3M 3102003 Manuel utilisateur

Marque: 3M

Modèle: 3102003

Taper: Manuel utilisateur

USER INSTRUCTION MANUAL

100% TIE-OFF TALON™ SELF RETRACTING LIFELINES

This manual is intended to meet the Manufacturer’s Instructions as

required by ANSI Z359.14, CSA Z259.2.2 (Type 1), and should be used

as part of an employee training program as required by OSHA.

Instructions for the following series products:

100% Tie-off SRL

Model Numbers: (see inside back cover)

Form: 5902332 Rev:G

The Ultimate in Fall Protection

Figure 1 - 100% Tie -off Talon Self Retracting Lifeline

WARNING: This product is part of a personal fall arrest system. The

user must read and follow the manufacturer’s instructions for each

component of the system. These instructions must be provided to

the user of this product. The user must read and understand these

instructions before using this product. Manufacturer’s instructions must

be followed for proper use and maintenance of this product. Alteration

or misuse of this product, or failure to follow instructions may result in

serious injury or death.

IMPORTANT: If you have questions about the use, care, or suitability

of this equipment for your application contact DBI‑SALA.

IMPORTANT: Before using this equipment record the product

identication information from the ID label in the inspection and

maintenance log in section 9.0 of this manual.

Lanyard

Keepers

Delta

Comfort

Pad

6 ft. Lifelines

100% Tie-off

Talon SRL

Quick-connect

attachment

handle

SAFETY INFORMATION

Please read, understand, and follow all safety information contained in these

instructions prior to the use of this Self-Retracting Device (SRD). FAILURE TO DO

SO COULD RESULT IN SERIOUS INJURY OR DEATH.

These instructions must be provided to the user of this equipment. Retain these

instructions for future reference.

INTENDED USE:

This Self-Retracting Device is intended for use as part of a complete personal fall protection

system.

Use in any other application including, but not limited to, material handling, recreational

or sports related activities, or other activities not described in the User Instructions, is not

approved by 3M and could result in serious injury or death.

This device is only to be used by trained users in workplace applications.

! WARNING

This Self-Retracting Device is part of a personal fall protection system. It is expected that all

users be fully trained in the safe installation and operation of their personal fall protection

system. Misuse of this device could result in serious injury or death. For proper

selection, operation, installation, maintenance, and service, refer to these User Instructions

including all manufacturer recommendations, see your supervisor, or contact 3M Technical

Services.

• To reduce the risks associated with working with an SRD which, if not avoided,

could result in serious injury or death:

- Before each use, inspect the SRD and check for proper locking and retraction.

- If inspection reveals an unsafe or defective condition, remove the device from

service and repair or replace according to the User Instructions.

- If the SRD has been subjected to fall arrest or impact force, immediately remove the

SRD from service and label the device ‘UNUSABLE’.

- Ensure the lifeline is kept free from any and all obstructions including, but not limited

to; entanglement with moving machinery or equipment (e.g., the top drive of oil

rigs), other workers, yourself, surrounding objects, or impact from overhead objects

that could fall onto the lifeline or the worker.

- Never allow slack in the lifeline. Do not tie or knot the lifeline.

- Attach the unused leg(s) of the Harness Mounted SRD to the parking attachment(s)

of the harness if equipped.

- Do not use in applications that have an obstructed fall path. Working on slowly

shifting material, such as sand or grain, or within conned or cramped spaces, may

not allow the worker to reach sufcient speed to cause the SRD to lock. A clear path

is required to assure positive locking of the SRD.

- Avoid sudden or quick movements during normal work operation. This may cause

the device to lock up.

- Ensure that fall protection systems/subsystems assembled from components made

by different manufacturers are compatible and meet the requirements of applicable

standards, including the ANSI Z359 or other applicable fall protection codes,

standards, or requirements. Always consult a Competent and/or Qualied Person

before using these systems.

• To reduce the risks associated with working at height which, if not avoided,

could result in serious injury or death:

- Ensure your health and physical condition allow you to safely withstand all of the

forces associated with working at height. Consult with your doctor if you have any

questions regarding your ability to use this equipment.

- Never exceed allowable capacity of your fall protection equipment.

- Never exceed maximum free fall distance of your fall protection equipment.

- Do not use any fall protection equipment that fails pre-use or other scheduled

SIT 5908239 Rev. C

inspections, or if you have concerns about the use or suitability of the equipment for

your application. Contact 3M Technical Services with any questions.

- Some subsystem and component combinations may interfere with the operation

of this equipment. Only use compatible connections. Consult 3M prior to using

this equipment in combination with components or subsystems other than those

described in the User Instructions.

- Use extra precautions when working around moving machinery (e.g. top drive of oil

rigs) electrical hazards, extreme temperatures, chemical hazards, explosive or toxic

gases, sharp edges, or below overhead materials that could fall onto you or your fall

protection equipment.

- Use Arc Flash or Hot Works devices when working in high heat environments.

- Avoid surfaces and objects that can damage the user or equipment.

- Ensure there is adequate fall clearance when working at height.

- Never modify or alter your fall protection equipment. Only 3M or parties authorized

in writing by 3M may make repairs to the equipment.

- Prior to use of fall protection equipment, ensure a rescue plan is in place which

allows for prompt rescue if a fall incident occurs.

- If a fall incident occurs, immediately seek medical attention for the worker who has

fallen.

- Do not use a body belt for fall arrest applications. Use only a Full Body Harness.

- Minimize swing falls by working as directly below the anchorage point as possible.

- If training with this device, a secondary fall protection system must be utilized in a

manner that does not expose the trainee to an unintended fall hazard.

- Always wear appropriate personal protective equipment when installing, using, or

inspecting the device/system.

DESCRIPTIONS

Talon 100% Tie-off Series Self Retracting Lifeline: See Figure 1. Includes quick

connect attachment handle, 6 foot nylon web lifeline, Delta™ comfort pad, and

two lanyard keepers.

1.0 APPLICATIONS

1.1 PURPOSE: DBI-SALA self retracting lifelines (SRL’s) are components of

a personal fall arrest system (PFAS). These SRL’s may be used to provide

continuous fall protection while ascending, descending, or moving laterally.

FALL PROTECTION: The SRL is used as part of a complete personal fall

arrest system. Personal fall arrest systems typically include a full body

harness, anchorage connector, and SRL.

1.2 LIMITATIONS:

A. PERSONAL FALL ARREST SYSTEM: Personal fall arrest system

components used with the SRL must meet the system requirements

specified in sections 2.1 and 2.2.

B. ANCHORAGE STRUCTURE: The structure to which the SRL is

attached must be selected according to the limitations and strength

requirements specified in this manual. See section 2.4 for more

information.

C. FALL CLEARANCE: There must be sufficient clearance below the user

to arrest a fall before the user strikes the ground or other obstruction.

Refer to section 3.2 for more information.

D. CAPACITY: The SRL is designed for use by persons with a combined

weight (clothing, tools) of no more than 310 lbs or 420 lbs. No more

than one person may be connected to the SRL at any time.

3102014, 3102015, 3102016, 3102017: 420 lbs

All Other Models: 310 lbs

E. LOCKING SPEED: Use of the SRL in confined spaces, on slowly

shifting material (sand or grain), or on a low pitched roof may not

allow sufficient lock-up speed to arrest a fall. A clear fall path is

required to safely arrest a fall.

F. NORMAL OPERATION: Normal operation will allow the full length

of the lifeline to extend and retract without hesitation or creating a

slack line condition as the worker moves at normal speeds. If a fall

occurs, a speed sensing brake system will activate, stopping the fall

and absorbing much of the energy created. If a fall has been arrested,

the SRL must be removed from service and inspected. See section 5.0.

Sudden or quick movements should be avoided during normal work

operation as this may cause the SRL to lock-up.

G. ENVIRONMENTAL HAZARDS: Use of the SRL in hazardous

environments may require additional precautions to reduce the

possibility of injury to the user or damage to the personal fall arrest

system. Hazards may include, but are not limited to; heat, caustic or

corrosive chemicals, high voltage power lines, explosive or toxic gases,

moving machinery, sharp edges, overhead objects that my fall and

strike the lifeline.

H. TRAINING: The SRL is intended to be installed and used by persons

trained in its application and use. See section 4.

1.3 Refer to national standards, including ANSI Z359.14 and applicable local,

state, and federal (OSHA) requirements governing this equipment for more

information on this equipment and associated system components.

2.0 SYSTEM REQUIREMENTS

2.1 COMPATIBILITY OF COMPONENTS: DBI-SALA equipment is designed

for use with DBI-SALA approved components and subsystems only.

Substitutions or replacements made with non-approved components or

subsystems may jeopardize compatibility of equipment and may effect the

safety and reliability of the complete system. Personal fall arrest systems

must meet applicable local, state, and federal (OSHA) requirements. A full

body harness must be used with the Talon SRL.

2.2 COMPATIBILITY OF CONNECTORS: Connectors are considered to be

compatible with connecting elements when they have been designed to

work together in such a way that their sizes and shapes do not cause their

gate mechanisms to inadvertently open regardless of how they become

oriented. Contact DBI-SALA if you have any questions about compatibility.

Connectors (hooks, carabiners, and D-rings) must be capable of supporting

at least 5,000 lbs. (22.2kN). Per ANSI Z359.14, connector gates must

be able to withstand a load of 3,600 lbs (16 kN): the face of the gate

must withstand 3,600 lbs (16 kN); the side of the gate must withstand

3,600 lbs (16 kN), and the minor axis for a snap hook or carabiner must

withstand 3,600 lbs (16 kN), except those with captive eyes. Connectors

must be compatible with the anchorage or other system components. Do

not use equipment that is not compatible. Non-compatible connectors may

unintentionally disengage. See Figure 2. Connectors must be compatible

in size, shape, and strength. Self locking snap hooks and carabiners are

required by ANSI Z359.14 and OSHA.

2.3 MAKING CONNECTIONS: Only use self-locking snap hooks and

carabiners with this equipment. Only use connectors that are suitable to

each application. Ensure all connections are compatible in size, shape

and strength. Do not use equipment that is not compatible. Ensure all

connectors are fully closed and locked.

DBI-SALA connectors (snap hooks and carabiners) are designed to be used

only as specied in each product’s user’s instructions. See Figure 3 for

inappropriate connections. DBI-SALA snap hooks and carabiners should not

be connected:

A. To a D-ring to which another connector is attached.

B. In a manner that would result in a load on the gate.

NOTE: Large throat opening snap hooks should not be connected

to standard size D‑rings or similar objects which will result in a load

on the gate if the hook or D‑ring twists or rotates. Large throat snap

hooks are designed for use on xed structural elements such as rebar

or cross members that are not shaped in a way that can capture the

gate of the hook.

C. In a false engagement, where features that protrude from the snap

hook or carabiner catch on the anchor and without visual confirmation

seems to be fully engaged to the anchor point.

D. To each other.

E. Directly to webbing or rope lanyard or tie-back (unless the

manufacturer’s instructions for both the lanyard and connector

specifically allow such a connection).

F. To any object which is shaped or dimensioned such that the snap hook

or carabiner will not close and lock, or that roll-out could occur.

G. In a manner that does not allow the connector to align with the fall

arrest device (i.e., SRL) while under load.

2.4 ANCHORAGE STRUCTURE: The anchorage to which the SRL is attached

must be capable of sustaining static loads in the directions applied by the

personal fall arrest system of at least 3,600 lbs. with certication of a

qualied person, or 5,000 lbs. without certication. See ANSI Z359.14 for

certication requirements. When more than one personal fall arrest system

is attached to the same structure, the strength requirements stated above

must be multiplied by the number of personal fall arrest systems attached

to the structure.

•

From OSHA 1910.104 and 1926.502: Anchorages used for

attachment of a personal fall arrest system shall be independent

of any anchorage being used to support or suspend platforms, and

must support at least 5,000 lbs. per user attached, or be designed,

installed, and used as part of a complete personal fall arrest system

which maintains a safety factor of at least two, and is supervised by a

qualied person.

2.5 USING THE SRL WITH A HORIZONTAL SYSTEM: The SRL and

horizontal system components must be compatible. Horizontal systems

must be designed and installed under the supervision of a qualied person.

Figure 2 - Unintentional Disengagement (Roll-out)

If the connecting element that a snap hook (shown) or carabiner attaches to is

undersized or irregular in shape, a situation could occur where the connecting

element applies a force to the gate of the snap hook or carabiner. This force may

cause the gate (of either a self-locking or a non-locking snap hook) to open,

allowing the snap hook or carabiner to disengage from the connecting point.

1. Force is applied to

the snap hook.

2. The gate presses against

the connecting ring.

3. The gate opens

allowing the snap

hook to slip off.

Small ring or other

non-compatibly

shaped element

3.0 INSTALLATION AND USE

WARNING: Do not alter or intentionally misuse this equipment. Consult

DBI‑SALA when using this equipment in combination with components or

subsystems other than those described in this manual. Some subsystem

and component combinations may interfere with the operation of this

equipment. Use caution when using this equipment around moving

machinery, electrical hazards, chemical hazards, and sharp edges; or

under overhead materials that may fall onto the lifeline. Failure to heed

this warning may result in equipment malfunction, injury, or death.

WARNING: Consult your doctor if there is reason to doubt your tness to

safely absorb the shock from a fall arrest. Age and tness can seriously affect

your ability to withstand a fall. Pregnant women and minors must not use this

equipment.

3.1 BEFORE EACH USE: Inspect the SRL according to section 5.0.

3.2 PLAN your personal fall arrest system before installing and using this

equipment. Consider all factors affecting your safety during use of this

equipment.

A. ANCHORAGE: Select a rigid anchorage point capable of supporting at

least 5,000 lbs. See section 2.4. Select an anchorage location that will

avoid free fall and swing fall hazards. To prevent an increased free fall

distance do not work above the anchorage.

B. FREE FALL: Your personal fall arrest system must be rigged such

that an anchor point is above your harness attachment element

(dorsal D-ring) when in use. Avoid working where your lifeline may

cross or tangle with that of another worker. Do not allow the lifeline

to pass under your arms or between your feet. Never clamp, knot, or

otherwise prevent the lifeline from retracting. Do not allow slack in

your lifeline. Do not lengthen the SRL by connecting a lanyard or other

component.

Figure 3 - Inappropriate Connections

C. SWING FALLS: Swing falls occur when the anchorage point is not

directly above the point where a fall occurs. See Figure 4. The force

of striking an object in a swing fall may cause serious injury. In a

swing fall, the total vertical fall distance will be greater than if the

user had fallen directly below the anchorage point, thus increasing

the total free fall distance and the area required to safely arrest the

user. The SRL will activate regardless of its orientation relative to the

user. Minimize swing falls by working as directly below the anchorage

point as possible. Never permit a swing fall if injury could occur. If a

swing fall situation exists in your application contact DBI-SALA before

proceeding.

D. FALL CLEARANCE: Ensure adequate clearance exists in your fall path

to prevent striking an object. A minimum of 6 feet from the working

level to the lower level or nearest obstruction is recommended. See

Figure 4.

E. SHARP EDGES:

Avoid working where the lifeline will be in contact with

or abrade against unprotected sharp edges. Provide protection for the

lifeline when possible. An energy absorbing component can sometimes

be added in-line to further protect the worker. Compatibility and total

fall distance must be considered if this is done. Contact DBI-SALA before

using an in-line energy absorbing component or lanyard with an SRL.

F. AFTER A FALL: Equipment

which has been subjected

to fall arrest forces must be

removed from service for

inspection. See section 5.0.

G. RESCUE: If a fall occurs,

the employer must have a

rescue plan and the ability to

implement a rescue.

3.3 ATTACHING THE DELTA

COMFORT PADS TO A FULL

BODY HARNESS: Lay the

harness on a work surface with

the dorsal

D-ring facing up. Slide

the Comfort Pad underneath the

webbing with the longer arms

going up underneath the shoulder

straps and the shorter arms

extending downward toward the

leg straps. Open the hook-and-

loop fastening of each arm of the

pad and tuck the harness webbing

between the folds of the pad, then

reseal the hook and loop fastening

and close the snaps. See Figure 5.

NOTE: The Comfort Pads

are optional and are not

necessary to the use of

the 100% Tie‑off SRL

Figure 4 - Swing Falls

NOTE: The 6 ft. minimum assumes the

fall occurs from a standing position

and the anchor is located overhead.

If the worker is kneeling or crouching

near an edge when a fall occurs, and

additional 3 ft. clearance is needed.

If the worker is not directly below the

anchor, additional clearance is needed.

Working

Level

Lower

Level

6 Ft. Minimum

Swing Fall

Hazard

3.4 ATTACHING THE SRL TO A FULL BODY HARNESS: See Figure 6.

Step 1. Open the Quick-Connect Handle:, Depress the Locking Lever

(A) and then pull the Locking Pin (B) out to release the Handle.

Once released, swing the Handle open.

Step 2. Insert the Quick-Connect Handle under the Harness

Webbing: Insert the Handle (C) under the two Web Straps

(D) that pass through the base of the Dorsal D-Ring at a point

adjacent to the base of the D-Ring. Slide the Handle under both

Web Straps until it extends out the opposite side of the straps.

IMPORTANT: The handle of the SRL must pass

underneath the web in the same manner as the

existing D-ring. See Figure 7.

Step 3. Close the Quick-Connect Handle: Swing the Handle (C) closed

and align the hole in Handle with the end of the Locking Pin (B).

Release the Locking Lever (A) so the Locking Pin springs closed into

the hole in the Handle.

WARNING: Ensure the locking pin fully engages the

handle and the locking lever is in the locked position.

Step 4. Secure Twin-Leg Talon SRLs with the Hook and Loop

Straps: Wrap the Hook and Loop Straps (E) extending from the

sides of the Twin-Leg Talon underneath the Harness Shoulder

Straps and fasten them together to hold the SRL in the proper

position.

3.5 USING THE 100% TIE-OFF SRL: When connected to the SRL the

worker is free to move about within the recommended working area. The

lifeline should extend

and retract without

hesitation or creating

a slack line condition

as the worker moves

at normal speeds. If a

fall occurs the SRL will

lock and arrest the fall.

When disconnecting

from the SRL keep the

lifeline under control as

it recoils back into the

device.

100% TIE-OFF SRL

CONSIDERATIONS:

Commonly known as

100% tie-off, “Y” type,

twin leg SRL, these

energy absorbing

devices can be used

to provide continuous

fall protection while

ascending, descending,

or moving laterally. With

one leg attached to

Figure 5 - Installaing Pads

Hook and

Loop Flaps

Snaps

To install the pads, lay out the harness as

shown and place the pads under the straps

then wrap the hook and loop flaps over the

straps and close the snaps.

the anchor structure, the worker can move to a new location, attach the

second unused leg, and disconnect original attached leg. This procedure is

repeated until the work location is reached. Other practices that must be

followed in order to use a 100% tie-off type SRL safely include:

• Connection of both lanyard legs to separate anchorage points is

acceptable See Figure 8.

• Never connect more than one person to a “Y” type SRL at a time. See

Figure 9.

• Do not allow the lifelines to become tangled or twisted together as this

may prevent them from retracting.

• Do not allow any lanyard to pass under arms or between legs during

use.

Figure 6 - Using the Attachment Handle

Figure 7 Figure 8 Figure 9

NO!

3.6 LANYARD KEEPERS: Two lanyard

keepers are supplied with the 100%

Tie-off SRL. One of these lanyard

keepers should be attached to

attached to each shoulder strap. Pull

open the hook and loop attachment

straps and wrap the straps around

the shoulder strap at a convenient

location, then close the hook and

loop attachments. While the lifelines

are not in use they should be

attached to the lanyard keepers to

keep them secured in a convenient

location. See Figure 10.

3.7 IMPACT INDICATOR: See Figure

11. The SRL incorporates an impact indicator in the lifeline. The lifeline web

is folded over and stitched with red thread. The stitched fold will pull out at

approximately 450 lbs. If the red stitching is intact the SRL has not been

impacted. If the red stitching is broken and the fold torn apart, the SRL has

been impacted and must

be removed from service

and returned to an

authorized service center

for repair.

4.0 TRAINING

4.1 It is the responsibility

of all users of this

equipment to understand

these instructions, and

to be trained in the

correct installation,

use, and maintenance

of this equipment.

These individuals

must be aware of

the consequences of

improper installation or use of this equipment. This user manual is not a

substitute for a comprehensive training program. Training must be provided

on a periodic basis to ensure prociency of the users.

WARNING: Training must be conducted without exposing the trainee to a fall

hazard. Training must be repeated on a periodic basis.

5.0 INSPECTION

5.1 FREQUENCY:

• Before Each Use:

OSHA 1910.104, OSHA 1926.502 and ANSI

Z359.14 requires an inspection of equipment before each use. See

sections 5.2, 5.3, and 5.4 for inspection guidelines.

• Annually:

ANSI Z359.14 requires a formal inspection of the SRL be

completed by a competent person other than the user. More frequent

Figure 11 - Impact Indicator

Before Impact

Impact Indicator fold

is present

After Impact

Impact Indicator fold

is missing

Figure 10 - Lanyard Keepers

Unused lifeline should be

attached to the lanyard

keeper on the shoulder

strap.

inspections by a competent person may be required based on the

nature and severity of workplace conditions affecting the equipment

and the modes of use and exposure time of the equipment. See

sections 5.2, 5.3, and 5.4 for inspection guidelines. Record results in

the inspection and maintenance log in section 9.0.

• After a Fall Arrest:

Inspect impact indicator according to section 5.2,

and the entire SRL according to sections 5.3 and 5.4.

5.2 IMPACT INDICATOR: To inspect the impact indicator, nd the fold in the

lifeline stitched with red thread, as shown in Figure 10. If the red stitching

is broken and the fold torn apart, the SRL has been impacted and must

be removed from service and returned to an authorized service center for

repair. Do not restitch the fold.

WARNING: If the SRL has been subjected to fall arrest or impact forces it

must be removed from service and returned to an authorized service center for

repair.

5.3 INSPECTION STEPS:

Step 1. Check for loose screws and bent or damaged parts.

Step 2.

Check the housing for distortion, cracks, or other damage. Ensure

the anchorage point is not damaged or distorted.

Step 3. The lifeline must fully extend and retract smoothly with no

hesitation or slack line condition.

Step 4. Ensure the device locks when the lifeline is pulled sharply.

Lock-up should be positive, with no slipping.

Step 5. All labels must be present and fully legible. See section 8.0.

Step 6. Check for corrosion on the entire unit.

Step 7. Check the lifeline for cuts, burns, chemical damage, or severely

abraded areas. The lifeline must not be damaged.

Step 8. Inspect the Quick-Connect Handle and Locking Lever for

damage and proper operation (see Figure 12). Make sure the

Locking Pin (A) closes and locks in closed position when the

Locking Lever (B) is released. Make sure the Locking Lever is

held in position by the Plastic Nubs (C) on the SRL Housing

Halves.

Step 9. Check the connecting hooks or carabiners for damage,

distortion, or corrosion, and working condition.

Step 10. Inspect each component of the personal fall arrest system

according to manufacturer’s instructions.

Step 11. Record the inspection results in the inspection and maintenance

Figure 12 - Quick-Connect Handle Inspection

5.4 If the inspection reveals an unsafe or defective condition, remove the SRL

from service and contact an authorized service center for repair.

NOTE: Only DBI‑SALA or parties authorized in writing may make

repairs to this equipment.

6.0 MAINTENANCE, SERVICING, AND STORAGE

6.1 MAINTENANCE:

A. HOUSING: Periodically clean the exterior of the SRL with water and a

mild detergent. Position the SRL so water can drain out. Clean labels

as required.

B. LIFELINE: Clean the lifeline with water and a mild detergent. Rinse

and thoroughly air dry. Do not force dry with heat. An excessive build-

up of dirt or other contaminants may prevent the lifeline from fully

retracting, causing a potential free fall hazard. Return the SRL to an

authorized service center for lifeline replacement if necessary.

C. PERSONAL FALL ARREST SYSTEM COMPONENTS: Clean and

store associated system components according to manufacturer’s

instructions.

6.2 SERVICING: Do not disassemble the SRL. Do not lubricate any part of

the SRL. Additional maintenance and servicing must be performed by an

authorized service center. A return authorization number must be issued by

DBI-SALA. See section 5.1 for servicing frequency.

6.3 STORAGE: Store the SRL in a cool, dry, and clean environment, out of

direct sunlight. Avoid storing the SRL in areas where chemical vapors exist.

Thoroughly inspect the SRL after extended storage.

7.0 SPECIFICATIONS

7.1 PERFORMANCE SPECIFICATIONS:

• Capacity: One User Only;

3102014, 3102015, 3102016, 3102017: 75 lbs - 420 lbs

All Other Models: 75 lbs - 310 lbs

• Working Range: 2.5 ft. to 6 feet

• Maximum Arresting Force: When tested in accordance with ANSI

3102014, 3102015,

3102016, 3102017:

310 lbs - 420 lbs 1,350 lbs

All Other Models: 75 lbs - 310 lbs 1,350 lbs

• Average Locking Speed: 4.5 ft./second

• Maximum Arresting Distance: 42 inches

7.2 PHYSICAL SPECIFICATIONS:

• Overall Dimensions, Quick-Connect Attachment Handle

Models (LxWxH): 7.5 x 3.8 x 2.6 inches

• Materials:

Housing: Nylon Plastic

Cable Drum: Glass lled nylon

Internal Components: Heat-treated Alloy Steel and Stainless Steel

Lifeline: 1 inch nylon web

Anchorage Handle: Steel, locking type, quick-connect

Hooks: 5,000 lb. minimum tensile strength

• Weight: 5.4 lbs. (3102000 model)

7.3 PATENTS AND REQUIREMENTS:

• Patents: Pending

• Meets: Z359.14 Class B, OSHA 1926.502, and OSHA 1910.140

requirements.

8.0 LABELING

8.1 THE FOLLOWING LABELS MUST BE PRESENT AND FULLY LEGIBLE:

Warning & Use Label

i-Safe Label

i-Safe RFID Tag

IMPORTANT: The

i-Safe Identication

Number on the RFID

Tag is for purposes

of electronic record

keeping with the

i‑Safe system.

Where the Serial

Number is printed

on the product’s ID

Label (illustrated

above), the i‑Safe

Identication Number

and Serial Number

may be different

numbers.

9.0 INSPECTION AND MAINTENANCE LOG

SERIAL NUMBER: __________________________________________

MODEL NUMBER: ___________________________________________

DATE PURCHASED: ______________DATE FIRST USED: __________

INSPECTION

DATE

INSPECTION

ITEMS NOTED

CORRECTIVE

ACTION

MAINTENANCE

PERFORMED

Approved By:

MODEL NUMBERS

This instruction applies to the following Models:

3101998

3101999

3102000

3102001

3102002

3102003

3102004

3102005

3102006

3102007

3102008

3102009

3102014

3102015

3102016

3102017

3102019

3102020

3102100

3102101

3102102

3102115

Additional Model Numbers may appear on the next printing of these instructions.

MANUEL D’INSTRUCTIONS POUR L’UTILISATEUR

CORDE D’ASSURANCE AUTO-RÉTRACTABLE AVEC

ARRIMAGE À 100% TALON™

Ce manuel correspond les instructions du fabricant tel que requis par

ANSI Z359.14, CSA Z259.2.2 (Type 1), et doit être utilisé comme une

partie du programme de formation de l’employé conformément à la

réglementation OSHA.

Les instructions des produits de la série suivante:

Corde d’assurance auto-rétractable

avec arrimage à 100%

Numéro de produit : (voir à l’intérieur de la couverture.)

Formulaire : 5902332 Rév : G

The Ultimate in Fall Protection

La page charge ...

3M 3102003 Manuel utilisateur

Marque: 3M

Modèle: 3102003

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: 3M 3102003 User manual

3M 3102003 Manuel utilisateur

3M 3102003 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents