VTech CS6429-16 Manuel utilisateur

User’s manual

w w w.v t e c h p h o n e s .c o m

Models:

CS6428-2/CS6429/

CS6429-15/CS6429-16/

CS6429-17/CS6429-2/

CS6429-3/CS6429-4/

CS6429-5

BC

Congratulations

on purchasing your new VTech product. Before using this telephone, please read

Important safety instructions on page 61 of this manual.

This manual has all the feature operations and troubleshooting necessary

to install and operate your new VTech telephone. Please review this manual

thoroughly to ensure proper installation and operation of this innovative and

feature rich VTech product. For support, shopping, and everything new at

VTech, visit our website at www.vtechphones.com. In Canada, please visit

www.vtechcanada.com.

Telephones identiﬁed with this logo have reduced noise and interference

when used with most T-coil equipped hearing aids and cochlear implants.

The TIA-1083 Compliant Logo is a trademark of the Telecommunications

Industry Association. Used under license.

Register online to get an additional 3-month warranty!

Visit www.vtechphones.com.

Registration

Register your product online for enhanced

warranty support.

Product news

Learn about the latest VTech products.

T

Compatible with

Hearing Aid T-Coil

TIA-1083

i

Table of contents

Getting started ................................1

Parts checklist ................................. 1

Telephone base and charger

installation .................................... 2

Battery installation ........................... 3

Battery charging .............................. 5

Installation options ........................... 6

Rewiring of telephone line for

cable/VoIP service users .............. 8

Telephone base layout ................... 9

Handset layout .............................. 10

Telephone settings .......................12

Using the menu ............................. 12

Ringer volume (telephone base) ... 12

Ringer volume (handset) ............... 13

Ringer tone .................................... 13

LCD language ................................ 14

Clear voicemail indicators .............. 15

Key tone ........................................ 15

Set date and time .......................... 16

Home area code ............................ 17

Dial mode ...................................... 17

Telephone operation ....................18

Make a call .................................... 18

Predial a call .................................. 18

Answer a call ................................. 18

End a call ....................................... 18

Speakerphone ............................... 18

Volume .......................................... 18

Mute ............................................... 19

Call waiting .................................... 19

Temporary ringer silencing ............ 19

Temporary tone dialing .................. 19

Redial list ....................................... 20

Review and dial a redial entry ....... 20

Store a number from the redial

list to the directory ...................... 20

Delete a redial entry ...................... 20

Chain dialing .................................. 21

Join a call in progress .................... 22

Find handset .................................. 22

Intercom ......................................... 23

Answer an incoming call during

an intercom call .......................... 24

Call transfer using intercom ........... 24

Directory ........................................26

About the directory ........................ 26

Create a new directory entry ......... 27

Review the directory ...................... 29

Alphabetical search ....................... 29

Dial a directory entry ...................... 29

Edit a directory entry ...................... 29

Delete a directory entry ................. 29

Speed dial ...................................... 30

Store a speed dial entry ................. 30

Dial a speed dial number ............... 31

Delete a speed dial entry ............... 31

Caller ID .........................................32

About caller ID ............................... 32

Information about caller ID with

call waiting .................................. 32

Call log ........................................... 33

Missed call indicator ...................... 34

Memory match ............................... 34

Review and dial from the call log ... 34

View dialing options ....................... 35

Save a call Iog entry to the

directory ..................................... 35

ii

Delete from the call log .................. 36

Call log display screen messages . 36

Answering system settings .........37

Answering system setup ................ 37

Answer on/off ................................. 37

Announcement .............................. 37

Record a new announcement ........ 38

Play the announcement ................. 38

Delete your announcement ........... 38

Call screening ................................ 39

Number of rings ............................. 39

Remote access code ..................... 39

Message alert tone ........................ 40

Recording time .............................. 40

Answering system operation ......41

Answering system and voicemail

indicators .................................... 41

Using the answering machine

and voicemail together .............. 41

Voice prompts ................................ 42

Message capacity .......................... 42

Answering system new message

indication .................................... 42

Call screening at the telephone

base ........................................... 42

Call screening at the handset ........ 43

Call intercept .................................. 43

Message playback ......................... 43

Delete all old messages ................ 45

Record, play or delete memos ....... 46

Message window displays ............. 47

Remote access .............................. 48

Appendix .......................................49

Handset display screen

messages ................................... 49

Handset and telephone base

indicators .................................... 51

Expand your telephone system ..... 52

Troubleshooting ............................. 53

Important safety instructions .......... 61

Operating range ............................. 63

Maintenance .................................. 63

The RBRC® seal ............................ 64

FCC, ACTA and IC regulations ..... 65

California Energy Commission

battery charging testing

instructions ................................. 67

For C-UL compliance only ............. 68

Limited warranty ............................ 71

Technical speciﬁcations ................. 73

Index ..............................................74

Table of contents

1

Parts checklist

Your telephone package contains the following items. Save your sales receipt and

original packaging in case it is necessary to ship your telephone for warranty service.

Telephone

line cord

Telephone baseHandset

(1 for CS6429/CS6429-16)

(2 for CS6428-2/CS6429-2)

(3 for CS6429-3)

(4 for CS6429-4)

(5 for CS6429-5)

Wall mount bracket

Getting started

Charger and charger adapter

(1 for CS6428-2/CS6429-2)

(2 for CS6429-3)

(3 for CS6429-4)

(4 for CS6429-5)

Battery

(1 for CS6429/CS6429-16)

(2 for CS6428-2/CS6429-2)

(3 for CS6429-3)

(4 for CS6429-4)

(5 for CS6429-5)

Telephone base

power adapter

Battery compartment cover

(1 for CS6429/CS6429-16)

(2 for CS6428-2/CS6429-2)

(3 for CS6429-3)

(4 for CS6429-4)

(5 for CS6429-5)

To purchase replacement batteries or power adapters, visit our website at

www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to

www.vtechcanada.com or call 1 (800) 267-7377.

Abridged user’s manual Quick start guide

2

Getting started

Telephone base and charger installation

Install the telephone base and charger(s) as shown below.

If you subscribe to digital subscriber line (DSL) high-speed Internet service

through your telephone line, you must install a DSL filter between the telephone

line cord and the telephone wall jack. Contact your DSL service provider for more

information about DSL filters.

The telephone base comes ready for tabletop use. If you want to mount your

telephone on a wall, refer to Tabletop to wall mount installation on page 6

for details.

ChargerTelephone base

Charger adapter

Electrical outlet

not controlled by

a wall switch

Telephone

line cord

A DSL filter (not

included) is required

if you have DSL high-

speed Internet service.

The DSL filter must

be plugged into the

telephone wall jack.

Telephone wall jack

Telephone base

power adapter

Electrical outlet

not controlled by

a wall switch

Use only the power adapters supplied with this product. To order a

replacement, visit our website at www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to www.vtechcanada.com or dial

1 (800) 267-7377.

The power adapters are intended to be correctly oriented in a vertical or floor

mount position. The prongs are not designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or cabinet outlet.

•

CAUTION: If you subscribe to telephone service from a cable company or a VoIP

service provider, plug the telephone line cord into the modem/router/terminal

adapter provided by your cable/VoIP service provider. Contact your cable/VoIP

service provider if you have any difficulties in installation.

3

Getting started

Battery installation

Install the battery as shown below.

Plug the battery connector securely into the socket inside the handset

battery compartment.

1.

Place the battery with the label THIS SIDE UP facing up and the wires inside

the battery compartment.

2.

Align the cover flat against the battery compartment, then slide it towards the

center of the handset until it clicks into place.

3.

Getting started

4

IMPORTANT:

Check for a dial tone by pressing . If you hear a dial tone, the installation

is successful.

If you do not hear a dial tone:

Make sure the installation procedures described above are properly done.

It may be a wiring problem. If you have changed your telephone service to

digital service from a cable company or a VoIP service provider, the telephone

line may need to be rewired to allow all existing telephone jacks to work.

Refer to Rewiring of telephone line for cable/VoIP service users on page 8

for more information.

•

If the handset will not be used for a long time, disconnect and remove the

battery to prevent possible leakage.

To purchase replacement batteries, visit our website at

www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to

www.vtechcanada.com or dial 1 (800) 267-7377.

•

Charge the handset by placing it in the telephone base or charger. The

CHARGE light is on when the handset is charging.

4.

Battery installation (continued)

CHARGE light

remains on when

charging.

Getting started

5

After you install your telephone or power returns following

a power outage, the handset will prompt you to set the date

and time. For instructions, see Set date and time on page

16. To skip setting the date and time, press OFF/CANCEL.

SET DATE

--/--/--

Battery charging

Once you have installed the battery, the screen indicates the battery status (see

the table below).

For best performance, keep the handset in the telephone base or charger when

not in use.

The battery is fully charged after 10 hours of continuous charging.

If you place the handset in the telephone base or the charger without plugging

in the battery, the screen displays NO BATTERY.

•

Battery indicators Battery status Action

The screen is blank,

or displays PLACE IN

CHARGER and flashes.

Battery has no or

very little charge. The

handset cannot be used.

Charge without interruption

(about 30 minutes).

The screen displays

LOW BATTERY and

flashes.

Battery has enough

charge to be used for a

short time.

Charge without interruption

(about 30 minutes).

The screen displays

HANDSET X.Battery is charged. To keep the battery charged,

place it in the telephone base

or charger when not in use.

When the battery is fully charged, you can expect the following performance:

Operation Operating time

While in handset use (talking*) Up to seven hours

While in speakerphone mode (talking*) Up to four hours

While not in use (standby**) Up to five days

*Operating times vary depending on your actual use and the age of the battery.

**Handset is not charging or in use.

Getting started

6

Installation options

The telephone comes ready for tabletop use. If you want to mount your telephone

on a wall, use the provided wall mount bracket to connect with a standard

dual-stud telephone wall mount plate. If you do not have this wall mount plate,

you can purchase one from many hardware or consumer electronics retailers.

You may need a professional to install the wall mount plate.

Tabletop to wall mount installation

Plug one end of the telephone line cord into the TEL LINE jack on the bottom

of the telephone base. Plug the small end of the base power adapter into the

POWER jack on the bottom of the telephone base.

Position the telephone base against the wall mount bracket. Insert the extend tabs

(marked B) of the wall mount bracket into the slots (marked B) on the back of the

telephone base. Push the telephone base down until it clicks securely in place.

Route the telephone line cord (or DSL filter) through the hole in the middle

of the wall mount bracket and plug it into the telephone wall jack. Route the

power cord out of the bottom of the telephone and plug it into an electrical

outlet not controlled by a wall switch.

Align the holes on the bracket with the standard wall mount plate and slide the

bracket down until it locks securely. Bundle the telephone line cord and power

adapter cord neatly with twist ties.

1.

2.

3.

4.

12

34

Getting started

7

Installation options (continued)

Wall mount to tabletop installation

If the telephone line cord and power adapter cord are bundled, untie

them first.

Slide the black wall mount bracket up and remove it from the wall mount plate.

Unplug the end of the telephone line cord (or DSL filter) from the telephone

wall jack. Unplug the power adapter from the power outlet.

Slide the telephone base up and remove it from the wall mount bracket.

See Telephone base and charger installation on page 2.

1.

2.

3.

4.

Getting started

8

Rewiring of telephone line for cable/VoIP service users

If you have changed to cable/VoIP service through a modem/router/terminal

adapter to establish telephone connection, the existing telephone jacks in your

home may no longer work. Your cable/VoIP service provider uses a seperate

cable connecting from the main line to the modem installed in your home.

To allow all existing telephone jacks to work, rewiring of the telephone line (as

indicated by the dotted line in the illustration below) may be needed. Rewiring

requires professional installation (fees may apply). Contact your cable/VoIP

service provider for more information.

OLD

Conventional

telephone line jack

Main

landline

NEW

Modem/Router/

Terminal adapter

Main cable

line

Getting started

9

Telephone base layout

X/DELETE

Press to delete the message currently

playing (page 44).

When the telephone is not in use, press

twice to delete all previously reviewed

messages (page 45).

Message window

Shows the number of messages and

other answering system information

(page 47).

IN USE light

Flashes when there

is an incoming call,

or another telephone

sharing the same line

is in use.

On when the handset

is in use, or the

answering system is

answering a call.

/FIND HANDSET

Press once and then

release to page all

system handsets

(page 22).

/SKIP

Press to skip to the next

message (page 44).

/PLAY/STOP

Press to play messages (page 44).

Press to stop message playback (page 44).

/ANS ON/OFF

Press to turn the answering

system on or off (page 37).

/REPEAT

Press to repeat a message or

press twice to play the previous

message (page 44).

/VOL and /VOL

Press to adjust

the volume during

message playback

(page 44).

When the phone is

not in use, press to

adjust the telephone

base ringer volume

(page 12).

10

/VOLUME

Press to enter the directory when the telephone is not in

use (page 29).

Press to scroll up while in a menu, or in the directory, call

log or redial list.

During a call or message playback, press to increase the

listening volume (page 18 or page 44).

When entering numbers or names in the directory, press

to move the cursor to the right.

Handset layout

Getting started

(speakerphone)

Press to make or answer a call.

During a call, press to switch between the speakerphone and

the handset (page 18).

CHARGE light

On when the handset is charging in the telephone base

or charger (page 4).

MUTE/DELETE

While on a call, press to mute the microphone (page 19).

While using the dialing keys, press to delete digits

or characters.

While the handset is ringing, press to silence the

ringer temporarily (page 19).

While reviewing the redial list, directory or call log, press to

delete an individual entry (pages 20, 29 and 36 respectively).

/FLASH

Press to make or answer a call (page 18).

During a call, press to answer an incoming call when

you receive a call waiting alert (page 19).

1

While reviewing a call log entry, press repeatedly to add

or remove 1 in front of the call log entry before dialing or

saving it to the directory.

TONE

Press to switch to tone dialing temporarily when using the

pulse service (page 19).

11

Handset layout

Getting started

MENU/SELECT

Press to show the menu.

While in a menu, press to select an item, or save an

entry or setting.

OFF/CANCEL

During a call, press to hang up.

While the handset is ringing, press to silence the ringer

temporarily (page 19).

While the telephone is not in use, press and hold to erase

the missed call indicator (page 34).

While in a menu, press to exit to the previous menu or

press and hold to exit to idle mode.

# (pound key)

Press repeatedly to show other dialing options when

reviewing a call log entry (page 35).

INT (intercom)

Press to start an intercom conversation or transfer a call

(pages 23-25).

REDIAL/PAUSE

Press to review the redial list (page 20).

While dialing or entering numbers into the directory,

press and hold to insert a dialing pause.

CID /VOLUME

Press to review the call log when the telephone

is not in use (page 34).

Press to scroll down while in a menu, or in the directory,

call log or redial list.

During a call or message playback, press to decrease the

listening volume (page 18 or page 44).

When entering numbers or names in the directory, press

to move the cursor to the left.

Dialing keys

Press to enter numbers or characters.

12

Using the menu

In the ringers menu, you can select the ringer tones and adjust the ringer volume

for incoming calls.

In the settings menu, you can change and edit the settings for LCD language,

voicemail indicators, key tone, date and time, home area code and dial mode.

Go to Answering system settings starting on page 37 for instructions on how

to modify the answering system settings with a system handset shown in the

table below.

Setting Page

Answer on/off 37

Announcement (play, record and delete) 38

Call screening 39

Number of rings 39

Remote access code 39

Message alert tone 40

Recording time 40

To enter the handset menu:

Press MENU/SELECT when the handset is not in use.

Press or until the screen displays the desired feature menu.

Press MENU/SELECT to enter that menu.

To return to the previous menu, press OFF/CANCEL.

To return to idle mode, press and hold OFF/CANCEL.

Ringer volume (telephone base)

Press /VOL or /VOL on the telephone base to adjust the ringer volume

when the telephone is not in use. When you set the ringer volume to zero, the

base ringer is off and the system announces, “Base ringer is off.”

1.

2.

3.

•

Telephone settings

13

Ringer volume (handset)

You can adjust the ringer volume or turn the ringer off.

Press MENU/SELECT when the handset is not in use.

Press or to select >RINGERS, then press

MENU/SELECT.

Press or to select >RINGER VOLUME, then press

MENU/SELECT.

Press or to adjust the volume. A sample of each ringer

volume plays as you scroll through the choices.

Press MENU/SELECT to save your selection. You hear a

confirmation tone.

The ringer volume also determines the ringer volume of

the intercom calls and the volume of paging tone.

When the handset ringer volume is set to off, that handset is silenced for all

incoming calls except paging tone and displays on the handset.

Unless the ringer volume is turned off on that handset, each handset rings

when there is an incoming call.

Ringer tone

You can choose from different ringer tones.

Press MENU/SELECT when the handset is not in use.

Press or to select >RINGERS, then press

MENU/SELECT.

Press or to select >RINGER TONE, then press

MENU/SELECT.

Press or to select a desired ringer tone. A sample of

each ringer tone plays as you scroll through the choices.

Press MENU/SELECT to save your selection. You hear a

confirmation tone.

1.

2.

3.

4.

5.

•

1.

2.

3.

4.

5.

If you turn off the handset ringer volume, you will not hear ringer tone samples.If you turn off the handset ringer volume, you will not hear ringer tone samples.

Telephone settings

>RINGERS

SETTINGS

>RINGER VOLUME

RINGER TONE

RINGER VOLUME

>RINGER TONE

RINGER VOLUME

RINGER TONE

>1

14

LCD language

You can select a language (English, French or Spanish) to be

used in all screen displays.

Press MENU/SELECT when the handset is not in use.

Press or to select >SETTINGS, then press MENU/SELECT.

Press or to select >LCD LANGUAGE, then press

MENU/SELECT.

Press or to choose ENGLISH, FRANÇAIS or

ESPAÑOL.

Press MENU/SELECT to save your selection. You hear a confirmation tone.

1.

2.

3.

4.

5.

Telephone settings

>LCD LANGUAGE

CLR VOICEMAIL

LCD LANGUAGE

>ENGLISH

15

Clear voicemail indicators

If you subscribe to voicemail service offered by your telephone service provider,

NEW VOICEMAIL and appear on the handset when you have new voicemail

messages. Contact your telephone service provider for more information about

using your voicemail service.

After you have listened to all new voicemail messages, the indicators on the

handset turn off automatically.

Use this feature when the telephone indicates that there is new voicemail but

there are none (for example, when you have accessed your voicemail while

away from home). This feature only turns off the indicators; it does not delete

your voicemail messages. As long as you have new voicemail messages, your

telephone service provider continues to send the signal to turn on the indicators.

To manually turn off these indicators:

Press MENU/SELECT when the handset is not in use.

Press or to select >SETTINGS, then press

MENU/SELECT.

Press or to select >CLR VOICEMAIL, then

press MENU/SELECT. The screen shows TURN OFF

INDICATOR?

Press MENU/SELECT to save your selection. You hear a

confirmation tone.

Key tone

You can turn the key tone on or off.

Press MENU/SELECT when the handset is not in use.

Press or to select >SETTINGS, then press

MENU/SELECT.

Press or to select >KEY TONE, then press

MENU/SELECT.

Press or to choose ON or OFF.

Press MENU/SELECT to save your selection. You hear a

confirmation tone.

1.

2.

3.

4.

1.

2.

3.

4.

5.

Your telephone service provider may alert you of new messages with a

stutter (broken) dial tone. Contact your telephone service provider for details.

Voicemail is different from answering system messages recorded in your

answering system. For more information about the difference, see page 41.

•

Your telephone service provider may alert you of new messages with a

stutter (broken) dial tone. Contact your telephone service provider for details.

Voicemail is different from answering system messages recorded in your

answering system. For more information about the difference, see page 41.

•

Telephone settings

>KEY TONE

SET DATE/TIME

KEY TONE

>ON

TURN OFF

INDICATOR?

HANDSET 1

NEW VOICEMAIL

3:15

PM

12/25

16

Set date and time

The answering system announces the date and time of each message prior to

playing it. If you subscribe to caller ID service, the day, month and time are set

automatically with each incoming call. However, the year must be correct so that

the day of the week can be calculated from the caller ID information. Before using

the answering system, set the date and time.

Press MENU/SELECT when the handset is not in use.

Press or to select >SETTINGS, then press

MENU/SELECT.

Press or to select >SET DATE/TIME, then press

MENU/SELECT.

When the month is flashing, press or until the screen

displays the correct month. Press MENU/SELECT to confirm.

-OR-

Press the dialing keys (0-9) to enter the current month (for

example, if the month is March, you must enter 03).

Repeat Step 4 to set the correct date and year and then

press MENU/SELECT to advance to set the time.

Repeat Step 4 until the time is set. Press or to choose

AM or PM, or press 2 for AM or 7 for PM. Press

MENU/SELECT to save your selection. You hear a confirmation tone.

1.

2.

3.

4.

5.

6.

If the date and time are not set, the system announces, “Time and date not set,”

before each message plays.

If the date and time are not set, the system announces, “Time and date not set,”

before each message plays.

Telephone settings

>SET DATE/TIME

HOME AREA CODE

SET DATE

11/20/10

SET TIME

10:30 PM

La page charge ...

VTech CS6429-16 Manuel utilisateur

VTech CS6429-16 Manuel utilisateur

dans d''autres langues

Documents connexes