AT&T CRL32102 Manuel utilisateur

CRL32102/CRL32202/CRL32302/

CRL32352/CRL32452

DECT 6.0 cordless telephone/

answering system with

caller ID/call waiting

Abridged user’s manual

This Abridged user’s manual provides you with basic installation and

major operation instructions. A limited set of features are described in an

abridged form.

Please refer to the online CRL32102/CRL32202/CRL32302/CRL32352/

CRL32452 DECT 6.0 cordless telephone/answering system with

caller ID/call waiting Complete user’s manual for a full set of installation

and operation instructions at www.telephones.att.com/manuals.

For customer service, visit our website at www.telephones.att.com or

call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

This telephone system is compatible with certain AT&T DECT 6.0 cordless

headsets. Visit www.telephones.att.com/headsets for a list of

compatible cordless headsets.

Serial number: __________________________________________________________

Purchase date: _________________________________________________________

Place of purchase: ______________________________________________________________

Both the model and serial numbers of your AT&T product can be found on

the bottom of the telephone base.

Save your sales receipt and original packaging in case it is necessary to

return your telephone for warranty service.

Model number:

Type:

CRL32102 (one handset)

CRL32202 (two handsets)

CRL32302 (three handsets)

CRL32352 (three handsets)

CRL32452 (four handsets)

DECT 6.0 cordless telephone/answering system

with caller ID/call waiting

the AT&T logo are trademarks of AT&T Intellectual Property licensed to

Advanced American Telephones, San Antonio, TX 78219. Printed in China.

Parts checklist

Your telephone package contains the following items. Save your sales receipt

and original packaging in the event warranty service is necessary.

Power adapter for

telephone base

Telephone base

Abridged user’s manual Quick start guide

Wall-mount bracket

Charger for cordless handset

with power adapter installed

(1 for CRL32202)

(2 for CRL32302/CRL32352)

(3 for CRL32452)

Cordless handset

(1 for CRL32102)

(2 for CRL32202)

(3 for CRL32302/CRL32352)

(4 for CRL32452)

Battery for cordless handset

(1 for CRL32102)

(2 for CRL32202)

(3 for CRL32302/CRL32352)

(4 for CRL32452)

Battery compartment cover

(1 for CRL32102)

(2 for CRL32202)

(3 for CRL32302/CRL32352)

(4 for CRL32452)

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V 400mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR0920

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Telephone line cord

Abridged user’s manual

CRL32102/CRL32202/

CRL32302/CRL32352/CRL32452

DECT 6.0 cordless telephone/

answering system with

caller ID/call waiting

Telephone base installation

If you have DSL

high-speed Internet

service, a DSL filter (not

included) is required.

The DSL filter must

be plugged into the

telephone wall jack.

This quick start guide provides you with basic instructions only.

For more complete instructions, refer to your Abridged user’s

manual provided in the package, or see the online Complete

user’s manual at www.telephones.att.com/manuals.

Plug the power

adapter into an

electrical outlet

not controlled by a

wall switch.

Charger installation

Quick start guide

CRL32102/CRL32202/CRL32302/CRL32352/CRL32452

Plug the power

cord and telephone

line cord into

the jacks.

Route the

cords through

the slots.

Plug the other end of the

telephone line cord into a

telephone jack or a DSL filter.

Caution: Use only the power adapter provided with this product. To obtain a replacement, visit

our website at www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

Abridged user’s manual

CRL32102/CRL32202/CRL32302/

CRL32352/CRL32452

DECT 6.0 cordless telephone/

answering system with

caller ID/call waiting

Getting started

Quick reference guide - handset ........1

Quick reference guide -

telephone base ......................................2

Telephone base and charger

installation ...............................................3

Telephone base installation ............3

Charger installation .............................3

Battery installation and charging ....... 4

Installation options .................................... 6

Tabletop to wall-mount

installation.............................................6

Telephone settings

Handset settings .........................................7

Ringer volume ........................................7

Ringer tone .............................................. 7

LCD language .........................................7

Set date/time ......................................... 8

Caller ID announce ..............................8

Set speed dial voicemail number ....9

Voicemail (visual message

waiting) indicator ...............................9

Clear voicemail indicator ..................9

Key tone ................................................. 10

Home area code ................................. 10

Dial mode .............................................. 10

QUIET mode ......................................... 11

Telephone operation

Handset operation .................................. 12

Making a call ........................................ 12

Answering a call ................................ 12

Ending a call ........................................ 12

Temporary ringer silencing ........... 12

Speakerphone ..................................... 12

Last number redial ............................ 12

Equalizer ................................................. 12

Volume control ................................... 13

Call waiting ........................................... 13

Mute ......................................................... 13

Handset locator .................................. 13

Join a call in progress ..................... 13

Chain dialing ........................................ 14

Blind transfer ....................................... 14

Multiple handset use

Intercom call .............................................. 15

Call transfer using intercom .............. 16

Directory

Directory ...................................................... 17

Create a new directory entry ...... 17

Review directory entries ................ 18

Search by name.................................. 18

Delete a directory entry ................. 18

Edit a directory entry ....................... 18

Table of contents

For more detailed instructions, refer to the Complete user’s

manual at www.telephones.att.com/manuals.

Speed dial .................................................. 19

Assign a speed dial number......... 19

Assign your speed dial

voicemail number ........................... 19

Make a call using speed dial ....... 19

Check your voicemail using

speed dial ........................................... 19

Caller ID

Caller ID ....................................................... 20

Information about caller ID

with call waiting .............................. 20

Missed (new) call indicator ........... 20

Review the caller ID log ................. 20

Dial a caller ID log entry ............... 20

View dialing options ......................... 20

Save a caller ID log entry to the

directory ................................................. 21

Answering system

Answering system settings ................. 22

Announcement ................................... 22

Answer on/off ..................................... 23

Call screening ...................................... 23

Number of rings ................................. 24

Remote access code ........................ 24

Message alert tone ........................... 25

Message recording time ................. 25

About the answering system............. 26

Answering system and

voicemail indicators.......................... 26

Using the answering machine

and voicemail together .................. 26

Message capacity .............................. 27

Voice prompts ..................................... 27

Call screening at the

telephone base ................................... 27

Call screening at the handset ..... 27

Call intercept ....................................... 27

Temporarily turning off the

message alert tone ........................... 27

Message playback ................................... 28

Options during playback ................ 28

Delete all old messages ................. 29

Recording and playing memos ......... 29

Record a memo .................................. 29

Play back a memo ............................ 29

Remote access .......................................... 30

Appendix

Adding and registering

handsets/headsets ................................. 31

Register a handset to your

telephone base ................................... 31

Deregistering handsets ........................ 32

Deregister all handsets from

your telephone base ........................ 32

Troubleshooting ....................................... 33

Maintenance............................................... 36

Important safety information ............ 37

Safety information ............................. 37

Especially about cordless

telephones ............................................ 38

Precautions for users of

implanted cardiac pacemakers ... 38

Pacemaker patients .......................... 38

Especially about telephone

answering systems ......................... 38

For C-UL compliance ............................. 39

Mesures de sécurité

importantes ......................................... 39

FCC Part 68 and ACTA .......................... 42

FCC Part 15 ................................................ 43

Limited warranty ...................................... 44

Technical specifications ....................... 46

DECT 6.0 digital technology ......... 46

Telephone operating range .......... 46

HD audio ................................................ 46

Index

Index .............................................................. 47

1

Quick reference guide - handset

Getting started

Audio Assist is a registered trademark of Advanced American Telephones.

CHARGE indicator

On when the handset is

charging in the telephone base

or charger.

qCID/VOLUME

Press qCID to show the

caller ID log (page 20).

Press to scroll down while

in menus.

While entering names or

numbers, press to move the

cursor to the left.

Press to decrease the listening

volume when on a call, or to

decrease the message playback

volume (page 28).

PHONE/FLASH

Press to make or answer a call.

During a call, press to answer an

incoming call when you receive

a call waiting alert (page 13).

1

While reviewing a caller ID

log entry, press repeatedly to

add or remove 1 in front of

the telephone number before

dialing or saving it in the

directory (page 20).

Press and hold to set (page 9)

or dial your voicemail number

(page 19) when the handset is

not in use.

MUTE/DELETE

During a call, press to mute the microphone.

While reviewing the caller ID log, the directory

or the redial memory, press to delete an

individual entry.

While predialing, press to delete digits.

While editing numbers or names in the

directory, press to delete digits or characters, or

press and hold to delete all digits or characters.

/SPEA�ERSPEA�ER

Press to switch between the

speakerphone and the handset

(page 12).

QUIET

#

(pound key)

Press repeatedly to display

other dialing options when

reviewing a caller ID log entry

(page 20).

Press and hold to enter the

QUIET mode setting screen,

or to deactivate QUIET mode

(page 11).

OFF/CANCELOFF/CANCEL

During a call, press to hang up.

While in menus, press to cancel

an operation, back up to the

previous menu, or exit the

menu display; or press and hold

this key to exit to idle mode.

Press and hold while the

telephone is not in use to erase

the missed call indicator.

MENU/SELECT

Press to show the menu.

While in the menu, press to

select an item or save an entry

or setting.

pDIR/VOLUME

Press pDIR to show directory

entries (page 18).

Press to scroll up while in menus.

While entering names or

numbers, press to move the

cursor to the right.

Press to increase the listening

volume when on a call (page 13),

or to increase the message

playback volume (page 28).

TONE

Press to switch to touch-tone

dialing temporarily during a call

if you have pulse service.

REDIAL/PAUSE

Press repeatedly to view

the last 10 numbers dialed

(page 12).

While saving numbers into the

directory,

press and hold

to

insert a dialing pause (page 17).

AUDIO ASSIST

During a call, press to enhance

the clarity and loudness of your

caller’s voice.

Incoming call light

Flashes when there is an incoming call or

when the base is paging the handset.

2

Getting started

Quick reference guide - handset

EQ

During an outside call, intercom call, message

or announcement playback, press to change

the quality of the audio to best suit your

hearing (page 12).

Handset

side view

Quick reference guide - telephone base- telephone base

IN USE indicator

On when the handset is in use, or when the

answering system is answering an incoming call.

On when a handset is being registered.

Flashes when there is an incoming call or

when handsets are being deregistered.

Flashes when another telephone is in use on

the same line.

/PLAY/STOP

Press to start or

stop message

playback (page 28).

/S�IP

Press to skip a

message (page 28).

/REPEAT

Press to repeat a

message.

Press twice to

play the previous

message (page 28).

X/DELETE

Press to delete the message currently playing

(page 28).

Press twice to delete all old messages when the

phone is not in use (page 29).

/ANS ON

Press to turn the built-in answering

system on or off (page 23).

VOLq and VOLp

During message

playback, press to

adjust the listening

volume (page 28).

While in idle mode,

press to adjust the

base ringer volume.

/HANDSET LOCATOR

While the phone is idle, press to

page all handsets (page 13).

Incoming call light

Flashes when there is an

incoming call.

SLOW

Press to slow

down the message

playback (page 28).

Message counter

Shows the number

of messages or other

answering system

information.

Shows the base ringer

volume or playing

message volume.

Getting started

3

Telephone base and charger installation

Install the telephone base and charger, as shown below.

IMPORTANT INFORMATION

Use only the power adapter(s) supplied with this product. To order a replacement

power adapter, visit our website at www.telephones.att.com or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

For more detailed instructions, refer to the online Complete user’s manual at

www.telephones.att.com/manuals.

The power adapters are intended to be correctly oriented in a vertical or floor

mount position. The prongs are not designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or cabinet outlet.

1.

2.

Charger installation

Telephone base installation

Plug the large end of the

charger power adapter into an

electrical outlet not controlled

by a wall switch.

Telephone line cord

A DSL filter (not included)

is required if you have

DSL high-speed Internet

service. The DSL filter

must be plugged into the

telephone wall jack.

Plug the small end of

the telephone base

power adapter into the

power jack on the back

of the telephone base.

Plug the large end of

the telephone base

power adapter into an

electrical outlet not

controlled by a wall

switch.

Plug the other end

of the telephone line

cord into the TEL. LINE

jack on the back of the

telephone base.

Plug one end of the

telephone line cord

into a telephone jack

or a DSL filter.

Route the cords

through the channels.

Telephone base

Charger

4

Getting started

Battery installation and charging

Once you have installed the battery, the screen indicates the battery status

(see the following table). For best performance, keep the handset in the

telephone base or charger when not in use. The battery is fully charged

after 10 hours of continuous charging. See the table in the Technical

specifications section on page 46 for battery operating times.

Battery indicators Battery status Action

The screen is blank, or

shows Place in charger

and (flashing).

Battery has no or

very little charge. The

handset cannot be used.

Charge without interruption

(at least 30 minutes).

The screen shows

Low battery and

(flashing).

Battery has enough

charge to be used for a

short time.

Charge without interruption

(at least 30 minutes).

The screen shows

HANDSET X.

Battery is charged. To keep the battery charged, place it in the

telephone base or charger when not in use.

1. Plug the battery connector securely into the socket inside the handset

battery compartment. Insert the supplied battery with the label

THIS SIDE UP facing up, as indicated.

2. Align the cover flat against the battery compartment, then slide it upwards

until it clicks into place.

HD

A

UDI

O

T

HI

S

SI

DE

U

P

/ CE

CÔ

T

É

V

E

RS

L

E

HA

U

T

Ba

tt

e

r

y Pa

c

k

/ Bl

o

c

-

pi

l

e

s

:

BT18

3

34

2

(2

.4

V

4

0

m

A

h

Ni

-M

H

)

W

AR

NI

N

G

/

AV

ER

T

IS

S

EM

ENT

:

DO

N

OT

BU

R

N

O

R

P

UN

CT

U

RE

BA

TT

E

R

I

ES.

NE

PA

S

I

N

CI

N

ÉR

E

R

O

U PER

CER

L

E

S PI

LE

S.

Ma

d

e

i

n

C

h

in

a

/

F

a

br

i

qu

é

e

n

ch

i

ne

HD

A

UDI

O

H

D

A

UD

IO

Getting started

5

Battery installation and charging

3. Charge the handset by placing it face forward

in the telephone base or charger. The CHARGE

light on the handset is on during charging.

IMPORTANT INFORMATION

1. Use only the supplied rechargeable battery or replacement battery (model

BT183342/BT283342). To order, visit our website at

www.telephones.att.com or

call 1 (800) 222-3111. In Canada,

dial 1 (866) 288-4268. For more detailed instructions, refer to the online

Complete user’s manual at www.telephones.att.com/manuals.

2. If you do not use the handset for a long time, disconnect and remove the battery to

prevent possible leakage.

CHARGE light

6

Getting started

Installation options

Your telephone base is ready for tabletop use. If you want to mount your

telephone on a wall, use the provided wall-mount bracket to connect with

a standard dual-stud telephone wall-mounting plate. If you do not have this

mounting plate, you can purchase one from many hardware or consumer

electronics retailers. You might need a professional to install the mounting plate.

Tabletop to wall-mount installation

With the upper tabs (marked A) on top, align the holes of the wall-mount

bracket with the studs on the standard wall-mounting plate and slide the

bracket down until it locks securely.

Plug one end of the telephone line cord into the jack on the bottom of the

telephone base and plug the other end into the telephone wall jack (or

DSL filter). Plug the small end of the telephone base power adapter into

the jack on the bottom of the telephone base and plug the other end into

an electrical outlet not controlled by a wall switch. Route the telephone

line cord and the power cord through the grooves at the bottom of the

telephone base, accordingly.

Hold the cords to the side of the telephone base. Align the upper slots

on the back of the telephone base just above the upper tabs (marked A)

of the wall-mount bracket. Make sure the lower slots of the telephone

base are also aligned above the lower tabs (marked B) of the wall-mount

bracket. Push the telephone base down until it clicks securely in place.

Bundle the telephone line cord and power adapter cord neatly with twist ties.

1.

2.

3.

4.

1

2

4

3

7

Telephone settings

Handset settings

Use the menu to change the telephone settings.

Press MENU/SELECT when the telephone is not in use to enter the

main menu.

Press qCID or pDIR to scroll to the feature to be changed. When scrolling

through the menu, the > symbol indicates the highlighted menu item.

Press MENU/SELECT to select the highlighted item.

NOTE: Press OFF/CANCEL to cancel an operation, back up to the previous menu or

exit the menu display. Press and hold OFF/CANCEL to return to idle mode.

Ringer volume

You can adjust the ringer volume level or turn the ringer off.

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Ringers, then press MENU/SELECT.

3. Press MENU/SELECT again to select >Ringer volume.

4. Press qCID or pDIR to sample each volume level.

5. Press MENU/SELECT to save your preference.

NOTE: The handset ringer volume also determines the ringer volume for intercom calls.

Ringer tone

You can choose one of 10 ringer tones.

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Ringers, then press MENU/SELECT.

3. Press qCID or pDIR to scroll to >Ringer tone, then press MENU/SELECT.

4. Press qCID or pDIR to sample each ringer tone.

5. Press MENU/SELECT to save your preference.

NOTE: If you turn off the ringer volume, you do not hear ringer tone samples.

LCD language

You can select English, French, or Spanish to be used for all screen displays.

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press MENU/SELECT.

3. Press MENU/SELECT to choose >LCD language.

4. Press qCID or pDIR to scroll to the desired language, then press

MENU/SELECT. The screen prompts Set English/Français/Español as

LCD language?.

5. Press MENU/SELECT to confirm.

1.

2.

3.

Telephone settings

8

Handset settings

NOTE: If you accidentally change the LCD language to French or Spanish, you can reset it

back to English without going through the French or Spanish menus. Press MENU/SELECT

in idle mode, then enter 364#. There is a confirmation tone.

Set date/time

The answering system announces the day and time of each message prior

to playing it. Before using the answering system, set the date and time as

follows. If you subscribe to caller ID service, the day, month and time are

set automatically with each incoming call. The year must be set so that the

day of the week can be calculated from the caller ID information.

When the handset is in idle mode, press MENU/SELECT to enter the main menu.

Press qCID or pDIR to scroll to >Set date/time and then press MENU/SELECT.

Enter the month using the dialing keys.

Enter the day using the dialing keys.

Enter the year using the dialing keys, then press MENU/SELECT to move on

to set the time.

Enter the hour using the dialing keys.

Enter the minute using the dialing keys.

Press qCID or pDIR to highlight AM or PM, then press MENU/SELECT to confirm.

NOTE: If the clock is not set when a message is recorded, the system announces, “Time and

day not set,” before it plays the message.

Caller ID announce

The caller ID announce feature lets you know who’s calling without having to

look at the display.

To turn on/off the caller ID announce feature on your handset or base:

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press MENU/SELECT.

3. Use qCID or pDIR to scroll to >Caller ID annc, then press MENU/SELECT.

4. Use qCID or pDIR to highlight the desired option, then press MENU/SELECT.

Set all On/Off - Change the setting for the base and all handsets.

Local handset - Change the setting for that handset only.

Base - Change the setting for the telephone base only.

5. Use qCID or pDIR to highlight >On or >Off, then press MENU/SELECT.

NOTES:

To use the caller ID announce feature, you must subscribe to caller ID service from your

telephone service provider.

Pronunciation of names may vary with this feature. Not all names may be pronounced correctly.

1.

2.

3.

4.

5.

6.

7.

8.

•

9

Telephone settings

Handset settings

Set speed dial voicemail number

This feature lets you save your voicemail number for quick access when you

press and hold the 1 key.

To set your voicemail number:

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press MENU/SELECT.

3. Use qCID or pDIR to scroll to >Voicemail #, then press MENU/SELECT.

4. Use the dialing keys to enter the voicemail access number provided by

your telephone service provider.

Press qCID or pDIR to move the cursor to the left or right.

Press MUTE/DELETE to erase a digit.

Press and hold MUTE/DELETE to erase all digits.

Press REDIAL/PAUSE to enter a three-second dialing pause (a p appears).

5. Press MENU/SELECT to save.

Voicemail (visual message waiting) indicator

If you subscribe to a voicemail service offered by your telephone service

provider, New voicemail and the icon appear on the handset screen when

you have new voicemail messages. Contact your service provider for more

information and assistance about using your voicemail service.

Clear voicemail indicator

Use this feature when the telephone indicates there is new voicemail but

there is none. For example, when you have accessed your voicemail while

away from home. This feature only turns off the displayed New voicemail

and the icon; it does not delete your voicemail messages. As long as you

have new voicemail messages, your telephone service provider continues to

send the signal to turn on the indicator.

To manually turn off the new voicemail indicator:

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press MENU/SELECT.

3. Use qCID or pDIR to scroll to >Clr voicemail, then press MENU/SELECT.

The screen shows Reset Voicemail Indicator?.

4. Press MENU/SELECT again to turn the voicemail indicator off.

NOTE: For information about using your voicemail service, contact your telephone

service provider.

•

Telephone settings

10

Handset settings

�ey tone

The handset is set to beep with each key press. You can adjust the key tone

volume or turn it off.

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press MENU/SELECT.

3. Use qCID or pDIR to scroll to >�ey tone, then press MENU/SELECT.

4. Use qCID or pDIR to select the desired volume or Off.

5. Press MENU/SELECT to save your preference.

Home area code

If you dial seven digits to make a local call (no area code required), enter your area

code into the telephone as the home area code. When you receive a call from

within your home area code, the caller ID log only displays the seven digits of the

telephone number.

This feature makes it easy for you to place a call from the caller ID log. If you

dial 10 digits to make a local phone call, do not use this home area code

feature. If you do, you cannot place local calls from your caller ID log, as they

will have only seven digits.

To set the home area code:

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press MENU/SELECT.

3. Use qCID or pDIR to scroll to >Home area code, then press MENU/SELECT.

4. Use the dialing keys to enter a three-digit home area code.

Press MUTE/DELETE to delete a digit.

Press and hold MUTE/DELETE to delete all digits.

5. Press MENU/SELECT to save.

NOTE: If in the future, your telephone service provider requires you to dial 10 digits to

make a local call (area code plus telephone number), you need to delete your home

area code and dial out locally from the caller ID log. With the home area code displayed,

press and hold MUTE/DELETE until the digits are deleted, and then press MENU/SELECT.

The home area code is now restored to its default setting of _ _ _ (empty).

Dial mode

The dial mode is preset to tone dialing. If you have pulse (rotary) service, you

must change the dial mode to pulse dialing before using the telephone.

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press MENU/SELECT.

3. Use qCID or pDIR to scroll to >Dial mode, then press MENU/SELECT.

4. Use qCID or pDIR to highlight >Touch-tone or >Pulse, then, press

MENU/SELECT.

•

11

Telephone settings

Handset settings

QUIET mode

When QUIET mode is turned on, the telephone silences all sounds (except the

handset locator paging tone) during the set period of time (1-12 hours). After

you turn on QUIET mode, this feature activates immediately and the answering

system turns on automatically. When QUIET mode is on, the answering system

takes calls and records messages without broadcasting them.

To turn QUIET mode on:

Press and hold QUIET

#

when the handset is not in use.

Using the dialing keys (0-9) to enter the duration, then press SELECT

to save.

To turn QUIET mode off:

Press and hold QUIET

#

when the handset is not in use.

NOTES:

If you change the base ringer, handset ringer, ringer volume, key tone, or caller ID

announce features when QUIET mode is on, the sample plays but the feature is still

muted after saving the setting.

After QUIET mode is turned off or the set period of time has expired, all muted

features will be activated again.

Intercom is available during QUIET mode, but the handset will not ring.

1.

2.

•

Telephone operation

12

Handset operation

Making a call

Press PHONE/FLASH or /SPEA�ERSPEA�ER, then enter the telephone number.

Answering a call

Press PHONE/FLASH or /SPEA�ERSPEA�ER.

-OR-

Press any dialing key (0-9, TONE or #).

Ending a call

Press OFF/CANCEL or return the handset to the telephone base or charger.

Temporary ringer silencing

Press OFF/CANCEL or MUTE/DELETE while the telephone is ringing to

silence the ringer temporarily on that handset only. This turns off the ringer

without disconnecting the call. The next incoming call rings normally at the

preset volume.

Speakerphone

During a call, press /SPEA�ERSPEA�ER to switch between handsfree speakerphone

and normal handset use. Press OFF/CANCEL to hang up.

NOTE: The speakerphone uses more power than the normal handset. If the handset battery

becomes very low while you are using the speakerphone, the call remains in speakerphone

mode until you hang up or the battery becomes depleted.

Last number redial

Each handset stores the last 10 telephone numbers dialed (up to 30 digits).

Press REDIAL/PAUSE, then press qCID or pDIR, or press REDIAL/PAUSE

repeatedly to view up to 10 recently called numbers. Press PHONE/FLASH

or /SPEA�ERSPEA�ER to dial the displayed number.

Equalizer

The equalizer feature on the handset enables you to change the quality of

the audio to best suit your hearing.

While on a call or intercom call, or listening to a message or announcement,

press EQ to select the equalizer setting Treble 1, Treble 2, Bass or

Natural (the default setting).

•

Telephone operation

13

Handset operation

Volume control

While on a call, press qCID/VOLUME to decrease or press pDIR/VOLUME

to increase the listening volume. You can set the listening volume to one of

six levels.

Call waiting

If you subscribe to call waiting service from your telephone service provider,

and someone calls while you are already on a call, you hear two beeps. Press

PHONE/FLASH to put your current call on hold and take the new call.

Press PHONE/FLASH at any time to switch back and forth between calls.

Mute

The mute function allows you to hear the other party, but the other party

cannot hear you.

Press MUTE/DELETE while on a call to enable or disable the mute feature.

Handset locator

Use this feature to find misplaced handsets.

To start the paging tone:

Press /HANDSET LOCATOR on the telephone base to start the paging

tone on all handsets for 60 seconds.

NOTE: If you press OFF/CANCEL or MUTE/DELETE on a handset, the ringer of that

handset stops, but the paging to the rest of the handsets continues.

To stop the paging tone:

Press PHONE/FLASH, /SPEA�ERSPEA�ER, or any dialing key (0-9, TONE , or #)

on the handset(s).

-OR-

Press /HANDSET LOCATOR on the telephone base.

Join a call in progress

When a handset is already on a call and you would like to join the call, press

PHONE/FLASH or /SPEA�ERSPEA�ER on your handset.

Press OFF/CANCEL or place the handset in the telephone base or charger to

end the call. The call does not end until all handsets hang up.

NOTE: You can use a maximum of 4 system handsets at the same time on an outside call.

•

Telephone operation

14

Options while on calls

Chain dialing

Use this feature to initiate a dialing sequence from the numbers in the

directory, caller ID log or redial memory while you are on a call.

To access the directory or caller ID log while on a call:

Press MENU/SELECT.

Press qCID or pDIR to scroll to >Directory or >Caller ID log, then press

MENU/SELECT.

Press qCID or pDIR to scroll to the desired number.

Press MENU/SELECT to dial the number shown.

To access the redial list while on a call:

Press REDIAL/PAUSE to show the most recently dialed number.

Press qCID or pDIR to scroll to the desired number, or press REDIAL/PAUSE

repeatedly to show the last 10 recently dialed numbers. Then, press

MENU/SELECT to dial the number shown.

Blind transfer

While on an outside call, you can transfer it to a specific handset or any

handset. This feature is not available for model CRL32102 unless you

purchase an accessory handset (AT&T model CRL30102).

To transfer an outside call directly without notifying the desired handset:

1. During the call, press MENU/SELECT.

2. Press MENU/SELECT to choose >Transfer.

If you have a 2-handset system, the outside call is put on hold and your

handset screen shows Transferring call.... The other handset rings and

its screen shows Transfer from other handset.

If you have more than 2 handsets, your screen shows TRANSFER TO:.

Press qCID or pDIR to scroll to the desired handset and press

MENU/SELECT. The outside call is put on hold and your handset screen

shows Transferring call... or Transferring call to all....

3. To answer the call on the destination handset, press, press PHONE/FLASH or

/SPEA�ERSPEA�ER. The original handset shows Call transferred and goes to

idle mode.

1.

2.

3.

4.

1.

2.

•

Multiple handset use

15

Intercom call

Use the intercom call feature for conversations between two handsets. This

feature is only available if you have at least two system handsets. Intercom

call is not available for the CRL32102 model. You can buy accessory

handsets (AT&T model CRL30102) to expand your system.

Use a handset to initiate intercom calls and transfer calls.

1. Press MENU/SELECT in idle mode to enter the main menu. Press qCID or

pDIR to scroll to >Intercom, then press MENU/SELECT. Choose from the

following options.

If you have a two-handset system, your handset screen shows

Calling other handset.

If you have more than two handsets, your screen shows INTERCOM TO:.

Press qCID or pDIR to scroll to the desired handset and press

MENU/SELECT. Your handset screen shows Calling HANDSET X or

Calling all handsets.

The other handset(s) rings and shows either Other handset is calling

or HANDSET X is calling (HANDSET represents the handset name, X

represents the handset number).

2. To answer the intercom call, press PHONE/FLASH, /SPEA�ERSPEA�ER or any

dialing key (0-9, TONE , or

#

) on any called handset.

3. To end the intercom call, one party presses OFF/CANCEL, or places the

handset back in the telephone base or charger. The other party hears four

beeps. Both handsets display Intercom ended.

•

La page charge ...

AT&T CRL32102 Manuel utilisateur

Ce manuel convient également à

AT&T CRL32102 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents