NuTone 644202 Installation Instructions Manual

64000 SERIES

INTENDED FOR DOMESTIC COOKING ONLY

INSTALLER: LEAVE THIS MANUAL TO HOMEOWNER.

HOMEOWNER: USE AND CARE INFORMATION ON PAGES 11 TO 13

Broan-NuTone LLC, 926 West State Street, Hartford, WI 53027 (1-800-637-1453)

NuTone Inc., 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687)

Broan-NuTone Canada Inc., 1140 Tristar Drive, Mississauga, ON L5T 1H9 (1-888-882-7626)

REGISTER YOUR PRODUCT ON LINE AT: www.broan.com/register

V03515 rev. J

HB0056

INSTALLATION INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

!

WARNING WARNING

- 2 -

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

1. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer at the address or telephone number

listed in the warranty.

2. Before servicing or cleaning unit, switch power

off at service panel and lock service disconnecting

means to prevent power from being switched on

accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent

warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be

done by qualified personnel in accordance with all

applicable codes and standards, including fire-rated

construction codes and standards.

4. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer’s guidelines and

safety standards such as those published by the

National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and

Air Conditioning Engineers (ASHRAE), and the local

code authorities.

5. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any additional solid-state

speed control device.

8. To reduce the risk of fire, use only steel ductwork.

9. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

a) Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that

may ignite. Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or

when cooking flaming foods.

c) Clean ventilating fans frequently. Grease should not

be allowed to accumulate on fan or filter.

d) Use proper pan size. Always use cookware appropriate

for the size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS

IN THE EVENT OF A RANGE TOP GREASE FIRE,

OBSERVE THE FOLLOWING*:

1. SMOTHER FLAMES with a close-fitting lid, cookie

sheet or metal tray, then turn off the burner. BE

CAREFUL TO PREVENT BURNS. IF THE FLAMES

DO NOT GO OUT IMMEDIATELY, EVACUATE AND

CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN – You may be

burned.

3. DO NOT USE WATER, including wet dishcloths or

towels – This could cause a violent steam explosion.

4. Use an extinguisher ONLY if:

A. You own a Class ABC extinguisher and you

know how to operate it.

B. The fire is small and contained in the area where

it started.

C. The fire department has been called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or

unbalanced impellers, keep drywall spray, construction

dust, etc. off power unit.

3. Your hood motor has a thermal overload which will

automatically shut off the motor if it becomes overheated.

The motor will restart when it will be cooled down. If

the motor continues to shut off and restart, have the

hood serviced.

4. For best capture of cooking impurities, the bottom of the

hood should be at a minimum of 20’’ (24” over a gas range)

and at a maximum of 30” above the cooking surface.

5. Two installers are recommended because of the large

size and weight of this hood.

6. To reduce the risk of fire and to properly exhaust air,

be sure to duct air outside – Do not exhaust air into

spaces within walls or ceiling or into attics, crawl

space or garage.

7. This product is equipped with a thermostat which may

start blower automatically. To reduce the risk of injury

and to prevent power from being switched on

accidentally, switch power off at service panel and

lock or tag service panel.

8. Because of the high exhausting capacity of this hood,

you should make sure enough air is entering the

house to replace exhausted air by opening a window

close to or in the kitchen.

9. To reduce the risk of fire and electric shock, the

Broan Elite 64000 Series hood must be installed with

Broan interior blower models P5 or P8; Broan exterior

blower models 331H, 332H, 335 or 336; Broan

in-line blowers models HLB3, HLB6, HLB9,

HLB11.

Other blowers cannot be substituted.

(Blowers sold separately.)

10. Use with approved cord-connection kit only.

11. Please read specification label on product for

further information and requirements.

!

HL0070

- 3 -

RMP Series Backsplash

(Stainless Steel wall

covering with warming

shelves. Optional)

Model 418

10” round

adjustable elbow

(optional)

Model 412

transition

(3

1

/4” x 10” to 7”)

Adapter and damper 3

1

/4” x 10”

(supplied with P5 and P8 blowers)

Adapter and damper 3

1

/4’’ x 14’’

(supplied with P8 blower)

Standard duct

(3

1

/4” x 10”)

Duct

(3

1

/4” x 14”)

Model P5

single-blower

(500 cfm)

64000 SERIES HOOD

- 64000 SERIES RANGE HOOD SYSTEM -

INTERIOR BLOWERS

Flow deviator

(vertical exhaust only)

(supplied with

P5 and P8 blowers)

Model 647

(7” Rd wall cap)

Model 634 or 644

(roof cap)

Model 643

(8” Rd wall cap)

8” round

standard

duct

Model 407

(7” round -

2 ft. sections)

Model 413

transition

(3

1

/4” x 10” to 8”)

Model 459 transition

(3

1

/4” x 14” to 8”)

Model P8 dual-blower (900 cfm)

for use with 36’’ hoods or wider

NOTE: The dual blower P8 can be

installed either with 3

1

/4’’ x 14’’ or

3

1

/4’’ x 10’’ ducts. For optimal air

and quiet sound performance,

use 3

1

/4’’ x 14’’ ducts.

Rough-in kit

(supplied with P5 and P8 blowers)

Model 415

7” round adjustable

elbow (optional)

- 4 -

HL0071

RMP Series Backsplash

(Stainless Steel wall

covering with warming

shelves. Optional)

64000 SERIES HOOD

- 64000 SERIES RANGE HOOD SYSTEM -

IN-LINE AND EXTERIOR BLOWERS

332KR in-line and exterior blower

rough-in kit - Purchase separately.

Model 418

10” Rd

adjustable elbow

(optional)

Model HLB3 (280 cfm)

in-line blower

(includes one 8” to 10”

round transition)

Model 331H (600 cfm)

or 332H (900 cfm)

exterior blower

Model 335 (1200 cfm)

or 336 (1500 cfm)

exterior blower

Model 441

(10” Rd wall cap)

Model 437

(High capacity roof cap)

Model 441

(10” Rd wall cap)

Model 421

(10” Rd. vert.

in-line damper)

Recommended

for use with

exterior blowers

Model 410

(10” Rd duct -

2ft. sections)

Model HLB6 (600 cfm)

in-line blower

(includes two 4½” x 18½”

to 10’’ round transitions)

Model HLB9 (800 cfm)

or HLB11 (1100 cfm)

in-line blower

(includes two 8” x 12” to

10’’ round transitions)

- 5 -

1. SELECT BLOWER OPTION AND INSTALL DUCTWORK

Either an interior or exterior blower or in-line blower may be used with this hood. The Broan Elite 64000 Series must be

installed with blower models P5, P8, HLB3, HLB6, HLB9, HLB11, 331H, 332H, 335 or 336 only. Other blowers

cannot be substituted. (Blowers sold separately).

Plan where and how the ductwork will be installed.

If installing in-line blower, refer to instructions packed with in-line blower and follow steps 1 up to 3, 6, 9, 10,

12 and up of this manual.

Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you are installing. If using 7” or 8” round

ducts, or 3

1

/4’’ x 14’’ duct, use a transition. Use 2” duct tape to seal duct joints.

The minimum hood distance above cooktop must not be less than 20’’ for an electric range and 24’’ for a gas

range. A maximum of 30” above cooktop is highly recommended for best capture of cooking impurities.

Distances over 30” are at the installer and users discretion.

Hood with

interior blower

3¼” x 10” or

3¼” x 14” duct

Roof cap

Wall

cap

HH0029A

3¼” x 14” to 8”

transition if

3¼” x 14” duct

20” minimum above

cooking surface

(24” for gas)

MODEL P5 (SINGLE) OR

P8 (DOUBLE) INTERIOR BLOWER

TYPICAL RECTANGULAR DUCTWORK

Hood

7” or 8”

round duct

Roof cap

Wall

cap

3¼” x 10” to 7”

or 8” transition

HH0015A

20” minimum above

cooking surface

(24” for gas)

MODEL P5 (SINGLE) OR

P8 (DOUBLE) INTERIOR BLOWER

7’’ OR 8’’ ROUND DUCTWORK

Hood

10” round duct

Exterior blower

HH0016A

Exterior

blower

20” minimum above

cooking surface

(24” for gas)

MODEL 331H, 332H, 335 OR 336

EXTERIOR BLOWER TYPICAL DUCTWORK

In-line blower

10” round duct

HH0060A

20” minimum

above cooking

surface

(24” for gas)

Roof cap

Wall

cap

Hood

MODEL HLB3, HLB6, HLB9 OR HLB11

IN-LINE BLOWER TYPICAL DUCTWORK

- 6 -

2. PREPARE THE INSTALLATION

Make sure that the following items are included:

- Range hood

- Accessories:

• Filters

• Bag of parts including:

(4) lock nuts, (1) wire clamp, (8) 1/2” double thread screws, (2) wire connectors,

(2) 1/2” standard screws, (6) 3/8” screws.

Parts sold separately:

- Interior blower Model P5 includes blower, rough-in kit, flow deviator and 3

1

/4” x 10” adapter

- Interior blower Model P8 includes blower, rough-in kit, flow deviator and 3

1

/4” x 10” adapter and 3

1

/4” x 14” adapter

- In-line blower assembly HLB3, HLB6, HLB9 or HLB11 (all include transition)

- In-line and exterior blower rough-in plate model 332KR, required for all In-line or Exterior Blowers

- Exterior blower assembly 331H, 332H, 335 or 336

- Halogen lights (120V, 50W, PAR 20)

- Heat lamps (120V, IR 175W, PAR 38)

- RMP Series Backsplash (optional)

- Baffle filters (optional)

- Transitions, duct, elbows, dampers, wall and roof caps. Refer to pages 3 and 4 for a complete list of venting options

and model numbers.

NOTE: For cabinets with recessed bottom, attach wood filler strips (not included) on each sides, as shown below.

Use two (2) 2-inch wide strips for 30’’ wide hoods, and four (4) 2-inch wide strips for wider hoods, cut to length.

See below for wood filler strip locations.

HD0079

A

B C

3. INSTALL BACKSPLASH (OPTIONAL)

Backsplash must be installed before the hood shell because the hood shell covers the backsplash top mounting

screws. In order to be able to install the backsplash, make sure you have at least 18’’ clearance between bottom of

hood and range control panel or cooktop. (See instructions packed with backsplash.)

HOOD LOCATIONS

WIDTHS AB C

30’’ 2’’ N/AN/A

36’’ 2’’ 4

1

/2’’ 4

1

/2’’

42’’ 2’’ 7

1

/4’’ 8

1

/4’’

48’’ 4’’ 10

1

/4’’ 11

1

/4’’

4. SELECT BLOWER OPTION (EXTERIOR OR INTERIOR)

INTERIOR BLOWER: Follow all subsequent steps of this manual.

EXTERIOR BLOWER: Refer to instructions packed with exterior blower and follow steps 6, 10, 12 and up of

the present manual.

- 7 -

Removing horizontal knockout opening on back of hood

HD0076

5. CHOOSE THE OPENING (INTERIOR BLOWER)

Remove the knockout for the chosen opening (horizontal at the back of the hood or vertical on rough-in plate).

See pictures below.

CAUTION

When using P5 blower, remove the 10’’ wide knockout (smaller part). If using P8 blower, remove

the knockout corresponding to the ducting installed (10’’ or 14’’).

Removing vertical knockout opening on rough-in plate

HD0077

10’’ KNOCKOUT

14’’ KNOCKOUT

14’’

KNOCKOUT

10’’

KNOCKOUT

6. INSTALL THE ROUGH-IN PLATE (ALL BLOWERS)

INTERIOR BLOWER: Secure the rough-in plate (provided with the P5 and P8 blower) inside the hood with four (4)

lock nuts. See picture below.

EXTERIOR OR IN-LINE BLOWER: Purchase Model 332KR separately. Refer to instructions included with the rough-in

kit. Secure the rough-in plate inside the hood with (4) lock nuts.

HD0042

Inserting deviator into hood vertical opening

7. INSTALL THE DEVIATOR (INTERIOR BLOWER)

YOU MUST install the deviator if you choose to vent the hood vertically.

Install the deviator as shown.

NOTE: If installed correctly, the deviator will protrude about 1/8” above the

rough-in plate.

HD0003

- 8 -

8. INSTALL THE ADAPTER (INTERIOR BLOWER)

Using two (2) standard 1/2’’ screws, secure the adapter to the top (or back) of the hood. Seal the adapter to the hood

using duct tape.

HD0005

HD0006

9. INSTALL THE HOOD (ALL BLOWERS)

HD0043

INTERIOR BLOWER: Run power cable to installation location. Place the hood to its location. Mark the position of the

screws (smaller part of the key holes) with a pen. Remove the hood and install the (8) 1/2” double thread screws

leaving a 1/8” gap (4 screws for 30” hood). Remove wiring cover, place the wire clamp, insert the cable in the hood and

tighten the wire clamp to secure the cable. Place the hood under the cabinet and slide it in position. Make sure the

adapter/damper assembly enters the ducting. Secure the hood by tightening the screws completely.

EXTERIOR OR IN-LINE BLOWER: Run power cable to installation location. Place the hood to its location. Mark the

position of the screws (smaller part of the key holes) with a pen. Remove the hood and install the (8) 1/2” double thread

screws leaving a 1/8” gap (4 screws for 30” hood). Remove wiring cover on top of the hood and connect wiring (see

instructions included with exterior or in-line blower). Place the hood under the cabinet and slide it in position. Secure

the hood by tightening the screws completely.

- 9 -

10. CONNECT WIRING (ALL BLOWERS)

INTERIOR BLOWER: Connect cable into wiring box using wire

connectors.

Connect wires as follow: BLACK to BLACK, WHITE to WHITE and

GREEN or BARE wire under ground screw. Reinstall wiring cover. DO

NOT FORGET TO CONNECT THE GROUND.

IN-LINE OR EXTERIOR BLOWER: Remove rough-in plate wiring cover and connect wiring (see instructions included

witn in-line or exterior blower).

WARNING

Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with

all applicable codes and standards. Before connecting wires, switch power off at service panel

and lock service disconnecting means to prevent power to be switched on accidentally.

!

1

HD0007

1) Ground screw

11. INSTALL THE BLOWER (INTERIOR BLOWER)

The blower must be installed to the rough-in plate using (4) 3/8” screws for the single blower unit and (6) 3/8” screws

for the dual blower unit. Remove the cover from the blower assembly. Remove the impeller(s) by pulling them out gen-

tly (see pictures below).

HD0021

HD0022

- 10 -

11. INSTALL THE BLOWER (INTERIOR BLOWER) (CONT’D)

Secure the blower by installing 2 more screws into the locations shown in the pictures below (single blower or dual

blower). Reinstall impeller(s) and cover.

Plug the power supply to the 3-prong male connector (A) and

the blower unit into the 2-prong female receptacle (B) inside the

hood.

HE0003

WARNING

Never plug the 2-prong blower cord to the 3-prong power supply cord.

!

FOR DUAL BLOWER UNIT, MAKE

SURE THE IMPELLERS ARE

CORRECTLY INSTALLED, THE HOOD

WILL NOT WORK PROPERLY IF

REVERSED. Both impellers are different

in the dual blower, one rotates clockwise

and the other counterclockwise. Each

wheel and motor have an arrow and a

number on them, you have to match

them correctly (see drawing beside).

Install screws into the location as shown in the pictures below (single blower or dual blower). Do not tighten screws down

fully, leave a 1/8” gap. Hang blower unit onto blower plate (screws through the large part of the keyhole). Slide the blower

to its position (screws in the small part of the keyhole). Tighten the screws.

HD0044

Single blower (P5)

Dual blower (P8)

HD0080

HD0081

Single blower (P5)

21

HD0023

FRONT

A

B

Dual blower (P8)

HD0023

1

2

- 11 -

12. LIGHT BULBS

This range hood uses 50W halogen lamps. (120V, 50W, PAR 20)

Install the lamps by rotating them clockwise into their socket holder.

13. HEAT LAMPS

The heat lamps required are 120V, 175W max, infrared bulbs. (120V, IR 175W, PAR 38)

White halogen lights can be used if warming shelves are not used. (120V, 90W, PAR 38)

Install the lamps by rotating them clockwise into their socket holder.

14. INSTALL FILTERS

It is recommended to install side filters first and finish with center one(s).

1. Insert upper end of filter into the hood (tab end).

2. Raise lower end toward the inside of hood.

3. Position lower end of filter into channel and pull on filter tab.

4. While pulling the filter tab, slide the filter top under the inner retaining piece.

Baffle filters are available as an option (see instruction sheet included with baffle filters).

HD0009

HD0010

15. USE AND CARE

Grease filters and impeller(s).

The grease filters, impeller(s) and grease rail should be cleaned frequently. Use a warm detergent solution.

Grease filters and impeller are dishwasher safe.

Remove filters by pushing filters towards the back of hood and rotating filters downward.

1

1) Tabs

- 12 -

15. USE AND CARE (CONT’D)

Hood cleaning

Stainless steel cleaning: How to maintain its « BRIGHT LOOK »

Do:

- Regularly wash surfaces with clean cloth or rag soaked with warm water and mild soap or liquid dish detergent.

- Always clean in the direction of original polish lines.

- Always rinse well with clear water (2 or 3 times) after cleaning. Wipe dry completely.

- You may also use a specialized household stainless steel cleaner.

Don’t:

- Do not use any steel or stainless steel wool or any other scrapers to remove stubborn dirt.

- Do not use any harsh or abrasive cleansers.

- Do not allow dirt to accumulate.

- Do not let plaster dust or any other construction residues reach the hood. During construction or renovation, cover

the hood to make sure no dust sticks to stainless steel surface.

Avoid: when choosing a detergent

- Any cleaners that contain bleach will attack stainless steel.

- Any products containing : chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.

- Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive

and should never be used close to a range.

Enamel finish:

Clean with warm water and mild detergent only. When discoloration occurs, use a good enamel polish such as auto-

motive polish. (DO NOT use rough abrasive cleaner or porcelain cleaner.)

16. OPERATION

Always turn your hood on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few

minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and brighter.

1

2

3

4

1) Warming lamp switches

2) Halogen light switches

3) ON/OFF blower switch

4) Blower speed control

HC0028

BLOWER

The blower is operated using two (2) controls.

Use the red, lighted on/off switch to start and stop the blower. When turned on, the blower will operate at the previous

setting of the speed control.

Turn the speed control knob clockwise to decrease blower speed – counterclockwise to increase speed.

COOKTOP LIGHTING (HALOGEN)

A double set of ON/OFF switches controls the halogen lights.

The front rocker controls the center light (for 42” and 48” hoods). The rear rocker controls both side lights (each switch

controls one light for 30” and 36” hood). Select one, two or three lights for best cooking lighting.

Use PAR 20, 50W halogen bulbs.

- 13 -

WARMING LAMPS (INFRARED)

Each warming lamp is controlled with its own ON/OFF switch.

Use infrared light bulbs (120V, IR175W, PAR38) or white halogen bulbs (120V, 90W, PAR38) if food warming shelves are

not used.

HEAT SENTRY

This hood is equipped with a Heat Sentry thermostat. This thermostat is a device that will turn on or speed up the blower

if it senses excessive heat above the cooking surface.

1) If blower is OFF - it turns blower ON to HIGH speed.

2) If blower is ON at a lower speed setting – it turns the blower up to HIGH speed.

When the temperature level drops to normal, the blower will return to its original setting.

WARNING

Never place highly flammable material under warming lamps.

WARNING

The HEAT SENTRY can start the blower even if the hood is turned OFF. In this case, it is impossible

to turn the blower OFF with blower switch. If you must stop the blower, do it from the main

electrical panel.

!

16. OPERATION (CONT’D)

WARRANTY

BROAN-NUTONE LLC ONE-YEAR LIMITED WARRANTY

Broan-NuTone LLC warrants to the original consumer purchaser of its products that such products will be free

from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE

NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED

WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

During this one-year period, Broan-NuTone LLC will, at its option, repair or replace, without charge, any product

or part which is found to be defective under normal use and service.

This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been

subject to misuse, negligence, accident, improper maintenance or repair (other than by Broan-NuTone LLC),

faulty installation or installation contrary to recommended installation instructions.

The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some

states or provinces do not allow limitation on how long an implied warranty lasts, so the above limitation may not

apply to you.

BROAN-NUTONE LLC’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE LLC’S OPTION,

SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.

BROAN-NUTONE LLC SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL

DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some

states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so

the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state

or province to another. This warranty supersedes all prior warranties.

To qualify for warranty service, you must (a) notify Broan-NuTone LLC at one of the addresses or telephone

number stated below, (b) give the model number and part identification and (c) describe the nature of any defect

in the product or part. At the time of requesting warranty service, you must present evidence of the original

purchase date.

Broan-NuTone LLC, 926 West State Street, Hartford, WI 53027 (1-800-637-1453)

NuTone Inc., 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687)

Broan-NuTone Canada Inc., 1140 Tristar Drive, Mississauga, ON L5T 1H9 (1-888-882-7626)

KEY QTY (hood width)

NO.

PART NUMBER DESCRIPTION

30” 36” 42” 48”

- 14 -

28 910112

8

17

5

6

14

12

13

7

15

16

4

3

20

19

17

2

17

18

1

HL0002

SERVICE PARTS

64000 Series

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

V06750

V02264

V02773

V02772

V03435

V03436

V03501

V03507

V03502

V03503

V03504

V03505

V03517

V03518

V03519

V03520

V00673

V02512

V01869

V01582

V00606

V03509

V03510

V13216

V13217

V13218

V13219

V03686

V02544

V03598

V03515

V13278

BROAN ELITE LOGO

SOCKET LAMP

MALE CONNECTOR

FEMALE CONNECTOR

THERMOSTAT

THERMOSTAT BRACKET

SPEED CONTROLLER

SPST SINGLE SWITCH FOR WARMING LAMP

SPST DOUBLE SWITCH FOR HALOGEN LIGHT

SPST LIGHTED SINGLE SWITCH FOR BLOWER

SPEED CONTROL BUTTON

TERMINAL STRIP

10" POWER CORDS

10" CORDS FOR HEAT LAMP

10" CONTROL WIRE

10" LIGHTED SWITCH WIRE

LOCK NUT NO. 8-32

SCREW NO. 8-32 x 1/2" QUADREX

MACHINE SCREW NO. 6-32 x 1/4"

LOCK NUT NO. 6-32

SCREW NO. 8-3/8"T/B NO. 8 HEAD

RANGEMASTER FILTER 8.930

”

x 9.800

”

RANGEMASTER FILTER 11.930

”

x 9.800

”

GREASE RAIL 30"

GREASE RAIL 36"

GREASE RAIL 42"

GREASE RAIL 48"

FILTER CLIP

HALOGEN LAMP PAR 20 50 W

HEAT LAMP

INSTALLATION GUIDE

PARTS BAG ((4) lock nut no.10-32, (1) wire clamp LP16-AP, (2) wire connectors no.74B,

(8) double thread screw 6-12 x 0.5, (6) no. 8 x 3/8” screws, (2) no. 6 x 1/2" screws)

1

4

1

2

1

2

1

2

1

7

2

1

-

3

2

1

4

1

2

1

2

1

2

1

7

-

3

-

1

-

3

2

1

5

1

2

1

2

1

2

1

8

2

-

1

-

4

3

2

1

5

1

2

1

2

1

2

1

8

-

4

-

1

4

3

2

1

KEY

NO.

PART NUMBER DESCRIPTION QTY

- 15 -

SERVICE PARTS

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

V13296

V03500

V12997

V03577

V02160

V01869

V01857

V01582

V14973

V01810

V03400

V01766

V00871

V02001

V01831

V11705

V11614

V01927

V03495

V03494

V13230

V03496

V00660

V05520

V00613

1

4

1

3

2

1

4

1

2

ADAPTER AND DAMPER 3

1

/4’’ x 10’’

AIR DEFLECTOR

SINGLE BLOWER ROUGH-IN PLATE ASSEMBLY

FOAM 1/2” x 1/2” x 12”

CAPACITOR 15MFD

MACHINE SCREW NO. 6-32 x 1/4”

WIRE COVER

LOCK NUT NO. 6-32

SINGLE BLOWER ASSEMBLY

IMPELLER RING

BLOWER IMPELLER 7.094” x 3.375” CW

MOTOR 165W CW

WASHER 3/16” ID x 3/4’’ OD

MOTOR GROMMET G-431-1

8” TIE WRAP

MOTOR MOUNT

WIRE NO. 18 TEW BROWN x 10”

METRIC SCREW M4 x 6MM PAN QDRX

STRAIN RELIEF FOR BLOWER POWER CORD

36” BLOWER POWER CORD

OUTLET BOX COVER

POWER CORD, 120 VOLTS

STRAIN RELIEF FOR POWER CORD

SCREW NO. 8 x 3/8”, T/B, NO. 8 HEAD

SCREW NO. 10-32 x 3/8, TF, GREEN

SINGLE BLOWER/ROUGH-IN

(Model P5)

HL0021

19

21

18

17

20

22

2

3

23

4

1

9

6

8

5

15

14

13

6

16

12

7

11

10

21

22

23

2

3

20

24

25

1

19

18

17

16

15

13

6

9

10

11

12

14

4

5

KEY

NO.

PART NUMBER DESCRIPTION QTY

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

V14971

V13296

V03500

V14975

V03577

V01582

V02160

V01857

V01766

V03400

V14974

V01810

V03399

V03457

V00871

V01831

V11705

V11614

V02001

V01927

V03495

V03494

V14960

V00660

V03496

V05520

V00613

1

2

1

2

1

6

4

2

6

8

1

4

2

ADAPTER AND DAMPER 3

1

/4” x 14’’

ADAPTER AND DAMPER 3

1

/4” x 10’’

AIR DEFLECTOR

DUAL BLOWER ROUGH-IN PLATE ASSEMBLY

FOAM 1/2” x 1/2” x 12”

LOCK NUT NO. 6-32

CAPACITOR 15MFD

WIRE COVER

MOTOR 165W CW

BLOWER IMPELLER, HOOD 7.094” x 3.375” CW

DUAL BLOWER ASSEMBLY

IMPELLER RING

BLOWER IMPELLER, HOOD 7.094” x 3.375” CCW

MOTOR 165W CCW

WASHER 3/16” ID x 3/4 OD

8” TIE WRAP

MOTOR MOUNT

WIRE NO.18 TEW BROWN x 10”

MOTOR GROMMET G-431-1

METRIC SCREW M4 x 6MM PAN QDRX

STRAIN RELIEF FOR BLOWER POWER CORD

36” BLOWER POWER CORD

OUTLET BOX COVER

STRAIN RELIEF FOR POWER CORD

POWER CORD, 120 VOLTS

SCREW NO. 8 x 3/8”, T/B, NO. 8 HEAD

SCREW NO. 10-32 x 3/8”, TF, GREEN

- 16 -

SERVICE PARTS

DUAL BLOWER/ROUGH-IN

(Model P8)

7

8

GUIDE D’INSTALLATION

SÉRIE 64000

CONÇUE UNIQUEMENT POUR LA CUISSON DOMESTIQUE

INSTALLATEUR : LAISSER CE MANUEL AU PROPRIÉTAIRE

PROPRIÉTAIRE : INSTRUCTIONS D’UTILISATION ET D’ENTRETIEN EN PAGES 27 À 29

Broan-NuTone LLC, 926 West State Street, Hartford, WI 53027 (1-800-637-1453)

NuTone Inc., 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687)

Broan-NuTone Canada Inc., 1140 Tristar Drive, Mississauga, ON L5T 1H9 (1-888-882-7626)

ENREGISTREZ VOTRE PRODUIT EN LIGNE À : www.broan.com/register

V03515 rév.J

HB0056

LIRE ET CONSERVER CES INSTRUCTIONS

!

- 18 -

AVERTISSEMENT AVERTISSEMENT

AFIN DE RÉDUIRE LES RISQUES D’INCENDIE,

D’ÉLECTROCUTION OU DE BLESSURES CORPORELLES,

SUIVEZ LES INSTRUCTIONS SUIVANTES :

1. N’utilisez cet appareil que de la façon prévue par

le manufacturier. Si vous avez des questions,

contactez le manufacturier à l’adresse et au

numéro de téléphone indiqués sur la garantie.

2. Avant de réparer ou de nettoyer l’appareil, coupez

l’alimentation électrique en verrouillant le panneau de

service afin d’éviter sa remise en marche accidentelle.

Si le panneau de service ne peut être verrouillé, y

fixer un avertissement en évidence.

3. Les travaux d’installation et de raccordement

électrique doivent être effectués par une personne

qualifiée, conformément aux codes et standards

de construction, incluant ceux concernant le feu.

4. Une quantité d’air adéquate est requise afin d’assurer

une bonne combustion et l’évacuation des gaz par

la cheminée dans le cas des équipements alimentés

au gaz, afin de prévenir les retours de cheminée.

Conformez-vous aux instructions et aux standards

de sécurité des manufacturiers d’équipement de

chauffage, tel que publiés par la

National Fire

Protection Association

(NFPA), et l’

American

Society for Heating, Refrigeration and Air

Conditioning Engineers

(ASHRAE), ainsi que les

responsables des codes locaux.

5. Lorsque vous coupez ou perforez un mur ou un

plafond, prenez garde de ne pas endommager

les fils électriques ou tout appareil cachés.

6. Les ventilateurs avec conduits doivent toujours

évacuer l’air à l’extérieur.

7. Ne pas utiliser cet appareil avec une commande

de vitesse à semiconducteur additionnelle.

8. Afin de réduire les risques d’incendie, n’utilisez

que des conduits de métal.

9. Cet appareil doit être mis à la terre.

AFIN DE RÉDUIRE LES RISQUES DE FEU

DE CUISINIÈRE :

a) Ne jamais laisser les appareils de cuisson sans

surveillance lorsqu’ils sont réglés à feu vif. Les

débordements engendrent de la fumée et des

déversements graisseux pouvant s’enflammer.

Chauffez l’huile lentement, à feu doux ou moyen.

b) Toujours mettre la hotte en marche lorsque vous

cuisinez à feu vif ou que vous cuisinez des

mets flambés.

c) Nettoyez régulièrement la (les) roue(s) du ventilateur.

Ne laissez pas la graisse s’accumuler sur le

ventilateur ou les filtres.

d) Utilisez le bon format de casserole. Servez-vous

toujours de casseroles et d’ustensiles appropriés à

la dimension de la surface chauffante.

AFIN D’ÉVITER TOUT RISQUE DE BLESSURES

DANS LE CAS D’UN FEU DE CUISINIÈRE, SUIVEZ

CES DIRECTIVES* :

1. Étouffez les flammes avec un couvercle hermétique,

une tôle à biscuits ou un plateau métallique et

ensuite, éteindre le brûleur. PRENEZ SOIN

D’ÉVITER LES BRÛLURES. SI LES FLAMMES

NE S’ÉTEIGNENT PAS IMMÉDIATEMENT,

ÉVACUEZ LES LIEUX ET APPELEZ LES POMPIERS.

2. NE PRENEZ JAMAIS UNE CASSEROLE EN

FLAMMES DANS VOS MAINS – Vous pourriez

subir des brûlures.

3. N’UTILISEZ PAS D’EAU, incluant linge à vaisselle

ou serviette mouillés – ceci pourrait occasionner

une violente explosion.

4. N’utilisez un extincteur QUE DANS LE CAS OÙ:

A. Vous savez qu’il s’agit d’un extincteur de classe ABC

et que vous en connaissez le fonctionnement.

B. L’incendie est petit et limité à l’endroit où il a débuté.

C. Les pompiers ont été avisés.

D. Vous pouvez combattre l’incendie en ayant

accès à une sortie de secours.

*Tirées du

Kitchen Fire Safety Tips

publié par la NFPA.

ATTENTION

1. Pour usage domestique seulement. Ne pas utiliser pour

évacuer des vapeurs ou des produits dangereux

ou explosifs.

2. Afin d’éviter tout dommage au moteur et de débalancer

ou de rendre bruyante la roue du moteur, garder

votre appareil à l’abri des poussières de placoplâtre

et de construction/rénovation, etc.

3. Le moteur de votre hotte possède une protection

thermique qui éteindra automatiquement le moteur s’il

devient surchauffé. Le moteur repartira automatiquement

une fois refroidi. Si le moteur continue à arrêter et

à repartir, faites-le vérifier.

4. Pour une meilleure évacuation des odeurs de cuisine,le

bas de votre hotte devrait être situé à un minimum

de 20 po (24 po d’une cuisinière à gaz) et un maximum

de 30 po au-dessus de la table de cuisson.

5. Deux installateurs sont recommandés lors de l’installation

vu la grande dimension et le poids de cette hotte.

6. Afin de réduire les risques d’incendie, assurez-vous

d’évacuer l’air à l’extérieur – Ne pas évacuer l’air dans

des espaces restreints comme l’intérieur des murs ou

plafond ou dans le grenier, faux plafond ou garage.

7. Cet appareil est équipé d’un thermostat pouvant

faire démarrer le ventilateur automatiquement. Afin

de réduire le risque de blessure, couper le courant

à partir du panneau électrique et verrouiller ou

apposer un avertissement sur le panneau afin de

prévenir que la hotte soit mise en marche automatiquement.

8. À cause de la grande capacité d’évacuation de

cette hotte, il est recommandé d’ouvrir une fenêtre dans

ou près de la cuisine afin de remplacer l’air évacué.

9. Afin de réduire les risques d’incendie et d’électrocution,

la hotte Broan Elite série 64000 doit être installée

uniquement avec un des ventilateurs intérieurs Broan

suivants : P5 ou P8; un des ventilateurs extérieurs

Broan suivants : 331H, 332H, 335 ou 336 ou un des

ventilateurs en ligne Broan suivants : HLB3, HLB6,

HLB9 ou HLB11 (vendus séparément). Aucun

autre ventilateur ne doit être utilisé.

10. Cette hotte ne doit être utilisée qu’avec un ensemble

de cordon d’alimentation approuvé.

11. Veuillez consulter l’autocollant apposé à l’intérieur de

la hotte pour plus d’information ou autres exigences.

!

- 19 -

HL0070

Dosseret Série RMP

(Recouvrement de mur

en acier inoxydable

avec support assiettes)

Adaptateur et volet 3

1

/4 po x 10 po

(fourni avec ventilateurs P5 et P8)

Adaptateur et volet 3

1

/4 po x 14 po

(fourni avec ventilateur P8)

Modèle P5 ventilateur

simple (500 pcm)

Modèle P8 ventilateur double

(900 pcm) pour hottes de

36 po ou plus

NOTE : Le ventilateur double P8 peut être

installé autant avec des conduits

de 3

1

/4 po x 14 po que des conduits

de 3

1

/4 po x 10 po. Pour une

performance optimale au niveau

sonore et de la ventilation, utiliser

des conduits de 3

1

/4 po x 14 po.

Plaque ventilateur fournie

avec ventilateurs P5 et P8

HOTTE SÉRIE 64000

- SYSTÈME DE HOTTE DE CUISINIÈRE SÉRIE 64000 -

VENTILATEURS INTÉRIEURS

Modèle 407

(Conduit de

7 po rond

section

de 2 pi)

Modèle 412

transition

(3

1

/4 po x 10 po à 7 po)

Conduit

standard

3

1

/4 po x 10 po

Conduit

3

1

/4 po x 14 po

Modèle 643

(Capuchon de

mur 8 po rond)

Déviateur d’air (sortie verticale seulement)

(fourni avec les ventilateurs P5 et P8)

Modèle 647

(Capuchon de

mur 7

po rond)

Modèle 634 ou 644

(Capuchon de toit)

Conduit

standard de

8 po rond

Modèle 413 transition

(3

1

/4 po x 10 po à 8 po)

Modèle 459

transition

3

1

/4 po x 14 po à 8 po)

Modèle 415

coude ajustable

7 po rond (optionel)

Coude ajustable

8 po rond (optionel)

- 20 -

HL0071

HOTTE SÉRIE 64000

- SYSTÈME DE HOTTE DE CUISINIÈRE SÉRIE 64000 -

VENTILATEURS EN LIGNE ET EXTÉRIEURS

Dosseret Série RMP

(Recouvrement de mur

en acier inoxydable

avec support assiettes)

Modèle 421

(Volet intérieur

10 po rond vert.)

Recommandé

pour utilisation

avec ventilateurs

extérieurs

Modèle 410

(Conduit de 10 po rond

standard section de 2 pi)

Modèle 418

Coude ajustable de

10 po (optionnel)

Ventilateur en ligne

modèle HLB3 (280 pcm)

(incluant une transition

ronde 8 po à 10 po)

Ventilateur extérieur

modèle 331H (600 pcm)

ou 332H (900 pcm)

Ventilateur extérieur

modèle 335 (1200 pcm)

ou 336 (1500 pcm)

Modèle 441

(Capuchon de

mur 10 po rond)

Modèle 437

(Capuchon de toit haut rendement)

Modèle 441

(Capuchon de

mur 10 po rond)

Plaque ventilateur 332KR pour

ventilateurs extérieurs ou en

ligne. Vendue séparément.

Ventilateur en ligne modèle

HLB6 (600 pcm)

(incluant deux transitions

rondes de 4½ po x 18½ po

à 10 po)

Ventilateur en ligne

modèle HLB9 (800 pcm)

ou HLB11 (1100 pcm)

(incluant deux transitions

rondes de 8 po x 12 po

à 10 po)

La page est en cours de chargement...

NuTone 644202 Installation Instructions Manual

Ce manuel convient également à

NuTone 644202 Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents