GE GFD85ESSNWW Le manuel du propriétaire

49-3000206 Rev 8

06-23 GEA

GE is a trademark of the General Electric Company. Manufactured under trademark license.

DRYERS

SAFETY INFORMATION .........2

USING THE DRYER

WiFi Connect ........................ 4

Getting Started ...................... 4

Artificial Intelligence ...................6

Cycles ................................7

Settings ..............................8

Options ..............................9

Dryer Control – Bluetooth® Pairing ...... 11

Loading .............................12

CARE AND CLEANING ..........13

INSTALLATION

INSTRUCTIONS ..................14

Reversing The Door Swing (Optional) . . .32

Stacking (Optional) .................. 34

TROUBLESHOOTING TIPS ......38

LIMITED WARRANTY ...........41

CONSUMER SUPPORT ......... 42

OWNER’S MANUAL &

INSTALLATION

INSTRUCTIONS

Write the model and serial

numbers here:

Model # _________________

Serial # _________________

They are on the label on the front

of the dryer behind the door.

ENGLISH/FRANÇAIS/

ESPAÑOL

PFD95

GFD85

GFD65

GFD55

GFV55

249-3000206 Rev 8

WARNING

To reduce the risk of fire, explosion, electric shock, or injury to persons when using your

appliance, follow basic precautions, including the following:

Ŷ Read all instructions before using the appliance.

Ŷ

DO NOT dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite

or explode.

Ŷ DO NOT place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause a load to catch fire. To reduce the risk of fire due to

contaminated loads, the final part of the tumble dryer cycle occurs without heat (cool down period). Avoid

stopping a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread

out so that the heat is dissipated.

Ŷ DO NOT allow children to play on or in this appliance. Close supervision of children is necessary when this

appliance is used near children.

Ŷ Before the appliance is removed from service or discarded, remove the door to the drying compartment.

Ŷ DO NOT reach into the appliance if the drum is moving.

Ŷ DO NOT install or store this appliance where it will be exposed to the weather.

Ŷ DO NOT tamper with controls.

Ŷ DO NOT climb or stand on this unit.

Ŷ DO NOT repair or replace any part of this appliance or attempt any servicing unless specifically recommended

in the user-maintenance instructions or in published user-repair instructions that you understand and have the

skills to carry out.

Ŷ Follow all fabric care instructions and warnings to prevent melting of garments or damage to the appliance.

Ŷ DO NOT use fabric softeners or products to eliminate static unless recommended by the manufacturer of the

fabric softener or product.

Ŷ

DO NOT dry articles containing foam rubber or similarly textured rubber-like materials.

Ŷ Clean lint screen before or after each load.

Ŷ

DO NOT operate the dryer without the lint filter in place.

Ŷ DO NOT store combustible materials, gasoline or other flammable liquids near the dryer. Keep area around

the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust and dirt.

Ŷ The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.

Ŷ Unplug the appliance or turn off the circuit breaker before servicing. Pressing the Power or Start/Pause pad

DOES NOT disconnect power.

Ŷ DO NOT operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or

broken parts, including a damaged cord or plug.

Ŷ

DO NOT spray any type of aerosol into, on or near dryer at any time. DO NOT use any type of spray cleaner

when cleaning dryer interior. Hazardous fumes or electrical shock could occur.

Ŷ See “ELECTRICAL CONNECTION” located in the Installation Instructions for grounding instructions.

ŶDO NOT use replacement parts that have not been recommended by the manufacturer. (e.g. parts made at

home using a 3D printer).

READ AND SAVE THESE INSTRUCTIONS

Proper Disposal of your Appliance

Ŷ

Dispose of or recycle your appliance in accordance with Federal and Local Regulations. Contact your local

authorities for the environmentally safe disposal or recycling of your appliance.

Ŷ

Consider recycling options for your appliance packaging material.

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

49-3000206 Rev 8 3

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

SAFETY INFORMATION

Failure to follow safety warnings exactly could result in serious injury, death, or property

damage.

- DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of

this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

Ŷ

DO NOT try to light any appliance.

Ŷ

DO NOT touch any electrical switch; DO NOT use any phone in your building.

Ŷ

Clear the room, building, or area of any occupants.

Ŷ

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

Ŷ

If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

ADDITIONAL GAS DRYER WARNINGS

- Fire or Explosion Hazard

WARNING

READ AND SAVE THESE INSTRUCTIONS

449-3000206 Rev 8

Throughout this manual, features and appearance will vary from your model.

• If the screen is dark,

press the Power pad

to “wake up” the

display.

Step 2 Step 3 Step 4

Step 1

• Select a sensor dry cycle.

(Defaults are set for each dry

cycle. These default settings

can be changed. See the cycle

descriptions for more information.)

• Press the Start/

Pause pad.

• Clean lint filter

• Loosely add items.

• Close door.

NOTE: Dryer will not

start with door open.

To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY

INFORMATION before operating this appliance.

WARNING

OR

• Select TIMED DRY and set Time,

Temp and Level.

Ŷ

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Ŷ

DO NOT dry anything that has ever had anything

flammable on it (even after washing).

Ŷ

No washer can completely remove oil.

Ŷ

DO NOT dry anything that has ever had any type of oil

on it (including cooking oils).

Ŷ

Items containing foam, rubber, or plastic must be dried

on a clothesline.

Ŷ

Failure to do so can result in death, explosion, or fire.

- Fire Hazard

WARNING

Qu

i

c

k

Sta

r

t

:

WiFi Label Location

WiFi Connect (For customers in the United States only - on some models)

Your dryer is GE Appliances WiFi Connect enabled.

Visit geappliances.com/connect and enter your model number to

show you the proper steps to connect your appliance.

Please visit GEAppliances.com/connect to learn more about

connected appliance features, to learn what connected appliance

App’s will work with your smartphone.

WiFi Connectivity: For assistance with the appliance or the

ConnectPlus network connectivity, please call GE Appliances at

800.220.6899.

Getting started

USING THE DRYER

49-3000206 Rev 8 5

USING THE DRYER

Getting started

Features and appearance will vary.

CDA

B F FE

Model:

PFD95

CDA

B F FE

Model:

GFD85

CDA

B F FE

Model:

GFD65

CDA

B F FE

Models:

GFD55

GFV55

649-3000206 Rev 8

A

B

C

Power

Press to “wake up” the display. If the display is active, press to put the dryer into idle mode.

NOTE: Pressing Power does not disconnect the appliance from the power supply.

Start and Pause

Press Start to begin the cycle. NOTE: The door must be closed for the dryer to start the cycle. Pressing Start

again will pause the cycle, the Start light may blink and “Pause” will display.

To continue the cycle, press Start again.

Display and Status Lights

The display shows the approximate time remaining until the end of the cycle. On some models, the dryer cycle

status (Sense, Drying, Damp and Cool) will be shown.

In addition, the display will show:

Getting started

USING THE DRYER

(WiFi)

(on some models)

Will allow your appliance to communicate with your smartphone for remote appliance

monitoring control and notifications.

Controls The dryer is locked - will blink once if you press any pad or turn the cycle knob.

Check Filter The Check Filter light will stay on for 15 seconds after the cycle stops.

Check Vent The Check Vent light indicates an issue has been found due to reduced airflow from a possible

blocked or restricted vent. Checking and/or cleaning the vent system is recommended. See the,

“Check Vent” light is on in the Troubleshooting Tips section.

(on some models)

Your dryer is equipped with Artificial Intelligence capabilities. This indicator will illuminate when

Washer Link is active, My Settings are being implemented based on your usage habits and

suggested actions are available through the SmartHQ app.

(on some models)

This is a pairing feature for use with a compatible Bluetooth® enabled GE Appliances frontload

washer. To pair this dryer with the washer, please follow the steps outlined in the washer’s

Owner’s Manual. To engage or disengage Bluetooth®, open and close the door three times

within 10 seconds when the dryer is powered on but not actively running a cycle.

49-3000206 Rev 8 7

USING THE DRYER

Getting started

DDrying

Cycles

Sensor cycles automatically determine fabric dryness.

Timed cycles run for the selected time.

MIXED LOADS

For loads consisting of cottons and poly-blends.

COTTONS For cottons and most linens. NOTE: ENERGY STAR® models are tested on COTTONS cycle

with default settings (Temp setting on High, Level setting on Dry, and ecoDry default on).

TOWELS

(on some models) For most towels and linens.

BULKY

Bedding

For large coats, bed spreads, mattress covers, sleeping bags, and similar large/bulky items

such as blankets, comforters, jackets, and small rugs.

SANITIZE

(on some models) This option reduces certain types of bacteria including: Staphylococcus aureus, Pseudomonas

aeruginosa and Klebsiella pneumoniae. The anti-bacterial process occurs when high heat is

used during a portion of the drying cycle; cool down also will be longer to protect you from a

hot garment.

NOTE: Do not use this cycle on delicate fabrics.

WASHER

LINK (on

some models)

When selected (and if connected to a compatible washer through WiFi communication)

the dryer receives load information from the washer to automatically make cycle, dryness,

temperature and time recommendations to optimize drying.

ACTIVE

WEAR

(on some models)

Clothing worn for active sports exercise and some casual wear. Fabrics include new

technology finishes and stretch fibers such as Spandex. Also for clothing labeled Easy Care or

Perma Press: For wrinkle-free and permanent press items.

QUICK DRY For small loads that are needed in a hurry, such as sport or school uniforms. Can also be

used if the previous cycle left some items damp, such as collars or waistbands. NOTE: On

some models, the time remaining in the cycle will show counting down in the display.

DELICATES For delicate items, special-care fabrics and knits.

PERM PRESS

(on some models)

For wrinkle-free, permanent press and special sports items that need extra drying care.

AIR FLUFF

(on some models)

Provides 10 minutes of tumbling time with no heat. NOTE: On models with AIR FLUFF cycle,

select TIMED DRY and set Temp to No Heat.

DEWRINKLE

(on some models)

For removing wrinkles from items that are dry or slightly damp. This cycle is not recommended

for delicate fabrics.

STEAM

Dewrinkle

(on some models)

For use with larger loads than STEAM Refresh. Ideal for loads left in the dryer for an

extended time.

STEAM Dewrinkle is recommended for larger loads (9-13 garments).

NOTE: Steam cycles are not intended for use with towels.

Important - The temperature setting must be set to High and water must be turned on

before running the STEAM Dewrinkle cycle.

STEAM

Refresh

(on some models)

For slightly wrinkled dry garments. Significantly reduces wrinkles. After the STEAM Refresh

cycle, the unit will beep (if Sound is selected) and display “00.”

STEAM Refresh is recommended for small loads (3-5 garments).

NOTE: Steam cycles are not intended for use with towels.

NOTE: A single extremely light fabric item may need to have an additional item included in the

STEAM Refresh cycle to achieve optimum results.

Important - The temperature setting must be set to High and water must be turned on

before running the STEAM Refresh cycle.

STEAM

SANITIZE

(on some models)

This cycle will sanitize and remove set-in wrinkles from standard sized loads which are

damp from washing and/or rinsing. This cycle reduces certain types of bacteria including:

Staphylococcus aureus, Pseudomonas aeruginosa and Klebsiella pneumoniae. This anti-

bacterial process occurs when high heat is used during a portion of the drying cycle.

NOTE: Do not use this cycle on delicate fabrics.

Important - The temperature is set to HIGH and cannot be changed. Water must be

turned on for the Steam Sanitize cycle to function properly.

849-3000206 Rev 8

Getting started

USING THE DRYER

DDrying

Cycles

Sensor cycles automatically determine fabric dryness.

Timed cycles run for the selected time.

TIMED DRY

Use to set your own dry time. To use:

1. Turn cycle dial to TIMED DRY.

2. Increase the drying time by pressing the Time pad.

NOTE: This pad only increases the time. When max time is reached, pressing the pad again

will reset the counter to the lowest setting.

3. Select the Temp.

4. Close the door.

5. Press Start/Pause pad.

Settings

Individual settings for cycle minutes (Time), dryness level (Level) and temperature (Temp) can be set from the

minimum (lowest in column) to maximum (highest in column). In general, the higher up the column, the more

energy will be used. NOTE: The selected cycle set Time can be further adjusted, in one minute increments, by

pressing the More Time + and Less Time - pads.

E

Dryness Level - Selection only used for Sensor cycles. Timed cycles run for the selected time.

NOTE: Options for Dryness Levels vary by model. Refer to the control panel on your model or to the control

panels shown earlier in this manual.

Extra Dry Use for heavy-duty fabrics or items that should be very dry, such as towels.

More Dry Use for heavy-duty or mixed type fabrics.

Dry Use for a normal dryness level suitable for most loads. This is the preferred cycle for energy

savings.

Less Dry Use for lighter fabrics.

Damp For leaving items partially damp.

Temperature

High For regular to heavy cottons.

NOTE: STEAM Dewrinkle and STEAM Refresh require the High temperature setting.

Medium For synthetics, blends, delicates and items labeled permanent press.

Low For delicates, synthetics and items labeled tumble dry low.

Extra Low For lingerie and special-care fabrics.

No Heat For fluffing items without heat. For use only with the AIR FLUFF cycle.

49-3000206 Rev 8 9

Getting started

USING THE DRYER

FOptions

Reduce Static (on some models)

When selected, the dryer will spray a mist of water onto the load, at the end of the drying cycle, to reduce static.

This option is not available with BULKY, SANITIZE or STEAM cycles.

Damp Alert (Damp Alert/WiFi pad) (on some models)

This option causes the dryer to beep when clothes have dried to a damp level. Remove items that you wish

to hang dry. The Damp Alert will only beep when this option is selected (but the dry cycle will keep running).

Removing clothes and hanging them when they are damp, can reduce the need to iron some items.

Delay Dry

Press the Delay Dry pad to set the delay start time in 1 hour increments up to 24 hours, and then back to clear

(0 hours). After selecting the delay start time, press Start and the delay time will count down the time remaining

until the cycle starts. NOTE: To set the amount of delay time faster, you can press and hold the Delay Dry pad.

Delay Dry for WiFi Connected Dryers

You have two options to set Delay Dry using your smartphone.

Option 1: Follow Delay Dry instructions. You can use the GE Appliances Laundry App to adjust the amount of

time via your smartphone.

Option 2 - Remote Start: Set your dryer to “AP” using the Delay Dry pad. This allows you to use the GE Appliances

Laundry App via your smartphone to start your dryer remotely at the time of your choosing. If the dryer is set to

AP with no activity, it will start the dryer 24 hours later.

Air Fluff (on some models)

Provides 10 minutes of tumbling time with no heat. NOTE: On models without AIR FLUFF cycle, select TIMED

DRY and set Temp to No Heat.

Sound (on some models)

To change the loudness of the end of cycle signal and the press pad volume, press the Sound pad as many

WLPHVDVQHHGHGWRUHDFKWKHGHVLUHGYROXPH2QVRPHPRGHOVWKHUHDUHIRXUVRXQGOHYHOVLQFOXGLQJRႇRWKHU

PRGHOVKDYH2ႇ2QZLWKSUHVVDQGKROGIXQFWLRQ

NOTE:

• Remove garments promptly at the sound of signal. Place clothes on hangers so wrinkles will not set in.

• Use the Sound especially when drying fabrics like polyester, knits and permanent press. These fabrics should

be removed so wrinkles will not set in.

Wrinkle Care

Use this option to minimize the wrinkles in clothes. It provides 1 hour of no-heat tumbling after the clothes are

dry. If you are using the cycle Sound and you select the Wrinkle Care option, a signal will sound at the end of

the drying time and several times during the Wrinkle Care cycle. This will remind you that it is time to remove

the clothes.

More Time + / Less Time -

The selected cycle set Time can be further adjusted, in one minute increments, by pressing the More Time +

and Less Time - pads.

ecoDry

Available for BULKY, TOWELS, COTTONS, MIXED LOADS, ACTIVE WEAR and DELICATES. When the

ecoDry pad is pressed, cycle settings change to reduce the total energy consumption of the selected sensor

cycle. NOTE: Cycle times will change when ecoDry is selected. The ecoDry option will default to on for

COTTONS. For optimal energy savings, turn ecoDry on. For optimal drying times, turn ecoDry off.

NOTE: Energy savings will vary across loads and cycles.

10 49-3000206 Rev 8

Getting started

USING THE DRYER

FOptions (cont.)

Light (on some models)

The drum light will turn on if the Light pad is pressed or the door is opened. It will turn off when the door is shut,

the Light pad is pressed again or after 5 minutes if the door is left open.

Small Load (on some models)

Select to use for a small load with any sensor cycle (except SANITIZE).

My Settings (on some models)

As the cycle selector knob is turned, the Time (timed dry), Level (dryness level) and Temp (temperature)

settings change to automatic pre-set default settings. If you desire a different setting, press the appropriate

pad(s). Then press and hold the My Settings pad for 3 seconds and the dryer will “remember” these settings

for that Knob Selection. In the future, when you turn the selector knob to that cycle, your settings will be

automatically recalled.

NOTE: Signal sound cannot be set for My Settings.

NOTE: On models equipped with AI (Artificial Intelligence), My Settings may be set automatically based on

your usage habits. If you would like to reset this, press and hold MY Settings to clear the memory.

Control Lock

You can lock the controls to prevent any selections from being made. Or you can lock the controls after you

have started a cycle. Children cannot accidentally start the dryer by touching pads with this option selected.

To lock/unlock the dryer controls, press and hold the Light pad for 3 seconds. The control lock icon will flash

while locking/unlocking, stay on when locked, and turn off when unlocked.

NOTE: The Power pad can still be used when the machine is locked.

WiFi (Damp Alert/WiFi pad)

Press and hold the Damp Alert/WiFi pad for 3 seconds to activate.

49-3000206 Rev 8 11

Getting started

USING THE DRYER

Dryer Control – Bluetooth® Pairing

(on some models)

1. Power on both the washer and the dryer but do not start any

cycles.

2. Press and hold the Tumble Care button on the

washer for 5 seconds until the Bluetooth® LED ( )

starts to flash and you hear an audible tone.

3. Open and close the dryer door 3 times within 10 seconds to

make it discoverable to the washer.

4. The washer will attempt to discover the dryer, the Bluetooth®

icon will flash and both displays will blink “ - - - ”.

5. The Bluetooth® icon on the washer should illuminate solid

signifying that the machines are now paired. The display on

the washer will display “bt” for 3 seconds.

6. If the Bluetooth® units fail to pair, repeat above steps 1-5.

7. To unpair the machines, press and hold the Tumble

Care button for 10 seconds or open and close the

dryer door 3 times within 10 seconds.

Open and close

dryer door

3 times within

10 seconds

1. Power on the washer.

2. Press and hold the Dryer Control button on the

washer for 3 seconds to power on the dryer.

3. The dryer’s cycle selection will flash to display the

recommended sensor cycle that pairs to the last completed

washer cycle as the washer display reads “drY”.

4. To use this cycle, press the Dryer Control button to

start the dryer. The dryer can be paused by opening

its door or pressing the Dryer Control button. To restart

the dryer with its door closed, press the Dryer Control

button again.

5. To select Timed Dry instead of the sensor dry cycle, press the

Timed Dry button on the washer while the display says “drY”.

Repeated presses of this button will step through preset Timed

Dry times (default is 40 minutes).

6. Once you’ve selected the Timed Dry cycle’s duration,

press the Dryer Control button within 10 seconds to

start the dryer.

Washer

Dryer

NOTE: Your dryer’s control panel is fully

functional even when you are using Dryer

Control through the washer.

Powering off the washer will not power off

the dryer when a dry cycle is in progress.

Scan for

instruction

How to use the Dryer Control Feature (on some models)

12 49-3000206 Rev 8

Drying Rack (Available as an option)

A handy drying rack may be used for drying delicate items such as washable sweaters.

To install the drying rack, place the rack all the way into the dryer drum and fit its feet down and securely into place

in the dryer.

NOTES:

• The drying rack must be used with the TIMED DRY cycle. Use with sensor cycles may

result in damp items or extended cycle times.

• Do not use this drying rack when there are other clothes in the dryer.

• If your model did not come with a drying rack, order WE02X29449 on-line at

GEApplianceparts.com, 24 hours a day or by phone at 877.959.8688 during normal

business hours.

Always follow fabric manufacturer’s care label when laundering.

As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer. Try also to sort

items according to size. For example, do not dry a sheet with socks or other small items.

Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. Bounce®

Fabric Conditioner Dryer Sheets have been approved for use in this dryer when used in accordance with the

manufacturer’s instructions.

Do not overload. This wastes energy and causes wrinkling.

Ŷ

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Ŷ

DO NOT dry anything that has ever had anything

flammable on it (even after washing).

Ŷ

No washer can completely remove oil.

Ŷ

DO NOT dry anything that has ever had any type of oil

on it (including cooking oils).

Ŷ

Items containing foam, rubber, or plastic must be dried

on a clothesline.

Ŷ

Failure to do so can result in death, explosion, or fire.

Sorting and Loading Hints

- Fire Hazard

WARNING

Loading

USING THE DRYER

49-3000206 Rev 8 13

Lint Filter

Clean the lint filter before each use.

Remove by pulling straight up. Run your fingers across the filter. A waxy buildup may form

on the lint filter from using dryer added fabric softener sheets.

To remove this buildup, wash the lint screen in warm, soapy water. Dry thoroughly and

replace.

Vacuum the lint from the dryer lint filter area if you notice a change in dryer performance.

NEVER OPERATE THE DRYER WITHOUT ITS FILTER IN PLACE.

CARE AND CLEANING

Care and cleaning

Exterior

Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged

by some laundry pretreatment soil and stain remover products. Apply these products away from the dryer. The fabric

may then be washed and dried normally. Damage to your dryer caused by these products is not covered by your

warranty.

Stainless Steel (on GFD85 & PFD95 models only)

The stainless steel used to make the dryer drum provides the highest reliability available in a GE Appliances dryer.

If the dryer drum should be scratched or dented during normal use, the drum will not rust or corrode. These surface

blemishes will not affect the function or durability of the drum.

To clean stainless steel surfaces use a damp cloth with a mild, non-abrasive cleaner suitable for stainless steel

surfaces. Remove the cleaner residue and then dry with a clean cloth.

Interior and Duct

The interior of the appliance and exhaust duct should be cleaned once a year by qualified service personnel.

The Exhaust Duct: Inspect and clean the exhaust ducting at least once a year to prevent clogging. A partially clogged

exhaust can lengthen the drying time.

Follow these steps:

1 Turn off electrical supply by disconnecting the plug from the wall socket.

2 Disconnect the duct from the dryer.

3 Vacuum the duct with the hose attachment and reconnect the duct.

The Exhaust Hood: Check with a mirror that the inside flaps of the hood move freely when operating. Make sure that there

is no wildlife (birds, insects, etc.) nesting inside the duct or hood.

Alcosta Aluminized Steel (on all other models)

The steel used to make the dryer drum has an aluminized coating on its surface to prevent it from rusting or

corroding. Any surface blemishes will not affect the function or durability of the drum.

To clean the Alcosta surface use a damp cloth with a mild, non-abrasive cleaner suitable for stainless steel surfaces.

Remove the cleaner residue and then dry with a clean cloth.

Drum Light (on some models)

The drum light is an LED light. Replacement must be done by a qualified technician.

14 49-3000206 Rev 8

Installation

Dryer

Instructions

If you have any questions, call GE Appliances at 800.GE.CARES

(800.432.2737) or visit our Website at: GEAppliances.com

In Canada, call 800.561.3344 or visit www.GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT – Save these instructions for

local electrical inspector’s use.

• IMPORTANT – Observe all governing

codes and ordinances.

• Install the clothes dryer according to the

manufacturer’s instructions and local codes.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Clothes dryer installation must be performed by a

qualified installer.

• This dryer must be exhausted to the outdoors.

• Before the old dryer is removed from service or

discarded, remove the dryer door.

• Service information and the wiring diagram are

located in the control console.

• Do not allow children on or in the appliance. Close

supervision of children is necessary when the

appliance is used near children.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

• Install the dryer where the temperature is above

50°F for satisfactory operation of the dryer control

system.

• Remove and discard existing plastic or metal foil

duct and replace with UL-listed duct.

- Risk of Fire

• Clothes dryer installation must be performed by a

qualified installer.

• Install the clothes dryer according to these

instructions and local codes.

• DO NOT install a clothes dryer with flexible plastic

venting materials. If flexible metal (semi-rigid or

foil-type) duct is installed, it must be UL-listed and

installed in accordance with the instructions found

in “Connecting the Dryer to House Vent” later in

this manual. Flexible venting materials are known

to collapse, be easily crushed and trap lint. These

conditions will obstruct dryer airflow and increase

the risk of fire.

• DO NOT install or store this appliance in any

location where it could be exposed to water or

weather.

• To reduce the risk of severe injury or death, follow

all installation instructions.

• Save these instructions. (Installers: Be sure to

leave these instructions with the customer.)

If you are planning to stack the washer and dryer, order

Stacking Kit number GFA28KITN to be used for this

dryer. Kit sold separately.

WARNING

In the Commonwealth of Massachusetts,

the following installation instructions apply:

• Installation must be performed by a qualified or

licensed contractor, plumber, or gasfitter qualified

or licensed by the State.

• If using a ball valve, it shall be a T-handle type.

• A flexible gas connector, when used, must not

exceed 4 feet (1.2 m).

FOR GAS DRYERS ONLY

49-3000206 Rev 8 15

*NOTE: With leveling legs retracted: 39-3/4 (101 cm).

With leveling legs fully extended: 40-5/8 (103.1 cm).

With Optional Pedestal: 55-1/2” (141 cm) Min. - 56-5/8” (143.8 cm) Max.

Stacked: 79-1/8” (201 cm).

Installation Instructions

Tilt the dryer sideways and remove the foam shipping pads by pulling at the sides and breaking them

away from the dryer legs. Be sure to remove all of the foam pieces around the legs.

Remove the bag containing the literature. Consider recycling options for your appliance packaging material.

UNPACKING YOUR DRYER

DRYER

DIMENSIONS

Side View

31-3/8” (79.7 cm)

54-1/4” (137.8 cm)

Front View

28”

(71.2 cm)

*39-3/4”

(101 cm)

GE Appliances strongly recommends the use of factory

specified parts. These hoses are manufactured and tested

to meet GE Appliances specifications.

GE Appliances strongly recommends the use of new water

supply hoses. Hoses degrade over time and need to be

replaced every 5

years to reduce the risk of hose failures

and water damage.

Parts and Accessories

Order on-line at GEApplianceparts.com, 24 hours a day

or by phone at 877.959.8688 during normal business hours.

STEAM WATER HOSES (for steam dryer models only):

ACCESSORIES:

Order on-line at GEApplianceparts.com, 24 hours a day or

by phone at 877.959.8688 during normal business hours.

Part Number Accessory

GFA28KITN Stacking Kit for Dryer over Washer

GFA28DSVN

(WE16X29317) Dryer Venting Kit

PM08X10085

Flexible Metal Dryer Transition Duct

WE02X29449

Clothes Dryer Drying Rack

GFP1528SNWW

White Pedestal

GFP1528PNSN

Satin Nickel Pedestal

GFP1528PNRS Royal Sapphire Pedestal

GFP1528PNDG Diamond Gray Pedestal

GFP1528PTDS Black Slate Pedestal

Part Number Accessory

WE25X20060

Complete Kit (hoses, Y-adapter, washers)

or

WE49X25794

Kit (Short hose, Y-adapter, washers)

and

WE1M847 Long Hose

OR SEPARATELY

WE1M847 Long Hose and

WE1M848 Short Hose

Part Number Accessory

GFR0728SNWW

White Riser

GFR0728PNSN

Satin Nickel Riser

GFR0728PNRS Royal Sapphire Riser

GFR0728PNDG

Diamond Gray Riser

GFR0728PTDS Black Slate Riser

16 49-3000206 Rev 8

Installation Instructions

MOBILE OR MANUFACTURED

HOME INSTALLATION

• Installation MUST conform to the

MANUFACTURED HOME CONSTRUCTION

AND SAFETY STANDARD, TITLE 24, PART

3280 or STANDARD FOR MOBILE HOMES

CAN/CSA-Z240 MH, or, when such standards

are not applicable, with AMERICAN NATIONAL

STANDARD FOR MOBILE HOME, ANSI/NFPA

NO. 501B.

• The dryer MUST be vented to the outdoors.

• The exhaust vent MUST be securely fastened to a

non-combustible portion of the mobile home.

• The vent MUST NOT be terminated beneath a

mobile or manufactured home.

• The vent duct material MUST BE METAL.

• KIT 14-D346-33 MUST be used to attach the dryer

securely to the structure.

• The vent MUST NOT be connected to any other

duct, vent or chimney.

• DO NOT use sheet metal screws or other

fastening devices which extend into the interior of

the exhaust vent.

• Provide an opening with a free area of at least 25

square inches (63 cm2) for introduction of outside

air into the dryer room.

• See the sections for electrical connection information.

REQUIREMENTS FOR ALCOVE OR

CLOSET INSTALLATION

Keep flammable materials and vapors, such as gasoline,

away from dryer.

Place dryer at least 18” (46 cm) above the floor for a

garage installation.

Failure to do so can result in death, explosion, or fire.

• The dryer MUST be vented to the outdoors.

• Minimum clearance between dryer cabinet and

adjacent walls or other surfaces is:

0” (0 cm) either side*

0” (0 cm) front

0” (0 cm) rear

0”

(0 cm) top

* For improved performance, a 1/2” (12.7 mm)

clearance is suggested on each side.

• The rear of the dryer should face a wall.

• Consideration must be given to provide adequate

clearance for installation and service.

• Closet doors must be louvered or otherwise

ventilated and have at least 60 square inches (387

cm2) of open area. If the closet contains both a

washer and a dryer, doors must contain a minimum

of 120 square inches (774 cm2) of open area.

NOTE: WHEN THE EXHAUST DUCT IS LOCATED AT

THE REAR OF THE DRYER, THE CONFIGURATION

OF THE DUCTING MAY REQUIRE GREATER

CLEARANCE.

Gas Dryers Only:

• No other fuel burning appliance shall be installed in

the same closet as a gas dryer.

• The dryer must be disconnected from the gas

supply piping during pressure testing at pressures

greater than 1/2 psi (3.5 kPa).

• A 1/8” (3.2 mm) NPT minimum plugged tapping,

accessible for test gauge connection, must be

installed immediately upstream of the gas supply

connection to the dryer.

MINIMUM CLEARANCE OTHER

THAN ALCOVE OR CLOSET

INSTALLATION

Minimum clearance to combustible surfaces and for

air opening are: 0” (0 cm) both sides*, 0” (0 cm) rear

and 0” (0 cm) top.

* For improved performance, a 1/2” (12.7 mm)

clearance is suggested on each side.

The rear of the dryer should face a wall.

Consideration must be given to provide adequate

clearance for installation and service.

- Explosion Hazard

WARNING

49-3000206 Rev 8 17

Installation Instructions

CONNECTING INLET HOSES (for steam dryer models only)

CONNECTING INLET HOSES (cont.)

7. Using pliers, tighten all the couplings with an

additional two–thirds turn.

NOTE: Do not overtighten. Damage to the

couplings may result.

8. Turn the water faucet on.

9. Check for leaks around the ‘’Y’’ connector,

faucet and hose couplings.

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed

within 42 in. (107 cm) of your washer’s water

inlet. The faucets MUST be 3/4” (19.1 mm)

garden hose-type so inlet hoses can be

connected. Water pressure MUST be between

10 and 120 pounds per square inch. Your

water department can advise you of your water

pressure.

NOTE: A water softener is recommended

to reduce buildup of scale inside the steam

generator if the home water supply is very hard.

To produce steam, the dryer must connect to

the cold water supply. Since the washer must

also connect to the cold water, a “Y” connector

is inserted to allow both inlet hoses to make that

connection at the same time.

NOTE: Use new inlet hoses; never use old

hoses.

1. Turn the cold water faucet off. Remove the

washer inlet hose from the washer fill valve

connector (cold).

2. Ensure the rubber flat washer is in place and

attach one female coupling of the short hose

provided onto the washer fill valve connector.

Tighten by hand until firmly seated.

3. Attach one male end of the “Y” connector to

the other female coupling of the short hose.

Ensure the rubber flat washer is in place.

Tighten by hand until firmly seated.

4. Insert the filter screen in the coupling of the

washer’s inlet hose. If a rubber flat washer is

already in place remove it before installing the

filter screen. Attach this coupling to one male

end of the ‘’Y’’ connector. Tighten by hand until

firmly seated.

5. Ensure the rubber flat washer is in place

and attach a 4 ft. (1.2 m) to 6 ft. (1.8 m) long

water inlet hose (may need to be purchased

separately) to one male end of the ‘’Y’’

connector. Tighten by hand until firmly seated.

6. Ensure the rubber flat washer is in place and

attach the other end of the dryer’s long inlet

hose to the fill valve connector at the bottom

of the dryer back panel. Tighten by hand until

firmly seated.

CONNECTING INLET HOSES

18 49-3000206 Rev 8

Installation Instructions

CONNECTING A GAS DRYER (skip for electric dryers)

• Before beginning the installation, turn off the circuit

breaker(s) or remove the dryer’s circuit fuse(s) at

the electrical box. Be sure the dryer

cord is unplugged from the wall.

• Turn the dryer’s gas shut-off valve in the supply line

to the OFF position.

• Disconnect and discard old flexible gas connector

and ducting material.

Shut-off

Valve

MATERIALS YOU WILL NEED

Ŷ

Ŷ 4” (10.2 cm) dia. metal

elbow

Ŷ

Ŷ Pipe compound or

PTFE tape

Ŷ

Ŷ Flexible gas line

connector

Ŷ

Ŷ 4” (10.2 cm) Duct

clamps (2) or 4” (10.2

cm) spring clamps (2)

Ŷ

Ŷ Safety glasses

Ŷ

Ŷ 4” (10.2 cm) dia. metal

duct (recommended)

Ŷ

Ŷ Gloves

Ŷ

Ŷ Soap solution for

leak detection

Ŷ

Ŷ Aluminum foil tape

Ŷ

Ŷ Gas pipe adapters (2),

elbow and pipe plug

TOOLS YOU WILL NEED

Ŷ

Ŷ 10” (25.40 cm)

Adjustable wrenches (2)

Ŷ

Ŷ 8” (20.32 cm)

Pipe wrench

Ŷ

Ŷ Flat-blade

screwdriver

Ŷ

Ŷ Level

Ŷ

Ŷ Slip-joint pliers

Ŷ

Ŷ 4” (10.2 cm) dia.,

UL-listed flexible

metal duct (if needed)

Ŷ

Ŷ Access Panel

GFA28DSVN Kit

(All parts included in

this Kit or parts may be

purchased separately)

Ŷ

Ŷ Exhaust hood

49-3000206 Rev 8 19

Installation Instructions

GAS REQUIREMENTS

DRYER GAS SUPPLY CONNECTION

GAS SUPPLY

• A 1/8” (3.2 mm) National Pipe Taper thread

plugged tapping, accessible for test gauge

connection, must be installed immediately

upstream of the gas supply connection to the

dryer. Contact your local gas utility should you

have questions on the installation of the plugged

tapping.

• Supply line is to be 1/2” (12.7 mm) rigid pipe and

equipped with an accessible shutoff within 6 feet

(1.8 m) of, and in the same room with, the dryer.

• Use pipe thread compound appropriate for

natural or LP gas or use PTFE tape.

• Connect flexible metal connector to dryer and

gas supply.

ADJUSTING FOR ELEVATION

• Gas clothes dryers input ratings are based on

sea level operation and need not be adjusted for

operation at or below 2000 ft. (610 m) elevation.

For operation at elevations above 2000 ft. (610 m),

input ratings should be reduced at a rate of 4

percent for each 1000 ft. (305 m) above sea level.

• Installation must conform to local codes and

ordinances or, in their absence, the NATIONAL

FUEL GAS CODE, ANSI Z223.

You must use with this dryer a flexible metal connector

(listed connector ANSI Z21.24 / CSA 6.10). The length

of the connect shall not exceed 4 ft. (1.2 m).

• Use a new CSA International approved flexible

gas supply line. Never reuse old flexible

connectors.

• Install an individual manual shut-off valve

within 6ft. of the dryer in accordance with the

National Fuel Gas Code, ANSI Z223.1/NFPA

54.

• Securely tighten all gas connections.

• If connected to LP gas, have a qualified

person make sure gas pressure DOES NOT

exceed 13” (33 cm) water column.

• Examples of a qualified person include:

licensed heating personnel, authorized gas

company personnel, and authorized service

personnel.

• Failure to do so can result in death,

explosion, or fire.

• The installation must conform with local

codes, or in the absence of local codes, with

the National Fuel Gas Code, ANSI Z223.1/

NFPA 54, or the Natural Gas and Propane

Installation Code, CSA B149.1.

FOR USE WITH NATURAL GAS ONLY

Dryer as produced by manufacturer is to be used

only with a natural gas supply. A manufacturer-

supplied conversion kit is required to convert this

dryer for propane gas supply. Use propane

gas

conversion kit WE25M87

. Conversion must be

made by properly trained and qualified personnel

in accordance with local codes and ordinances.

- Fire Hazard

WARNING

- Explosion Hazard

WARNING

CONNECTING A GAS DRYER (cont.)

NOTE: Add to vertical dimension the

GLVWDQFHEHWZHHQFDELQHWERWWRPWRÀRRU

3/8” (9.6 mm) NPT

MALE THREAD

GAS SUPPLY

1-5/8” (4.16 cm)

5-3/4”

(14.57 cm)

20 49-3000206 Rev 8

Installation Instructions

CONNECTING A GAS DRYER (cont.)

Install a 1/8” (3.2 mm) NPT plugged tapping

to the dryer gas line shut-off valve for

checking gas inlet pressure.

Install a flare union adapter to the plugged

tapping.

NOTE: Apply pipe compound or PTFE tape

to the threads of the adapter and plugged

tapping.

Attach the flexible metal gas line connector to

the adapter.

B

Tighten the flexible gas line connection, using

two adjustable wrenches.

C

D

Tighten all connections, using two adjustable

wrenches. Do not overtighten.

E

CONNECTING THE DRYER TO

THE GAS SUPPLY (cont.)

Open the gas shut-off valve.

F

Apply pipe compound

or PTFE tape to all

male threads.

Shut-Off

Valve

Plugged

Tapping

CONNECTING THE DRYER TO

THE GAS SUPPLY

Install a female 3/8” (9.6 mm) NPT elbow at

the end of the dryer gas inlet.

Install a 3/8” (9.6 mm) flare union adapter to

the female elbow.

IMPORTANT: Use a pipe wrench to securely

hold on to the end of the dryer gas inlet to

prevent twisting the inlet.

NOTE: Apply pipe compound or PTFE tape to

the threads of the adapter and dryer gas inlet.

A

Elbow

Adapter

Items not supplied

Adapter

1/8” (3.2 mm)

NPT Pipe Plug

for Checking

Gas Inlet

Pressure

Shut-Off Valve

Pipe size at

least 1/2” (12.7

mm)

3/8” (9.6 mm)

NPT

New Metal

Flexible Gas

Line Connector

Apply pipe compound to the

adapter and dryer gas inlet.

La page charge ...

GE GFD85ESSNWW Le manuel du propriétaire

GE GFD85ESSNWW Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents