3M PROTECTA® Self Retracting Lifeline - Web 3100433, Red, 20 ft. (6.1 m), 1 EA Mode d'emploi

3M
Marque
3M
Modèle
PROTECTA® Self Retracting Lifeline - Web 3100433, Red, 20 ft. (6.1 m), 1 EA
Taper
Mode d'emploi

Ce manuel convient également à

© Copyright 2015, Capital Safety
ANSI Z359.14 Class B
ANSI A10.32
CSA Z259.2.2-98 Type 1 and Type 2
OSHA
This manual is intended to meet the Manufacturer’s
Instructions as required by the above listed standards
and should be used as part of an employee training
program as required by OSHA.
INSTRUCTION MANUAL
Figure 1 – Rebel™ Self Retracting Lifeline Models
10 ft (3.0m)
11 ft (3.3m)
20 ft (6.0m)
A - Steel Carabiner
B - Steel Snap Hook
C - Steel Swiveling Snap Hook
D - Steel Rebar Hook
Swivel End Lifeline End
Model Swivel
End
Lifeline
End
A
B
C
D
ANSI
3100425 11 ft (3.3m) 1 1
3100426 11 ft (3.3m) 1 1
3100427 11 ft (3.3m) 1 1
3100431 20 ft (6.0m) 1 1
3100432 20 ft (6.0m) 1 1
3100433 20 ft (6.0m) 1 1
CSA
Type 1
3100428 10 ft (3.0m) 1 1
3100429 10 ft (3.0m) 1 1
3100430 10 ft (3.0m) 1 1
Type 2
3100434 20 ft (6.0m) 1 1
3100435 20 ft (6.0m) 1 1
3100436 20 ft (6.0m) 1 1
Trusted Quality Fall Protection
FORM NO: 5903764
REV: B
SELF RETRACTING LIFELINES
Model Numbers: (See Figure 1)
2
WARNING: This product is part of a personal fall arrest, work positioning, or rescue system. The user must follow the
manufacturer’s instructions for each component of the system. These instructions must be provided to the user of this
equipment. The user must read and understand these instructions before using this equipment. Manufacturer’s instructions
must be followed for proper use and maintenance of this equipment. Alterations or misuse of this product or failure to follow
instructions may result in serious injury or death.
IMPORTANT: If you have questions on the use, care, or suitability of this equipment for your application, contact Capital
Safety.
IMPORTANT: Before using this equipment, record the product identication information from the ID label in the inspection
and maintenance log of this manual.
descRIPTIONs:
Rebel SRLs are available in 10 ft. (3.0m) (CSA only), 11 ft. (3.3m) (ANSI only), and 20 ft. (6.0m) (CSA and ANSI) lifeline
lengths (See Figure 1). Rebel SRLs are equipped with an in-line Energy Absorber which retracts into a Thermoplastic Housing.
The Rebel SRL automatically locks at the onset of a fall to arrest the fall, but pays out and retracts lifeline during normal
movement by the attached user. Figure 2 illustrates key components of the base Rebel™ Self Retracting Lifeline (SRL).
Figure 2 – Rebel Self Retracting Lifeline (SRL) Components
B
D
F
G
A
C
E
A - Swivel B -Swivel Eye C - Carabiner D - Housing E - Web Lifeline F - Energy Absorber G - Snap Hook
3
1.0 APPLICATIONS
1.1 PURPOSE: Capital Safety Self Retracting Lifelines (SRLs) are designed to be a component in a personal fall arrest system
(PFAS). Figure 1 illustrates SRLs covered by this instruction manual and their typical applications. They may be used
in most situations where a combination of worker mobility and fall protection is required (i.e. inspection work, general
construction, maintenance work, oil production, conned space work, etc.).
1.2 STANDARDS: Your SRL conforms to the national standard(s) identied on the front cover of these instructions. Refer
to local, state, province, and national requirements governing occupational safety for additional information regarding
Personal Fall Arrest Systems. Refer to the following national standards on fall protection:
ANSI Z359.0 Denitions and Nomenclature Used for Fall
Protection and Fall Arrest
ANSI ANSI
A10.32
Personal Fall Protection use in
Construction and Demolition
ANSI Z359.1 Safety Requirements for Personal Fall Arrest
Systems, Subsystems, and Components
CSA Z359.2.2 Self-Retracting Devices for Personal Fall
Arrest Systems
ANSI Z359.2 Minimum Requirements for a Comprehensive
Managed Fall Protection Program
1.3 TRAINING: This equipment is intended to be used by persons trained in its correct application and use. It is the
responsibility of the user to assure they are familiar with these instructions and are trained in the correct care and use
of this equipment. Users must also be aware of the operating characteristics, application limits, and the consequences of
improper use.
2.0 LIMITATIONS & REQUIREMENTS
Always consider the following limitations and requirements when installing or using this equipment:
2.1 CAPACITY: SRLs are designed for use by one person with a combined weight (person, clothing, tools, etc.) not exceeding
310 lbs (140 kg) and at least 75 lbs (34 kg).
At no time shall more than one person connect to a single SRL for fall arrest applications.
2.2 MAXIMUM ARREST FORCE AND MAXIMUM ARREST DISTANCE: SRLs documented in this instruction meet the following
Arrest Force and Arrest Distance maximums:
Weight of Worker Average Arresting Force Maximum Arresting Force Maximum Arrest Distance
Up to 310 lbs (140 kg) 900 lbs (4.0 kN) 1,350 lbs (6.0 kN) 42 in (1.07 m)
2.3 ANCHORAGE: Anchorages selected for fall arrest systems shall have a strength capable of sustaining static loads applied
in the directions permitted by the system of at least:
1. 5,000 lbs. (22.2 kN) for non-certied anchorages, or
2. Two times the maximum arresting force for certied anchorages.
When more than one fall arrest system is attached to an anchorage, the strengths set forth in (1) and (2) above shall be
multiplied by the number of systems attached to the anchorage.
NOTE: Anchorages used for attachment of personal fall arrest systems shall be independent of any anchorage being used
to support or suspend platforms, and capable of supporting at least 5,000 lbs. per user attached, or be designed, installed,
and used as part of a complete personal fall arrest systems which maintains a safety factor of at least two, and is under the
supervision of a qualied person.
2.4 RESCUE PLAN: When using this equipment, the employer must have a rescue plan and the means at hand to implement
it and communicate that plan to users, authorized persons, and rescuers.
2.5 INSPECTION FREQUENCY:
Table 1 indicates inspection frequency. SRLs shall be inspected by the Authorized Person
1
or
Rescuer
2
before each use (See Table 2). Additionally, inspections shall be conducted by a Competent Person
3
other than
the user, and by a factory authorized inspection entity.
NOTE: CSA Z259.2.2 Type 2 SRLs must be submitted to a Capital Safety Authorized Service Agent within 2 years of
the date of manufacture for inspection and maintenance, and annually thereafter. The Authorized Service Agent will
record their findings and label the product with the next annual service date.
Table 1 – Inspection Schedule
Type of Use
Application
Examples Conditions of Use
Inspection Frequency
Competent
Person
User
Infrequent to Light Rescue and
Conned
Space, Factory
Maintenance
Good Storage Conditions, Indoor or Infrequent
Outdoor Use, Room Temperature, Clean
Environments
Annually Before each use
Moderate to Heavy Transportation,
Residential
Construction,
Utilities, Warehouse
Fair Storage Conditions, Indoor and Extended
Outdoor Use, All Temperatures, Clean or Dusty
Environments
Semi-Annually
to Annually
Before each use
Severe to
Continuous
Commercial
Construction, Oil
and Gas, Mining
Harsh Storage Conditions, Prolonged or
Continuous Outdoor Use, All Temperatures,
Dirty Environment
Quarterly to
Semi-Annually
Before each use
1 Authorized Person: A person assigned by the employer to perform duties at a location where the person will be exposed to a fall hazard.
2 Rescuer: Person or persons other than the rescue subject acting to perform an assisted rescue by operation of a rescue system.
3 Competent Person: An individual designated by the employer to be responsible for the immediate supervision, implementation, and monitoring
of the employer’s managed fall protection program who, through training and knowledge, is capable of identifying, evaluating, and addressing
existing and potential fall hazards, and who has the employer’s authority to take prompt corrective action with regard to such hazards
.
4
Results of the Authorized Service or Competent Person inspection should be recorded in the “Inspection and Maintenance
Log” at the back of these instructions (see Section 5).
2.6 LOCKING SPEED: Situations which do not allow for an unobstructed fall path should be avoided. Working in confined
or cramped spaces may not allow the body to reach sufficient speed to cause the SRL to lock if a fall occurs. Working on
slowly shifting material, such as sand or grain, may not allow enough speed buildup to cause the SRL to lock. A clear path
is required to assure positive locking of the SRL.
2.7 NORMAL OPERATIONS: Normal operation will allow the full length of the lifeline to extend and retract with no hesitation
when extending and no slack when retracting as the worker moves at normal speeds. If a fall occurs, a speed sensing
brake system will activate, stopping the fall and absorbing much of the energy created. For falls which occur near the
end of the lifeline travel, a reserve lifeline system or energy absorber has been incorporated to assure a reduced impact
fall arrest. If the SRL has been subjected to fall forces, remove the SRL from service, mark “UNUSABLE” and send to an
authorized service center for repair. Sudden or quick movements should be avoided during normal work operation, as this
may cause the SRL to lock up.
2.8 FREE FALL: When anchored overhead, SRLs will limit the free fall distance to 2 ft. (0.6 m) or less. To avoid increased fall
distances, anchor the SRL directly above the worker. Avoid working where your lifeline may cross or tangle with that of
another worker. Avoid working where an object may fall and strike the lifeline; resulting in loss of balance or damage to
the lifeline. Do not allow the lifeline to pass under arms or between legs. Never clamp, knot, or prevent the lifeline from
retracting or being taut. Avoid slack line. Do not lengthen SRL by connecting a lanyard or similar component
without consulting Capital Safety.
2.9 SWING FALLS: Swing Falls occur when the anchorage point is not directly above the point where a fall occurs. The force
of striking an object in a swing fall may cause serious injury (see Figure 3A). Minimize swing falls by working as directly
below the anchorage point as possible.
2.10 FALL CLEARANCE: Figure 3B illustrates Fall Clearance. SRL Fall Arrest Systems should have a minimum Fall Clearance of 6 ft
(2 m) for falls from a standing position where the SRL is anchored directly overhead. Falls from a kneeling or crouching position
will require an additional 3 ft (1 m) of Fall Clearance. In a swing fall situation, the total vertical fall distance will be greater
than if the user had fallen directly below the anchorage point and may require additional Fall Clearance. The table in
Figure 3 provides the minimum vertical Fall Clearance needed below the working level of the SRL user where added Swing
Fall distance is within the recommended range of use.
Figure 3 – Fall Clearance and Swing Falls
A
!
WARNING
B
H
V
FC
FC = Minimum Fall Clearance
FC
ft
(m)
H - Horizontal Distance from
Anchorage Point
0
(0.0)
2
(0.6)
4
(1.2)
6
(1.8)
8
(2.4)
10
(3.0)
12
(3.7)
V - Vertical Distance
from Anchorage Point
0
(0.0)
6
(2)
8
(2.6)
û û û û û
10
(3)
6
(2)
6.2
(2.1)
6.8
(2.3)
7.7
(2.6)
8.8
(2.9)
û û
20
(6.1)
6
(2)
6.1
(2)
6.4
(2.1)
6.9
(2.3)
7.5
(2.5)
8.4
(2.7)
9.3
(3)
û Added Swing Fall Length is not within the recommended work zone.
NOTE: Fall Clearance (FC) values in the above table assume a fall from
a standing position. If the worker is kneeling or crouching near an edge
when a fall occurs, an additional 3 ft (1 m) of Fall Clearance is needed.
NOTE: The clearances provided above assume the fall occurs from the standing position. If the worker is kneeling or
crouching an additional 3 ft (1 m) of clearance is needed.
2.11 HAZARDS: Use of this equipment in areas where surrounding hazards exist may require additional precautions to reduce the
possibility of injury to the user or damage to the equipment. Hazards may include, but are not limited to: high heat, caustic
chemicals, corrosive environments, high voltage power lines, explosive or toxic gases, moving machinery, sharp edges, or
overhead materials that may fall and contact the user or fall arrest system.
2.12 SHARP EDGES: Avoid working where the lifeline will be in contact with or abrade against unprotected sharp edges.
Where
contact with a sharp edge is possible, cover the edge with a protective material.
2.13 BODY SUPPORT: A Full Body Harness must be used with the Self Retracting Lifeline. The harness connection point must be
above the user’s center of gravity. A body belt is not authorized for use with the Self Retracting Lifeline. If a fall occurs when
using a body belt it may cause unintentional release or physical trauma from improper body support.
2.14 COMPATIBILITY OF COMPONENTS: Unless otherwise noted, Capital Safety equipment is designed for use with Capital
Safety approved components and subsystems only. Substitutions or replacements made with non approved components
or subsystems may jeopardize compatibility of equipment and may affect safety and reliability of the complete system.
IMPORTANT: Read and follow manufacturer’s instructions for associated components and subsystems in your
personal fall arrest system.
5
2.15 COMPATIBILITY OF CONNECTORS: Connectors are considered to be compatible with connecting elements when they
have been designed to work together in such a way that their sizes and shapes do not cause their gate mechanisms
to inadvertently open regardless of how they become oriented. Contact Capital Safety if you have any questions about
compatibility.
Connectors (hooks, carabiners, and D-rings) must be capable of supporting at least 5,000 lbs. (22.2 kN). Connectors
must be compatible with the anchorage or other system components. Do not use equipment that is not compatible. Non-
compatible connectors may unintentionally disengage (see Figure 4). Connectors must be compatible in size, shape, and
strength. Self-locking snap hooks and carabiners are required by ANSI Z359 and OSHA.
2.16 MAKING CONNECTIONS: Snap hooks and carabiners used with this equipment must be self-locking. Ensure all
connections are compatible in size, shape and strength. Do not use equipment that is not compatible. Ensure all
connectors are fully closed and locked.
Capital Safety connectors (snap hooks and carabiners) are designed to be used only as specied in each
product’s user’s instructions. See Figure 5 for examples of inappropriate connections. Do not connect snap
hooks and carabiners:
A. To a D-ring to which another connector is attached.
B. In a manner that would result in a load on the gate.
NOTE: Large throat snap hooks should not be connected to standard size D-rings or similar objects which will
result in a load on the gate if the hook or D-ring twists or rotates, unless the snap hook complies with ANSI
Z359.1-2007 or ANSI Z359.12 and is equipped with a 3,600 lb (16 kN) gate. Check the marking on your snap hook
to verify that it is appropriate for your application.
C. In a false engagement, where features that protrude from the snap hook or carabiner catch on the
anchor, and without visual conrmation seems to be fully engaged to the anchor point.
D. To each other.
E. Directly to webbing or rope lanyard or tie-back (unless the manufacturer’s instructions for both the
lanyard and connector specically allows such a connection).
F. To any object which is shaped or dimensioned such that the snap hook or carabiner will not close and
lock, or that roll-out could occur.
G. In a manner that does not allow the connector to align properly while under load.
Figure 4 – Unintentional Disengagement Figure 5 – Inappropriate Connections
If the connecting element to which a snap hook (shown) or carabiner attaches
is undersized or irregular in shape, a situation could occur where the connecting
element applies a force to the gate of the snap hook or carabiner. This force may
cause the gate (of either a self-locking or a non-locking snap hook) to open,
allowing the snap hook or carabiner to disengage from the connecting point.
Small ring or other
non-compatibly
shaped element
Force is applied to the
Snap Hook.
The Gate presses against
the Connecting Ring.
The Gate opens allowing
the Snap Hook to slip off.
A. B. C. D.
E. F. G.
6
3.0 InstallatIon
3.1 PLANNING: Plan your fall protection system
before starting your work. Account for all factors
that may affect your safety before, during,
and after a fall. Consider all requirements and
limitations dened in Section 2.
3.2 ANCHORAGE: Figure 6 illustrates typical SRL
anchorage connections. Select an anchorage location
with minimal free fall and swing fall hazards (see
Section 2). Select a rigid anchorage point capable
of sustaining the static loads dened in Section 2.2.
Rebel SRLs must always be anchored at or
above the user’s Dorsal D-Ring.
Important: It is recommended that this
equipment be installed under the supervision
of a qualied person.
4
3.3 HARNESS MOUNTING OPTIONS:
SRL FULL BODY HARNESS MOUNTING:
The Rebel SRL is connected to the harness dorsal
D-Ring using a Snap Hook on the lifeline end (See
Figure 7). The housing swivel end of the Rebel
must be connected to an anchorage point (see
Section 2.3) with the Carabiner (See Figure 7).
Figure 6 – Anchorage Connections
C
A
B
A
B
A - Anchorage B - Connector C - Tie-Off Adapter
4.0 UsE
WarnInG: Do not alter or intentionally misuse this equipment. Consult Capital Safety when using this equipment in
combination with components or subsystems other than those described in this manual. Some subsystem and component
combinations may interfere with the operation of this equipment. Use caution when using this equipment around moving
machinery, electrical hazards, chemical hazards, sharp edges, or overhead materials that may fall onto the lifeline. Do not
loop the lifeline around small structural members
. Failure to heed this warning may result in equipment malfunction, serious
injury, or death.
WarnInG: Consult your doctor if there is reason to doubt your tness to safely absorb the shock from a fall arrest. Age
and tness seriously affect a worker’s ability to withstand falls. Pregnant women or minors must not use self retracting
lifelines.
4.1 BEFORE EACH USE: Before each use of this fall protection equipment carefully inspect it to assure it is in good working
condition. Check for worn or damaged parts. Ensure all fasteners are present and secure. Check that the lifeline is
retracting properly by pulling out the line and allowing it to slowly retract. If there is any hesitation in retraction, remove
the SRL from service, mark “UNUSABLE”, and send to an authorized service center for repair. Inspect the lifeline for cuts,
frays, burns, crushing and corrosion. Check locking action by pulling sharply on the line. See Section 5 for inspection
details.
4.2 AFTER A FALL: Any equipment which has been subjected to the forces of arresting a fall or exhibits damage consistent
with the effect of fall arrest forces as described in Section 5, must be removed from service immediately, marked
“UNUSABLE”, and sent to an authorized service center for repair.
4.3 BODY SUPPORT: A full body harness must be worn when using Rebel SRLs. For general fall protection use, connect to
the back (dorsal) D-ring. For situations such as ladder climbing, it may be useful to connect to the front of the harness
above the worker’s center of gravity. This is acceptable provided potential free fall is less than 2 ft. (61 cm) and footing
can be easily regained.
Important: Do not use a body belt for free fall applications. See OSHA 1926.502 for guidelines.
4 —
Qualied Person: A person with a recognized degree or professional certicate and with extensive knowledge, training, and experience in the
fall protection and rescue eld who is capable of designing, analyzing, evaluating, and specifying fall protections and rescue systems to the
extent required by OSHA and other applicable standards.
7
4.4 MAKING CONNECTIONS: Figure 7 illustrates harness and anchorage connections for Rebel SRL Fall Arrest Systems.
When using a hook to make a connection, ensure roll-out cannot occur (see Figure 4). Do not use hooks or connectors
that will not completely close over the attachment object. Do not use non-locking snap hooks. The anchorage must meet
the anchorage strength requirements stated in section 2.3. Follow the manufacturer’s instructions supplied with each
system component.
4.5 OPERATION: Prior to use, inspect the SRL as described in section 5.0. Figure 7 shows system connections for typical
Rebel SRL applications. Connect the Rebel SRL carabiner to a suitable anchorage. Connect the Hook or Carabiner
on the lifeline end to the Dorsal D-Ring on the Full Body Harness. Ensure connections are compatible in size, shape,
and strength. Ensure hooks are fully closed and locked. Once attached, the worker is free to move about within the
recommended working area at normal speeds. If a fall occurs the SRL will lock and arrest the fall. Upon rescue, remove
the SRL from use. When working with an SRL, always allow the lifeline to recoil back into the device under control.
WarnInG: Do not tie or knot the lifeline. Avoid lifeline contact with sharp or abrasive surfaces. Inspect the lifeline
frequently for cuts, fraying, burns, or signs of chemical damage. Dirt, contaminants, and water can lower dielectric
properties of the lifeline. Use caution near power lines.
4.6 HORIZONTAL SYSTEMS: In applications where the Rebel SRL is used in conjunction with a horizontal system (i.e.
Horizontal Lifeline, Horizontal I-Beams Trolley), the horizontal systems must be designed and installed under the
supervision of a qualied engineer. SRL and horizontal system components must be compatible. Consult the horizontal
system equipment manufacturer’s instructions for details.
Figure 7 – Rebel SRL System Connections
D
C
B
A
A - Dorsal D-Ring B - Snap Hook C - Carabiner D - Anchorage Point
5.0 InspEctIon
5.1 INSPECTION FREQUENCY: The Rebel SRL must be inspected at the intervals dened in “Section 2.5 - Inspection
Frequency”. Inspection procedures are described in the “Inspection Checklist” (Table 2).
5.2 UNSAFE OR DEFECTIVE CONDITIONS: If inspection reveals an unsafe or defective condition, remove the SRL from
service, mark “UNUSABLE” and send to an authorized service center for repair.
5.3 PRODUCT LIFE: The functional life of Rebel SRLs is determined by work conditions and maintenance. As long as the SRL
passes inspection criteria, it may remain in service.
8
6.0 maIntEnancE, sErVIcInG, and storaGE
6.1 CLEANING: Cleaning procedures for the Rebel SRL are as follows:
• Periodically clean the exterior of the SRL using water and a mild soap solution. Position the SRL so
excess water can drain out. Clean labels as required.
• Clean the Web Lifeline with water and mild soap solution. Rinse and thoroughly air dry. Do not force dry
with heat. The lifeline should be dry before allowing it to retract into the housing. An excessive buildup
of dirt, paint, etc. may prevent the lifeline from fully retracting back into the housing causing a potential
free fall hazard.
Important: If the lifeline contacts acids or other caustic chemicals, remove the SRL from service and wash
with water and a mild soap solution. Inspect the SRL per Table 2 before returning to service.
6.2 SERVICE: Rebel SRLs listed within this instruction are not repairable. If the SRL has been subjected to fall force or
inspection reveals an unsafe or defective condition, remove the SRL from service, mark “UNUSABLE” and send to an
authorized service center for repair.
6.3 STORAGE AND TRANSPORT: Store and transport the SRL in a cool, dry, clean environment out of direct sunlight. Avoid
areas where chemical vapors may exist. Thoroughly inspect the SRL after any period of extended storage.
7.0 spEcIFIcatIons
7.1 PERFORMANCE: Your Rebel SRL has been tested and certied to the performance requirements of the standard(s)
identied on the cover of this instruction manual. See “Section 2.0 - Limitations & Requirements” for performance
specications.
7.2 MATERIALS: Material specications for the Rebel SRL are as follows:
Housing: Nylon, UV Resistant Motor Spring: Stainless Steel
Drum: Nylon, Type 6/6, Glass Filled Swivel: Zinc Plated Steel
Fasteners: Zinc Plated Steel Screws; Stainless
Steel Rivets
Lifeline: Polyester Web
Locking Pawls: Stainless Steel Energy Absorber Cover: PVC Tubing
Web: Polyester
Main Shaft: Stainless Steel
End
Connectors:
(See Figure 1)
Gate Opening Gate Strength
Steel Carabiner 11/16 in (17.5 mm) 3,600 lb (16 kN)
Steel Snap Hook 3/4 in (19 mm) 3,600 lb (16 kN)
Steel Swiveling Snap Hook 3/4 in (19 mm) 3,600 lb (16 kN)
Steel Rebar Hook 2 1/4 in (57 mm) 3,600 lb (16 kN)
7.3 LABELING: Figure 11 illustrates Rebel SRL labeling. All labels on the SRL must be present and fully legible.
9
Table 2 – Inspection Checklist
Component: Inspection: Pass Fail
SRL
(Figure 8)
Inspect for loose fasteners and bent or damaged parts.
Inspect the Housing (A) for distortion, cracks, or other damage.
Inspect the Swivel (B) and Swivel Eye (C) and Carabiner (D) for distortion,
cracks, or other damage. The Swivel should be attached securely to the SRL,
but should pivot freely. The Swivel Eye or Integral Connector should rotate
freely in the Swivel.
The Web Lifeline (E) should pull out and retract fully without hesitation or
creating a slack line condition.
Ensure the SRL locks up when the Lifeline is jerked sharply. Lockup should be
positive with no slipping.
All labels must be present and fully legible (see Figure 11).
Inspect the entire SRL for signs of corrosion.
Web Lifeline
(Figure 9)
Inspect the web lifeline for concentrated wear, frayed strands, broken yarn,
burns, cuts, and abrasions. The lifeline must be free of knots throughout its
length. Inspect for excessive soiling, paint build-up, and rust staining. Inspect
for chemical or heat damage indicated by brown, discolored, or brittle areas.
Inspect for ultraviolet damage indicated by discoloration and the presence of
splinters and slivers on the lifeline surface.
Energy Absorber
(Figure 10)
Inspect the Energy Absorber to determine if it has been activated. There
should be no evidence of elongation and the cover should be secure and free
of tears or other damage.
End Connectors
(Figure 1)
Figure 1 identies the End Connectors that should be included on your Rebel
SRL model. Inspect Snap Hooks, Carabiner, Rebar Hooks, etc. for signs of
damage, corrosion, and proper working condition. Where present: Swivels
should rotate freely, and Carabiner and Hook Gates should open, close, lock,
and unlock properly.
Figure 8 – SRL Inspection
B
D
A
C
E
Figure 9 – Web Lifeline
Cut
Frayed
Heavily
Soiled
Welding
Burns
Figure 10 – Energy Absorber
Torn or
Broken
Cover
Deployed and
Torn/Frayed
Webbing
10
Figure 11 – Labeling
10 ft (3.0m)
11 ft (3.3m)
20 ft (6.0m)
INSPECTION AND MAINTENANCE LOG
SERIAL NUMBER:
MODEL NUMBER:
DATE PURCHASED: DATE OF FIRST USE:
INSPECTION DATE INSPECTION ITEMS
NOTED
CORRECTIVE ACTION MAINTENANCE
PERFORMED
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Approved By:
Trusted Quality Fall Protection
ISO
9001
CSG USA & Latin America
3833 SALA Way
Red Wing, MN 55066-5005
Toll Free: 800.328.6146
Phone: 651.388.8282
Fax: 651.388.5065
solutions@capitalsafety.com
CSG Canada
260 Export Boulevard
Mississauga, ON L5S 1Y9
Phone: 905.795.9333
Toll-Free: 800.387.7484
Fax: 888.387.7484
info.ca@capitalsafety.com
CSG Northern Europe
5a Merse Road
North Moons, Moat
Reditch, Worcestershire, UK
B98 9HL
Phone: + 44 (0)1527 548 000
Fax: + 44 (0)1527 591 000
csgne@capitalsafety.com
CSG EMEA
(Europe, Middle East, Africa)
Le Broc Center
Z.I. 1ère Avenue
5600 M B.P. 15
06511 Carros Le Broc Cedex
France
Phone: + 33 4 97 10 00 10
Fax: + 33 4 93 08 79 70
information@capitalsafety.com
CSG Australia & New Zealand
95 Derby Street
Silverwater
Sydney NSW 2128
AUSTRALIA
Phone: +(61) 2 8753 7600
Toll-Free : 1 800 245 002 (AUS)
Toll-Free : 0800 212 505 (NZ)
Fax: +(61) 2 8753 7603
sales@capitalsafety.com.au
CSG Asia
Singapore:
16S, Enterprise Road
Singapore 627666
Phone: +65 - 65587758
Fax: +65 - 65587058
inquiry@capitalsafety.com
Shanghai:
Rm 1406, China Venturetech Plaza
819 Nan Jing Xi Rd,
Shanghai 200041, P R China
Phone: +86 21 62539050
Fax: +86 21 62539060
www.capitalsafety.com
LIMITED LIFETIME WARRANTY
Warranty to End User: D B Industries, Inc., dba CAPITAL SAFETY USA (“CAPITAL SAFETY”)
warrants to the original end user (“End User”) that its products are free from defects in materials and
workmanship under normal use and service. This warranty extends for the lifetime of the product
from the date the product is purchased by the End User, in new and unused condition, from a CAPITAL
SAFETY authorized distributor. CAPITAL SAFETY’S entire liability to End User and End User’s exclusive
remedy under this warranty is limited to the repair or replacement in kind of any defective product
within its lifetime (as CAPITAL SAFETY in its sole discretion determines and deems appropriate). No oral
or written information or advice given by CAPITAL SAFETY, its distributors, directors, offi cers, agents
or employees shall create any diff erent or additional warranties or in any way increase the scope of
this warranty. CAPITAL SAFETY will not accept liability for defects that are the result of product abuse,
misuse, alteration or modifi cation, or for defects that are due to a failure to install, maintain, or use the
product in accordance with the manufacturer’s instructions.
CAPITAL SAFETY’S WARRANTY APPLIES ONLY TO THE END USER. THIS WARRANTY IS THE ONLY
WARRANTY APPLICABLE TO OUR PRODUCTS AND IS IN LIEU OF ALL OTHER WARRANTIES AND
LIABILITIES, EXPRESSED OR IMPLIED. CAPITAL SAFETY EXPRESSLY EXCLUDES AND DISCLAIMS
ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND
SHALL NOT BE LIABLE FOR INCIDENTAL, PUNITIVE OR CONSEQUENTIAL DAMAGES OF ANY NATURE,
INCLUDING WITHOUT LIMITATION, LOST PROFITS, REVENUES, OR PRODUCTIVITY, OR FOR BODILY
INJURY OR DEATH OR LOSS OR DAMAGE TO PROPERTY, UNDER ANY THEORY OF LIABILITY, INCLUDING
WITHOUT LIMITATION, CONTRACT, WARRANTY, STRICT LIABILITY, TORT (INCLUDING NEGLIGENCE) OR
OTHER LEGAL OR EQUITABLE THEORY.
GARANTIE LIMITÉE SUR LA DURÉE DE VIE
Garantie off erte à l’utilisateur fi nal : D B Industries, Inc., dba CAPITAL SAFETY USA (« CAPITAL SAFETY »)
garantit à l’utilisateur fi nal d’origine (« Utilisateur fi nal ») que les produits sont libres de tout défaut matériel et de
fabrication dans des conditions normales d’utilisation et de service. Cette garantie couvre toute la durée de vie du
produit, de sa date d’achat à l’état neuf et inutilisé par l’utilisateur auprès d’un distributeur agréé CAPITAL SAFETY.
La responsabilité intégrale de Capital Safety et le seul recours du Client dans le cadre de cette garantie se limitent
à la réparation ou le remplacement en nature des produits défectueux pendant leur durée de vie (à la seule
discrétion de Capital Safety et selon ce qu’elle juge approprié). Aucun renseignement ou avis oral ou écrit fourni par
CAPITAL SAFETY, ses détaillants, administrateurs, cadres, distributeurs, mandataires ou employés ne représentera
une garantie ou n’augmentera de quelque manière la portée de la présente garantie limitée. CAPITAL SAFETY
n’accepte aucune responsabilité pour les défauts causés par un abus, une utilisation abusive, une altération ou une
modifi cation, ou pour les défauts causés par le non-respect des instructions du fabricant relatives à l’installation,
à l’entretien ou à l’utilisation du produit.
CETTE GARANTIE CAPITAL SAFETY S’APPLIQUE UNIQUEMENT À L’UTILISATEUR FINAL. ELLE EST LA SEULE
GARANTIE APPLICABLE À NOS PRODUITS. ELLE EXCLUT TOUTE AUTRE GARANTIE EXPRESSE OU IMPLICITE.
CAPITAL SAFETY EXCLUT EXPLICITEMENT ET DÉCLINE TOUTE GARANTIE IMPLICITE DE MISE EN MARCHÉ ET
D’ADAPTATION À DES FINS PARTICULIÈRES, ET NE SERA RESPONSABLE POUR AUCUN DOMMAGE-INTÉRÊT
DIRECT OU INDIRECT, CORRÉLATIF OU ACCESSOIRE DE TOUTE NATURE Y COMPRIS ET DE MANIÈRE NON
LIMITATIVE, LES PERTES DE PROFITS, LES REVENUS OU LA PRODUCTIVITÉ, LES BLESSURES CORPORELLES,
VOIRE LA MORT OU DOMMAGES À LA PROPRIÉTÉ, DANS LE CADRE DE TOUTE THÉORIE DE RESPONSABILITÉ, Y
COMPRIS ET DE MANIÈRE NON LIMITATIVE UN CONTRAT, UNE GARANTIE, UNE RESPONSABILITÉ (Y COMPRIS LA
NÉGLIGENCE) OU TOUTE AUTRE THÉORIE LÉGALE OU ÉQUITABLE.
GARANTÍA LIMITADA DE POR VIDA
Garantía para el usuario fi nal: D B Industries, Inc., que opera bajo el nombre de CAPITAL SAFETY USA
(“CAPITAL SAFETY”) garantiza al usuario fi nal original (“Usuario fi nal”) que sus productos están libres de defectos
de materiales y de mano de obra en condiciones normales de uso y mantenimiento. Esta garantía se extiende
durante la vida útil del producto a partir de la fecha en que el Usuario fi nal adquiere el producto, nuevo y sin
uso, a un distribuidor autorizado de CAPITAL SAFETY. La entera responsabilidad de CAPITAL SAFETY hacia el
Usuario fi nal y el remedio exclusivo para el Usuario fi nal bajo esta garantía están limitados a la reparación o el
reemplazo por materiales de todo producto defectuoso dentro de su vida útil (según CAPITAL SAFETY lo determine
y considere apropiado a su solo criterio). Ninguna información o asesoramiento, oral o escrito, proporcionado
por CAPITAL SAFETY, sus distribuidores, directores, funcionarios, agentes o empleados creará una garantía
diferente o adicional ni aumentará de ninguna manera el alcance de esta garantía. CAPITAL SAFETY no aceptará
responsabilidad por defectos resultantes del abuso, el uso incorrecto, la alteración o la modifi cación del producto,
ni por defectos resultantes de no respetar las instrucciones del fabricante durante la instalación, el mantenimiento
o el uso del producto.
LA GARANTÍA DE CAPITAL SAFETY SE APLICA ÚNICAMENTE AL USUARIO FINAL. ESTA GARANTÍA ES LA
ÚNICA GARANTÍA QUE SE APLICA A NUESTROS PRODUCTOS Y REEMPLAZA A TODAS LAS OTRAS GARANTÍAS
Y RESPONSABILIDADES, EXPRESAS O IMPLÍCITAS. CAPITAL SAFETY EXPRESAMENTE EXCLUYE Y RENUNCIA A
TODAS LAS GARANTÍAS IMPLÍCITAS DE COMERCIABILIDAD O APTITUD PARA UN PROPÓSITO PARTICULAR, Y
NO SERÁ RESPONSABLE POR DAÑOS INCIDENTALES, PUNITIVOS O EMERGENTES DE NINGUNA NATURALEZA,
INCLUYENDO SIN LIMITACIÓN PÉRDIDAS DE INGRESOS, GANANCIAS O PRODUCTIVIDAD; NI POR
LESIONES CORPORALES O MUERTE, O PÉRDIDA DE O DAÑO A LA PROPIEDAD, BAJO CUALQUIER TEORÍA DE
RESPONSABILIDAD, INCLUYENDO SIN LIMITACIÓN CONTRATO, GARANTÍA, RESPONSABILIDAD ESTRICTA,
AGRAVIO (INCLUIDA NEGLIGENCIA) O CUALQUIER OTRA TEORÍA LEGAL O EQUITATIVA.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

3M PROTECTA® Self Retracting Lifeline - Web 3100433, Red, 20 ft. (6.1 m), 1 EA Mode d'emploi

3M
Marque
3M
Modèle
PROTECTA® Self Retracting Lifeline - Web 3100433, Red, 20 ft. (6.1 m), 1 EA
Taper
Mode d'emploi
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents