1
A35 POS Terminal User Manual
Note: Product images shown may be different than actual product received
PAX TECHNOLOGY LIMITED
2
1. Product Description
LCD Display
Contactless Card Reader
Keypad
Privacy Shield
Camera
Magstripe Card Reader
Smart card reader
3
2. Specifications
Model A35
Processor Quad-core Cortex A53, 1.6GHz
Memory 8GB Flash + 1GB DDR, 128GB MicroSD Optional
Display 4'' WVGA 480 x 800 Pixels, Capacitive Touch Screen
Keys / Buttons 13 keys: 0-9 | Enter | Clear | Cancel, Back-Lighting (Optional)
Cards Handle Chip & PIN | NFC Contactless | Magnetic Stripe
Cameras 0.3MP Fixed Front-Facing, 5MP Fixed Front-Facing Optional
Audio 1 Speaker | 1 Audio Jack
Communications RS232 | Ethernet (Gigabit Optional) | USB 2.0 |
Wi-Fi® (2.4GHz / 5GHz ) + Bluetooth® (4.2/5.0) (Optional)
Ports Multi-Functional Port |1 Kensington | MicroSD (Optional)
SIM/SAM Up to 2 PSAM
Power Supply Input: 100-240VAC, 50Hz/60Hz | Output: 5.0V DC, 1.0A
Physical 163.69mm x 76.90mm x 30.10mm(L x W x H)
Accessories Multiple Cabling Options | Stand
Environmental 0°C ~ 50°C (32°F ~ 122°F) Operating Temperature
-20°C ~ 70°C (-4°F ~ 158°F) Storage Temperature
5% ~ 93% Relative Humidity, Non-Condensing
3.Instructions
A35 connects to a POS or an ECR by a communication cable for entering password，taping
contactless card, swiping magstripe card, inserting smart card or reading 1D/2D code during
transaction process. To use it correctly, you should refer to following instructions:
1) Power Connections
Power can be supplied to the A35 by connecting the AC power adapter to the communication
cable, as in the case of RS232 or USB configurations, or via a powered USB cable (12V Powered
USB) where the connected POS terminal provides the power.
2) Reset
Press and hold the 'X' and ‘O’ button for 5-8 seconds, the operation system will reboot.
3) Communication cable
① Remove the back cover (At the bottom of the terminal).
② Put the communication cable head to the Type-C interface.
4) SAM Cards
① Remove the back cover (At the bottom of the terminal).
② Insert the SAM cards to the corresponding card slot.
5) SD Card
① Remove the back cover (At the bottom of the terminal).
② Insert the SD card to the corresponding card slot.
6) Magnetic stripe card reader
To use the magnetic stripe card reader, put magnetic stripe side of magnetic card towards device
interior, swipe the card with a steady speed during through magnetic reader slot. (Support
bi-directional swiping).
4
7) IC card reader
To use the IC card reader, put IC card chip side upward, push in IC card slot and to bottom.
8) Contactless card reader
To use the contactless card reader, tap the contactless card on the Top LCD screen area of the
device, indicated by the universal contactless icon on the screen, when prompted.
9) 1D/2D code reader
To use the 1D/2D code reader, put the 1D/2D code toward the top center area of the LCD.
10) Electronic signature
A35 supports electronic signature. Please be sure to use the finger to sign, do not use metal or
sharp objects to operate the touch screen, so as not to damage the touch screen.
11) Terminal Anti-theft
A35 provides a Kensington security hole on the rear side of the terminal, the end users can lock
the terminal on the countertop with a Kensington lock if necessary.
12) Audio Jack
If required, a visually disabled person can connect a headphone to the terminal for audio
prompting if the terminal application supports this using the 3.5mm output audio jack.
4. Installation and Usage Tips
1）Avoid putting the terminal in direct sunlight, high temperature, moist, or dusty environment.
2）Forbid non-professional to repair the terminal.
3）Before insert the card, please check internal and around of IC card slot . when you found some
suspicious objects , must report to related administrator.
5. Password Entering Tips
It is highly recommended to enter password as following ways:
1）Set up anti-peep shields. Enter password with shield by the structures of cashier desk.
2）Place the POS terminal at an appropriate angle and make sure it is difficult to peer the password.
For example, the POS was installed above the movable bracket.
3）In enter password perspective, avoid surrounding video surveillance.
4）Paste text instructions to remind the customers to shelter with body or palm when enter
password.
5）Merchants can also choose other ways to protect the customer input password.
FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This device has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
5
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiated radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate the equipment.
RF Exposure Information
This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for exposure
to radio frequency (RF) energy set by the Federal Communications Commission of the
U.S. Government.
This device complies with FCC radiation exposure limits set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency
exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches)
during normal operation.
ISED Notice
This device complies with Innovation, Science and Economic Development Canada
license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes:
6
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en
IC: 11689A-A35DBW
ISED RF Exposure Statement
This device complies with ISED RSS-102 RF exposure limits set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the IC RSS-102 RF exposure
limits, human proximity to the antenna shall not be less than 20cm (8 inches) during
normal operation.
Cet appareil est conforme aux limites d'exposition aux rayonnements de la CNR-102
définies pour un environnement non contrôlé. Afin d'éviter la possibilité de dépasser les
limites d'exposition aux fréquences radio de la CNR-102, la proximité humaine à l'antenne
ne doit pas être inférieure à 20 cm (8 pouces) pendant le fonctionnement normal.
PAX TECHNOLOGY LIMITED reserves the right to change
product technology specifications without notifying.
PAX TECHNOLOGY LIMITED
Manufacturer: PAX Computer Technology (Shenzhen) Co., Ltd.
Address:4/F, No.3 Building, Software Park, Second Central Science-Tech Road,
High-Tech Industrial Park, Shenzhen, Guangdong, P.R.C.
Tel: 0755-86169630 Fax: 0755-86169634
Website: http://www.pax.com.cn
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail, Building 400, 3rd Floor Suite 300, Jacksonville ,
Florida, USA 32256
Help-desk
1 877-859-0099
-
1
-
2
-
3
-
4
-
5
-
6
