Maytag MER6875AA Mode d'emploi

Safety.......................................... 1-3

Surface Cooking ...................... 4-7

Controls

Smoothtop Surface

Warming Center

Oven Cooking ......................... 8-18

Control Panel

Baking

Cook & Hold

Delay

Toasting

Broiling

Keep Warm

Favorite

Oven Racks

Table of Contents

®

Care & Cleaning ...................19-22

Self-Clean Oven

Cleaning Procedures

Maintenance .........................23-24

Oven Doors

Oven Window

Oven Light

Troubleshooting ...................25-26

Warranty & Service.................... 27

Guide d’utilisation et

d’entretien ................................... 28

Guía de Uso y Cuidado ............. 58

Maytag Electric Smoothtop

Double Oven Range

Precision Touch 850 Series

Use and Care Guide

1

Installer: Please leave this guide with this appliance.

Consumer: Please read and keep this guide for future refer-

ence. Keep sales receipt and/or canceled check as proof of

purchase.

Model Number __________________________________

Serial Number __________________________________

Date of Purchase ________________________________

If you have questions, call:

Customer Assistance

1-800-688-9900 USA

1-800-688-2002 Canada

1-800-688-2080 (U.S. TTY for hearing or speech impaired)

(Mon.-Fri., 8 am-8 pm Eastern Time)

Internet: http://www.maytag.com

In our continuing effort to improve the quality and performance

of our cooking products, it may be necessary to make changes

to the appliance without revising this guide.

For service information, see page 27.

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible conditions

and situations that may occur. Common sense, caution,

and care must be exercised when installing, maintaining,

or operating the appliance.

Always contact your dealer, distributor, service agent, or

manufacturer about problems or conditions you do not

understand.

Recognize Safety Symbols, Words, Labels

WARNING – Hazards or unsafe practices which

COULD result in severe personal injury or death.

CAUTION – Hazards or unsafe practices which

COULD result in minor personal injury.

WARNING

CAUTION

• ALL RANGES CAN TIP AND

CAUSE INJURIES TO PERSONS

• INSTALL ANTI-TIP DEVICE

PACKED WITH RANGE

• FOLLOW ALL INSTALLATION

INSTRUCTIONS

WARNING: To reduce risk of

tipping of the appliance from

abnormal usage or by excessive

loading of the oven doors, the appliance must

be secured by a properly installed anti-tip

device.

Read and follow all instructions before using this

appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a

result of improper usage of the appliance. Use appliance

only for its intended purpose as described in this guide.

To check if device is properly installed, look underneath

range with a flashlight to make sure one of the rear

leveling legs is properly engaged in the bracket slot. The

anti-tip device secures the rear leveling leg to the floor

when properly engaged. You should check this anytime

the range has been moved.

WARNING

Important Safety

Instructions

To ensure proper and safe operation: Appliance must

be properly installed and grounded by a qualified techni-

cian. Do not attempt to adjust, repair, service, or replace

any part of your appliance unless it is specifically recom-

mended in this guide. All other servicing should be

referred to a qualified servicer.

Always disconnect power to appliance before servicing.

General Instructions

In Case of Fire

Turn off appliance and ventilating hood to avoid spreading

the flame. Extinguish flame then turn on hood to remove

smoke and odor.

• Cooktop: Smother fire or flame in a pan with a lid or

cookie sheet.

NEVER pick up or move a flaming pan.

• Ovens: Smother fire or flame by closing the oven doors.

Do not use water on grease fires. Use baking soda, a dry

chemical or foam-type extinguisher to smother fire or

flame.

WARNING

NEVER use an appliance as a step to reach cabinets

above. Misuse of appliance doors, such as stepping,

leaning or sitting on the doors, may result in possible

tipping of the appliance, breakage of doors, and serious

injuries.

2

Important Safety Instructions

If pan is smaller than element, a portion of the element will

be exposed to direct contact and could ignite clothing or

potholder.

Only certain types of glass, glass-ceramic, ceramic, earthen-

ware, or other glazed utensils are suitable for cooktop or

oven service without breaking due to the sudden change in

temperature. Follow utensil manufacturer’s instructions

when using glass.

This appliance has been tested for safe performance using

conventional cookware. Do not use any devices or accesso-

ries that are not specifically recommended in this manual.

Do not use stove top grills or add-on oven convection

systems. The use of devices or accessories that are not

expressly recommended in this manual can create serious

safety hazards, result in performance problems, and reduce

the life of the components of this appliance.

Turn pan handle toward center of cooktop, not out into the

room or over another surface element. This reduces the risk

of burns, ignition of flammable materials, or spillage if pan is

accidently bumped or reached by small children.

If appliance is installed near a window, precautions should be

taken to prevent curtains from blowing over surface ele-

ments.

NEVER use appliance to warm or heat the room. Failure to

follow this instruction can lead to possible burns, injury, fire,

or damage to the appliance.

NEVER wear loose-fitting or hanging garments while using

the appliance. Clothing could catch utensil handles or ignite

and cause burns if garment comes in contact with hot

heating elements.

To ensure proper operation and to avoid damage to the

appliance or possible injury, do not adjust, service, repair or

replace any part of the appliance unless specifically recom-

mended in this guide. Refer all other servicing to a qualified

technician.

NEVER store or use gasoline or other combustible or flam-

mable materials in the ovens, near surface units or in the

vicinity of this appliance as fumes could create a fire hazard

or an explosion.

To prevent grease fires, do not let cooking grease or other

flammable materials accumulate in or near the appliance.

Use only dry potholders. Moist or damp potholders on hot

surfaces may result in a steam burn. Do not let potholders

touch hot heating elements. Do not use a towel or other

bulky cloth which could easily touch hot heating elements

and ignite.

Always turn off all controls when cooking is completed.

NEVER heat unopened containers on the surface unit or in

the ovens. Pressure build-up in the container may cause

container to burst resulting in burns, injury or damage to the

appliance.

NEVER use aluminum foil to cover oven racks or oven

bottoms. This could result in risk of electric shock, fire, or

damage to the appliance. Use foil only as directed in this

guide.

Aerosol-type cans are EXPLOSIVE when exposed to heat and

may be highly flammable. Do not use or store near appliance.

Cooktop

NEVER leave surface units unattended especially when

using high heat. An unattended boilover could cause smok-

ing and a greasy spillover can cause a fire.

This appliance is equipped with different size surface ele-

ments. Select pans with flat bottoms large enough to cover

element. Fitting pan size to element will improve cooking

efficiency.

Glass-Ceramic Cooktop

NEVER cook on broken cooktop. If cooktop should break,

cleaning solutions and spillovers may penetrate the broken

cooktop and create a risk of electric shock. Contact a

qualified technician immediately.

Clean cooktop with caution. Some cleaners can produce

noxious fumes if applied to a hot surface. If a wet sponge,

cloth, or paper towel is used on a hot cooking area, be

careful to avoid steam burn.

Deep Fat Fryers

Use extreme caution when moving the grease pan or

disposing of hot grease. Allow grease to cool before at-

tempting to move pan.

Ovens

Use care when opening doors. Let hot air or steam escape

before removing or replacing food.

For proper oven operation and performance, do not block or

obstruct oven vent duct. When ovens are in use, the vent

and surrounding area near the vent may become hot

enough to cause burns.

Always place oven racks in desired locations while ovens

are cool. If rack must be moved while an oven is hot, do

not let potholder contact hot element in oven.

3

Important Safety Instructions

Save These Instructions for Future Reference

CAUTION

Before self-cleaning the oven, remove the oven

racks, broiler pan, food and any other utensils. Wipe

spillovers to prevent excessive smoke and flare-ups.

CAUTION

NEVER store items of interest to children in cabinets above

an appliance. Children climbing on the appliance or on the

appliance doors to reach items could be seriously injured.

Self-Cleaning Ovens

NEVER leave children alone or unsupervised in area where

appliance is in use or is still hot.

NEVER allow children to sit or stand on any part of the

appliance as they could be injured or burned.

Children must be taught that the appliance and utensils in

or on it can be hot. Let hot utensils cool in a safe place, out

of reach of small children. Children should be taught that an

appliance is not a toy. Children should not be allowed to

play with controls or other parts of the unit.

Ventilating Hoods

Clean range hood and filters frequently to prevent grease or

other flammable materials from accumulating on hood or

filter and to avoid grease fires.

Turn the fan on when flambéing foods (such as Cherries

Jubilee) under the hood.

Important Safety Notice and

Warning

The California Safe Drinking Water and Toxic Enforce-

ment Act of 1986 (Proposition 65) requires the Governor

of California to publish a list of substances known to the

State of California to cause cancer or reproductive harm,

and requires businesses to warn customers of potential

exposures to such substances.

Users of this appliance are hereby warned that when the

oven is engaged in the self-clean cycle, there may be

some low-level exposure to some of the listed sub-

stances, including carbon monoxide. Exposure to these

substances can be minimized by properly venting the

oven to the outdoors by opening the windows and/or

door in the room where the appliance is located during

the self-clean cycle.

IMPORTANT NOTICE REGARDING PET BIRDS: Never

keep pet birds in the kitchen or in rooms where the

fumes from the kitchen could reach. Birds have a very

sensitive respiratory system. Fumes released during an

oven self-cleaning cycle may be harmful or fatal to birds.

Fumes released due to overheated cooking oil, fat,

margarine and overheated non-stick cookware may be

equally harmful.

Clean only parts listed in this guide. Do not clean door

gaskets. The gaskets are essential for a good seal. Do not

rub, damage, or move the gaskets.

Do not use oven cleaners. No commercial oven cleaner or

oven liner protective coating of any kind should be used in or

around any part of the ovens.

Wipe up excessive spillovers, especially greasy spills, before

the clean cycle to prevent smoking, flare-ups or flaming.

It is normal for the cooktop to become hot during a clean

cycle. Therefore, avoid touching the cooktop, door, window or

oven vent during a clean cycle.

Heating Elements

NEVER touch surface or oven heating elements, areas near

elements, or interior surfaces of ovens.

Heating elements may be hot even though they are dark in

color. Areas near surface elements and interior surfaces of

the ovens may become hot enough to cause burns. During

and after use, do not touch or let clothing or other flammable

materials contact heating elements, areas near elements, or

interior surfaces of ovens until they have had sufficient time

to cool.

Other potentially hot surfaces include: Cooktop, areas facing

the cooktop, oven vent, and surfaces near the vent opening,

oven doors, areas around the doors and oven windows.

Child Safety

4

Surface Cooking

Surface Controls

Use to turn on the surface elements. An infinite choice of

heat settings is available from Low to High. The knobs can

be set on or between any of the settings.

Setting the Controls

1. Place pan on surface element.

2. Push in and turn the knob in either direction to the desired

heat setting.

• The control panel is marked to identify which

element the knob controls. For example, the

graphic at right indicates left front element.

3. There is an element “ON” indicator light on the control

panel. When any surface control knob is turned on, the

light will turn on. The light will turn off when all the

surface elements are turned off.

4. After cooking, turn knob to OFF. Remove pan.

Dual Elements

The cooking surface has two dual

elements located in the right front and

left front of the smoothtop. This allows

you to change the size of these

elements.

Press the switch to the left to use the

large element or to the right to use the

small element.

Medium (5-7): Use to

maintain slow boil for

large amounts of liquids

and for most frying

operations.

BEFORE COOKING

• Always place a pan on the surface unit before you turn it

on. To prevent damage to range, never operate surface

unit without a pan in place.

• NEVER use the cooktop as a storage area for food or

cookware.

DURING COOKING

• Be sure you know which knob controls which surface

unit. Make sure you turned on the correct surface unit.

• Begin cooking on a higher heat setting then reduce to a

lower setting to complete the operation. Never use a

high heat setting for extended cooking.

• NEVER allow a pan to boil dry. This could damage the

pan and the appliance.

• NEVER touch cooktop until it has cooled. Expect some

parts of the cooktop, especially around the surface units,

to become warm or hot during cooking. Use potholders

to protect hands.

CAUTION

Suggested Heat Settings

The size, type of cookware and cooking operation will affect

the heat setting. For information on cookware and other

factors affecting heat settings, refer to Cookware Recommen-

dations on page 7.

AFTER COOKING

• Make sure surface unit is turned off.

• Clean up messy spills as soon as possible.

OTHER TIPS

• If cabinet storage is provided directly above cooking

surface, limit it to items that are infrequently used and can

be safely stored in an area subjected to heat. Tempera-

tures may be unsafe for items such as volatile liquids,

cleaners or aerosol sprays.

• NEVER leave any items, especially plastic items, on the

cooktop. The hot air from the vent may ignite flammable

items, melt or soften plastics, or increase pressure in

closed containers causing them to burst.

• NEVER allow aluminum foil, meat probes or any other

metal object, other than a pan on a surface element, to

contact heating elements.

• NEVER store heavy items above the cooktop that could fall

and damage it.

Low (2): Use to

keep foods warm

and melt choco-

late and butter.

High (10): Use to bring

liquid to a boil. Always

reduce setting to a lower

heat when liquids begin to

boil or foods begin to cook.

Med. Low (3-4):

Use to continue

cooking covered

foods or steam

foods.

Med. High (8-9): Use

to brown meat, heat oil

for deep fat frying or

sauteing. Maintain fast

boil for large amounts

of liquids.

Flex Choice Warm

(right rear element only):

Uses a lower heat to

keep foods warm for

serving.

5

Smoothtop Surface Notes:

• On Canadian models, the smoothtop does NOT operate

during a clean cycle.

• Cooktop may emit light smoke and odor the first few

times the cooktop is used. This is normal.

• Smoothtop cooktops retain heat for a period of time

after the element is turned off. Turn the elements off

a few minutes before food is completely cooked and use

the retained heat to complete cooking. When the Hot

Surface Indicator light turns off, the cooking area will be

cool enough to touch. Because of the way they retain

heat, the smoothtop elements will not respond to

changes in settings as quickly as coil elements.

• In the event of a potential boilover, remove the pan from

the cooking surface.

• Never attempt to lift the cooktop.

• The smoothtop surface may appear discolored when it is

hot. This is normal and will disappear when the surface

cools.

Smoothtop Surface

Cooking Areas

The cooking areas on your range are identified by permanent

circles on the smoothtop surface. For most efficient cooking,

fit the pan size to the element size.

Pans should not extend more than

1

/

2

to 1-inch beyond

the cooking area.

When a control is turned on, a glow can be seen through the

smoothtop surface. The element will cycle on and off to

maintain the preset heat setting, even on High.

For more information on cookware, refer to Cookware

Recommendations on page 7.

Hot Surface Indicator Light

The Hot Surface indicator light is located on the

control panel. The light will be illuminated

when any cooking area is hot. It will remain on,

even after the control is turned off, until the area has cooled.

Surface Cooking

WARMING CENTER

DUAL

ELEMENT

Warming Center (style may vary by model)

Use the Warming Center to keep hot cooked foods warm, such

as vegetables, gravies and oven-safe dinner plates.

Setting the Control:

Touch the Surface Warming Center pad and

then the Autoset pad. Press Autoset pad again

to turn off.

Warming Center Notes:

• Never warm food for longer than one hour (eggs for 30

minutes), as food quality may deteriorate.

• Do not heat cold food on the Warming Center.

• Warming temperatures of the food will vary depending on

type and amount of food. Always hold food at proper food

temperatures. USDA recommends food temperatures

between 140°-170° F.

• Use only cookware and dishes recommended as safe for

oven and cooktop use.

• Always use oven mitts when removing food from the

Warming Center as cookware and plates will be hot.

• All foods should be covered with a lid or aluminum foil to

maintain food quality.

• When warming pastries and breads the cover should have

an opening to allow moisture to escape.

• Do not use plastic wrap to cover foods. Plastic may melt

on to the surface and be very difficult to clean.

SINGLE

ELEMENT

(WITH FLEX

CHOICE

WARM*

OPTION)

SINGLE

ELEMENT

* Flex•Choice Warm: This setting uses a very low heat

setting to keep delicate foods or foods in a covered pan

warm without cooking.

6

To Prevent Stains

• Never use a soiled dish cloth or sponge to clean the

cooktop surface. A film will remain which may cause stains

on the cooking surface after the area is heated.

• Continuously cooking on a soiled surface may/will result in

a permanent stain.

To Prevent Other Damage

• Do not allow plastic, sugar or foods with high sugar content

to melt onto the hot cooktop. Should this happen, clean

immediately. (See Cleaning, page 21.)

• Never let a pan boil dry as this will damage the surface and

pan.

• Never use cooktop as a work surface or cutting board.

• Never cook food directly on the surface.

• Do not use a small pan on a large element. Not only does

this waste energy, but it can also result in spillovers burning

onto the cooking area which requires extra cleaning.

• Do not use non-flat specialty items that are oversized or

uneven such as round bottom woks, rippled bottom and/or

oversized canners and griddles.

• Do not use foil or foil-type containers. Foil may melt onto

the glass. If metal melts on the cooktop, do not use. Call an

authorized Maytag Servicer.

Surface Cooking

Tips to Protect the

Smoothtop Surface

Cleaning (see page 21 for more information)

• Before first use, clean the cooktop.

• Clean your cooktop daily or after each use. This will keep

your cooktop looking good and can prevent damage.

• If a spillover occurs while cooking, immediately clean the

spill from the cooking area while it is hot to prevent a tough

cleaning chore later. Using extreme care, wipe spill with a

clean dry towel.

• Do not allow spills to remain on the cooking area or the

cooktop trim for a long period of time.

• Never use abrasive cleansing powders or scouring pads

which will scratch the cooktop.

• Never use chlorine bleach, ammonia or other cleansers not

specifically recommended for use on glass-ceramic.

To Prevent Marks & Scratches

• Do not use glass pans. They may scratch the surface.

• Never place a trivet or wok ring between the surface and

pan. These items can mark or etch the top.

• Do not slide aluminum pans across a hot surface. The pans

may leave marks which need to be removed promptly. (See

Cleaning, page 21.)

• Make sure the surface and the pan bottom are clean before

turning on to prevent scratches.

• To prevent scratching or damage to the glass-ceramic top,

do not leave sugar, salt or fats on the cooking area. Wipe

the cooktop surface with a clean cloth or paper towel

before using.

• Never slide heavy metal pans across the surface since

these may scratch.

7

Canning and Oversize

Cookware

All canners and large pots must have flat bottoms and

must be made from heavy-gauge materials. This is critical

on smoothtop surfaces. The base must not be more than

1 inch larger than the element.

When canners and pots do not meet these standards, cooking

times may be longer, and cooktops may be damaged.

Some canners are designed with smaller bases for use on

smoothtop surfaces.

When canning, use the High heat setting only until the

water comes to a boil or pressure is reached in the canner.

Reduce to the lowest heat setting that maintains the boil or

pressure. If the heat is not turned down, the cooktop may be

damaged.

Surface Cooking

Cookware Recommendations

Select Avoid

Flat, smooth-bottom Pans with grooved or warped bottoms.

pans. Pans with uneven bottoms do not cook

efficiently and sometimes may not

boil liquid.

Heavy-gauge pans. Very thin-gauge metal or glass pans.

Pans that are the Pans smaller or larger than the

same size as the element by 1 inch.

element.

Secure handles. Cookware with loose or broken handles.

Heavy handles that tilt the pan.

Tight-fitting lids. Loose-fitting lids.

Flat bottom woks. Woks with a ring-stand bottom.

Using the right cookware can prevent many problems, such

as food taking longer to cook or achieving inconsistent

results. Proper pans will reduce cooking times, use less

energy, and cook food more evenly.

Flat Pan Tests

See if your pans are flat.

The Ruler Test:

1. Place a ruler across the bottom of the pan.

2. Hold it up to the light.

3. Little or no light should be visible under the ruler.

The Bubble Test:

1. Put 1 inch of water in the pan. Place on cooktop and turn

control to High.

2. Watch the formation of the bubbles as the water heats.

Uniform bubbles mean good performance, and uneven

bubbles indicate hot spots and uneven cooking.

8

Oven Cooking

Control Panel

The control panel is designed for ease in programming. The display window on the control shows time of day, timer and oven functions.

Control panel shown includes model specific features. (Styling may vary depending on model.)

Using the Touchpads

• Press the desired pad.

• Press the number pads to enter time or temperature.

• Or, press the Autoset pad to enter temperature.

• A beep will sound when any pad is touched.

• A double beep will sound if a programming error occurs.

A Bake Use for baking and roasting.

B Broil Use for broiling and top browning.

C Clean Use to set self-clean cycle.

D Keep Warm Use to keep cooked food warm in oven.

E Toast Use for toasting bread and products

toasted in toaster or toaster oven.

F Number Pads Use to set time and temperature.

G CANCEL Cancels all operations except timer,

clock and Surface Warming Center.

H Convect Bake Use for convection baking.

I Convect Roast Use for convection roasting.

J Timer 1 or 2 Sets the timer.

K Clock Use to set time-of-day clock.

L Cook & Hold Bakes for a preset time, then keeps

food warm for 1 hour.

M Delay Programs the oven to start baking or

cleaning at a later time.

N Oven Light Use to turn the oven lights on or off.

O Favorite Use to set and save a specific Cook &

Hold procedure.

P Autoset Use to quickly set temperatures.

Q Surface Use to keep foods warm on the cooktop

Warming Center for serving.

A B C D E F

G H I J K L M N O P Q

NOTE: Four seconds after entering the time or tempera-

ture it will automatically be entered. If more than 30

seconds elapse between touching a function pad and the

number pads, the function will be canceled and the

display will return to the previous display.

Clock

The clock can be set to display time in a 12-hour or 24-hour

format. The clock is set at the factory for the 12-hour format.

To change the clock to 24-hour format:

1. Press and hold the Upper CANCEL pad and

Favorite pad for three seconds.

• 12 Hr flashes in the display.

2. Press the Autoset pad to select 24 Hr; press

again to select 12 Hr.

3. Set the time of day following the directions in

the To set the Clock section.

To set the Clock:

1. Press the Clock pad.

• The time of day flashes in the display.

• Colon flashes in the display.

2. Press the appropriate number pads to set the time of day.

3. Press the Clock pad again or wait four seconds.

• The colon will remain on.

When electrical power is supplied or after a power interrup-

tion, the last clock time before power was interrupted will

flash.

To recall the time of day when another time function is

showing, press the Clock pad.

9

Oven Cooking

If an oven is currently in use, the touchpads and doors cannot

be locked.

The current time of day will remain in the display when the

touchpads and doors are locked.

To lock both doors:

1. Press and release CANCEL pad.

2. Press and hold the Upper Oven CANCEL and

Cook & Hold pads for three seconds.

• OFF appears in the display

• LOCK flashes while the doors are locking.

Both oven doors lock. LOCK remains in the display.

To unlock both doors:

Press and hold the Upper Oven CANCEL and Cook & Hold

pads for three seconds. OFF disappears from the display and

LOCK flashes while the doors are unlocking.

To cancel the Clock display:

If you do not want the time of day to display:

Press and hold the Upper Oven CANCEL and

Clock pads for three seconds. The time of day

will disappear from the display.

When the clock display is canceled, press the

Clock pad to briefly display the time of day.

To restore the Clock display:

Press and hold the Upper Oven CANCEL and Clock pads for

three seconds. The time of day will reappear in the display.

Timer

Each timer can be set from one minute (00:01) up to 99 hours

and 59 seconds (99:59).

The timers can be used independently of any other oven

activity. They can also be set while another oven function is

operating.

The Timers do not control the oven.

To set the Timer 1 or 2:

1. Press the Timer 1 or 2 pad.

• 00:00 and TIMER 1 or 2 flash in the display.

2. Press the appropriate number pads until the correct time

appears in the display.

• The colon and TIMER 1 or 2 will continue to flash.

• TIMER 1 or TIMER 2 will be displayed. If both timers are

active, TIMER 1 and TIMER 2 will be displayed.

3. Press Timer pad again or wait four seconds.

• The colon stops flashing and the time begins counting

down.

• The last minute of the timer countdown will be displayed

in seconds.

4. At the end of the set time, one long beep will sound and

“End” will be displayed.

5. Press the Timer pad to clear the display.

To cancel the Timer:

1. Press and hold the corresponding Timer pad

for three seconds.

OR

2. Press the Timer pad and press ‘0’ using

the number pads.

Locking the Control

and Oven Doors

The touchpad and oven doors can be locked for safety,

cleaning, or to prevent unwanted use. The touchpads will not

function when locked.

Note: The touchpads and oven doors cannot be locked if

the oven temperature is 400° F or above.

Fault Codes

BAKE or LOCK may flash rapidly in the display to alert you if

there is an error or a problem. If BAKE or LOCK flash in the

display, press CANCEL pad. If BAKE or LOCK continue to

flash, disconnect power to the appliance. Wait a few minutes,

and then reconnect power. If the flashing still continues,

disconnect power to the appliance and call an authorized

servicer.

Adjusting Sound Level

The factory default setting for sound is medium (MEd), but it

can be changed to low (LO) or high (HI). To change the

setting:

1. Press and hold Delay and upper oven CANCEL pads for

three seconds. A beep will sound. “bEEP” and the current

sound level (“LO”, “MEd” or “HI”) will appear in the

display.

2. Press the Autoset pad to increase or decrease the sound

level.

3. Wait four seconds and the new setting will be accepted.

4. If the Autoset pad is not pressed within 30 seconds, the

control will return to the existing setting.

Changing Temp °F/°C

The factory default setting for temperature is Fahrenheit. To

change the setting:

1. Press and hold the upper oven Bake and CANCEL pads for

3 seconds. A beep will sound and the current setting (°F

or °C) will appear in the display.

10

Oven Cooking

Baking Notes:

• If the lower oven is NOT in use, the upper oven will

preheat more quickly.

• Allow at least

1

/

2

-inch between the baking pan or

casserole and the top element in the upper oven.

Loaf, angel food or bundt pans are not recommended in

the upper oven.

• Do not use temperatures below 140° F to keep food warm

or below 200° F for cooking. For food safety reasons, lower

temperatures are not recommended.

• The back part of the lower oven bake element will not

glow red during baking. This is normal.

• When baking frozen, self-rise pizza in the upper oven,

place the pizza on a cookie sheet to avoid overbrowning.

• When preheating with a baking/pizza stone inside the

upper oven, do not set oven above 400° F. To use baking/

pizza stones at temperatures above 400° in the upper

oven, put stone in after the preheat beep.

• To change the oven temperature during cooking, press

Bake pad, then press the Autoset pad or appropriate

number pads until the desired temperature is displayed.

• To change the oven temperature during preheat,

press the Bake pad twice, then press the Autoset pad

or appropriate number pads until the desired tem-

perature is displayed.

• If you forget to turn off the oven, it will automatically turn

off at the end of 12 hours. If you wish to deactivate the

Automatic Shut Off/Sabbath Mode feature, see page 16.

Setting Oven Functions

Auto Set Pad

Use with function pads to automatically set:

• 350° F bake temperature

• HI or LO broil

• three hours of cleaning time

• four minutes of toasting time

• 170° F keep warm temperature

Baking

To set Bake:

1. Press the Bake pad for desired oven.

• BAKE and 000 will flash in the display.

2. Select the oven temperature. Press the Autoset

pad for 350° F or the appropriate number pads.

• Each additional press of the Autoset pad will increase

the temperature by 25°.

• The oven temperature can be set from 170° to 550°.

3. Press Bake pad again or wait four seconds.

• BAKE will stop flashing and light in the display.

• PREHEAT will light in the display.

• 100° or the actual oven temperature if over 100° F will

display. It will rise in 5° increments until the preset

temperature is reached.

4. Allow 4-10 minutes for the upper oven to preheat and 7-12

minutes for the lower oven to preheat.

• When the set oven temperature is reached, one long

beep will sound.

• The set temperature will display.

• PREHEAT will turn off.

• To recall set temperature during preheat, press Bake pad.

5. Place food in the oven.

6. Check cooking progress at the minimum cooking time.

Cook longer if needed.

7. When cooking is finished, press CANCEL pad.

8. Remove food from the oven.

Baking Differences Between Your Old

and New Oven

It is normal to notice some baking time differences between a new

oven and an old one. See “Adjusting the Oven Temperature” on

page 16.

2. Press the Autoset pad to change the setting between °F

and °C.

3. Wait 4 seconds and the new setting will be accepted.

4. If the Autoset pad is not pressed within 30 seconds, the

control will return to the existing setting.

Return To Factory Default

Settings

The control can be reset to the factory default settings. To

return to the default settings:

1. Press and hold upper oven Keep Warm and CANCEL pads

for 3 seconds. A single beep will sound and 12:00 will

appear in the display.

2. Reset the clock to the current time of day.

11

Oven Cooking

Roasting With Convection

(lower oven only)

When convection roasting, enter your normal roasting

time and temperature. The control will automatically

prompt you to check the food for doneness at 75% of the set

time. The convection fan will come on immediately after the

oven has turned on.

To set Convect Roast:

1. Press the Convect Roast pad.

• LOWER ROAST, the FAN icon and 00:00 will flash in the

display.

• 000 lights in the display.

2. Enter the roasting time using the number pads.

• Time can be set from 10 minutes (00:10) to 11 hours,

59 minutes (11:59).

• Press Convect Roast pad again or wait 4 seconds.

• LOWER ROAST and the FAN icon flash in the display.

• 000 will flash in the display.

3. Select the oven temperature. Press the

Autoset pad for 325° F or the appropriate number pads.

(Refer to Cooking Made Simple for roasting times.)

• Each additional press of the Autoset pad will increase

the temperature by 25°.

• The oven temperature can be set from 170° to 550°.

4. Press Convect Roast pad again or wait four seconds.

• ROAST will stop flashing and light in the display.

• 100° or the actual oven temperature will display. It will rise

in 5° increments until the preset temperature is reached.

• The FAN icon will start to rotate.

5. Place food in the oven.

• Time will start counting down once oven starts heating up.

• To recall the set temperature during preheat, press the

Convect Roast pad.

6. When 75% of the set cooking time has elapsed, the oven will

signal you to check the cooking progress. Cook longer if

needed.

3. Press Convect Bake pad again or wait four seconds.

• LOWER BAKE will stop flashing.

• PREHEAT and LOWER will light in the display.

• 100° or the actual oven temperature if over 100° F will

display. It will rise in 5° increments until the preset

temperature is reached.

• The FAN icon will start to rotate.

4. Allow the oven to preheat for 7-12 minutes.

• When the set oven temperature is reached, one long

beep will sound.

• PREHEAT will turn off.

• The set temperature will display.

• To recall the set temperature during preheat, press the

Convect Bake pad.

5. Place food in the oven.

6. Check cooking progress at the minimum cooking time.

Cook longer if needed.

7. When cooking is finished, press lower oven CANCEL pad.

8. Remove food from the oven.

Roasting Notes:

• When convection roasting, the cooking time must be set

before setting the temperature.

• If your recipe requires a preheated oven, add 15 minutes

to the cooking time programmed.

• Roasting times can vary with different cuts of meat.

• It is not necessary to preheat when convect roasting

large cuts of meat.

Baking with Convection (lower oven only)

When convection baking, enter your normal baking tempera-

ture. The control will automatically reduce the set oven

temperature by 25° (even though normal baking temperature

is displayed).

To set Convect Bake:

1. Press the Convect Bake pad.

• LOWER BAKE and the FAN icons will flash.

• 000 will flash in the display.

2. Select the oven temperature. Press the Autoset pad for

350° F or the appropriate number pads.

• Each additional press of the Autoset pad will increase

the temperature by 25 degrees. The oven temperature

can be set from 170° to 550°.

cont.

12

Oven Cooking

Do not use delayed baking for highly perishable foods such

as dairy products, pork, poultry, or seafood.

Cook & Hold

When using the Cook & Hold feature, the oven begins to heat

immediately after the control has been set. Then, the oven

cooks for a specified length of time. When that time has

elapsed, the oven will keep the food warm for up to one hour

then automatically turn off.

To set Cook & Hold:

1. Press the Cook & Hold pad once for upper oven

or twice for lower oven.

• HOLD will flash to indicate that you are in

Cook & Hold programming.

• 00:00 and either UPPER or LOWER will flash in the display.

2. Select the amount of time you want to cook by using the

number pads.

• HOLD continues to flash.

• The time will light in the display.

• Time can be set from 00:10 to 11:59.

3. Press Bake (upper and lower ovens), Convect

Bake or Convect Roast (lower oven only) and

select the oven temperature. Press the Autoset

pad for 350° F or the appropriate number pads.

• The desired function, 000 and either UPPER

or LOWER will flash.

• The oven temperature can be set from 170° F to 550° F.

4. Press the desired function pad again OR wait four seconds.

• The desired function will remain lit.

• The cooking time will show in the display.

• PREHEAT will show in the display.

• The actual oven temperature will be displayed

during preheat.

• The set temperature will display when the oven is

preheated.

When the cooking time has elapsed:

• Four beeps will sound.

• WARM and HOLD will light.

• 170° appears in the display.

Notes:

• Do not use Delayed Cook & Hold for items that require a

preheated oven, such as cakes, cookies, and breads.

• Do not use Delayed Cook & Hold if oven is already hot.

After one hour in WARM HOLD:

• The oven turns off automatically.

• Press CANCEL pad and remove food from the oven.

To cancel Cook & Hold at any time:

Press the CANCEL pad. Remove food from oven.

Delay Cook & Hold

When using Delay, the oven begins to cook later in the day.

Set the amount of time that you want to delay before the oven

turns on and how long you want to cook. The oven begins to

heat at the selected time and cooks for the specified length of

time, then keeps food warm for one hour.

Delay time can be set from 10 minutes (00:10) to 11 hours, 59

minutes (11:59).

To set a Delayed Cook & Hold cycle:

1. Press the Delay pad once to program the upper

oven or twice to program the lower oven.

• DELAY flashes in the display.

• 00:00 and either UPPER or LOWER flash in the display.

2. Using the appropriate number pads, enter the amount of

time you want to delay the start of the Cook & Hold cycle.

3. Press the Cook & Hold pad.

• HOLD and DELAY flash in the display.

• 00:00 and either UPPER or LOWER flash.

4. Enter the amount of time you want to cook using the

number pads.

5. Press Bake (upper and lower ovens), Convect Bake or

Convect Roast (lower oven only).

6. Set the oven temperature desired by pressing the Autoset

pad or the appropriate number pads.

• 350° will light when Autoset is pressed.

• After four seconds, the entered delay time

will appear in the display.

• BAKE and DELAY remain lit to remind you that

a delayed Cook & Hold function has been programmed.

• The oven light will remain on until the Oven Light pad is

pressed.

• Press any pad to recall the cook time remaining.

7. When cooking is finished, press CANCEL pad.

8. Remove food from the oven.

CAUTION

Toasting (upper oven only)

For toasting bread and products that are toasted in a toaster or

toaster oven.

1. Press the Toast pad.

2. Press the Autoset pad to set 4

minutes of toasting time.

Each additional press will

increase the toasting time

by 1 minute. TOAST and

the UPPER will be displayed. The toasting time will begin to

count down.

Or, press the appropriate number pads to set the toasting

time in minutes and seconds between 10 seconds and 6

minutes.

Example: To set toasting time for two minutes, press 2, 0, 0.

Browning time may vary, watch toasting carefully to avoid

over-browning. Close oven door during toasting.

3. At the end of the set toasting time, the oven will beep four

times.

Toasting Notes:

• Lower oven may not be operated while upper oven

is toasting. If the lower oven is operating when the

Toast pad is pressed, a beep will sound.

• Toasting is based on time not temperature.

• For more even browning results, preheat the oven 3-4

minutes.

• Toasting times will be shorter when the oven is hot or

when repeated toasting functions are done.

• For optimal results when toasting 4-5 pieces of bread or

other similar items, follow illustration above.

FOOD TOAST TIME*/COLD START

Sliced White Bread 3

1

/

2

- 4

1

/

2

min.

Waffles (frozen) 4 - 4

1

/

2

min.

Toaster Pastry (unfrozen) 3

1

/

2

- 4 min.

Toaster Pastry (frozen) 4

1

/

2

- 4

3

/

4

min

Tortillas (flour) 2

1

/

2

- 3 min.

Toaster Breaks** or 4 - 5 min.

Hot Pockets**

Bagels 4

1

/

2

- 5 min.

English Muffins 3

1

/

2

- 4 min.

Cheese Sandwich 3

1

/

2

- 4

1

/

2

min

Toasting Chart

* Toasting times are approximate and should be used as a

guide only.

** Brand names are registered trademarks of the respective

manufacturers.

13

Oven Cooking

14

Oven Cooking

Broiling

To set Broil:

1. Press the appropriate Broil pad.

• BROIL, UPPER and SET flash.

2. Press the Autoset pad once to set HI broil or

twice to set LO broil.

• HI or LO will be displayed.

Select HI broil for normal broiling. Select LO broil for

low-temperature broiling of longer cooking foods such

as poultry.

3. After four seconds, the oven will start.

• BROIL and HI or LO will remain lit.

4. For optimum browning, preheat broil element for 3-4

minutes before adding food.

5. Place food in the oven. Leave oven door open about four

inches (the first stop).

6. Turn meat once while cooking.

7. When food is cooked, press the CANCEL pad.

Remove food and broiler pan from the oven.

UPPER OVEN LOWER OVEN UPPER OVEN LOWER OVEN

FOODS RACK RACK SETTING COOK TIME COOK TIME

POSITION* POSITION* (MINUTES)** (MINUTES)**

Beef

Steak, 1” thick, on rack 4 HI 8 - 11 (medium) 15 - 19 (medium)

4 oz. Hamburgers, 3/4” thick (up to 12) on rack 4 HI 15 - 20 (well) 15 - 19 (well)

4 oz. Hamburgers, 3/4” thick (up to 6) on rack 4 HI 12 - 16 (well) 15 - 19 (well)

Chicken

Bone-in, skin-on breast

Pieces on rack 3 or 4 LO 25 - 36 (well) 28 - 39 (well)

Fish

Filets on rack 4 LO 8 - 12 (flaky) 8 - 13 (flaky)

Steaks, 1” thick on rack 4 LO 10 - 14 (flaky) 10 - 16 (flaky)

Pork

Chops, 1” thick on rack 4 HI 18 - 24 (well) 22 - 27 (well)

Broiling Chart - Broil times are based on a 4 minute preheat.

* When broiling fish, spray broil pan insert with cooking oil. Do not turn fish filets.

** Broiling times are approximate and may vary depending on the thickness of the food. Turn meat halfway through cooking times.

Broil Notes:

• For best results when broiling, use a two-piece broiler

pan.

• HI broil is used for most broiling. Use LO broil when

broiling longer cooking foods to allow them to cook to

well done stage without excessive browning.

• Broil times may be longer when the lower broiling

temperature is selected.

• Never cover broiler pan insert with aluminum foil. This

prevents fat from draining to the pan below.

• Expect broil times to increase and browning to be slightly

lighter if appliance is installed on a 208-volt circuit.

• If more than 30 seconds elapse between pressing the

Broil pad and the Autoset pad, the oven will not be set

and the display will return to the previous display.

• HI is used for most broiling. Use LO broil when broiling

longer cooking foods. The lower temperature allows

food to cook to the well done stage without excessive

browning.

• Most foods should be turned halfway through broiling

time.

15

Oven Cooking

Keep Warm

For safely keeping hot foods warm or for warming breads and

plates.

To set Keep Warm:

1. Press the appropriate Keep Warm pad.

• WARM flashes.

• 000 and either UPPER or LOWER flash

in the display.

2. Select the Keep Warm temperature. Press the

Autoset pad or the appropriate number pads.

• 170° will light when the Autoset pad is pressed.

• Each press of the Autoset pad will increase the

temperature by 5°.

The Keep Warm temperature can be set from 145° to 190°.

WARM and the temperature will be displayed while the

function is active.

Keep Warm Notes:

• For optimal food quality, oven cooked foods should be

kept warm for no longer than 1 to 2 hours.

• To keep foods from drying, cover loosely with foil or a lid.

• To warm dinner rolls:

- cover rolls loosely with foil and place in oven.

- press Keep Warm and Autoset pads.

- warm for 12-15 minutes.

• To warm plates:

- place 2 stacks of up to four plates each in the oven.

- press Keep Warm and Autoset pads.

- warm for 5 minutes, turn off the oven and leave

plates in the oven for 15 minutes more.

- use only oven-safe plates, check with the

manufacturer.

- do not set warm dishes on a cold surface as rapid

temperature changes could cause crazing or

breakage.

To cancel Keep Warm:

1. Press the CANCEL pad.

2. Remove food from the oven.

Favorite

The Favorite pad allows you to save the time and temperature

from a Cook & Hold Bake, Cook & Hold Convect Bake or Cook

& Hold Convect Roast (lower oven only) operation.

To set a Favorite setting, a Cook & Hold function must be

either active or just programmed.

To set a new Favorite operation or to save a

currently running Cook & Hold as a Favorite:

1. Program a Cook & Hold setting as described in the Cook &

Hold section on page 12.

2. Press and hold the Favorite pad for three

seconds.

• The newly set or currently running Cook & Hold setting

will be saved.

• A double then a single beep will sound to indicate that

the control has accepted the Favorite setting.

To start a cycle programmed into Favorite:

1. Press the Favorite pad.

• Time and temperature for the set Cook & Hold setting

will be displayed. (If no Cook & Hold setting has been

programmed, “nonE” is displayed.)

2. Press the Bake, Convect Bake or Convect Roast (lower

oven only) pad.

• The Favorite setting will begin immediately.

• The selected function will light in the display

• The cooking time will light in the display

When the cooking time has elapsed:

• The selected function will turn off.

• WARM HOLD will light.

• 170° will display.

To cancel a Favorite setting in progress:

1. Press the CANCEL pad.

2. Remove food from the oven.

• The stored Favorite setting will not be

affected.

16

Oven Cooking

Automatic Shut-Off/Sabbath

Mode

The ovens will automatically turn off after 12 hours if you

accidentally leave them on.

To cancel the 12-hour shut-off and run an

oven continuously for 72 hours:

1. Press and hold the Clock pad for three seconds

• “SAb” will be displayed and flash for five seconds.

• “SAb” will then be displayed continuously until turned

off or until the 72-hour time limit is reached.

• BAKE will also be displayed if a bake setting is in use

while the oven is in Sabbath Mode.

• All pads are inactive except CANCEL and Clock. All

other functions EXCEPT BAKE (Timer, Keep Warm,

Clean, etc.) are locked out during the Sabbath Mode.

To cancel the Sabbath Mode:

1. Press the CLOCK pad for three seconds.

• “SAb” will flash for five seconds.

• The time of day will return to the display.

OR

2. After 72 hours, the Sabbath Mode will end.

• “SAb” will flash for five seconds.

• The time of day will return to the display.

Adjusting the Oven Temperature

Oven temperatures are carefully tested for accuracy at the

factory. It is normal to notice some baking or browning

differences between a new oven and an old one. As ovens

get older, the oven temperature can shift.

You may adjust the oven temperature if you think the oven is

not baking or browning correctly. To decide how much to

change the temperature, set the temperature 25 degrees

higher or lower than your recipe recommends, then bake.

The results of the first bake should give you an idea of how

much to adjust the temperature.

To adjust the oven temperature:

1. Press the appropriate Bake pad.

2. Enter 550° by pressing the appropriate number pads.

3. Press and hold the Bake pad for several seconds or until

00° appears in the display.

If the oven temperature was previously adjusted, the

change will be displayed. For example, if the oven tem-

perature was reduced by 15° the display will show “-15°”.

4. Press the Autoset pad to adjust the temperature.

Each time the Autoset pad is pressed, the temperature

changes by 5°. The oven temperature can be increased or

decreased by 5° to 35°.

5. The time of day will automatically reappear in the display.

You do not need to readjust the oven temperature if there is a

power failure or interruption. Temperature adjustment applies

to Bake, Convect Bake and Convect Roast (lower oven only)

only.

Sabbath Mode Notes:

• Sabbath Mode can be turned on at any time with or

without the ovens on.

• Sabbath Mode cannot be turned on if the keypads are

locked out or when the doors are locked.

• Most prompts and messages and all beeps are

deactivated when Sabbath Mode is active.

• If an oven is baking when Sabbath Mode is set, BAKE

will go out at the end of the baking cycle or when the

CANCEL pad is pressed. There will be no audible beeps.

• If the oven lights are desired while in Sabbath Mode,

they must be turned on before the Sabbath Mode is

started.

• When the Sabbath Mode is started, the temperature

display will immediately show the set temperature, rather

than the actual oven cavity temperature. No preheat beep

will sound.

• The self-clean cycle and automatic door lock do not

operate during the Sabbath Mode.

• Pressing CANCEL pad will cancel a Bake cycle, however

the control will stay in the Sabbath Mode.

• If power fails, the ovens will power up in Sabbath Mode

with 72 hours remaining and no cycle active.

17

Oven Cooking

Oven Lights

The oven lights automatically come on whenever

an oven door is opened. When the door is closed,

press the Oven Light pad to turn the oven light

on or off. A beep will sound every time the Oven

Light pad is pressed.

Oven Bottom

Protect oven bottom against spillovers, especially acidic or

sugary spills, as they may discolor the porcelain enamel. Use

the correct pan size to avoid spillovers and boilovers. Do not

place utensils or aluminum foil directly on the oven

bottom.

Oven Vent

When the oven is in use the area near the vent may become

hot enough to cause burns. Never block the vent opening.

The oven vent is located below the backguard on your

range.

When high moisture foods are cooked in the upper oven,

steam may be visible coming from the oven vent. This is

normal.

CAUTION

Oven Racks

• Do not attempt to change the rack position when the oven

is hot.

• Do not use the oven for storing food or cookware.

OVEN VENT

LOCATION

Do not place

plastics near the

vent opening as

heat from the vent

could distort or

melt the plastic.

All racks are designed with a lock-stop edge.

Upper oven

• Is equipped with one rack and rack

position.

• When pulling the upper oven rack out to

remove or check food, grasp the top edge

of the rack.

Lower oven

• Is equipped with one RollerGlide

TM

rack and two regular flat

racks.

To remove oven racks:

• Pull rack straight out until it stops at the lock-stop position;

lift up on the front of the rack and pull out.

• For RollerGlide

TM

rack, pull both the rack glide and rack

base out together.

To replace oven racks:

• Place rack on the rack support in

the oven; tilt the front end up

slightly; slide rack back until it

clears the lock-stop position; lower

front and slide back into the oven.

Baking and Roasting with the

RollerGlide

TM

Rack (lower oven only)

Baking

• For optimal baking results when baking on one rack, use

the RollerGlide

TM

rack.

• When baking on two racks, use the RollerGlide

TM

rack in

the bottom rack position, and the flat rack in the upper rack

position.

Roasting

• When roasting large cuts of meat and poultry, use the

RollerGlide

TM

rack for ease of movement.

Oven Fan

A convection fan is used to circulate hot air in the oven when

the convection feature is selected. It automatically turns on

after the Convect Bake or Convect Roast pads are pressed

and will turn off when convection is canceled.

Note: The convection fans will automatically stop when

the oven door is opened.

18

Oven Cooking

Rack Positions (lower oven)

5

4

3

2

1

RACK 5: Use for toasting bread or broiling very thin foods

and two-rack baking.

RACK 4: Use for two-rack baking and for broiling.

RACK 3: Use for most baked goods on a cookie sheet or jelly

roll pan, layer cakes, fruit pies, or frozen convenience foods

and for broiling.

RACK 2: Use for roasting small cuts of meat, casseroles,

baking loaves of bread, bundt cakes or custard pies and two-

rack baking.

RACK 1: Use for roasting large cuts of meat and poultry,

frozen pies, dessert souffles or angel food cake and two-rack

baking.

MULTIPLE RACK COOKING:

Two rack: Use rack positions 2 and 4, 1 and 4 or 2 and 5.

Three rack: Userack positions 1, 3 and 5. See illustration

above.

Half Rack Accessory

(Lower oven only)

A half rack, to increase oven capacity, is available as an

accessory. It fits in the left, upper portion of the lower oven

and provides space for a vegetable dish when a large roaster

is on the lower rack. Contact your Maytag dealer for the

“HALFRACK” Accessory Kit or call 1-877-232-6771 USA or

1-800-688-8408 Canada to order.

Baking Layer Cakes on Two Racks

For best results when baking cakes on two racks, use racks 2

and 4.

Place the cakes on the rack as shown.

19

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

Self-Clean Ovens

CAUTION

• It is normal for parts of the ovens to become hot during a

self-clean cycle.

• To prevent damage to oven doors, do not attempt to open

the doors when LOCK is displayed.

• Avoid touching doors, windows or oven vent area during

a clean cycle.

• Do not use commercial oven cleaners on the oven finish

or around any part of the ovens. They will damage the

finish or parts.

• Do not leave baking/pizza stone in the oven during

self-clean.

The self-clean cycle uses above-normal cooking temperatures

to automatically clean the oven interior.

The oven should be cleaned regularly by wiping up spillovers

to prevent excessive smoke and flare-ups. Do not allow a

heavy build-up of soil to accumulate in the oven.

During the cleaning process, the kitchen should be well

ventilated to get rid of normal odors associated with cleaning.

Before Self-Cleaning

1. Turn off the oven light before cleaning as the light may

burn out during the clean cycle.

2. Remove broiler pan, all pans, and oven racks from the

oven. The oven racks will discolor and may not slide easily

after a self-clean cycle if they are not removed.

3. Clean oven frame, door frame (area outside of gasket, and

around the opening in the door gasket) with a nonabrasive

cleaner such as Bon Ami* or detergent and water. The

self-cleaning process does not clean these areas. They

should be cleaned to prevent soil

from baking on during the clean

cycle. (The gasket is the seal

around the oven door and window.)

4. To prevent damage, do not clean or

rub the gasket around the oven

door. The gasket is designed to seal in heat during the

clean cycle.

5. Wipe up excess grease or spillovers from the oven bottom.

This prevents excessive smoking, flare-ups or flaming

during the clean cycle.

6. Wipe up sugary and acidic spillovers such as sweet

potatoes, tomato, or milk-based sauces. Porcelain enamel

is acid-resistant, not acid-proof. The porcelain finish may

discolor if acidic or sugary spills are not wiped up before a

self-clean cycle.

Notes:

• Oven temperature must be below 400° F to program a

clean cycle.

• Only one oven can be cleaned at a time.

• Both oven doors lock when either oven is being

cleaned.

To set Self-Clean:

1. Close the oven door.

2. Press the Clean pad.

• CLEAN flashes.

• SET and UPPER or LOWER flash in the

display.

3. Press the Autoset pad.

• “MEd” (Medium Soil, 3 hours) is displayed.

4. Press the Autoset pad to scroll through the self-cleaning

settings.

“HVy” (Heavy Soil, 4 hours)

“MEd” (Medium soil, 3 hours)

“LITE” ( Light Soil, 2 hours)

Choosing the soil level of the oven automatically programs

the self-cleaning time.

5. After four seconds, the oven will start cleaning.

• If the door is not closed, beeps will sound and ‘door’ will

display. If the door is not closed within 30 seconds, the

self-cleaning operation will be canceled and the display

will return to the time of day.

• CLEAN will appear in the display.

• LOCK will flash in the display. Once the door locks,

LOCK will remain steady.

• The cleaning time will start counting down in the

display.

To Delay a Self-Clean Cycle:

1. Press the Delay pad once for upper oven and

twice for lower oven.

• DELAY flashes.

• 00:00 and UPPER or LOWER will flash in the display.

2. Enter the amount of time you want to delay the cycle

using the appropriate number pads.

3. Press the appropriate Clean pad.

• SET flashes in the display.

Care & Cleaning

La page charge ...

Maytag MER6875AA Mode d'emploi

Maytag MER6875AA Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents