RS PRO IM-502 Manuel utilisateur

Catégorie
Mesure
Taper
Manuel utilisateur
Instruction Manual
IM-502
Desktop Indoor Air Quality (IAQ) Monitor
IAQ Monitor/ English
2016-10-17 V001 EN-1
Contents
Introduction EN-2
Features EN-2
General specification EN-2
Instrument description EN-4
Safety EN-4
Operation EN-5
Software installation EN-10
Limited Warranty EN-12
Contact information EN-13
IAQ Monitor/ English
EN-2 2016-10-17 V001
Introduction:
IM-502 is a desktop indoor air quality monitor that can
measure carbon dioxide, relative humidity, air temperature,
and ventilation rate.
Features:
Non-Dispersive Infrared (NDIR) CO2 sensor ensures long
term stability and durability.
4 Measurements in one monitor, CO2, CO2 Ventilation
Rate, Temperature and Humidity.
Large display.
Easy-to-use PC software for parameter settings and
analysis.
Fast USB download.
Internal memory stores up to 17,000 data.
Selectable record time Interval.
CO2/Temperature/Humidity high, low alarm setting.
Set on the table or wall-mounted (with1/4” tripod nut).
Maximum/Minimum values.
General specification:
Display:
Triple LCD display
Sensor:
NDIR, Thermistor and Capacitive
Power Supply:
AC100 ~240V, 12V/1A switching
power adaptor, plug dimension
5.5*2.1*1.0mm.
Dimension:
89mm x62mm x128mm. (LxWXH).
Weight:
Approx. 190g
IAQ Monitor/ English
2016-10-17 V001 EN-3
Accessories:
Manual, power adaptor and 5-pin
USB cable.
Measuring range and accuracy:
Carbon dioxide:
Sensor Type:
Non-Dispersive InfraRed (NDIR)
Measurement Range:
0 to 9999ppm
Accuracy:
±5% read value or
±75ppm(0-2000ppm)
Resolution;
±1ppm
Response Time:
Reaches 90% in approximately 2
minutes
Temperature:
Sensor Type:
Thermistor
Measurement Range:
C~50°C / 32°F~122°F
Accuracy:
±1.0°C/±1.8°F
Resolution:
0.1°C/0.1°F
Response Time:
Approximately 1 second
Relative Humidity:
Sensor Type:
Measurement Range:
Accuracy;
Resolution:
Response Time:
IAQ Monitor/ English
EN-4 2016-10-17 V001
Instrument description:
1. LCD Monitor
2. Mode/Left button
3. Datalogger button
4. Enter button
5. Right button
6. CO2 concentration
indicator; good
7. CO2 concentration
indicator; normal
8. CO2 concentration
indicator; poor
9. Setting reset button
10. USB jack
11. External power input jack
Safety:
CAUTION
Be extremely careful for the following
conditions while measuring.
Do not operate the meter in the environment with
explosive gas (material), combustible gas (material)
steam or filled with dust.
IAQ Monitor/ English
2016-10-17 V001 EN-5
Do not operate in environments with flammable gas or
humid environments.
Operation Altitude: Up to 2000M.
Operating Environment is for indoors use only. The meter
was designed for being used in an environment of
pollution degree 2.
Clean with soft dry cloth. Do not clean with chemical and
other solvents.
Operating power consumption: 2.4W.
Operating Temperature & Humidity: 0°C ~ +50°C, <95%
RH(non-condensing)
Storage Temperature & Humidity : -10°C ~ 60°C, 0%~
70%RH.
Operation:
1. Connect the power supply to the meter, the meter starts
the measurements and updates the readings.
2. LCD displays current CO2, Humidity and Temperature,
date and time.
Mode
Press repeatedly to view the following screens in
this order:
IAQ Monitor/ English
EN-6 2016-10-17 V001
L/P/S ventilationCFM/P ventilation minimum
valuemaximum valuesave effective percentage
.
REC
Press and hold until “Rec” appears on the display
to enter the automatic recording function. The currently
measured value, setting function and USB connection are
shown during the recording process.
Press and hold again until “Recis disappears
from the display to exit this function.
RESET
Disconnect the power, press and hold the “RESET” button
and then connect the power to restore all settings to the
factory default values.
Function Setting
Press and hold and together for 2 seconds to
enter the function setting mode.
Press or to select the setting modes.
There are 7 settings:
1. 12/24 hour mode.
2. Clock setting.
3. Alarm ON/OFF.
4. CO2 alarm high value.
5. CO2 alarm low value.
6. Outdoor CO2.
7. ABC Auto-correct function.
IAQ Monitor/ English
2016-10-17 V001 EN-7
1. 12/24 hour mode:
Press to enter the hour mode.
Press or to select 12 or
24.
Press to save and exit this
setting.
Press to go to the next setting or
press and hold and together for 2 seconds
to exit the function setting.
2. Clock setting.
Press to enter the clock setting.
The hour digit is flashing, press
repeatedly to select the desired digit
from hour, minute, month, date and
year.
Press or to decrease or increase the value.
Press to save and exit this setting.
Press to go to the next setting or
press and hold and together for 2 seconds
to exit the function setting.
3. Alarm ON/OFF
Press to enter the alarm ON/OFF.
Press or to select ON or
OFF.
Press to save and exit this setting.
IAQ Monitor/ English
EN-8 2016-10-17 V001
Press to go to the next setting or
press and hold and together for 2 seconds
to exit the function setting.
4. CO2 alarm high value
Press to enter the CO2 alarm high
value setting, the first digit is flashing.
Press repeatedly to select the
desired digit.
Press or to decrease or
increase the value.
Press to save and exit this setting.
Press to go to the next setting or
press and hold and together for 2 seconds
to exit the function setting.
5. CO2 alarm low value:
Press to enter the CO2 alarm low
value setting, the first digit is flashing.
Press repeatedly to select the
desired digit.
Press or to decrease or
increase the value.
Press to save and exit this setting.
Press to go to the next setting or
press and hold and together for 2 seconds
to exit the function setting.
IAQ Monitor/ English
2016-10-17 V001 EN-9
6. Outdoor CO2:
Press to enter the outdoor CO2
setting, the first digit is flashing.
Press repeatedly to select the
desired digit.
Press or to decrease or
increase the value.
Press to save and exit this setting.
Press to go to the next setting or
press and hold and together for 2 seconds to
exit the function setting.
7. ABC Auto-correct function:
Press to enter the ABC
auto-correct function.
Press or to select ON or
OFF.
Press to save and exit this setting.
Press to go to the next setting 12/24 hour mode
or press and hold and together for 2
seconds to exit the function setting.
Once the ABC function is turned on, it uses 400ppm as
the standard and will have adjusted approximately
30ppm over an accumulated time of 180 hours; therefore,
it is recommended to place it at a well-ventilated place
once the function is enabled.
IAQ Monitor/ English
EN-10 2016-10-17 V001
Ventilation Formula
CFM/P(inch/minute/person)
CFM/P = 10600/(Cs-Co)
Cs = CO2 read value, Co = CO2 outdoor read value.
L/P/S(liter/second/person)
L/P/S=(CFM/P)*28.32/60
Software Installation
The package contains: CD and USB cable
Systems requirement : XP/ Windosw7/ Windows 8.1/
Windows10
1. Insert the CD into the PC to install the desktop program:
IAQ Monitor/ English
2016-10-17 V001 EN-11
2. Remove the CD from the PC after the installation is
completed
3. Connect the meter to the PC using the USB cable
included.
4. Execute the PC desktop software program by
double-clicking the left mouse button on the desktop
program (Indoor Air Quality Data Logger.exe) to
execute the desktop program.
IAQ Monitor/ English
EN-12 2016-10-17 V001
Limited Warranty:
This meter is warranted to the original purchaser against
defects in material and workmanship for 3 years from the
date of purchase. During this warranty period, RS
Components will, at its option, replace or repair the
defective unit, subject to verification of the defect or
malfunction. This warranty does not cover fuses,
disposable batteries, or damage from abuse, neglect,
accident, unauthorized repair, alteration, contamination, or
abnormal conditions of operation or handling.
Any implied warranties arising out of the sale of this product,
including but not limited to implied warranties of
merchantability and fitness for a particular purpose, are
limited to the above. RS Components shall not be liable for
loss of use of the instrument or other incidental or
consequential damages, expenses, or economic loss, or for
any claim or claims for such damage, expense or economic
loss. Some states or countries laws vary, so the above
limitations or exclusions may not apply to you. For full terms
and conditions, refer to the RS website.
IAQ Monitor/ English
2016-10-17 V001 EN-13
Contact information:
Africa
RS Components SA
P.O. Box 12182,
Vorna Valley, 1686
20 Indianapolis Street,
Kyalami Business Park,
Kyalami, Midrand
South Africa
www.rs-components.com
Asia
RS Components Pte
Ltd.
31 Tech Park Crescent
Singapore 638040
www.rs-components.com
China
RS Components Ltd.
Suite 23 A-C
East Sea Business
Centre
Phase 2
No. 618 Yan'an Eastern
Road
Shanghai, 200001
China
www.rs-components.com
Europe
RS Components Ltd.
PO Box 99, Corby,
Northants.
NN17 9RS
United Kingdom
www.rs-components.com
Japan
RS Components Ltd.
West Tower (12th Floor),
Yokohama Business
Park,
134 Godocho, Hodogaya,
Yokohama, Kanagawa
240-0005
Japan
www.rs-components.com
U.S.A
Allied Electronics
7151 Jack Newell Blvd. S.
Fort Worth,
Texas 76118
U.S.A.
www.alliedelec.com
South America
RS Componentes
Limitada
Av. Pdte. Eduardo Frei M.
6001-71
Centro Empresas El
Cortijo
Conchali, Santiago, Chile
www.rs-components.com
Manuel d'utilisation
IM-502
Moniteur de qualité de l'air intérieur (QAI)
de bureau
FR
Moniteur QAI / Français
2016-10-17 V001 FR-1
Table des matières
Introduction FR-2
Caractéristiques FR-2
Spécifications générales FR-2
Description de l'instrument FR-4
Sécurité FR-4
Fonctionnement FR-5
Installation du logiciel FR-10
Garantie limitée FR-12
Coordonnées FR-13
Moniteur QAI / Français
FR-2 2016-10-17 V001
Introduction :
L'IM-502 est un moniteur de bureau de la qualité de l'air
intérieur pouvant mesurer le dioxyde de carbone, l'humidité
relative, la température de l'air et le débit de ventilation.
Caractéristiques :
Le capteur de CO2 InfraRouge Non-Dispersif (NDIR)
assure une stabilité et une durabilité à long terme.
4 mesures dans un seul moniteur, CO2, Débit de
ventilation CO2, Température et Humidité.
Grand écran.
Logiciel PC facile à utiliser pour réglages des paratres
et analyse.
chargement USB rapide.
La mémoire interne stocke jusqu'à 17.000 données.
Intervalle de temps d'enregistrement sélectionnable.
glage d'alarme haute, basse
CO2/Température/Humidité.
Positionné sur table ou à montage mural (avec écrou de
trépied 1/4”).
Valeurs Maximum/Minimum.
Spécifications gérales :
Écran :
Triple écran LCD
Capteur :
NDIR, Thermistance et Capacitif
Alimentation
électrique :
CA 100 ~ 240 V, adaptateur secteur
à commutation 12 V/1 A,
dimensions de la fiche 5,5 * 2,1 *
1,0 mm.
Dimensions :
89 mm x 62 mm x 128 mm. (L x l x H).
Poids :
Environ 190 g
Moniteur QAI / Français
2016-10-17 V001 FR-3
Accessoires :
Manuel, adaptateur secteur et câble
USB 5 broches.
Plage et précision de mesure :
Dioxyde de carbone :
Type de capteur :
InfraRouge Non-Dispersif (NDIR)
Plage de mesure :
0 à 9999 ppm
Précision :
±5 % valeur lue ou ±75 ppm
(0-2000 ppm)
solution :
±1 ppm
Temps de réponse :
Atteint 90 % en environ 2 minutes
Température :
Type de capteur :
Thermistance
Plage de mesure :
0 °C ~ 50 °C / 32 °F ~ 122 °F
Précision :
±1,0 °C/±1,8 °F
solution :
0,1 °C/0,1 °F
Temps de réponse :
Environ 1 seconde
Humidité relative :
Type de capteur :
Plage de mesure :
Précision :
solution :
Temps de réponse :
Moniteur QAI / Français
FR-4 2016-10-17 V001
Description de l'instrument :
1. Moniteur LCD
2. Bouton Mode/Gauche
3. Bouton Enregistreur de
données
4. Bouton Entrée
5. Bouton Droite
6. Indicateur de
concentration de CO2 ;
bon
7. Indicateur de concentration
de CO2 ; normal
8. Indicateur de concentration
de CO2 ; mauvais
9. Bouton de réinitialisation
des paramètres
10. Prise USB
11. Prise d'alimentation
électrique externe
curité :
ATTENTION
Soyez extrêmement attentif aux
conditions suivantes lors des mesures.
N'utilisez pas le compteur dans un environnement avec
du gaz (matière) explosif, du gaz (matière) combustible,
de la vapeur ou rempli de poussière.
Moniteur QAI / Français
2016-10-17 V001 FR-5
Ne l'utilisez pas dans des environnements avec des gaz
inflammables ou des environnements humides.
Altitude de fonctionnement : Jusqu'à 2000 M.
L'environnement de fonctionnement est pour une utilisation à
l'intérieur uniquement. Le compteur a été conçu pour être
utilisé dans un environnement de pollution de degré 2.
Nettoyez-le avec un chiffon doux et sec. Ne le nettoyez pas
avec des produits chimiques et d'autres solvants.
Consommation électrique en fonctionnement : 2,4 W.
Température et humidité de fonctionnement : 0°C ~
+50°C, < 95% HR (sans condensation)
Température et humidité de stockage : -10°C à 60°C, 0 % à
70 % HR.
Fonctionnement :
1. Branchez l'alimentation électrique au compteur, le compteur
commence les mesures et met à jour les lectures.
2. L'écran LCD affiche CO2, Humidi, Température, date et
heure en cours.
Mode
Appuyez plusieurs fois sur pour visualiser les écrans
suivants dans cet ordre :
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70

RS PRO IM-502 Manuel utilisateur

Catégorie
Mesure
Taper
Manuel utilisateur