Refrigerators
Bottom-Freezer
162D9629P005 49-60135-1 WR6S1 08-02 JR
Model 18
GEAppliances.com
Safety Instructions . . . . . . . .2–4
Operating Instructions
Additional Features . . . . . . . . . .8
Automatic Icemaker . . . . . .9, 10
Care and Cleaning . . . . . . .11, 12
Crispers and Pans . . . . . . . . . . .7
Getting Started . . . . . . . . . . . . .5
Replacing the Light Bulbs . . . .12
Shelves, Bins and
Water Dispenser . . . . . . . . . . . .6
Installation Instructions
Preparing to Install
the Refrigerator . . . . . . . . . . . .13
Reversing the Door Swing . . 14–17
Troubleshooting Tips . . . 18–20
Normal Operating Sounds . . .18
Consumer Support
Consumer Support . . . . . . . . . 24
Warranty (Canadian) . . . . . . . 22
Warranty (U.S.) . . . . . . . . . . . .23
Write the model and serial numbers here:
Model # ________________________
Serial # ________________________
Find these numbers on a label on the
left side, near the top of the freezer
compartment.
Owner’s Manual and
Installation Instructions
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
2
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner’s Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
■
■ This refrigerator must be properly installed
and located in accordance with the Installation
Instructions before it is used.
■
■ Do not allow children to climb, stand or hang
on the shelves in the refrigerator. They could
damage the refrigerator and seriously injure
themselves.
■
■ Do not touch the cold surfaces in the freezer
compartment when hands are damp or wet.
Skin may stick to these extremely cold surfaces.
■
■ Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
■
■ Do not refreeze frozen foods which have
thawed completely.
■
■ In refrigerators with automatic icemakers, avoid
contact with the moving parts of the ejector
mechanism, or with the heating element located
on the bottom of the icemaker. Do not place
fingers or hands on the automatic icemaking
mechanism while the refrigerator is plugged in.
■
■ Keep fingers out of the “pinch point” areas;
clearances between the doors and between
the doors and cabinet are necessarily small.
Be careful closing doors when children are
in the area.
■
■ Unplug the refrigerator before cleaning and
making repairs.
NOTE: We strongly recommend that any servicing be
performed by a qualified individual.
■
■ Before replacing a burned-out light bulb,
unplug the refrigerator or turn off power at the
circuit breaker or fuse box in order to avoid
contact with a live wire filament. (A burned-out
light bulb may break when being replaced.)
■
■ Turning the control to the OFF position does
not remove power to the light circuit.
3
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
PROPER DISPOSAL OF THE REFRIGERATOR
Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are
still dangerous…even if they will sit for “just a few
days.” If you are getting rid of your old refrigerator,
please follow the instructions below to help prevent
accidents.
Before You Throw Away Your Old Refrigerator
or Freezer:
■ Take off the doors.
■ Leave the shelves in place so that children
may not easily climb inside.
CFC Disposal
Your old refrigerator has a cooling system that used
CFCs (chlorofluorocarbons). CFCs are believed to
harm stratospheric ozone.
If you are throwing away your old refrigerator, make
sure the CFC refrigerant is removed for proper
disposal by a qualified servicer. If you intentionally
release this CFC refrigerant you can be subject to
fines and imprisonment under provisions of
environmental legislation.
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend
against the use of an extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United
States) or a CSA certified (in Canada), 3-wire grounding type appliance extension cord having a grounding
type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.
DANGER! RISK OF CHILD ENTRAPMENT
GEAppliances.com
4
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked by
a qualified electrician to make sure the outlet
is properly grounded.
Where a standard 2-prong wall outlet is
encountered, it is your personal responsibility
and obligation to have it replaced with a properly
grounded 3-prong wall outlet.
The refrigerator should always be plugged into
its own individual electrical outlet which has
a voltage rating that matches the rating plate.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your refrigerator by pulling on
the power cord. Always grip plug firmly and pull
straight out from the outlet.
Repair or replace immediately all power cords
that have become frayed or otherwise damaged.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
When moving the refrigerator away from the
wall, be careful not to roll over or damage the
power cord.
USE OF ADAPTER PLUGS (Adapter plugs not permitted in Canada)
Because of potential safety hazards under certain conditions, we strongly recommend against
the use of an adapter plug.
However, if you must use an adapter, where local
codes permit, a temporary connection may be made
to a properly grounded 2-prong wall outlet by use
of a UL-listed adapter available at most local
hardware stores.
The larger slot in the adapter must be aligned with
the larger slot in the wall outlet to provide proper
polarity in the connection of the power cord.
When disconnecting the power cord from the
adapter, always hold the adapter in place with one
hand while pulling the power cord plug with the
other hand. If this is not done, the adapter ground
terminal is very likely to break with repeated use.
If the adapter ground terminal breaks, DO NOT USE
the refrigerator until a proper ground has been
established.
Attaching the adapter ground terminal to a wall outlet
cover screw does not ground the appliance unless the
cover screw is metal and not insulated, and the wall
outlet is grounded through the house wiring. You should
have the circuit checked by a qualified electrician to make
sure the outlet is properly grounded.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
Consumer SupportTroubleshooting TipsOperating Instructions
Safety Instructions
Installation Instructions
5
Getting started. GEAppliances.com
Checklist
Freezer Control
The freezer control maintains the temperature in the freezer compartment.
Refrigerator Control
The refrigerator control maintains the temperature throughout the refrigerator compartment.
Moving the refrigerator control to OFF stops cooling in both areas---refrigerator and freezer---but
does not shut off power to the refrigerator.
After changing the controls, allow 24 hours for the refrigerator to reach the temperature you have set.
Install Top Hinge Cover
If not already installed, locate the plastic hinge
cover inside the parts kit and carefully snap it over
the top hinge.
Adjust Rollers So Doors/Drawer Automatically Close
The refrigerator should be elevated slightly at the front so
the doors/drawer will close automatically when partially
open. See Preparing to Install the Refrigerator.
Initially set the refrigerator and freezer controls at 5.
For refrigerator and freezer, 5 is normal, 9 is coldest.
If you want colder or warmer temperatures, adjust the
refrigerator temperature first. When satisfied with that
setting, adjust the freezer temperature.
COLD 1
9 COLDEST
NORMAL
Top Hinge Cover Part Nos.
WR2S56 Bisque
WR2S72 Black
WR2S8 White
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
About the refrigerator shelves, bins and water dispenser.
Not all features are on all models.
Rearranging the Shelves
Glass and wire shelves in the refrigerator compartment are adjustable.
To Remove To Replace
Lift up and out
2
Insert
top hook
1
Lower to
lock in place
2
Tilt up
1
Adjustable Door Bins
Adjustable bins can easily be carried from
refrigerator to work area.
To remove: Tilt the bin up and pull out
on the molded supports until it comes
completely out of the door.
To replace or relocate: Select desired height,
engage the bin in the molded supports of
the door and slide the bin in. The bin will
hook in place.
The snuggers help prevent tipping, spilling
or sliding of small items stored on the door
shelf. Place a finger on either side of the
divider near the front and move it back
and forth to fit your needs.
Brita
®
Water Dispenser
To install: Grasp the dispenser as shown.
Using a slight backward tilt, align the
mounting brackets on the dispenser with
the support brackets in the refrigerator door.
Gently slide the dispenser back until it
touches the door and lower it into the
support brackets.
To remove: Tilt the dispenser up at the front
and pull it forward on the molded support
brackets until it comes completely out of
the door.
Slide-Out Spillproof Shelf
The slide-out spillproof shelf allows you
to reach items stored behind others. The
special edges are designed to help prevent
spills from dripping to lower shelves.
Make sure you push the shelves all the way back
in before you close the door.
6
Snugger
7
Consumer SupportTroubleshooting TipsOperating Instructions
Safety Instructions
Installation Instructions
About the crispers and pans.
GEAppliances.com
Adjustable Humidity Crispers
Slide the control all the way to the
HIGH setting to provide high humidity
recommended for most vegetables.
Slide the control all the way to the
LOW setting to provide lower humidity
levels recommended for most fruits.
Detachable Snack Pan
The slide-out snack pan can be
removed and taken to the sink or
food preparation area.
The pan and the adjustable shelf
to which it attaches can be relocated
at any level.
Crisper and Cover Removal
To Remove Crispers:
These drawers can be removed easily by lifting up slightly
while pulling the drawers past the stop location.
When the door cannot be opened enough to pull the drawer
straight out, slide the drawer toward the middle and remove it.
To Remove Cover:
Remove the glass, then the frame. When replacing the glass,
push the rear edge firmly into the frame.
Fruit and Vegetable Crispers
8
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
Some additional features.
Not all features are on all models.
Beverage Rack (on some models)
This slide-out rack provides storage for
a variety of beverages.
The rack and the adjustable shelf to which
it attaches can be relocated to any level.
Removable Wine Rack (on some models)
This rack is designed to hold a bottle on
its side.
Freezer Shelves and Baskets
On swing door models with three sliding
baskets: Both the lower and upper baskets
slide out to provide easy access to foods
stored in the freezer. When the lower
basket is pulled out, the upper basket may
be pushed back to further improve access
to the lower basket.
On swing door models with one sliding
basket and two split fixed shelves:
The lower basket slides out to provide
easy access to foods stored in this basket.
The top full width fixed shelf provides a
convenient location to store ice cube trays
and ice bucket as well as a variety of foods.
On drawer models: The lower basket slides
out when the drawer is opened to provide
easy access to foods stored in this basket.
The upper basket may be pushed back to
further improve access to the lower basket.
The baskets may be easily removed for
cleaning spills or crumbs off the freezer
floor, or for installing an icemaker.
Consumer SupportTroubleshooting TipsOperating Instructions
Safety Instructions
Installation Instructions
About the automatic icemaker. GEAppliances.com
Icemaker Accessory Kit
If your refrigerator did not come already
equipped with an automatic icemaker,
an icemaker accessory kit (IM-4 for U.S.
models, or IM4-1 for Canadian models) is
available at extra cost.
Automatic Icemaker (on some models)
The icemaker will produce seven cubes
per cycle---approximately 100–130 cubes
in a 24-hour period, depending on
freezer compartment temperature,
room temperature, number of door
openings and other use conditions.
If the refrigerator is operated before the
water connection is made to the icemaker,
set the power switch to O (off).
When the refrigerator has been connected
to the water supply, set the power switch to
I (on). Do not open the door/drawer for
approximately 4 hours. This will allow the
freezer to reach the correct operating
temperature for making ice, and will
prevent water from spilling out of the
icemaker mold.
Special Note about the Green Power Light:
Even when the icemaker power switch is in
the I (on) position, power to the icemaker
will be interrupted when the freezer
door/drawer is open. This prevents ice
ejecting from the icemaker from missing
the ice bucket and dropping into the back
of the freezer. Because power to the
icemaker is interrupted while the
door/drawer is open, the green power light
on the icemaker will be off. To make sure
the icemaker is working properly, press the
freezer light switch located on the upper
right side of the freezer compartment. The
power light on the icemaker will come on.
The icemaker will fill with water when it
cools to 15°F (–10°C). A newly-installed
refrigerator may take 12 to 24 hours to
begin making ice cubes.
Throw away the first few batches of ice to
allow the water line to clear.
Be sure nothing interferes with the sweep
of the feeler arm.
When the bin fills to the level of the feeler
arm, the icemaker will stop producing ice.
It is normal for several cubes to be joined
together.
If ice is not used frequently, old ice cubes
will become cloudy, taste stale and shrink.
If ice cubes get stuck in the icemaker, set
the power switch to O (off) and remove the
cubes. Set the power switch to I (on) to
restart the icemaker.
After the icemaker has been turned on
again, there will be a delay of about
45 minutes before the icemaker resumes
operations.
NOTE: In homes with lower-than-average water
pressure, you may hear the icemaker cycle multiple
times when making one batch of ice.
A newly-installed refrigerator may take 12–24 hours to begin making ice.
Icemaker
Feeler Arm
Power Switch
Icemaker Installation
A special icemaker mounting block must
be used when installing an icemaker.
Directions on how to install the icemaker
mounting block are included in the
Icemaker Accessory Kit Installation
Instructions.
For U.S. models, the mounting block
is included with the refrigerator. For
Canadian models, the mounting block
is included in the optional icemaker
accessory kit (IM4-1).
Mounting Block
Part No. WR2M3604
Screws
Part No. WR1M478
9
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
10
About the automatic icemaker.
A newly-installed refrigerator may take 12–24 hours to begin making ice.
Ice Cube Tray Shelf (on some models)
Some models have a small separate shelf
for ice cube trays.
Ice Trays and Bucket (on some models)
To remove ice cubes from the tray, place
the tray upside down on the bucket as
shown. Press down on the tray and the
cubes will pop out.
Large Ice Bucket (on some models)
This bucket is required when using an
automatic icemaker. When installing an
icemaker, the upper left basket must be
removed in order to make room for the
large ice bucket. If an icemaker is not
installed, the bucket can be removed
to provide more capacity in the freezer
compartment. For U.S. models, the bucket
is included with the refrigerator. For
Canadian models, the bucket is included
in the optional icemaker accessory
kit (IM4-1).
Part No.
WR30S1
11
Care and cleaning of the refrigerator.
GEAppliances.com
Cleaning the Outside
Keep the outside clean. Wipe with a clean
cloth lightly dampened with mild liquid
dish detergent. Dry and polish with a clean,
soft cloth.
Do not wipe the refrigerator with a soiled dish
cloth or wet towel. These may leave a residue
that can erode the paint. Do not use scouring
pads, powdered cleaners, bleach or cleaners
containing bleach because these products can
scratch and weaken the paint finish.
The stainless steel panels and door handles
(on some models) can be cleaned with
a commercially available stainless steel
cleaner such as Stainless Steel Magic.
™
Stainless Steel Magic is available at Ace,
True Value, Servistar, HWI and other
leading stores. It is also available through
GE Parts and Accessories, 800.626.2002, or
visit our Website, GEAppliances.com. In
Canada, call 1.888.261.3055 or visit our
Website, geappliances.ca. Order part
number WX10X15.
Do not use appliance wax or polish on the
stainless steel.
Cleaning the Inside
To help prevent odors, leave an open box of
baking soda in the fresh food and freezer
compartments.
Unplug the refrigerator before cleaning. If this
is not practical, wring excess moisture out
of sponge or cloth when cleaning around
switches, lights or controls.
Use warm water and baking soda solution---
about a tablespoon (15 ml) of baking soda
to a quart (1 l) of water. This both cleans
and neutralizes odors. Rinse and wipe dry.
After cleaning the door gaskets, apply a
thin layer of paraffin wax to the door
gaskets at the hinge side. This helps keep
the gaskets from sticking and bending out
of shape.
Avoid cleaning cold glass shelves (on
some models) with hot water because
the extreme temperature difference
may cause them to break. Handle glass
shelves carefully. Bumping tempered
glass can cause it to shatter.
The Brita
®
Water Dispenser (on some models)
is dishwasher safe.
Do not wash any other plastic refrigerator parts
in the dishwasher.
Consumer SupportTroubleshooting TipsOperating Instructions
Safety Instructions
Installation Instructions
12
Care and cleaning of the refrigerator.
Preparing for Vacation
For long vacations or absences, remove
food and unplug the refrigerator. Move
the control to the OFF position, and clean
the interior with a baking soda solution
of one tablespoon (15 ml) of baking soda
to one quart (1 l) of water. Leave the
doors open.
If an icemaker is installed, move the
icemaker feeler arm to the STOP (up)
position and shut off the water supply
to the refrigerator.
Preparing to Move
Secure all loose items such as grille,
shelves and drawers by taping them
securely in place to prevent damage.
Be sure the refrigerator stays in an upright
position during moving.
Replacing the Light Bulbs
To replace a burned-out bulb, unplug the
refrigerator from its electrical outlet.
In the refrigerator compartment, remove
the lens cover by gently applying pressure
to the back corners of the lens cover and
pulling the cover free from the control
housing. Unscrew the bulb when cool
and replace it with an appliance bulb
of the same or lower wattage.
There is also a light in the refrigerator
control panel. To replace it, simply
unscrew the bulb when cool and
replace it with an appliance bulb of
the same or lower wattage.
In the freezer compartment, simply unscrew
and replace the bulb after ensuring the
refrigerator is unplugged.
Turning the control to the OFF position does not
remove power to the light circuit.
Behind the Refrigerator
Be careful when moving the refrigerator
away from the wall. All types of floor
coverings can be damaged, particularly
cushioned coverings and those with
embossed surfaces.
Pull the refrigerator straight out and return
it to position by pushing it straight in.
Moving the refrigerator in a side direction
may result in damage to the floor covering
or refrigerator.
When pushing the refrigerator back,
make sure you don’t roll over the
power cord.
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
13
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT – Save these
instructions for local inspector’s use.
•
IMPORTANT – Observe all
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions
for future reference.
• Skill level – Installation of this appliance requires
basic mechanical skills.
• Completion time – Refrigerator Installation
15 minutes
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is not
covered under the Warranty.
• Do not install the refrigerator where the temperature
will go below 60°F (16°C) because it will not run often
enough to maintain proper temperatures.
• Do not install the refrigerator where the temperature
will go above 100°F (37°C) because it will not perform
properly.
• Install the refrigerator on a floor strong enough to
support it when fully loaded.
REFRIGERATOR LOCATION
Installation
Refrigerator
Instructions
Model 18
Allow the following clearances for ease of installation,
proper air circulation and plumbing and electrical
connections:
• Sides 1/8″ (3 mm)
• Top 1″ (25 mm)
• Back 1″ (25 mm)
If the refrigerator is against a wall on either side, allow
a minimum of 1
3
⁄4″ (45 mm) between the wall and the
side of the refrigerator to allow for door and handle
clearance.
CLEARANCES
If the refrigerator has an icemaker, it will have to be
connected to a cold water line. A GE water supply kit
(containing tubing, shutoff valve, fittings and
instructions) is available at extra cost from your dealer,
by visiting our Website at GEAppliances.com (in
Canada at geappliances.ca) or from Parts and
Accessories, 800.626.2002 (in Canada 1.888.261.3055).
WATER SUPPLY TO THE ICEMAKER
(ON SOME MODELS)
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com
In Canada, call 1.800.361.3400
or Visit our Website at: geappliances.ca
Remove all packaging tape and peel-off films. These
tapes were added to secure and protect your refrigerator
during shipping.
PACKAGING TAPE
The rollers have 2 purposes:
■ The rollers are used to level the refrigerator.
NOTE: It is recommended that the refrigerator be
elevated 1/2″ (13 mm) in the front. When installing an
icemaker, make sure that the icemaker is completely
level while maintaining the refrigerator incline.
■ Rollers allow you to move the refrigerator away from
the wall for cleaning.
To adjust the rollers:
Remove the base grille by pulling it straight out.
Turn the two front roller
adjusting screws clockwise
to raise the refrigerator,
counterclockwise to lower it.
Use a 3/8″ socket wrench,
adjustable wrench or pliers.
NOTE: The refrigerator must be supported by all four
rollers. To test, move the refrigerator to make sure it
does not rock.
ROLLERS
Front Roller Adjusting Screw
REVERSING THE DOOR SWING
When reversing the door swing:
• Read the instructions all the way through before
starting.
• NOTE: Doors on stainless steel models are not
reversible.
• Handle parts carefully to avoid scratching paint.
• Set screws down by their related parts to avoid using
them in the wrong places.
• Provide a non-scratching work surface for the doors.
These instructions are for changing the hinges from
the right side to the left side---if you ever want to
change the hinges back to the right side, follow these
same instructions and reverse all references to left
and right.
Unplug the refrigerator from its electrical outlet.
Empty all door shelves, including the dairy compartment.
IMPORTANT NOTES
Installation Instructions
REMOVE THE REFRIGERATOR
DOOR (TOP DOOR)
1
7/32,″ 5/16″ and 3/8″
socket wrench (6-point sockets
are recommended)
TOOLS YOU WILL NEED
Phillips screwdriver
Putty knife or
thin-blade screwdriver
Tape the door shut with masking tape.
Remove the hinge cover. With a 5/16″ socket
wrench, remove the two screws that hold the top
hinge to the cabinet.
Lift the hinge straight up to free the hinge pin from
the socket in the top of the door.
Remove tape, tilt the door away from the cabinet and
lift it to free its bottom socket from the hinge pin on
the center hinge bracket.
Set the door on a non-scratching surface with the
outside up.
Masking tape
T-20 or T-25 Torx Driver,
whichever your model
requires
14
Read these instructions completely and carefully.
REMOVE THE FREEZER DOOR
(BOTTOM DOOR) (For freezer
swing door models only)
2
Tape the door shut with masking tape.
Remove the hinge pin
with a 7/32″ socket
wrench.
Remove tape and tilt the
door away from the cabinet.
Remove and save the
washer on the hinge pin.
Lift the door straight up
to free its bottom socket
from the pin in the
bottom hinge bracket.
REMOVE CENTER HINGE PIN
(For models with a freezer drawer)
Remove the hinge pin with a 7/32″ socket wrench.
Plastic washer
Hinge pin
Center hinge
bracket
Freezer door
15
Installation Instructions
TRANSFER CENTER HINGE
BRACKET TO THE LEFT
Remove the center hinge bracket and shim by
removing the three screws. NOTE: Keep these screws
with the hinge bracket. They are longer screws and will
be used when installing the hinge on the other side.
Remove the three painted screws and take washers
from the center left side of the cabinet. Screw them
into the holes on the right side, which were uncovered
above.
Place the center hinge bracket and shim over the holes
at the center left side of the cabinet. Insert the three
screws that were removed with the center hinge bracket
at the beginning of Step 4 and tighten securely.
Do not install the hinge pin yet.
4
TRANSFER BOTTOM HINGE
BRACKET TO THE LEFT (For
freezer swing door models only)
Pull the base grille straight out to gain access to the
hinge bracket screws.
Using a 5/16″ socket wrench, remove the hinge
bracket, screws, plastic washer and spacer shim from
the bottom right side of the cabinet.
Reinstall the spacer shim, hinge bracket, screws and
plastic washer to the bottom left side of the cabinet.
Remove the cap from the left end of the base grille.
Install the cap, supplied inside the kit, on the right
end of the base grille. Reinstall the base grille and
push it firmly into place.
3
TRANSFER TOP HINGE
TO THE LEFT
Interchange hinge and shim at top right with two
plug buttons at top left of cabinet. Do not tighten
screws on hinge side at this time.
5
REVERSING THE DOOR SWING (CONT.)
Installation Instructions
16
TRANSFER DOOR STOPS
On each door, remove the metal door stop. Use the
center hinge pin as a guide to align the door stop,
supplied inside the kit, on the opposite side, after
reversing the handles.
On freezer drawer models, only the refrigerator door
has a door stop.
6
TRANSFER REFRIGERATOR
DOOR HANDLE TO THE RIGHT
Remove the four handle mounting screws. On some
models, you must first remove the screw covers.
Using a putty knife, remove the four screw hole plug
buttons from the right side of the door.
Reinstall the plug buttons on the left side of the door.
Align the handle over the holes in the right side of
the door and install the four mounting screws and
screw covers (on some models).
At the top of the door, remove the plug button using
a putty knife and reinstall it in the top right hand
side hole.
One of the illustrations below will look like your
refrigerator door handle.
NOTE: Make sure the door stop on the bottom of
the door has been transferred to the left side of the
door as explained in step 6.
8
PREPARE FREEZER HANDLE
FOR DOOR SWING CHANGE (For
freezer swing door models only)
One of the illustrations below will look like your
freezer door handle.
Remove the four handle mounting screws. Remove
the plug button and plug button retainer and transfer
them to the opposite side. Reinstall handle.
Remove the plug button and transfer it to the
opposite side.
NOTE: Make sure the door stop on the bottom of the
door has been transferred to the left side of the door
as explained in step 6.
7
Plug button
Plug button
retainer
Plug button
Refrigerator
door
Handle
mounting
screws
Handle
Plug button
Refrigerator
door
Handle
mounting
screws
Handle
Plug button
Handle
mounting
screws
Installation Instructions
REHANG FREEZER DOOR (For
freezer swing door models only)
Lower bottom socket of freezer door onto pin on
bottom hinge bracket. Be sure washer is in place.
Tilt door toward cabinet and gently push door under
center hinge bracket and align with the hole in the
center hinge bracket.
Reinstall hinge pin with a 7/32″ socket wrench so it
extends through the hole in the center hinge bracket
and into socket on top of freezer door.
9
REHANG REFRIGERATOR DOOR
Lower bottom socket of the refrigerator door onto
center hinge pin. Be sure washer is in place.
Tilt door toward cabinet, lifting the top hinge so the
pin fits into the socket on top of the door.
Tighten the top hinge screws after supporting the
door on the handle side and ensuring the gap
between the doors is even all across the front.
Replace the hinge cover.
10
17
Plastic washer
Hinge pin
Center hinge
bracket
Freezer door
REPLACE CENTER HINGE PIN
(For models with a freezer drawer)
Reinstall hinge pin with a 7/32″ socket wrench
so it extends through the hole in the center hinge
bracket.
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
18
Normal operating sounds.
Depending on the placement of the refrigerator in your kitchen,
you may want to place a piece of rubber backed carpet under
the refrigerator to reduce noise.
Evaporator Fan. You may hear air being forced through the cabinet
by the fan.
Evaporator. The flow of refrigerant through the evaporator may create a
boiling or gurgling sound.
Defrost Heater. During defrost cycles, water dripping onto the heater may
cause a hissing or sizzling sound. After defrosting, a popping sound may
occur and the evaporator may create a boiling or gurgling sound.
Cold Control & Defrost Timer. These parts can produce a snapping sound
when turning the refrigerator on or off. The timer also produces a sound
similar to an electric clock.
Water Pan. Water may be heard running into the drain pan during the
defrost cycle.
Compressor. Modern, high efficiency compressors operate much faster
than older models. The compressor may have a high pitched hum or
pulsating sound.
Condenser Fan. You may hear air being forced over the condenser by the fan.
Before you call for service…
Troubleshooting Tips
Save time and money! Review the charts on the following
pages first and you may not need to call for service.
Problem Possible Causes What To Do
Refrigerator does not Refrigerator in defrost cycle. • Wait about 45 minutes for defrost cycle to end.
operate
Control in OFF position. • Move the control to a temperature setting.
Refrigerator is unplugged. • Push the plug completely into the outlet.
The fuse is blown/circuit • Replace fuse or reset the breaker.
breaker is tripped.
Vibration or rattling Rollers need adjusting. • See Preparing to Install the Refrigerator.
(slight vibration
is normal)
1
2
3
4
5
6
7
GEAppliances.com
Problem Possible Causes What To Do
Motor operates for Normal when refrigerator • Wait 24 hours for the refrigerator to completely
long periods or cycles is first plugged in. cool down.
on and off frequently.
Often occurs when large • This is normal.
(Modern refrigerators
amounts of food are
with more storage
placed in refrigerator.
space and a larger
Door left open. • Check to see if package is holding door open.
freezer require more
• Rollers must be properly adjusted so doors/drawers
operating time. They
will close automatically when partially open. See
start and stop often
Preparing to Install the Refrigerator.
to maintain even
Hot weather or frequent • This is normal.
door openings.
Temperature control • See Getting started.
set at the coldest setting.
Refrigerator or freezer Temperature controls not set • See Getting started.
compartment too warm cold enough.
Warm weather or frequent • Set the temperature control one step colder.
door openings. See Getting started.
Door left open. • Check to see if package is holding door open.
• Rollers must be properly adjusted so doors/drawers
will close automatically when partially open. See
Preparing to Install the Refrigerator.
Frost or ice crystals Door left open. • Check to see if package is holding door open.
on frozen food
• Rollers must be properly adjusted so doors/drawers
(frost within package
will close automatically when partially open. See
is normal)
Preparing to Install the Refrigerator.
Too frequent or too long
door openings.
Ice cubes have Food transmitting odor/taste • Wrap foods well.
odor/taste to ice cubes.
Interior of refrigerator •See Care and cleaning.
needs cleaning.
Slow ice cube freezing Door left open. • Check to see if package is holding door open.
• Rollers must be properly adjusted so doors/drawers
will close automatically when partially open. See
Preparing to Install the Refrigerator.
Freezer control not set • See Getting started.
cold enough.
Refrigerator has odor Foods transmitting • Foods with strong odors should be tightly wrapped.
odor to refrigerator.
• Keep an open box of baking soda in the refrigerator;
replace every three months.
Interior needs cleaning. • See Care and cleaning.
temperatures.)
19
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
20
Before you call for service…
Problem Possible Causes What To Do
Moisture forms on Not unusual during • Wipe surface dry and reset the refrigerator control
outside of refrigerator periods of high humidity. one setting colder.
Moisture collects inside Too frequent or too
(in humid weather, air long door openings.
carries moisture into
refrigerator when doors
are opened)
Food freezing in Food too close to air vent. • Move the food away from the air vent (near the controls).
the refrigerator
Refrigerator control is set • Move the refrigerator control to a warmer temperature.
too cold.
Door/drawer does not Rollers need adjusting. •See Preparing to Install the Refrigerator.
close by itself
Interior light does No power at outlet. • Replace fuse or reset the breaker.
not work
Light bulb burned out. •See Replacing the light bulbs.
Door squeaks when Hinge and/or gasket needs
opened lubrication.
Freezer door/drawer This is normal if, after popping • This indicates that there is a good seal on the freezer
pops open when open, the freezer door/drawer door/drawer. If the freezer door/drawer does not
refrigerator door closed on its own. automatically close after popping open, then see the
is closed Problem: Door/drawer does not close by itself, above.
Icemaker power switch Freezer door/drawer is open. •This is normal. Power to the icemaker is interrupted
is in the I (on) position, when the freezer door/drawer is open to prevent ice
but green power light from ejecting and dropping into the back of the freezer.
is not on To check if icemaker is working properly, press the
freezer light switch located on the upper right side
of the freezer. The green power light will come on.
Water is spilling out Freezer door/drawer was • Clean up spill, then shut the freezer door/drawer and
of icemaker mold opened shortly after icemaker do not open for approximately 4 hours. This will allow
was installed. the freezer to reach the correct operating temperature
for making ice.
Freezer door left open for an • Because of door openings, freezer could not maintain
extended period, then opened the correct operating temperature for making ice. Clean
and closed frequently soon after. up spill, then shut the freezer door/drawer and do not
open for approximately 4 hours.
Cubes too small/ Not enough water pressure • Collar type self-piercing water valves are not
reduced ice production to icemaker water valve. recommended unless a 1/4″ hole is predrilled in home
water line. See Installing the Water Line instructions in
the Icemaker Accessory Kit Installation Instructions.
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
Troubleshooting Tips
Installation Instructions Safety InstructionsOperating Instructions
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
dans d''autres langues
- English: GE Model 18 User manual
Documents connexes
-
GE GDS18LBRCC Le manuel du propriétaire
-
-
GE TBX12SAXLAD Le manuel du propriétaire
-
-
GE AJCH 12 Le manuel du propriétaire
-
GE Profile Series PGSS5 Le manuel du propriétaire
-
Cafe™ CFCP1 Manuel utilisateur
-
-
GE Cafe Series CWS21SSESS Le manuel du propriétaire
-
GE PGSS5NFZSS Le manuel du propriétaire