Hitachi DH 30PC2 Manuel utilisateur

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE

AVERTISSEMENT

Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité

de ce produit. Prière de lire et de comprendre ce mode d’emploi avant d’utiliser

l’outil motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs

avant qu’ils utilisent l’outil motorisé.

INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS

WARNING

Improper and unsafe use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read

and understand this manual before operating the power tool. Please keep this

manual available for others before they use the power tool.

MANUAL DE INSTRUCCIONES E INSTRUCCIONES DE SEGURIDAD

ADVERTENCIA

¡La utilización inapropiada e insegura de esta herramienta eléctrica puede

resultar en lesiones serias o en la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y comprenda este manual antes de utilizar la herramienta eléctrica. Guarde

este manual para que puedan leerlo otras personas antes de que utilicen la

herramienta eléctrica.

Model Rotary Hammer

Modèle Marteau rotatif

Modelo Martillo perforador

DH 30PC2

CONTENTS

English

Page

IMPORTANT SAFETY INFORMATION

..... 3

MEANINGS OF SIGNAL WORDS ...... 3

SAFETY ................................................... 4

GENERAL SAFETY RULES ................. 4

SPECIFIC SAFETY RULES AND SYMBOLS

..... 6

DOUBLE INSULATION FOR SAFER

OPERATION ..................................... 8

FUNCTIONAL DESCRIPTION ................ 9

NAME OF PARTS ................................ 9

SPECIFICATIONS ................................ 9

Page

ASSEMBLY AND OPERATION ............ 10

APPLICATIONS ................................. 10

PRIOR TO OPERATION ..................... 10

HOW TO USE .................................... 12

HOW TO USE THE CORE BIT (FOR LIGHT LOAD)

... 16

MAINTENANCE AND INSPECTION .... 18

ACCESSORIES ...................................... 20

STANDARD ACCESSORIES ............. 20

OPTIONAL ACCESSORIES ............... 21

PARTS LIST .......................................... 74

TABLE DES MATIERES

Français

Page

INFORMATIONS IMPORTANTES DE SÉCURITÉ

... 26

SIGNIFICATION DES MOTS

D’AVERTISSEMENT ......................... 26

SECURITE ............................................. 27

REGLES GENERALE DE SECURITE

....... 27

REGLES DE SECURITE SPECIFIQUES ET SYMBOLES

... 29

DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR

........ 32

DESCRIPTION FONCTIONNELLE ........ 33

NOM DES PARTIES .......................... 33

SPECIFICATIONS .............................. 33

Page

ASSEMBLAGE ET FONCTIONNEMENT ....

34

APPLICATIONS ................................. 34

AVANT L’UTILISATION .................... 34

UTILISATION ..................................... 36

COMMENT UTILISER LA COURONNE (POUR

UNE CHARGE LEGERE)

.........................

40

ENTRETIEN ET INSPECTION ............... 42

ACCESSOIRES ...................................... 44

ACCESSOIRES STANDARD ............. 44

ACCESSOIRES SUR OPTION ........... 45

LISTA DES PIÈCES ............................... 74

ÍNDICE

Español

Página

INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD ...

50

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN ................................. 50

SEGURIDAD ......................................... 51

NORMAS GENERALES DE SEGURIDAD

... 51

NORMAS Y SÍMBOLOS ESPECÍFICOS DE SEGURIDAD

..... 53

AISLAMIENTO DOBLE PARA OFRECER UNA

OPERACIÓN MÁS SEGURA

................... 56

DESCRIPCIÓN FUNCIONAL ................ 57

NOMENCLATURA ............................. 57

ESPECIFICACIONES .......................... 57

Página

MONTAJE Y OPERACIÓN ................... 58

APLICACIONES ................................. 58

ANTES DE LA OPERACIÓN .............. 58

COMO SE USA .................................. 60

MODO DE USAR LA BARRENA TUBULAR

(PARA CARGAS LIGERAS)

................ 64

MANTENIMIENTO E INSPECCIÓN ..... 66

ACCESORIOS ....................................... 68

ACCESORIOS ESTÁNDAR ............... 68

ACCESORIOS OPCIONALES ............ 69

LISTA DE PIEZAS ................................. 74

3

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating

instructions in the Instruction Manual before operating or maintaining this power

tool.

Most accidents that result from power tool operation and maintenance are caused

by the failure to observe basic safety rules or precautions. An accident can often be

avoided by recognizing a potentially hazardous situation before it occurs, and by

observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction

Manual and in the sections which contain the operation and maintenance

instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are

identified by WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended

by HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result

in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may

result in minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

4

English

SAFETY

GENERAL SAFETY RULES

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric

shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas

invite accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases, or dust. Power tools create sparks

which may ignite the dust of fumes.

(3)Keep bystanders children, and visitors away while operating a power

tool. Distractions can cause you to lose control.

2. Electrical Safety

(1) Double Insulated tools are equipped with a polarized plug (one blade is

wider than the other.) This plug will fit in a polarized outlet only one

way. If the plug does not fit fully in the outlet, reverse the plug. If it still

does not fit, contact a qualified electrician to install a polarized outlet.

Do not change the plug in any way. Double Insulation

eliminates the

need for the three wire grounded power cord and grounded power supply

system.

(2) Avoid body contact with grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your

body is grounded.

(3) Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

(4) Do not abuse the cord. Never use the cord to carry the tools or pull the

plug from a receptacle. Keep cord away from heat, oil, sharp edges or

moving parts. Replace damaged cords immediately. Damaged cords

increase the risk of electric shock.

(5)When operating a power tool outside, use an outdoor extension cord

marked “W-A” or “W”. These cords are rated for outdoor use and reduce

the risk of electric shock.

3. Personal Safety

(1) Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use tool while tires or under the influence

of drugs, alcohol, or medication. A moment of inattention while operating

power tools may result in serious personal injury.

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing and gloves away from moving parts. Loose

clothes, jewelry, or long hair can be caught in moving parts.

5

English

(3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying

tools with your finger on the switch or plugging in tools that have the switch

on invites accidents.

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench

or a key that is left attached to a rotating part of the tool may result in

personal injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper

footing and balance enables better control of the tool in unexpected

situations.

(6) Use safety equipment. Always wear eye protection. Dust mask, non-skid

safety shoes, hard hat, or hearing protection must be used for appropriate

conditions.

4. Tool Use and Care

(1) Use clamps or other practical way to secure and support the workpiece

to a stable platform. Holding the work by hand or against your body is

unstable and may lead to loss of control.

(2) Do not force tool. Use the correct tool for your application. The correct

tool will do the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be

controlled with the switch is dangerous and must be repaired.

(4) Disconnect the plug form the power source before making any

adjustments, changing accessories, or storing the tool. Such preventive

safety measures reduce the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and other untrained persons.

Tools are dangerous in the hands of untrained users.

(6) Maintain tools with care. Keep cutting tools sharp and clean. Properly

maintained tools, with sharp cutting edges are less likely to bind and are

easier to control.

(7) Check for misalignment or binding of moving parts, breakage of parts,

and any other condition that may affect the tool's operation. If damaged,

have the tool serviced before using. Many accidents are caused by poorly

maintained tools.

(8) Use only accessories that are recommended by the manufacturer for

your model. Accessories that may be suitable for one tool, may become

hazardous when used with another tool.

5. Service

(1) Tool service must be performed only by qualified repair personnel. Service

or maintenance performed by unqualified personnel could result in a risk of

injury.

(2) When servicing a tool, use only identical replacement parts. Follow

instructions in the Maintenance section of this manual. Use of

unauthorized parts or failure to follow Maintenance Instruction may create

a risk of electric shock or injury.

6

English

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when performing an operation where

the cutting tool may contact hidden wiring or its own cord. Contact with a

“live” wire will make exposed metal parts of the tool “live” and shock the

operator.

2. ALWAYS wear ear protectors when using the tool for extended periods.

Prolonged exposure to high intensity noise can cause hearing

loss.

3. NEVER touch the tool bit with bare hands after operation.

4. NEVER wear gloves made from materials likely to roll up such as cotton, wool,

cloth or string, etc.

5. ALWAYS attach the side handle and securely grip the Rotary Hammer.

6. NEVER touch moving parts.

NEVER place your hands, fingers or other body parts near the tool’s moving

parts.

7. NEVER operate without all guards in place.

NEVER operate this tool without all guards or safety features in place and in

proper working order. If maintenance or servicing requires the removal of a

guard or safety feature, be sure to replace the guard or safety feature before

resuming operation of the tool.

8. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw

for cutting tree limbs or logs.

9. NEVER use a power tool for applications other than those specified.

NEVER use a power tool for applications other than those specified in the

Instruction Manual.

10. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or

throw the tool. NEVER allow the tool to be operated by children, individuals

unfamiliar with its operation or unauthorized personnel.

11. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition

periodically.

12. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools

should not be used until repaired.

13. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to yourself or others. Blades, cutting implements and

accessories which have been mounted to the tool should be secure and tight.

7

English

14. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that air can freely flow at all

times. Check for dust build-up frequently.

15. Operate power tools at the rated voltage.

Operate the power tool at voltages specified on its nameplate.

If using the power tool at a higher voltage than the rated voltage, it will result in

abnormally fast motor revolution and may damage the unit and the motor may

burn out.

16. NEVER use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

17. NEVER leave tool running unattended. Turn power off.

Don’t leave tool until it comes to a complete stop.

18. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently,

it may be deformed, cracked, or damaged.

19. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol

may damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

20. ALWAYS wear eye protection that meets the requirement of the latest revision

of ANSI Standard Z87.1.

21. ALWAYS be careful with buried object such as an underground wiring.

Touching live wiring or electric cable with this tool may result in electric shock.

Confirm before use whether hidden objects are present, such as electric cables

within the wall, floor or ceiling.

22. Definitions for symbols used on this tool

V ............ volts

Hz .......... hertz

A ............ amperes

no .......... no load speed

W ........... watt

........... Class II Construction

---/min ... revolutions per minute

.......... Alternating current

8

English

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation

design. “Double insulation” means that two physically separated insulation systems

have been used to insulate the electrically conductive materials connected to the

power supply from the outer frame handled by the operator. Therefore, either the

symbol “

” or the words “Double insulation” appear on the power tool or on the

nameplate.

Although this system has no external grounding, you must still follow the normal

electrical safety precautions given in this Instruction Manual, including not using

the power tool in wet environments.

To keep the double insulation system effective, follow these precautions:

Only Hitachi Authorized Service Center should disassemble or assemble this

power tool, and only genuine HITACHI replacement parts should be installed.

Clean the exterior of the power tool only with a soft cloth moistened with soapy

water, and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the

plastic may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

9

English

SPECIFICATIONS

Motor Single-Phase, Series Commutator Motor

Power Source Single-Phase, 120V 60Hz

Current 7.4A

Capacity Concrete: 5/32" – 1-3/16" (4mm – 30mm)

Steel: 1/2" (13mm)

Wood: 1-1/4" (32mm)

No-Load Speed 0 – 850/min.

Full-load Impact Rate 0 – 3,700/min.

Weight 9.5 lbs (4.3 kg)

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in

the safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first

read and understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments

that differ from those on your own power tool.

NAME OF PARTS

Housing

Nameplate

Drill bit

Tail cover

Grip

Side handle

Change lever

Stopper

Trigger

Set screw (under the tail cover)

Handle

Brush cap

(inside the tail cover)

Fig. 1

10

English

APPLICATIONS

Rotation and hammering function

Drilling anchor holes

Drilling holes in concrete

Drilling holes in tile

Rotation only function

Drilling in steel or wood (with optional accessories).

Tightening machine screws, wood screws (with optional accessories).

Hammering only function

Light-duty chiselling of concrete, groove digging and edging.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power source re-

quirements specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a recep-

tacle while the switch is in the ON position, the power tool will start operating

immediately and can cause serious injury.

3. Extension cord

When the work area is far away from the power source, use an extension cord of

sufficient thickness and rated capacity. The extension cord should be kept as

short as practicable.

WARNING:

Damaged cord must be replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired.

Contact a licensed electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in a seri-

ous hazard.

ASSEMBLY AND OPERATION

11

English

5. Confirming condition of the environment:

Confirm that the work site is placed under appropriate conditions conforming to

prescribed precautions.

6. Mounting the drill bit (Fig. 2)

CAUTION:

To prevent accidents, make sure to

turn the switch off and disconnect the

plug from the receptacle.

NOTE:

When using tools such as bull points,

drill bits, etc., make sure to use the

genuine parts designated by our

company.

(1) Clean the shank portion of the drill bit.

(2) To attach a drill bit (SDS-plus shank),

fully pull the grip in the direction of the

arrow as shown in Fig. 2 and insert the

drill bit as far as it will go while manu-

ally turning.

(3) By releasing the grip, the drill bit will

be secured.

(4) To remove the drill bit, fully pull the grip

in the direction of the arrow and pull

out the drill bit.

7. Installation of dust cup (Optional

accessories) (Fig. 3)

When using a rotary hammer for up-

ward drilling operations attach a dust

cup to collect dust or particles for easy

operation.

Installing the dust cup

Use the dust cup by attaching to the

drill bit a shown in Fig. 3.

When using a bit which has big

diameter, enlarge the center hole of the

dust cup with this rotary hammer.

CAUTION:

The dust cup is for exclusive use of concrete drilling work. Do not use them for

wood or metal drilling work.

Dump particles after every two or three holes when drilling.

Drill bit

Part of SDS-plus

shank

Grip

Front cap

Fig. 2

Dust cup

Fig. 3

12

English

8. Selecting the driver bit

Screw heads or bits will be damaged should an inappropriate bit for the screw

diameter be employed to drive in the screws.

9. Selecting the function mode

You can switch functions to the 3 modes of “hammering only, “rotation +

hammering”, and “rotation only” by turning the change lever while pressing

the push button. Set the

mark position of the change lever to that of the mode

to be used.

CAUTION:

Before operating the change lever, check and make sure that the motor has

stopped.

A failure can occur if it is operated while the motor is running.

To operate the change lever, press the push button, and release the lock of the

change lever. Also, check and make sure after operation that the push button

has returned and that the change lever has been locked.

Switch the change lever without mistake. If it is used at a position halfway,

there is a fear that the service life of the switching mechanism may be shortened.

HOW TO USE

CAUTION:

To prevent accidents, make sure to turn the switch off and disconnect the plug

from the receptacle when the drill bits and other various parts are installed or

removed. The power switch should also be turned off during a work break and

after work.

1. Switch operation

The rotation speed of the drill bit can be controlled steplessly by varying the

amount that the trigger switch is pulled. Speed is low when the trigger switch is

pulled slightly and increases as the switch is pulled more.

2. Rotation + Hammering

This rotary hammer can be set to

rotation and hammering mode by

pressing the push button and turning

the change lever to

mark. (Fig. 4)

Turn the grip slightly and confirm that

the clutch has been engaged with a

click.

Fig. 4

Change lever

Push

button

13

English

(1) Mount the drill bit.

(2) Pull the trigger switch after applying the

drill bit tip to the drilling position (Fig. 5)

(3) Pushing the rotary hammer forcibly is

not necessary at all. Pushing slightly so

that drill dust comes out gradually is

just sufficient.

CAUTION:

When the drill bit touches an iron reinforcing rod, the bit will stop immediately

and the rotary hammer will react to revolve. Therefore please grip the side

handle and handle tightly as shown in Fig. 5.

3. Rotation only

This rotary hammer can be set to

rotation only mode by pressing the

push button and turning the change

lever to

mark. (Fig. 6)

Turn the grip slightly and confirm that

the clutch has been engaged with a

click.

To drill a wood or metal material using

the separately sold drill chuck and chuck

adaptor, proceed as follows. Installing

drill chuck and chuck adaptor (Fig. 7):

(1) Attach the drill chuck to the chuck

adaptor.

(2) The part of the SDS-plus shank is the

same as the drill bit. Therefore, refer to

the item of “Mounting the drill bit” for

attaching it.

CAUTION:

Application of force more than necessary will not only reducing drilling

efficiency at all, but will deteriorate the tip edge of the drill bit and reduce the

service life of the rotary hammer in addition.

Drill bit may snap off while withdrawing the rotary hammer from the drilled

hole. For withdrawing, it is important to use a pushing motion.

Do not attempt to drill anchor holes or holes in concrete with the main unit in

the rotation only function.

Do not attempt to use the rotary hammer in the rotation and hammering func-

tion with the drill chuck and chuck adaptor attached. This would seriously

shorten the service life of every components of the machine.

Fig. 5

Fig. 6

Change lever

Push

button

Front cap

Grip

Fig. 7

Chuck

adaptor

Drill

chuck

Part of SDS-plus

shank

14

English

4. When driving machine screws

(Fig. 8)

First, insert the bit into the socket in the

end of chuck adaptor (D).

Next, mount chuck adaptor (D) on the

main unit using procedures described

in 6 (1), (2), (3), put the tip of the bit in

the slots in the head of the screw, grasp

the main unit and tighten the screw.

CAUTION:

Exercise care not to excessively prolong driving time, otherwise, the screws

may be damaged by excessive force.

Apply the rotary hammer perpendicularly to the screw head when driving a

screw; otherwise, the screw head or bit will be damaged, or driving force will

not be fully transferred to the screw.

Do not attempt to use the rotary hammer in the rotation and hammering func-

tion with chuck adaptor (D) and bit attached.

5. When driving wood screws (Fig. 8)

(1) Selecting a suitable driver bit

Employ phillips screws, if possible, since the driver bit easily slips off the heads

of slotted-head screws.

(2) Driving in wood screws

Prior to driving in wood screws, make pilot holes suitable for them in the wooden

board. Apply the bit to the screw head grooves and gently drive the screws into

the holes.

After rotating the rotary hammer at low speed for a while until a wood screw in

partly driven into the wood, squeeze the trigger more strongly to obtain the

optimum driving force.

CAUTION:

Exercise care in preparing a pilot hole suitable for the wood screw taking the

hardness of the wood into consideration. Should the hole be excessively small

or shallow, requiring much power to drive the screw into it, the thread of the

wood screw may sometimes be damaged.

Bit

Socket

Chuck

adaptor (D) Front cap

Grip

Fig. 8

15

English

6. Hammering only

This rotary hammer can be set to

hammering only mode by pressing the

push button and turning the change

lever to

mark. (Fig. 9)

(1) Mount the bull point or cold chisel.

(2) Press the push button and set the

change lever to

mark.

The rotation is released, turn the grip

and adjust the cold chisel to desired

position. (Fig. 10)

(3) Turn the change lever to

mark.

(Fig. 9)

Then bull point or cold chisel is locked.

7. Using the stopper (Fig. 11)

(1) Loosen the side handle, and insert the

stopper into the handle bolt hole.

(2) Adjust the stopper position according

to the depth of the hole and tighten the

side handle securely.

8. How to use the drill bit (taper shank)

and the taper shank adaptor.

(1) Mount the taper shank adaptor to the

rotary hammer. (Fig. 12)

(2) Mount the drill bit (taper shank) to the

taper shank adaptor. (Fig. 12)

(3) Turn the switch ON, and drill a hole in

prescribed depth.

(4) To remove the drill bit (taper shank),

insert the cotter into the slot of the taper

shank adaptor and strike the head of

the cotter with a hammer supporting

on the rests. (Fig. 13)

Fig. 10

Grip

Handle bolt

Stopper

Knob on side

handle

Fig. 11

Change lever

Push button

Fig. 9

Fig. 12

Drill bit

Taper shank

adaptor

Front cap

Grip

Cotter

Rests

Taper shank adaptor

Fig. 13

16

English

9. Using the side handle

When you wish to change a position of the side handle, turn grip of the side

handle counterclockwise to loosen it, and then fasten it firmly.

CAUTION:

When boring a hole, there can be a case where the machine attempts to rotate

by the reaction at the time of penetrating a concrete wall and/or when a tip of

the blade comes in contact with the rebar.

Firmly fasten the side handle and hold the machine with both of your hands.

Unless you hold it securely, an accident can occur.

HOW TO USE THE CORE BIT (FOR LIGHT LOAD)

When boring penetrating large hole use the core bit (for light load). At that time use

with the center pin and the core bit shank provided as optional accessories.

1. Mounting

CAUTION:

Be sure to turn power OFF and discon-

nect the plug from the receptacle.

(1) Mount the core bit to the core bit shank.

(Fig. 14)

Lubricate the thread of the core bit

shank to facilitate disassembly.

(2) Mount the core bit shank to the rotary

hammer. (Fig. 15)

(3) Insert the center pin into the guide plate

until it stops.

(4) Engage the guide plate with the core

bit, and turn the guide plate to left or

right so that it does not fall even if it

faces downward. (Fig. 16)

Fig. 15

Fig. 14

Core bit

Thread

Core bit shank

Fig. 16

Core bit

Core bit tip

Guide plate

Center pin

17

English

2. How to bore (Fig. 17)

(1) Connect the plug to the power source.

(2) A spring is installed in the center pin.

Push it lightly to the wall or the floor

straight. Connect all over the surface

of the core bit tip and start operating.

(3) When boring about 3/16" (5 mm) in

depth the position of the hole will

establish. Bore after that removing the

center pin and the guide plate from core

bit.

(4) Application of excessive force will not only expedite the work, but will deteriorate

the tip edge of the drill bit, resulting in reduced service life of the rotary hammer.

CAUTION:

When removing the center pin and the guide plate, turn OFF the switch and

disconnect the plug form the receptacle.

3. Dismounting. (Fig. 18)

Remove the core bit shank from the

rotary hammer and strike the head of

the core bit shank strongly two or three

times with the manual hammer hold-

ing the core bit, then the thread be-

comes loose and the core bit can be

removed.

Fig. 17

Fig. 18

Core bit shank

18

English

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle during maintenance and inspection.

1. Inspecting the drill bits

Since use of a dull tool will cause motor malfunctioning and degraded efficiency,

replace the drill bit with a new one or resharpening without delay when abrasion

is noted.

2. Inspecting the screws

Regularly inspect all screws and ensure that they are properly tightened. Should

any of the screws be loosened, retighten them immediately.

WARNING: Using this rotary hammer with loosen screws is extremely

dangerous.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power tool. Exercise due care

to ensure the winding does not become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes: (Fig. 19)

The motor employs carbon brushes which are consumable parts. When they

become worn to or near “wear limit”, it could result in motor trouble. When an

auto-stop carbon brush is equipped, the motor will stop automatically. At that

time, replace both carbon brushes with new ones which have the same carbon

brush Nos. shown in the figure.

In addition, always keep carbon brushes clean and ensure that they slide freely

within the brush holders.

CAUTION: Using this rotary hammer with a carbon brush which is worn in

excess of the wear limit will damage the motor.

NOTE: Use HITACHI carbon brush No.73 indicated in Fig. 19.

Wear limit

No. of carbon brush

0.28" (7 mm)

0.67" (17 mm)

73

Fig. 19

19

English

Replacing carbon brushes:

(For parts name, refer to Fig. 1)

Loosen the two set screws and remove the tail cover. Remove the brush caps

and carbon brushes. After replacing the carbon brushes, tighten the brush caps

securely and to install the tail cover with securely tightening two set screws.

5. How to replase grease

This machine is full air-tight construction to protect against dust and to prevent

lubricant leakage. Therefore, the machine can be used without lubrication for

long periods. Replace the grease as described below.

Grease replacement period

You should look at the grease when you change the carbon brush. (See item 4 in

the section MAINTENANCE AND INSPECTION.) Ask for grease replacement at

the nearest HITACHI Authorized Service Center. Proceed for replacement of

grease.

Grease replenishment

CAUTION: Before replenishing the grease, turn the power off and pull out the

power plug.

(1) Disassemble the crank case cover and

thoroughly wipe off the old grease

inside. (Fig. 20)

(2) Supply 1.0 oz (30g) of Hitachi Electric

Hammer Grease A (standard accessory,

contained in tube) in the crank case.

(3) After replacing the grease, reassemble

the crank case cover securely. At this

time, do not damage or lose the oil seal.

NOTE: The HITACHI Electric Hammer

Grease A is of the lower

viscosity type. When the

supplied grease tube is

consumed, purchase from a

HITACHI Autorized Service

Center.

6. Service and repairs

All quality power tools will eventually require servicing or replacement of parts

because of wear from normal use. To assure that only authorized replacement

parts will be used, all service and repairs must be performed by a Hitachi

Authorized Service Center, ONLY.

Crank case cover

Fig. 20

20

English

ACCESSORIES

WARNING: ALWAYS use Only authorized HITACHI replacement parts and

accessories. NEVER use replacement parts or accessories which

are not intended for use with this tool. Contact HITACHI if you

are not sure whether it is safe to use a particular replacement

part or accessory with your tool.

The use of any other attachment or accessory can be dangerous

and could cause injury or mechanical damage.

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

(1) Plastic Case (Code No. 325679) ..............................................................................1

(2) Side Handle (Code No. 313078)..............................................................................1

(3) Stopper (Code No. 971786).....................................................................................1

(4) Dust Cup (Code No. 971787)...................................................................................1

(5) Syringe (Code No. 318085) .....................................................................................1

7. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION: Repair, modification and inspection of Hitachi Power Tools must be

carried out by an Hitachi Authorized Service Center.

This Parts List will be helpful if presented with the tool to the Hitachi

Authorized Service Center when requesting repair or other

maintenance. In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each country must

be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved and modified to incorporate

the latest technological advancements.

Accordingly, some parts (i.e. code numbers and/or design) may be changed

without prior notice.

La page charge ...

Hitachi DH 30PC2 Manuel utilisateur

Ce manuel convient également à

Hitachi DH 30PC2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents