Chief Manufacturing Indoor Furnishings JWP Manuel utilisateur

Catégorie
Mur
Taper
Manuel utilisateur

Ce manuel convient également à

INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
JWP
JWD
JWS
Medium Flat Panel Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
J-Series
J-Series Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, Inc., and its affiliated corporations
and subsidiaries, intend to make this manual accurate and
complete. However, Milestone makes no claim that the
information contained herein covers all details, conditions or
variations, nor does it provide for every possible contingency in
connection with the installation or use of this product. The
information contained in this document is subject to change
without notice or obligation of any kind. Milestone makes no
representation of warranty, expressed or implied, regarding the
information contained herein. Milestone assumes no
responsibility for accuracy, completeness or sufficiency of the
information contained in this document.
Chief® and Centris™ are registered trademarks of Milestone
AV Technologies. All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the J-Series mount up to
(and including) the display does not exceed 75 lbs (34 kg).
DIMENSIONS
5.29
134.32
3.94
100
3.94
100
6.00
152.40
3.35
85.07
8.32
211.43
6.92
175.87
2.31
58.57
4.75
120.65
3.22
81.77
JWP
Installation Instructions J-Series
3
DIMENSIONS
8.48
215.36
3.94
100
3.94
100
6.00
152.40
11.85
300.97
11.51
292.47
6.92
175.87
5.50
139.62
4.75
120.65
3.22
81.77
3.16
80.36
13.11
332.93
JWS
20.35
516.87
8.50
215.90
8.50
215.90
6.00
152.40
3.22
81.77
14.70
373.33
3.94
100
3.94
100
1.03
26.20
2.69
68.25
12.11
307.72
9.11
231.52
8.69
220.66
4.75
120.65
JWD
Installation Instructions J-Series
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
J-Series Installation Instructions
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
Table 1: Parts
QUANTITY By
MODEL
ITEM DESCRIPTION JWP JWS JWD
A PIVOT PITCH WALL MOUNT 1 - -
B SINGLE ARM WALL MOUNT - 1 -
C DUAL ARM WALL MOUNT - - 1
D J-SERIES WALL PLATE 1 1 1
E CABLE MANAGEMENT COVER - 1 2
F HEX HEAD LAG SCREW, 3/8" X 3" 2 2 2
G PHILLIPS FLAT MACHINE SCREW, 8-32 X 3/8" - 2 4
1/8"
#2
A
B
C
D
E
F
G
Interface
Bracket
Kit
(Including Hardware)
x 1
x1
I/M
J-Series Installation Instructions
6
INSTALLATION
WARNING: FAILURE TO PROVIDE ADEQUATE
STRUCTURAL STRENGTH FOR THIS MOUNT CAN
RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE
TO EQUIPMENT! It is the installer’s responsibility to make
sure the structure to which this mount is attached can support
five times the combined weight of the mount and all
equipment attached to it. Reinforce the structure as required
before installing the mount.
1. Determine location for mount keeping in mind display size,
extension, height adjustment (if applicable), and pitch/roll
requirements.
NOTE: Wall plate (D) MUST be installed into wood stud.
2. Using wall plate (D) as a template, mark then drill two 1/8"
diameter pilot holes through top and bottom holes of wall
bracket into wall structure. (See Figure 1)
Figure 1
3. Install two 3/8" x 3" hex head lag screws (F) through wall
plate (D) and drywall into wood stud. (See Figure 1)
4. Ensure wall plate (D) is vertical, then tighten screws (D).
CAUTION: Overtightening screws may cause wall bracket
to compress into soft wall surface, resulting in difficult mount
installation or improper engaging of set screw in later step.
5. Insert top of wall mount (A, B or C) over lip on top of wall
plate (D). (See Figure 2)
6. Swing wall mount down flush against wall.
Figure 2
7. Tighten set screw in bottom of wall mount. (See Figure 3)
NOTE: Ensure set screw engages on back side of wall plate to
properly secure wall mount.
Figure 3
2
3
(F) x 2
(A, B or C)
(D)
5
6
(A, B or C)
(D)
7
Set
Screw
Installation Instructions J-Series
7
DISPLAY INSTALLATION
1. Determine mounting pattern on display.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY AND DAMAGE TO EQUIPMENT! DO NOT
substitute hardware. Use only hardware supplied by
manufacturer!
WARNING: IMPROPER INSTALLATION CAN LEAD TO
ELECTRIC SHOCK OR DAMAGE TO EQUIPMENT! Screw
length must not exceed the depth of threaded mounting insert
in display.
WARNING: OVERTIGHTENING OF SCREWS CAN
DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL
INJURY AND DAMAGE TO EQUIPMENT! DO NOT over
tighten screws when installing interface bracket.
NOTE: If the display being installed has a 100x100 VESA
mounting pattern, no interface bracket is required and
the display can be mounted directly to the mounting
plate as outlined below.
NOTE: If the display being installed requires an interface
bracket, refer to the interface bracket installation
instructions.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display! Proper screws will
easily and completely thread into display mounting holes.
Ensure that screws are not too long.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread
engagement in display may cause display to fall! Back out
screws ONLY as necessary to allow installation of mounting
plate!
1. Start two M4 x 8mm Phillips pan head screws (included in
hardware kit) into upper mounting holes in display back.
(See Figure 4)
NOTE: Leave at least 1/8" of each screw protruding out back
of display.
Figure 4
2. Align two screws in display back with upper teardrop
mounting holes in mounting plate and lower display until
screws are seated in lower area of teardrop mounting holes.
(See Figure 5)
Figure 5
3. Install two more of the same screws through lower mounting
holes in display mounting plate and into display back.
(See Figure 6)
1
x2
2
2
(A, B or C)
J-Series Installation Instructions
8
Figure 6
4. Tighten all hardware.
CABLE MANAGEMENT
1. Attach all cables to display.
CAUTION: Ensure that adequate cable slack exists for
movement of display, and that cables will not be pinched by
installation of cable management cover(s) (E) or screws (G).
2. Carefully insert cables in cavity located in lower portion of
mount arm (See Figure 7).
3. Install cover (E) with two 8-32 x 3/8" Phillips screws (G).
(See Figure 7)
Figure 7
ADJUSTMENTS
Swing Arm
PIVOT / SWING TENSION
1. Slightly loosen or tighten the adjustment screw(s) as
necessary (See Figure 8).
Figure 8
DISPLAY ROLL / PITCH / YAW TENSION:
1. Disconnect all wires and cable from the display.
2. Remove two Lower screws securing display to Centris cup.
3. Loosen two Upper screws securing display.
4. Lift display upward and away from mount.
5. Turn the tension adjustment screw clockwise to increase
tension, or counter-clockwise to decrease tension.
(See Figure 9)
Figure 9
Re-install display.
3
x 2
2
(G) x 2 (JWS)
Cable Path
(typical)
(E) x 1 (JWS)
3
(G) x 4 (JWD)
(E) x 2 (JWD)
1
5
Installation Instructions J-Series
9
J-Series Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
F 877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620
F +31 (0)40 2668615
Asia Pacific A Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
P +86-755-8996 9226
F +86-755-8996 9217
Chief Manufacturing, a division of
Milestone AV Technologies
8832-000253
2008 Milestone AV Technologies
www.chiefmfg.com
06/08
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Chief Manufacturing Indoor Furnishings JWP Manuel utilisateur

Catégorie
Mur
Taper
Manuel utilisateur
Ce manuel convient également à