VTech CS6429-15 Manuel utilisateur
- Catégorie
- Téléphones
- Taper
- Manuel utilisateur
Ce manuel convient également à
1
CS6428-2/CS6429/
CS6429-15/CS6429-16/
CS6429-2/ CS6429-3/
CS6429-4/CS6429-5
DECT 6.0 cordless telephone
Introduction
To protect our environment and conserve natural resources, this Abridged user’s
manual provides you with basic installation and use instructions. A limited set of
features are described in abbreviated form.
Please refer to the online User’s manual for a full set of installation and operation
instructions at www.vtechphones.com.
Before using this VTech product, please read Important safety instructions on
page 11 of this user’s manual.
Abridged user’s manual
Register online to get an additional 3-month warranty!
Go to www.vtechphones.com to register your product for enhanced warranty
support and latest VTech product news.
The ENERGY STAR
®
program (www.energystar.gov) recognizes and
encourages the use of products that save energy and help protect our
environment. We are proud to mark this product with the ENERGY STAR
®
label indicating it meets the latest energy efficiency guidelines.
Telephones identified with this logo have reduced noise and
interference when used with most T-coil equipped hearing aids and
cochlear implants. The TIA-1083 Compliant Logo is a trademark of
the Telecommunications Industry Association. Used under license.
Parts checklist
Your telephone package contains the following items. Save your sales receipt and
original packaging in the event warranty service is necessary.
Telephone line cord
Telephone base
Abridged user’s manual
Wall mount
bracket
Charger and charger adapter
(1 for CS6428-2/CS6429-2)
(2 for CS6429-3)
(3 for CS6429-4)
(4 for CS6429-5)
Battery
(1 for CS6429/CS6429-15/
CS6429-16)
(2 for CS6428-2/CS6429-2)
(3 for CS6429-3)
(4 for CS6429-4)
(5 for CS6429-5)
Telephone base
power adapter
Battery compartment cover
(1 for CS6429/CS6429-15/
CS6429-16)
(2 for CS6428-2/CS6429-2)
(3 for CS6429-3)
(4 for CS6429-4)
(5 for CS6429-5)
Quick start guide
Abridged user’s manual
Quick start guide
Handset
(1 for CS6429/CS6429-15/
CS6429-16)
(2 for CS6428-2/CS6429-2)
(3 for CS6429-3)
(4 for CS6429-4)
(5 for CS6429-5)
BC
T
Compatible with
Hearing Aid T-Coil
TIA-1083
2
Telephone base and charger installation
Install the telephone base and charger as shown below.
Telephone line cord
Telephone base
Charger
Telephone base
power adapter
A DSL filter (not included)
is required if you have DSL
high-speed Internet service
Electrical outlet
not controlled
by a wall switch
Electrical outlet
not controlled
by a wall switch
Telephone wall jack
Charger adapter
Use only the power adapter and battery supplied with this product. To order a
replacement, visit our website at www.vtechphones.com or call 1 (800) 595-9511.
In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
The power adapter is intended to be correctly oriented in a vertical or floor mount
position. The prongs are not designed to hold the plug in place if it is plugged into
a ceiling, under-the-table or cabinet outlet.
If you subscribe to telephone service from a cable company or a VoIP service
provider, plug the telephone line cord into the modem/router/terminal adapter
provided by your cable/VoIP service provider. Contact your cable/VoIP service
provider if you have any difficulties in installation.
•
•
•
Battery installation
Install the battery as shown below.
Slide the battery compartment
cover towards the center of the
handset until it clicks into place.
3. Place the handset in the telephone
base or charger to charge.
4.
Plug the battery connector
securely into the socket.
1. Place the battery with the label
THIS SIDE UP facing up and the wires
inside the battery compartment.
2.
If the handset will not be used for a long time, disconnect and remove the battery to
prevent possible leakage.
•
CHARGE light
remains on
when charging.
IMPORTANT:
Check for a dial tone by pressing . If you hear a dial tone, the installation
is successful.
If you do not hear a dial tone:
Make sure the installation procedures described above are properly done.
It may be a wiring problem. If you have changed your telephone service to
digital service from a cable company or a VoIP service provider, the telephone
line may need to be rewired to allow all existing telephone jacks to work. Refer
to Rewiring of telephone line for cable/VoIP service users on page 9 for
more information.
•
•
3
Tabletop to wall mount installation
The telephone comes ready for tabletop use. Follow the steps below to mount your
telephone on a wall.
Route the telephone line cord
through the hole on the wall mount
bracket and plug it into the telephone
wall jack. Route the power cord out
of the telephone base and plug it into
an electrical outlet not controlled by
a wall switch.
3. Align the holes on the bracket with
the standard wall plate and slide the
bracket down until it locks securely.
Bundle the telephone line cord
and power adapter cord neatly
with twist ties.
4.
Position the telephone base against
the wall mount bracket as shown.
Insert the extended tabs marked B
on the wall mount bracket into the
slots marked B on the back of the
telephone base. Push the telephone
base down until it clicks securely.
2.Plug one end of the telephone line
cord into the TEL LINE jack at the
bottom of the telephone base and
the base power adapter into the
POWER jack.
1.
Telephone base overview
X/DELETE
Delete the playing
message.
Press twice to delete
all previously reviewed
messages when the
phone is not in use.
Message window
Shows the number of messages and other
answering system information.
IN USE light
Flashes when there is an
incoming call, or another
telephone sharing the same
line is in use.
On when the handset is in
use, or the answering system
is answering a call.
/FIND HANDSET
Press once and then release
to page all system handsets.
/SKIP
Skip to the next message.
/PLAY/STOP
Play or stop playing messages.
/ANS ON/OFF
Turn the answering system
on or off.
/REPEAT
Press to repeat a message or press
twice to play the previous message.
/VOL and /VOL
Adjust the volume during
message playback.
Adjust the telephone
base ringer volume when
the phone is not in use.
Battery charging
Once you have installed the battery, the screen indicates the battery status (see
the table below).
For best performance, keep the handset in the telephone base or charger
when not in use.
The battery is fully charged after 10 hours of continuous charging.
If you place the handset in the telephone base or the charger without
plugging in the battery, the screen displays NO BATTERY.
•
•
•
Battery indicators Battery status Action
The screen is blank,
or displays PLACE IN
CHARGER and flashes.
Battery has no or
very little charge. The
handset cannot be used.
Charge without interruption
(about 30 minutes).
The screen displays
LOW BATTERY and
flashes.
Battery has enough
charge to be used for a
short time.
Charge without interruption
(about 30 minutes).
The screen displays
HANDSET X.
Battery is charged. To keep the battery charged,
place it in the telephone
base or charger when not
in use.
4
Using the handset menu
Press MENU when the phone is not in use.
Press or until the screen displays the desired feature menu.
Press SELECT to enter that menu.
To return to the previous menu, press CANCEL.
To return to idle mode, press and hold CANCEL.
Telephone settings
Default settings are indicated by asterisks (*).
Screen display Function Options
LCD LANGUAGE
Set the screen display language.
ENGLISH*
FRANÇAIS
ESPAÑOL
CLR VOICEMAIL
Turn off the voicemail indicators.
TURN OFF
INDICATOR?
KEY TONE
Turn an audible beep on or off whenever a key
is pressed.
ON*
OFF
SET DATE/TIME
Set the date and time shown on
the handset.
-:-- --/--
HOME AREA CODE
Enter your home area code if you dial only seven
digits for local calls.
_ _ _
DIAL MODE
Set the telephone to be tone or
pulse dialing.
TONE*
PULSE
The following are some of the telephone features you may wish to set. Refer to
Telephone settings in the online Complete user’s manual for detailed instructions
on setting all telephone features.
1.
2.
3.
•
•
Handset overview
CID /VOLUME
Review the call log when the phone is
not in use.
Decrease the listening volume during
a call or message playback.
Scroll down while in a menu, or in the
directory, call log or redial list.
Move the cursor to the left when
entering numbers or names.
/FLASH
Make or answer a call.
Answer another incoming call
during a call.
MUTE/DELETE
Mute the microphone during a call.
Delete digits or characters while
using the dialling keys.
Silence the ringer temporarily
while the handset is ringing.
Delete the displayed entry while in
the directory, call log or redial list.
CHARGE light
On when the handset is charging.
TONE
Switch to tone dialing
temporarily during a call.
Dialing keys
Enter numbers or characters.
/VOLUME
Review the directory when the
phone is not in use.
Increase the listening volume
during a call or message playback.
Scroll up while in a menu, or in the
directory, call log or redial list.
Move the cursor to the right when
entering numbers or names.
MENU/SELECT
Show the menu.
While in a menu, press to
select an item, or save an entry
or setting.
OFF/CANCEL
Hang up a call.
Silence the ringer temporarily
while the handset is ringing.
Press and hold to erase the
missed call indicator while the
phone is not in use.
Press to return to the previous
menu, or press and hold to
return to idle mode, without
making changes.
REDIAL/PAUSE
Press repeatedly to review the redial list.
Press and hold to insert a dialing pause
while entering numbers.
# (pound key)
Press repeatedly to show other
dialing options when reviewing
a call log entry.
1
Press repeatedly to add or
remove 1 in front of the call log
entry before dialing or saving it
to the directory.
(speakerphone)
Make or answer a call using the
handset speakerphone.
During a call, press to switch between
the speakerphone and the handset.
INT (intercom)
Start an intercom conversation or
transfer a call (for multi-handset
models only).
5
Ringer volume (handset)
You can adjust the ringer volume level, or turn the ringer off.
Press MENU when the handset is not in use.
Scroll to >RINGERS then press SELECT twice.
Press or to adjust the volume, then press SELECT to save.
If the handset ringer volume is set to off, that handset is silenced for all incoming
calls except paging tone.
The ringer volume also determines the ringer volume of the intercom calls and
the volume of the paging tone.
Set date and time
If you subscribe to caller ID service, the day, month and time are set automatically
with each incoming call. You can also set the date and time manually.
Press MENU when the handset is not in use.
Scroll to select >SETTINGS, then press SELECT.
Scroll to select >SET DATE/TIME, then press SELECT.
Use the dialing keys (0-9) to enter the month, date and year, then press SELECT.
Use the dialing keys (0-9) to enter the hour and minute.
Press or to choose AM or PM, or press 2 for AM or 7 for PM. Press
SELECT to save.
Voicemail indicators
If you subscribe to voicemail service offered by your telephone service provider,
NEW VOICEMAIL and appear on the handset when you have new voicemail
messages. Contact your telephone service provider for more information and
assistance about using your voicemail service. Refer to Clear voicemail indicators
in the online Complete user’s manual on how to clear the voicemail indicators.
Telephone operation
Make a call
Press or then dial the telephone number.
Answer a call
Press , or any dialing key.
End a call
Press OFF or put the handset to the telephone base or charger.
Speakerphone
During a call, press to switch between speakerphone and normal handset use.
Volume
During a call, press /VOLUME or /VOLUME to adjust the listening volume.
The handset earpiece volume setting and speakerphone volume setting
are independent.
Mute
The mute function allows you to hear the other party but the other
party cannot hear you.
During a call, press MUTE. The handset displays MUTE.
Press MUTE again to resume the conversation.
Call waiting
When you subscribe to call waiting service from your telephone service provider,
you hear an alert tone if there is an incoming call while you are on another call.
Press FLASH to put the current call on hold and take the new call.
Press FLASH at any time to switch back and forth between calls.
Temporary ringer silencing
When the telephone is ringing, you can temporarily silence the ringer of the handset
without disconnecting the call. The next call rings normally at the preset volume.
To silence the handset ringer, press OFF or MUTE on the handset.
RINGER MUTED and display.
Temporary tone dialing
If you have pulse (rotary) service only, you can switch from pulse to tone dialing
temporarily during a call.
During a call, press TONE .
Use the dialing keys to enter the relevant number. The
telephone sends touch-tone signals.
The telephone automatically returns to pulse dialing mode after
you end the call.
1.
2.
3.
•
•
1.
2.
3.
4.
5.
6.
•
•
•
•
•
1.
2.
•
•
•
1.
2.
3.
6
Find handset
Use this feature to find all system handsets.
To start paging:
Press /FIND HANDSET on the telephone base once and
then release. All idle handsets ring and their screens show
** PAGING **.
To end paging:
Press /FIND HANDSET again on the telephone base once
and then release.
Press , or any dialing key on the handset.
Place the handset in the telephone base or charger.
Do not press and hold /FIND HANDSET for more than four seconds. It may lead
to handset deregistration.
Redial list
Each handset stores the last 10 telephone numbers dialed.
To review and dial a number from the redial list:
Press REDIAL when the handset is not in use.
Press , , oror REDIAL repeatedly until the desired entry
displays.
Press to dial.
To delete a redial entry:
When the desired redial entry displays, press DELETE.
Join a call in progress
You can use up to four system handsets at a time on an outside call. You can buy
additional expansion handsets (CS6409) for this telephone base. You can register
up to five handsets to the telephone base.
When a handset is on a call, press or on another handset to join the call.
Press OFF to exit the call. The call continues until all handsets hang up.
Intercom
Use the intercom features for conversations between two handsets.
Press INT on your handset when not in use. When you have three or more
handsets, use the dialing keys to enter a destination handset number.
To answer the intercom call, press , , INT or any dialing key on the
destination handset.
To end an intercom call, press OFF or place the handset back in the telephone
base or charger.
Answer an incoming call during an intercom call
If you receive an outside call during an intercom call, there is an alert tone.
To answer the outside call, press . The intercom call ends automatically.
To end the intercom call without answering the outside call, press OFF. The
intercom call ends and the telephone continues to ring.
Call transfer using intercom
Use the intercom feature to transfer an outside call to another system handset.
During a call, press INT. When you have three or more handsets, use the
dialing keys to enter a destination handset number.
To answer the intercom call, press , , INT or any dialing key on the
destination handset. The outside call is now on hold and both handsets show
INTERCOM. You can have a private conversation with the destination handset.
From this intercom call, you have the following options:
You can let the destination handset join you on the outside call in a three-way
conversation. Press and hold INT on the original handset.
You can transfer the call. Press OFF, or place your handset back
in the telephone base or charger. Your handset screen shows
CALL TRANSFERRED. The destination handset then automatically
connects to the outside call.
You can press INT to switch between the outside call (OUTSIDE CALL
displays) and the intercom call (INTERCOM displays).
The destination handset can end the intercom call by pressing OFF, or by
placing the handset back in the telephone base or charger. The outside call
continues with the original system handset.
•
•
•
•
1.
2.
3.
•
•
1.
2.
3.
•
•
1.
2.
3.
•
•
•
•
7
Directory
The directory can store up to 50 entries and are shared by all system handsets.
To add a directory entry:
Press MENU/SELECT twice.
Scroll to >ADD CONTACT then press SELECT.
Use the dialing keys to enter the number (up to 30 digits).
-OR-
Copy a number from the redial list by pressing REDIAL and then press ,
or REDIAL repeatedly to select a number. Press SELECT.
Press SELECT to move to the name.
Use the dialing keys to enter the name (up to 15 characters). Additional key presses
show other characters of that particular key.
Press SELECT to save.
While entering names and numbers, you can:
Press DELETE to backspace and erase a digit or character.
Press and hold DELETE to erase the entire entry.
Press and hold PAUSE to insert a dialing pause (for entering phone numbers only).
Press or to move the cursor to the left or right.
Press 0 to add a space (for entering names only).
To review and dial from the directory:
Entries are sorted alphabetically.
Press when the handset is not in use.
Scroll to browse through the directory, or use the dialing keys to start a
name search.
When the desired entry appears, press or to dial.
To edit a directory entry:
When the desired entry displays, press SELECT.
Use the dialing keys to edit the number, then press SELECT.
Use the dialing keys to edit the name, then press SELECT to save.
To delete a directory entry:
When the desired entry displays, press DELETE.
When the screen displays DELETE CONTACT?, press SELECT.
Speed dial
You can copy up to 10 directory entries into the speed dial locations so that you
can dial these numbers using fewer keys than usual.
To store a speed dial entry:
Press MENU/SELECT twice when the handset is not in use.
Scroll to >SPEED DIAL, then press SELECT.
Scroll to a desired speed dial location, then press SELECT.
Scroll to a desired directory entry, then press SELECT to save.
To dial a speed dial entry:
Press and hold a dialing key (0-9) to display the desired speed dial entry when
the handset is not in use.
Press or to dial the displayed phone number.
To delete a speed dial entry:
When the desired entry displays, press DELETE.
Caller ID
This product supports caller ID services provided by most telephone service
providers. Depending on your service subscription, you may see the caller’s name,
number, date and time of calls that are sent by your telephone service provider after
the first or second ring.
Call log
The call log stores up to 50 entries. If you answer a call before the caller
information appears, it will not be saved in the call log.
The handset displays XX MISSED CALLS when there are calls that have not
been reviewed in the call log.
If you want to erase the missed call indicator, press and hold CANCEL on the
idle handset.
To review and dial a number in the call log:
Press CID when the handset is not in use.
Scroll to browse through the call log. When the desired entry appears:
Press # (pound key) repeatedly to show different dialing options.
Press 1 repeatedly if you need to add or remove 1 in front of the
phone number.
Press to dial the displayed number.
1.
2.
•
•
3.
4.
5.
•
•
•
•
•
1.
2.
3.
1.
2.
3.
1.
2.
1.
2.
3.
4.
1.
2.
•
•
1.
2.
•
•
3.
8
To save a call log entry to the directory:
When the desired call log entry displays, press SELECT.
Use the dialing keys to modify the number, then press SELECT.
Use the dialing keys to modify the name, then press SELECT to save.
To delete one call log entry:
When the desired call log entry displays, press DELETE.
To delete all call log entries:
Press MENU when the handset is not in use. Scroll to >CALL LOG and then
press SELECT. Scroll to >DEL ALL CALLS and then press SELECT twice.
About the answering system
The answering system can record up to 99 messages, depending on the length of
each message. The total recording time is approximately 14 minutes.
Answering system settings
Default settings are indicated by asterisks (*).
Screen display Function Options
CALL SCREENING
Set whether you hear the callers while they are
leaving messages to you.
ON*
OFF
# OF RINGS
Set the number of times the telephone rings before
the answering system answers.
6; 5; 4; 3*; 2;
TOLL SAVER
REMOTE CODE
Set a two-digit security code to access the
answering system remotely from any touch-tone
telephone.
19*
MSG ALERT TONE
Set to alert you when you have new messages.
ON
OFF*
RECORDING TIME
Set the recording time for each incoming message.
3 MINUTES*
2 MINUTES
1 MINUTE
Number of rings
You can set the answering system to answer an incoming call after 2, 3, 4, 5 or 6 rings;
or toll saver. If you choose toll saver, the answering system answers a call after 2 rings
when you have new messages, or after 4 rings when you have no new messages.
Press MENU when the handset is not in use.
Scroll to >ANSWERING SYS then press SELECT.
Scroll to >ANS SYS SETUP then press SELECT.
Scroll to ># OF RINGS then press SELECT.
Press or to choose 2, 3, 4, 5, 6 or TOLL SAVER and then press SELECT.
Answering system operation
Turn the answering system on or off
The answering system must be turned on to answer and record messages.
Press /ANS ON/OFF on the telephone base to turn the built-in answering
system on or off.
Record your own announcement with a handset
You can use the preset announcement to answer calls, or replace it with your own
recorded announcement. It can be up to 90 seconds in length.
Press MENU when the handset is not in use.
Scroll to >ANSWERING SYS and then press SELECT twice.
The handset announces, “To play, press 2. To record, press 7.” Press 7 to record.
The handset announces, “Record after the tone. Press 5 when you are done.”
After the tone, speak towards the handset microphone. Press 5 when done.
The answering system automatically plays back the newly recorded announcement.
Press 5 to stop the playback at any time; 2 to replay the recorded announcement;
3 to delete the recorded announcement; or 7 to record again if desired.
Message playback at the telephone base
Press /PLAY/STOP when the phone is not in use.
Options during playback:
Press VOL or VOL to adjust the speaker volume.
Press /SKIP to skip to the next message.
Press /REPEAT to repeat the message currently playing. Press /REPEAT
twice to listen to the previous message.
Press X/DELETE to delete the playing message. The system advances to the
next message.
Press /PLAY/STOP to stop.
Delete all messages at the telephone base
Press X/DELETE twice when the phone is not in use.
1.
2.
3.
•
•
1.
2.
3.
4.
5.
•
1.
2.
3.
4.
5.
•
•
•
•
•
9
Call screening at the telephone base
If the answering system and call screening are on, the announcement and the
incoming message broadcast at the telephone base when a call is answered by
the answering system.
Options while recording a message:
Press VOL or VOL on the telephone base to adjust the call screening volume
.
Press /PLAY/STOP to temporarily turn on or off call screening.
Press VOL to temporarily turn on call screening when it is set to off.
Call intercept
If you want to talk to the person whose message is being recorded, press or
on the handset.
Add and register a handset
The handsets provided with your telephone system are already registered. Each
handset is assigned a number that displays on the handset. Additional handsets
registered to the telephone system are assigned numbers in the sequential order.
This telephone system accommodates up to five handsets.
You can add new handsets (CS6409, purchased separately) to your telephone
system. Each handset must be registered with the telephone base before use.
When first purchased and properly charged, each expansion handset shows
1.PRESS FIND HS ON BASE 4 SEC and 2.THEN PRESS # ON HANDSET
alternately. Charge the handset before registering it to the telephone base.
To register a handset:
Place the non-registered handset in the telephone base or charger.
On the telephone base, press and hold /FIND HANDSET for about
four seconds until the red IN USE light turns on.
On the handset, press # (pound key) then the handset shows REGISTERING.....
PLEASE WAIT. Then the handset shows HANDSET REGISTERED and you
hear a beep when the registration process completes. The registration process
takes about 60 seconds to complete.
Replace a handset
If you want to replace a handset or reassign the designated handset number of a
registered handset, you must deregister all handsets and then individually register
each handset.
To deregister all handsets:
Press and hold /FIND HANDSET on the telephone base for about 10 seconds
until the IN USE light on the telephone base turns on and starts flashing.
Press and release /FIND HANDSET again. You must press /FIND HANDSET
while the IN USE light is still flashing. The IN USE light flashes for approximately
five seconds.
All handsets show 1.PRESS FIND HS ON BASE 4 SEC and
2.THEN PRESS # ON HANDSET alternately when the deregistration process
completes. The deregistration process takes about 10 seconds to complete.
Rewiring of telephone line for cable/VoIP service users
If you have changed to cable/VoIP service through a modem/router/terminal
adapter to establish telephone connection, the existing telephone jacks in your
home may no longer work. Your cable/VoIP service provider uses a separate cable
connecting from the main line to the modem installed in your home.
To allow all existing telephone jacks to work, rewiring of the telephone line (as
indicated by the dotted line in the illustration below) may be needed. Rewiring
requires professional installation (fees may apply). Contact your cable/VoIP
service provider for more information.
•
•
•
1.
2.
3.
1.
2.
3.
OLD
Conventional
telephone line jack
Main
landline
NEW
Modem/Router/
Terminal adapter
Main cable
line
10
Troubleshooting
If you have difficulty with your telephone, please try the suggestions below. For
customer service, visit our website at www.vtechphones.com or call 1 (800) 595-9511.
In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
My telephone does not work at all.
Make sure the battery is installed and charged correctly. For optimum daily performance,
return the handset to the telephone base or charger after use.
Make sure the power adapter is securely plugged into an outlet not controlled by a wall switch.
Make sure the telephone line cord is plugged firmly into the telephone base and the wall jack.
Unplug the electrical power to the telephone base. Wait for approximately 15 seconds,
then plug it back in. Allow up to one minute for the cordless handset and telephone base to
synchronize.
Charge the battery in the handset for up to 10 hours.
If the battery is completely depleted, it may take up to 30 minutes to charge the handset
before LOW BATTERY appears on the screen.
Remove and install the battery again. If that still does not work, it may be necessary to
purchase a new battery.
Disconnect the telephone base from the telephone wall jack and plug in a working telephone.
If the other telephone does not work, the problem is probably in the wiring or telephone
service. Contact your telephone service provider.
The display shows NO LINE. I cannot get a dial tone.
Try all the above suggestions.
Make sure the telephone line cord is plugged firmly into the telephone base and the wall jack.
Disconnect the telephone line cord from your telephone and connect it to another telephone.
If there is no dial tone on that other telephone either, then the telephone line cord may be
defective. Try installing a new telephone line cord.
If changing the telephone line cord does not help, the wall jack (or the wiring to this wall jack)
may be defective. Contact your telephone service provider.
I cannot dial out.
Try all the above suggestions.
Make sure there is a dial tone before dialing. It is normal if the handset takes a second or
two to synchronize with the telephone base before producing a dial tone. Wait an extra
second before dialing.
If other telephones in your home are having the same problem, the problem is in the wiring
or telephone service. Contact your telephone service provider (charges may apply).
Eliminate any background noise. Mute the cordless handset before dialing, or dial from
another room in your home with less background noise.
The answering system does not answer after correct number of rings.
Make sure the answering system is on. When the answering system is on, ANS ON should
show on the handset and the /ANSWER ON/OFF light is lit on the telephone base.
If toll saver is selected, the number of rings changes to two when there are new messages.
If the memory is full or the answering system is off, the answering system answers after 10
rings. In some cases, the answering system is affected by the ringing system used by the
telephone service provider.
If you subscribe to voicemail service, change the number of rings so that your answering
system answers before your voicemail answers. To get help with your voicemail settings,
contact your telephone service provider.
If there is a fax machine connected to the same telephone line, try disconnecting the fax
machine. If that solves the problem, consult your fax machine documentation for information
on compatibility with answering systems.
The answering system does not record messages.
Make sure the answering system is on.
Make sure the memory of the answering system is not full. When the answering machine
memory is full, it does not record new messages until some old messages are deleted.
If you subscribe to voicemail service, change the number of ring so that your answering
system answers before your voicemail answers. To determine how many rings activate your
voicemail, contact your telephone service provider.
If there is a fax machine connected to the same telephone line, try disconnecting the fax
machine. If that solves the problem, consult your fax machine documentation for information
on compatibility with answering systems.
The messages on the answering system are incomplete.
If a caller leaves a very long message, part of it may be lost when the answering system
disconnects the call after the preset recording time.
If the memory on the answering system becomes full during a message, the answering
system stops recording and disconnects the call.
If the caller’s voice is very soft, the answering system may stop recording and disconnect
the call.
Common cure for electronic equipment.
If the telephone is not responding normally, put the cordless handset in the telephone base.
If this does not fix the problem, do the following (in the order listed):
1. Disconnect the power to the telephone base.
2. Disconnect the battery on the cordless handset.
3. Wait a few minutes before connecting power to the telephone base.
4. Install the battery again and place the cordless handset in the telephone base .
5. Wait for the cordless handset to synchronize with the telephone base. Allow up one
minute for this to take place.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
11
Important safety instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce
the risk of fire, electric shock and injury, including the following:
Read and understand all instructions.
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use
a damp cloth for cleaning.
Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement or shower.
Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation.
To protect them from overheating, these openings must not be blocked by placing the product on a soft
surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat
register. This product should not be placed in any area where proper ventilation is not provided.
This product should be operated only from the type of power source indicated on the marking label. If you
are not sure of the type of power supply in your home or office, consult your dealer or local power company.
Do not allow anything to rest on the power cord. Do not install this product where the cord may be
walked on.
Never push objects of any kind into this product through the slots in the telephone base or handset
because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any
kind on the product.
To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized
service facility. Opening or removing parts of the telephone base or handset other than specified
access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can
cause electric shock when the product is subsequently used.
Do not overload wall outlets and extension cords.
Unplug this product from the wall outlet and refer servicing to an authorized service facility under
the following conditions:
When the power supply cord or plug is damaged or frayed.
If liquid has been spilled onto the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operation instructions. Improper adjustment of other controls may
result in damage and often requires extensive work by an authorized technician to restore the
product to normal operation.
If the product has been dropped and the telephone base and/or handset has been damaged.
If the product exhibits a distinct change in performance.
Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of
electric shock from lightning.
Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain
circumstances, a spark may be created when the adapter is plugged into the power outlet, or
when the handset is replaced in its cradle. This is a common event associated with the closing of
any electrical circuit. The user should not plug the phone into a power outlet, and should not put a
charged handset into the cradle, if the phone is located in an environment containing concentrations
of flammable or flame-supporting gases, unless there is adequate ventilation. A spark in such an
environment could create a fire or explosion. Such environments might include: medical use of
oxygen without adequate ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.); a
leak of natural gas; etc.
Only put the handset of your telephone next to your ear when it is in normal talk mode.
The power adapters are intended to be correctly oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or
cabinet outlet.
SAVE THESE INSTRUCTIONS
Battery
CAUTION: Use Only Supplied Battery.
Do not dispose of the battery in a fire. Check with local waste management codes for special
disposal instructions.
Do not open or mutilate the battery. Released electrolyte is corrosive and may cause burns or injury
to the eyes or skin. The electrolyte may be toxic if swallowed.
Exercise care in handling batteries in order not to create a short circuit with conductive materials.
Charge the battery provided with or identified for use with this product only in accordance with the
instructions and limitations specified in this manual.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary
evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers.
Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
Should keep wireless telephones at least six inches from the pacemaker.
Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket,
when it is turned ON.
Should use the wireless telephone at the ear opposite the pacemaker. WTR’s evaluation did not identify
any risk to bystanders with pacemakers from other persons using wireless telephones.
About cordless telephones
Privacy: The same features that make a cordless telephone convenient create some
limitations. Telephone calls are transmitted between the telephone base and the cordless
handset by radio waves, so there is a possibility that the cordless telephone conversations
could be intercepted by radio receiving equipment within range of the cordless handset. For this
reason, you should not think of cordless telephone conversations as being as private as those
on corded telephones.
Electrical power: The telephone base of this cordless telephone must be connected to a
working electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls
cannot be made from the cordless handset if the telephone base is unplugged, switched off or if
the electrical power is interrupted.
Potential TV interference: Some cordless telephones operate at frequencies that may cause
interference to televisions and VCRs. To minimize or prevent such interference, do not place
the telephone base of the cordless telephone near or on top of a TV or VCR. If interference is
experienced, moving the cordless telephone farther away from the TV or VCR often reduces or
eliminates the interference.
Rechargeable batteries: Exercise care in handling batteries in order not to create a short
circuit with conducting material such as rings, bracelets, and keys. The battery or conductor
may overheat and cause harm. Observe proper polarity between the battery and the battery
charger.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
A.
B.
C.
D.
E.
F.
13.
14.
15.
16.
•
•
•
•
•
•
•
•
•
•
•
12
Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do
not burn or puncture the battery. Like other batteries of this type, if burned or punctured, they could
release caustic material which could cause injury.
Operating range
This cordless telephone operates with the maximum power allowed by the Federal Communications Commission
(FCC). Even so, this handset and telephone base can communicate over only a certain distance - which can vary
with the locations of the telephone base and handset, the weather, and the layout of your home or office.
When the handset is out of range, the handset displays OUT OF RANGE OR NO PWR AT BASE.
If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not connect well
when you press . Move closer to the telephone base, then press to answer the call.
If the handset moves out of range during a telephone conversation, there may be interference. To improve
reception, move closer to the telephone base.
Maintenance
Taking care of your telephone
Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect your telephone if you ever need
to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with
wet hands. Do not install the telephone base near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety,
take caution when using electrical appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft
cloth slightly dampened with water or mild soap. Do not use excess water or cleaning solvents of any kind.
The RBRC
®
seal
The RBRC
®
seal on the nickel-metal hydride battery indicates that VTech Communications,
Inc. is voluntarily participating in an industry program to collect and recycle these batteries at
the end of their useful lives, when taken out of service within the United States and Canada.
The RBRC
®
program provides a convenient alternative to placing used nickel-metal hydride
batteries into the trash or municipal waste, which may be illegal in your area.
VTech’s participation in RBRC
®
makes it easy for you to drop off the spent battery at local
retailers participating in the RBRC
®
program or at authorized VTech product service centers.
Please call 1 (800) 8 BATTERY
TM
for information on Ni-MH battery recycling and disposal
bans/restrictions in your area. VTech’s involvement in this program is part of its commitment
to protecting our environment and conserving natural resources.
RBRC
®
is a registered trademark of Rechargeable Battery Recycling Corporation.
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under
Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide
reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Privacy of communications may not be ensured
when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can
be safely absorbed by a user or bystander according to the intended usage of the product. This product has
been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the
user. The telephone base shall be installed and used such that parts of the user’s body other than the hands
are maintained at a distance of approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B).
•
•
•
•
•
Remember that electrical appliances can cause serious injury if used when you are wet or standing in
water. If the telephone base should fall into water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE
POWER CORD AND TELEPHONE LINE CORD FROM THE WALL. Then remove the telephone by the
unplugged cords.
13
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the
Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment
contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be
provided to your telephone service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network must comply
with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and
modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is
also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two
lines. See the installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your
telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th
and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but
not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your
telephone service provider.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected
to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have
questions about what will disable alarm equipment, consult your telephone service provider or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been
corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents.
For repair procedures, follow the instructions outlined under the Limited warranty.
If this equipment is causing harm to the telephone network, the telephone service provider may temporarily
discontinue your telephone service. The telephone service provider is required to notify you before
interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be
given the opportunity to correct the problem and the telephone service provider is required to inform you of
your right to file a complaint with the FCC. Your telephone service provider may make changes in its facilities,
equipment, operation, or procedures that could affect the proper functioning of this product. The telephone
service provider is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g.,
police, fire, medical) in these locations. If you do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired
operation.
Privacy of communications may not be ensured when using this phone.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical
specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an
indication of the maximum number of devices allowed to be connected to a telephone interface.
The termination on an interface may consist of any combination of devices subject only to the
requirement that the sum of the RENs of all the devices does not exceed five.
This product meets the applicable Industry Canada technical specifications.
For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures corporelles ou d’électrocution, suivez toujours
ces mesures préventives de base lorsque vous utilisez votre téléphone :
Lisez et comprenez bien toutes les instructions.
Observez toutes les instructions et mises en garde inscrites sur l’appareil.
Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas de nettoyeurs
liquides ni en aérosol. N’utilisez qu’un chiffon doux et légèrement humecté.
N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier de cuisine,
d’un bac de lavage ou d’une piscine, ou dans un sous-sol humide ou sous la douche.
Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil pourrait
tomber et être sérieusement endommagé.
Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière ou en
dessous. Afin d’empêcher la surchauffe, ces ouvertures ne doivent pas être obstruées en plaçant
l’appareil sur un lit, divan, tapis ou autre surface similaires. Ne placez pas cet appareil à proximité
d’un élément de chauffage ni d’une plinthe électrique. De plus, ne l’installez pas dans une unité
murale ou un cabinet fermé qui ne possède pas d’aération adéquate.
Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les étiquettes de
l’appareil. Si vous ne connaissez pas le voltage de votre maison, consultez votre marchand ou
votre fournisseur d’électricité.
Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit sécuritaire,
là où personne ne pourra trébucher sur la ligne d’alimentation ni le cordon téléphonique
modulaire.
N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils pourraient
toucher à des points de tension dangereux ou court-circuiter des pièces, ce qui constituerait un
risque d’incendie ou d’électrocution. N’échappez pas de liquides dans l’appareil.
Afin de réduire les risques d’électrocution, ne démontez pas l’appareil, mais apportez-le plutôt
à un centre de service qualifié s’il doit être réparé. En enlevant le couvercle, vous vous exposez
à des tensions dangereuses ou autres dangers similaires. Un remontage inadéquat peut être à
l’origine d’une électrocution lors d’une utilisation ultérieure de l’appareil. Débranchez l’appareil
avant de procéder au nettoyage. Utilisez un chiffon humide et doux.
Ne surchargez pas les prises de courant et les rallonges.
Débranchez cet appareil de la prise de courant et communiquez avec le département de
service à la clientèle de VTech dans les cas suivants:
Lorsque le cordon d’alimentation est endommagé ou écorché.
Si du liquide a été échappé dans l’appareil.
Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.
Si le produit ne fonctionne pas normalement en respectant les instructions de
fonctionnement. Réglez uniquement les commandes indiquées dans le les instructions de
fonctionnement. Les réglages incorrects des autres commandes pourraient provoquer un
dommage qui pourrait exiger un travail exhaustif de la part d’un technicien autorisé afin de
rétablir le fonctionnement normal de l’appareil.
Si le produit a été échappé et que le socle et/ou le combiné a été endommagé.
Si le produit affiche une nette diminution de sa performance.
Évitez d’utiliser un téléphone (autre qu’un sans fil) pendant un orage. Les éclairs peuvent être à
l’origine d’une électrocution.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
•
•
•
•
•
•
13.
14
N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite. En certaines
circonstances, une flammèche pourrait être provoquée lorsque l’adaptateur est branché à une
prise de courant, ou lorsque le combiné est déposé sur le socle. Ceci est un événement commun
associé à la fermeture d’un circuit électrique. L’utilisateur ne devrait pas brancher le téléphone à
une prise de courant, et ne devrait pas déposer le combiné chargé sur le socle, si le téléphone
se trouve à proximité d’un endroit comportant des concentrations de gaz inflammables, à
moins que la ventilation soit adéquate. Une flammèche dans un tel endroit pourrait provoquer
un incendie ou une explosion. De tels environnements peuvent comprendre: des endroits où
l’on utilise de l’oxygène médical sans ventilation adéquate; des gaz industriels (dissolvants de
nettoyage, des vapeurs d’essence, etc.); une fuite de gaz naturel, etc.
Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode de
conversation.
Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés au sol. Les
broches ne sont pas conçues pour maintenir l’adaptateur en place si celui-ci est barnché dans une
prise au plafond ou sous une table/ armoire.
CONSERVEZ CES INSTRUCTIONS
Pile
MISE EN GARDE : N’utilisez que la pile incluse.
Ne jetez pas la pile au feu. Vérifiez les instructions spécifiques de mise aux rebus auprès des
autorités locales.
N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif et pourrait
causer des brûlures ou des blessures aux yeux ou à la peau. L’électrolyte est toxique si avalé.
Soyez prudents lorsque vous manipulez les piles afin d’éviter les courts-circuits provoqués par
des matériaux conducteurs. .
Rechargez la pile incluse ou identifiée pour fonctionner avec cet appareil, selon les instructions
et limites spécifiées dans ce guide d’utilisation.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a
mené une évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs et les
stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des aliments et
drogues (FDA) des États-Unis, la firme WTR recommande aux médecins :
Avis aux détenteurs de stimulateurs cardiaques
Ils doivent tenir le téléphone sans fil à une distance d’au moins six pouces du stimulateur
cardiaque.
Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que
dans une poche de chemise, lorsque celui-ci est en marche.
Ils doivent utiliser le téléphone sans fil en l’appuyant sur l’oreille qui se trouve dans la direction
opposée au stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de
simulateurs cardiaques causés par les gens qui utilisent un téléphone sans fil à proximité de ceux-
ci.
À propos des téléphones sans fil
Condentialité : Les mêmes caractéristiques qui constituent des avantages pour les téléphones
sans fil affichent également des restrictions. Les appels téléphoniques sont transmis entre
le combiné sans fil et le socle par le biais d’ondes radio ; il y a donc la possibilité que vos
conversations téléphoniques sans fil soient interceptées par des équipements de réception radio
se trouvant dans la portée du combiné sans fil. Pour cette raison, vous ne devez pas percevoir
les communications téléphoniques sans fil comme étant aussi confidentielles que celles des
téléphones à cordons.
Alimentation électrique : Le socle de ce téléphone sans fil doit être branché à une prise
électrique fonctionnelle. La prise électrique ne doit pas être contrôlée par un interrupteur mural.
Les appels ne pourront pas être effectués du combiné sans fil si le socle est débranché ou mis
hors tension ou si le courant est coupé.
Possibilité d’interférences aux téléviseurs : Certains téléphones sans fil fonctionnent sur
des fréquences pouvant causer des interférences aux téléviseurs et aux magnétoscopes. Pour
réduire ou prévenir de telles interférences, ne placez pas le socle du téléphone sans fil près ou
sur un téléviseur ou magnétoscope. S’il y a présence de parasites, il est conseillé d’éloigner
le téléphone sans fil du téléviseur ou du magnétoscope afin de réduire possiblement les
interférences.
Piles rechargeables : Manipulez les piles avec soin afin de ne pas les court-circuiter avec des
bagues, bracelets ou clés. Les piles ou le conducteur peut surchauffer et causer des blessures.
Respectez la polarité adéquate entre la pile et le chargeur.
Les bloc-piles rechargeables à l’hydrure métallique de nickel : Jetez ces blocs-piles de
manière écologique et sécuritaire. Ne les incinérez pas et ne les percez pas. Tel que les autres
piles de ce type, elles pourraient dégager une matière toxique qui peut causer des blessures
corporelles si elles sont brûlées ou percées.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or
“you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects in
material and workmanship, pursuant to the following terms and conditions, when installed and used normally
and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer
for Products purchased and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during
the limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace at
VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new
or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or
refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment.
Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the
repaired or replacement Products to you in working condition. You should expect the repair or replacement to
take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs
or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies
to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement
Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.
14.
15.
16.
•
•
•
•
•
•
•
•
•
•
•
•
•
15
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper
installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone other than an
authorized service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or
cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have
been removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or
Canada, or used for commercial or institutional purposes (including but not limited to Products used for
rental purposes); or
7. Product returned without a valid proof of purchase (see item 2 on the next page); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems
outside the unit.
How do you get warranty service?
To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and
features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and
are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location.
VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling
charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not
covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will
notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for
the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
Return the entire original package and contents including the Product to the VTech service location
along with a description of the malfunction or difficulty; and
Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model)
and the date of purchase or receipt; and
Provide your name, complete and correct mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other
written or oral communications related to this Product. VTech provides no other warranties for this Product.
The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other
express warranties. No one is authorized to make modifications to this limited warranty and you should not
rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights,
which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and
merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the
date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the
above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental,
consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the
Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting
from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
1.
2.
3.
16
Technical specifications
Transmit frequency Handset: 1921.536-1928.448 MHz
Telephone base: 1921.536-1928.448 MHz
Channels 5
Nominal effective range Maximum power allowed by FCC and IC. Actual operating
range may vary according to environment conditions at the
time of use.
Power requirements Handset: 2.4V Ni-MH battery
Telephone base: 6V DC @ 400mA
Charger: 6V AC @ 300mA
Memory Handset directory:
50 memory locations; up to 30 digits and 15 characters
Handset call log:
50 memory locations; up to 24 digits and 15 characters
VTech Communications, Inc.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
© 2014 VTech Communications, Inc.
All right reserved. 05/14. CS6429-X_ACIB_V2.0
Document order number: 91-007232-020-100
Designed to fit your home.
And your life.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
VTech CS6429-15 Manuel utilisateur
- Catégorie
- Téléphones
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: VTech CS6429-15 User manual
Documents connexes
-
VTech LS6185-13 Manuel utilisateur
-
VTech CS6649 Manuel utilisateur
-
VTech CS6859 Manuel utilisateur
-
VTech CS6759 Manuel utilisateur
-
-
VTech LS6105-13 Manuel utilisateur
-
-
VTech SN5147 Important Safety Instructions
-
VTech CS6948-3 Manuel utilisateur
-
VTech LS6195-17 Manuel utilisateur
