1
Quick Setup Guide
SK300 Smart Kiosk
PAX TECHNOLOGY LIMITED
2
1. Checklist
Congratulations on receiving your PAX Technology payment terminal. We do hope you
enjoy it! The box you have just opened should contain the following items:
• 1 x PAX SK300 Smart Kiosk
• 1 x SK300 Hanging bracket
• 1 x Thermal Paper Roll
• 4 x M2.5*4 Combination Screw
• 1 x Power Adapter
• 1 x Power Supply cable
• 1 x Small screwdriver with cross slot (for SK300)
• 4 x ST5.0X40-PB Cross recessed countersunk head tapping screws with tip
• 4 x Screw expand rubber plug(5.0x40 self-tapping screw dedicated)
2. Product Description
3
3. Operating Instruction
Power on: Plug in the AC power cable, press and hold the Power
button for three seconds until the boot animation appears.
Power off: Press and hold the Power button for three seconds until the
shutdown menu displays. Select Power off. The terminal turns off after a
few seconds.
4. Payment Options
Magnetic stripe card: Insert magnetic stripe card into card slot and
push to the end with magnetic stripe facing down, then pull out the card
at a constant speed to swipe card.
4
IC chip card: Insert card with IC chip facing up, then push it to the end
of the card slot. Leave card inserted until prompted to remove.
Contactless card: Place the contactless card over the center of
contactless card reader logo area.
5
Scan: When the scan indicator is on, hold your QR code & bar code
device in front of the scan window to scan code.
5. Load Printer Paper
Completely open the printer cover, Insert the new paper roll into the
printer, Close the printer cover.
6. Desktop Installation
Completely open the printer cover, Insert the new paper roll into the
printer, Close the printer cover.
Parts List
6
7. Wall-mounted Installation
Parts List
7
8. Usage Tips
There is no built-in battery, and the device can only be powered by the
power adapter.
Avoid exposing the device in overheated, humid, dusty, or strong
electromagnetic environment.
Do not vibrate, shake, or drop the device.
Do not insert or unplug any part of the device while it is powered on.
Otherwise, it may cause damage to the internal circuit.
If necessary, please contact PAX technical support for assistance with
the device.
Before using the magnetic stripe /IC/contactless card, check if there is
any suspicious person nearby, if so, pay attention to guard against theft.
9. Environmental Parameters
8
Working Environment：Temperature:-10℃～50℃(32℉～113℉)
(non-charging)
Storage Environment：Temperature:-20℃～70℃(-4℉～158℉)
(non-charging)
Humidity：5%～96% (non-condensing)
10. Icons
Dispose in a professional recycling manner
Class II equipment
For indoor use only
Energy efficiency marking
AC voltage
DC voltage
microSD logo
Trademark notice:
microSD logo is a trademark of SD-3C LLC.
FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
To comply with RF exposure requirements, a minimum separation distance of 20mm
must be maintained between the user’s body and the device, including the antenna.
IC STATEMENT
This device complies with Industry Canada Unlicence-exempt RSS standard(s)
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. End user must follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be co-located or operating in conjunction
withany other antenna or transmitter.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio
exempts de licence.Ce dispositif est conforme aux normes autoriser-exemptes du
Canada RSS d'industrie L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.Cet équipement
est conforme avec l'exposition aux radiations IC définies pour un environnement
9
10
non contrôlé. L'utilisateur final doit respecter les instructions de fonctionnement
spécifiques pour satisfaire la conformité aux expositions RF. Cet émetteur ne doit pas être
co-localisées ou opérant en conjonction avec une autre antenne ou transmetteur. Ces
exigences définissent
To comply with RF exposure requirements, a minimum separation distance of 20mm
must be maintained between the user’s body and the device, including the antenna.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
