PAX E600Mini Manuel utilisateur

Marque: PAX

Modèle: E600Mini

Taper: Manuel utilisateur

E600Mini Integrated Smart Terminal

PAX TECHNOLOGY LIMITED

1. Contents Checklist

Please check the components after unpacking. If any one of them is missing, or if

there is a page missing from the product manual,etc., please contact the dealer.

Name

Qty.

E600Mini

AC Power Adapter

AC Power Cable

Product Manual

2. Product Description

3. Installation

Power on: Press and hold the Power button for three seconds until the main screen

displays normally.

Power off: Press and hold the Power button for three seconds until the shutdown

menu appears, tap “Shutdown”, and then “shutting...” appears. The terminal will be

turned off after a few seconds.

Swipe the magnetic stripe card: Place the magnetic stripe face down (keep the

magnetic stripe card perpendicular to the main display), swipe card through the

magnetic card slot at a constant speed.

IC Card: Place the IC chip face down, then insert the IC card into the card slot, and

push it to the end.

Contactless card: Put the contactless card on the center of the payment module

screen.

Tear paper: Press the print paper downward along the cutter and tear it leftward or

rightward when getting close to the main display.

Charge: Insert the external adapter or the base to charge the device, the indicator

lighting in red means the device is charging; the indicator lighting in green means

charging is completed; the indicator flashing in red and green alternately means

charging is abnormal.

Insert SIM/ microSD card: Take the Card Pick-up needle out of the box，insert the

Card Pick-up needle into the SIM/mircoSD card slot.

4. Specification

Operating System: Android 10.0

CPU: Cortex A55 Octa-Core, 1.6GHz

Memory: 2GB RAM + 16GB Flash Memory

Display: 7" inch, resolution: 600*1024, multi-touch capacitive touch screen

Printer: 2" high-speed thermal printer, support 58*30mm print paper roll

Audio: Built-in speaker, support headphone output

Camera: camera, 30W-pixel, fixed-focus, high-speed code scanning

L-Sensor (Ambient Light Sensor): Automatically adjust the backlight brightness of

the main display

Wireless Communication: Support Wi-Fi® , Bluetooth® wireless technology, 3G/4G

Positioning: Support GPS, Compass, Gingileo, GLONASS

Card Slots: SIM card slot

microSD card slot（maximum supports 128GB）

magnetic stripe card/IC card slot, using two-in-one（support MAG&ICC）

Magnetic Card Reader: Support track 1/2/3.

IC Card Reader: Conform to the standard of ISO7816, EMV2000 L1&L2, PBOC3.0

Contactless Card Reader: Compatible with ISO14443 Type A&B

Working Environment Temperature: 0℃～50℃(32℉～122℉)

R.H.: 10%～93% (non-condense)

Storage Environment Temperature:-20℃～70℃(-4℉～158℉)

R.H.:5％～95％ (non-condense)

5. Cautions of installation and usage

1）Avoid exposing the terminal in hot, humid, dusty or strong electromagnetic

environment.

2）Do not violently vibrate, shake or beat the product.

3）Do not plug/unplug any units of the product when it is power on, otherwise it may

damage the internal circuit.

4）Do not maintain the terminal if you are non-professional

5）Before inserting the magnetic stripe/IC/contactless card, please check whether there

is any foreign object inside or surround the card slot , and if any , report to related

personnel.

Caution

Risk of explosion if battery replaced by an incorrect type.

Dispose of used batteries according to the instructions.

Hereby, PAX Computer Technology (Shenzhen) Co., Ltd. declares that the radio

equipment type E600Mini is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet

address：https://www.pax.com.cn/ProductCE/index.aspx

Icon shows

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic

equipment (WEEE). This means that this product must be handled pursuant to

European directive 2012/19/EU in order to be recycled or dismantled to minimize its

impact on the environment.

User has the choice to give his product to a competent recycling organization or to the

retailer when he buys an new electrical or electronic equipment.

The symbol indicates DC voltage

microSD logo

Trademark notice:

“microSD logo is a trademark of SD-3C LLC.”

“The Bluetooth® word mark and logos are registered trademarks owned by

Bluetooth SIG, Inc. and any use of such marks by PAX Technology Limited is under

license. Other trademarks and trade names are those of their respective owners.”

P/N：200312000000337

PAX TECHNOLOGY LIMITED reserves

the right to change product technology

specifications without notifying.

PAX TECHNOLOGY LIMITED

Manufacturer: PAX Computer Technology (Shenzhen) Co.,Ltd.

Address: 4/F, No.3 Building, Software Park, Second Central Science-Tech Road,

High-Tech Industrial Park, Shenzhen, Guangdong, P.R.C.

Tel: 0755-86169630 Fax: 0755-86169634

Website: http://www.pax.com.cn

FCC Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired

operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

SAR Information Statement

Your wireless Countertop Payment Terminal is a radio transmitter and receiver. It is designed and

manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the

Federal Communications Commission of the U.S. Government. These limits are part of comprehensive

guidelines and establish permitted levels of RF energy for the general population. The guidelines are

based on standards that were developed by independent scientific organizations through periodic and

thorough evaluation of scientific studies. The standards include a substantial safety margin designed to

assure the safety of all persons, regardless of age and health. The exposure standard for wireless mobile

Countertop Payment Terminals employs a unit of measurement known as the Specific Absorption Rate, or

SAR. The SAR limit set by the FCC is 1.6 W/kg. * Tests for SAR are conducted with the Countertop Payment

Terminal transmitting at its highest certified power level in all tested frequency bands. Although the SAR

is determined at the highest certified power level, the actual SAR level of the Countertop Payment

Terminal while operating can be well below the maximum value. This is because the Countertop Payment

Terminal is designed to operate at multiple power levels so as to use only the power required to reach the

network. In general, the closer you are to a wireless base station antenna, the lower the power output.

Before a Countertop Payment Terminal model is available for sale to the public, it must be tested and

certified to the FCC that it does not exceed the limit established by the government adopted requirement

for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the

body) as required by the FCC for each model. The highest SAR value for this model Countertop Payment

Terminal when tested for use on the body, as described in this user guide, is 2.717W/Kg(Body-worn

measurements differ among Countertop Payment Terminal models, depending upon available accessories

and FCC requirements). While there may be differences between the SAR levels of various Countertop

Payment Terminals and at various positions, they all meet the government requirement for safe exposure.

The FCC has granted an Equipment Authorization for this model Countertop Payment Terminal with all

reported SAR levels evaluated as in compliance with the FCC RFexposure guidelines. SAR information on

this model Countertop Payment Terminal is on file with the FCC and can be found under the Display Grant

section of http://www.fcc.gov/ oet/fccid after searching on

FCC ID: V5PE600MINI Additional information on Specific Absorption Rates (SAR) can be found on the

Cellular Telecommunications Industry Asso-ciation (CTIA) web-site at http://www.wow-com.com. * In the

United States and Canada, the SAR limit for mobile Countertop Payment Terminals used by the public is

1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a sub-stantial margin of

safety to give additional protection for the public and to account for any variations in measurements.

Body-worn Operation

This device was tested for typical body-worn operations. To comply with RF exposure requirements, a

minimum separation distance

of 0mm must be maintained between the user’s body and the handset, including the antenna.

Third-party belt-clips, holsters,

and similar accessories used by this device should not contain any metallic components. Body-worn

accessories that do not meet these requirements may not comply with RF exposure requirements and

should be avoided. Use only the supplied or an approved antenna.

IC STATEMENT

This device complies with Industry Canada licence-exempt RSS standard(s)

Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause undesired

operation of the device.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment. End user must follow the specific operating instructions for satisfying RF

exposure compliance. This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue.

The highest SAR value for this model when worn on the body is 0.23W/Kg. This device was tested for

typical body-worn operations. To comply with RF exposurerequirements, a minimum separation distance

of 0mm must be maintained between the

user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar

accessories used by this device should not contain any metallic components. Body-worn

accessories that do not meet these requirements may not comply with RF exposure

requirements and should be avoided. Use only the supplied or an approved antenna.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio

exempts de licence.

Ce dispositif est conforme aux normes autoriser-exemptes du Canada RSS d'industrie

L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.Cet équipement

est conforme avec l'exposition aux radiations IC définies pour un environnement

non contrôlé. L'utilisateur final doit respecter les instructions de fonctionnement spécifiques pour

satisfaire la conformité aux expositions RF. Cet émetteur ne doit pas être co-localisées

ou opérant en conjonction avec une autre antenne ou transmetteur.Ces exigences définissent

la valeur SAR limite à 1.6 W / kg en moyenne par gramme de tissu.La valeur SAR la plus élevée pour ce

modèle lorsque porté sur le corps est 2.717W/Kg.

Cet appareil a été testé pour des opérations portés sur le corps typiques. Pour se conformer

aux exigences d'exposition aux radiofréquences, une distance minimale de 0mm doit être

maintenue entre le corps de l'utilisateur et le combiné, y compris l'antenne. Les pinces de

ceinture, les étuis et autres accessoires similaires utilisés par cet appareil ne doivent pas

contenir de composants métalliques. Les accessoires portatifs qui ne répondent pas à ces

exigences peuvent ne pas se conformer aux exigences d'exposition RF et doit être évitée.

Utilisez uniquement l'antenne fournie ou une antenne approuvée

PAX E600Mini Manuel utilisateur

Marque: PAX

Modèle: E600Mini

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: PAX E600Mini User manual

PAX E600Mini Manuel utilisateur

PAX E600Mini Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents