Drolet ECO-55 ST PELLET STOVE Guide d'installation

INSTALLATION MANUAL

ECO-55 / ECO-55 CT / ECO-55 ST

(DP00070, DP00072 & DP00071 model)

Safety tested according to ULC S627,UL1482 and

ASTM E1509 by an accredited laboratory

INSTALLATION BY A PROFESSIONAL

IS STRONGLY RECOMMENDED

Stove Builder International inc.

250, rue de Copenhague,

St-Augustin-de-Desmaures (Québec) Canada

G3A 2H3

Customer service : 418-908-8002

Email : [email protected]

www.drolet.ca

CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION

INSPECTION REQUIREMENTS IN YOUR AREA.

PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET FUEL-

BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN

PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH.

READ AND KEEP THIS MANUAL FOR REFERENCE

This manual is available for free download on the manufacturer’s website. It is a copyrighted document. Re-sale

is strictly prohibited. The manufacturer may update this manual from time to time and cannot be responsible

for problems, injuries, or damages arising out of the use of information contained in any manual obtained from

unauthorized sources.

Printed in Canada

45876IA

2020-12-08

ENGLISHFRANÇAIS

25 1/4"

640mm

22 7/8"

581mm

24 7/8"

632mm

29 1/2"

750mm

23 7/8"

607mm

24 7/8"

633mm

8 5/8"

218mm

17 3/8"

441mm

32 5/8"

829mm

O

3"

76mm

O

3"

76mm

11 3/8"

290mm

6 1/8"

155mm

A

B

A

B

15 3/4"

401mm

8 1/8"

205mm

Page 2 INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

1. SAFETY INFORMATION

We highly recommend that our pellet burning hearth

products be installed and serviced by professionals

who are certied in the United States by NFI (National

Fireplace Institute ® ) or in Canada by WETT (Wood

Energy Technology Transfer) or in Quebec by APC

(Association des Professionnels du Chauage).

If this appliance is not properly installed,

combustible materials near it may overheat. To

reduce the risk of re, follow the installation

instructions in this manual exactly. Contact local

building or re ocials about restrictions and

installation inspection requirements in your area.

Please read this entire manual before you install and

use your new stove. You may need to get a building

permit for the installation of this appliance and the

venting system that it is connected to. Consult your

municipal building department or re department

before installation. We recommend that you also

inform your home insurance company to nd out if

the installation will aect your policy.

WARNING

IF THIS STOVE IS NOT PROPERLY INSTALLED,

A HOUSE FIRE MAY RESULT. TO REDUCE THE

RISK OF FIRE, FOLLOW THE INSTALLATION

INSTRUCTIONS.

NOTICE

The information given on the certication label

axed to the stove always overrides the information

published in any other media (owner’s manual,

catalogues, yers, magazines or web sites).

BURNING ANY SOLID FUELS GENERATES

CARBON MONOXIDE IN LOW

CONCENTRATION. THIS GAS IS EVACUATED

BY THE EXHAUST VENTING SYSTEM. IN

HIGHER CONCENTRATIONS, CARBON

MONOXIDE IS TOXIC AND MAY CAUSE DEATH.

TO PREVENT THIS, ENSURE THAT YOUR

EXHAUST VENTING SYSTEM IS AIRTIGHT.

WARNING

THIS STOVE IS NOT RECOMMENDED TO BE

INSTALLED IN A BEDROOM.

CAUTION

THIS STOVE MUST BE CONNECTED TO

A STANDARD 120V / 60HZ, GROUNDED

ELECTRICAL OUTLET. DO NOT USE AN

ADAPTER PLUG OR SEVER THE GROUNDING

PLUG. DO NOT ROUTE THE ELECTRICAL

CORD UNDERNEATH, IN FRONT OR OVER THE

STOVE.

WARNING

THIS STOVE IS MOBILE HOME APPROVED

AND REQUIRES INSTALLATION OF A FRESH

AIR KIT, SOLD SEPARATELY. THE STOVE

MUST BE ATTACHED TO THE STRUCTURE OF

THE MOBILE HOME AND THE STRUCTURAL

INTEGRITY OF THE MOBILE HOME FLOOR,

WALL, AND CEILING / ROOF MUST BE

MAINTAINED. DO NOT INSTALL IN A SLEEPING

ROOM.

NOTICE

Mixing of appliance components from dierent

sources or modifying components is prohibited

and will void the warranty. Any modication of the

appliance that has not been approved in writing by

the testing authority is prohibited and violates CSA

B365 (Canada) and NFPA 211 (USA).

WARNING

NOTICE

When locating your appliance, make sure the vent

will not interfere with any truss, roof beams, wall

studs, water pipes or electrical wiring. It may be

easier to relocate appliance than to rework the

building structure.

Page 3

INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

NOTICE

This stove has been developed and built for

residential supplementary heat source. Commercial

and industrial use is prohibited and will void the

warranty.

NOTICE

Stove Builder International inc. (SBI) grants no

warranty, implied or stated, for the poor installation

of your appliance and assumes no responsibility of

any consequential damages.

This product can expose you

to chemicals including carbon

monoxide, which is known to the

State of California to cause cancer,

birth defects or other reproductive

harm. For more information go to

www.P65warnings.ca.gov/

Page 4 INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

TABLE OF CONTENTS

1. SAFETY INFORMATION ...............................................................................2

2. GENERAL FEATURES .................................................................................. 5

2.1 OVERALL DIMENSIONS (DP00070-DP00072) ...............................................................5

2.2 OVERALL DIMENSIONS (DP00071) ................................................................................6

3. CLEARANCES TO COMBUSTIBLE MATERIALS ......................................7

3.1 CLEARANCES TO COMBUSTIBLES MATERIALS, WALLS AND CEILING ...............7

3.2 FLOOR PROTECTION ......................................................................................................8

4. VENTING SYSTEM ........................................................................................ 9

4.1 GENERAL ...........................................................................................................................9

4.2 RECOMMANDATIONS ......................................................................................................9

4.3 EQUIVALENT VENT LENGTH (EVL) ...............................................................................9

4.3.1 RECOMMENDED EXHAUST VENTING DIAMETER .......................................................9

4.3.2 INSTALLATION COMPLIANCE ....................................................................................... 10

4.4 TERMINATION LOCATION .............................................................................................11

4.5 DIRECT VENT SYSTEM ................................................................................................12

4.6 INSTALLATION CONFIGURATION ...............................................................................12

4.6.1 THROUGH WALL INSTALLATION (MAIN FLOOR OR BASEMENT) ............................. 12

4.6.2 THROUGH ROOF INSTALLATION .................................................................................12

4.6.3 THROUGH A FACTORY BUILT CHIMNEY .................................................................13

4.6.4 THROUGH AN EXISTING MASONRY FIREPLACE .................................................. 13

4.6.5 THROUGH AN EXISTING MASONRY CHIMNEY ......................................................14

5. INSTALLING THE OPTIONAL HOPPER EXTENSION ............................14

6. MOBILE HOME INSTALLATION ................................................................ 15

7. INSTALLING A THERMOSTAT ................................................................... 15

7.1 THERMOSTAT LOCATION .............................................................................................15

7.2 WIRED THERMOSTAT ....................................................................................................16

7.3 WIRELESS THERMOSTAT .............................................................................................16

8. COMBUSTION AIR SUPPLY ...................................................................... 16

8.1 SOURCES OF OUTSIDE COMBUSTION AIR ..............................................................17

9. APPLIANCE SET-UP ...................................................................................18

9.1 GENERAL .........................................................................................................................18

10. WIRING DIAGRAM ....................................................................................19

11. EXPLODED VIEWS AND PARTS LIST DP00070 AND DP00071 .......... 20

Page 5

INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

2. GENERAL FEATURES

Recommended

chimney diameter

3 in. (75mm)

Flue outlet diameter 3 in. (75mm)

Type of chimney ULC/ORD-C441

CAN/ULC S609

UL 641 (TYPE L)

Approved for alcove

installation

Yes

Approved for mobile

home installation ‡

Yes

Shipping weight

(without option)

277 lb (DP00070-

DP00072)

286 lb (DP00071)

Appliance weight

(without option)

235 lb (DP00070-

DP00072)

242 lb (DP00071)

Particulate emission

standard

CSA B415.1-10

ASTM E2779

USA standard (safety) ASTM E1509

UL 1482

Canadian standard

(safety)

ULC S627

Electrical

requirements

Voltage and frequency

120VAC and 60Hz

Ignition : 3.02A

‡ Mobile home (Canada) or manufactured home (USA): The

US department of Housing and Urban Development describes

“manufactured homes” better known as “mobile homes” as

followed; buildings built on xed wheels and those transported on

temporary wheels/axles and set on a permanent foundation. In

Canada, a mobile home is a dwelling for which the manufacture

and assembly of each component is completed or substantially

completed prior to being moved to a site for installation on

a foundation and connection to service facilities and which

conforms to the CAN/CSA-Z240 MH standard.

2.1 OVERALL DIMENSIONS (DP00070-

DP00072)

A FRESH AIR INLET

B FLUE OUTLET

25 1/4"

640mm

22 7/8"

581mm

24 7/8"

632mm

29 1/2"

750mm

23 7/8"

607mm

24 7/8"

633mm

8 5/8"

218mm

17 3/8"

441mm

32 5/8"

829mm

O

3"

76mm

O

3"

76mm

11 3/8"

290mm

6 1/8"

155mm

A

B

A

B

15 3/4"

401mm

8 1/8"

205mm

25 1/4"

640mm

22 7/8"

581mm

24 7/8"

632mm

29 1/2"

750mm

23 7/8"

607mm

24 7/8"

633mm

8 5/8"

218mm

17 3/8"

441mm

32 5/8"

829mm

O

3"

76mm

O

3"

76mm

11 3/8"

290mm

6 1/8"

155mm

A

B

A

B

15 3/4"

401mm

8 1/8"

205mm

25 1/4"

640mm

22 7/8"

581mm

24 7/8"

632mm

29 1/2"

750mm

23 7/8"

607mm

24 7/8"

633mm

8 5/8"

218mm

17 3/8"

441mm

32 5/8"

829mm

O

3"

76mm

O

3"

76mm

11 3/8"

290mm

6 1/8"

155mm

A

B

A

B

15 3/4"

401mm

8 1/8"

205mm

25 1/4"

640mm

22 7/8"

581mm

24 7/8"

632mm

29 1/2"

750mm

23 7/8"

607mm

24 7/8"

633mm

8 5/8"

218mm

17 3/8"

441mm

32 5/8"

829mm

O

3"

76mm

O

3"

76mm

11 3/8"

290mm

6 1/8"

155mm

A

B

A

B

15 3/4"

401mm

8 1/8"

205mm

Page 6 INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

2.2 OVERALL DIMENSIONS (DP00071)

A FRESH AIR INLET

B FLUE OUTLET

2.3 REGULATIONS COVERING PELLET

STOVE INSTALLATION

When installed and operated as described in these

instructions, this pellet stove is suitable for use as a

freestanding heater in residential installations.

In Canada, the CSA B365 Installation Code for Solid

Fuel Burning Appliances and Equipment and the CSA

C22.1 Canadian National Electrical Code are to be

followed in the absence of local code requirements.

In the USA, the ANSI NFPA 211 Standard for

Chimneys, Fireplaces, Vents and Solid Fuel-Burning

Appliances and the ANSI NFPA 70 National Electrical

Code are to be followed in the absence of local code

requirements.

This stove must be connected to a pellet vent system

complying with the requirements for Pellet Vent in the

standards UL 103, UL 641, ULC S629M, CAN/ULC

S609 and ULC/ORD C441 or to a code-approved

masonry chimney with a stainless steel ue liner.

CAUTION

DO NOT USE MAKESHIFT MATERIALS OR

MAKE ANY COMPROMISES WHEN INSTALLING

THIS STOVE.

2.4 CERTIFICATION LABEL LOCATION

Since the information given on the certication

label axed to the stove always overrides the

information published in any other media (owner’s

manual, catalogues, yers, magazines or web sites),

it is important to refer to it in order to have a safe

and compliant installation. In addition, you will nd

important information about your stove (model, serial

number, etc.). You will nd the certication label on

the inner side of the hopper lid of the stove.

23 7/8"

607mm

24 7/8"

633mm

8 5/8"

218mm

17 1/4"

439mm

36 1/8"

918mm

25 1/8"

639mm

22 7/8"

581mm

8 1/8"

205mm

15 3/4"

401mm

24 7/8"

632mm

29 1/2"

750mm

A

B

A

B

O

3"

76mm

O

3"

76mm

11 3/8"

290mm

6 1/8"

155mm

23 7/8"

607mm

24 7/8"

633mm

8 5/8"

218mm

17 1/4"

439mm

36 1/8"

918mm

25 1/8"

639mm

22 7/8"

581mm

8 1/8"

205mm

15 3/4"

401mm

24 7/8"

632mm

29 1/2"

750mm

A

B

A

B

O

3"

76mm

O

3"

76mm

11 3/8"

290mm

6 1/8"

155mm

23 7/8"

607mm

24 7/8"

633mm

8 5/8"

218mm

17 1/4"

439mm

36 1/8"

918mm

25 1/8"

639mm

22 7/8"

581mm

8 1/8"

205mm

15 3/4"

401mm

24 7/8"

632mm

29 1/2"

750mm

A

B

A

B

O

3"

76mm

O

3"

76mm

11 3/8"

290mm

6 1/8"

155mm

23 7/8"

607mm

24 7/8"

633mm

8 5/8"

218mm

17 1/4"

439mm

36 1/8"

918mm

25 1/8"

639mm

22 7/8"

581mm

8 1/8"

205mm

15 3/4"

401mm

24 7/8"

632mm

29 1/2"

750mm

A

B

A

B

O

3"

76mm

O

3"

76mm

11 3/8"

290mm

6 1/8"

155mm

Page 7

INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

3. CLEARANCES TO COMBUSTIBLE

MATERIALS

The clearances shown in this section applies to

DP00070, DP00072 and DP00071.

The clearances shown in this section have been

determined by tests according to procedures set out in

safety standards ULC S627 (Canada), ASTM E1509

(U.S.A) and UL1482 (U.S.A.). When the pellet stove

is installed so that its surfaces are at, or beyond, the

minimum clearances specied, combustible surfaces

will not overheat under normal and even abnormal

operating conditions.

WARNING

NO PART OF THE PELLET VENT SYSTEM MAY

BE LOCATED CLOSER TO COMBUSTIBLES

THAN THE MINIMUM CLEARANCES SPECIFIED

BY THE VENT MANUFACTURER.

WARNING

NO PART OF THE STOVE MAY BE LOCATED

CLOSER TO COMBUSTIBLES THAN THE

MINIMUM CLEARANCES SPECIFIED ON THE

CERTIFICATION LABEL.

NOTICE

The following clearances are also valid for an

alcove installation. However, if the stove is

installed in an alcove, to perform maintenance, you

should expect to move the appliance to get to the

maintenance access doors and components.

3.1 CLEARANCES TO COMBUSTIBLES

MATERIALS, WALLS AND CEILING

MINIMUM CLEARANCES

CANADA USA

A*

3" (76 mm) 3" (76 mm)

D

Note 1 Note 1

I**

48" (1 220 mm) 48" (1 220 mm)

*From the rear panel

**Measured from the platform on which the product is installed.

RECOMMENDED CLEARANCES FOR

MAINTENANCE

CANADA USA

A*

12" (305 mm) 12" (305 mm)

MINIMUM CLEARANCES

CANADA USA

B

6" (152 mm) 6" (152 mm)

D

Note 1 Note 1

RECOMMENDED CLEARANCES FOR

MAINTENANCE

CANADA USA

B

24" (610 mm) 24" (610 mm)

Note 1 : Refer to the exhaust venting system manufacturer’s

instructions for clearances to combustible materials.

Page 8 INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

3.2 FLOOR PROTECTION

MINIMUM CLEARANCES

CANADA USA

C

3" (76 mm) 3" (76 mm)

D

Note 1 Note 1

RECOMMENDED CLEARANCES FOR

MAINTENANCE

CANADA USA

C

12" (305 mm) 12" (305 mm)

D

Note 1 Note 1

Note 1 : Refer to the exhaust venting system manufacturer’s

instructions for clearances to combustible materials.

FLOOR PROTECTION

CANADA** USA

E

6" (152 mm)

From door opening

6" (152 mm)

From door opening

F

6" (152 mm)

From door opening

6" (152 mm)

From door opening

CAUTION

THE STOVE MUST BE PLACED ON

A CONTINUOUS (GROUTED JOINTS)

NONCOMBUSTIBLE MATERIAL SUCH AS

CERAMIC TILE*, CEMENT BOARD, BRICK,

MILLBOARD OR EQUIVALENT, OR ANY OTHER

APPROVED OR LISTED MATERIAL SUITED

FOR FLOOR PROTECTION.

*Any type of tile will require a continuous non combustible sheet

beneath to prevent the possibility of embers falling through to the

combustible oor if cracks or separation should occur in the ni-

shed surface, this would include oor protection for built-in raised

hearths. Check local codes for approved alternatives.

**You may reduce the oor protection requirements to the values

shown in the previous table ONLY if the following actions are

respected: Allow for the appliance to shut-down and re to

be extinguished. Once completely cool and all blowers have

stopped you may proceed with opening the rebox or ash door.

Otherwise, see CSA B365.

Page 9

INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

4. VENTING SYSTEM

CAUTION

CONNECT THIS STOVE ONLY TO A LISTED

PELLET EXHAUST VENTING SYSTEM FOR USE

WITH SOLID FUEL OR TO A LINED CHIMNEY

CONFORMING TO NATIONAL AND LOCAL

BUILDING CODES.

CAUTION

DO NOT CONNECT THIS STOVE TO ANY

OTHER EXISTING VENTING SYSTEM SERVING

ANOTHER APPLIANCE.

CAUTION

THE VENTING SYSTEM MUST BE COMPLETELY

AIRTIGHT AND PROPERLY INSTALLED.

ALL VENT CONNECTOR JOINTS MUST BE

SEALED AND FASTENED IN ACCORDANCE

WITH THE PELLET VENT MANUFACTURER’S

INSTRUCTIONS TO ENSURE CONSISTENT

PERFORMANCE AND AVOID SMOKE AND ASH

SPILLAGE..

CAUTION

DO NOT INSTALL A FLUE DAMPER IN THE

EXHAUST VENTING SYSTEM OF THIS UNIT.

CAUTION

DO NOT CONNECT TO OR USE IN

CONJUNCTION WITH ANY AIR DISTRIBUTION

DUCTWORK.

CAUTION

THE VENTING SYSTEM SHOULD BE CHECKED,

AT LEAST TWICE A YEAR FOR ANY BUILDUP

OF SOOT OR CREOSOTE.

4.1 GENERAL

Even though the chimney draft is mechanical, a sui-

table venting system will ensure a natural draft which

will prevent smoke spillage in your home if a power

outage occurs. Moreover, a suitable venting system

conguration will help getting the best eciency out

of your stove when installed in accordance with the

required EVL.

4.2 RECOMMANDATIONS

In Canada, we recommend that you use a listed pel-

let vent that meets the CAN/ULC S609 or ULC/ORD

C441 Standard. A pellet vent listed to ULC S629M is

also suitable for installation with this stove.

For the United States, we recommend that you use a

listed pellet vent that meets the UL 641 Standard. A

pellet vent listed to UL 103 is also suitable for instal-

lation with this stove.

This stove can be vented in an existing factory-built

or masonry chimney with the addition of a stainless

steel liner, provided the chimney is more than 4" in

diameter. The liner should be listed and should meet

the ULC S635 CAN/ULC S640 standard in Canada

and the UL 1777 standard in the USA. Refer to the

instructions provided by the vent manufacturer,

especially when passing through a wall, ceiling or

roof.

The recommended venting system inner pipe diame-

ter is 3". Use a 4" pipe if you have more than 15 feet

of Equivalent Vent Length (EVL).

To calculate the Equivalent Vent Length of your ins-

tallation, use the following conversions:

Qty Type of pipe

Equivalent vent

length (EVL)

1 90° elbow or ‘‘Tee’’ 5 feet

1 45° elbow 3 feet

1 foot horizontal pipe run 1 foot

1 foot vertical pipe run 1/2 foot

4.3 EQUIVALENT VENT LENGTH (EVL)

4.3.1 RECOMMENDED EXHAUST VENTING

DIAMETER

Page 10 INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

Here is an example to help you calculate Equivalent

Vent Length. On the following gure the EVL can be

calculated like this:

2 feet of horizontal run (2 X 1' EVL) = 2' of EVL

90° elbow or "Tee" (1 X 5' EVL) =5' of EVL

12 feet of vertical run

(12' X 0.5' EVL)

= 6’ of EVL

Termination cap = 0' of EVL

Total EVL = 13' of EVL

Since the total EVL is less than 15 feet, the re-

commended exhaust venting diameter is 3".

4.3.2 INSTALLATION COMPLIANCE

To determine if your installation is compliant, the

exhaust venting system must end within the grid on

the venting system chart. The previous installation

has 2 feet of horizontal run and 12 feet of vertical

run. It is thus standard since the venting system ends

in the gridded area.

CAUTION

• Horizontal runs shall not exceed 9 feet.

• Never exceed 30 feet of evl.

CAUTION

TO REDUCE THE RISK OF SMOKE SPILLAGE

THERE SHOULD ALWAYS BE AT LEAST ONE

FOOT OF VERTICAL RISE FOR EACH FOOT OF

HORIZONTAL RUN. IN ALL CASES, AT LEAST 3

FEET OF VERTICAL RISE IS NEEDED.

WARNING

TERMINATION OF A SIDE WALL VENT SHOULD

BE LOCATED TO AVOID PERSONAL BURN

INJURY, FIRE HAZARD AND INTERFERENCE

WITH OR DAMAGE TO ADJACENT

PROPERTIES. EXHAUST GASES CAN REACH

TEMPERATURES OF 500°F (260°C) AND CAUSE

SERIOUS BURNS.

WARNING

TERMINATION COLLAR (SPARK ARRESTER)

IS MANDATORY AND MUST BE CLEAR OF ANY

DEBRIS AT ALL TIME.

Page 11

INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

CANADA

Refer to NFPA 211 (USA) or CSA B365 (Canada) for rules for the distance of exit terminal from windows and

openings. The exit terminal of a mechanical draft system, other than a direct vent appliance shall be located

in accordance with the following.

v

A

J

B

L

B

I

A

K

F

VENT TERMINAL

SORTIE DU TUYAU D’EVACUATION

V

AIR SUPPLY INLET

ENTRÉE D’AIR FRAIS

A

AREA WHERE TERMINAL IS NOT PERMITTED

ZONE OU LA SORTIE N’EST PAS PERMISE

V

H

F

Min.

Clearances

Description

A 12" (30 cm) Clearances above grade level or any adjacent surface that might support snow, ice,

or debris.

B 39" (100 cm) Clearance to window or door that may be opened.

F 39" (100 cm) Clearance to corner or adjacent wall or any combustible materials.

H 39" (100 cm) Not to be installed above a meter/regulator assembly within 39" (100 cm) horizontally

from the vertical center-line of the regulator and for 15’ vertically.

I 72" (183 cm) Clearance to gas service regulator vent outlet or within 39’’ (100 cm) of an oil tank vent

or an oil tank ll inlet.

J 39" (100 cm) Clearance to the combustion air inlet to any other appliance.

K 72" (183 cm) Clearance to a mechanical air supply inlet.

L 84" (213 cm) Clearance above paved side-walk or a paved driveway located on public property.

39" (100 cm) Clearance to property boundary.

A vent shall not terminate underneath a veranda, porch, or deck.

A vent shall not terminate directly above a sidewalk or a paved driveway which is lo-

cated between two single family dwelling and serves both dwellings.

United-States

• Not Less than 36" (91 cm) above any forced air inlet located within 120" (305 cm);

• Not Less than 48" (122 cm) below and horizontally from, or 12" (30 cm) above, any door, window or gravity

air inlet into any building;

• Not Less than 24" (61 cm) from an adjacent building and not less than 84" (213 cm) above grade when

located adjacent to a public walkway;

• Cannot be located less than 12" (30 cm) above grade;

• Cannot be located above a gas meter/regulator within 36" (91cm) horizontally of the vertical center line of

the regulator;

• Not within 6 feet (183 cm) of a gas service regulator vent outlet;

• Other restrictions may apply. See NFPA 211 for further information.

4.4 TERMINATION LOCATION

Page 12 INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

In Canada: The permitted termination locations for a

direct vent system are the same than those permitted

with a regular pellet vent system.

In the Unites States : The permitted termination

location for a direct vent system are the same than

those permitted with a regular pellet vent system

except for the following : The exit terminal shall be

located not less than 9" (23 cm) from any opening

through which vent gases could enter a building.

4.5 DIRECT VENT SYSTEM

4.6 INSTALLATION CONFIGURATION

4.6.1 THROUGH WALL INSTALLATION (MAIN

FLOOR OR BASEMENT)

1. Position appliance following clearances vent

manufacturer’s instructions.

2. Install a stove adapter or a stove adapter tee onto

the appliance ue collar.

3. Locate the position of the exhaust pipe in the wall

and cut a hole of the appropriate size for vent in

the wall.

4. Install wall thimble as per vent manufacturer’s

instructions.

5. Ensure you install enough horizontal pipe length

to exceed the exterior wall of 6 inches. Install a

tee section to the pipe passing through the wall.

6. Run the vent vertically up the wall for at least

36". Refer to the vent manufacturer’s instructions

for clearances to combustible materials and

installation of wall bands.

7. Install a 90 degrees elbow facing out from the

wall and then attach a 45 degree elbow facing

towards the ground. The termination of the vent

must include a spark arrester, fastened to the 45

degrees elbow.

8. Sealed outside wall thimbles with high

temperature waterproof silicone sealant.

4.6.2 THROUGH ROOF INSTALLATION

1. Position appliance following clearances and

following vent manufacturer’s instructions.

2. Install a stove adapter or a stove adapter tee

onto the appliance ue collar. If necessary, use

a horizontal additional length between the ue

outlet and the tee.

3. Drop the plumb line over the center of the tee

outlet and mark location on the ceiling.

4. Cut a hole for appropriate ceiling support. Frame

rough opening.

5. Install ceiling support and the rst vent section as

per vent manufacturer’s instructions.

6. Install a restop radiation shield on any

subsequent ceiling/oor, except for the attic

where an attic insulation shield is required.

7. Run the necessary section of vent vertically so

the rain cap exceeds the highest point of the roof

at least 24" in United States and at least 36" in

Canada.

8. Install roof support.

9. Install roof ashing and rain cap as per

manufacturer’s instructions. If necessary, install

a storm collar.

Page 13

INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

4.6.3 THROUGH A FACTORY BUILT CHIMNEY

1. Position stove following clearances given and fol-

lowing vent manufacturer’s instructions.

2. Install a stove adapter or a stove adapter tee onto

the appliance ue collar. If necessary, use a ho-

rizontal additional length between the ue outlet

and the tee.

3. Use a proper chimney adaptor for your installa-

tion.

4. Run the number of sections of vent necessary to

go through the chimney adaptor into the chimney.

5. Connect the vent to a stainless steel 4" liner ac-

cording to the vent manufacturer’s instruction.

6. Install roof ashing and rain cap as per

manufacturer’s instructions. If necessary, install

and seal a storm collar.

NOTICE

Before installation, the chimney must be cleaned

and inspected by a qualied chimney sweep or

installer.

NOTICE

In the USA., the use of a stainless steel liner is

mandatory. In Canada, it is not mandatory but is

strongly recommended.

4.6.4 THROUGH AN EXISTING MASONRY

FIREPLACE

NOTICE

The structural condition of the masonry chimney

must rst be inspected by a qualied chimney

sweep or installer. You will need a pipe length

equal to the chimney height from the hearth. If

outside combustion air is to be used, you will need

a pipe length superior from 12 to 18 inches (30 to

46 cm) of the chimney height to ensure a proper

stove behaviour.

1. Position stove, following clearances and fol-

lowing vent manufacturer’s instructions.

2. Build and Install a blocking plate inside the chim-

ney to seal the replace damper. Stainless steel

plate and screws are recommended. Cut a hole

for the exhaust pipe. If needed, cut a second hole

for the air intake pipe

3. Attach a section of pipe and clean out tee to the

ue outlet, making sure the clean out tee is cen-

tered in the chimney ue area.

4. Install a vented ashing at the top of the replace

chimney. Stainless steel plate and screws are

recommended. Cut a hole for the vent pipe. If

needed, cut a second hole for the air intake pipe.

Seal all joints with high temperature waterproof

silicone sealant to prevent water leakage.

5. Seal and install vertical roof vent. If required, seal

and install a storm collar.

Page 14 INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

4.6.5 THROUGH AN EXISTING MASONRY

CHIMNEY

1. Position stove following clearances following vent

manufacturer’s instructions.

2. Mark the center of the hole where the vent pipe

will go through the masonry chimney.

3. It is necessary to make a hole in the masonry

with a one-inch diameter greater than the diame-

ter of the vent pipe used.

4. Install the cleanout tee at the bottom of the ver-

tical vent system and lower it down the chimney

until the center branch of the tee is aligned with

the hole in the masonry.

5. Connect the horizontal vent pipe to the cleanout

tee by pushing it through the hole in the masonry.

6. If desired, once the horizontal pipe is in place,

the space between the pipe and masonry may be

lled with high-temperature grout.

7. Install a vented ashing at the top of the mason-

ry chimney. Stainless steel plate and screws are

recommended. Cut a hole for the vent pipe. If

needed, cut a second hole for the air intake pipe.

Seal all joints with high temperature waterproof

silicone sealant to prevent water leakage.

8. Install and seal ashing with high temperature

waterproof silicone sealant.

9. Seal and install vertical roof vent. If required, seal

and install a storm collar.

10. If desired, install a trim collar and use an addi-

tional horizontal vent pipe length, if required, to

connect the stove to the chimney.

5. INSTALLING THE OPTIONAL

HOPPER EXTENSION

To increase the hopper capacity, it is possible to

install a hopper extension, sold separatly. Consult

your dealer or website for details.

Page 15

INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

6. MOBILE HOME INSTALLATION

NOTICE

For mobile home installation, it is mandatory to

connect the stove to an outside combustion air

source. Insulated pipe should never exceed 10

feet.

When installed in a mobile home, the stove must be

anchored to the oor with two screws. Use the two

anchoring holes located on each side of the pedes-

tal, as shown on the right gure.

For use in a mobile home in Canada, this pellet

stove must be connected to a vent system certied

according to the standard or ULC/ORD-C441 CAN/

ULC-S609. A vent system meeting the requirements

of ULC S629M can also be used.

For use in a manufactured home in the United States,

this pellet stove must be connected to a venting sys-

tem that meets the requirements of UL 641 standard.

A vent system that meets the requirements of UL 103

standard may also be used.

7. INSTALLING A THERMOSTAT

Using a thermostat will help you maintain a constant

temperature throughout the house. A low voltage

thermostat (24 volts) is required. A xed wall mount

or hand held model can be used.

NOTICE

Thermostat manufacturer’s instructions always

override the information published in the following

section.

7.1 THERMOSTAT LOCATION

Location of the thermostat is very important to obtain

comfort and eciency from your stove.

Locate the thermostat 4 to 5 feet above the oor in

accordance with applicable building codes.

Install the thermostat in a location that provides

good airow characteristics and avoid areas behind

doors, near corners, air vents, direct sunlight or heat

generating devices.

If the thermostat is installed in the same room as the

stove, it should also be located at least 15 to 20 feet

from the stove. To prevent cycling, you should avoid

installing the thermostat on a poorly insulated outside

wall or directly in front of the stove.

A Thermostat

B

Minimum 15'

NOTICE

Installing the thermostat in front of the stove or

in front of a window will tend to make the stove

cycle too often and wear components prematurely.

See operation’s manual for more details on how to

operate the stove with the proper pilot mode.

Page 16 INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

7.2 WIRED THERMOSTAT

Before installing the thermostat, unplug the power

cord from the power outlet.

First, connect the two thermostat wires to the terminal

block located at the rear on the right hand side of the

stove when facing it. Loosen the two middle screws

and insert the wires in the terminals. Tighten the two

screws. Open the thermostat and connect the wires

as per the manufacturer’s instructions.

Open the thermostat and connect the wires as per

the manufacturer’s instructions.

Connect one wire on “RH” and the other wire on “W”.

Red wire jumper can remain installed. For further in-

formation refer to the manufacturer’s instructions.

7.3 WIRELESS THERMOSTAT

If you are using a wireless thermostat or a hand

held thermostatic remote control, connect the two

thermostat wires to the terminal block located at the

rear on the right hand side of the stove while facing it.

If the receiver wires are equipped with quick-connect

terminals you can connect them directly to the stove’s

wiring harness.

To do so, open the right hand side decorative panels

and disconnect wires (B) and (C) attached to the rear

of the terminal block (A) and connect them to the re-

ceiver.

8. COMBUSTION AIR SUPPLY

NOTICE

For mobile home installation, it is mandatory to

connect the stove to an outside combustion air

source. Insulated pipe should never exceed 10

feet.

It is recommended to install an outside air inlet in or

near the room where the stove is installed. When

doing so, it is preferable to choose a wall which is

not exposed to dominant winds, depending on the

conditions surrounding your house.

Page 17

INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

An insulated 3” inside diameter metallic pipe, either

exible or rigid, must be attached to the fresh air in-

take (D).

To complete the installation, make a hole of 1/4" to

1/2" (6 mm à 13 mm) bigger than the insulate pipe

diameter in the outside wall of the house at the

chosen location. From outside, place the outside air

inlet cap (E) in the hole (open side down) and fasten

the register to the wall, with screw.

Place the insulated pipe (A) over the register tube

and over the replace outside air connector (D).

At each end, carefully pull back the insulation and

plastic cover, exposing the exible pipe. Attach the

exible pipe using pipe clamps(C).

For a better seal, you may also use aluminum tape.

Wrap the tape around the joint between the exible

pipe and the air inlets. Carefully push the insulation

and plastic cover back over the pipe. Fix the plastic

in place using aluminum tape.

A rodent guard (minimum 1/4” wire mesh) must be

used at the termination. All connections must be

secured and airtight by either using the appropriately

sized hose clamp and/or UL-181-AP foil tape.

Make sure that the fresh air intake back draft shutter

functions freely. The fresh air intake back draft shutter

is located in the back of the stove.

8.1 SOURCES OF OUTSIDE COMBUSTION

AIR

CAUTION

IT IS FORBIDDEN TO DRAW COMBUSTION AIR

FROM A BASEMENT, AN ATTIC, A GARAGE OR

ANY CONFINED SPACE

• You can draw air from a ventilated crawl space

underneath the oor.

• You can draw air directly from an outside wall,

behind the stove.

Page 18 INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

9. APPLIANCE SET-UP

9.1 GENERAL

Make sure the fresh air intake back draft shutter

works freely.

Remove all tools or accessories that have been in-

serted in the stove for transportation purposes.

Test the door seal by closing and latching the door

on a strip of paper. Test all around the door. The

paper should not slip out easily. If it does, see the

maintenance section in the operation manual.

Install the bae

Page 19

INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

10. WIRING DIAGRAM

Page 20 INSTALLATION MANUAL ECO-55 / ECO-55 CT / ECO-55 ST

ENGLISH

11. EXPLODED VIEWS AND PARTS LIST DP00070 DP00072 AND DP00071

La page est en cours de chargement...

Drolet ECO-55 ST PELLET STOVE Guide d'installation

Ce manuel convient également à

Drolet ECO-55 ST PELLET STOVE Guide d'installation

dans d''autres langues

Documents connexes

Autres documents