TP-LINK WBS510 Guide d'installation

Marque: TP-LINK

Modèle: WBS510

Catégorie: Antennes réseau

Taper: Guide d'installation

Installation Guide

Outdoor Wireless Base Station

WBS210/WBS510

For technical support, User Guide and other information, please visit

http://www.tp-link.com/support, or simply scan the QR code.

7106507787 REV2.1.3

The products of TP-Link partly contain software code developed by third parties, including

software code subject to the GNU General Public License (“GPL”). As applicable, the terms of the

GPL and any information on obtaining access to the respective GPL Code used in TP-Link

products are available to you in GPL-Code-Centre under (http://www.tp-link.com/en/support/gpl/).

The respective programs are distributed WITHOUT ANY WARRANTY and are subject to the

copyrights of one or more authors. For details, see the GPL Code and other terms of the GPL.

Contents

Overview

Hardware Installation

Connect cables

Mount Base Station

Power On

Lightning and ESD Protection

Configuration with PharOS

Configure the Base Station

Installer Compliance Responsibility

Specification

FAQ

TP-Link's Outdoor Wireless Base Stations of the Pharos series

products are designed for outdoor wireless network solutions,

aiming at long-distance transmission and large coverage of

wireless network.

Overview

Package Contents

Base Station

Metal Strap

Passive PoE Adapter

Power Cord

Waterproof Rubber Insert

Installation Guide

Outdoor Wireless Base Station

WBS210/WBS510

The panel of Base Station

Panel Layout

AP/AP Router mode: All four LEDs remain solid.

Client/Bridge/Repeater/AP Client Router mode:

The more lit LEDs indicate the better wireless signal strength.

On: The port is connected but not active.

Flashing: The port is transmitting data.

On: The Base Station is powered on.

LED Explanation

RESET

Shielded Ethernet

Port LAN1

Shielded Ethernet

Port LAN0(POE IN)

Grounding Terminal

LAN1

LAN0(POE IN)

GND

Chain1 Chain0

POWERLAN0LAN1

Passive PoE Adapter

Hardware Installation

The Outdoor Wireless Base Stations require external antenna

that corresponds to your network environment. It is

recommended to buy and use TP-Link’s matching antennas.

Power LED:

The Power LED indicates the

status of the electric current:

Green: 0-0.8A , Red: 0.8-1A

Remote Reset:

Press and hold for 8 seconds to

reset the Base Station to its

factory defaults.

Step3:

Affix the waterproof rubber insert

to the underside of the device for

waterproofing and replace the

cover until it firmly locks into place.

Step4:

Connect the RF Cables to the

Base Station.

Step1:

Firmly grasp the rear of the interface

cover and pull it downward.

Connect Cables

Step2:

Use an adequate Ethernet cable to

connect the LAN0 (POE IN) port. The

length of cable is up to 60m for steady

power supply. Shielded CAT5e (or

above) cable with an integrated ground

wire is recommended.

Step3:

Attach the protective cap. Push

and slide the protective cap down

over the Base Station until it firmly

locks into place.

Step1:

Align the mounting tabs on the back

of the Base Station with the four slots

of the mounting bracket. Push and

slide the Base Station downward until

it locks into place.

Step2:

Connect the RF cables from the Base

Station to the corresponding

connectors on the antenna.

Note: Sector antenna is used as a demonstration below.

Mount Base Station

Option1: Mounting the Base Station on an Antenna

Mount the Base Station on an antenna with a suitable mounting

bracket or on a pole for the antenna without the mounting

bracket.

Step1:

Loosen and completely remove the

end of the metal strap by turning the

captive screw counterclockwise with a

flathead screwdriver.

Step2:

Lead the end of the metal strap

through the back of the Base Station.

Step3:

Position the Base Station and wrap

the metal strap around the pole. Feed

the end back through the screw-block

and turn the screw clockwise to

tighten the metal strap using a

flathead screwdriver until the Base

Station is secure.

Step4:

Connect the RF cables from the Base Station to the

corresponding connectors on the antenna.

Option 2: Mounting the Base Station on a Pole

Step1:

Connect the Ethernet cable from the Base Station to the POE

port of the PoE adapter.

Step2:

Connect an Ethernet cable from your LAN device (a computer,

router or switch) to the LAN port on the PoE adapter.

Step3:

Connect the power cord to the power port on the PoE adapter

and plug it into an electrical outlet.

Connect the Base Station to a Power over Ethernet (PoE)

adapter as follows:

Power On

PoE LAN

Ethernet cable length up to 60m

Lightning and ESD Protection

Option A

Use a shielded CAT5e (or above) cable with an integrated

grounding wire for connection.

Option B

If you have the standard CAT5e cable for the connection, use a

separate grounding cable to connect the grounding Terminal

(GND) to earth ground.

Proper grounding is extremely important for outdoor devices.

There are two effective techniques for grounding the Base

Station.

Grounding

Terminal

Earth Ground

Grounding

Cable

Grounded 3-wire

Power Outlet

Grounded PoE

Adapter

Shielded CAT5e (or above)

Cable with

an Integrated

Grounding Wire

Base Station

Open a web browser, type http://192.168.0.254 into the

address field and press Enter (Windows) or return (Mac). It is

recommended to use the latest version of Google Chrome,

Firefox or Safari.

Conguration with PharOS

Before accessing the PharOS Web Interface, you need to

assign a static IP address 192.168.0.X (X ranges between 2

and 253, e.g. 192.168.0.10) to your computer.

Based on your network needs, this section will guide you

through the Base Station configuration using PharOS, a

web-based management system that allows you to do more

specific configurations.

192.168.0.254

Change

the

default

User

Name

and

Password

protect

your

Base Station. Let’s start configuring the Base Staion.

1. Log in to PharOS and go to the Quick Setup page.

2. Operation Mode: Select Access Point and click Next.

3. LAN Settings: Click Next.

4. Wireless AP Settings:

a. Create a new SSID (Network name) for your wireless

network.

b. Select WPA-PSK/WPA2-PSK for the Security method and

create a PSK Password to protect your AP.

c. Enter the distance between the Access Point and the

Client into the Distance Setting field.

d. Select the MAXtream checkbox (Refer to Q2 in FAQ for

details about MAXtream), and click Next.

5. Finish: Verify your settings and click Finish to complete the

configuration.

Congure the Access Point (AP)

For subsequent logins, use the new username and password.

Access point

LAN:192.168.0.254

Client

LAN:192.168.0.2

Congure the Base Station

The typical topology is as follows. A wireless bridge is built

between two locations that are far from each other. Follow the

instructions below to configure the Access Point and the Client.

Enter admin for both User Name and Password, then select

the Language from the drop-down list. Read and agree the

Congure the Client

1. Log in to PharOS and go to the Quick Setup page.

2. Operation Mode: Select Client and click Next.

3. LAN Settings: Change the IP Address to 192.168.0.X (X

ranges between 2 and 253), the same subnet with the

access point, and click Next.

4. Wireless Client Settings:

a. Click Survey and select the SSID of the Access Point in

the AP list, then click Connect.

Select WPA-PSK/WPA2-PSK from the Security option,

enter the same PSK password and distance value of the

Access Point, then click Next.

5. Finish: Verify your settings and click Finish to complete the

configuration.

Devices must be professionally installed and it is the

professional installer's responsibility to make sure the device is

operated within local country regulatory requirements.

Since PharOS can be paired with a variety of antennas, the

Antenna Gain and Output Power fields are provided to the

professional installer to assist in meeting regulatory

requirements

Installer Compliance Responsibility

Specication

Interface

Dimensions

Power Supply

ESD Protection

Lightning Protection

Operating Humidity

Operating Temperature

Certication

LAN0 (POE IN): 10/100Mbps Ethernet port

LAN1: 10/100Mbps Ethernet port

GND: Grounding terminal for lightning

protection

RESET: Button to restore the device to its

factory defaults

Chain0/Chain1: 2 RP-SMA antenna interfaces

24V passive PoE adapter included

15kV

Up to 6kV

-40 to70 (-40 to 158

)

10% to 90%

CE, FCC, RoHS, IP65

198*74*40mm

802.11 Standards

Estimation is based on copper grounding cable and shielded CAT5e(or

above) cable with an integrated grounding wire.

11b/g/n

11a/n

(WBS210)

(WBS510)

Connector

RP-SMA Female

FAQ

How to restore the Base Station to its factory default

settings?

With the Base Station powered on, press and hold the

RESET button on the Base Station or the Remote Reset

button on the passive PoE adapter for about 8 seconds

until the Wireless Signal Strength LEDs flash.

What is Pharos MAXtream?

Pharos MAXtream is a proprietary protocol developed on

the basis of Time Division Multiple Access (TDMA) by

TP-Link.

The MAXtream technology has the following advantages:

Eliminates hidden node collisions & improves channel

efficiency.

Lower latency, higher throughput, larger network capacity &

more stability.

Improves the QoS for video, voice and sound data stream.

By dividing the timing of transmission into different time

slots, MAXtream allows the Pharos devices to transmit in

rapid succession, one after another, each using its own

time slot to transmit and receive they own frames, which

greatly reduces the chance of collision.

Pharos MAXtream is a non-standard Wi-Fi protocol that is

only compatible with TP-Link’s Pharos series products.

Please notice that you will not be able to connect other

Wi-Fi devices to an AP with MAXtream enabled.

Q2.

Q1.

Note:

The select box of Frequency Range at the top-left corner is only

available for WBS510. Select the desired range and then click Start.

Click Start, the PharOS will begin to analyze the power of

frequency

. Observe the curves for a period of time, and

then click stop. Note that the relatively low and continuous

part of the average curve indicates less radio noise. Here,

we use the figure below as an example.

When choosing channel/frequency, you should avoid the

spectrum with large radio noise. In this example, the

recommended channel/ frequency is 112/5560MHz.

drop-down list,

a window will pop up to remind you that all

wireless connections

will be lost during spectrum analysis.

Click Yes to continue to the Spectrum Analysis page.

How can I use Spectrum Analysis to find the

appropriate channel for the devices?

Q3.

FCC STATEMENT

CE Mark Warning

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment. This device and its antenna must not be co-located or

operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is

applicable to only Mobile Configurations. The antennas used for this transmitter

must be installed to provide a separation distance of at least 20 cm from all

persons and must not be co-located or operating in conjunction with any other

antenna or transmitter.”

void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused

by unauthorized modifications to this equipment. Such modifications could void

the user’s authority to operate the equipment.

This is a class A product. In a domestic environment, this product may cause radio

interference, in which case the user may be required to take adequate measures.

This equipment has been tested and found to comply with the limits for a Class A

digital device,pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. Thisequipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that

may cause undesired operation.

IC STATEMENT

This device meets the EU requirements (1999/5/EC Article 3.1a) on the limitation of

exposure of the general public to electromagnetic fields by way of health

protection.

RF Exposure Information

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Canadian Compliance Statement

This device complies with Industry Canada license-exempt RSSs. Operation is

subject to the following two conditions:

1 This device may not cause interference, and

2 This device must accept any interference, including interference that may

cause undesired operation of the device.

This radio transmitter (IC: 8853A-WBS210/Model: WBS210 and IC:

8853A-WBS510/Model: WBS510) has been approved by Industry Canada to

operate with the antenna types listed below with the maximum permissible gain

and required antenna impedance for each antenna type indicated. Antenna types

not included in this list, having a gain greater than the maximum gain indicated for

that type, are strictly prohibited for use with this device.

Canadian Compliance Statement

To reduce potential radio interference to other users, the antenna type and its gain

should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not

more than that permitted for successful communication.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux

appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes :

1 l’appareil ne doit pas produire de brouillage;

2 l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

meme si le brouillage est susceptible d’en compromettre le fonctionnement.

Cet émetteur radio (IC: 8853A-WBS210/Model: WBS210 and IC:

8853A-WBS510/Model: WBS510) a été approuvée par Industrie Canada pour

l’exploitation avec l’antenne types énumérés ci-dessous avec le gain maximal

admissible et requis l’impédance de l’antenne pour chaque type d’antenne indiqué.

Types d’antenne non inclus dans cette liste, ayant un gain supérieur au gain

maximal indiqué pour ce type, sont strictement interdits pour une utilisation avec

cet appareil. Immédiatement suite à la remarque, le fabricant doit fournir une liste

de tous les types d’antenne approuvé pour une utilisation avec l’émetteur, ce qui

indique le gain

maximal d’antenne permis (en dBi) et requis d’impédance pour chacun.

Pour réduire le risque d’interférence aux autres utilisateurs, le type d’antenne et son

gain doivent être choisies de façon que la puissance isotrope rayonnée

équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication

réussie.

WBS210 (8853A-WBS210)

2 dBi omni (50 ohm)

15 dBi sector (50 ohm)

WBS510 (8853A-WBS510)

3 dBi omni (50 ohm)

19 dBi sector (50 ohm)

Model

Antenna

WBS210 (8853A-WBS210)

2 dBi omni (50 ohm)

15 dBi sector (50 ohm)

WBS510 (8853A-WBS510)

3 dBi omni (50 ohm)

19 dBi sector (50 ohm)

Model

Antenna

Caution (For WBS510)

1 The device for operation in the band 5150–5250 MHz is only for indoor use to

reduce the potential for harmful interference to co-channel mobile satellite

systems;

2 For devices with detachable antenna(s), the maximum antenna gain permitted

for devices in the band 5725-5850 MHz shall be such that the equipment still

complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point

operation as appropriate.

Avertissement (For WBS510)

1 Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé

uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage

préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;

2 Le gain maximal d'antenne permis pour les dispositifs avec antenne(s)

amovible(s) utilisant la bande 5725-5850 MHz doit se conformer à la limitation

P.I.R.E spécifiée pour l’exploitation point à point et non point à point, selon le cas.

Radiation Exposure Statement

This equipment complies with IC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

minimum distance 20cm between the radiator & your body.

Déclaration d'exposition aux radiations

Cet équipement est conforme aux limites d'exposition aux rayonnements IC

établies pour un environnement non contrôlé. Cet équipement doit être installé et

utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et

votre corps.

Industry Canada Statement

CAN ICES-3 (A)/NMB-3(A)

NCC Notice & BSMI Notice

注意！

安全諮詢及注意事項

依據低功率電波輻射性電機管理辦法

第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者

均不得擅自變更頻率、加大功率或變更原設計之特性或功能。

第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有

干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，

指依電信規定作業之無線電信。低功率射頻電機需忍受合法通信或工業、科學

以及醫療用電波輻射性電機設備之干擾。

請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

● 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

● 注意防潮，請勿將水或其他液體潑灑到本產品上。

● 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆

蓋開口。

● 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉

位置中。

● 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此

項工作。

此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種

情況下，使用者會被要求採取某些適當的對策。

AT / BE / BG / CH / CY / CZ / DE / DK / EE / ES / FI / FR / GB / GR / HR / HU

/ IE / IS / IT / LI / LT / LV / MT / NL / NO / PL / PT / RO / SE / SI / SK

For EU/EFTA, this product can be used in the following countries (For WBS510):

Safety Information

When product has a power button, the power button is one of the way to shut

off the product; When there is no power button, the only way to completely shut

off power is to disconnect the product or the power adapter from the power

source.

Don’t disassemble the product, or make repairs yourself. You run the risk of

electric shock and voiding the limited warranty. If you need service, please

Avoid water and wet locations.

Use only power supplies which are provided by manufacturer and in the

original packing of this product. If you have any questions, please don't hesitate

to contact us.

•

La page charge ...

TP-LINK WBS510 Guide d'installation

Marque: TP-LINK

Modèle: WBS510

Catégorie: Antennes réseau

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: TP-LINK WBS510 Installation guide

TP-LINK WBS510 Guide d'installation

TP-LINK WBS510 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents