Maytag MFD2562VEA10 Le manuel du propriétaire

Marque: Maytag

Modèle: MFD2562VEA10

Catégorie: Frigos

Taper: Le manuel du propriétaire

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,

please visit our website at www.maytag.com for additional information. If you still need assistance, call us at 1-800-688-9900.

In Canada, visit our website at www.maytag.ca or call us at 1-800-807-6777.

You will need your model and serial number located on the inside wall of the refrigerator compartment.

Para obtener acceso a "lnstrucciones para el usuario del refrigerador" en espa_ol, o paraobtener informaci6n adicional acerca de

su producto, visite: www.maytag.com.

Tenga listo su nQmero de modelo completo. Puede encontrar su nQmero de modelo y de serie en la etiqueta ubicada al lado

derecho del interior del refrigerador.

Table of Contents / Table des rnati res

REFRIGERATOR SAFETY ........................................................ 1

INSTALLATION INSTRUCTIONS ............................................. 2

REFRIGERATOR USE............................................................. 12

REFRIGERATOR CARE .......................................................... 16

TROUBLESHOOTING ............................................................. 17

WATER FILTER CERTIFICATIONS ....................................... 19

PRODUCT DATA SHEETS ..................................................... 20

SI_CURITI_ DU RI_FRIGI_RATEUR ......................................... 22

INSTRUCTIONS D'INSTALLATION ....................................... 23

UTILISATION DU REFRIGERATEUR .................................... 33

ENTRETIEN DU RI:!:FRIGI:!:RATEUR....................................... 37

DEPAN NAGE ........................................................................... 39

FEUlLLES DE DONNI:!:ESSUR LE PRODUlT ....................... 42

GARANTIE ............................................................................... 43

WARRANTY ............................................................................. 21

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

W10175446A

iMPORTANT SAFETY iNSTRUCTiONS

WARNING:To reduce the risk of fire, electric shock, or injuryto persons when using the refrigerator, follow basic precautions,

including the following:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

[] Use nonflammable cleaner.

[] Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

[] Use two or more people to move and install refrigerator.

[] Disconnect power before installing ice maker (on ice maker

kit ready models only).

SAVETHESEINSTRUCTIONS

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Takeoff the doors.

• Leave the shelves in place so that children may not easily

climb inside.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

• Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

• Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

• Dispose of/recycle all packaging materials.

When Moving "{our Refrigerator:

Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pull the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in "Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a V2"

(1.25 cm) space at the top and behind the refrigerator. If your

refrigerator has an ice maker, allow extra space at the back for

the water line connections. When installing your refrigerator next

to a fixed wall, leave 2V2"(6.3 cm) minimum on the hinge side

(some models require more) to allow for the door to swing open.

NOTE: It is recommended that you do not install the refrigerator

near an oven, radiator, or other heat source. Do not install the

refrigerator in a location where the temperature will fall below

55°F (13°C).

2_/2'' (6.'3era)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an extension

cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the refrigerator to OFF. Depending on

your model, turn the freezer control to the word OFF, or press the

Freezer down arrow touch pad until a dash (-) appears in both the

Freezer and Refrigerator displays as shown. Disconnect the

refrigerator from the electrical source. When you are finished,

reconnect the refrigerator to the electrical source and reset the

temperature controls to the desired setting. See "Using the

Controls."

....................,,_,_,?_ _ _

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • V4"Nut driver

• 7/le"and V2"Open-end or two • V4"Drill bit

adjustable wrenches • Cordless drill

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Do not use a piercing-type or 3/le"(4.76 mm) saddle valve

which reduces water flow and clogs more easily.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Water Pressure

A cold water supply with water pressure of between 35 and

120 psi (241 and 827 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your water

pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

• If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water

Filtration System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

Read all directions before you begin.

IMPORTANT: Ifyou turn the refrigerator on before the water line

is connected, turn the ice maker OFE

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Find a V2"to 1V4" (12.7 mm to 31.8 mm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure

from the connection on the rear of the refrigerator to the

water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use V4"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

Using a cordless drill, drill a V4"hole in the cold water pipe

you have selected.

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E.Compression sleeve

F. Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the V4"drilled hole

in the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws

slowly and evenly so the washer makes a watertight seal. Do

not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and

turn ON the main water supply. Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe.

Connect to Refrigerator

Depending on your model, the water line may come down from

the top or up from the bottom. Follow the connection instructions

for your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the

copper tube to the valve inlet using a compression nut and

sleeve as shown. Tighten the compression nut. Do not

overtighten. Confirm copper tubing is secure by pulling on

copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a "P" clamp.

A. Copper tubing D. Compression sleeve

B. "P" clamp E. Water valve inlet port

C. Compression nut

Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

Style 2

1. Create a service loop (minimum diameter of 2 ft [61 cm]) with

the copper tubing. Avoid kinks when coiling the copper

tubing.

2. Remove the plastic cap from water valve inlet port. Place a

compression nut and sleeve on the copper tubing.

3. Insert the end of the copper tubing into the water valve inlet

port. Shape tubing slightly so that the tubing feeds straight

into the port to avoid kinks.

4. Slide the compression nut over the sleeve and screw into the

water valve inlet port.

A. Plastic water tubing C. Compression nut

B. Sleeve D. Copper tubing

Using an adjustable wrench, hold the nut on the plastic water

line to keep it from moving. Then, with a second wrench turn

the compression nut on the copper tubing counterclockwise

to completely tighten. Do not overtighten.

A. Plastic water line

B. Water valve inlet port

C. Compression nut

D. Copper tubing

E. "P" clamp

Check connection by pulling on copper tubing. Attach copper

tubing to refrigerator cabinet with a "P" clamp. Turn on water

supply to refrigerator and check for leaks. Correct any leaks.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill the ice container.

Rc' __o_ Doo_t5} a_ D_a_we_ _

TOOLS NEEDED: %e", 3/8",V4"hex-head socket wrench, a

#2 Phillips screwdriver, and a flat-blade screwdriver.

IMPORTANT:

• Your refrigerator may have a standard reversible refrigerator

door (Style 1) with either a freezer door or freezer drawer, or

French doors (Style 2). Follow the instructions specific to the

door style of your model.

• All graphics referenced in the following instructions are

included later in this section after "Final Steps." The graphics

shown for the standard door (Style 1) are for a right-hand

swing refrigerator (hinges factory installed on the right).

• If you only want to remove and replace the doors, see

"Remove Doors and Hinges" and "Replace Doors and

Hinges."

• Before you begin, turn the refrigerator control OFF, and

remove food and adjustable door or utility bins from the

doors.

Remove and Replace Refrigerator Door Handles

Style 1-Standard Door

Front Mount Handle

• To remove the handle, remove the screw attaching the trim to

the upper end of the handle. Using a flat-blade screw driver

wrapped in masking tape, pry the trim piece from the lower

end of the handle. Then, remove the screws attaching the

handle to the door. See Front Mount graphic 2.

Remove Door and Hinges

Style 1-Standard Door

_" Hex-Head TopHinge Screw

Freezer drawer models

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator door closed until you are ready to lift it

free from the cabinet.

NOTE: Provide additional support for the door while the

hinges are being moved. Do not depend on the door gasket

magnets to hold the door in place while you are working.

3. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the refrigerator door free from the cabinet.

4. Remove the parts for the bottom hinge as shown in Bottom

Hinge graphic.

Freezer door models

1. Unplug refrigerator or disconnect power.

2. Keep the freezer door closed until you are ready to lift it free

from the cabinet.

NOTE: Provide additional support for the door while the

hinges are being moved. Do not depend on the door gasket

magnets to hold the door in place while you are working.

• To replace handle, reverse directions.

Side Mount Handle

• To remove the handle, remove the four screws attaching the

handle to the side of the door. See Side Mount graphic 2.

• To replace the handle, align the holes in the handle with the

holes in the door. Then, insert a screw in the upper hole at

each end of the handle. Next, insert a screw in the lower

holes. Tighten the screws. See Side Mount graphic 2.

Style 2-French Doors

Metal Handles

• Using a 3/32"Allen wrench, loosen the two set screws located

on the side of each handle. Pull the handle straight out from

the door. Make sure you keep the screws for reattaching the

handles. See Metal Handle graphic 1.

• To replace the handles, reverse the directions.

Plastic Handles

• To remove the handle, grasp the lower part of the handle

firmly, slide the handle up and pull the handle straight out

from the door. See Plastic Handle graphic 1.

• To replace the handle, position the handle so that the large

holes in the mounting clips are down and align the holes with

the door studs. Rotate the handle so that the mounting clips

are flat against the door and slide the handle down to

engage. See Plastic Handle graphic 1.

3. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the refrigerator door free from the cabinet.

4. Remove the center hinge pin and remove the hinge screws as

shown in the Center Hinge graphic. Lift the freezer door free

from the cabinet.

5. Remove the parts for the bottom hinge as shown in Bottom

Hinge graphic.

Style 2-French Doors

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

3. Starting with the right-hand side door, remove the parts for

the top hinge as shown in Top Hinge graphic. Lift the

refrigerator door from the bottom hinge pin.

4. Remove the shim (on some models) from the bottom hinge

pin and keep it for later use. See Bottom Hinge graphic.

5. Before removing the left-hand side door, disconnect the

wiring plug located on top of the top hinge by wedging a flat-

blade screwdriver or your fingernail between the two

sections. See Wiring Plug graphic.

NOTE: The green, ground wire remains attached to the hinge.

6. Remove the parts for the left-hand side door top hinge as

shown in the Top Hinge graphic. Lift the door from the bottom

hinge pin.

NOTE: On some models, remove the shim from the bottom

hinge pin and keep it for later use. See Bottom Hinge graphic.

Reverse Door - Standard Door (optional)

IMPORTANT: Ifyou want to reverse your door so it opens from

the opposite side, follow these steps. If you are not reversing the

door, see "Replace Door and Hinges."

DoorStop Screw Door Handle Seal Screw Front

Flat-Head Handle Screw Cabinet Hinge HolePlug

Cabinet

1. Remove hinge screws from handle side and move them to

opposite side. See Graphic 1-1.

2. Remove cabinet hinge hole plugs from cabinet top and move

them to opposite side hinge holes as shown in Graphic 1-2.

Refrigerator door

1. Remove the refrigerator handle assembly as shown in

Graphic 2. Keep all parts together.

2. Remove door handle seal screw front. Move to opposite side

of refrigerator door as shown in Graphic 6.

3. Remove the door stop. Move it to the opposite side of the

refrigerator door as shown in Graphic 4.

4. Attach the refrigerator handle to the opposite side of the

refrigerator door.

NOTE: For models with Front mount handles, replace the

handle trim as shown in Graphic 2.

5. Tighten all screws. Set aside the door until hinges and freezer

compartment door or drawer are in place.

Freezer door

1. Remove freezer handle assembly as shown. Keep all parts

together. See Graphic 5-1.

2. Remove freezer door handle seal screw. Move to opposite

side of freezer door.

3. Remove door stop. Move to opposite side of freezer door as

shown. See Graphic 4.

4. Attach handle to opposite side of freezer door.

5. Tighten all screws. Set aside door until bottom hinge is

installed on product.

Replace Door and Hinges

Style 1-Standard Door

NOTE: Graphics may be reversed if door swing is reversed.

Freezer drawer models

1. Replace the parts for the bottom hinge as shown. Tighten

screws.

NOTE: Provide additional support for the door while the

hinges are being moved. Do not depend on the door gasket

magnets to hold the door in place while you are working.

2. Assemble the parts for the top hinge as shown in Top Hinge

graphic. Do not tighten screws completely.

3. Adjust the door so that the bottom of the refrigerator door is

aligned with the top of the freezer drawer. Tighten all screws.

Freezer door models

1. Replace the parts for the bottom hinge as shown. Tighten

screws. Replace the freezer door.

NOTE: Provide additional support for the door while the

hinges are being moved. Do not depend on the door gasket

magnets to hold the door in place while you are working.

2. Assemble the parts for the center hinge as shown in the

Center Hinge graphic, and tighten all the screws. Replace the

refrigerator door.

3. Assemble the parts for the top hinge as shown in the Top

Hinge graphic. Do not tighten the screws completely.

4. Adjust the doors so that the bottom of the refrigerator door is

aligned with the top of the freezer door. Tighten all screws.

Style 2-French Doors

1. Assemble the parts for the top hinges as shown in Top Hinge

graphic. Do not tighten the screws completely.

2. Replace the parts for the bottom hinges as shown in Bottom

Hinge graphic. Tighten screws. Replace the refrigerator

doors.

NOTE: Provide additional support for the refrigerator doors

while the hinges are being moved. Do not depend on the door

gasket magnets to hold the doors in place while you are

working.

3. Align each door so that the bottom of the refrigerator door

aligns evenly with the top of the freezer drawer. Tighten all

screws.

4. Reconnect the wiring plug on top of the left-hand side

refrigerator door.

5. Replace the top hinge covers.

Remove and Replace Freezer Drawer

IMPORTANT:

• Two people may be required to remove and replace the

freezer drawer.

• All graphics are included later inthis section after "Final

Steps."

Remove and Replace Drawer Handle

Metal Handles

• Using a 3_32"Allen wrench, loosen the two set screws located

on the side of each handle. Pull the handle straight out from

the drawer. Make sure you keep the screws for reattaching

the handles. See Metal Handle graphic 2.

• To replace the handle, reverse the directions.

Plastic Handles

• To remove the handle, grasp the handle firmly, slide the

handle to the left and pull the handle straight out from the

drawer. See Plastic Handle graphic 2.

• To replace the handle, position the handle so that the large

holes in the mounting clips are to the right and align the holes

with the door studs. Rotate the handle so that the mounting

clips are flat against the drawer and slide the handle to the

right to engage. See Plastic Handle graphic 2.

Remove Drawer Front

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the

drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in

the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front

Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the freezer compartment. Insert

the screws in the top of the drawer front into the slots in the

drawer brackets. See Drawer Front Replacement graphic.

2. Pull the drawer brackets toward you to insert the two screws

in the bottom of the drawer front into the brackets. See

Drawer Front Replacement graphic.

3. Completely tighten the four screws.

Final Steps

1. Check all holes to make sure that hole plugs and screws are

in place. Reinstall top hinge cover as shown in Top Hinge

graphic.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

2. Plug into a grounded 3 prong outlet.

3. Return all removable door parts to door and food to

refrigerator.

Style 1-Standard Door

Top Hinge

A. Top Hinge Cover

B. _" Hex-Head Hinge Screws

C. Top Hinge

A. Hinge Pin Cover

B. Center Hinge

C. Hinge Screws

Bottom Hinge

A. Hinge Pin Shim (on some models)

B. Bottom Hinge

C. _" Hex-Head Hinge Screws

D. Bottom Hinge Cover

Front Mount

A. Trim Screw

B. Handle Screws

C. Top Trim

D. Bottom Trim

A ....................................._ |

I_'i_" " "_1

A. Door Hinge Hole Plug

Side Mount

1st .............._

3rd .............__))

Front View

A B

A. Door Stop Screws

B. Door Stop

Side View []

__l

-1,,,,

A. Rat-Head Handle

Screws

A. Cabinet Hinge Hole Plugs

Ofo p o oo_\\_I_I............................................A

A. _" Hex-Head Hinge Screws

,,,,

Door Handle \,o

Seal Screw

Front

Some Standard Door

models have plastic

handles. See French

Doors graphic.

o,?A

A. Door Hinge Hole Plugs

Style 2-French Doors

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Top Hinges

t A

......................D

A, H_ge Cover Screw

B, Top Hinge Cover

C, 5/18" Hex-Head Hinge Screws

D, Top Hinge

Bottom Hinges

A. Shim (on some models)

B, Bottom Hinge

C. Hinge Screws

Wiring Plug

Metal Handle

A. 3/32"Set Screw

Metal Handle @

A, 3/32"Set Screw

Plastic Handle

A. Loosen 4 Door Bracket Screws

Depending on your model, your refrigerator may have two front

adjustable rollers (Style 1),or four adjustable rollers (Style 2), or a

leveling screw (Style 3) located at the base of the refrigerator. If

your refrigerator seems unsteady or you want the door to close

more easily, follow the instructions for your model.

Stylel-Two Adjustable Rollers

1. Remove the base grille. Grasp the grille firmly and pull it

toward you.

2. Remove the bracket cover. Insert the eraser end of a pencil in

the cover notch. Apply slight downward pressure to the

notched side of the cover while swinging it off.

Using a screwdriver or 3/8"hex driver, turn the roller

adjustment screw on each side to raise or lower that side of

the refrigerator.

NOTE: It may take several turns of the roller adjustment

screw to adjust the tilt of the refrigerator.

• To raise, turn the roller adjustment screw to the right.

• To lower, turn the roller adjustment screw to the left.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the adjustment screws and

rollers. This makes it easier to turn the screws.

5. Lower the brake foot on each side, by turning it clockwise

until it is firmly against floor.

6. Replace the bracket cover. Place the bracket cover into the

outer edge, swing the cover toward the cabinet and snap it

into place.

7. Replace the base grille.

Style 2-Four Adjustable Rollers

Remove the base grille. Grasp the grille firmly and pull it

toward you.

2. Raise or lower the cabinet. Using a 3/8"hex driver, turn the

roller adjustment screw(s) on each side to raise or lower that

side of the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the adjustment screws and

rollers. This makes it easier to turn the screws. It may take

several turns of the roller adjustment screw to adjust the tilt of

the refrigerator.

• To raise, turn the roller adjustment screw to the right.

• To lower, turn the roller adjustment screw to the left.

3. Turn the brake foot clockwise until it is firmly against the floor

to keep the refrigerator from rolling forward when the freezer

drawer is pulled open.

A. Rear roller adjustment screw

B. Front roller adjustment screw

C. Brake foot

A. Roller adjustment screw

B. Brake foot

Open the door again to make sure that it closes as easily as

you like. If not, tilt the refrigerator slightly more to the rear by

turning both roller adjustment screws to the right. It may take

several more turns, and you should turn both adjustment

screws the same amount.

NOTE: Your refrigerator may have a rear roller adjustment

screw on each side. To raise or lower the rear of the

refrigerator, use a 3/8"hex driver to turn the screws.

4. Open the door again to make sure that it closes as easily as

you like. If not, tilt the refrigerator slightly more to the rear by

turning both leveling screws clockwise. It may take several

more turns, and you should turn both screws the same

amount.

5. Replace the base grille.

Style 3-Leveling screw

1. Remove the base grille. Grasp the grille firmly and pull it

toward you.

Using a 1/4"hex driver, turn the leveling screw on each side to

raise or lower that side of the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws. This

makes it easier to turn the screws. It may take several turns of

the leveling screw to adjust the tilt of the refrigerator.

• To raise, turn the leveling screw clockwise.

• To lower, turn the leveling screw counterclockwise.

A. Rear roller adjustment screw

B. Leveling screw

NOTE: Your refrigerator may have a rear roller adjustment

screw on each side. To raise or lower the rear of the

refrigerator, use a 3/8"hex driver to turn the screws.

Open the door again to make sure that it closes as easily as

you like. If not, tilt the refrigerator slightly more to the rear by

turning both leveling screws clockwise. It may take several

more turns, and you should turn both screws the same

amount.

4. Replace the base grille.

REFRIGERATOR USE

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

A. Hinged seal

Your model may have either Electronic, Dial or Digital Controls.

IMPORTANT:

• Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has

cooled completely, your food may spoil.

NOTE: Adjusting the Refrigerator and Freezer Controls to a

higher (colder) than recommended setting will not cool the

compartments any faster.

• The recommended settings should be correct for normal

household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream

is firm.

• If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

For your convenience, the temperature controls are preset at the

factory. When you first install your refrigerator, make sure the

controls are still set to the recommended setting as shown.

Style 1

Recommended Setting "4"

{umid t# Q rt ol ......................... ............. : ...................

#/ ..... Freeze_¸ _, .............._e{:H_era[o_ ,_

Style 2

Recommended Setting "4"

To Turn Off/On:

Style 1 Press the freezer down arrow touch pad until a

dash (-) appears in both the refrigerator and freezer displays.

Neither compartment will cool.

Style 2 Turn the freezer control to the word OFE Neither

compartment will cool when the freezer is set to OFE

Humidity Control

The humidity control turns on a heater to help reduce moisture on

the door hinge seal. Use in humid environments or when you

notice moisture on the door hinge seal. The refrigerator uses

more energy when Humidity Control is on.

• Press the control to ON when the environment is warm and

more humid, or if you notice moisture on the door hinge seal.

• Press the control to OFF to save energy when the

environment is less humid.

HumidityControl

On Off

Adjusting Controls

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the chart below as

a guide.

For (Style 1) controls press the up or down arrow touch pads, or

for (Style 2) controls turn the dial to adjust the temperature.

Except when starting the refrigerator, do not adjust either control

more than one setting at a time. Wait 24 hours between

adjustments for the temperature to stabilize.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATOR

Control one setting

higher

FREEZER too warm/too little ice FREEZER Control one

setting higher

REFRIGERATOR too cold REFRIGERATOR

Control one setting

lower

FREEZER too cold FREEZER Control one

setting lower

To Turn Your Refrigerator Off/On:

• Press both the freezer and refrigerator (+) touch pads

repeatedly until "OFF" appears in the displays. Allow a few

seconds for the refrigerator to shut off. Neither compartment

will cool.

• Press both the refrigerator and freezer (-) touch pads to turn

on the refrigerator.

Adjusting Digital Controls

The REFRIGERATOR control adjusts the refrigerator

compartment temperature. The FREEZER control adjusts the

freezer compartment temperature.

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the chart as a

guide.

To Adjust Set Point Temperatures:

The first touch of the (+) or (-) touch pad displays the current

temperature set point.

• Press the (+) or (-) touch pads until the desired temperature

set point is displayed.

NOTE: Except when first turning on the refrigerator, do not

adjust either temperature control more than one setting at a

time. Wait 24 hours between adjustments for the temperature

to stabilize.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm Adjust REFRIGERATOR

Control 1° lower

FREEZER too warm/too little ice Adjust FREEZER

Control 1° lower

REFRIGERATOR too cold Adjust REFRIGERATOR

Control 1° higher

FREEZER too cold Adjust FREEZER

Control 1° higher

Additional Digital Control Center Features

Fast Cool

The Fast Cool feature assists with periods of high refrigerator

use, full grocery loads, or temporarily warm room temperatures.

• Press the Fast Cool touch pad to set the freezer and

refrigerator to the lowest temperature settings. Press the Fast

Cool touch pad again to return to the normal refrigerator set

point.

NOTE: The Fast Cool feature will automatically shut off in

approximately 12 hours.

For your convenience, your temperature controls are preset at

the factory. When you first install your refrigerator, make sure the

controls are still set to the Initial settings as shown.

Initial Settings

IMPORTANT: When the power is on, the temperature display

shows the set point temperature of the compartment.

Fast Ice

The Fast Ice feature assists with temporary periods of heavy ice

use by increasing ice production.

• Press the Fast Ice touch pad to set the freezer to the lowest

temperature setting. Press the Fast Ice touch pad again to

return to the normal freezer set point.

NOTE: When Fast Ice is on, the (+) and (-) pads for the freezer

control will not operate. The Fast Ice feature will automatically

shut off in approximately 24 hours.

Temp Alarm

The Temp Alarm feature provides temperature information in the

event of a power outage.

Power outage: During a power outage, if the temperatures in the

refrigerator and freezer compartments exceed normal operating

temperatures, the highest temperature reached will be displayed.

• Press the Temp Alarm touch pad until the indicator light is lit,

to turn on this feature. Press and hold Temp Alarm for

3 seconds until the indicator light goes off to turn off this

feature.

Temperature alarm: An alarm will sound repeatedly if the freezer

or refrigerator compartment temperatures exceed normal

operating temperatures for an hour or more.

The temperature displays will alternately show the current

temperatures and the highest temperatures the compartments

reached.

• Press the Temp Alarm touch pad once to stop the audible

alarm and alternating temperature displays. The Temp Alarm

light will continue to flash until the refrigerator returns to the

set temperature.

Door Alarm

The Door Alarm feature sounds a chime every few seconds when

the refrigerator door has been left open for 5 continuous minutes.

The chime will sound until the door is closed or Door Alarm is

turned off.

• Press the Door Alarm touch pad to turn this feature on or off.

The indicator light will be lit when the Door Alarm feature is

on.

Reset Filter

The Reset Filter control allows you to restart the water filter status

tracking feature each time you replace your water filter. See

"Water Filtration System."

Press and hold the Reset Filter touch pad for 3 seconds, until

the Order or Replace light turns off.

Order Replace

Press and hold 3 sec to

reset water filter li_,ht

Digital Control User Preferences

The control center allows you to set user preferences, if desired.

Super Cool (CC)

This preference allows you to improve the air flow and

temperature control. To save energy, turn off this feature by

pressing OFR

Temperature Display (F_C}

This preference allows you to change the temperature display.

F - Temperature in degrees Fahrenheit

C - Temperature in degrees Celsius

Alarm (AL)

This preference allows you to turn off the sound of all alarms.

ON - You will hear the alarm sound.

OFF - You will not hear the alarm sound.

Auto Light Level Selection (LL)

This preference allows you to adjust the dispenser light level from

dimmest to brightest (settings 1through 9).

NOTE: The Auto Light feature on the control center must be

selected to activate this preference.

Sabbath Mode (SAB)

ON - All control panel lights, interior lights and alarm tones will be

disabled.

OFF - All control panel lights, interior lights and alarm tones will

be enabled.

NOTE: Press the Door Alarm touch pad for 3 seconds to restore

all lights.

To Access the User Preferences Menu:

1. Press and hold the Door Alarm touch pad for 3 seconds. The

preference name will appear in the Freezer display and the

preference status (F or C) or (ON or OFF) will appear in the

Refrigerator display.

2. Use the Freezer (+) or (-) touch pads to scroll through the

preference names. When the desired preference name is

displayed, press the Refrigerator (+) or (-) touch pads to

change the preference status.

3. Set your preferences by pressing and holding the Door Alarm

touch pad for 3 seconds, or by shutting the refrigerator

compartment door.

You can control the amount of humidity in the moisture-sealed

crisper. Depending on your model, adjust the control to any

setting between FRUIT and VEGETABLES or LOW and HIGH.

FRUIT / LOW (open) for best storage of fruits and vegetables

with skins.

VEGETABLES / HIGH (closed) for best storage of fresh, leafy

vegetables.

()ll £()IY%{i! I II( I=(: _I

Turning the Ice Maker On/Off

To turn the ice maker ON, simply lower the wire shutoff arm.

Tomanually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click.

NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

Ice Production Rate

• The ice maker should produce a complete batch of ice

approximately every 3 hours.

• To increase ice production, lower the freezer and refrigerator

temperature. See "Using the Controls." Wait 24 hours

between adjustments.

Remember

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

• The quality of your ice will be only as good as the quality of

the water supplied to your ice maker. Avoid connecting the

ice maker to a softened water supply. Water softener

chemicals (such as salt) can damage parts of the ice maker

and lead to poor quality ice. If a softened water supply cannot

be avoided, make sure the water softener is operating

properly and is well maintained.

• Do not store anything on top of the ice maker or in the ice

storage bin.

IMPORTANT:

{)} H)'_O 'H)( _!>'l;i,}

After connecting the refrigerator to a water source, flush the

water system. Press the button on the dispenser for

5 seconds, then release it for 5 seconds. Repeat until water

begins to flow. Once water begins to flow, continue

depressing and releasing the dispenser button (5 seconds on,

5 seconds off) for an additional 2 minutes. This will flush air

from the filter and water dispensing system. Additional

flushing may be required in some households. As air is

cleared from the system, water may spurt out of the

dispenser.

NOTE: After 5 minutes of continuous dispensing, the

dispenser will stop dispensing water to avoid flooding. To

continue dispensing, press the dispenser button again.

Allow 24 hours for the refrigerator to cool down and chill

water. Dispense enough water every week to maintain a fresh

supply.

Dispensing Water

1. Hold a container under the dispenser while pressing the

button.

2. Release the button to stop dispensing.

The water filter is located in the upper right-hand corner of the

refrigerator compartment.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Water Filter Status Lights

The water filter indicator lights will remind you when it is time to

order and replace your water filter. When the yellow (Order) light

is on, it is almost time to change the water filter. When the red

(Replace) light is on, a new water filter should be installed. It is

recommended that you replace the water filter when the indicator

light changes to red OR earlier if the flow of water to your water

dispenser or ice maker decreases noticeably.

After replacing the water filter, press and hold Reset Filter for

three seconds. The Order and Replace indicator lights will blink

and then go off when the system is reset. See "Using the

Controls."

Replacing the Water Filter

To purchase a replacement water filter, model UFK8001AXX-750,

contact your dealer or call 1-877-232-6771 U.S.A. or

1-800-807-6777 Canada.

IMPORTANT: Air trapped in the water system may cause water

and filter to eject. Always dispense water for at least 2 minutes

before removing the filter or blue bypass cap.

1. Turn filter counterclockwise to remove.

2. Remove sealing label from replacement filter and insert the

filter end into the filter head.

3. Turn the filter clockwise until it stops. Snap the filter cover

closed.

NOTE: The dispenser feature may be used without a water filter

installed. Your water will not be filtered. If this option is chosen,

replace the filter with the blue bypass cap.

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water.

• To keep your stainless steel refrigerator looking like new

and to remove minor scuffs or marks, it is suggested that

you use the manufacturer's approved Stainless Steel

Cleaner and Polish, Part Number 20000008. To order the

cleaner, call 1-877-232-6771 U.S.A. or 1-800-807-6777

Canada.

IMPORTANT: This cleaner is for stainless steel parts only!

Do not allow the Stainless Steel Cleaner and Polish to come

into contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If unintentional contact

does occur, clean plastic part with a sponge and mild

detergent in warm water. Dry thoroughly with a soft cloth.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with an appliance bulb of the same size, shape,

and wattage (no greater than 40 watts).

1. Unplug the refrigerator or disconnect power.

2. Remove the light shield, if necessary.

Freezer drawer models

Top of the refrigerator compartment - Slide the light shield

toward the back of the compartment to release it from the

light assembly.

Top of freezer compartment - The light shield opens from

the back. Firmly press forward on the notches in the back

of the shield and pull the shield down.

NOTE: You may need to remove the upper freezer shelf or

basket to access the light assembly.

Freezer door models

Top of the refrigerator compartment - Slide the shield

toward the back to release it from the light assembly.

Top of freezer compartment - Squeeze and pull rear of

light shield toward you to release the tabs, then pull

down.

3. Replace the burned-out bulb(s) with an appliance bulb(s) no

greater than 40 watts.

4. Replace the light shield.

Freezer drawer models

Top of the refrigerator compartment - Insert the tabs on

the shield into the liner holes on each side of light

assembly. Slide the shield toward the front until it locks

into place.

NOTE: To avoid damaging the light shield, do not force

the shield beyond the locking point.

Top of the freezer compartment - Insert the front tabs of

the shield into the liner and snap the back portion of the

shield over the light assembly.

Freezer door models

Top of the refrigerator compartment - Insert the tabs on

the shield into the liner holes on each side of the light

assembly. Slide the shield toward the front until it locks.

NOTE: To avoid damaging the light shield, do not force

the shield beyond the locking point.

Top of freezer compartment - Insert front tabs of light

shield into liner and snap the back of the shield over light

assembly.

5. Plug in refrigerator or reconnect power.

TROUBLESHOOTING

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call.

In the U.S.A., www.maytag.com In Canada, www.maytag.ca

O}se_x_£Ii,{>s

(

The refrigerator will not operate The motor seems to run too much

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Power cord unplugged?Plug intoa grounded 3 prong

outlet.

Is outlet working? Plug in a lamp to see if the outlet is

working.

Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. If the problem continues,

call an electrician.

Are controls on? Make sure the refrigerator controls are on.

See "Using the Controls."

New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

Your new refrigerator may run longer than your old one due to its

high-efficiency compressor and fans. The unit may run even

longer if the room is warm, a large food load is added, doors are

opened often, or if the doors have been left open.

The refrigerator seems noisy

Refrigerator noise has been reduced over the years. Due to this

reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below

are listed some normal sounds with explanations.

Buzzing - heard when the water valve opens to fill the ice

maker

• Pulsating - fans/compressor adjusting to optimize

performance

• Hissing/Rattling - flow of refrigerant, movement of water

lines, or from items placed on top of the refrigerator

• Sizzling/Gurgling - water dripping on the heater during

defrost cycle

• Popping - contraction/expansion of inside walls, especially

during initial cool-down

• Water running - may be heard when water melts during the

defrost cycle and runs into the drain pan

• Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct

position.

The doors are difficult to open

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

• Gaskets dirty or sticky? Clean gaskets and contact surfaces

with mild soap and warm water. Rinse and dry with soft cloth.

Temperature is too warm

• New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

• Door(s) opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

• Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

• Controls set correctly for the surrounding conditions?

Adjust the controls a setting colder. Check temperature in

24 hours. See "Using the Controls."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s) opened often or left open? Allows humid air to

enter refrigerator. Minimize door openings and keep doors

fully closed.

_'_d¸* _' S _ •

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

• Ice maker turned on? Make sure wire shutoff arm or switch

(depending on model) is in the ON position.

• New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

• Freezer door closed completely? Firmly close the freezer

compartment door. If the freezer compartment door will not

close all the way, see "The doors will not close completely."

• Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil.

• Water filter installed on the refrigerator? Remove filter and

operate ice maker. If ice volume improves, then the filter may

be clogged or incorrectly installed. Replace filter or reinstall it

correctly.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

• Water filter installed on the refrigerator? Remove filter and

operate ice maker. If ice quality improves, then the filter may

be clogged or incorrectly installed. Replace filter or reinstall it

correctly.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

• Questions remain regarding water pressure? Call a

licensed, qualified plumber.

Off-taste, odor or gray color in the ice

• New plumbing connections? New plumbing connections

can cause discolored or off-flavored ice.

• Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice.

• Odor transfer from food? Use airtight, moisture proof

packaging to store food.

• Are there minerals (such as sulfur) in the water? A water

filter may need to be installed to remove the minerals.

• Water filter installed on the refrigerator? Gray or dark

discoloration in ice indicates that the water filtration system

needs additional flushing. Flush the water system before

using a new water filter. Replace water filter when indicated.

See "Water Filtration System."

The water dispenser will not operate properly

Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

Kink in the water source line? Straighten the water source

line.

New installation? Flush and fill the water system. See "Water

Dispenser."

Is the water pressure at least 35 psi (241 kPa)? The water

pressure to the home determines the flow from the dispenser.

See "Water Supply Requirements."

• Water filter installed on the refrigerator? Remove filter and

operate dispenser. If water flow increases, the filter may be

clogged or incorrectly installed. Replace filter or reinstall it

correctly.

• Refrigerator door closed completely? Close the door

firmly. If it does not close completely, see "The doors will not

close completely."

• Recently removed the doors? Make sure the water

dispenser wire/tube assembly has been properly

reconnected. See "Refrigerator Doors."

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

Water is leaking from the dispenser system

NOTE: One or two drops of water after dispensing is normal.

• Glass not being held under the dispenser long enough?

Hold the glass under the dispenser 2 to 3 seconds after

releasing the dispenser lever.

• New installation? Flush the water system. See "Water

Dispenser."

• Recently changed water filter? Flush the water system. See

"Water Dispenser."

• Water on the floor near the base grille? Make sure the

water dispenser tube connections are fully tightened. See

"Refrigerator Doors."

Water from the dispenser is warm

NOTE: Water from the dispenser is only chilled to 50°F (10°C).

• New installation? Allow 24 hours after installation for the

water supply to cool completely.

• Recently dispensed large amount of water? Allow

24 hours for water supply to cool completely.

• Water not been recently dispensed? The first glass of water

may not be cool. Discard the first glass of water.

• Refrigerator connected to a cold water pipe? Make sure

the refrigerator is connected to a cold water pipe. See "Water

Supply Requirements."

WATER FILTER

CERTIFICATIONS

Trademark!Model Desianat_on

UKF80{H AXX750

_690116-750

67003523-750

Manufacturer: PentaPhre 'lnc

State of California

Department of Health Services

Water Treatment Device

Certificate Number

03- 1583

Date lssuee Set_tember/6.2OO3

DamReviq_d April 29 9(1t)4

Reolaeement Elements

The water treatment de_ice s) listed on this certificate have,met the testing reqt_ reme6ts pursuant to Section

116830 of the Health and Safety Code for the following he_.lth related e6ntarainahts_

Microbiol_,_ical Cdntaminaots and YurbiditiJ

Cysts

r['urb_d'tlY i

OrcJanic OontaNinants

Rated Service Capacity: 750 gal Rated Service Flow: 878 gpm

Conditions of Cerhfication:

Do not axe where water is microbiologk'ally urtsatb or with water of m_known quahw, cxcep_ thai _y_terns certified for

cyst reduLfion may be used on di_inlected water_ that may contain lllterable Lyqs

PRODUCT DATA SHEETS

Interior Water Filtration System

Model UFK8001AXX-750 Capacity 750 Gallons (2839 Liters)

System tested and certified by NSF International against NSF/ANSI

Standard 42 for the reduction of Chlorine Taste and Odor, Particulate

Class I*; and against NSF/ANSI Standard 53 for the reduction of Lead,

Mercury, Atrazine, Benzene, p-Dichlorobenzene, Carbofuran,

Toxaphene, Cysts, Turbidity, Asbestos and Lindane.

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.

Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum% Average%

Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction

Chlorine Taste/Odor 50% reduction 1.88 mg/L 2.0 mg/L _+10% 0.06 mg/L 0.05 mg/L 96.84 >97.26

Particulate Class I* 85% reduction 5,700,000 #/mL Atparticles/mleast10,000L 69,000 #/mL** 30,583 #/mL 98.94 99.52

Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum%

Reduction Requirements Influent Concentration Effluent Effluent Reduction

Lead: @pH 6.5 0.010 mg/L 0.153 mg/U 0.15 mg/L + 10% < 0.001 mg/L < 0.001mg/L >99.29%

Lead: @pH 8.5 0.010 mg/L 0.150 mg/U 0.15 mg/L _+10% < 0.001 mg/L < 0.001mg/L >99.29%

Mercury: @ pH 6.5 0.002 mg/L 0.006 mg/L 0.006 mg/L + 10% 0.0005 mg/L 0.0003 mg/L 90.91

Mercury: @ pH 8.5 0.002 mg/L 0.006 mg/L 0.006 mg/L _+10% 0.0015 mg/L 0.0008 mg/L 75.93

Benzene 0.005 mg/L 0.014 mg/L 0.015 mg/L _+10% 0.0011 mg/L 0.0006 mg/L 92.14%

p-Dichlorobenzene 0.075 mg/L 0.208 mg/L 0.225 mg/L _+10% < 0.0005 mg/L < 0.0005 mg/[ 99.74%

Carbofuran 0.04 mg/L 0.081 mg/L 0.08 mg/L _+10% < 0.001mg/L < 0.001mg/L 98.46%

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 _+10% < 0.001 mg/L < 0.001mg/L 91.67%

Atrazine 0.003 mg/L 0.009mg/L 0.009 mg/L _+10% < 0.002 mg/L < 0.002 mg/L 75.31%

Asbestos 99% 155 MF/L 107to 108fibers/L tt < 1 MF/L < 1 MF/L >99.99%

Live Cysts _ >99.95% 166,500 #/L 50,000/L min. < 1 #/U < 1 #/U >99.99

Turbidity 0.5 NTU 10.7 NTU 11 _+1 NTU 0.49 NTU 0.31 NTU 95.2

Lindane 0.0002 mg/L 0.002 mg/L 0.002 _+10% < 0.0001mg/L 0.000 mg/L 96.50%

Test Parameters: pH = 7.5 _+0.5 unless otherwise noted.

71.6°F (20°C to 22°C).

• It is essential that operational, maintenance, and filter

replacement requirements be carried out for the product to

perform as advertised.

• The filter monitor system measures the amount of water that

passes through the filter and alerts you to replace the filter.

When 90% of the filter's rated life is used, the yellow (Order)

light comes on. When 100% of the filter's rated life is used,

the red (Replace) light comes on, and it is recommended that

you replace the filter. For models without filter status lights,

replace the filter every 6 months. Use replacement filter

model UFK8001AXX-750. 2007 suggested retail price of

$49.99 U.S.A./S65.95 Canada. Prices are subject to change

without notice.

Flow = 0.78 gpm (1.9 Lpm). Pressure = 60 psig (41

Average%

Reduction

>99.35%

>99.33%

95.70

86.22

95.71%

99.76%

98.74%

92.97%

76.99%

>99.99%

>99.99

97.09

98.72%

3.7 kPa). Temp. = 68°F to

• Refer to the "Water Filtration System" section for the

Manufacturer's name and telephone number.

• Refer to the "Warranty" section for the Manufacturer's limited

warranty.

The product is for cold water use only.

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

Application Guidelines/Water Supply Parameters

Water Supply City or Well

Water Pressure 35 - 120 psi (241 - 827 kPa)

Water Temperature 33° - 100°F (1° _ 38oC)

Service Flow Rate 0.78 gpm (2.9 L/min.) @ 60 psi

*Class I particle size: >0.5 to <1 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

tThese contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.

ttFibers greater than 10 um in length

_Based on the use of Cryptosporidium parvum oocysts

® NSF is a registered trademark of NSF International.

La page charge ...

Maytag MFD2562VEA10 Le manuel du propriétaire

Marque: Maytag

Modèle: MFD2562VEA10

Catégorie: Frigos

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MFD2562VEA10 Owner's manual

Maytag MFD2562VEA10 Le manuel du propriétaire

Maytag MFD2562VEA10 Le manuel du propriétaire

dans d''autres langues

Documents connexes