Sony CDX-GT740UI Le manuel du propriétaire

Operating Instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

DE

GB

4-159-947-21 (1)

CDX-GT740UI

FR

IT

NL

To cancel the demonstration (Demo) display, see page 6.

Zum Deaktivieren der Demo-Anzeige (Demo) schlagen Sie bitte auf Seite 6 nach.

Pour annuler la démonstration (Demo), reportez-vous à la page 6.

Per annullare la dimostrazione (Demo), vedere pagina 6.

Om de demonstratie (Demo) te annuleren, zie pagina 6.

FM/MW/LW

Compact Disc Player

FM/MW/LW Compact Disc Player

2

ZAPPIN is a trademark of Sony Corporation.

iPod is a trademark of Apple Inc., registered in

the U.S. and other countries.

iPhone is a trademark of Apple Inc.

Be sure to install this unit in the dashboard of

the car for safety. For installation and

connections, see the supplied installation/

connections manual.

This label is located on the bottom of the

chassis.

Notice for customers: the following

information is only applicable to

equipment sold in countries applying

EU Directives

The manufacturer of this product is Sony

Corporation, 1-7-1 Konan, Minato-ku, Tokyo,

Japan. The Authorized Representative for EMC

and product safety is Sony Deutschland GmbH,

Hedelfinger Strasse 61, 70327 Stuttgart,

Germany. For any service or guarantee matters

please refer to the addresses given in separate

service or guarantee documents.

Disposal of Old Electrical &

Electronic Equipment (Applicable in

the European Union and other

European countries with separate

collection systems)

This symbol on the product or on its

packaging indicates that this product shall not be treated

as household waste. Instead it shall be handed over to the

applicable collection point for the recycling of electrical

and electronic equipment. By ensuring this product is

disposed of correctly, you will help prevent potential

negative consequences for the environment and human

health, which could otherwise be caused by inappropriate

waste handling of this product. The recycling of materials

will help to conserve natural resources. For more detailed

information about recycling of this product, please contact

your local Civic Office, your household waste disposal

service or the shop where you purchased the product.

Applicable accessory: Remote commander

Disposal of waste batteries

(applicable in the European Union

and other European countries with

separate collection systems)

This symbol on the battery or on the packaging indicates

that the battery provided with this product shall not be

treated as household waste. On certain batteries this

symbol might be used in combination with a chemical

symbol. The chemical symbols for mercury (Hg) or lead

(Pb) are added if the battery contains more than 0.0005%

mercury or 0.004% lead. By ensuring these batteries are

disposed of correctly, you will help prevent potentially

negative consequences for the environment and human

health which could otherwise be caused by inappropriate

waste handling of the battery. The recycling of the

materials will help to conserve natural resources.

In case of products that for safety, performance or data

integrity reasons require a permanent connection with an

incorporated battery, this battery should be replaced by

qualified service staff only. To ensure that the battery will

be treated properly, hand over the product at end-of-life to

the applicable collection point for the recycling of

electrical and electronic equipment.

For all other batteries, please view the section on how to

remove the battery from the product safely. Hand the

battery over to the applicable collection point for the

recycling of waste batteries.

For more detailed information about recycling of this

product or battery, please contact your local Civic Office,

your household waste disposal service or the shop where

you purchased the product.

Windows Media and the

Windows logo are trademarks

or registered trademarks of

Microsoft Corporation in the

United States and/or other countries.

MPEG Layer-3 audio coding technology and

patents licensed from Fraunhofer IIS and Thomson.

This product is protected by certain intellectual

property rights of Microsoft Corporation. Use or

distribution of such technology outside of this

product is prohibited without a license from

Microsoft or an authorized Microsoft subsidiary.

3

Warning if your car’s ignition has no

ACC position

Be sure to set the Auto Off function (page 20).

The unit will shut off completely and

automatically in the set time after the unit is

turned off, which prevents battery drain.

If you do not set the Auto Off function, press

and hold (OFF) until the display disappears

each time you turn the ignition off.

Content providers are using the digital rights

management technology for Windows Media

contained in this device (“WM-DRM”) to protect

the integrity of their content (“Secure Content”) so

that their intellectual property, including copyright,

in such content is not misappropriated.

This device uses WM-DRM software to play

Secure Content (“WM-DRM Software”). If the

security of the WM-DRM Software in this device

has been compromised, owners of Secure Content

(“Secure Content Owners”) may request that

Microsoft revoke the WM-DRM Software’s right

to acquire new licenses to copy, display and/or

play Secure Content. Revocation does not alter the

WM-DRM Software’s ability to play unprotected

content. A list of revoked WM-DRM Software is

sent to your device whenever you download a

license for Secure Content from the Internet or

from a PC. Microsoft may, in conjunction with

such license, also download revocation lists onto

your device on behalf of Secure Content Owners.

Note on the lithium battery

Do not expose the battery to excessive heat such as

direct sunlight, fire or the like.

4

Table of Contents

Getting Started

Playable discs on this unit . . . . . . . . . . . . . . . . . 6

Resetting the unit. . . . . . . . . . . . . . . . . . . . . . . . 6

Canceling the Demo mode . . . . . . . . . . . . . . . . 6

Preparing the card remote commander . . . . . . . 6

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . 6

Detaching the front panel . . . . . . . . . . . . . . . . . 7

Attaching the front panel . . . . . . . . . . . . . . . 7

Location of controls and basic

operations

Main unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Card remote commander RM-X174 . . . . . . . 8

Searching for a track . . . . . . . . . . . . . . . . . . . . 10

Searching a track by name

— Quick-BrowZer . . . . . . . . . . . . . . . . . . . 10

Searching a track by listening to track passages

— ZAPPIN™ . . . . . . . . . . . . . . . . . . . . . . . 10

Radio

Storing and receiving stations . . . . . . . . . . . . . 11

Storing automatically — BTM . . . . . . . . . . 11

Storing manually. . . . . . . . . . . . . . . . . . . . . 11

Receiving the stored stations . . . . . . . . . . . 11

Tuning automatically . . . . . . . . . . . . . . . . . 11

Receiving a station through a list

— LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Setting AF and TA . . . . . . . . . . . . . . . . . . . 13

Selecting PTY . . . . . . . . . . . . . . . . . . . . . . . 13

Setting CT. . . . . . . . . . . . . . . . . . . . . . . . . . 13

CD

Playing a disc. . . . . . . . . . . . . . . . . . . . . . . . . . 14

Display items . . . . . . . . . . . . . . . . . . . . . . . 14

Repeat and shuffle play. . . . . . . . . . . . . . . . 14

USB devices

Playing back a USB device. . . . . . . . . . . . . . . 15

Display items . . . . . . . . . . . . . . . . . . . . . . . 15

Repeat and shuffle play . . . . . . . . . . . . . . . 16

iPod

Playing back iPod . . . . . . . . . . . . . . . . . . . . . . 16

Display items . . . . . . . . . . . . . . . . . . . . . . . 17

Setting the play mode . . . . . . . . . . . . . . . . . . . 18

Repeat and shuffle play . . . . . . . . . . . . . . . 18

Operating an iPod directly

— Passenger control . . . . . . . . . . . . . . . . . . . . 18

Other functions

Changing the sound settings . . . . . . . . . . . . . . 19

Adjusting the sound characteristics . . . . . . 19

Customizing the equalizer curve

— EQ3 Parametric Tune . . . . . . . . . . . . . . 19

Adjusting setup items — SET . . . . . . . . . . . . 20

Using optional equipment. . . . . . . . . . . . . . . . 21

Auxiliary audio equipment. . . . . . . . . . . . . 21

Additional Information

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Notes on discs . . . . . . . . . . . . . . . . . . . . . . 22

Playback order of MP3/WMA/AAC

files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

About iPod . . . . . . . . . . . . . . . . . . . . . . . . . 22

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Removing the unit. . . . . . . . . . . . . . . . . . . . . . 24

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 24

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 25

Error displays/Messages. . . . . . . . . . . . . . . 27

5

Support site

If you have any questions or for the latest support information on this

product, please visit the web site below:

http://support.sony-europe.com/

Provides information on:

• Models and manufacturers of compatible digital audio players

• Supported MP3/WMA/AAC files

6

Getting Started

Playable discs on this unit

This unit can play CD-DA (also containing CD

TEXT) and CD-R/CD-RW (MP3/WMA/AAC

files (page 22)).

Resetting the unit

Before operating the unit for the first time, or

after replacing the car battery or changing the

connections, you must reset the unit.

Detach the front panel (page 7) and press the

RESET button (page 8) with a pointed object,

such as a ball-point pen.

Note

Pressing the RESET button will erase the clock setting

and some stored contents.

Canceling the Demo mode

You can cancel the demonstration display which

appears during turning off.

1 Press and hold the control dial.

The setup display appears.

2 Rotate the control dial until “Demo”

appears, then press it.

3 Rotate the control dial to select “off.”

then press it.

The setting is complete.

4 Press (BACK).

The display returns to normal play/reception

mode.

Preparing the card remote

commander

Remove the insulation film.

Tip

For how to replace the battery, see page 23.

Setting the clock

The clock uses a 24-hour digital indication.

1 Press and hold the control dial.

The setup display appears.

2 Rotate the control dial until “Clock

Adjust” appears.

3 Press the control dial.

4 Rotate the control dial to set the hour,

then press it.

5 Rotate the control dial to set the

minute, then press it.

To move the digital indication, press the

control dial/ (back) +/–.

The setup is complete and the clock starts.

Tip

You can set the clock automatically with the RDS

feature (page 13).

Type of discs Label on the disc

CD-DA

MP3

WMA

AAC

7

Detaching the front panel

You can detach the front panel of this unit to

prevent theft.

Caution alarm

If you turn the ignition switch to the OFF

position without detaching the front panel, the

caution alarm will sound for a few seconds.

The alarm will only sound if the built-in

amplifier is used.

1 Press (OFF).

The unit is turned off.

2 Press (OPEN).

The front panel is flipped down.

3 Slide the front panel to the right, then

gently pull out the left end of the front

panel.

Notes

• Do not drop or put excessive pressure on the front

panel and display window.

• Do not subject the front panel to heat/high

temperature or moisture. Avoid leaving it in a parked

car or on a dashboard/rear tray.

• Do not detach the front panel during playback of the

USB device, otherwise USB data may be damaged.

Attaching the front panel

Place the hole A of the front panel onto the

spindle B on the unit, then lightly push the left

side in.

Press (SOURCE) on the unit (or insert a disc) to

operate the unit.

Note

Do not put anything on the inner surface of the front

panel.

8

Location of controls and basic operations

Main unit

Front panel removed

Card remote commander

RM-X174

This section contains instructions on the location

of controls and basic operations. For details, see

the respective pages.

The corresponding buttons on the card remote

commander control the same functions as those

on the unit.

A OFF button

To turn off; stop the source.

B (BACK) button

To return to the previous display.

C SOURCE button

To turn on; change the source (Radio/CD/

USB/AUX).

D ZAP button page 11

To enter ZAPPIN™ mode.

E Control dial/ENTER/SOUND/MENU

button

Rotate to adjust the volume/adjust a setting.

Press to enter sound setting/apply a setting.

Press and hold to enter menu.

F Receptor for the card remote

commander

G Display window

H OPEN button page 7, 14

I USB connector page 15, 16

To connect to the USB device.

J SEEK +/– buttons

CD/USB:

To skip tracks (press); skip tracks

continuously (press, then press again within

about 1 second and hold); reverse/fast-

forward a track (press and hold).

Radio:

To tune in stations automatically (press); find

a station manually (press and hold).

ALBUMREP SHUF

OFF

SOURCE

MODE

ZAP

SEEK

DSPLAF

/

TA

OPEN

PAUSEDM

312 456

AUX

SCRLPTY

PUSH ENTER/SOUND/

MENU

1

qaq;

2

qs qh

qf

4 65 7

8

9

3

qgqd

RESET

q

k

q

l

q

j

OFF

SCRL

SOURCE

MODE

132

465

ATT

VOL

+

–

+

–

DSPL/PTY

ENTER

REP SHUF

MENU

SOUND

PAU SE

3

wh

qa

1

wk

w;

wd

wg

wf

wl

wj

wa

ws

qs

9

K MODE button page 11, 17, 18

Press to select the radio band (FM/MW/LW)/

select the play mode of iPod.

Press and hold to enter/cancel the passenger

control.

L (LIST/BROWSE) button page 10,

12

To list up (Radio); enter the Quick-BrowZer

mode (CD/USB).

M AF (Alternative Frequencies)/

TA (Traffic Announcement)/

PTY (Program Type) button page 13

To set AF and TA (press); select PTY (press

and hold) in RDS.

N Number buttons

CD/USB:

(1): REP page 14, 16, 18

(2): SHUF page 14, 16, 18

(3)*/(4): ALBUM –*/+ (during MP3/

WMA/AAC playback)

To skip albums (press); skip albums

continuously (press and hold).

(5): DM+

Improves digitally compressed sound,

such as MP3.

To activate the DM+ function, set

“ON.” To cancel, set “OFF.”

(6): PAUSE

To pause playback. To cancel, press

again.

Radio:

To receive stored stations (press); store

stations (press and hold).

O DSPL (display)/SCRL (scroll) button

page 14, 15, 17

To change display items (press); scroll the

display item (press and hold).

P AUX input jack page 21

To connect a portable audio device.

Q RESET button page 6

R Z (eject) button page 14

To eject the disc.

S Disc slot

To insert the disc.

The following buttons on the card remote

commander have also different buttons/functions

from the unit. Remove the insulation film before

use (page 6).

w; < (.)/, (>) buttons

To control CD/radio/USB, the same as

(SEEK) –/+ on the unit.

Setup, sound setting, etc., can be operated by

< ,.

wa MENU button

To enter menu.

ws ENTER button

To apply a setting.

wd DSPL (display)/PTY (Program Type)

button page 13, 14, 15, 17

To change display items; select PTY in RDS.

wf VOL (volume) +

*/– button

To adjust volume.

wg ATT (attenuate) button

To attenuate the sound. To cancel, press

again.

wh SOUND button

To enter sound setting.

wj M (+)/m (–) buttons

To control CD/USB, the same as (3)/(4)

(ALBUM –/+) on the unit.

Setup, sound setting, etc., can be operated by

M m.

wk SCRL (scroll) button

To scroll the display item.

wl Number buttons

To receive stored stations (press); store

stations (press and hold).

* This button has a tactile dot.

Note

If the unit is turned off and the display disappears, it

cannot be operated with the card remote commander

unless (SOURCE) on the unit is pressed, or a disc is

inserted to activate the unit first.

10

Searching for a track

Searching a track by name

— Quick-BrowZer

You can search for a track in a CD or USB device

easily by category.

1 Press (LIST/BROWSE).

The unit enters the Quick-BrowZer mode,

and the list of search categories appears.

2 Rotate the control dial to select the

desired search category, then press it

to confirm.

3 Repeat step 2 until the desired track is

selected.

Playback starts.

To return to the previous display

Press (BACK).

To exit the Quick-BrowZer mode

Press (LIST/BROWSE).

Note

When entering the Quick-BrowZer mode, the repeat/

shuffle setting is canceled.

Searching by skip items

— Jump mode

When many items are in a category, you can

search the desired item quickly.

1 Press (SEEK) + in Quick-BrowZer mode.

The following display appears.

A Current item number

B Total item number in the current layer

C Item name

Then the item name will appear.

2 Rotate the control dial to select the desired

item, or one near the desired item.

It skips in steps of 10% of the total item

number.

3 Press the control dial.

The display returns to the Quick-BrowZer

mode and the selected item appears.

4 Rotate the control dial to select the desired

item and press it.

Playback starts if the selected item is a track.

To cancel Jump mode

Press (BACK) or (SEEK) –.

Searching a track by listening to

track passages — ZAPPIN™

While playing back short track passages in a CD

or USB device in sequence, you can search for a

track you want to listen to.

ZAPPIN mode is suitable for searching for a

track in shuffle or shuffle repeat mode.

(LIST/BROWSE)

OFF

SOURCE

MODE

ZAP

SEEK

Control dial

(BACK)

SEEK +/–

A

B

C

OFF

SOURCE

MODE

ZAP

SEEK

ZAP

Control dial

(BACK)

11

1 Press (ZAP) during playback.

Playback starts from a passage of the next

track.

The passage is played for the set time, then a

click sounds and the next passage starts.

2 Press the control dial or (ZAP) when a

track you want to listen is played back.

The track that you select returns to normal

play mode from the beginning.

To search a track by ZAPPIN mode again,

repeat steps 1 and 2.

Tips

• You can select the playback time from about 6

seconds/9 seconds/30 seconds (page 21). You

cannot select the passage of the track to playback.

• Press (SEEK) –/+ or (3)/(4) (ALBUM –/+) in

ZAPPIN mode to skip a track or album.

• Pressing (BACK) also confirms a track to

playback.

Radio

Storing and receiving stations

Caution

When tuning in stations while driving, use Best

Tuning Memory (BTM) to prevent an accident.

Storing automatically — BTM

1 Press (SOURCE) repeatedly until

“TUNER” appears.

To change the band, press (MODE)

repeatedly. You can select from FM1, FM2,

FM3, MW, or LW.

2 Press and hold the control dial.

The setup display appears.

3 Rotate the control dial until “BTM”

appears, then press it.

The unit stores stations in order of frequency

on the number buttons.

A beep sounds when the setting is stored.

Storing manually

1 While receiving the station that you

want to store, press and hold a

number button ((1) to (6)) until

“MEM” appears.

Note

If you try to store another station on the same number

button, the previously stored station will be replaced.

Tip

When an RDS station is stored, the AF/TA setting is

also stored (page 13).

Receiving the stored stations

1 Select the band, then press a number

button ((1) to (6)).

Tuning automatically

1 Select the band, then press (SEEK) +/–

to search for the station.

Scanning stops when the unit receives a

station. Repeat this procedure until the

desired station is received.

Tip

If you know the frequency of the station you want to

listen to, press and hold (SEEK) +/– to locate the

approximate frequency, then press (SEEK) +/–

repeatedly to fine adjust to the desired frequency

(manual tuning).

ZAP

1

2

3

4

The part of each track to

playback in ZAPPIN mode.

Track

12

Receiving a station through a list

— LIST

You can list up the frequency.

1 Select the band, then press (LIST/

BROWSE).

The preset list appears.

2 Rotate the control dial until the

desired station appears.

3 Press the control dial to receive the

station.

The display returns to normal reception

mode.

RDS

Overview

FM stations with Radio Data System (RDS)

service send inaudible digital information along

with the regular radio program signal.

Display items

A Radio band, Function

B TP/TA/AF*

1

C Clock

D Preset number

E Frequency*

2

(Program service name), RDS

data

*1 When Information “on” is set:

– “TP” lights up while “TP” is received.

– “TA”/“AF” lights up while “TA/AF” is on.

*2 While receiving the RDS station, “RDS” is

displayed on the left of the frequency indication.

RDS services

This unit automatically provides RDS services as

follows:

Notes

• Depending on the country/region, not all RDS

functions may be available.

• RDS will not work if the signal strength is too weak,

or if the station you are tuned to is not transmitting

RDS data.

AF (Alternative Frequencies)

Selects and retunes the station with the

strongest signal in a network. By using this

function, you can continuously listen to the

same program during a long-distance drive

without having to retune the same station

manually.

TA (Traffic Announcement)/TP (Traffic

Program)

Provides current traffic information/programs.

Any information/program received, will

interrupt the currently selected source.

PTY (Program Types)

Displays the currently received program type.

Also searches your selected program type.

CT (Clock Time)

The CT data from the RDS transmission sets

the clock.

A B C

D E

13

Setting AF and TA

1 Press (AF/TA) repeatedly until the

desired setting appears.

Storing RDS stations with the AF and

TA setting

You can preset RDS stations along with the AF/

TA setting. If you use the BTM function, only

RDS stations are stored with the same AF/TA

setting.

If you preset manually, you can preset both RDS

and non-RDS stations with the AF/TA setting for

each.

1 Set AF/TA, then store the station with BTM or

manually.

Receiving emergency

announcements

With AF or TA on, the emergency

announcements will automatically interrupt the

currently selected source.

Tip

If you adjust the volume level during a traffic

announcement, that level will be stored into memory

for subsequent traffic announcements, independently

from the regular volume level.

Staying with one regional program

— Regional

When the AF function is on: this unit’s factory

setting restricts reception to a specific region, so

you will not be switched to another regional

station with a stronger frequency.

If you leave this regional program’s reception

area, set “Regional off” in setup during FM

reception (page 21).

Note

This function does not work in the UK and in some

other areas.

Local Link function (UK only)

This function enables you to select other local

stations in the area, even if they are not stored on

your number buttons.

1 During FM reception, press a number button

((1) to (6)) on which a local station is stored.

2 Within 5 seconds, press again a number button

of the local station.

Repeat this procedure until the local station is

received.

Selecting PTY

1 Press and hold (AF/TA) (PTY) during

FM reception.

The current program type name appears if the

station is transmitting PTY data.

2 Rotate the control dial until the

desired program type appears.

3 Press the control dial.

The unit starts to search for a station

broadcasting the selected program type.

Type of programs

Note

You cannot use this function in countries/regions

where no PTY data is available.

Setting CT

1 Set “CT on” in setup (page 20).

Notes

• The CT function may not work even though an RDS

station is being received.

• There might be a difference between the time set by

the CT function and the actual time.

Select To

AF on activate AF and deactivate TA.

TA on activate TA and deactivate AF.

AF/TA on activate both AF and TA.

AF/TA off deactivate both AF and TA.

News (News), Current Affairs (Current

Affairs), Information (Information), Sport

(Sports), Education (Education), Drama

(Drama), Cultures (Culture), Science

(Science), Varied Speech (Varied), Pop

Music (Pop Music), Rock Music (Rock

Music), Easy Listening (M.O.R. Music),

Light Classics M (Light classical), Serious

Classics (Serious classical), Other Music

(Other Music), Weather & Metr (Weather),

Finance (Finance), Children’s Progs

(Children’s Program), Social Affairs (Social

Affairs), Religion (Religion), Phone In

(Phone In), Travel & Touring (Travel),

Leisure & Hobby (Leisure), Jazz Music

(Jazz Music), Country Music (Country

Music), National Music (National Music),

Oldies Music (Oldies Music), Folk Music

(Folk Music), Documentary (Documentary)

14

CD

Playing a disc

1 Press (OPEN).

2 Insert the disc (label side up).

3 Close the front panel.

Playback starts automatically.

Ejecting the disc

1 Press (OPEN).

2 Press Z.

The disc is ejected.

3 Close the front panel.

Display items

To change display items, press (DSPL).

A Source

B Clock

C Track name*, Artist name*, Disc/album

name*

D EQ3 Parametric Preset/DM+ Advanced/

ZAPPIN/Repeat/Shuffle

A Source

B Clock

E Artist name*, Disc/album name*, Track

name*, Disc/Album number, Track number,

Elapsed playing time

* The information of a CD TEXT, MP3/WMA/AAC is

displayed.

Tip

Displayed items will differ depending on the disc type,

recording format and settings.

Repeat and shuffle play

1 During playback, press (1) (REP) or

(2) (SHUF) repeatedly until the

desired setting appears.

* When an MP3/WMA/AAC is played.

To return to normal play mode, select “Repeat

Off” or “Shuffle Off.”

A

B

DC

A

B

E

Select To play

Repeat Track track repeatedly.

Repeat Album* album repeatedly.

Shuffle Album* album in random order.

Shuffle Disc disc in random order.

15

USB devices

For details on the compatibility of your USB

device, visit the support site.

• MSC (Mass Storage Class) and MTP (Media

Transfer Protocol) type USB devices compliant

with the USB standard can be used.

• Corresponding codec is MP3 (.mp3), WMA

(.wma) and AAC (.m4a).

• Backup of data in a USB device is

recommended.

Note

Connect the USB device after starting the engine.

Depending on the USB device, malfunction or damage

may occur if it is connected before starting the engine.

Playing back a USB device

1 Slide the USB cover.

2 Connect the USB device to the USB

connector.

When using a cable, use the one supplied with

the USB device to connect.

Playback starts.

If a USB device is already connected, to start

playback, press (SOURCE) repeatedly until

“USB” appears.

Press (OFF) to stop playback.

Removing the USB device

1 Stop the USB device playback.

2 Remove the USB device.

If you remove your USB device during

playback, data in the USB device may be

damaged.

Notes

• Do not use USB devices so large or heavy that they

may fall down due to vibration, or cause a loose

connection.

• Do not detach the front panel during playback of the

USB device, otherwise USB data may be damaged.

• This unit cannot recognize USB devices via a USB

hub.

• If the USB is disconnected during playback, “NO

Device” appears in the display of the unit.

Display items

To change display items, press (DSPL).

A Source

B Clock

C Track name, Artist name, Album name

D EQ3 Parametric Preset/DM+ Advanced/

ZAPPIN/Repeat/Shuffle

A Source

B Clock

E Artist name, Album name, Track name,

Album number, Track number, Elapsed

playing time

Support site

http://support.sony-europe.com/

continue to next page t

A

B

DC

A

B

E

16

Notes

• Displayed items will differ, depending on the USB

device, recorded format and settings.

• The maximum number of displayable data is as

follows.

– folders (albums): 128

– files (tracks) per folder: 512

• Do not leave a USB device in a parked car, as

malfunction may result.

• It may take time for playback to begin, depending on

the amount of recorded data.

• DRM (Digital Rights Management) files may not be

played.

• During playback or fast-forward/reverse of a VBR

(Variable Bit Rate) MP3/WMA/AAC file, elapsed

playing time may not display accurately.

• Playback of the following MP3/WMA/AAC files is not

supported.

– lossless compression

– copyright-protected

Repeat and shuffle play

1 During playback, press (1) (REP) or

(2) (SHUF) repeatedly until the

desired setting appears.

After 3 seconds, the setting is complete.

To return to normal play mode, select “Repeat

off” or “Shuffle off.”

iPod

For details on the compatibility of your iPod, see

“About iPod” on page 22 or visit the support site.

In these Operating Instructions, “iPod” is used as

a general reference for the iPod functions on the

iPod and iPhone, unless otherwise specified by

the text or illustrations.

Playing back iPod

Before connecting the iPod, turn down the

volume of the unit.

1 Slide the USB cover.

2 Connect the iPod to the USB

connector via the dock connector to

USB cable.

The iPod will turn on automatically, and the

display will appear on the iPod screen as

below.*

Tip

We recommend the RC-100IP USB cable (not

supplied) to connect the dock connector.

Select To play

Repeat Track track repeatedly.

Repeat Album album repeatedly.

Shuffle Album album in random order.

Shuffle Device device in random order.

Support site

http://support.sony-europe.com/

>

.

M

E

N

U

17

The tracks on the iPod start playing

automatically from the point last played.

If an iPod is already connected, to start

playback press (SOURCE) repeatedly until

“USB” or “iPod” appears.

* In the case of an iPod touch or iPhone being

connected, or that the iPod was last played back

using passenger control, the logo will not appear on

the screen.

3 Press (MODE) to select the play mode.

The mode changes as follows:

Resuming Mode t Album Mode t

Track Mode t Podcast Mode* t

Genre Mode t Playlist Mode t Artist

Mode

* May not appear depending on iPod setting.

4 Adjust the volume.

Press (OFF) to stop playback.

Removing the iPod

1 Stop the iPod playback.

2 Remove the iPod.

Caution for iPhone

When you connect an iPhone via USB, telephone

volume is controlled by iPhone itself. In order to avoid

sudden loud sound after a call, do not increase the

volume on the unit during a telephone call.

Notes

• Do not detach the front panel during playback of the

iPod, otherwise data may be damaged.

• This unit cannot recognize iPod via a USB hub.

Tips

• When the ignition key is turned to the ACC position,

and the unit is on, the iPod will be recharged.

• If the iPod is disconnected during playback, “NO

Device” appears in the display of the unit.

Resuming mode

When the iPod is connected to the dock

connector, the mode of this unit changes to

resuming mode and playback starts in the mode

set by the iPod.

In resuming mode, the following buttons do not

function.

– (1) (REP)

– (2) (SHUF)

Display items

To change display items, press (DSPL).

A Source (iPod) indication

B Clock

C Track name, Artist name, Album name

D EQ3 Parametric Preset/DM+ Advanced/

ZAPPIN*/Repeat*/Shuffle*

A Source (iPod) indication

B Clock

E Artist name, Album name, Track name, Track

number*, Total track number*, Elapsed

playing time*

* Hidden during Passenger control.

Tip

When album/podcast/genre/artist/playlist is changed,

its item number appears momentarily.

Note

Some letters stored in iPod may not be displayed

correctly.

A

B

DC

A

B

E

18

Setting the play mode

1 During playback, press (MODE).

The mode changes as follows:

Album Mode t Track Mode t

Podcast Mode* t Genre Mode t

Playlist Mode t Artist Mode

* May not appear depending on iPod setting.

Skipping albums, podcasts, genres,

playlists and artists

Repeat and shuffle play

1 During playback, press (1) (REP) or

(2) (SHUF) repeatedly until the

desired setting appears.

After 3 seconds, the setting is complete.

To return to normal play mode, select “Repeat

off” or “Shuffle off.”

Operating an iPod directly

— Passenger control

You can operate an iPod connected to the dock

connector directly.

1 During playback, press and hold

(MODE).

“Mode iPod” appears and you will be able to

operate the iPod directly.

To exit the passenger control

Press and hold (MODE).

Then “Mode Audio” will appear and the play

mode will change to “Resuming Mode.”

Notes

• The volume can be adjusted only by the unit.

• If this mode is canceled, the repeat setting will be

turned off.

To Press

Skip (3)/(4) (ALBUM –/+)

[press once for each]

Skip

continuously

(3)/(4) (ALBUM –/+)

[hold to desired point]

Select To play

Repeat Track track repeatedly.

Repeat Album album repeatedly.

Repeat Podcast podcast repeatedly.

Repeat Artist artist repeatedly.

Repeat Playlist playlist repeatedly.

Repeat Genre genre repeatedly.

Shuffle Album album in random order.

Shuffle Podcast podcast in random order.

Shuffle Artist artist in random order.

Shuffle Playlist playlist in random order.

Shuffle Genre genre in random order.

Shuffle Device device in random order.

19

Other functions

Changing the sound settings

Adjusting the sound

characteristics

1 Press the control dial.

2 Rotate the control dial until the

desired menu item appears, then

press it.

Depending on the setting, by rotating the

control dial again, further parameters can be

set.

3 Rotate the control dial to select the

setting, then press it.

4 Press (BACK).

The setting is complete and the display

returns to normal play/reception mode.

The following items can be set:

Customizing the equalizer curve

— EQ3 Parametric Tune

“Custom” of EQ3 Parametric Preset allows you

to make your own equalizer settings.

Select “Custom” of EQ3 Parametric Preset.

1 Select a source, then press and hold

the control dial.

2 Rotate the control dial to select “EQ3

Parametric Tune,” then press it.

3 Setting the equalizer curve.

You can adjust the equalizer center frequency,

volume level and bandwidth in each range

from “Low,” “Mid”, or “Hi.”

1 Rotate the control dial until the desired

menu item appears, then press it.

2 Rotate the control dial to select the

setting, then press it.

Selectable frequency in each range:

Low: 60 Hz or 100 Hz

Mid: 500 Hz or 1.0 kHz

Hi: 10.0 kHz or 12.5 kHz

Adjustable volume level: “+10 dB” –

“0 dB” – “–10 dB.”

EQ3 Parametric Preset

Selects an equalizer curve from 7 music types.

EQ3 Parametric Tune*

1

Custom equalizer settings.

Subwoofer Tune & LPF

Phase

Selects the phase (effective only when LPF is

on): “Normal,” “Reverse.”

FREQ

Selects the subwoofer cut-off frequency:

“80Hz,” “100Hz,” “120Hz,” “140Hz,” “160Hz,”

“OFF.”

Level

Adjusts the subwoofer volume: “+10dB” –

“0dB” – “–10dB.”

(“– ∞” is displayed at the lowest setting.)

HPF & Speaker Select

Speaker

Selects the Speaker: “All,” “Front”, or “Rear.”

FREQ

Selects the cut-off frequency: “OFF,” “80Hz,”

“100Hz,” “120Hz,” “140Hz,” “160Hz.”

DSO (Dynamic Soundstage Organizer)

Creates a more ambient sound field.

To select the DSO mode: “1,” “2,” “3,” or “off.”

The larger the number, the more enhanced the

effect.

Fader & Balance

Fader

Adjusts the relative level: “Front:15”– “Center”

– “Rear:15.”

Balance

Adjusts the sound balance: “Right:15”–

“Center” – “Left:15.”

AUX Level*

2

Adjusts the volume level for each connected

auxiliary equipment: “+18 dB” – “0 dB” – “–8

dB.”

This setting negates the need to adjust the

volume level between sources.

*1 Hidden when EQ3 Parametric Preset is set to “off.”

*2 When AUX source is activated.

continue to next page t

60Hz

MID HI

100Hz 500Hz 1.0kHz 10.0kHz 12.5kHz

LOW

-

10dB

+10dB

0dB

20

Selectable “Q” settings in each range:

Low: “0.5,” “1.0,” “1.5,” or “2.0”

Mid: “0.75,” “1.0,” “1.25,” or “1.5”

Hi: “0.75,” or “1.25”

You can control “Q” (the width of the range

of affected frequencies) with this function.

Repeat steps 1 and 2 to adjust other

frequency ranges.

4 Press (BACK) twice.

The setting is complete and the display

returns to normal play/reception mode.

To restore the factory-set equalizer curve, select

“Initialize” and “Yes” in step 3.

Tip

Other equalizer types are also adjustable.

Adjusting setup items — SET

1 Press and hold the control dial.

The setup display appears.

2 Rotate the control dial until the

desired menu item appears, then

press it.

3 Rotate the control dial to select the

setting, then press it.

The setting is complete.

4 Press (BACK).

The display returns to normal play/reception

mode.

Note

Displayed items will differ, depending on the source

and setting.

The following items can be set (follow the page

reference for details):

Setup

Display

Hz

Q=1.0 1.5 2.0 1.01.52.0

dB

Clock Adjust (page 6)

CT (Clock Time) (page 12, 13)

Beep

Activates the beep sound: “on,” “off.”

RM (Rotary Commander)

Changes the operative direction of the rotary

commander controls.

– “NORM”: to use the rotary commander in the

factory-set position.

– “REV”: when you mount the rotary

commander on the right side of the steering

column.

AUX Audio*

1

Activates the AUX source display: “on,” “off”

(page 21).

Auto Off

Shuts off automatically after a desired time

when the unit is turned off: “NO,” “30sec

(seconds),” “30min (minutes),” “60min

(minutes).”

Demo

(Demonstration)

Activates the demonstration: “on,” “off.”

Image

Sets various display images.

– “All”: to display all images.

– “Movie”: to display a movie.

– “SA 1 – 3, All”: to display the Spectrum

Analyzer.

– “Wall.P 1 – 3, All”: to display a wallpaper.

– “off”: to not display any image.

La page charge ...

Sony CDX-GT740UI Le manuel du propriétaire

Sony CDX-GT740UI Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents