Bosch NGM3050UC Guide d'installation

Taper
Guide d'installation

Ce manuel convient également à

Register your
appliance and join
the Bosch
family of perks:
bosch-home.com/us/
mybosch
Gas cooktop
NGM3051UC NGM3050UC
[en-us] Installation Instructions Gas cooktop 2
[fr-ca] Instructions d’installation Surface de cuisson au gaz 17
[es-mx] Instrucciones de instalación Placa a gas 34
2
Table of contents
1 IMPORTANT SAFETY INSTRUCTIONS.................... 3
1.1 Safety definitions....................................................... 4
1.2 General information................................................... 4
1.3 General safety instructions........................................ 4
1.4 Appliance handling safety ......................................... 4
1.5 Safety codes and standards...................................... 5
1.6 Electrical safety......................................................... 5
1.7 Gas safety................................................................. 5
1.8 Propane gas installation............................................ 6
1.9 Ventilation recommendations.................................... 6
1.10 High altitude installation .......................................... 6
1.11 State of California Proposition 65 Warnings ............ 6
2 Before you begin....................................................... 7
2.1 Parts included ........................................................... 7
2.2 Tools and parts needed ............................................ 7
2.3 General requirements ............................................... 7
2.4 Cabinet requirements................................................ 7
2.5 Countertop requirements .......................................... 7
2.6 Gas requirements ..................................................... 8
2.7 Electrical requirements.............................................. 8
3 Prepare installation space........................................ 8
3.1 Installation dimensions.............................................. 8
4 Installation procedure .............................................. 9
4.1 Preparing the cooktop............................................... 9
4.2 Installing the pressure regulator ................................ 9
4.3 Securing the cooktop in the countertop ................... 10
4.4 Connection overview............................................... 11
4.5 Connecting the gas supply line ............................... 11
4.6 Connecting the electrical supply.............................. 12
4.7 Assembling the burner parts ................................... 12
4.8 Installing the burner grates...................................... 12
4.9 Checking the installation ......................................... 13
5 Conversion to LP gas ............................................. 14
5.1 Converting the pressure regulator ........................... 14
5.2 Replacing the orifices.............................................. 15
5.3 Adjusting the gas valves ......................................... 15
5.4 Burner chart ............................................................ 16
6 Customer Service ................................................... 16
6.1 Model number (E-Nr.) and production number
(FD) ........................................................................ 16
6.2 Rating plate location................................................ 16
en-us
3
Read all instructions carefully before use. These precautions will reduce the risk of electrical shock, fire and injury to
persons. When using kitchen appliances, basic safety precautions must be followed including those in the following
pages.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
en-us
4
1.1 Safety definitions
Here you can find explanations of the safety signal words
used in this manual.
WARNING
This indicates that death or serious injuries may occur as
a result of non-observance of this warning.
CAUTION
This indicates that minor or moderate injuries may occur
as a result of non-observance of this warning.
NOTICE:
This indicates that damage to the appliance or property
may occur as a result of non-compliance with this
advisory.
Note:This alerts you to important information and/or tips.
1.2 General information
¡Read this manual carefully.
¡Keep the manual and the product information in a safe
place for future reference or for the next owner.
¡Do not connect the appliance if it has been damaged in
transit.
1.3 General safety instructions
IMPORTANT: THE APPLIANCE MUST BE INSTALLED
BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE THESE INSTRUCTIONS FOR THE
LOCAL ELECTRICAL INSPECTOR’S USE.
OWNER: PLEASE RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
INSTALLER: LEAVE THESE INSTRUCTIONS WITH
THE APPLIANCE AFTER INSTALLATION IS
COMPLETE.
Examine the appliance after unpacking it. In the event of
transport damage, do not plug it in.
WARNING
If the information in this manual is not followed exactly, fire
or shock may result causing property damage or personal
injury.
Do not repair, replace or remove any part of the appliance
unless specifically recommended in the manuals.
Improper installation, service or maintenance can cause
injury or property damage.
Refer to this manual for guidance.
All other servicing should be done by an authorized
service provider.
Disconnect electrical and gas supply before servicing.
When installing a cooktop over a single oven, be sure to
follow the instructions in both the oven's and the cooktop's
installation manuals.
You can find a list of approved combinations of cooktop
and oven in the Approved Combination Matrix of your
cooktop, or you can contact Customer Service for the
latest list of approved combinations. Do not try to install
your cooktop over any oven that is not stated in that list.
Never modify or alter the construction of the appliance.
The appliance should only be used if installed by a
qualified technician in accordance with these installation
instructions. The manufacturer is not responsible for any
damage resulting from incorrect installation.
To eliminate the risk of burns or fire by reaching over
heated surface units, cabinet storage space located above
the surface units should be avoided.
If cabinet storage is to be provided, the risk can be
reduced by installing a hood that projects horizontally a
minimum of 5" (127mm) beyond the bottom of the
cabinet.
Verify that cabinets above the cooktop are a maximum
of 13" (330mm) deep.
WARNING
The bottom of the cooktop can become hot.
If the cooktop is not installed in combination with an
oven, install a horizontal panel below the cooktop to
prevent accidental contact. Refer to the section on
installing a horizontal panel. →
Page9
WARNING
Remove all tape and packaging before using the
appliance.
Destroy the packaging after unpacking the appliance.
Dispose of packaging in an environmentally responsible
manner.
Never allow children to play with packaging material.
Store small parts safely as they can be a choke hazard.
1.4 Appliance handling safety
WARNING
Hidden surfaces may have sharp edges.
Use caution when reaching behind or under appliance.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
en-us
5
1.5 Safety codes and standards
This appliance complies with the latest version of one or
more of the following standards:
¡ANSI Z21.1 / CSA 1.1 Household Cooking Gas
Appliances
¡Installation must conform with local codes or, in the
absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1/NFPA 54 or, in Canada, the
Natural Gas and Propane Installation Code, CSA
B149.1.
It is the responsibility of the owner and the installer to
determine if additional requirements and/or standards
apply to specific installations.
1.6 Electrical safety
¡Installer - show the owner the location of the circuit
breaker or fuse. Mark it for easy reference.
¡If required by the National Electrical Code (or Canadian
Electrical Code), this appliance must be installed on a
separate branch circuit.
¡Local codes vary. The installer is responsible for
ensuring that the installation, connections, and
grounding comply with all applicable codes. The
manufacturer is not responsible for any issues
associated with the improper installation of this product.
¡The appliance must be electrically grounded in
accordance with local codes or, in the absence of local
codes, with the National Electrical Code, NFPA 70
latest edition or, in Canada, the Canadian Electric
Code, CSA C22.1-02.
¡Be sure your appliance is properly installed and
grounded by a qualified technician. Installation,
electrical connections and grounding must comply with
all applicable codes.
¡Do not use an extension cord.
¡Do not use an adapter.
¡Refer to the rating plate for more information.
→
"Rating plate location", Page16
WARNING
Before installing, turn power OFF at the service panel.
Lock service panel to prevent power from being turned
ON accidentally.
For appliances equipped with a cord and plug, do not cut
or remove the ground prong.
It must be plugged into a matching grounding type
receptacle to avoid electrical shock.
If there is any doubt as to whether the wall receptacle is
properly grounded, the customer should have it
checked by a qualified electrician.
GROUNDING INSTRUCTIONS
This appliance must be grounded.
Grounding reduces the risk of electric shock by
providing a safe pathway for electric current in the
event of a short circuit.
Be sure your appliance is properly installed and
grounded by a qualified technician.
Installation, electrical connections and grounding must
comply with all applicable codes.
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician install an outlet near
the appliance.
Before you plug in an electrical cord, be sure all controls
are in the OFF position.
Before you turn on power supply, make sure all controls
are in the OFF position.
1.7 Gas safety
Requirements for gas supply:
¡Install a gas shutoff valve near the appliance. It must be
easily accessible in an emergency.
¡Leak testing must be conducted by the installer
according to the instructions in this manual.
¡The appliance and its individual shutoff valve must be
disconnected from the gas supply piping system during
any pressure testing at pressures in excess of ½psi
(3.5kPa).
¡The appliance must be isolated from the gas supply
piping system by closing its individual manual shutoff
valve during any pressure testing of the gas supply
piping system at test pressures equal to or less than
½psi (3.5kPa).
¡The minimum supply pressure must be 1" water column
above the manifold pressure printed on the rating label.
The maximum supply pressure must not exceed 14.0
inches water column (34.9Millibars).
¡A metal flex line or fixed metal pipe shall be used to
connect gas to the appliance. If a metal gas line cannot
be used, consult your local certified electrician or local
electric codes for proper grounding.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
en-us
6
IMPORTANT SAFETY NOTICE: Burning gas cooking fuel
generates some by-products which are on the list of
substances which are known by the State of California to
cause cancer or reproductive harm. To minimize exposure
to these substances, always operate this unit according to
the instructions contained in this booklet and provide good
ventilation.
1.8 Propane gas installation
¡The propane gas tank must be equipped with its own
high pressure regulator. In addition, the regulator
supplied with this unit must also be used.
¡The appliance is shipped from the factory for use with
natural gas. It must be converted for use with propane.
A qualified technician or certified installer must do the
conversion.
¡For use with propane the appliance must be converted
per the LP conversion instructions.
→
"Conversion to LP gas", Page14
For Massachusetts installations
¡Installation must be performed by a qualified or
licensed contractor, plumber or gas fitter qualified or
licensed by the state, province or region where this
appliance is being installed.
¡Shut-off valve must be a “T” handle gas cock.
¡Flexible gas connector must not be longer than
36inches.
Installer - show the owner where the gas shut-off valve is
located.
1.9 Ventilation recommendations
We strongly recommend the installation of a ventilation
hood above this appliance.
The hood must be installed according to instructions
furnished with the hood.
WARNING
The appliance should not be installed with a ventilation
system that blows air downward toward the burners. This
type of ventilation system may cause ignition and
combustion problems with the gas cooking appliance
resulting in personal injury or unintended operation.
1.10 High altitude installation
This appliance has been tested for operation up to an
altitude of 10,100ft (3,080m) elevation above sea level.
For altitudes above 2,000ft (610m) elevation above sea
level, burner flame adjustments may be necessary.
Burners should be checked at the lowest setting, if the
flame is not stable the simmer should be increased until
the flame is stable. This can be done by adjusting the
bypass screw in the valve. If flame performance is
satisfactory, adjustment will not be required. It is required
that a certified professional make the high altitude
adjustments during installation.
1.11 State of California Proposition 65
Warnings
This product may contain a chemical known to the State
of California, which can cause cancer or reproductive
harm. Therefore, the packaging of your product may bear
the following label as required by California:
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
Before you begin en-us
7
Before you begin
2 Before you begin
Before you begin
Read these instructions before you begin to install your
appliance.
2.1 Parts included
After unpacking all the parts, check for any damage in
transit and for completeness of delivery.
¡Cooktop
¡Hold-down brackets (4)
¡Sheet metal screws, 8-18 (25.4mm), (4)
¡Burner grates (3)
¡Burners (NGM3051UC: 4 / NGM3050UC: 5)
¡Burner caps (NGM3051UC: 4 / NGM3050UC: 5)
¡Pressure regulator
¡LP gas conversion kit
2.2 Tools and parts needed
Prepare these tools and accessories before you start to
install your appliance.
¡Pencil
¡Measuring tape
¡Cross head screwdriver
¡Drill with bit 1/4" (6mm)
¡Jigsaw
¡Adjustable wrench
¡Teflon® tape - gas rated
¡Flathead screwdriver, 1/8"
Additional tools needed for LP gas conversion
¡7mm socket wrench
¡Flat blade screwdriver with small thin blade
¡T10 star bit screwdriver
¡T20 star bit screwdriver
¡Small piece of tape
Notes
¡For stand-alone installation a horizontal panel below the
cooktop may be needed.
→
"Installation with horizontal panel", Page9
¡Additional materials may be necessary for installation in
solid surface countertops. Contact the countertop
manufacturer.
2.3 General requirements
Ensure that the following requirements are met when
planning the installation of your appliance.
¡Plan the installation of the unit so that the power cord,
gas shut-off valve and gas pressure regulator are
accessible from the front of the cabinet.
¡Make sure the gas supply line does not interfere with
the back of the appliance.
¡The cabinet in which the cooktop is installed must be
properly secured, level and stable.
¡Any laminated coverings and glue on cabinets next to
the cooktop must be made of non-flammable and heat
resistant materials. Refer to local building codes for
acceptable materials.
¡This appliance cannot be installed above refrigerators,
washing machines, dishwashers or similar.
¡If the cooktop will be installed in combination with an
oven, refer to the Approved Combination Matrix
included with the product for cutout and clearance
dimensions.
2.4 Cabinet requirements
Ensure that the cabinetry at the installation location meets
the requirements for a safe installation.
The minimum spaces that must be maintained when
installing the gas cooktop shall be the following:
a min. 13" (330mm)
for installation next to oven min. 13" (330mm)
b min. 13" (330mm)
for installation next to oven min. 13" (330mm)
c min. 30" (762mm) clearance between the top of
the cooking surface and the bottom of combustible
constructions
d min 3" (76mm);
for installation in kitchen islands, min. 4" (100mm)
e For 30" cooktops:
min. 30" (760mm) centered over cooktop
f min. 18" (458mm)
g max. 13" (330mm)
h min. 1¾" (48mm);
for installation in kitchen islands, min. 4" (100mm)
2.5 Countertop requirements
Ensure that the countertop into which the cooktop is to be
installed meets these requirements for a safe installation.
WARNING
To reduce the risk of ignition of surrounding combustible
materials, install at least 13" (330mm) from both sidewalls
and at least 3" (76mm) from the rear wall.
en-us Prepare installation space
8
¡The countertop must be level.
¡The stability of the countertop must be maintained after
the cut-out has been made.
¡Solid surface or laminate countertops often require
special installations. For example, heat-reflective tape
and rounded corners may be necessary. Contact the
countertop manufacturer for instructions specific to your
countertop.
2.6 Gas requirements
Ensure that the requirements for the gas supply are met.
The cooktop is shipped from the factory for use with
natural gas. For use with LP conversion, a certified
technician or installer must do the conversion.
Supply pressure:
¡Natural Gas: 7 inches water column (17.4 Millibars)
¡Propane Gas: 11 inches water column (27.4 Millibars)
¡The propane gas tank must be equipped with its own
high pressure regulator in addition to the pressure
regulator supplied with this unit.
2.7 Electrical requirements
Ensure that the following electrical requirements are met.
CAUTION
Do not use an extension cord with this appliance.
¡This appliance requires a 60Hz, 15Amp, 120VAC
connection.
¡The appliance is equipped with a 40" (1000mm) power
cord.
¡The power connection must remain accessible from the
front of the cabinet after the installation is complete.
Prepare installation space
3 Prepare installation space
Prepare installation space
Create the cutout in the countertop according to the
instructions.
General countertop requirements:
¡The angle of the cut surface to the countertop surface
must be 90°.
¡With multi-layered countertops, secure strips laterally in
the cutout if necessary.
¡After creating the cutout, remove all debris.
¡If the cooktop will be installed in combination with an
oven, refer to the Approved Combination Matrix
included with the product for cutout and clearance
dimensions.
¡Observe the minimum distance between device
underside and cabinet surfaces of ⅜" (10mm).
WARNING
The bottom of the cooktop can become hot.
If the cooktop is not installed in combination with an
oven, install a horizontal panel below the cooktop to
prevent accidental contact. Refer to the section on
installing a horizontal panel. →
Page9
3.1 Installation dimensions
*For installation in a kitchen island.
Installation over oven
A min. ¾" (19 mm)
max. 2" (50 mm)
B 5⅞" (150 mm)
C 2¾" (70 mm)
D Refer to Approved Combination Matrix
Installation procedure en-us
9
E 1¾" (45mm)
Installation with horizontal panel
If there is no oven beneath the cooktop, install a horizontal
panel. To allow access to the power supply connection
and regulator maintain a minimum clearance of ⅜"
(10mm) from the edges of the panel(F).
IMPORTANT: Complete the installation of the cooktop
before installing the horizontal panel.
Installation above a drawer
A min. ¾" (19 mm)
max. 2" (50 mm)
B 5⅞" (150 mm)
C 2¾" (70 mm)
D min. 0" (0 mm)
E 1¾" (45mm)
F min. ⅜" (10 mm)
Installation above a cabinet door
A min. ¾" (19 mm)
max. 2" (50 mm)
B 5⅞" (150 mm)
C 2¾" (70 mm)
D min. 0" (0 mm)
E 1¾" (45mm)
F min. ⅜" (10 mm)
G min. 1" (25)
Installation procedure
4 Installation procedure
Installation procedure
Follow these instructions to install the cooktop into the
countertop.
CAUTION
Sharp edges.
Use protective gloves when installing the appliance.
CAUTION
The appliance is heavy.
It is recommended that two people install this appliance.
4.1 Preparing the cooktop
Requirement:IMPORTANT: A foam tape seal is factory
installed on the underside of the cooktop to prevent leaks.
Do not remove the seal under any circumstances.
1. Place the cooktop face down on a soft and stable
surface. Use the foam sheet from the packaging to
protect surfaces from scratching.
2. Attach the hold-down brackets to the underside of the
cooktop with the provided short screws. Loosely tighten
the screws so the clamps do not move freely. Rotate
the hold-down brackets so that the appliance can be
placed in the cutout.
Note:The rating plate will not be accessible after
installation. Make a note of your appliance's details or
refer to the enclosed appliance certificate.
4.2 Installing the pressure regulator
WARNING
Do not attempt any adjustment of the pressure regulator,
except when converting to propane. Adjustments could
lead to leaks or cause incorrect gas pressure to the
appliance.
en-us Installation procedure
10
Make sure the used gas connection line is not connected
to the gas supply, before carrying out the following steps.
Note:All pipe connections must be sealed in accordance
with local codes.
1. Identify the parts of the pressure regulator.
a Appliance manifold connection
b Conversion cap
c Pressure regulator
d Arrow on pressure regulator, shows the
direction of gas flow
2. Apply Teflon® tape on the threads of the manifold pipe.
Install the pressure regulator (supplied with cooktop) to
the gas inlet with the gas flow arrow facing the manifold
inlet.
3. Firmly hand tighten the regulator, then further tighten ¼
turn to a maximum of one complete turn. Align the
regulator so that the conversion cap is easily
accessible.
4. WARNING Never reuse a gas connector.
Repeated bending, flexing, or extreme vibration will
cause metal fatigue and must be avoided.
Apply Teflon® tape to the male threads, then connect a
new ½" metal flex line or fixed metal pipe connection to
the pressure regulator.
Note:For installations with little space, use a 90° street
elbow (not supplied) to orient the regulator horizontally.
4.3 Securing the cooktop in the countertop
The cooktop must be secured from below using the hold-
down brackets provided.
WARNING
Before installing, turn power OFF at the service panel.
Lock service panel to prevent power from being turned
ON accidentally.
Requirement:IMPORTANT: A foam tape seal is factory
installed on the underside of the cooktop to prevent leaks.
Do not remove the seal under any circumstances.
1. CAUTION Do not let the cooktop drop into place.
Make sure that the cooktop is supported along the
edges when carefully placing it into the cutout.
Turn the cooktop over carefully making sure not to
damage the pressure regulator and gas line.
Place the cooktop carefully into the countertop
cutout, pulling it towards the front of the cutout ⁠.
Lower the rear of the cooktop so that is rests flat on
the counter ⁠.
Center the cooktop left and right in the cutout ⁠.
3
2. Rotate the hold-down brackets so that they will contact
the underside of the countertop.
Hand-tighten one hold-down bracket and check the
cooktop position, then secure the cooktop by
tightening all the brackets. Do not over-tighten.
The orientation of the hold-down brackets depends
on the thickness of the countertop.
Installation procedure en-us
11
(19)
¾"
a Cooktop
b Countertop
Note:Do not use silicone to glue the cooktop to the
countertop surface.
4.4 Connection overview
Refer to this illustration for the location of the gas and
electric connection of the appliance.
Note:Your appliance is equipped for use with natural gas
on delivery. If you want to use your appliance with LP gas
refer to the section on LP gas conversion before
continuing with the installation.
a Cooktop rough-in box
b Arrow on pressure regulator, shows the direction of
gas flow
c Pressure regulator
d ½" female pipe threads
e Metal flex gas line
f Power cord (40"/1m)
g 120V receptacle
h Gas cut-off valve
i Gas supply line connection fitting
j Floor
4.5 Connecting the gas supply line
The appliance is shipped from the factory for use with
natural gas. If you want to use propane gas it must be
converted. A qualified technician or installer must do the
conversion.
Note
Ensure the following requirements are met before you try
to connect the appliance to the gas supply:
¡Before connecting the appliance, check whether the
local connection conditions such as gas type and gas
pressure match the appliance settings.
¡Make sure the gas supply is turned off at the manual
shutoff valve before connecting the appliance.
¡The gas connection must be in a location that permits
access to the manual shut-off valve and which, if
applicable, is visible after opening the door or drawers
of the cabinet.
¡The metal flex gas line must not come into contact with
moving parts of the fitted unit (e.g. drawers) or be laid in
areas where it could become trapped or damaged.
¡The metal flex gas line must not come into contact with
a cooktop, oven, dishwasher, refrigerator, washing
machine, hot water pipe, radiator or any other appliance
installed in the vicinity of the gas cooktop.
¡The metal flex gas line must not be subject to rubbing,
vibrations, kinking or any other kind of deformation. It
should be checked along its entire length with the
cooktop in the installation position.
¡All pipe connections must be sealed in accordance with
local codes.
Connect the metal flex gas line or fixed metal pipe
connection from the cooktop pressure regulator to the
manual shut-off valve.
Checking the gas line for leaks
Check the gas supply line connections for leaks using a
soap solution or non-corrosive leak detection fluid. Do not
use a flame of any sort.
Note
Important notes for gas connection:
¡The appliance and its individual shutoff valve must be
disconnected from the gas supply piping system during
any pressure testing at pressures in excess of ½psi
(3.5kPa).
¡The appliance must be isolated from the gas supply
piping system by closing its individual manual shutoff
valve during any pressure testing of the gas supply
piping system at test pressures equal to or less than
½psi (3.5kPa).
1. Turn on gas.
2. Apply a soap solution or non-corrosive leak detection
fluid to all joints and fittings in the gas connection
between the shut-off valve and the cooktop. Also check
gas fittings and joints in the cooktop if the connections
may have been disturbed during installation.
aBubbles appearing around fittings and connections
indicate a leak.
en-us Installation procedure
12
3. If a leak appears, turn off the supply line gas shut-off
valve and tighten the connections.
4. Retest for leaks by turning on the supply line gas shutoff
valve.
aWhen the leak check is complete and no bubbles
appear, the test is complete.
5. Wipe off all soap solution or detection fluid residue.
4.6 Connecting the electrical supply
CAUTION
Before you plug in the electrical cord, make sure that the
gas shut-off valve and all burner controls are in the OFF
position.
Connect the plug of the electrical cord to a grounded
power outlet. The outlet must be accessible after the
installation of the appliance is complete.
4.7 Assembling the burner parts
The burner parts must be properly placed for the cooktop
to function properly.
Note
If the burner parts are not properly placed, one or more of
the following problems may occur:
¡The burner flames are too high.
¡Flames shoot out of the burners.
¡The burners do not ignite.
¡The burner flames light unevenly.
¡The burners emit gas odor.
WARNING
Remove all tape from the burner parts and the cooktop
surface before using the appliance.
1. Assemble the burner parts according to the illustration.
1
2
3
4
1
Burner cap
2
Burner base
3
Thermocouple
4
Igniter
Make sure that the prongs of the burner cap fit snugly
into the groove of the burner base.
2. Check to make sure that there is no gap between the
burner parts. You may gently try to move the burner
parts from side to side to check if they are properly
seated.
4.8 Installing the burner grates
WARNING
Improperly positioned grates can cause flare-ups.
Position all grates properly on the cooktop whenever
the cooktop is in use to properly support pots and avoid
spills.
Make sure each of the four feet of the grates is placed
into the corresponding dimples on the cooktop surface.
Do not use a grate if the rubber feet are missing or
damaged.
Typical burner grate installation
Installation procedure en-us
13
NGM3051UC
NGM3050UC
4.9 Checking the installation
Check if your unit is working properly after you have
completed the installation steps.
WARNING
Before you turn on power supply, make sure all controls
are in the OFF position.
1. Ensure that the burner caps are properly positioned.
2. Turn each burner on in turn and verify that the electric
igniters are working.
Push down the control knob and turn it counter-
clockwise to the ignition symbol ⁠.
Verify that the igniter/spark module clicks.
Once the air has been purged from the supply lines,
verify that the burner lights within 4seconds.
When the burner lights, turn the control knob back to
the off position.
If any of the burners do not ignite, do not continue
testing. Call Customer Service.
3. Turn the control knob between the highest and lowest
setting. Make sure the flame does not go out and there
are no flashbacks.
4. If you have carried out an LP gas conversion, check the
lowest setting to confirm the flames are stable on the
ports and the set screws do not need to be readjusted.
5. Check the flame characteristics.
The flame should be blue with a minimal yellow tip on
the outer cone.
6. After completing all checks, complete the installation of
the horizontal panel or oven. →
Page9
Note:The appliance is shipped from the factory for use
with natural gas. If you want to use propane gas, it must
be converted. A qualified technician or installer must do
the conversion. Refer to Conversion to LP gas.
Flame characteristics
The color of the flame tells you if the gas supply is properly adjusted.
Note:Allow the appliance to operate for 4 to 5minutes before evaluating the flame. Some yellow streaking is normal
during the initial startup.
Flame Image Measure
Completely or mostly
yellow
Verify that the regulator is set for the correct fuel. Retest
after adjustment.
Yellow tips on outer
cone
Normal for LP gas
Soft blue Normal for natural gas
en-us Conversion to LP gas
14
Conversion to LP gas
5 Conversion to LP gas
Conversion to LP gas
Your appliance is equipped for use with natural gas on
delivery. It can be converted to LP gas supply.
The components required for conversion to LP gas are
contained in the LP conversion kit included with this
appliance, or are available from Customer Service.
→
"Customer Service", Page16
Only a qualified technician or installer is authorized to
convert the appliance to another gas type.
Before carrying out the conversion, turn off the electricity
and gas supply.
5.1 Converting the pressure regulator
WARNING
Turn off the electricity and gas supply before carrying out
the conversion.
1. Locate the pressure regulator on the bottom right end of
the appliance.
2. Remove the hexagon shaped conversion cap from the
regulator. Make sure not to dislodge the gasket on
the cap or the spring inside the regulator.
3. Grasp the plastic orifice stem firmly and pull it
forcefully from the conversion cap . The stem snaps
snugly into an indent in the cap and may require a
strong pull to remove. It may be helpful to gently “rock”
the plastic stem while pulling it from the metal cap.
4. Rotate the stem 180° ⁠.
aConfirm that the button end of the orifice stem is away
from the conversion cap.
aConfirm that the letters “LP” on the orifice stem are
upside down when the conversion cap is set flat on its
head.
5. Snap the orifice stem back in place in this position
inserting it into the indent in the conversion cap ⁠.
6. Insert the hexagon cap back into the regulator and
tighten, do not over-tighten.
7. IMPORTANT: Attach the metallic sticker included with
the LP conversion kit to the bottom of the appliance as
shown. This sticker provides notice that the appliance
has been converted for use with LP gas. It should be
located near the appliance rating plate.
→
"Rating plate location", Page16
Note:If you change the type of gas back to natural gas
at a later point, remove the sticker.
Conversion to LP gas en-us
15
5.2 Replacing the orifices
1. Remove all burner grates, burner caps and burner
bases.
2. Remove the natural gas orifices and replace them with
LP orifices using a 7mm socket wrench. See burner
chart.
For ease of installation use a small piece of tape and
insert it in the socket wrench to prevent the orifice
from falling out.
It is important to make sure that the orifices do not
become detached during removal or fastening. They
must be properly tightened to ensure that there are
no leaks.
Normal burner with one orifice
3. Fasten the orifices.
4. Save the orifices removed from the appliance for future
use.
5.3 Adjusting the gas valves
1. Turn the control knobs to position off.
2. Pull off the control knobs.
3. Remove the screws at each burner and lift off the main
top from the cooktop.
4. Remove the rubber gaskets from the valve stems.
5. Adjust the bypass jet on each valve with a flat blade
screwdriver, with a small thin blade. Refer to the burner
chart for the correct setting of the setting screws(M).
→
"Burner chart", Page16
Use setting for LP Gas. The bypass jet must be
tightened properly.
Use setting for natural gas. The bypass jet must be
loosened until the gas flow from the burner is correct.
Turn ¼turn to the left from LP setting.
6. Replace the rubber gaskets on the valve stems. Make
sure the D-shaped hole in the rubber gasket matches
the D-shape of the valve stem.
7. Ensure that the gaskets around the burner bases are in
place.
8. Reinstall the main top and the control knobs.
9. Replace all burner bases, burner caps and burner
grates.
10. Continue the installation procedure from
→
"Connection overview", Page11
11. When the installation is complete, verify that the
appliance works properly.
→
"Checking the installation", Page13
.
Note:In the event of damage, the valve must be
completely replaced.
en-us Customer Service
16
5.4 Burner chart
Refer to this overview for specifications of the individual burners.
Burner cap Gas type Pressure in
inch wc
Orifice BTU/h kW M (valve
adjustment
screw setting)
Small burner Natural gas
Propane gas
6
10
77
54
3,400
3,400
1.00
1.00
NGM3051UC:
Large burner
Natural gas
Propane gas
6
10
133
93
10,300
10,300
3.00
3.00
NGM3050UC:
Large burner
Natural gas
Propane gas
6
10
125
88
9,010
9,010
2.64
2.64
Medium burner Natural gas
Propane gas
6
10
102
71
6,000
6,000
1.75
1.75
Extra large
burner
Natural gas
Propane gas
6
10
168
116
16,000
16,000
4.70
4.70
Customer Service
6 Customer Service
Customer Service
With any warranty repair, we will make sure your
appliance is repaired by an authorized service provider
using genuine replacement parts. We use only genuine
replacement parts for all repairs.
Detailed information on the warranty period and terms of
warranty can be found in the Statement of Limited Product
Warranty, from your retailer, or on our website.
If you contact Customer Service, you will need the model
number (E-Nr.) and the production number (FD) of your
appliance.
USA:
1-800-944-2904
www.bosch-home.com/us/owner-support/get-support
www.bosch-home.com/us/shop
CA:
1-800-944-2904
www.bosch-home.ca/en/service/get-support
www.bosch-home.ca/en/service/cleaners-and-accessories
6.1 Model number (E-Nr.) and production
number (FD)
You can find the model number (E-Nr.) and the production
number (FD) on the appliance's rating plate.
Making a note of your appliance's details and the
Customer Service telephone number will enable you to
find them again quickly.
6.2 Rating plate location
You can find the rating plate of your appliance:
¡On the underside of the appliance.
Rating plate
fr-ca
17
Table des matières
1 IMPORTANTES CONSIGNES DE SÉCURITÉ ........ 18
1.1 Définitions des termes de sécurité .......................... 19
1.2 Indications générales .............................................. 19
1.3 Consignes générales de sécurité ............................ 19
1.4 Manipulation sécuritaire des appareils .................... 20
1.5 Codes et normes de sécurité .................................. 20
1.6 Sécurité électrique .................................................. 20
1.7 Sécurité des gaz ..................................................... 21
1.8 Installation au gaz propane ..................................... 21
1.9 Recommandations de ventilation ............................ 21
1.10 Installation à haute altitude.................................... 21
1.11 Mises en garde conformément à la proposition
65 de l'État de Californie ....................................... 22
2 Avant de commencer.............................................. 23
2.1 Pièces incluses ....................................................... 23
2.2 Outils et pièces nécessaires.................................... 23
2.3 Conditions générales .............................................. 23
2.4 Exigences concernant les armoires......................... 23
2.5 Exigences du comptoir............................................ 24
2.6 Exigences en matière de gaz .................................. 24
2.7 Exigences électriques ............................................. 24
3 Préparation préalable au montage ........................ 24
3.1 Dimensions de l’installation..................................... 24
4 Procédure d’installation ......................................... 25
4.1 Préparation de la table de cuisson .......................... 25
4.2 Installation du régulateur de pression...................... 26
4.3 Fixation de la table de cuisson dans le comptoir ..... 26
4.4 Aperçu de la connexion........................................... 27
4.5 Raccordement de la conduite d’alimentation en
gaz.......................................................................... 28
4.6 Connexion de l'alimentation électrique .................... 28
4.7 Assemblage des pièces du brûleur ......................... 28
4.8 Installation des grilles de brûleur............................. 29
4.9 Inspecter l’installation.............................................. 29
5 Conversion au gaz LP............................................. 30
5.1 Conversion du régulateur de pression..................... 30
5.2 Remplacement des orifices..................................... 31
5.3 Ajustement des soupapes de gaz ........................... 32
5.4 Tableau des brûleurs .............................................. 33
6 Service à la clientèle............................................... 33
6.1 Numéro de modèle (E-Nr.) et numéro de
fabrication (FD) ....................................................... 33
6.2 Emplacement de la plaque signalétique.................. 33
fr-ca
18
Lisez toutes les instructions attentivement avant l’utilisation. Ces précautions réduiront le risque d’électrocution, d’incendie
et de blessure pour les personnes utilisant l’appareil. Lorsque vous utilisez des appareils électroménagers, il importe de
suivre les précautions de sécurité de base, y compris celles indiquées dans les pages suivantes.
IMPORTANTES CONSIGNES DE SÉCURITÉ
LIRE ET CONSERVER CES INSTRUCTIONS
fr-ca
19
1.1 Définitions des termes de sécurité
Vous trouverez ici des explications sur les mots de
signalisation de sécurité utilisés dans ce manuel.
AVERTISSEMENT
Signale un risque de mort ou de blessure grave si
l’avertissement n’est pas respecté.
MISE EN GARDE
Signale un risque de blessures mineures ou modérées si
l’avertissement n’est pas respecté.
AVIS :
Ceci indique que la non-conformité à cet avis de sécurité
peut entraîner des dégâts matériels ou endommager
l'appareil.
Remarque:Ceci vous signale des informations et/ou
indications importantes.
1.2 Indications générales
¡Lisez attentivement cette notice.
¡Veuillez conserver la notice et les renseignements sur
le produit en vue d’une réutilisation ultérieure ou pour
un futur nouveau propriétaire.
¡Ne branchez pas l’appareil si ce dernier a été
endommagé durant le transport.
1.3 Consignes générales de sécurité
IMPORTANT: L'APPAREIL DOIT ÊTRE INSTALLÉ PAR
UN INSTALLATEUR QUALIFIÉ.
IMPORTANT: CONSERVEZ CES INSTRUCTIONS
POUR L’UTILISATION DE L’INSPECTEUR
ÉLECTRIQUE LOCAL.
PROPRIÉTAIRE: VEUILLEZ CONSERVER CES
INSTRUCTIONS POUR RÉFÉRENCE FUTURE.
INSTALLATEUR: LAISSEZ CES INSTRUCTIONS AVEC
L'APPAREIL UNE FOIS L'INSTALLATION COMPLÈTE.
Examinez l'appareil après l'avoir déballé. En cas de
dommage en cours de transport, ne branchez pas
l'appareil.
AVERTISSEMENT
Si les consignes du présent manuel ne sont pas suivies à
la lettre, il y a un risque d’incendie ou d’électrocution
pouvant entraîner des dommages matériels ou des
blessures.
Ne pas réparer, remplacer ni retirer toute pièce de
l’électroménager à moins que cela ne soit spécifiquement
recommandé par les manuels. L’installation, les
réparations ou l’entretien inadéquats pourraient causer
des blessures ou des dégâts matériels.
Consulter ce manuel pour les directives d’utilisation.
Toutes les autres réparations doivent être effectuées
par un prestataire de services agréé.
Couper l’alimentation électrique et de gaz avant toute
réparation.
Lorsque vous installez une table de cuisson sur un seul
four, veillez à suivre les instructions des manuels
d'installation du four et de la table de cuisson.
Vous pouvez trouver une liste des combinaisons
approuvées de table de cuisson et de four dans la
matrice de combinaisons approuvées de votre table de
cuisson, ou vous pouvez contacter le service clientèle
pour obtenir la dernière liste des combinaisons
approuvées. Ne pas essayer d'installer la table de
cuisson au-dessus de n'importe quel four non énuméré
dans cette liste.
Ne jamais modifier ni altérer la structure de l’appareil
électroménager.
Utilisez uniquement l’appareil électroménager s’il a été
installé par un technicien qualifié conformément aux
présentes instructions d’installation. Le fabricant ne peut
pas être tenu responsable de tous dommages causés par
une installation inadéquate.
Pour éliminer le risque de brûlure ou d'incendie lorsque
vous vous étirez au-dessus des surfaces chauffantes de
l'électroménager, il faut éviter d'installer des armoires de
rangement au-dessus de la surface de l'électroménager.
Si une armoire de rangement est installé, il est possible
de réduire le risque en installant une hotte qui dépasse
(horizontalement) d'au moins 5po (127mm) le bord du
fond de l'armoire.
Vérifier que la profondeur des armoires au-dessus de la
table de cuisson est au maximum de 13po (330mm).
AVERTISSEMENT
Le dessous de la table de cuisson peut devenir chaud.
Si la table de cuisson n'est pas installée en
combinaison avec un four, installez un panneau
horizontal sous la table de cuisson pour éviter tout
contact accidentel. Reportez-vous à la section sur
l'installation d'un panneau horizontal. →
Page25
IMPORTANTES CONSIGNES DE SÉCURITÉ
LIRE ET CONSERVER CES INSTRUCTIONS
fr-ca
20
AVERTISSEMENT
Retirer tout le ruban adhésif et l'emballage avant d'utiliser
l'électroménager.
Jetez l'emballage après avoir déballé l'électroménager.
Éliminez l'emballage d'une manière respectueuse de
l'environnement.
Ne laissez jamais les enfants jouer avec le matériel
d’emballage.
Conservez les pièces de petite taille dans un endroit
sûr, car elles peuvent être avalées facilement.
1.4 Manipulation sécuritaire des
appareils
AVERTISSEMENT
Certaines surfaces cachées peuvent avoir des
rebords tranchants.
Redoubler de vigilance quand vous passez la main
derrière ou sous l'appareil électroménager.
1.5 Codes et normes de sécurité
Cet appareil est conforme aux plus récentes versions de
l'une ou plus des normes suivantes:
¡ANSIZ21.1/CSA1.1, Appareils électroménagers pour
la cuisson à gaz
¡L’installation doit être conforme aux codes locaux ou,
en l’absence de tels codes, au National Fuel Gas Code
ANSIZ223.1/NFPA54 ou, au Canada, au code
national CSAB149.1 d’installation du gaz naturel et du
propane.
Il est de la responsabilité du propriétaire et de l'installateur
de déterminer si des exigences et/ou des normes
supplémentaires s'appliquent à des installations
spécifiques.
1.6 Sécurité électrique
¡Installateur - indiquez au propriétaire l’emplacement
du disjoncteur ou du fusible. Identifiez sa position pour
pouvoir le retrouver facilement.
¡S’il y a lieu, conformément au Code national de
l’électricit (ou au Code canadien de l’électricité), cet
appareil doit être installé sur un circuit de dérivation
séparé.
¡Les codes locaux peuvent varier. L'installateur est
responsable de s'assurer que l'installation, les
connexions et la mise à la terre sont conformes à tous
les codes applicables. Le fabricant n'est pas
responsable des problèmes associés à une mauvaise
installation de ce produit.
¡L’appareil doit être mise à la terre en conformité aux
codes locaux, ou en l’absence de tels codes, à la
dernière version du National Electric CodeNFPA70
ou, au Canada, au code canadien de
l’électricitéCSAC22.1-02.
¡Assurez-vous que l’appareil est correctement installé et
mis à la terre par un technicien qualifié. L’installation,
les raccordements électriques et la mise à la terre
doivent être conformes avec tous les codes en vigueur.
¡N'utilisez pas de rallonge.
¡N'utilise pas un adaptateur.
¡Voir la fiche signalétique pour plus d'information.
→
"Emplacement de la plaque signalétique", Page33
AVERTISSEMENT
Avant l'installation, couper l'alimentation au panneau de
service.
Verrouiller le panneau de service pour empêcher que
l'alimentation ne soit rétablie par accident.
Pour les électroménagers dotés d'un cordon
d'alimentation avec fiche, ne pas couper ni enlever la
broche de mise à la terre.
Pour éviter toute électrocution, brancher le cordon dans
une prise de courant correspondante avec mise à la
terre.
En cas de doute concernant la mise à la terre
appropriée de la prise murale, le client doit faire vérifier
celle-ci par un électricien qualifié.
INSTRUCTIONS DE MISE À LA TERRE
Cet appareil doit être mis à la terre.
La mise à la terre réduit le risque de choc électrique en
fournissant une voie sûre pour le courant électrique en
cas de court-circuit.
Assurez-vous que l’appareil est correctement installé et
mis à la terre par un technicien qualifié.
L’installation, les raccordements électriques et la mise
à la terre doivent être conformes avec tous les codes
en vigueur.
N'utilisez pas de rallonge. Si lecordon d'alimentation est
trop court, demandez à unélectricienouun technicien
qualifié d'installerune prise à proximité de l'appareil.
IMPORTANTES CONSIGNES DE SÉCURITÉ
LIRE ET CONSERVER CES INSTRUCTIONS
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Bosch NGM3050UC Guide d'installation

Taper
Guide d'installation
Ce manuel convient également à