GE Profile 7.4 Cu Ft Le manuel du propriétaire

Marque: GE Profile

Modèle: 7.4 Cu Ft

Taper: Le manuel du propriétaire

GE is a trademark of the General Electric Company. Manufactured under trademark license.

249-3000244 Rev 5

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-3000244 Rev 5 3

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

SAFETY INFORMATION

To reduce the risk of fire, explosion, electric shock, or injury to persons when using your

appliance, follow basic precautions, including the following:

Read all instructions before using the appliance.

DO NOT

dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite

or explode.

DO NOT place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause a load to catch fire. To reduce the risk of fire due to

contaminated loads, the final part of the tumble dryer cycle occurs without heat (cool down period). Avoid

stopping a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread

out so that the heat is dissipated.

DO NOT allow children to play on or in this appliance. Close supervision of children is necessary when this

appliance is used near children.

Before the appliance is removed from service or discarded, remove the door to the drying compartment.

DO NOT reach into the appliance if the drum is moving.

DO NOT install or store this appliance where it will be exposed to the weather.

DO NOT tamper with controls.

DO NOT climb or stand on this unit.

DO NOT repair or replace any part of this appliance or attempt any servicing unless specifically recommended

in the user-maintenance instructions or in published user-repair instructions that you understand and have the

skills to carry out.

• Follow all fabric care instructions and warnings to prevent melting of garments or damage to the appliance.

DO NOT use fabric softeners or products to eliminate static unless recommended by the manufacturer of the

fabric softener or product.

DO NOT dry articles containing foam rubber or similarly textured rubber-like materials.

Clean lint screen before or after each load.

DO NOT operate the dryer without the lint filter in place.

DO NOT store combustible materials, gasoline or other flammable liquids near the dryer. Keep area around

the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust and dirt.

The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.

Unplug the appliance or turn off the circuit breaker before servicing. Pressing the Power or Start/Pause

button DOES NOT disconnect power.

DO NOT operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or

broken parts, including a damaged cord or plug.

DO NOT spray any type of aerosol into, on or near dryer at any time. DO NOT use any type of spray cleaner

when cleaning dryer interior. Hazardous fumes or electrical shock could occur.

See “ELECTRICAL CONNECTION” located in the Installation Instructions for grounding instructions.

READ AND SAVE THESE INSTRUCTIONS

Proper Disposal of your Appliance

Dispose of or recycle your appliance in accordance with Federal and Local Regulations. Contact your local

authorities for the environmentally safe disposal or recycling of your appliance.

Consider recycling options for your appliance packaging material.

449-3000244 Rev 5

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

Failure to follow safety warnings exactly could result in serious injury, death, or property

damage.

- DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of

this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

DO NOT try to light any appliance.

DO NOT touch any electrical switch; DO NOT use any phone in your building.

Clear the room, building, or area of any occupants.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

ADDITIONAL GAS DRYER WARNINGS

- Fire or Explosion Hazard

49-3000244 Rev 5 5

Throughout this manual, features and appearance may vary from your model.

• If the screen is dark,

press the Power

button to “wake up”

the display.

Step 2 Step 3 Step 4Step 1

• Select a dry cycle. (Defaults are set

for each dry cycle. These default

settings can be changed. See the cycle

descriptions for more information.)

• Press the Start/

Pause button.

• Clean lint filter

• Loosely add items.

• Close door.

NOTE: Dryer will not

start with door open.

Using the dryer

To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY

INFORMATION before operating this appliance.

Appliance communication

WiFi Connect (For customers in the United States only - on some models)

Depending on the model, your dryer is either GE Appliances

WiFi Connect enabled, or compatible using the optional

GE Appliances U+ Connect module.

If enabled: Visit GEAppliances.com/connect and enter

your model number to show you the proper steps to

connect your appliance.

To turn off (disable) your appliance’s WiFi and Voice

Assistant feature (on some models), press and hold the

Temp button for 3 seconds. You will see that the WiFi

symbol will turn off. This will return the appliance to its

as-shipped, factory default configuration.

If compatible: To connect this appliance to the

internet you will need to purchase a GE Appliances

U+ Connect module and attach it to your appliance

through the communication port. The GE Appliances

U+ Connect module will allow your appliance to

communicate with your smartphone for remote

appliance monitoring, control and notifications.

WiFi Connectivity: For assistance with the appliance

or the GE Appliances U+ Connect network connectivity,

please call GE Appliances Connected Home Support at

800.220.6899.

Please visit GEAppliances.com/connect to learn

more about connected appliance features, to learn

what connected appliance Apps will work with your

smartphone and to learn where you can purchase a

U+ Connect module.

The U+ Connect module has the FCC/IC ID located

on the back of the module.

Part Number Accessory

PBX23W00Y0 WiFi U+ Connect module

Keep flammable materials and vapors, such as

gasoline, away from dryer.

DO NOT dry anything that has ever had anything

flammable on it (even after washing).

No washer can completely remove oil.

DO NOT dry anything that has ever had any type of oil

on it (including cooking oils).

Items containing foam, rubber, or plastic must be dried

on a clothesline.

Failure to do so can result in death, explosion, or fire.

- Fire Hazard

649-3000244 Rev 5

CDisplay and Status Lights

The display shows the approximate time remaining until the end of the cycle.

In addition, this display will show the dryer status:

Features and

appearance

will vary.

Using the dryer

Pause

(on some models) The Start/Pause light will flash and the message “Pause” will show in the display when the

dryer’s cycle is paused. The cycle may be re-started by pressing the Start button.

WiFi

(on some models)

Will allow your appliance to communicate with your smartphone for remote appliance

monitoring control and notifications.

Controls The dryer is locked - will blink once if you press any button or turn the cycle knob.

Sensing Indicates the dryer is sensing the level of dampness to determine estimated cycle time

remaining.

Clean Lint Filter The Clean Lint Filter light will stay on for 15 seconds after the cycle stops.

Vent Blocked

(on some models) The Vent Blocked light indicates an issue has been found due to reduced airflow from a

possible blocked or restricted vent. Checking and/or cleaning the vent system is recommended.

See the, “Vent Blocked” light is on in the Troubleshooting Tips section.

Sensing Garments need additional time to be dried.

Drying Clothes dryer is removing moisture.

Cooling Air fluff cooling time after drying process.

Done Cycle has been completed and it will display the legend “END”.

Vent + Test Venting system diagnostic test.

Tank Low

(on some models)

The Fabric Refresh tank only has liquid for two more loads. Refill the tank.

Empty

(on some models)

The Fabric Refresh tank is empty and must be refilled before running another cycle with

Fabric Refresh enabled.

Less/Auto/More

(on some models)

Fabric Refresh is enabled and at the displayed disposing level.

Power

Press to “wake up” the display. If the display is active, press to put the dryer into idle mode.

NOTE: Pressing Power does not disconnect the appliance from the power supply.

Start and Pause

Press Start to begin the cycle. NOTE: The door must be closed for the dryer to start the cycle. Pressing Start

again will pause the cycle, the Start light will blink and “Pause” will display.

To continue the cycle, press Start again.

A E GC

FH I JDKMLB

ML JGB

A E GC

ML FGB

A E

49-3000244 Rev 5 7

USING THE DRYER

Using the dryer

DControl Lock

You can lock the controls to prevent any selections from being made. Or you can lock the controls after you have

started a cycle. Children cannot accidentally start the dryer by touching buttons with this option selected.

To lock/unlock the dryer controls, press and hold the ecoDry button for 3 seconds. The control lock icon will

flash while locking/unlocking, stay on when locked, and turn off when unlocked.

NOTE: The Power button can still be used when the machine is locked.

EDrying

Cycles

Sensor cycles automatically determine fabric dryness.

Timed cycles run for the selected time.

SANITIZE This option reduces certain types of bacteria including: Staphylococcus aureus, Pseudomonas

aeruginosa and Klebsiella pneumoniae. The anti-bacterial process occurs when high heat is

used

during a portion of the drying cycle; cool down also will be longer to protect you from a hot

garment.

NOTE: Do not use this cycle on delicate fabrics.

BULKY For large coats, bed spreads, mattress covers, sleeping bags, and similar large/bulky items such

as blankets, comforters, jackets, and small rugs.

TOWELS/

Sheets For most towels and linens.

NORMAL/

Cottons For cottons and most linens. NOTE: ENERGY STAR® models are tested on NORMAL/

Cottons with default settings (Dry level, Hot temperature and ecoDry).

MIXED LOAD

For loads consisting of cottons and poly-blends.

DOWNLOADED

Option with additional cycles available through your GE Appliances SmartHQ App:

Casual (Default): Wrinkle care and permanent press items.

Active Wear: Special sport items that need extra drying care.

Warm Up: Provides 10 minutes of heating to warm up clothes.

STEAM Dewrinkle: For use with larger loads than 9-13 garments. Ideal for loads left in the

dryer for an extended time.

DELICATES For delicate items, special-care fabrics and knits.

QUICK DRY For small loads that are needed in a hurry, such as sport or school uniforms. Can also be used if the

previous cycle left some items damp, such as collars or waistbands. NOTE: On some models, the

time remaining in the cycle will show counting down in the display.

JEANS For jeans.

TIMED DRY

Set the Cycle Selector at the desired drying time.

WARM UP Provides 10 minutes of warming time to warm up clothes.

AIR FLUFF Provides 10 minutes of tumbling time with no heat. NOTE: On models without AIR FLUFF

cycle, select TIMED DRY and set Temp to No Heat.

STEAM

(on some models) A cycle with two options available through the GE Appliances SmartHQ App:

STEAM Refresh (Default): For slightly wrinkled dry garments. Significantly reduces

wrinkles. It’s recommended for small loads (3-5 garments).

NOTE: Steam cycles are not intended for use with towels.

NOTE: A single extremely light fabric item may need to have an additional item included in

the STEAM Refresh cycle to achieve optimum results.

FecoDry

Available for BULKY, TOWELS/Sheets, NORMAL/Cottons, MIXED LOAD, JEANS, and DELICATES. When

the ecoDry button is pressed, cycle settings change to reduce the total energy consumption of the selected

sensor cycle. NOTE: Cycle times will change when ecoDry is selected. The ecoDry option will default to on

for NORMAL/Cottons. For optimal energy savings, turn ecoDry on. For optimal drying times, turn ecoDry

off. NOTE: Energy savings will vary across loads and cycles.

849-3000244 Rev 5

Settings

Individual settings for cycle minutes (Time), dryness level (Level) and temperature (Temp) can be set from the

minimum (lowest in column) to maximum (highest in column). In general, the higher up the column, the more

energy will be used.

Dryness Level Description Light ON from bottom

indicates setting:

Max Dry Use for heavy-duty fabrics. 5

More Dry Use for mixed type fabrics. 4

Dry Use for a normal dryness level suitable for most loads. This is the

preferred cycle for energy savings. 3

Less Dry Use for lighter fabrics.

Damp For leaving items partially damp. 1

Temperature Description Light ON from bottom

indicates setting:

Hot For regular to heavy cottons. 5

Medium For synthetics, blends, delicates and items labeled permanent press. 4

Low For delicates, synthetics and items labeled tumble dry low. 3

Extra Low For delicates, synthetics and items labeled extra care or gentle dryness.

No Heat For fluffing items without heat. For use only with the TIMED DRY cycle. 1

Wrinkle Care

Use this option to minimize the wrinkles in clothes. It provides 1 hour of no-heat tumbling after the clothes are

dry. If you have Sound option enabled and you select the Wrinkle Care option, a signal will sound at the end of

the drying time and several times during the Wrinkle Care cycle. This will remind you that it is time to remove

the clothes.

Damp Alert

This option causes the dryer to beep when clothes have dried to a damp level. Remove items that you wish

to hang dry. The Damp Alert will only beep when this option is selected (but the dry cycle will keep running).

Removing clothes and hanging them when they are damp, can reduce the need to iron some items. The light

beside the button will be lit when Damp Alert is on.

NOTE: On some models this features is only available through the GE Appliances SmartHQ App.

• Remove garments promptly at the sound of signal. Place clothes on hangers so wrinkles will not set in.

• Use the Damp Alert especially when drying fabrics like polyester, knits and permanent press. These fabrics

should be removed so wrinkles will not set in.

My Cycle

As the cycle selector knob is turned, the Time (timed dry), Level (dryness level) and Temp (temperature)

settings change to automatic pre-set default settings. If you desire a different setting, press the appropriate

button(s). Then press and hold the My Cycle button for 3 seconds and the dryer will “remember” these settings

for that Knob Selection. In the future, when you turn the selector knob to that cycle, your settings will be

automatically recalled. NOTE: Signal sound cannot be set for My Cycle.

NOTE: On some models this features is only available through the GE Appliances SmartHQ App.

Washer Link

This feature wirelessly links your washer to your dryer and uses the connection information to automatically

adjust the settings of your dryer for the clothes just washed. If the dryer has a valid WiFi connection, and the

Washer Link option is selected, either via the button or the App, the light above the button will be lit. If the

option is not selected then the light will turn off. If the dryer does not have a valid WiFi connection, and this

option is selected, either via the button or the App, the WiFi light and the Washer Link light will blink and an

error tone will play. NOTE: Signal sound cannot be set for My Cycle.

NOTE: On some models this features is only available through the GE Appliances SmartHQ App.

Sound

Use the Sound button to change the volume of the pad presses and the end of cycle signal. Press the button until

you reach the desired volume or off.

NOTE: If your model doesn’t have a Sound button, press and hold the Wrinkle Care button for 3 seconds to toggle

sound option between enabled and disabled. “Sound on” will show on the display and a tone will sound when

enabled. “Sound off” will show on the display and no tone will sound when disabled.

Using the dryer

USING THE DRYER

49-3000244 Rev 5 9

USING THE DRYER

Using the dryer

MDrum Light

The drum light will turn on if, the Light button is pressed, or the door is opened. It will turn off when the door is

shut, the Light button is pressed again or after 5 minutes if the door is left open.

NOTE: If your model doesn’t have the Light button, press and hold the Damp Alert button for 3 seconds to

turn on or off the light.

Tangle Control (on some models)

Activates alternating forward and reverse tumbling to reduce tangling, dry more evenly, and improve drying times.

Typical loads such as bed and bath mixed loads, where sheets, towels and pillow cases are laundered together,

benefit from this capability. When the dryer reverses direction, there will be a slight pause and sound change.

NOTE: Tangle Control is selected by default for TOWELS and BULKY cycles.

Reduce Static (on some models)

When selected, the dryer will spray a mist of water onto the load, at the end of the drying cycle, to reduce static.

NOTE: This option is not available with BULKY, SANITIZE or STEAM cycles.

10 49-3000244 Rev 5

Using the dryer

USING THE DRYER

Filling the Fabric Refresh Tank

This Scent Delivery System is approved to be used with the following liquids:

• Febreze FABRIC™ or Febreze FABRIC™ Extra Strength care

• Downy Wrinkle Releaser® – Light Fresh

The use of any liquid or substance with the Fabric Refresh System, other than those listed above, is strictly

prohibited and may result in a risk of fire, explosion, electric shock, hazardous fumes, or injury to persons.

Doing so may also damage your dryer and void your Warranty.

The Fabric Refresh System is located on the inside of the dryer door and has a dedicated tank for the approved liquids.

To fill the tank:

1 Press the button to release the Fabric Refresh door,

and then pull it down to open.

NOTE: The tank may be filled in place or it may be

removed by grasping its handle and pulling it out.

2 Release the tank cap by turning it counter-clockwise

and lift it up to remove.

3 Pour the liquid fragrance into the tank. Make sure to

not exceed the fill level indicated inside the tank.

4 Replace the tank cap and turn it clockwise making

sure the indents align.

5 If removed, replace the tank into its compartment in

the door making sure it is firmly seated. Close the

Fabric Refresh door.

Fabric Refresh (on some models)

Available for all cycles. When the Fabric Refresh button is pressed, the cycle settings will change to dispense

a dose of fragrance into your dryer to give a fresh scent to your clothes.

There are 3 levels: Auto, More and Less. Each level is intended to give an appropriate dose of fragrance

according to the amount of clothes placed inside the dryer. Press the Fabric Refresh button to switch between

Less, Auto, More or off.

Auto: Recommended to use with average load sizes to provide a light fresh scent.

More: Recommended to use with large load sizes to provide a more intense scent.

Less: Recommended to use with small loads or fewer garments to give a soft scent.

NOTES:

• Dosing will depend on the cycle selected.

• Dosing may change on the same cycle due to temperature and load size.

• Dosing may be adjusted to provide more or less of the fresh scent liquid.

49-3000244 Rev 5 11

Drying Rack (on some models)

A handy drying rack may be used for drying delicate items such as

washable sweaters.

To install the drying rack:

1 Lift the lint filter slightly. (Do not remove the lint filter completely).

2 Place the rack in the dryer and lower its front legs and hook them in

the slots.

3 Press the rack down flat and lower the lint filter back down into

position.

NOTES:

• The drying rack must be used with the TIMED DRY cycle. Use with

sensor cycles may result in damp items or extended cycle times.

• Do not use this drying rack when there are other clothes in the dryer.

• If your model did not come with a drying rack, order WE01X25160

on-line at GEApplianceparts.com, 24 hours a day or by phone at

877.959.8688 during normal business hours.

Always follow fabric manufacturer’s care label when laundering.

As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer. Try also to

sort items according to size. For example, do not dry a sheet with socks or other small items.

Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. Bounce®

Fabric Conditioner Dryer Sheets have been approved for use in this dryer when used in accordance with the

manufacturer’s instructions.

Do not overload. This wastes energy and causes wrinkling.

Sorting and Loading Hints

Lift filter and hook front

rack legs into slots

Keep flammable materials and vapors, such as

gasoline, away from dryer.

DO NOT dry anything that has ever had anything

flammable on it (even after washing).

No washer can completely remove oil.

DO NOT dry anything that has ever had any type of oil

on it (including cooking oils).

Items containing foam, rubber, or plastic must be dried

on a clothesline.

Failure to do so can result in death, explosion, or fire.

- Fire Hazard

12 49-3000244 Rev 5

VENTING

Venting

Venting the Dryer

For the best drying performance, the dryer needs to be properly vented. The dryer will use more energy and run longer if it is

not vented to the specifications below. Carefully follow the details on Exhausting in the Installation Instructions.

Use only rigid metal 4” diameter ductwork inside the dryer cabinet. Use only rigid

metal or UL listed flexible metal 4” diameter ductwork for exhausting to the outside.

Do not use plastic or other combustible ductwork.

Use the shortest length possible.

Do not crush or collapse.

Avoid resting the duct on sharp objects.

Venting must conform to local building codes.

This dryer MUST be exhausted to the outdoors.

Use only 4” rigid metal ducting for the home exhaust duct.

Use only 4” rigid metal or UL-listed dryer transition duct to connect the dryer to the home exhaust.

DO NOT use a plastic vent.

DO NOT exhaust into a chimney, kitchen exhaust, gas vent, wall, ceiling, attic, crawl space, or

concealed space of a building.

DO NOT install a screen in or over the exhaust duct.

DO NOT install a booster fan in the exhaust duct.

DO NOT use duct longer than specified in the exhaust length table.

Failure to follow these instructions can result in death or fire.

- Fire Hazard

Correct

Venting

Incorrect

Venting

Vent Health

Is a diagnostic test to verify the status of the venting system. NOTE: To run the test, ambient temperature must be

below 85°F (if temperature is above 85°F the test will be invalid and the main display will show “00”).

NOTE: On some models this features is only available through the GE Appliances SmartHQ App.

To enter Vent Health test mode:

1 Ensure the drum is empty.

2 Ensure the lint filter is clean.

3 Press and hold the Time and Level buttons for 3 seconds.

4 Close the door and press Start.

After the test is run, the display will show a number. Use the table below to understand the result and the action needed.

Main Display LED Display Result Action*

01 OFF Clean/Normal Your house vent is in good condition

and no action is required.

02 OFF May need attention

Your house vent condition may affect your

dryer’s performance. Check and clean

or make adjustments to improve.

03 Vent Blocked Blocked

Your house vent is highly restricted and

is affecting your dryer’s performance.

Clean and/or make needed

adjustments to improve.

*Also see Interior and Duct in the Care and Cleaning section.

49-3000244 Rev 5 13

CARE AND CLEANING

Care and Cleaning

Fabric Refresh Tank

Clean the tank when switching to a different approved liquid or as needed. The tank is located on the inside of the

dryer door.

To clean the tank:

1 Press the button to release the Fabric Refresh door,

and then pull it down to open.

2 Remove the tank by grasping its handle and pulling it

out.

3 Release the tank cap by turning it counter-clockwise

and lift it up to remove.

4 Run hot water into the tank. Replace the tank cap

and turn it clockwise making sure the indents align.

Shake the tank gently.

5 Drain the water over a sink by pressing the drain

button located at the bottom of the tank.

Repeat fill, shake and drain until the water is clear.

6 Replace the tank by aligning it properly to its

compartment and sliding it back into place.

Make sure to push it all the way in.

7 Close the Fabric Refresh door.

Water might be hot. Wear heavy rubber dish

washing gloves to press the drain button to avoid

the draining hot water.

Fill with hot water and replace cap

Shake gently to clean

Press to drain water

14 49-3000244 Rev 5

Exterior

Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged

by some laundry pretreatment soil and stain remover products. Apply these products away from the dryer. The fabric

may then be washed and dried normally. Damage to your dryer caused by these products is not covered by your

warranty.

Stainless Steel

To clean stainless steel surfaces use a damp cloth with a mild, non-abrasive cleaner suitable for stainless steel

surfaces. Remove the cleaner residue and then dry with a clean cloth.

The stainless steel used to make the dryer drum provides the highest reliability available in a GE Appliances dryer.

If the dryer drum should be scratched or dented during normal use, the drum will not rust or corrode. These surface

blemishes will not affect the function or durability of the drum.

Interior and Duct

The interior of the appliance and exhaust duct should be cleaned once a year by qualified service personnel.

The Exhaust Duct: Inspect and clean the exhaust ducting at least once a year to prevent clogging. A partially clogged

exhaust can lengthen the drying time.

Follow these steps:

1 Turn off electrical supply by disconnecting the plug from the wall socket.

2 Disconnect the duct from the dryer.

3 Vacuum the duct with the hose attachment and reconnect the duct.

The Exhaust Hood: Check with a mirror that the inside flaps of the hood move freely when operating. Make sure that there

is no wildlife (birds, insects, etc.) nesting inside the duct or hood.

Drum Light

The drum light is an LED light. Replacement must be done by a qualified technician.

CARE AND CLEANING

Care and Cleaning

Fabric Refresh Nozzle

Drips may occur from the nozzle and periodic cleaning may be required.

Use a damp wash cloth to wipe the liquid residue off the Nozzle and

below the nozzle. This should be done whenever liquid residue or lint

build up is noticed.

Lint Filter

Clean the lint filter before each use.

Remove by pulling straight up. Run your fingers across the filter.

A waxy buildup may form on the lint filter from using dryer added

fabric softener sheets.

To remove this buildup, wash the lint screen in warm, soapy water.

Dry thoroughly and replace.

Vacuum the lint from the dryer lint filter area if you notice a change in

dryer performance.

NEVER OPERATE THE DRYER WITHOUT ITS FILTER IN PLACE.

49-3000244 Rev 5 15

Troubleshooting Tips... Before you call for service

TROUBLESHOOTING TIPS

Problem Possible Cause What To Do

Dryer shakes or

makes noise Some shaking/noise is normal.

Dryer may be sitting unevenly. Move dryer to an even floor space, or adjust leveling legs as

necessary until even.

Clothes take

too long to dry Improper or obstructed

ducting Check the Installation Instructions to make sure the dryer

venting is correct.

Make sure ducting is clean, free of kinks and unobstructed.

Check to see if outside wall damper operates easily.

Improper sorting Separate heavy items from lightweight items (generally, a

well-sorted washer load is a well-sorted dryer load).

Large loads of heavy fabrics

(like beach towels) Large, heavy fabrics contain more moisture and take longer to dry.

Separate large, heavy fabrics into smaller loads to speed drying time.

Controls improperly set Match control settings to the load you are drying.

Lint filter is full Clean lint filter before every load.

Blown fuses or tripped

circuit breaker Replace fuses or reset circuit breakers. NOTE: Some electric

dryers use 2 fuses/breakers, make sure both are operating.

Overloading/combining loads Do not put more than one washer load in the dryer at a time.

Underloading If you are drying only one or two items, add a few items to ensure

proper tumbling.

ecoDry is enabled The ecoDry feature is designed to operate your dryer in the

most energy efficient mode, which is not always the fastest

mode. In some instances, dry times may be extended to

reduce overall energy usage for the cycle.

The Dry dryness

level was

chosen but load

is still damp

Load consists of a mixture of

heavy and light fabrics When combining heavy and light fabrics in a load, choose Max

Dry.

Exhaust system is blocked Inspect and clean exhaust system.

Dryer doesn’t

start Control panel is “asleep” This is normal. Press Power to activate the control panel.

Dryer is unplugged Make sure the dryer plug is pushed completely into the outlet.

Fuse is blown/circuit breaker

is tripped Check the building’s fuse/circuit breaker box and replace fuse

or reset breaker. NOTE: Some electric dryers use two fuses/

breakers, make sure both are operating.

Dryer was accidentally paused

when starting Delay Dry If the light on the Start/Pause button is flashing, the dryer is

paused. Press Start/Pause to restart the countdown.

No numbers

displayed

during cycle,

only lights

Dryer is continuously

monitoring the amount of

moisture in the clothes

This is normal. When the dryer senses a low level of moisture in

the load, the dryer will display the dry time remaining.

Time Remaining

jumped to a

lower number

The estimated time may

change when a smaller load

than usual is drying

This is normal.

Cannot make a

selection and

the dryer beeps

twice

The dryness Level, Temp or

option that you are trying to

select is incompatible with

the chosen dry cycle

This is normal.

Dryer is running

but 00 is

displayed in

Time Remaining

The Wrinkle Care option

was chosen This is normal. During extended tumbling, the time remaining is

not displayed. The extended tumbling option lasts approximately

60 minutes.

“Vent Blocked”

light is on Lint filter is full Clean lint filter, dry a load on an automatic cycle and verify that

light turns off.

Improper or obstructed

ducting Check the Installation Instructions to make sure the dryer venting

is correct.

Make sure ducting is clean, free of kinks and unobstructed. Check

to see if outside wall damper operates easily.

Dry a load on an automatic cycle and verify that light turns off.

Exhaust system is blocked Inspect and clean the exhaust system.

Dry a load on an automatic cycle and verify that light turns off.

16 49-3000244 Rev 5

TROUBLESHOOTING TIPS

Troubleshooting Tips... Before you call for service

Problem Possible Causes What To Do

Dryer doesn’t

heat Fuse is blown/circuit breaker

is tripped; the dryer may

tumble but not heat

Check the building’s fuse/circuit breaker box and replace both

fuses or reset both breakers. Your dryer may tumble if only one

fuse is blown or one breaker tripped. NOTE: Some electric

dryers use 2 fuses/breakers, make sure both are operating.

Gas service is off (gas

models only) Make sure gas shutoff at dryer and main shutoff are fully open.

LP gas supply tank is empty

or there has been a utility

interruption of natural gas

(gas models only)

Refill or replace tank. Dryer should heat when utility service is

restored.

No heat temperature selected Select another heat setting

Inconsistent

drying times Type of heat Drying time will vary according to the type of heat used. If

you recently changed from an electric to a gas (natural or LP)

dryer, or vice versa, the drying time could be different.

Type of load and drying

conditions The load size, types of fabric, wetness of clothes and the

length and condition of the exhaust system will affect drying

times.

Clothes are still

wet and dryer

shut off after a

short time

The door was opened

mid-cycle. The load was then

removed from the dryer and

a new load put in without

selecting a new cycle

A dry cycle must be re-selected each time a new load is put in.

Small load When drying 3 items or less, choose QUICK DRY or TIMED DRY.

Load was already dry except

for collars and waistbands Choose QUICK DRY or TIMED DRY to dry damp collars and

waistbands. In the future, when drying a load with collars and

waistbands, choose More Dry.

Dryer is not level Move dryer to an even floor space or adjust leveling legs as

necessary until even.

Clothes are

wrinkled Overdrying Select a shorter drying time.

Remove items while they still hold a slight amount of moisture.

Select a Less Dry or Damp setting.

Letting items sit in dryer after

cycle ends Remove items when cycle ends and fold or hang immediately, or

use the Wrinkle Care option.

Overloading Separate large loads into smaller ones.

Clothes shrink Some fabrics will naturally

shrink when washed. Others

can be safely washed, but

will shrink in the dryer.

To avoid shrinkage, follow garment care labels exactly.

Some items may be pressed back into shape after drying.

If you are concerned about shrinkage in a particular

item, do not machine wash or tumble dry it.

Greasy spots

on clothes Improper use of fabric

softener Follow directions on fabric softener package.

Drying dirty items with clean

ones Use your dryer to dry only clean items. Dirty items can stain clean

items and the dryer.

Clothes were not completely

clean Sometimes stains which cannot be seen when the clothes are wet

appear after drying. Use proper washing procedures before drying.

Lint on clothes Lint filter is full Clean lint screen before each load.

Improper sorting Sort lint producers (like chenille) from lint collectors (like corduroy).

Static electricity can attract

lint See suggestions in this section under Static occurs.

Overloading Separate large loads into smaller ones.

Paper, tissue, etc., left in

pockets Empty all pockets before laundering clothes.

49-3000244 Rev 5 17

Troubleshooting Tips... Before you call for service

TROUBLESHOOTING TIPS

Problem Possible Causes What To Do

Static occurs No fabric softener was used Try a fabric softener.

Bounce® Fabric Conditioner Dryer Sheets have been approved for

use in all GE Appliances dryers when used in accordance with the

manufacturer’s instructions.

Overdrying Try a fabric softener.

Adjust setting to Damp.

Synthetics, permanent press

and blends can cause static Try a fabric softener.

Collars and

waistbands still

wet at end of

cycle

The dryness monitor senses

that the body of the clothes

is dry

Choose QUICK DRY or TIMED DRY to dry damp collars and

waistbands. In the future, when drying a load with collars and

waistbands, choose Max Dry.

Slight variation

in metallic color This is normal Due to the metallic properties of paint used for this unique product,

slight variations of color may occur due to viewing angles and

lighting conditions.

Dryer continues

to tumble after

display says

Complete

Wrinkle Care was selected Ensure Wrinkle Care option is not selected.

Water on floor in

back of dryer Loose water hose connection Tighten connection.

Hose missing rubber washer

at connection with valve Install rubber washer provided with hose.

Garments still

wrinkled after

steam cycle

Too many garments Load fewer garments; manually increase time.

Lint filter not clean Clean lint filter

Load is children/infant

garments Use the STEAM Refresh cycle.

Door is too

foggy to see

clothes during a

steam or Fabric

Refresh cycle

Steam and fabric refresher

condenses on inner door This is normal.

Water seen on

inside of door

and top of lint

filter when

opening door

after steam or

Fabric Refresh

cycle

Steam and fabric refresher

condenses on these surfaces This is normal.

Small areas

on clothes are

damp after

steam or Fabric

Refresh cycle

Steam condenses on inner

drum If using the STEAM Dewrinkle cycle, manually reduce the cycle

time. If using the STEAM Refresh cycle, add more garments to

the load.

Fabric refresher condenses

on inner drum If using the MORE setting on a Fabric Refresh cycle, with small

loads, it may cause spots. Use AUTO or LESS setting to prevent

damp spots.

Small amount of

water on floor in

front of dryer

Inadequate load size for

steam cycle selected, excess

steam condenses inside

cabinet and leaks out

If using the STEAM Dewrinkle cycle, manually reduce the cycle

time. If using the STEAM Refresh cycle, add more garments to

the load.

Inadequate load size for

Fabric Refresh setting cycle

selected, excess fabric

refresher condenses inside

cabinet and leaks out

Using the More setting on a cycle, with small loads, may cause

spots. Use Auto or Less setting to prevent damp spots.

18 49-3000244 Rev 5

TROUBLESHOOTING TIPS

Troubleshooting Tips... Before you call for service

Problem Possible Causes What To Do

Water drips

from door when

opened after a

Steam or Fabric

Refresh cycle

Steam and fabric refresher

condenses on inner door This is normal.

Fabric Refresh tank is loose

or not fully seated in its

compartment

Ensure the tank is placed correctly and firmly seated to the bottom

of its compartment

Cannot see

steam or fabric

refresher at

beginning of

cycle

Steam and fabric refresher

are released at different times

during the cycle

This is normal.

Cannot see

steam during

cycle

The steam nozzle might be

clogged with debris from your

water supply

Call GE Appliances at 877.959.8688 to order steam nozzle

replacement kit WE25M71 or to request a technician to replace

this for you.

Fabric Refresh

Door Open

displayed

Fabric Refresh door not

closed properly Verify that the Fabric Refresh door is closed before running a

cycle. If the Fabric Refresh door is not properly and fully closed the

dryer will sense an improper door connection.

Garments with

no perceptible

refresher scent

after Fabric

Refresh cycle

Too many garments Load fewer garments or increase the drying time.

Select the More setting in cases where Less or Auto where

previously selected.

Fabric Refresh tank is empty Verify that tank has enough liquid to ensure a proper dosing in a

cycle.

The Fabric Refresh nozzle

might be clogged with lint Remove the lint from the nozzle.

The Fabric Refresh nozzle

might be clogged with lint or

debris from liquid sediments

Call GE Appliances at 877.959.8688 to order Fabric Refresh

nozzle replacement kit WE01X34098 or to request a technician to

replace this for you.

49-3000244 Rev 5 19

GEAppliances.com

All warranty service is provided by our Factory Service Centers, or an authorized Customer Care

technician. To schedule

service online, visit us at

GEAppliances.com/service

, or call GE Appliances at 800.GE.CARES (800.432.2737). Please

have your serial number and your model number available when calling for service.

Servicing your appliance may require the use of the onboard data port for diagnostics. This gives a GE Appliances factory

service technician the ability to quickly diagnose any issues with your appliance and helps GE Appliances improve its

products by providing GE Appliances with information on your appliance. If you do not want your appliance data to be

sent to GE Appliances, please advise your technician not to submit the data to GE Appliances at the time of service.

LIMITED WARRANTY

GE Appliances Dryer Limited Warranty

Staple your receipt here. Proof of the original purchase

date is needed to obtain service under the warranty.

For the period of: We will replace:

One year

From the date of the

original purchase

Any part of the dryer which fails due to a defect in materials or workmanship. During

this limited one-year warranty, we will also provide, free of charge, all labor and

related service to replace the defective part.

What is not covered:

Service trips to your home to teach you how to use

the product.

Improper installation, delivery or maintenance.

Failure of the product if it is abused, misused, or used for

other than the intended purpose or used commercially.

Replacement of house fuses or resetting of circuit

breakers.

Products which are not defective or broken, or which

are working as described in the Owner’s Manual.

floods or acts of God.

possible defects with this appliance.

temperatures.

Extended Warranties: Purchase a GE Appliances extended warranty and learn about special discounts that are

available while your warranty is still in effect. You can purchase it online anytime at

GEAppliances.com/extended-warranty

or call 800.626.2224 during normal business hours. GE Appliances Service will still be there after your warranty expires.

In the United States:

This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for home use

within the USA. If the product is located in an area where service by a GE Appliances Authorized Servicer is not available,

you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Appliances

Service location for service. In Alaska, the limited warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty

gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your

legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: GE Appliances, a Haier Company, Louisville, KY 40225

EXCLUSION OF IMPLIED WARRANTIES

Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties,

including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the

shortest period allowed by law.

In Canada:

This limited warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada

for home use within Canada. If the product is located in an area where service by a GE Appliances Authorized Servicer is

not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized

GE Appliances Service location.

Some provinces do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty

gives you specific legal rights, and you may also have other rights which vary from province to province. To know what

your legal rights are, consult your local or provincial consumer affairs office.

Warrantor: MC Commercial Inc., Burlington, ON, L7R 5B6

20 49-3000244 Rev 5

Printed in Mexico

CONSUMER SUPPORT

Consumer Support

GE Appliances Website

Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day

of the year! You can also shop for more great GE Appliances products and take advantage of all our on-line support

services designed for your convenience. In the US: GEAppliances.com.

In Canada: GEAppliances.ca.

communication and prompt service under the terms of your warranty, should the need arise. You may also mail in

the pre-printed registration card included in the packing material. In the US: GEAppliances.com/register.

In Canada: Prodsupport.mabe.ca/crm/Products/ProductRegistration.aspx.

Schedule Service

Expert GE Appliances repair service is only one step away from your door. Get on-line and schedule your service at

your convenience any day of the year. In the US: GEAppliances.com/service or call 800.432.2737 during normal

business hours.

In Canada: GEAppliances.ca/en/support/service-request or call 800.561.3344.

Extended Warranties

Purchase a GE Appliances extended warranty and learn about special discounts that are available while your

warranty is still in effect. You can purchase it on-line anytime. GE Appliances Services will still be there after your

warranty expires. In the US: GEAppliances.com/extended-warranty or call 800.626.2224 during normal business

hours.

In Canada: GEAppliances.ca/en/support/purchase-extended-warranty or call 866.277.9842.

Remote Connectivity

For assistance with wireless network connectivity (for models with remote enable), in the US visit our website at

GEAppliances.com/connect or call 800.220.6899.

In Canada: GEAppliances.ca/connect or call 800.220.6899.

Parts and Accessories

Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes

(VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day.

In the US: GEApplianceparts.com or by phone at 877.959.8688 during normal business hours.

In Canada: GEAppliances.ca/en/products/parts-filters-accessories or call 800.661.1616.

Instructions contained in this manual cover procedures to be performed by any user. Other servicing

generally should be referred to qualified service personnel. Caution must be exercised, since improper

servicing may cause unsafe operation.

If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the

details including your phone number, or write to:

In the US: General Manager, Customer Relations | GE Appliances, Appliance Park | Louisville, KY 40225

GEAppliances.com/contact or call 800.626.2000

In Canada: Director, Consumer Relations, MC COMMERCIAL INC. | Suite 310, 1 Factory Lane | Moncton, N.B. E1C 9M3

GEAppliances.ca/en/contact-us or call 877.994.5366

La page charge ...

GE Profile 7.4 Cu Ft Le manuel du propriétaire

Marque: GE Profile

Modèle: 7.4 Cu Ft

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: GE Profile 7.4 Cu Ft Owner's manual
español: GE Profile 7.4 Cu Ft El manual del propietario

GE Profile 7.4 Cu Ft Le manuel du propriétaire

GE Profile 7.4 Cu Ft Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents