Dometic MPC01 Guide d'installation

MPC01

Battery Management System

Installation and Operating Manual . . . . . . 7

Batteriemanagementsystem

Montage- und Bedienungsanleitung . . . 25

Système de gestion des batteries

Instructions de montage

et de service . . . . . . . . . . . . . . . . . . . . . . . 43

Sistema de gestión de baterías

Instrucciones de montaje y de uso . . . . . 60

Sistema de gestão de baterias

Instruções de montagem e manual de

instruções . . . . . . . . . . . . . . . . . . . . . . . . . 77

Sistema di gestione batterie

Istruzioni di montaggio e d’uso . . . . . . . . 94

Accumanagementsysteem

Montagehandleiding en

gebruiksaanwijzing. . . . . . . . . . . . . . . . . 112

Batterimanagementsystem

Monterings- og betjeningsvejledning. . 129

Batterihanteringssystem

Monterings- och bruksanvisning . . . . . . 146

Batteristyringssystem

Monterings- og bruksanvisning . . . . . . . 163

Akkuhallintajärjestelmä

Asennus- ja käyttöohje. . . . . . . . . . . . . . 180

Система управления батареями

Инструкция по монтажу

и эксплуатации. . . . . . . . . . . . . . . . . . . . 197

Układ zarządzania akumulatorami

Instrukcja montażu i obsługi . . . . . . . . . 215

Systém manažmentu batérií

Návod na montáž a uvedenie

do prevádzky . . . . . . . . . . . . . . . . . . . . . 232

Systém řízení a sledování stavu

akumulátoru

Návod k montáži a obsluze . . . . . . . . . . 249

Akkumulátorkezelő rendszer

Szerelési és használati útmutató . . . . . . 266

EN

DE

FR

ES

PT

IT

NL

DA

SV

NO

FI

RU

PL

SK

CS

HU

ENERGY & LIGHTING

MPC

MPC01-IO-16s.book Seite 1 Mittwoch, 3. August 2016 4:46 16

MPC01-IO-16s.book Seite 2 Mittwoch, 3. August 2016 4:46 16

MPC01

3

1

2 43

5

6

9 10

8

11

12

7

1

2

MPC01-IO-16s.book Seite 3 Mittwoch, 3. August 2016 4:46 16

MPC01

4

1

JUMP

3

AB

1 1

4

MPC01-IO-16s.book Seite 4 Mittwoch, 3. August 2016 4:46 16

MPC01

5

1

3

4

5

2

10

9

8

7

6

2a

2b

3a

3b

5

1

6

MPC01-IO-16s.book Seite 5 Mittwoch, 3. August 2016 4:46 16

MPC01

6

1

7

2 1

8

MPC01-IO-16s.book Seite 6 Mittwoch, 3. August 2016 4:46 16

MPC01 Explanation of symbols

EN

7

Please read this instruction manual carefully before installation and first use, and store

it in a safe place. If you pass on the product to another person, hand over this instruc-

tion manual along with it.

Contents

1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2 Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

5 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7 Connecting and installing MPC01. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

8 Operating the MPC01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

9 Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

10 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

11 Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

1 Explanation of symbols

!

A

I

WARNING!

Safety instruction: Failure to observe this instruction can cause fatal or serious injury.

CAUTION!

Safety instruction: Failure to observe this instruction can lead to injury.

NOTICE!

Failure to observe this instruction can cause material damage and impair the function

of the product.

NOTE

Supplementary information for operating the product.

MPC01-IO-16s.book Seite 7 Mittwoch, 3. August 2016 4:46 16

Safety instructions MPC01

EN

8

2 Safety instructions

The manufacturer accepts no liability for damage in the following cases:

• Damage to the product resulting from mechanical influences and excess voltage

• Alterations to the product without express permission from the manufacturer

• Use for purposes other than those described in the operating manual

Please observe the following basic safety information when using electrical devices to prevent:

• Electric shock

• Fire hazards

• Injury

!

WARNING!

• Electrical devices are not toys!

Always keep and use the device out of the reach of children.

• People (including children) whose physical, sensory or mental capacities or whose

lack of experience or knowledge prevent them from using this product safely should

not use it without the supervision or instruction of a responsible person.

• Only use the device as intended.

• Make sure that the lead has a sufficient cross-section.

• Lay the cables so that they cannot be damaged by the doors or the bonnet. Crushed

cables can lead to serious injury.

!

CAUTION!

• Lay the cables so that they cannot be tripped over or damaged.

• Do not operate the device

– In salty, wet or damp environments

– In the vicinity of corrosive fumes

– In areas where there is a danger of explosions.

• Always disconnect the power supply when working on the device.

• Please observe that parts of the device may still conduct voltage even if the fuse has

blown.

• Do not disconnect any cables when the device is still in use.

A

NOTICE!

• Use ductwork or cable ducts if it is necessary to lay cables through metal panels or

other panels with sharp edges.

• Do not lay the cable so that it is loose or heavily kinked.

• Fasten the cables securely.

• Do not pull on the cables.

MPC01-IO-16s.book Seite 8 Mittwoch, 3. August 2016 4:46 16

MPC01 Scope of delivery

EN

9

3Scope of delivery

4 Accessories

Available as accessories (not included in the scope of delivery):

No. in

fig. 1,

page 3

Quantity Designation

1 1 Adapter board and cover

21Cover frame

31Display

4 1 Assembly frame

5 1 Battery sensor (MCA-HS1 Hella sensor)

6 1 Battery sensor connection cable

7 1 Charging unit connection cable

81Control cable

9 1 Control cable connected mass (black)

10 1 Control cable positive pole (red)

11 4 Screws, long

12 4 Screws, short

Designation Ref. no.

Battery sensor, MCA-HS1 Hella sensor 9102500038

MPC01-IO-16s.book Seite 9 Mittwoch, 3. August 2016 4:46 16

Intended use MPC01

EN

10

5Intended use

MPC01 (ref. no. 9102500073) is a battery management system which allows the battery charge

status of several batteries to be monitored. MPC01 may only be operated with PerfectCharge

MCA chargers.

The device is designed for use in caravans and boats.

6 Technical description

6.1 Function

The current status information for each battery connected via a battery sensor appears on the

display: current, voltage, temperature, remaining charge time and remaining capacity (in %) of all

batteries connected.

Included with the MPC01 is one battery sensor for connecting one battery. To connect more

batteries you need additional battery sensors (ref. no. 9102500038) (accessories).

MPC01 enables the charge status of the starter battery and up to three supply batteries to be

monitored. To do so, the battery sensors are connected to the negative pole of the batteries. The

information read out from them is transmitted to the display via the CI bus interface. The battery

sensors measure the voltage, current and temperature of the connected battery. Along with the

battery sensor supplied, up to three more battery sensors (accessories) can be connected.

MPC01 features three programmable outputs for switching off consumers should the battery

capacity be too low (battery monitor function).

The battery charger is connected to the display via the CI bus interface.

MPC01 features a display mode, and a stand-by mode which is activated after a preset interval.

A programmable alarm function reminds the user of the preset time.

A jumper allows the operating mode to be changed from “caravan” to “boat”.

6.2 Display and control elements

No. in

fig. 2,

page 3

Designation Explanation

1Display Shows values

2 Selector button Tu rn : Navigate through menus or change values

Press: Select menu items or values

MPC01-IO-16s.book Seite 10 Mittwoch, 3. August 2016 4:46 16

MPC01 Connecting and installing MPC01

EN

11

7 Connecting and installing MPC01

7.1 Notes on installation

When selecting the installation location for the display and adapter board, observe the following

instructions:

• The device must be installed in a location that is protected from moisture.

• Do not install the device in a dusty environment.

• The device must be installed on a level and sufficiently sturdy surface.

• Ensure the control cable is 6 m long.

• Install the adapter board in a well-protected location, close to the batteries if possible, to ensure

no objects can touch the connection cable and cause it to tear.

7.2 Changing the operating mode

The operating mode is set using the jumper (fig. 3 1, page 4). The jumper is already plugged in

when the device is delivered, and set to the “caravan” operating mode.

➤ To set the “boat” operating mode: Remove the jumper (fig. 3 1, page 4).

7.3 Connecting and installing the display

You can install the MPC01 on the wall or in the wall. For installation on the wall, the control cable

can either be guided through the wall or affixed on the wall.

Installing the display on a wall (fig. 4 A, page 4)

➤ Plug the control cable (1) into the connection on the display.

➤ Guide the control cablethrough the slot in the installation frame.

➤ Place the display in the installation frame.

➤ Affix the installation frame and display insert onto a suitable part of the wall using the four long

screws supplied.

➤ Attach the cover frame so that it latches into place.

Installing the display in a wall (fig. 4 A, page 4)

➤ Prepare a recess in the wall measuring 11 x 9.9 cm and which is 2.5 cm in depth.

➤ Plug the control cable (fig. 1 8, page 3) into the connection on the display.

➤ Affix the display (fig. 1 3, page 3) using the four short screws supplied (fig. 1 12, page 3).

➤ Attach the cover frame (fig. 1 2, page 3) so that it latches into place.

MPC01-IO-16s.book Seite 11 Mittwoch, 3. August 2016 4:46 16

Connecting and installing MPC01 MPC01

EN

12

7.4 Connecting and installing the adapter board

➤ Screw the cover and the adapter board in place at a suitable location using two screws.

➤ Secure the connected cables using suitable fittings, e.g. cable clamps, to ensure the plug

cannot be torn from the circuit board.

I

➤ Depending on the number of supply batteries connected, assign the connections as follows:

–Connecting one supply battery: IBS_B2A (fig. 5 10, page 5)

–Connecting two supply batteries: IBS_B2A (fig. 5 10, page 5) and IBS_B2B (fig. 5 7,

page 5)

–Connecting three supply batteries: IBS_B2A (fig. 5 10, page 5), IBS_B2B (fig. 5 7,

page 5) and IBS_B2C (fig. 5 9, page 5)

➤ Connect the connection cables as follows:

NOTE

• Supply battery A must be connected to the IBS-B2A connection for the MPC01 to

be able to display data.

• Up to three supply batteries (IBS_B2A, IBS_B2B and IBS_B2C) and a starter battery

(IBS_B1) can be connected.

No. in

fig. 5,

page 5

Designation Explanation

1 OUT 1 Switchable output 1 for consumer units

2 OUT 3 Switchable output 3 for consumer units

2a: +12 V

2b: connected mass

3 Voltage supply connection

3a: +12 V

3b: connected mass

4 Connection for MSK, MSI and MSP series inverters

5 OUT 2 Switchable output 2 for consumer units

6Connection for display

7 IBS_B2B Connection for supply battery B

8 IBS_B1 Connection for starter battery

9 IBS_B2C Connection for supply battery C

10 IBS_B2A CI bus Connection for supply battery A, charger unit

MPC01-IO-16s.book Seite 12 Mittwoch, 3. August 2016 4:46 16

MPC01 Connecting and installing MPC01

EN

13

Connecting the battery sensor

In “boat” and “caravan” operating modes, the supply batteries A, B and C can be connected in

addition to the starter battery.

In “boat” operating mode, the battery connection IBS_B2C is not factored into the calculation of

the total current and voltage shown in “Supply batteries overview”. As a rule, the battery sensor for

the sideshift bow thruster should be plugged into battery connection IBS_B2C.

➤ Connect the battery sensor connection cable (fig. 1 6, page 3) to the battery sensor

(fig. 1 5, page 3).

➤ Connect the battery sensor to the negative pole of the battery.

➤ Clamp the blue cable of the connection cable of the battery sensor (fig. 1 6, page 3) onto the

positive pole of the battery (voltage supply).

➤ Plug the red cable with the white plug connection onto the corresponding CI bus connection

on the adapter board (fig. 5 6–10, page 5).

Calibrating the battery sensor

I

To calibrate the sensor to the charge level of the connected battery, proceed as follows:

➤ Connect a high current load (20 – 30 A) to the battery for a time of 3 to 5 minutes.

➤ Repeat this 2 or 3 times.

➤ Disconnect the load.

➤ Allow the battery sensor some time to calibrate itself (battery current < 100 mA)

I

If you want to reset the calibration data of the sensor, disconnect the sensor's power supply.

Connecting the MPC01 to the voltage supply

➤ Plug the cable lug end of the red cable (fig. 1 10, page 3) onto the left contact of the voltage

supply connection of the adapter board (fig. 5 3a, page 5).

➤ Connect the end of the red cable with the round cable lug to the positive battery pole.

➤ Plug the cable lug end of the black cable (fig. 1 9, page 3) onto the right contact of the volt-

age supply connection of the adapter board (fig. 5 3b, page 5).

➤ Connect the cable lug eye of the black cable to the consumer unit connection contact of the

battery sensor on a negative battery pole (fig. 6 1, page 5).

Connecting power consuming devices to the battery sensor

➤ Always connect the negative pole of the power consuming devices to the correct connection

on the battery sensor (fig. 6 1, page 5).

NOTE

The battery sensor has to be calibrated anew, if

• the battery sensor is disconnected

• the battery sensor’s power supply is disconnected

NOTE

The battery sensor requires a rest period of approximately 8 hours for calibration.

MPC01-IO-16s.book Seite 13 Mittwoch, 3. August 2016 4:46 16

Operating the MPC01 MPC01

EN

14

8 Operating the MPC01

Navigating within the menu

Navigate through the menus as follows:

➤ Turn the selector button (fig. 2 2, page 3) to scroll through the individual pages in the menu

or through the items appearing on one page of the menu.

➤ Press the selector button to access the sub-menus or change mode.

➤ Turn the selector button until the message “Press to return” appears and then press the

selector button.

✓ This will return you to the “Main menu”.

The following four figures show how you can navigate within the menu.

MPC01-IO-16s.book Seite 14 Mittwoch, 3. August 2016 4:46 16

MPC01 Operating the MPC01

EN

15

Main menu

System

settings menu

Battery

details menu

Charger

Starter/motor battery

Overview of

supply batteries

Start

Inverter

MPC01-IO-16s.book Seite 15 Mittwoch, 3. August 2016 4:46 16

Operating the MPC01 MPC01

EN

16

System settings menu

Change

settings

Back

Settings

Main menu

Stand-by

settings

Change

settings

MPC01-IO-16s.book Seite 16 Mittwoch, 3. August 2016 4:46 16

MPC01 Operating the MPC01

EN

17

Battery details

Battery

parameters/

switches menu

Battery history

Back

Supply battery C

(“Caravan” operating mode only)

Supply battery B

Supply battery A

Main menu

MPC01-IO-16s.book Seite 17 Mittwoch, 3. August 2016 4:46 16

Operating the MPC01 MPC01

EN

18

Battery parameters/switches menu

Battery

settings

Change

settings

Change

settings

Switchable

output settings

Back

Main menu

MPC01-IO-16s.book Seite 18 Mittwoch, 3. August 2016 4:46 16

MPC01 Operating the MPC01

EN

19

Display symbols

Symbol Explanation

Caravan starter battery

Caravan supply battery

Boat starter battery

Boat supply battery

Battery is charging

Battery is being discharged by the consumer units connected

S Summary of all battery values

A Supply battery A

B Supply battery B

C Supply battery C

M Starter battery

U Operating voltage

MPC01-IO-16s.book Seite 19 Mittwoch, 3. August 2016 4:46 16

Operating the MPC01 MPC01

EN

20

I Positive value: Battery is charging

Negative value: Battery is discharging

Fan activated

Charger 1 connected

Battery history

When battery is charging: remaining charge time

When battery is discharging: remaining usage time

Charge capacity in percent

Battery temperature. This is only shown on the “Detailed view” menu

pages for the individual batteries.

Date, Time, Alarm

Alarm On

Alarm Off

Symbol Explanation

MPC01-IO-16s.book Seite 20 Mittwoch, 3. August 2016 4:46 16

La page charge ...

Dometic MPC01 Guide d'installation

Dometic MPC01 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents