BADU Variostar Mode d'emploi

  • Bonjour, je suis votre assistant virtuel et j'ai examiné la fiche technique de la pompe BADU Variostar. Je comprends donc ses capacités, ses paramètres de fonctionnement, son contrôle et ses options d'installation. N'hésitez pas à me poser vos questions.
  • Comment activer la vitesse du moteur?
    La pompe a-t-elle un mode de dégagement d'air?
    Comment modifier les paramètres?
10|2021
DE Pumpendatenblatt
EN Pump data sheet
FR Fiche technique pompe
NL Pompgegevens
IT Documentazione pompa
ES Ficha técnica de la bomba
Variostar
VW21.08.700-P
2 10|2021
SPECK Pumpen Verkaufsgesellschaft GmbH
Hauptstraße 3
91233 Neunkirchen am Sand, Germany
Telefon 09123 949-0
Telefax 09123 949-260
info@speck-pumps.com
www.speck-pumps.com
Alle Rechte vorbehalten.
Inhalte dürfen ohne schriftliche Zustimmung von SPECK Pumpen
Verkaufsgesellschaft GmbH weder verbreitet, vervielfältigt, bearbeitet
noch an Dritte weitergegeben werden.
Dieses Dokument sowie alle Dokumente im Anhang unterliegen keinem
Änderungsdienst!
Technische Änderungen vorbehalten!
10|2021 3
71
90
110
114
7
95
145
112
274,5
225
219 Ø142
200
343
350
max. L
344
Da
Sa
VW21.08.700-P
0510 15 20 25 30 35 40 45 50 55 60 65 70
Q [m³/h]
KL21.08.700-P
2
4
6
8
H [m]
1800 min
-1
1500 min
-1
1100 min
-1
600 min
-1
4 10|2021
Sa [mm]
Da [mm]
d-Saug
[mm]
d-
Druck
[mm]
max. L
[mm]
90
90
110
110
543
1~ 230 V
n [min
-1]
P1 [kW]
P2 [kW]
I [A]
Lpa
(1m)
[dB(A)]
Lwa
[dB(A)]
m [kg]
WSK/PTC
600
0,07
0,03
0,60
40,2
48
12
●/○
1800
1,15
0,85
4,95
57,6
66
12
●/○
n [min
-1]
Hmax. [m]
SP
Hs [m]
Hz [m]
IP
W-Kl
T [°C]
P-GHI
[bar max.]
600
0,80
-
3
55
F
40(60)
2,5
1800
6,90
-
3
55
F
40(60)
2,5
10|2021 DE 5
DE Pumpendatenblatt
Mitgeltende Dokumente
Zu diesem Pumpendatenblatt gehört die
Originalbetriebsanleitung "Normal- und selbstansaugende
Pumpen mit/ohne Kunststofflaternen-Ausführung (-AK)". Sie
muss für das Bedien- und Wartungspersonal frei zugänglich
sein.
Variostar
VW21.08.700-P
DE 6 10|2021
Glossar
TD
Technische Daten
Sa
Sauganschluss
Da
Druckanschluss
d-Saug
Empfohlener Durchmesser der Saugleitung bis 5 m
d-Druck
Empfohlener Durchmesser der Druckleitung bis 5 m
max. L
Maximale Länge der Pumpe
D
Dichte
P1
Aufgenommene Leistung
P2
Abgegebene Leistung
I
Nennstrom
Lpa (1 m)
Schalldruckpegel in 1 m Entfernung gemessen nach DIN 45635
Lwa
Schallleistung
m
Gewicht
WSK
Wicklungsschutzkontakt oder Motorschutzschalter
PTC
Kaltleiter
Hmax.
Maximale Förderhöhe
SP
Selbstansaugend
Hs; Hz
Geodätische Höhe zwischen Wasserspiegel und Pumpe
Hs
Maximale Saughöhe
Hz
Maximale Höhe bei Zulaufbetrieb
IP
Schutzart des Motors
W-Kl
Wärmeklasse
n
Drehzahl
P-GHI
2,5 bar max. Gehäuseinnendruck/max. Systemdruck
T
Wassertemperatur
Ja
Nein
T/°C
Erläuterung Wassertemperatur 40 °C (60 °C): 40 °C = gilt für
maximale Wassertemperatur im Sinne des GS-Zeichens. (60 °C) =
Pumpe ist ohne weiteres für eine maximale Wassertemperatur von
60 °C einsetzbar/ausgelegt.
1~/3~
Geeignet für Dauerbetrieb bei
1~ 220 - 240 V ± 5%
3~ Y/∆ 380 - 420 V/220 - 240 V ± 5%
3~ Y/∆ 660 - 725 V/380 - 420 V ± 5%
Für Normspannung geeignet nach DIN IEC 60038; DIN EN 60034
10|2021 DE 7
Die Pumpe besitzt einen Permanentmagnet-Motor und ist elektronisch vor
Überlastung gesichert.
Anschluss externer Schaltkontakte
Zur externen Ansteuerung besitzt die Pumpe ein 8-adriges Kabel mit
offenen Enden. Zuordnung der Kabel zu den einzelnen Drehzahlen wie
folgt:
Die Kabel sind potentialfrei anzuschließen. Kontakte nur einzeln
schalten (Priorität der Kontakte beachten), ansonsten erfolgt keine
Aktivierung der gewünschten Drehzahl.
WG27.50.135-1-P
Blau
Grün
Gelb
Rot
Schwarz
Orange
Violett
Braun
= GND-Analog
= n 1
= n 2
= n 3
= Stopp
= GND-Digital
= Analog 0 - 10 V
= Analog 4 - 20 mA
Priorität
Niedrig
n1
Hoch
Stopp
WG27.50.094-1-P
n2 n3
DE 8 10|2021
HINWEIS
Einschalten der Motordrehzahl mittels Handtaster oder externer
Schaltkontakte. Dadurch
Aktivierung der Schaltkontakte und der
zugeordneten Drehzahl.
Im laufenden Betrieb werden die Festdrehzahlen direkt angefahren, ohne
Entlüftungszeit.
Wird die externe Ansteuerung nicht benötigt, müssen die Kabelenden
isoliert werden.
HINWEIS
Für das problemlose Zusammenspiel mit Peripheriegeräten, wie z.B.
Elektrowärmetauscher oder Dosieranlagen, wird der Einbau eines
Strömungswächters mit entsprechender Auswerteeinheit empfohlen.
Damit kann auch eine Störmeldung ausgegeben werden.
0 1 23 4 5 6 78 9 10 11 12 1413 15 16 17 18 19 20 21
200
400
600
800
1000
1200
1400
1600
1800
2000
n [min
-1
]
l [mA]
0 1 23 4 5 6 7 8 9 10 11
U [V]
200
400
600
800
1000
1200
1400
1600
1800
2000
n [min
-1
]
10|2021 DE 9
HINWEIS
Um Fehlfunktionen im Motor zu vermeiden, müssen folgende Punkte
unbedingt beachtet werden:
Die Steuerleitung muss fachlich korrekt verlegt werden. Eine
Montage parallel zur eigenen Netzleitung oder
anderen Verbrauchern
muss vermieden werden.
Sollten die Steuerleitungen verlängert werden, können gefährliche
Spannungen am Digitaleingang entstehen. Diese müssen zum
Beispiel durch Abschirmung verhindert werden.
Die Netzkabel verschiedener Betriebsmittel nicht am gleichen
Versorgungsstrang betreiben.
Voreinstellung:
Geschwindigkeit:
Entlüftungsgeschwindigkeit:
Entlüftungszeit:
Einstellbare Geschwindigkeit:
Einstellbare Entlüftungszeit:
Externe Ansteuerung:
Schaltverhalten Eingang „0“:
1 = 600 min-1
2 = 1100 min-1
3 = 1800 min-1
= 1800 min-1
= oFF
600 1800 min-1 (in 10 min-1 Schritten)
oFF, 1 10 Min. (in 1 Min. Schritten)
oFF
0 cl
Bedienoberfläche:
(1) LED-Display: zeigt die aktuelle Drehzahl
des Motors an.
(2) : Auswahl der voreingestellten
Drehzahlen
(3) : Zur Anzeige des aktuellen
Verbrauchs und Auswahl der
Parameter im Setup
(4) : Zum Einstellen der Parameter
(5) : zum Ändern der Drehzahl
(6) : zum Stoppen des Motors
Beim Zuschalten der Netzspannung erscheint kurzzeitig im Display die
Softwareversion "-rX.X-"
WG27.50.136-P
4
6
5
1
2
3
DE 10 10|2021
Bedienung:
Taste oder drücken, um die voreingestellte
Drehzahl auszuwählen.
Die Pumpe ist nach Werkseinstellung ohne
Entlüftungszeit programmiert.
Wird die Entlüftungsphase der Pumpe aktiviert,
wandert an der ersten Stelle im Display ein Balken von
der unteren, über die mittlere zur oberen Position.
Im laufenden Betrieb werden die Drehzahlen direkt
angefahren, ohne Entlüftungszeit.
Durch Drücken der Taste wird der Motor gestoppt.
Die "Power"-LED blinkt und das Display zeigt "oFF"
an.
Ist in den Parametern eine analoge Ansteuerung
eingestellt, kann mit der Taste der Motor wieder
gestartet werden.
Einstellen der Drehzahlen:
Die Taste der Festdrehzahl die verändert werden soll
drücken ( oder ) und danach mit den Tasten
die Drehzahl ändern. Die eingestellte Drehzahl
wird direkt gespeichert und bei erneuter Auswahl der
Festdrehzahl angefahren.
Hinweis: Während der Entlüftungsphase kann die Drehzahl nicht
verändert werden.
Einstellen der Parameter:
Durch Drücken der Taste für 3 Sekunden wird in
das Setup-Menü gewechselt. Dort kann mit der -
Taste durch das Menü geblättert werden.
Die erste Stelle des Displays zeigt den aktuellen
Menüpunkt an und die restlichen vier Stellen den
einzustellenden Parameter.
Wird die Taste innerhalb des Menüs gedrückt, dann
werden alle geänderten Werte gespeichert und das
Setup-Menü verlassen, der Text "StorE" wird im
Display angezeigt.
Durch Drücken der Taste wird das Setup-Me
ohne Speicherung der geänderten Werte verlassen.
WG27.50.137-P
WG27.50.138-P
WG27.50.009-P
10|2021 DE 11
Ansaugparameter:
Unter dem Menüpunkt "n" wird die Drehzahl und unter
dem Punkt "t" wird die Zeit während der
Entlüftungsphase eingestellt.
"t oFF" = keine Entlüftungsphase
von oFF, 1 - 10 Minuten
Digitaleingänge/Analogeingänge:
Bei dem Menüpunkt "E" kann die externe
Ansteuerung aktiviert bzw. deaktiviert werden.
"oFF" = deaktiviert
"dl" = Digitaleingänge (potentialfrei) aktiviert
"Uin" = Analogeingang (potentialfrei) 0-10 V
"lin" = Analogeingang (potentialfrei) 4-20 mA
Schaltverhalten "0" (Stopp):
Unter dem Punkt "0" kann das Schaltverhalten des
Digitaleingangs "0" (Stopp) geändert werden.
"cL" bedeutet, der Antrieb wird bei geschlossenem
Stopp-Kontakt gestoppt.
"oP" bedeutet, der Antrieb wird bei offenem Stopp-
Kontakt gestoppt.
"not" bedeutet, der externe Kontakt zum Stoppen wird
nicht benötigt. Öffnen des GND-Kontaktes stoppt den
Antrieb.
Zurücksetzen / Reset:
Wird die -Taste für mindestens 10 Sekunden
gedrückt, dann wird der Antrieb auf die
Werkseinstellungen zurückgesetzt. Der Motor stoppt
und im Display steht "rESEt".
Durch Drücken der -Taste wird im Display der
aktuelle Leistungsbedarf der Pumpe in Watt angezeigt
(P XXX).
Das Display der Steuerung schaltet sich nach drei
Minuten ohne Aktion ab.
Die Pumpe läuft nach einem Spannungsverlust automatisch wieder mit
der zuletzt eingestellten Drehzahl an oder bleibt stehen, wenn sie zuvor
gestoppt wurde.
WG27.50.011-P
WG27.50.012-P
WG27.50.013-P
WG27.50.014-P
DE 12 10|2021
Das Ein- und Ausschalten der Pumpe sollte über das dafür vorgesehene
Steuerkabel (potentialfreie Kontakte) realisiert werden. Dies kann über
eine BADU-Logic-Steuerung, BADU OmniTronic oder über ein kleines
Koppelrelais geschehen. Dadurch wird die Elektronik weniger belastet.
Übersicht möglicher Betriebs- und Fehlermeldungen
Ist ein Fehler aufgetreten, schaltet der Motor dauerhaft ab und es wird
eine Fehlermeldung angezeigt. Ausnahme: "Unterspannung" beim Ausfall
oder Abschalten der Netzversorgung. Bei diesem Fehler startet der
Antrieb beim nächsten Zuschalten der Netzspannung neu.
Tritt ein Defekt auf, so ist die Anlage von der Spannungsversorgung zu
trennen. Siehe Kapitel 2.2 der Originalbetriebsanleitung "Normal und
selbstansaugende Pumpe mit/ohne Kunststofflaternen-Ausführung (-AK)".
Fehler-Nr.
Beschreibung
Err 1
Unterspannung Zwischenkreis
Err 2
Überspannung Zwischenkreis
Err 3
Netzspannung zu niedrig / zu hoch
Err 4
Temperatur an Leistungselektronik zu hoch
Err 5
Übertemperatur Motor
Err 7
Überstrom Elektronik
Err 10
Strommessung fehlerhaft
Err 20
Abbruch beim Anlauf, Überlastung
Err 64
Kurzschluss Elektronik
Err 97
Gleichzeitiges Auftreten mehrerer Fehler
Err 98
Verbindung zum Bedienteil fehlerhaft
10|2021 EN 13
EN Pump data sheet
Related Documentation
The additional information compiled in this data sheet must be
kept together with the original operation manual for "Non-self-
priming and self-priming pumps with/without plastic lanterns"
and must be accessible to the relevant personnel at all times.
Variostar
VW21.08.700-P
EN 14 10|2021
Glossary
TD
Technical data
Sa
Inlet connection
Da
Outlet connection
d-Saug
Recommended diameter for the suction line from 5 m
d-Druck
Recommended diameter for the pressure line from 5 m
max. L
Maximum length of the pump
D
Density
P1
Power input
P2
Power output
I
Rated current
Lpa (1 m)
Sound pressure level at 1 m measured in accordance with DIN 45635
Lwa
Acoustic capacity
m
Weight
WSK
Built-in or external overload switch
PTC
PTC resistor
Hmax.
Total dynamic head
SP
Self-priming
Hs; Hz
Geodetic head between water level and pump
Hs
Total suction head
Hz
Total dynamic head with flooded suction
IP
Type of motor enclosure
W-Kl
Class of insulation
n
Motor speed
P-GHI
2.5 bar max. casing pressure/system pressure
T
Water temperature
Yes
No
T/°C
Clarification of the max. water temperature 40 °C (60 °C): 40 °C = the
max. water temperature allowed according to the GS approval.
(60 °C) = the pump is designed to withstand a max. water
temperature of 60 °C.
1~/3~
Suitable for continuous operation at
1~ 220 - 240 V ± 5%
3~ Y/∆ 380 - 420 V/220 - 240 V ± 5%
3~ Y/∆ 660 - 725 V/380 - 420 V ± 5%
For standard voltage in accordance with DIN IEC 60038;
DIN EN 60034
10|2021 EN 15
The pump has a permanent magnetic motor and is electronically
protected against overload.
Connecting external switch contacts
The pump has an 8-wire cable with open ends for external control.
Assignment of the cables to the individual speeds is as follows:
The cables must be connected potential free. Only switch the
contacts individually (observe priority of the contacts). Otherwise
the desired speed is not activated.
WG27.50.135-2-P
Blue
Green
Yellow
Red
Black
Orange
Violet
Brown
= GND analog
= n 1
= n 2
= n 3
= Stopp
= GND digital
= Analog 0 - 10 V
= Analog 4 - 20 mA
Priority
Low
n1
High
Stop
WG27.50.094-2-P
n2 n3
EN 16 10|2021
NOTICE
The motor speed is switched on using the manual button or external
switch contacts.
The switch contacts and the assigned speed are
activated.
During operation the pump is started up to the fixed speed directly,
without
ventilation time.
If external control is not necessary, the cable ends need to be insulated.
NOTICE
For easy interaction with peripheral devices such as electric heat
exchangers or dosing systems,
installing a flow monitor with the
appropriate evaluation unit is recommended
. This can also output a fault
message.
0 1 23 4 5 6 78 9 10 11 12 1413 15 16 17 18 19 20 21
200
400
600
800
1000
1200
1400
1600
1800
2000
n [min
-1
]
l [mA]
0 1 23 4 5 6 7 8 9 10 11
U [V]
200
400
600
800
1000
1200
1400
1600
1800
2000
n [min
-1
]
10|2021 EN 17
NOTICE
The following points must be observed
in order to avoid motor
malfunctions:
The control line should be correctly installed by a specialist.
Assembly parallel to power lines or their load should be avoided.
Should the control lines be extended, dangerous voltages can occur
at the digital input. These should be avoided with isolation.
The power cables for various inputs should not be connected to the
same supply line.
Default setting:
Speed:
Ventilation speed:
Ventilation time:
Speed which can be set:
Ventilation time which can be set:
External controlling:
Switching behaviour input "0":
1 = 600 rpm
2 = 1100 rpm
3 = 1800 rpm
= 1800 rpm
= oFF
600 1800 rpm (in 10 rpm steps)
oFF, 1 10 min. (in 1 min. steps)
oFF
0 cl
User interface:
(1) LED display: displays the current speed
of the motor.
(2) : selection of the preset speeds.
(3) : to display the current consumption
and select the parameters in the setup.
(4) : to set the parameters.
(5) : to change the speed
.
(6) : to stop the motor.
The software version "-rX.X-" is displayed briefly when the supply
voltage is switched on.
WG27.50.136-P
4
6
5
1
2
3
EN 18 10|2021
Operation:
Press the button or to select the preset fixed
speed.
The pump is programmed according to the factory
settings, without ventilation time
If the venting phase of the pump is activated, a bar
runs from the lower, through the middle to the upper
position in the first section in the display.
During operation the pump is started up to the fixed
speed directly, without ventilation phase.
The motor is stopped by pressing the button. The
"Power" LED flashes and the display shows "oFF".
If an analogue control is set in the parameters, the
motor can be restarted with the button.
Setting the speeds:
Press the button of the fixed speed that is to be
changed ( or ) and then change the speed by
using the buttons. The set speed is stored
directly and approached immediately when the fixed
speed is selected again.
Notice: The speed cannot be changed during the ventilation
phase.
Setting the parameters:
You can change to the setup menu by pressing the
button for 3 seconds. There the button can be used
to scroll through the menu.
The first position of the display shows the current
menu item and the remaining four positions show the
parameter to be set.
If the button is pressed within the menu, all the
changed values are stored and the setup menu exited.
The text "StorE" is shown in the display.
If you press the button, the setup menu is exited
without the changed values being stored.
Priming parameters:
The speed is set under the menu item "n" while the
time during the ventilation phase is set under the item
"t".
"t oFF" = no ventilation phase
from oFF, 1 - 10 minutes can be set
WG27.50.137-P
WG27.50.138-P
WG27.50.009-P
10|2021 EN 19
Digital Inputs/analogue inputs:
External controlling can be activated or deactivated
with the menu item "E".
"oFF" = deactivated
"dl" = digital inputs (potential-free) activated
"Uin" = analogue input (potential-free) 0-10 V
"lin" = analogue input (potential-free) 4-20 mA
Switching behaviour "0" (stop):
The switching behaviour of the digital input "0" (stop)
can be changed by using the menu item "0".
"cL" means that the motor is stopped at a closed stop
contact.
"oP" means that the motor is stopped at an open stop
contact.
"not" means that the external contact for stopping is
not required. Opening the GND contact stops the
motor.
Resetting:
The motor is reset to the factory setting when the
button is pressed for at least 10 seconds. The motor
stops and "rESEt" is displayed.
The pump’s current power requirements are shown in
watt (P XXX) in the display when the button is
pressed.
The control unit's display switches off after three
minutes without action.
After a voltage drop the pump automatically starts up again with the
speed last set, or remains stopped if it had been stopped beforehand.
WG27.50.011-P
WG27.50.012-P
WG27.50.013-P
WG27.50.014-P
EN 20 10|2021
The pump can be turned on and off using the control cable (potential-free
contact) intended for this purpose. This can be via a BADU Logic control,
BADU OmniTronic or via a small coupling relay. This puts less stress on
the electronics.
Overview of possible operating and error messages
If an error occurs, the motor switches off permanently and a message is
displayed. Exception: "Under voltage" if there is a failure or the power
supply switches off. In this case the motor restarts when the power supply
is switched on again.
If a defect occurs, the system must be disconnected from the power
supply. See chapter 2.2 of the original operating manual "Non self-priming
and self-priming pumps with/without plastic lanterns (AK version)".
Error No.
Description
Err 1
Undervoltage intermediate circuit
Err 2
Overvoltage intermediate circuit
Err 3
Supply voltage too low/too high
Err 4
Temperature at the power electronics too high
Err 5
Overtemperature motor
Err 7
Overcurrent electronics
Err 10
Current measurement faulty
Err 20
Abortion during start-up, overload
Err 64
Short-circuit electronics
Err 97
Simultaneous occurrence of several errors or faults
Err 98
Connection to the control unit faulty
/