SW-Motech KFT.22.995.72000/S Mounting instructions

ANBAUANLEITUNG

mounting instructions • instructions de montage • instrucciones de montaje • istruzioni di montaggio

beinhaltet • contains • contient • contiene • contiene

KFT.22.995.72000/S

AKR.00.011.10000/S

KFT.22.995.30001/B

KFT.00.152.35100

ALK.00.733.10000L/S

ALK.00.733.11000R/S

QLS.00.095.15100

www.akrapovic.com

Installation instructions

Akrapovič Product:

for the

Slip-On

Ducati DesertX

Revision 1.0

EN

02/2023

D250.1.00.0000 C

*508911*

www.akrapovic.com

2 / 14

Congratulations on purchasing the Akrapovič product. The Akrapovič product is made by Akrapovič d.d., Malo

Hudo 8a, 1295 Ivančna Gorica, Slovenia (“Akrapovič”).

Akrapovič product should only be installed by persons skilled in motorcycle exhaust system or other motorcycle

parts installation and performance. The instructions provided in this manual should be followed to ensure

proper installation and safe use of the Akrapovič product. Akrapovič and/or its partners shall not be held liable

for any damage or personal injury (including direct, indirect, or consequential damage) sustained as a result

of improper installation of the Akrapovič product or its use and maintenance contrary to the instructions and

warnings contained herein.

If you have any questions regarding the installation and/or proper use of the Akrapovič product or this manual,

please contact your local Akrapovič partner.

For more information on the Akrapovič product, see the ocial Akrapovič website at:

http://www.akrapovic.com

Your safety is our number one priority. Please ride your motorcycle responsibly, safely and always obey local

trac rules.

All statements made with regard to the product’s compliance are made in respect of the product “as is”. Any

modications of the Akrapovič product or its improper installation, use or maintenance that is not in accordance

with this Installation manual, may result in severe damage to the product and/or motorcycle, as well as personal

injury, and may aect the product’s compliance with the legal requirements, such as product’s air and/or noise

emissions (as an example, the motorcycle may not be suitable for use on public roads any longer), as well as

warranty coverage.

The product may only be used in accordance with relevant laws and regulations, including state and federal,

where applicable.

Damage caused by improper installation, use and maintenance of the Akrapovič product is not covered by the

Akrapovič warranty. Please refer to the enclosed warranty with regard to the terms of our warranty.

Technical specications of Akrapovič products are subject to change without notice.

Please read this entire installation manual carefully prior to installing and using the Akrapovič product.

GENERAL INFORMATION

COPYRIGHT AND OTHER RIGHTS NOTICE

The Akrapovič trademark, including corporate logos and emblems, are subject to copyright as well as trademark

rights of Akrapovič, its licensors, or third persons authorizing Akrapovič to use them.

Any reproduction, technical or other manipulation, translation, or other use of the copyright and/or trademark

rights contained herein is prohibited without the explicit prior written consent of Akrapovič. The same especially

applies to the entire contents of this manual and/or any of its parts, including but not limited to technical

specications, instructions, graphs, photographs, and so on included in this manual.

The shape of the Akrapovič product is protected under a registered Community Design No. RCD 015011323.

Akrapovič takes all copyright and other rights infringement cases under serious consideration. If you have any

reason to believe that your product is not an original Akrapovič product, please contact our local partners or

Akrapovič at [email protected].

3 / 14

YYWWPXXXXX

• THIS MANUAL IS SPECIFIC TO THE MOTORCYCLE INDICATED ON THE COVER PAGE, FOR WHICH IT IS

DESIGNED. INSTALLATION PROCEDURES VARY DEPENDING ON THE TYPE OF MOTORCYCLE. PLEASE

VERIFY THAT THE AKRAPOVIČ PRODUCT AND THIS INSTALLATION MANUAL CORRESPOND TO THE

TYPE OF YOUR MOTORCYCLE.

• FOR EXHAUST SYSTEM ONLY: THE EXHAUST SYSTEM CAN GET EXTREMELY HOT DURING AND AFTER

IT IS USED. MAKE SURE NOT TO TOUCH THE EXHAUST SYSTEM UNTIL IT IS COMPLETELY COOL.

ALLOW THE EXHAUST AND ENGINE TO COOL DOWN BEFORE BEGINNING INSTALLATION OR ANY

OTHER WORK ON THE MOTORCYCLE.

• MAKE SURE THE MOTORCYCLE IS SECURELY POSITIONED TO PREVENT TIPPING OVER AND DAMAGE

TO YOURSELF AND OTHERS, OR THE MOTORCYCLE.

• PLEASE CHECK THE PARTS YOU RECEIVED AGAINST THE PARTS LIST AVAILABLE ON OUR WEBSITE

(PLEASE USE THE QR CODE ON THE FRONT PAGE OR LOOK FOR “SCHEMATIC VIEW” IN THE

RESPECTIVE PRODUCT PAGE ON WWW.AKRAPOVIC.COM). MAKE SURE THAT YOU HAVE ALL THE

PARTS NECESSARY FOR THE INSTALLATION OF YOUR NEW AKRAPOVIČ PRODUCT. IF ANY OF THE

PARTS IS MISSING, PLEASE DO NOT PROCEED WITH UNINSTALLING YOUR STOCK PARTS/ INSTALLING

THE AKRAPOVIČ PRODUCT AND CONTACT THE RETAILER WHERE YOU PURCHASED THE AKRAPOVIČ

PRODUCT.

• ALWAYS CHECK YOUR MOTORCYCLE’S GROUND CLEARANCE. FOR ADVANCED USERS, WE

RECOMMEND YOU CHECK THE MOTORCYCLE SPRING PRELOAD SETTINGS TO OPTIMIZE GROUND

CLEARANCE WHERE POSSIBLE.

• FOR EXHAUST SYSTEM ONLY: EVERY EXHAUST SYSTEM MUFFLER HAS ITS UNIQUE SERIAL NUMBER,

WHICH IDENTIFIES THE AUTHENTICITY OF THE PRODUCT. YOU CAN FIND THE SERIAL NUMBER ON

THE MUFFLER’S INLET PIPE. PLEASE REFER TO THE PICTURE BELOW. PLEASE VERIFY THAT YOUR

EXHAUST SYSTEM IS AN ORIGINAL AKRAPOVIČ PRODUCT. IF YOU HAVE ANY DOUBTS, PLEASE CONTACT

THE RESELLER WHERE YOU PURCHASED THE EXHAUST SYSTEM OR AKRAPOVIČ PARTNERS. THIS

MANUAL, ANY CERTIFICATES AND AKRAPOVIČ WARRANTY APPLY TO ORIGINAL PRODUCTS ONLY.

SAFETY AND COMPLIANCE WARNING, PLEASE READ CAREFULLY

BEFORE REMOVING THE STOCK PARTS AND BEGINNING THE INSTALLATION OF YOUR NEW

AKRAPOVIČ PRODUCT, PLEASE MAKE SURE THAT ALL ITEMS LISTED BELOW ARE VERIFIED:

EXAMPLE OF SERIAL NUMBER POSITION

www.akrapovic.com

4 / 14

NOISE AND EMISSION WARNINGS

General warning

Because of the world-wide distribution of Akrapovič d.d. products, neither Akrapovič d.d. nor any of its subsidiaries

make any representation that the products comply with the air and/or noise emissions laws, or labeling laws, of

any jurisdiction. The purchasers are entirely responsible for informing themselves of the applicable laws where the

products are to be used and to comply with those law.

Although legal compliance of Akrapovič products in a specic country should be determined by the user, you can

nd some basic guidance on compliance of your Akrapovič product with various legal requirements on the product-

related part of our website (please use the QR code on the front page or look for the respective product page on www.

akrapovic.com). For EC and ECE type approvals, please refer to the certicate enclosed to your product.

California laws prohibit the use of any aftermarket part or system that modies, removes or replaces original equipment

catalysts unless the California Air Resources Board has issued an Executive Order regarding such part or system or

unless the part or system is exempted by being used only on racing vehicles on closed courses. Neither Akrapovic d.d.

nor any of their subsidiaries make any representation that any of their parts or systems has received such an Executive

Order or that any of their parts or systems conform with the racing vehicles exemption. The purchasers are entirely

responsible for informing themselves of applicable California laws and to comply with those laws.

Various U.S. states and the U.S. federal government have individual laws regulating the use of aftermarket parts and

systems, especially as those parts and systems modify, remove, or replace original equipment catalysts. Please consult

the appropriate laws in your area before installing any aftermarket part or system on your vehicle to ensure compliance

with all applicable laws. Neither Akrapovic d.d. nor any of their subsidiaries or the sellers of the parts or systems make

any representation that any of their parts or systems comply with any such laws.

USA WARNING

CALIFORNIA WARNING

CAUTION OR IMPORTANT

HAND TIGHTEN

INSTALLATION TIP

LUBRICATION

TOOLS AND PROTECTIVE

EQUIPMENT REQUIRED

TIGHTENING TORQUE

SYMBOLS

The following symbols are used throughout these installation instructions:

Photographs and other illustrations in this manual are symbolic and are intended to help represent individual steps

for proper installation and use, as well as for a general overview. The actual component parts of the Akrapovič

product may not entirely correspond to the photographs and other illustrations.

GENERAL NOTE

USE BOLT SEALANT

USE ANTI-SEIZE LEAD-FREE COPPER PASTE (black tube)

USE ANTI-SEIZING GREASE (white tube)

Apply 3 to 4 small drops of bolt sealant onto the cleaned and degreased threads before tightening the

bolts.

WARNING! Avoid contact with skin, eyes and mucous membranes. Do not inhale fumes. Keep

out of reach of children.

Provides trouble-free and long-lasting protection against seizing, corrosion and rusting of bolts,

threaded ends, nuts, joints, etc. Also protects against vibration, wear and impact.

Prevents seizing, corrosion and excessive wear between the titanium components.

WARNING! Avoid eye contact. Keep out of reach of children.

Tools & equipment

5 / 14

The packaging box should contain one or more of the following items:

• Akrapovič product

• Homologation certicate/ compliance documents if applicable

• Warranty

• Fitting material

• Installation Manual

Detailed list of parts can be found on the Akrapovič website (please use the QR code on the front page or look for

“Schematic view” in the respective product page on www.akrapovic.com).

PARTS LIST

• Mechanic gloves

• T-handle 4 mm hexagon wrench

• T-handle 6 mm hexagon wrench

• T-handle Torx 25 wrench

• T-handle Torx 40 wrench

• T-handle Torx 45 wrench

• T- handle swivelling 10 mm wrench

• Combination 13 mm wrench

REMOVAL OF STOCK EXHAUST SYSTEM OR OTHER STOCK MOTORCYCLE PARTS:

The process of uninstalling the original exhaust system or other motorcycle parts, may vary depending on

the existing exhaust system or other motorcycle parts. Please follow the motorcycle manufacturer’s workshop

manual for uninstalling the original exhaust system or other motorcycle parts.

If you for any reason decide otherwise, please note that any information provided in this respect herein should

be considered as general information provided for your convenience only. Akrapovič shall not assume any

liability or responsibility with regard to uninstalling your existing exhaust system or other parts of the motorcycle,

warranty coverage of such exhaust system or other motorcycle parts vehicle or their further tness for use.

In case your Akrapovič exhaust system or other motorcycle parts may not be used on certain roads or

under certain conditions, please keep the stock (or other) exhaust system or other stock parts that you

can use in such circumstances legally.

F 01

F 02

www.akrapovic.com

6 / 14

Put the motorcycle on a side stand, we recommend a central racing stand. Make sure, that surface is solid and ﬂat.

Unscrew marked bolts and carefully remove the heat shields o the motorcycle (F 01 ).

CAUTION: be careful not to injure yourself or damage any part of the motorcycle during this procedure!

1.

2.

Unscrew marked bolt and loosen marked clamps than carefully remove the muer o the motorcycle (F 02).

CAUTION: be careful not to injure yourself or damage any part of the motorcycle during this procedure!

3.

REMOVAL OF STOCK EXHAUST SYSTEM:

F 03

F 04

7 / 14

Assemble the bushes from Akrapovič installation kit onto the bracket, as shown (F 04).

CAUTION: be careful not to injure yourself or damage any part of the muer during this procedure!

2.

Assemble the muer’s inlet with the graphite gasket and clamp from Akrapovič installation kit, as shown (F 03).

CAUTION: be careful not to injure yourself or damage any part of the muer during this procedure!

1.

INSTALLATION OF THE AKRAPOVIČ EXHAUST SYSTEM:

F 05

F 06

www.akrapovic.com

8 / 14

Carefully slide the muer onto the pre muer, hand tighten it using bolt, washer and nut from Akrapovič installation

kit (F 05).

IMPORTANT: make sure not to damage the exhaust or any other part of the motorcycle during this process!

INSTALLATION TIP: for perfect positioning you can reposition the pre muer!

3.

Screw Akrapovič heat shield’s bolts and heat-resistant washers (Akrapovič installation kit) on Akrapovič heat shield

as shown (F 06, 07, 08).

INSTALLATION TIP: screw the heat resistant washers onto the bolts; do not try to push them on!

IMPORTANT

: heat resistant washers should be between carbon-ber heat shield and shield’s brackets, and

between bolts’ heads an carbon-ber heat shield!

4.

F 07

F 08

9 / 14

F 09

F 10

www.akrapovic.com

10 / 14

Install and tighten the heat shield onto the muer, as shown (F 09).

IMPORTANT: make sure not to damage any part of the exhaust system or motorcycle during this procedure!

5.

Position the muer in respect to the motorcycle, tighten the muer’s bracket bolt and clamp to the specied torques

(F 10, 11).

IMPORTANT: be careful not to injure yourself and any part of the motorcycle during this procedure!

6.

4.9Nm

3.6ftlb

22Nm

16ftlb

F 11

F 12

11 / 14

Tighten the pre muer’s clamps to the specied torques (F 12).

IMPORTANT: be careful not to injure yourself and any part of the motorcycle during this procedure!

7.

14Nm

10ftlb

9.8Nm

7.2ftlb

www.akrapovic.com

12 / 14

FINAL INSTALLATION:

MAINTENANCE OF THE AKRAPOVIČ PRODUCT:

Clean grease spots o all Akrapovič product’s surfaces, when installation is nished. Cleaning will prevent

spots from burning onto the surface. Do not use aggressive chemical cleaners, because they can damage

the surface or stickers:

Make sure all the nuts and bolts are suciently tightened. In case the Akrapovič product touches the cowling

or other parts, repeat the adjustment of the product or contact your authorized dealer.

Reinstall all dismounted or partially removed stock parts (cowlings, radiator etc); check vehicle manufacturer

workshop manual for correct procedures and tightening torques.

• Titanium surfaces (titanium muer’s outer sleeve, titanium pipes etc): use a soft cloth sprayed with a

multi-purpose spray lubricant (WD-40® or equivalent)*, then wipe with a soft dry cloth.

• Carbon-ber surfaces (carbon-ber outlet cap, carbon-ber muer’s outer sleeve, carbon-ber bracket

etc): use a soft dry cloth sprayed with all purpose foam cleaner, then wipe with a soft dry cloth.

• Painted surfaces (painted outlet cap, painted muer’s outer sleeve, painted bracket etc): use a soft

cloth sprayed with all purpose foam cleaner, then wipe with a soft dry cloth.

• Chrome plated surfaces (chrome plated outlet cap, chrome plated muer’s outer sleeve etc): use a soft

cloth sprayed with all purpose foam cleaner, then wipe with a soft dry cloth.

• Stainless steel surfaces (stainless steel muer’s outer sleeve, stainless steel pipes etc): use a soft

cloth sprayed with a contact cleaner, then wipe with a soft dry cloth.

IMPORTANT: periodically make sure all the bolts and springs are suciently tightened. In case

the product touches the cowling or other parts repeat the adjustment of the product or contact

your authorized dealer!

CAUTION: after running engine for 30 minutes, retighten the bolts of the Akrapovič carbon-ber

heat shield!

IMPORTANT: IT IS NORMAL IF WHITE SMOKE COMES OUT OF THE MUFFLER DURING THE

FIRST 100 KM AFTER REPLACEMENT.

IMPORTANT: A CHANGE IN THE COLOR OF THE EXHAUST SYSTEM IS NORMAL DUE TO THE

HIGH TEMPERATURES.

CAUTION: DO NOT STAND BEHIND THE MUFFLER AT ANY TIME.

IMPORTANT: DO NOT USE AUTOMOTIVE WHEEL CLEANERS OR ANY CLEANING PRODUCTS

WHICH CONTAIN ACIDIC ADDITIVES TO CLEAN AKRAPOVIČ PRODUCTS.

IMPORTANT: WE RECOMMEND HIGH CAUTION WHEN USING POWER / PRESSURE WASHER

FOR CLEANING PAINTED / LACQUERED SURFACES OF THE AKRAPOVIČ PRODUCTS, TO

AVOID PAINT / LACQUER DAMAGE.

IMPORTANT: ALL AKRAPOVIČ PRODUCTS ARE DEVELOPED AND DESIGNED TO BE USED ON

SPECIFIC VEHICLES, FOR THEIR ENTIRE EXPECTED LIFETIME. PLEASE MAKE SURE THAT

END-OF-LIFE AKRAPOVIČ PRODUCT IS DISASSEMBLED TO COMPONENTS SHOWN IN THE

PRODUCT’S SCHEMATIC DIAGRAM AVAILABLE ON THE AKRAPOVIČ WEBSITE AND EACH

COMPONENT SCRAPPED RESPONSIBLY AND ACCORDING TO APPLICABLE LOCAL LAWS

AND REGULATIONS. AKRAPOVIČ DOES NOT ASSUME ANY OBLIGATION OR RESPONSIBILITY

WITH RESPECT TO THE SCRAPPING PROCESS OR PROVIDING INFORMATION RELATED

THERETO.

*WD-40® is a trademark of the WD-40 Company.

1.

2.

3.

13 / 14

Exhaust gas leaks out of the

muer/pipe clamp connections

loosened clamp tighten the clamp to specied

torque

connection is not completely

joined

tap the connection into place and

tighten the clamp to specied

torque

TROUBLESHOOTING:

Problem Possible cause Solution

www.akrapovic.com

Numéro d‘article: KFT.22.995.30001/B Révision: 00 · Date: 11 - 2022

Support latéral PRO

 ~ 1 h. FACILE  DIFFICILE

FRANÇAIS ·Nous vous remercions d'avoir choisi ce produit haut de gamme de

SW-MOTECH. Visitez notre boutique en ligne pour plus d'informations (par

exemple affectation des modèles). Les documents nécessaires (par exemple

ABE) y sont disponibles en téléchargement.

Veuillez lire et prendre en compte toutes les instructions, les consignes de

sécurité et les avertissements contenus dans ce manuel de montage avant

de monter et d'utiliser le produit afin d'éviter toute blessure ou tout

dommage. Veuillez conserver la notice d'utilisation pour référence.

Ce produit a été développé pour des véhicules en configuration d'usine.

Nous ne sommes pas en mesure d'assurer la compatibilité avec les pièces

de rechange originales ou les pièces de rechange d'autres fabricants.

La présente notice d'installation a été élaborée conformément à nos

connaissances actuelles. Il n'existe aucun droit juridique à l'exactitude des

informations qu'elle contient. Sous réserve d'erreurs et de fautes. Sous

réserve de modifications techniques et conceptuelles. SW-MOTECH détient

les droits d'auteur.

SYMBOLE D'AVERTISSEMENT DE SÉCURITÉ

 Ce symbole d'avertissement est utilisé dans ces instructions de montage

pour mettre en garde contre des dangers mortels, de blessures ou d'autres

risques. Les mots DANGER, ATTENTION ou PRUDENCE sont utilisés avec ce

symbole d'avertissement pour transmettre des consignes de sécurité et des

informations importantes concernant le montage et l'utilisation de ce

produit. Ces mots, associés au symbole d'avertissement de sécurité,

signifient :

DANGER :signale une situation dangereuse pouvant entraîner la mort ou

des blessures graves si elle n'est pas évitée !

ATTENTION :signale une situation dangereuse pouvant entraîner la mort ou

des blessures graves si elle n'est pas évitée !

 PRUDENCE: Indique une situation dangereuse susceptible d'entraîner des

blessures de gravité réduite ou moyenne si elle se présente !

 REMARQUE : Informations importantes, mais qui n'entraînent pas de

risque de décès ou de blessure (dommages matériels uniquement).

REMARQUES GÉNÉRALES

 ATTENTION : le montage et/ou l'entretien de ce produit nécessite des

compétences techniques avancées, des outils appropriés et une bonne

compréhension de l'utilisation des outils et des indications de réglage. Pour

votre propre sécurité, SW-MOTECH recommande de confier le montage

et/ou l'entretien à un atelier de réparation de deux-roues qualifié et

certifié.

 ATTENTION : si vous décidez de monter vous-même ce produit, lisez

attentivement et intégralement les instructions de montage avant le

montage et l'utilisation et suivez toutes les instructions afin d'éviter des

blessures graves ou mortelles. Lors du montage et de l'utilisation, tenez

également compte de toutes les informations pertinentes du manuel du

véhicule. SI VOUS NE COMPRENEZ PAS UNE PARTIE DE CE MANUEL

D'INSTALLATION OU SI VOUS AVEZ BESOIN D'EXPLICATIONS CONCERNANT

UNE INSTRUCTION, N'ESSAYEZ PAS D'INSTALLER CE PRODUIT SANS

DEMANDER DE L'AIDE À SW-MOTECH !

PRÉPARATION : Veuillez lire attentivement les instructions de montage et

assurez-vous que tous les éléments de la liste de pièces sont présents.

 PRUDENCE :veillez à ce que votre véhicule soit bien stable. Éteignez le

moteur et retirez la clé de contact. Laissez refroidir le

moteur/l'échappement si nécessaire. Débranchez la batterie lorsque vous

travaillez sur le système électrique. Utilisez uniquement des outils

appropriés et portez toujours des lunettes de protection et des gants

pendant le montage et l'entretien. Faites-vous aider par une deuxième

personne lors du montage et de l'entretien.

MONTAGE : Toutes les pièces et connexions retirées du véhicule doivent

être réinstallées conformément aux instructions du fabricant du véhicule ou

remplacées par des pièces et du matériel fournis par SW-MOTECH.

 ATTENTION Sauf indication contraire, sécurisez tous les filetages avec

du frein filet liquide de force moyenne.

 DANGER : Les couples de serrage non définis par SW-MOTECH doivent

être obtenus auprès du constructeur du véhicule ou d'un atelier de

réparation de motos certifié.

CONTRÔLE DU FONCTIONNEMENT :Après le montage, assurez-vous

qu'aucune pièce mobile n'est bloquée et que le fonctionnement du véhicule

n'est pas perturbé. Les câbles et les tuyaux ne doivent pas frotter et/ou être

coincés.

 ATTENTION : Effectuez un contrôle de fonctionnement complet avant

de commencer à rouler. Après les 50 premiers kilomètres, puis

régulièrement, vérifiez le couple de serrage de tous les raccords et la

bonne fixation du produit. Les accessoires montés peuvent modifier le

comportement sur la route et la stabilité du véhicule.

INSTRUCTIONS DE MONTAGE · LIRE ET CONSERVER LES INSTRUCTIONS DE MONTAGE!

SW-MOTECH GmbH & Co. KG

Ernteweg 7-10

35282 Rauschenberg

Allemagne

   

 [email protected]

 www.sw-motech.com

La traduction du contenu est automatisée.

Sous réserve d'erreurs et de modifications

Sous réserve de modifications techniques et de design.

1

Vous trouverez les symboles et leur signification

dans la section MONTAGE. Si le terme OEM apparaît

dans la section MONTAGE, il faut respecter et

appliquer les consignes du fabricant du véhicule.

Si vous avez des questions, notre service clientèle ainsi

que nos distributeurs se tiennent à votre disposition. Vous

trouverez notre numéro de téléphone ainsi que la liste de

nos distributeurs sur notre boutique en ligne :

www.sw-motech.com

Utilisez du frein filet : Indique qu'un filetage doit être

enduit de frein filet liquide. H (HIGH) : haute

résistance ; M (MEDIUM) : force moyenne ; L (LOW) :

faible résistance.

Serrer en respectant les instructions de couple de

serrage : indique le couple de serrage d'une pièce

prescrit par SW-MOTECH ou par le fabricant du véhicule

(OEM).

Ne pas utiliser de frein filet : signifie que l'utilisation

d'un frein filet liquide n'est pas nécessaire à ce

stade.

APERçU DES LéGENDES · LIRE ET CONSERVER LES INSTRUCTIONS DE MONTAGE!

La traduction du contenu est automatisée.

Sous réserve d'erreurs et de modifications

Sous réserve de modifications techniques et de design.

2

LISTE DES PIèCES · LIRE ET CONSERVER LES INSTRUCTIONS DE MONTAGE!

La traduction du contenu est automatisée.

Sous réserve d'erreurs et de modifications

Sous réserve de modifications techniques et de design.

3

21

KFT.22.822.001.11

2/2

2

M8 x 40; DIN 912

SC.ST.08.040.48.912.109

4/4

3

KFT.05.440.007.11

4/4

4

M8 x 35; DIN 6912

SC.ST.08.035.02.6912.088

4/4

5

ø 8,4; DIN 125

US.ST.084.02.125

4/4

6

Ø 20 / Ø 8,4 / h 14,5

DB.ST.0200.0084.0145.02

4/4

37

KFT.06.525.005.11

1/1

8

M6 x 25; ISO 7380

SC.ST.06.025.02.7380.109

3/3

9

Ø 20 / Ø 6,4 / h 5

DB.ST.0200.0064.0050.02

1/1

10

M6; DIN 6927

MU.ST.06.02.6927.08

3/3

411

KFT.22.995.971.01.11

1/1

12

KFT.22.995.972.01.11

1/1

13

KFT.00.152.SV.8

1/1

1

AVERTISSEMENT : portez toujours des lunettes et des gants de protection

!

AVERTISSEMENT : utilisez toujours des outils adaptés !

Retirez les vis indiquées des deux côtés du véhicule, et démontez les repose-

pieds passager.

PHASE DE MONTAGE · LIRE ET CONSERVER LES INSTRUCTIONS DE MONTAGE!

La traduction du contenu est automatisée.

Sous réserve d'erreurs et de modifications

Sous réserve de modifications techniques et de design.

4

2

1×2

2×4

M 23 Nm

3×4

4×4

M 23 Nm

5×4

6×4

Vissez les plaques de montage (1) aux repose-pieds passager des deux côtés

du véhicule.

AVERTISSEMENT : Utilisez du frein filet liquide !

Ne serrez pas encore les vis (2).

Vissez les plaques de montage (3) des deux côtés de l'arrière du véhicule.

AVERTISSEMENT : Utilisez du frein filet liquide !

Ne serrez pas encore les vis (4).

 Remarque : Pour monter le support latéral au le porte-bagages SW-

MOTECH,utiliser les entretoises de porte-bagages (*) comme indiqué sur le

schéma détaillé.

PHASE DE MONTAGE · LIRE ET CONSERVER LES INSTRUCTIONS DE MONTAGE!

La traduction du contenu est automatisée.

Sous réserve d'erreurs et de modifications

Sous réserve de modifications techniques et de design.

5

La page charge ...

SW-Motech KFT.22.995.72000/S Mounting instructions

SW-Motech KFT.22.995.72000/S Mounting instructions

dans d''autres langues

Documents connexes

Autres documents