

484138 39 40 42 4743 44 45 4637

49C

50C

25

26

27

28

29

30

31

32

33

34

35

36

362926 27 28 30 3531 32 33 3425

13

14

15

16

17

18

19

20

21

22

23

24

1

2

3

4

5

6

7

8

9

10

11

12

1252 3 4 6 117 8 9 101

Console

PS2

PS1

Power

1

2

FastIron Edge X424

1F

Lnk

Act

Lnk

Act

2F

Lnk

Act

3F

Lnk

Act

4F

Lnk

Act

1

2

3

4

1

2

5

6

1

2

7

8

9

10

11

12

115

16

117

18

13

14

19

20

21

22

23

24

Act

Lnk

25/49 26/50

Product Overview

Figure 2.8 FESX424HF Front Panel

FESX424-POE

Foundry’s FESX424-POE is new in release 02.4.00. Its 10/100/1000 ports provide Power over Ethernet (PoE),

compliant with the IEEE 802.3af specification for delivering power over the LAN. The 802.3af specification

provides the standard for delivering power over existing network cabling infrastructure, enabling multicast-enabled

full streaming audio and video applications for converged services, such as, Voice over IP (VoIP), WLAN access

points, IP surveillance cameras, and other IP powered devices.

For more information about POE and the CLI commands used to configure it, see the Foundry FastIron X-Series

Configuration Guide.

The FESX424-POE has the following ports:

• 20 10/100/1000 ports with RJ-45 copper connectors

• Four combination Gigabit Copper/Fiber uplink ports:

• The copper ports support 10/100/1000BaseT RJ-45 connectors.

• The fiber ports support 10/100/1000 SFPs.

• Optionally, one or two 10-Gigabit Ethernet uplink ports for 10-Gigabit Small Form Factor Pluggable (XFP)

MSA-compliant optical transceivers

The ports numbered from 1 – 24 support POE.

Note that one port out of the first four Copper ports or the four Fiber ports can be active at a time. For example,

you can use ports 1 – 4 of the Gigabit Copper ports or ports 1F – 4F of the Gigabit Fiber ports. You can use a

combination of fiber and copper uplink ports or all copper or all fiber ports, as needed. For more information, see

see “FESX and FWSX Combination Ports” on page 2-11.

The following figure shows the front panel of the FESX424-POE.

Figure 2.9 FESX424-POE Front Panel

FESX448, FESX648, and FWSX448

The FESX448, FESX648, and FWSX448 have the following ports:

• 48 Copper ports that support 10/100/1000Base-T RJ-45 connectors

• Four Gigabit Fiber uplink ports (1F – 4F) for mini-GBIC optical transceivers (also called Small Form Factor

Pluggable (SFP) Multisource Agreement (MSA)-compliant optical transceivers)

Console

PS2

PS1

Power

FastIron Edge X424HF

Lnk/Act

1C 2C 3C 4C

Act

Lnk

25/49 26/50

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

Lnk/Act

Console

PS2

PS1

Power

FastIron

on

Edge X424-POE

1F 2F 3F

Lnk Act Lnk Act Lnk Act Lnk Act

4F

Act

Lnk

25/49 26/50

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

Lnk/

Act

POE Power

Lnk/

Act

Foundry Hardware Installation Guide for the FES, FESX, and FWSX

• Optionally, one or two 10-Gigabit Ethernet uplink ports for 10-Gigabit Small Form Factor Pluggable (XFP)

MSA-compliant optical transceivers

Note that one port out of the first four Copper ports or the four Fiber ports can be active at a time (see “FES 10/

100/1000 Mbps Ports” on page 2-9). For example, you can use ports 1 –4 of the Gigabit Copper ports or ports 1F

– 4F of the Gigabit Fiber ports. You can use a combination of fiber and copper ports or all copper or all fiber ports,

as needed.

The following figure shows the front panel of the FESX448. The FESX648 and FWSX448 looks similar to the

FESX448.

Figure 2.10 FESX448 Front Panel

Control Features

Each device’s front panel has the following control features:

• Serial management interface (the port labeled Console)

• Reset button

• 10/100 ports with RJ-45 copper connectors (FES only)

• 10/100/1000 ports with RJ-45 copper connectors

• 10/100/1000 ports with mini-GBIC slots for SFP MSA-compliant fiber transceivers

• 100/1000 ports with mini-GBIC slots for SFP MSA-compliant fiber transceivers (FESX424HF)

• Optionally, one or two 10 Gigabit Ethernet ports for XFP MSA-compliant fiber connector(s) (FESX and FWSX

only)

Serial Management Interface (Console Port)

The serial management interface enables you to configure and manage the device using a third-party terminal

emulation application on a directly connected PC. A straight-through EIA/TIA DB-9 serial cable (M/F) ships with

the device. The serial management interface (the port labeled Console) is located in the left corner of the front

panel.

Reset Button

The reset button allows you to restart the system without switching the power supplies off and on or using the CLI

or Web management interface. The button is located to the right of the serial management interface and is

recessed to prevent it from being pushed accidentally.

FES Network Interfaces

The FES2402, 4802, and 9604 provide the following interfaces:

• 10Base-T/100Base-T (10/100) copper ports

• 10/100/1000Base-T copper or Fiber Gigabit uplink ports

The FES12GCF provides the following interfaces:

• 10/100/1000Base-T copper or Fiber Gigabit uplink ports

For information about the type of fiber optic modules supported on FES devices, see “Fiber Optic Modules” on

page 2-15.

Console

PS2

PS1

Power

1

2

FastIron Edge X448

1F

Lnk

Act

Lnk

Act

2F

Lnk

Act

3F

Lnk

Act

4F

Lnk

Act

1

2

3

4

1

2

5

6

1

2

7

8

9

10

11

12

15

16

17

18

19

20

21

22

23

24

Act

Lnk

25/49 26/50

13

14

25

26

31

3230

27

28

29

33

34

35

36

37

38

39

40

41

42

47

4846

43

44

45

Product Overview

FES 10/100 Mbps Ports

The 10/100 copper ports support automatic MDI/MDIX detection, and use auto-sensing and auto-negotiating to

determine the speed (10 Mbps or 100 Mbps) and mode (full-duplex or half-duplex) of the port at the other end of

the link and adjust port speed accordingly. In addition, the 10/100 ports on the FES POE models can detect

802.3af compatible IP devices and provide power accordingly.

For more information about automatic MDI/MDIX detection, see the Foundry Switch and Router Installation and

Basic Configuration Guide.

The 10/100 ports use RJ-45 connectors. For pinout information, see the chapter “Hardware Specifications” on

page 7-1".

The 10/100 Mbps ports on FES devices provide status information using the LEDs listed in Table 2.3.

FES 10/100/1000 Mbps Ports

The 10/100/1000 ports use auto-sensing and auto-negotiating to determine the speed (10 Mbps, 100 Mbps, or

1000 Mbps) and mode (full-duplex or half-duplex) of the port at the other end of the link and adjust port speed

accordingly. 10/100/1000 ports on the devices have the following interfaces:

• RJ-45 copper interface for 10/100/1000Base-T – Cat5 copper cabling

• Mini-GBIC slot for CWDM, 1000Base-BX, LH, LX, or SX – fiber cabling

The copper ports provide auto MDI/MDIX detection (see the Foundry Switch and Router Installation and Basic

Configuration Guide).

One port out of each pair of copper and fiber ports can be active at a time. For example, on the FES12GCF, you

can use either Copper port 10 or Fiber port 10, but not both at the same time. You can use a combination of fiber

and copper ports or all copper or all fiber ports, as needed. On the FES, if you attach both the copper and fiber

connectors for a port to the network, the fiber connector takes precedence over the copper connector and will be

the active connector for the port. Insertion of a fiber mini-GBIC disables the copper connector. To enable a port’s

copper connector, you must remove the port’s fiber mini-GBIC.

The 10/100/1000 Mbps ports on the FES provide status information using the LEDs listed in Table 2.3. The fiber

connectors on the FES devices use the Lnk and Act LEDs located between the mini-GBIC slots for the fiber ports.

The copper connectors use triangular LEDs located in the upper right and left corners of the upper Gigabit copper

connector. The LED on the left side is for the upper copper connector. The LED on the right side is for the lower

copper connector.

Foundry Hardware Installation Guide for the FES, FESX, and FWSX

LEDs for FES Ports

The 10/100 Mbps and 10/100/1000 Mbps ports on FES devices provide status information using the LEDs listed in

Table 2.3.

Table 2.3: LEDs for FES Ports

LED Position State Meaning

10/100 Port LEDs

Lnk/Act Left LED above

port

OR

Top LED above

port

On Link is up.

Off Link is down.

Blinking Port is transmitting or receiving.

FDX Right LED

above port

OR

Middle LED

above port

On Full-duplex connection found or

configured.

Off Half-duplex connection or no port

connection exists.

Blinking Collisions are being detected.

Power (POE

devices only)

Bottom LED

above port

(POE devices

only)

On The port is providing in-line power to the

power consuming device, such as a VoIP

phone or other device, that is connected

to the port.

Off The port is not providing in-line power.

10/100/1000 Port LEDs

Lnk/Act Top On Link is up.

Off Link is down.

Blinking Port is transmitting or receiving traffic

FDX Bottom On Full-duplex connection found or

configured.

Note: This LED also is lit if you configure

the port to 10 Mbps full-duplex or 100

Mbps full-duplex. This is true even when

no link is present.

Off Half-duplex connection or no port

connection exists.

Blinking Collisions are being detected.

Upper left

corner of upper

copper

connector for

upper copper

connector

Off No copper port connection exists on

upper copper connector.

Green Copper port is connected on upper copper

connector.

Amber Traffic is being transmitted and received

on upper copper connector.

La page charge ...

Foundry Networks FES12GCF Guide d'installation

Foundry Networks FES12GCF Guide d'installation

dans d''autres langues

Autres documents