Hitachi WH12DM Safety Instructions And Instruction Manual

MODEL Variable speed

CORDLESS IMPACT DRIVER

MODÈLE

VISSEUSE À PERCUSSION

MODELO

ATORNILLADORES DE PERCUSION A BATERÍA

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner

la mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de

ce produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser

l’outil motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs

et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être

conservé dans un endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read

and understand this manual BEFORE operating the power tool. Please keep this

manual available for other users and owners before they use the power tool. This

manual should be stored in safe place.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede

resultar en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde

este manual para que puedan leerlo otras personas antes de utilizar la herramienta

eléctrica. Este manual debe ser guardado en un lugar seguro.

WH 12DM

•

WH 9DM

CONTENTS

English

Page

IMPORTANT SAFETY INFORMATION ............... 3

MEANINGS OF SIGNAL WORDS....................... 3

SAFETY .................................................................... 4

GENERAL SAFETY RULES – FOR ALL

BATTERY OPERATED TOOLS ..................... 4

SPECIFIC SAFETY RULES ................................... 6

IMPORTANT SAFETY INSTRUCTIONS FOR

USE OF THE CORDLESS IMPACT DRIVER .......

7

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER............................ 7

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER .................................... 8

FUNCTIONAL DESCRIPTION ................................ 10

MODEL ............................................................... 10

NAME OF PARTS .............................................. 10

TABLE DES MATIERES

ÍNDICE

Página

ESPECIFICACIONES ............................................ 58

MONTAJE Y OPERACIÓN....................................... 59

APLICACIONES ................................................... 59

MÉTODO DE EXTRACCIÓN E INSTALACIÓN

DE LA BATERÍA ............................................ 59

MÉTODO DE CARGA .......................................... 59

ANTES DE LA UTILIZACIÓN .............................. 62

OPERACIÓN ......................................................... 62

PRECAUCIONES OPERACIONALES .................. 65

MANTENIMIENTO E INSPECCIÓN ........................ 67

ACCESORIOS ........................................................... 70

ACCESORIOS ESTÁNDAR.................................. 70

ACCESORIOS OPCIONALES .............................. 70

Page

SPECIFICATIONS .............................................. 11

ASSEMBLY AND OPERATION ............................. 12

APPLICATIONS.................................................. 12

REMOVAL AND INSTALLATION METHOD

OF BATTERY .................................................. 12

CHARGING METHOD........................................ 12

BEFORE USE ..................................................... 15

OPERATION ....................................................... 15

OPERATIONAL CAUTIONS .............................. 17

MAINTENANCE AND INSPECTION ..................... 20

ACCESSORIES ....................................................... 22

STANDARD ACCESSORIES ............................. 22

OPTIONAL ACCESSORIES ............................... 22

Page

INFORMATIONS IMPORTANTES DE SÉCURITÉ

.. 25

SIGNIFICATION DES MOTS D’AVERTISSEMEN

T .... 25

SECURITE ................................................................ 26

REGLES GENERALE DE SECURITE – POUR TOUS

LES OUTILS FONCTIONNANT SUR BATTERIE ...

26

REGLES DE SECURITE SPECIFIQUES ............... 28

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR

L'UTILISATION DU VISSEUSE À PERCUSSION À BATTERIE

29

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR L’UTILISATION DU CHARGEUR DE BATTERIE ...

30

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR L’UTILISATION

DE LA BATTERIE ET DU CHARGEUR DE BATTERIE ...............

31

DESCRIPTION FONCTIONNELLE ........................... 33

MODELE ............................................................... 33

NOM DES PARTIES............................................. 33

Page

SPECIFICATIONS ................................................ 34

ASSEMBLAGE ET FONCTIONNEMENT ..........................

35

UTILISATIONS ..................................................... 35

MÉTHODE DE RETRAIT ET D’INSTALLATION

DE LA BATTERIE .......................................... 35

MÉTHODE DE RECHARGE ................................. 35

AVANT L’UTILISATION ...................................... 38

UTILISATION ....................................................... 38

PRÉCAUTIONS D'UTILISATION......................... 41

ENTRETIEN ET INSPECTION .................................. 43

ACCESOIRES ........................................................... 46

ACCESSOIRES STANDARD ............................... 46

ACCESSOIRES EN OPTION ................................ 46

Français

Español

Página

INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD

.... 49

SIGNIFICADO DE LAS PALABRAS DE SEÑALIZACIÓN

.. 49

SEGURIDAD ............................................................. 50

NORMAS GENERALES DE SEGURIDAD – PARA TODAS

LAS HERRAMIENTAS ALIMENTADAS CON BATERÍA

.. 50

NORMAS ESPECÍFICOS DE SEGURIDAD ......... 52

INSTRUCCIONES IMPORTANTES PARA LA UTILIZACIÓN

DEL ATORNILLADORES DE PERCUSION A BATERÍA

.. 53

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA EL CARGADOR DE BATERÍAS

................. 54

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA LA BATERÍA Y EL CARGADOR DE BATERÍAS

... 55

DESCRIPCIÓN FUNCIONAL .................................... 57

MODELO .............................................................. 57

NOMENCLATURA ............................................... 57

English

3

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and

in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in

death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in

minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

English

4

SAFETY

GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock,

fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the

dust of fumes.

(3) Keep bystanders children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety

(1) A battery operated tool with integral batteries or a separate battery pack must be

recharged only with the specified charger for the battery.

A charger that may be suitable for one type of battery may create a risk of fire when

used with another battery.

(2) Use battery operated tool only with specifically designed battery pack.

Use of any other batteries may create a risk of fire.

3. Personal Safety

(1) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in

serious personal injury.

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing and gloves away from moving parts. Loose clothes, jewelry, or long hair

can be caught in moving parts.

(3) Avoid accidental starting. Be sure switch is off position before inserting battery.

Carrying tools with your finger on the switch or inserting the battery pack into a tool

with the switch on invites accidents.

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enable better control of the tool in unexpected situations.

(6) Use safety equipment. Always wear eye protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection must be used for appropriate conditions.

English

5

4. Tool Use and Care

(1) Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to

loss of control.

(2) Do not force tool. Use the correct tool for your application. The correct tool will do

the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

(4) Disconnect battery pack from tool or place the switch in the locked or off position

before making any adjustments, changing accessories, or storing the tools. Such

preventive safety measures reduce the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

(6) When battery pack is not in use, keep it away from other metal objects like: paper

clips, coins, keys, nails, screws, or other small metal objects that can make a

connection from one terminal to another.

Shorting the battery terminals together may cause sparks, burns, or a fire.

(7) Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

(8) Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tools operation. If damaged, have the tool serviced

before using. Many accidents are caused by poorly maintained tools.

(9) Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on

another tool.

5. Service

(1) Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

(2) When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to follow

Maintenance Instruction may create a risk of electric shock or injury.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construc-

tion activities contains chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type

of work. To reduce your exposure to these chemicals: work in a well ventilated area,

and work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

English

6

SPECIFIC SAFETY RULES

1. Hold tools by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring. Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the operator.

2. Never touch moving parts.

Never place your hands, fingers or other body parts near the tool’s moving parts.

3. Never operate without all guards in place.

Never operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or safety

feature, be sure to replace the guard or safety feature before resuming operation of the

tool.

4. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw for cutting

tree limbs or logs.

5. Never use a power tool for applications other than those specified.

Never use a power tool for applications other than those specified in the Instruction

Manual.

6. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or throw the

tool. Never allow the tool to be operated by children, individuals unfamiliar with its

operation or unauthorized personnel.

7. Definitions for symbols

V .... volts

---

— ............. direct current

n

o

............ no load speed

---/min ..... revolutions or reciprocation per minute

8. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

9. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not

be used until repaired.

10. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to youself or others. Blades, cutting implements and accesso-

ries which have been mounted to the tool should be secure and tight.

11. Never use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

12. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may be

deformed, cracked, or damaged.

13. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

English

7

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE

CORDLESS IMPACT DRIVER

WARNING: Death or serious bodily injury could result from improper or unsafe use

of the cordless impact driver. To avoid these risks, follow these basic

safety instructions:

1. Never use this driver handle for any application other than those in this manual.

2. Never place hands or other body parts near the drill bit or chuck during operation.

Hold the impact driver by its handle only.

3. When working in high places, always make sure that ther is no one below before starting

to work.

4. Always wear eye and ear protection when you work.

5. Always install the driver bit securely. A loose bit is dangerous because it can come loose

while you are working.

6. Always use the driver bit that matches the screw size.

7. Always have the screw you are screwing in and this impact driver in a straight line.

Working with this impact driver at an angle to the screw can damage the screw head and

will not give the prescribed tightening torque.

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER

1. This manual contains important safety and operating instructions for battery charger

Model UC14YF2.

2. Before using battery charger, read all instructions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

3. To reduce risk of injury, charge HITACHI rechargeable battery type EB7, EB9, EB12, EB14

series. Other type of batteries may burst causing personal injury and damage.

4. Do not expose battery charger to rain or snow.

5. Use of an attachment not recommended or sold by the battery charger manufacturer may

result in a risk of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug when disconnecting

battery charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same number, size, and shape as those of plug

on battery charger:

b. That extension cord is properly wired and in good electrical condition; and

c. That wire size is large enough for AC ampere rating of battery charger as specified

in Table 1.

English

8

* If the input rating of a battery charger is given in watts rather than in amperes, the

corresponding ampere rating is to be determined by dividing the wattage rating by the

voltage rating–for example:

9. Do not operate battery charger with damaged cord or plug-replace them immediately.

10. Do not operate battery charger if it has received a sharp blow, been dropped, or

otherwise damaged in any way; take it to a qualified serviceman.

11. Do not disassemble battery charger; take it to a qualified serviceman when service or

repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

12. To reduce risk of electric shock, unplug charger from receptacle before attempting any

maintenance or cleaning. Removing the battery will not reduce this risk.

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE

BATTERY AND BATTERY CHARGER

You must charge the battery before you can use the cordless impact wrench. Before using

the model UC14YF2 battery charger, be sure to read all instructions and cautionary

statements on it, the battery and in this manual.

REMEMBER: USE ONLY HITACHI BATTERY TYPES EB7 SERIES, EB9 SERIES, EB12 SERIES,

EB14 SERIES. OTHER TYPES OF BATTERIES MAY BURST AND CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING: Improper use of the battery or battery charger can lead to serious injury.

To avoid these injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged or is completely worn out. The

battery can explode in a fire.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s air vents. Electric shock or

damage to the battery charger may result.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or but less Length of Cord, Feet (Meter)

greater than than 25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

1250watts

125 volts

= 10 amperes

English

9

5. NEVER charge outdoors. Keep the battery away from direct sunlight and use only

where there is low humidity and good ventilation.

6. NEVER charge when the temperature is below 32°F (0°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to charge.

11. NEVER store the battery or battery charger in places where the temperature may

reach or exceed 104°F (40°C).

12. ALWAYS operate charger on standard household electrical power (120 volts). Using

the charger on any other voltage may overheat and damage the charger.

13. ALWAYS wait at least 15 minutes between charges to avoid overheating the charger.

14. ALWAYS disconnect the power cord from its receptacle when the charger is not in use.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

English

10

MODEL

WH12DM: with charger (UC14YF2) and case

WH9DM: with charger (UC14YF2) and case

NAME OF PARTS

1. Cordless Impact Driver

䡬 Battery

FUNCTIONAL DESCRIPTION

NOTE: The information contained in this Instruction Manual is designed to assist you in the

safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read

and understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that

differ from those on your own power tool.

Nameplate

Switch Trigger

Handle

Battery

Push Button

Housing

Air Vents

Convenient

Hook

EB9BEB1220BL

Fig. 1

Latch

Nameplate

Terminal

Hole

Latch

Terminal

Hole

Nameplate

English

11

2. Battery Charger (UC14YF2)

SPECIFICATIONS

1. Cordless Impact Driver

Input power source Single phase: AC120V 60Hz

Charging time Approx. 60min. (At a temperature of 68°F (20°C))

Charger

Charging voltage .......................... DC 7.2–14.4V

Charging current........................... DC 1.9A

Weight 2.9 lbs (1.3kg)

2. Battery Charger (UC 14YF2)

Fig. 2

Pilot Lamp

Cord

Battery Installation Hole

Caution Plate

Body

Nameplate

Model WH9DM WH12DM

(9.6 V) (12 V)

No-load speed 0 – 2300/min

Capacity 5/32" (4 mm) – 5/16" (8 mm)(Small screw)

3/16" (M5) – 15/32" (M12)(Ordinary bolt)

3/16" (M5) – 3/8" (M10) (High tension bolt)

Tightening

torque

Bit shank size 1/4" (6.35 mm) Hex.

Rechargeable EB9B (2.0 Ah) EB1220BL (2.0 Ah)

battery Ni-Cd battery, 9.6 V Ni-Cd battery, 12 V

Charging and discharging Charging and discharging

frequency: about 1000 frequency: about 1000

Weight 3.0 lbs (1.4 kg) 3.5 lbs (1.6 kg)

Maximum 840 in-lbs

{95 N·m 970 kgf·m}

Tightening is 15/32" (M12)

high tension bolt when fully

charged at 68°F (20°C) temp.

Tightening time: 3 sec.

Maximum 885 in-lbs

{100 N·m 1020 kgf·m}

Tightening is 15/32" (M12)

high tension bolt, when fully

charged at 68°F (20°C) temp.

Tightening time: 3 sec.

English

12

Fig. 3

Fig. 4

ASSEMBLY AND OPERATION

APPLICATIONS

䡬 Driving and removing of small screws, small bolts, etc.

REMOVAL AND INSTALLATION METHOD OF BATTERY

䡬 How to install the battery.

Align the battery with the groove in tool

handle and slip it into place.

Always insert it all the way until it locks in

place with a little click, If not, it may acciden-

tally fall out of the tool, causing injury to

you or someone around you. (Fig. 3)

䡬 How to remove the battery.

Withdraw battery from the tool handle while

pressing the latch on the side of the battery.

(Fig. 3)

CHARGING METHOD

NOTE: Before plugging into the receptacle, make sure the following points.

䡬 The power source voltage is stated on the nameplate.

䡬 The cord is not damaged.

WARNING: Do not charge at voltage higher than indicated on the nameplate.

If charged at voltage higher than indicated on the nameplate, the

charger will burn up.

1. Insert the plug of battery charger into

the receptacle.

When the plug of battery charger has been

inserted into the receptacle, pilot lamp will

blink in red. (At 1-second intervals)

WARNING:

Do not use the electrical

cord if damaged. Have

it repaired immediately.

Handle

Latch

Rechargeable

battery

Battery

Pilot lamp

Pull out

Insert

Battery

installation

hole

English

13

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown in Fig. 4. Make sure it contacts the

bottom of the battery charger.

CAUTION:

● If the batteries are inserted in the reverse direction, not only recharging will become

impossible, but it may also cause problems in the charger such as a deformed recharging

terminal.

3. Charging

When the battery is connected to the battery charger, charging will commence and the

pilot lamp will light in red. (See Table 2)

NOTE: If the pilot lamp flikers in red, pull out the plug from the receptacle and check if

the battery is properly mounted.

When the battery is fully charged, the pilot lamp will blink in red slowly. (At 1-second

intervals) (See Table 2)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown in Table 2, according to the condition

of the charger or the rechargeable battery.

(2) Regarding the temperature of the rechargeable battery.

The temperatures for rechargeable batteries are as shown in the table below, and

batteries that have become hot should be cooled for a while before being recharged.

Table 2

Indications of the pilot lamp

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for

0.1 seconds. (off for 0.1 seconds)

Lights continuously

Before

charging

While

charging

Charging

complete

Charging

impossible

Charging

impossible

Malfunction in the battery or the

charger

The battery temperature is high,

making recharging impossible.

Blinks

(RED)

Lights

(RED)

Blinks

(RED)

Flikers

(RED)

Lights

(GREEN)

Table 3 Recharging of batteries that have become hot

Temperatures at which the battery can be recharged

23°F—140°F

(–5°C—60°C)

Rechargeable batteries

EB9B, EB1220BL

English

14

(3) Regarding recharging time (At 68°F (20°C))

In approx. 60 minutes.

NOTE: The charging time may vary according to temperature and power source voltage.

4. Disconnect battery charger from the receptacle.

CAUTION:

Do not pull the plug out of the receptacle by pulling on the cord.

Make sure to grasp the plug when removing from receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the battery from the battery charger.

CAUTION:

● When the battery charger has been continuosly used, the battery charger will be heated,

thus constituting the cause of the failures. Once the charging has been completed, give

15 minutes rest until the next charging.

● If the battery is rechraged when it is warm due to battery use or exposure to sunlight,

the pilot lamp may light in green.

The battery will not be recharged. In such a case, let the battery cool before charging.

● When the pilot lamp flikers rapidly in red (at 0.2–second intervals), check for and take

out any foreign objects in the charger’s battery installation hole. If there are no foreign

objects, it is probable that the battery or charger is malfunctioning. Take it to your

authorized Service Center.

● Since the built-in micro computer takes about 3 seconds to confirm that the battery

being charged with UC14YF2 is taken out, wait for a minimum of 3 seconds before

reinserting it to continue charging. If the battery is reinserted within 3 seconds, the

battery may not be properly charged.

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been

used for an extended period is not activated, the electric discharge might be low when

using them the first and second time. This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely exhausted.

When you feel that the power of the tool becomes weaker, stop using the tool and

recharge its battery. If you continue to use the tool and exhaust the electric current, the

battery may be damaged and its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use. If such a battery is recharged

immediately after use, its internal chemical substance will deteriorate, and the battery

life will be shortened. Leave the battery and recharge it after it has cooled for a while.

English

15

BEFORE USE

Check the work area to make sure that it is clear of debris and clutter.

Clear the area of unnecessary personnel. Ensure that lighting and ventilation is adequate.

OPERATION

1. Using the convenient hook

The convenient hook can be installed on the right

or left side and the angle can be adjusted in 5 steps

between 0 and 80.

(1) Operating the hook

(a) Pull out the hook toward you in the direction of

arrow (A) and turn in the direction of arrow (B).

(Fig. 5)

(b) The angle can be adjusted in 5 steps (0°, 20°, 40°,

60°, 80°).

Adjust the angle of the hook to the desired

position for use.

(2) Switching the hook position

CAUTION:

● If the tool falls, there is a risk that malfunction and/

or physical damage can occur. It is recommended

that you also use fall-preventing wires, etc.

● Incomplete installation of the hook may result in

bodily injury when used.

(a) Securely hold the main unit and remove the

screw using a slotted head screwdriver or a

coin. (Fig. 6)

(b) Remove the hook and spring. (Fig. 7)

(c) Install the hook and spring on the other side

and securely fasten with screw. (Fig. 6)

NOTE:

Pay attention to the spring orientation. Install

the spring with larger diameter away from you.

(Fig. 8)

(3) Using the bit holder

䡬 Installing the bit

Slide the bit from the side in the direction of Fig. 9,

and then insert firmly until the groove on the pit

locks in the protruded section of the hook.

䡬 Removing the bit

Securely hold the main unit and pull out the bit by

holding the tip with your thumb. (Fig. 10)

Fig. 6

Fig. 5

Fig. 8

Fig. 7

Convenient hook

Spring

Larger diameter

faces away

English

16

CAUTION:

● The bit may come loose from the hook and cause

bodily injury when reversing the direction of the

bit as shown in Fig. 9 or when using the driver with

the bit stored incomplete.

● Only Hitachi OPTIONAL ACCESSORIES plus driver

bits (Bit No. 2; Code No. 992671, Bit No. 3; Code No.

992672) may be used. Do not use other bits since

they may come loose.

2. Installing the bit

Always follow the following procedure to install

driver bit. (Fig. 11)

(1) Pull the guide sleeve back.

(2) Insert the bit into the hexagonal hole in the anvil.

(3) Release the guide sleeve and it returns to its origianl

position.

CAUTION

If the guide sleeve does not return to its original

position, then the bit is not installed properly.

3. Removing the bit

Please do the opposite point on the method of

installing bit.

4. Confirm that the battery is mounted correctly.

5. Check the rotational direction

The bit rotates clockwise (viewed from the rear

side) by pushing the R-side of the push button.

The L-side of the push button is pushed to turn the

bit counterclockwise. (See Fig. 12). (The and

R

marks are engraved on the body.)

CAUTION

The push button can not be switched while the

impact driver is turning. To switch the push button,

stop the impact driver, then set the push button.

6. Switch operation

䡬 When the trigger switch is depressed, the tool

rotates. When the trigger is released, the tool stops.

䡬 The rotational speed can be controlled by varying the amount that the trigger switch is

pulled. Speed is low when the trigger switch is pulled slightly and increases as the trigger

switch is pulled more.

NOTE

A buzzing noise is produced when the motor is about to rotate; this is only a noise, not

a machine failure.

Fig. 10

Fig. 9

R

L

Push

button

Fig. 11

Fig. 12

Groove

Protruded section

Driver bit

Hexagonal hole

in the anvil

Movement

Guide

sleeve

English

17

7. Tightening and loosening screws

Install the bit that matches the screw, line up the bit in the grooves of the head of the

screw, then tighten it.

Push the impact driver just enough to keep the bit fitting the head of the screw.

CAUTION

䢇 Applying the impact driver for too long tightens the screw too much and can break it.

䢇 Tightening a screw with the impact driver at an angle to that screw can damage the head

of the screw and the proper force will not be transmitted to the screw.

Tighten with this impact driver lined up straight with the screw.

8. Number of screw tightenings possible

Please refer to the table below for the number of screw tightenings possible with one

charge.

<WH12DM> (EB1220BL)

<WH9DM> (EB9B)

These values may vary slightly, according to surrounding temperature and battery

characteristics.

OPERATIONAL CAUTIONS

1. Resting the unit after continuous work

After use for continuous bolt-tightening work, rest the unit for 15 minutes or so when

replacing the battery. The temperature of the motor, switch, etc., will rise if the work is

started again immediately after battery replacement, eventually resulting in burnout.

CAUTION: Do not touch the hammer case, as it gets very hot during continuous

work.

Screw used No. of tightenings

Wood screw 5/32" × 2"

Appro. 580

(Soft wood) (ø4 × 50)

Machine screw

Appro. 1230

5/16" x 5/8" (M8 × 16)

Screw used No. of tightenings

Wood screw 5/32" × 2"

Appro. 390

(Soft wood) (ø4 x 50)

Machine screw

Appro. 1030

5/16" x 5/8" (M8 x 16)

English

18

1200

1000

800

600

400

200

0

120

100

80

60

40

20

0

0 1 2 3

(868)

(694)

(521)

(347)

(174)

(1042)

1000

800

600

400

200

0

100

80

60

40

20

0

1 2 3

(868)

(694)

(521)

(347)

(174)

1000

800

600

400

200

0

100

80

60

40

20

0

1 2 3

(868)

(694)

(521)

(347)

(174)

Tightening time: sec

(Steel plate thickness

t = 3/8" (10 mm))

Tightening time: sec

(Steel plate thickness

t = 3/8" (10 mm))

Tightening torque

High strenge bolt

Ordinary bolt

kgf·cm

N·m

5/16"×1-3/6"

(in-lbs) (M8×30)

kgf·cm

N·m

3/8"×1-3/6"

(in-lbs) (M10×30)

Tightening time: sec

(Steel plate thickness

t = 3/8" (10 mm))

Fig. 13

2. Cautions on use of the speed control switch

This switch has a built-in, electronic circuit which steplessly varies the rotation speed.

Consequently, when the switch trigger is pulled only slightly (low speed rotation) and the

motor is stopped while continuously driving in screws, the components of the electronic

circuit parts may overheat and be damaged.

3. Tightening torque

Refer to Fig. 13 and 14 for the tightening torque of bolts (according to size), under the

conditions shown in Fig. 15. Please use this example as a general reference, as tightening

torque will vary according to tightening conditions.

NOTE

䡬 If a long striking time is used, screws will be strongly tightened. This may cause the screw

to break, or may damage the end of the bit.

䡬 If the unit is held at an angle to the screw being tightened, the head of the screw may be

damaged, or the specified torque may not be transmitted to the screw. Always keep the

unit and the screw being tightened in a straight line.

4. Use a tightening time suitable for the screw

The appropriate torque for a screw differs according to the material and size of the screw,

and the material being screwed etc., so please use a tightening time suitable for the

screw. In particular, if a long tightening time is used in the case of screws smaller than

5/16” (8 mm), there is a danger of the screw breaking, so please confirm the tightening

time and the tightening torque beforehand.

kgf·cm

N·m

15/32"×1-3/4"

(in-lbs) (M12×45)

English

19

Fig. 15

Bolt

Nut

Steel plate

thickness t

Explanation of strength grade:

4 — Yield point of bolt: 45,500 psi (32 kgf/mm

2

)

8 — Pulling strength of bolt: 56,900 psi (40 kgf/mm

2

)

*The following bolt is used.

Ordinary bolt: Strength grade 4.8

High tensile bolt: Hardness division 12.9

()

1200

1000

800

600

400

200

0

120

100

80

60

40

20

0

0 1 2 3

(868)

(694)

(521)

(347)

(174)

(1042)

1000

800

600

400

200

0

100

80

60

40

20

0

1 2 3

(868)

(694)

(521)

(347)

(174)

1000

800

600

400

200

0

100

80

60

40

20

0

1 2 3

(868)

(694)

(521)

(347)

(174)

Tightening time: sec

(Steel plate thickness

t = 3/8" (10 mm))

Tightening time: sec

(Steel plate thickness

t = 1" (25 mm))

Tightening time: sec

(Steel plate thickness

t = 1" (25 mm))

Tightening torque

High strenge bolt

Ordinary bolt

kgf·cm

N·m

5/16"×1-3/6"

(in-lbs) (M8×30)

kgf·cm

N·m

3/8"×1-3/6"

(in-lbs) (M10×30)

kgf·cm

N·m

15/32"×1-3/4"

(in-lbs) (M12×45)

High strenge bolt

Fig. 14

English

20

MAINTENANCE AND INSPECTION

CAUTION: Pull out battery before doing any inspection or maintenance.

1. Checking the condition of the bit.

The bits should be checked regularly. If worn or broken bits can slip or decrease the

efficiency of the motor and burn it out.

Replace worn bits with new ones.

CAUTION: If you use a driver bit of which point is worn or broken, it will be dangerous

since it slips. So replace it with a new one.

2. Check the Screws

Loose screws are dangerous. Regularly inspect them and make sure they are tight.

CAUTION: Using this power tool with loosened screws is extremely dangerous.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes (Fig. 16)

The motor employs carbon brushes which are

consumable parts. Since and excessively worn

carbon brush can result in motor trouble, replace

the carbon brush with new ones when it becomes

worn to or near the “wear limit”. In addition,

always keep carbon brushes clean and ensure that

they slide freely within the brush holders.

NOTE:

When replacing the carbon brush with a new one,

be sure to use the Hitachi Carbon Brush Code No.

999054.

5. Replacing carbon brushes

Take out the carbon brush by first removing the

brush cap and then hooking the protrusion of the

carbon brush with a flat head screw driver, etc., as

shown in Fig. 18.

When installing the carbon brush, choose the di-

rection so that the nail of the carbon brush agrees

with the contact portion outside the brush tube.

Then push it in with a finger as illustrated in Fig. 19.

Lastly, install the brush cap.

Fig. 17

Fig. 16

Fig. 18

Wear limit

Nail of carbon brush

Protrusion

of carbon

brush

0.12" (3mm)

0.45"

(11.5mm)

La page charge ...

Hitachi WH12DM Safety Instructions And Instruction Manual

Ce manuel convient également à

Hitachi WH12DM Safety Instructions And Instruction Manual

dans d''autres langues

Documents connexes