Indesit XWDE 861480X W EU Mode d'emploi

1

GB

Washer-dryer

Instructions for use

! This symbol reminds you to read this instruction

manual.

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 4

Cutting off the water and electricity supplies

Cleaning the washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 5

General safety

Disposal

Description of the washer-dryer, 6-7

Control panel

Display

How to run a wash cycle or a drying cycle, 8

Wash cycles and options, 9-10

Table of wash cycles

Wash options

Push&Wash+Dry

Detergents and laundry, 11-12

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Special wash cycles

Load balancing system

Troubleshooting, 13

Service, 14

XWDE 861480

English,1

GB

FR

Français,15

DE

Deutsch,29

NL

Nederlands,57

PL

Polski,43

CZ

Česky,71

2

GB

! This instruction manual should be kept in a safe

place for future reference. If the washer-dryer is

sold, transferred or moved, make sure that the

instruction manual remains with the machine so

that the new owner is able to familiarise himself/

herself with its operation and features.

! Read these instructions carefully: they contain

vital information relating to the safe installation

and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washer-dryer from its packaging.

2. Make sure that the washer-dryer has not been

damaged during the transportation process. If

it has been damaged, contact the retailer and

do not proceed any further with the installation

process.

3. Remove the 4

protective screws (used

during transportation)

and the rubber washer

with the corresponding

spacer, located on

the rear part of the

appliance (see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will

need them again if the washer-dryer needs to

be moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washer-dryer on a flat sturdy floor,

without resting it up against walls, furniture

cabinets or anything else.

2. If the floor is not

p e r f e c t l y l e v e l ,

c o m p e n s a t e f o r

any unevenness by

tightening or loosening

the adjustable front

feet (see figure); the

angle of inclination,

measured in relation to

the worktop, must not

exceed 2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive

noise and prevent it from shifting while it is

operating. If it is placed on carpet or a rug, adjust

the feet in such a way as to allow a sufficient

ventilation space underneath the washer-dryer.

Connecting the electricity and

water supplies

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it

to a cold water tap

using a ¾ gas threaded

connection (see figure).

Before performing the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the inlet

hose to the washer-

dryer by screwing it

onto the corresponding

water inlet of the

appliance, which is

situated on the top

right-hand side of

the rear part of the

appliance (see figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical details table

(see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

Installation

3

GB

Connecting the drain hose

Connect the drain

hose, without bending

it, to a drainage duct or

a wall drain located at a

height between 65 and

100 cm from the floor;

alternatively, rest it on

the side of a washbasin

or bathtub, fastening

the duct supplied to

the tap (see figure).

The free end of the

hose should not be

underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose and

must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

•thesocket isearthed and complies with all

applicable laws;

•thesocketisabletowithstandthemaximum

power load of the appliance as indicated in the

Technical data table (see opposite);

•thepowersupplyvoltagefallswithinthevalues

indicated in the Technical data table (see

opposite);

•thesocketiscompatiblewiththeplugofthe

washer-dryer. If this is not the case, replace

the socket or the plug.

! The washer-dryer must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to

rain, storms and other weather conditions.

! When the washer-dryer has been installed, the

electricity socket must be within easy reach.

! Do not use extension cords or multiple sockets.

65 - 100 cm

! The cable should not be bent or compressed.

! The power supply cable must only be replaced

by authorised technicians.

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle

“Auto Clean” (see “Cleaning the washer-dryer”).

Technical data

Model

XWDE 861480

Dimensions

width 59.5 cm

height 85 cm

depth 54 cm

Capacity

from 1 to 8 kg for wash

programme

from 1 to 6 kg for the drying

programme

Electrical

connections

please refer to the technical

data plate fixed to the machine

Water con-

nections

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 58 litres

Spin speed

up to 1400 rotations per

minute

Energy ra-

ted

programmes

according to

regulation

EN 50229

wash: programme 8; tem-

perature 60°C; using a load

of 8 kg.

drying: select the 8 wash

programme and set the

drying level to “ ”, for both

loads. The first drying cycle

must be carried out with the

nominal load.

This appliance conforms to

the following EC Directives:

- EMC 2014/30/EU (Electro-

magnetic Compatibility)

- LVD 2014/35/EU (Low

Voltage)

- 2012/19/EU - WEEE

4

GB

Care and maintenance

Cleaning the pump

The washer-dryer is fitted with a self-

cleaning pump which does not require any

maintenance. Sometimes, small items (such

as coins or buttons) may fall into the protective

pre-chamber at the base of the pump.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. Take off the cover

panel on the front

of the machine by

first pressing it in

the centre and then

pushing downwards

on both sides until

you can remove it

(see figures).

2. Unscrew the lid

by rotating it anti-

clockwise (see figure):

a little water may

trickle out. This is

perfectly normal.

3. Clean the inside thoroughly.

4. Screw the lid back on.

5. Reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Cutting off the water and electricity

supplies

•Turnoffthewatertapaftereverywashcycle.

This will limit wear on the hydraulic system inside

the washer-dryer and help to prevent leaks.

•Unplugthewasher-dryerwhencleaningitand

during all maintenance work.

Cleaning the washer-dryer

•Theouterpartsandrubbercomponents

of the appliance can be cleaned using a soft

cloth soaked in lukewarm soapy water. Do not

use solvents or abrasives.

•Thewasher-dryerhasa“AutoClean”

programme for its internal parts that must be

run with no load in the drum.

For maximum performance you may want

to use either the detergent (i.e. a quantity

10% the quantity specified for lightly-soiled

garments) or special additives to clean the

washer-dryer. We recommend running a

cleaning programme every 40 wash cycles.

To start the programme press buttons A and

B simultaneously for 5 seconds (see figure).

The programme will start automatically and

will last approximately 70 minutes. To stop the

cycle press the START/PAUSE button.

Cleaning the detergent dispenser

drawer

To remove the drawer,

press lever (1) and pull

the drawer outwards

(2) (see figure).

Wash it under running

water; this procedure

should be repeated

frequently.

Caring for the door and drum of your

appliance

•Alwaysleavetheportholedoorajarinorderto

prevent unpleasant odours from forming.

2

1

2

3

A

B

5

GB

Precautions and tips

! This washer-dryer was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons and must

therefore be read carefully.

General safety

•Thisappliancewasdesignedfordomesticuseonly.

•Thisappliancecanbeusedbychildrenaged

from 8 years and above and persons with

reduced physical, sensory or mental capabilities

or lack of experience and knowledge if they

have been given supervision or instruction

concerning use of the appliance in a safe

way and understand the hazards involved.

Children shall not play with the appliance.

Cleaning and user maintenance shall not

be made by children without supervision.

– Do not dry unwashed items in the tumble dryer.

– Items that have been soiled with substances

such as cooking oil, acetone, alcohol, petrol,

kerosene, spot removers, turpentine, waxes

and wax removers should be washed in hot

water with an extra amount of detergent before

being dried in the tumble dryer.

– Items such as foam rubber (latex foam),

shower caps, waterproof textiles, rubber

backed articles and clothes or pillows fitted

with foam rubber pads should not be dried in

the tumble dryer.

– Fabric softeners, or similar products, should

be used as specified by the fabric softener

instructions.

– The final part of a tumble dryer cycle occurs

without heat (cool down cycle) to ensure that the

items are left at a temperature that ensures that

the items will not be damaged.

WARNING: Never stop a tumble dryer before

the end of the drying cycle unless all items are

quickly removed and spread out so that the

heat is dissipated.

•Donottouchthemachinewhenbarefootorwithwetor

damp hands or feet.

•Donotpullonthepowersupplycablewhenunpluggingthe

appliance from the electricity socket. Hold the plug and pull.

•Do notopen the detergentdispenserdrawer while the

machine is in operation.

•Donottouchthedrainedwaterasitmayreachextremely

high temperatures.

•Neverforcetheportholedoor.Thiscoulddamagethesafety

lock mechanism designed to prevent accidental opening.

•If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

•Alwayskeepchildrenwellawayfromtheappliancewhile

it is operating.

•Thedoorcanbecomequitehotduringthewashcycle.

•Iftheappliancehastobemoved,workinagroupoftwo

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

•Beforeloadinglaundryintothewasher-dryer,makesure

the drum is empty.

• Duringthedryingphase,thedoortendstogetquitehot.

• Donotusetheappliancetodryclothesthat

have been washed with flammable solvents

(e.g. trichlorethylene).

• Donotusetheappliancetodryfoamrubber

or similar elastomers.

• Makesurethatthewatertapisturnedonduring 

the drying cycles.

• Childrenoflessthan3yearsshouldbekept

away from the appliance unless continuou-

sly supervised.

• Remove all objects frompockets such as

lighters and matches.

Disposal

•Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The EuropeanDirective2012/19/EU (WEEE) onWaste

Electrical and Electronic Equipment, requires that old

household electrical appliances must not be disposed

of in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to optimise

the recovery and recycling of the materials they contain and

reduce the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the product

reminds you of your obligation, that when you dispose of

the appliance it must be separately collected. Consumers

should contact their local authority or retailer for information

concerning the correct disposal of their old appliance.

6

GB

Description of the washer-dryer

Control panel

TEMPERATURE

button

WASH

CYCLE

SELECTOR

KNOB

Detergent dispenser drawer

ON/OFF

button

SPIN

button

START/PAUSE

button

and indicator light

DELAYED

START

button

OPTION

buttons

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

ON/OFF button: press this briefly to switch the

machine on or off. The START/PAUSE indicator light which

flashes slowly in a green colour shows that the machine

is switched on. To switch off the washer-dryer during the

wash cycle, press and hold the button for approximately 3

seconds; if the button is pressed briefly or accidentally the

machine will not switch off.

If the machine is switched off during a wash cycle, this

wash cycle will be cancelled.

PUSH&WASH+DRY button: (see “Wash cycles and

options”).

WASH CYCLE SELECTOR KNOB: used to set the

desired wash cycle (see “Table of wash cycles”).

OPTION buttons: press to select the available options.

The indicator light corresponding to the selected option will

remain lit.

TEMPERATURE button: press to reduce or

completely exclude the temperature; the value appears on

the display.

SPIN button: press to reduce or completely exclude

the spin cycle; the value appears on the display.

DELAYED START button: press to set a delayed

start for the selected wash cycle; the delay period appears

on the display.

DRYING button : press to decrease or exclude drying;

the selected drying level or time will appear on the display

(see “How to run a wash cycle or a drying cycle”).

START/PAUSE button and indicator light: when the

green indicator light flashes slowly, press the button to

start a wash cycle. Once the cycle has begun the indicator

light will remain lit in a fixed manner. To pause the wash

cycle, press the button again; the indicator light will flash

in an amber colour. If the symbol is not illuminated, the

door may be opened. To start the wash cycle from the

point at which it was interrupted, press the button again.

Standby mode

This washer-dryer, in compliance with new energy saving

regulations, is fitted with an automatic standby system

which is enabled after about 30 minutes if no activity is

detected. Press the ON-OFF button briefly and wait for the

machine to start up again.

Consumption in off-mode: 0,5 W

Consumption in Left-on: 8 W

DISPLAY

PUSH&WASH+DRY

button

DRYING

button

7

GB

The display is useful when programming the machine and provides a great deal of information.

The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED

START option has been set, the countdown to the start of the selected wash cycle will appear.

Pressing the corresponding button allows you to view either the maximum spin speed, temperature and drying time values

attained by the machine during the set wash cycle, or the values selected most recently (if compatible with the set wash

cycle).

The hour-glass flashes while the machine processes the data on the basis of the selected programme. After a maximum of

10 minutes, the icon remains lit in a fixed manner and the final amount of time remaining is displayed. The hour-glass icon

will then switch off approximately 1 minute after the final amount of time remaining has appeared.

The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle

appear in section B:

Main wash

Rinse

Spin/Drain

Drying

The “delay” symbol , when lit, indicates that the set “delayed start” value has appeared on the display.

There are three levels in section C concerning the washing options.

Section D includes the icons related to the three different drying levels as well as the icon , which lights up when a timed

drying option is set.

DOOR LOCKED indicator light:

The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the

door.

To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched

off the door may be opened.

Display

B

D

A

C

8

GB

How to run a wash cycle or a

drying cycle

Rapid programming

1. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

2. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the relevant

compartments as described in “Detergents and laundry”.

3. CLOSE THE DOOR.

4. Press the “PUSH&WASH+DRY” button to start the

programme.

Traditional programming

1. SWITCH THE MACHINE ON. Press the button;

the START/PAUSE indicator light will flash slowly in a

green colour.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

3. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the relevant

compartments as described in “Detergents and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Use the WASH CYCLE

SELECTOR knob to select the desired wash cycle. A

temperature and spin speed is set for each wash cycle;

these values may be adjusted. The duration of the cycle

will appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant buttons:

Modify the temperature and/or spin

speed. The machine automatically displays the

maximum temperature and spin speed values set for

the selected cycle, or the most recently-used settings

if they are compatible with the selected cycle. The

temperature can be decreased by pressing the

button, until the cold wash “OFF” setting is reached.

The spin speed may be progressively reduced by

pressing the button, until it is completely excluded

(the “OFF” setting). If these buttons are pressed again,

the maximum values are restored.

! Exception: if the 8 programme is selected, the

temperature can be increased up to a value of 90°C.

Setting the drying cycle

The first time the button is pressed, the machine will

automatically select the maximum drying cycle which is

compatible with the selected wash cycle. Subsequent

presses will decrease the drying level and then the drying

time, until the cycle is excluded completely (“OFF”).

Drying may be set as follows:

A- Based on the desired laundry dryness level:

Cupboard : suitable for laundry which can be put

back in a cupboard without being ironed.

Hanger : ideal for clothes which do not need to be

dried fully.

Iron : suitable for clothes which will need ironing

afterwards. the remaining dampness softens creases,

making them easier to remove.

B - Based on a set time period: between 210 and 30 minutes

If your laundry load to be washed and dried is much

greater than the maximum stated load (see adjacent

table of wash cycles), perform the wash cycle, and when

the cycle is complete, divide the garments into groups

and put some of them back in the drum. At this point,

follow the instructions provided for a “Drying only” cycle.

Repeat this procedure for the remainder of the load.

Note: a cooling-down period is always added to the end

of each drying cycle.

Drying only

Press button to perform the drying-only cycle.

After selecting the desired cycle (compatible with the type

of garments), press button to exclude the washing

phase and start the drying phase at the maximum level

for the selected cycle. The drying level or time may be set

and changed by pressing the drying button .

(Not compatible with cycles 13 and 14).

Setting a delayed start.

To set a delayed start for the selected cycle, press the

corresponding button repeatedly until the required delay

period has been reached. When this option has been

activated, the symbol lights up on the display. To

remove the delayed start setting, press the button until

the text “OFF” appears on the display.

Modify the cycle settings.

• Pressthebuttontoenabletheoption;theindicator

light corresponding to the button will switch on.

• Pressthebuttonagaintodisabletheoption;the

indicator light will switch off.

! If the selected option is not compatible with the set

wash cycle, the indicator light will flash and the option

will not be activated.

! If the selected option is not compatible with another

previously selected option, the indicator light will

flash accompanied by a buzzer (3 beeps), and only

the latter option will be activated; the indicator light

corresponding to the activated option will turn on.

! The options may affect the recommended load value

and/or the duration of the cycle.

7. START THE WASH CYCLE. Press the START/PAUSE

button. The corresponding indicator light will turn green,

remaining lit in a fixed manner, and the door will be locked

(the DOOR LOCKED symbol will be lit). To change a

wash cycle while it is in progress, pause the washer-

dryer using the START/PAUSE button (the START/PAUSE

indicator light will flash slowly in an amber colour); then

select the desired cycle and press the START/PAUSE

button again. To open the door while a cycle is in progress,

press the START/PAUSE button; if the DOOR LOCKED

symbol is switched off the door may be opened. Press the

START/PAUSE button again to restart the wash cycle from

the point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This will be

indicated by the text “END” on the display; when the

DOOR LOCKED symbol switches off the door may

be opened. Open the door, unload the laundry and

switch off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the button. The cycle will be stopped

and the machine will switch off.

9

GB

Wash cycles and options

Table of wash cycles

Wash options

- If the selected option is not compatible with the set

wash cycle, the indicator light will flash and the option

will not be activated.

Stain removal

Thisoptionallowsforselectingthetypeofdirtsoasto

optimally adjust the cycle for removing the stains. The

following types of dirt can be selected:

- Food, for stains caused by foodstuffs and beverages,

for example.

- Work, for grease and ink stains, for example.

- Outdoor, for mud and grass stains, for example.

! The wash cycle duration varies according to the type of

selected dirt.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 50229: select wash cycle 8 with a temperature of 60°C.

2) Long wash cycle for cottons: select wash cycle 10 with a temperature of 40.

* If you select programme and exclude the spin cycle, the machine will drain only.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-

ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Drying

Maximum load

for drying (Kg)

Detergents

Maximum load

for washing (Kg)

Cycle duration

Prewash

Wash

Fabric

softener

Bleach

Special

The duration of the wash cycles can be checked on the display.

1

Sport

30° 600



4

-

 

-

4

2

Dark

30° 800



3

-

 

-

5

3

Anti-odour (Cotton) 60° 1000



3,5

-

 

-

3,5

3

Anti-odour (Synthetic) 40° 1000



3,5

-

 

-

3,5

4

Delicate

30° 0



1

-

 

-

1

5

Wool: for wool, cashmere, etc. 40° 800



2

-

 

-

2

6

Rapid 30’

30° 800



3,5

-

 

-

3,5

Standard

7

Cottons with Pre-wash: extremely soiled whites. 90° 1400



6

  

-

8

Cotton Standard 60° (1-2): heavily soiled whites and resistant colours.

60°

(Max. 90°)

1400



6

-

 

-

8

9

Synthetic: heavily soiled resistant colours. 60° 1000



4

-

 

-

4,5

10

Coloured

40° 1400



6

-

 

-

8

11

Eco Cotton 20°: lightly soiled whites and delicate colours. 20° 1400



6

-

 

-

8

12

Eco Synthetic

20° 1000



6

-

 

-

8

Automatic

13

Wash&Dry 45’

30° 1400



1

-

 

-

1

14

AirFresh

- -



1,5

- - - -

-

Partials

Rinse/Bleach - 1400



6

- -

 

8

Spin + Drain - 1400



6

- - - -

8

Drain only * - OFF

- - - - - -

8

10

GB

Push&Wash+Dry

This function makes it possible to start an automatic wash and drying cycle either when the machine is off without having to

press the ON/OFF button in advance, or after switching on the machine without having activated any button and/or selector

(otherwise the Push&Wash+Dry function will be deactivated). To start the Push&Wash+Dry cycle press and hold the button

for 2 seconds. The indicator lights up to show that the cycle has started. The wash and drying cycle is ideal for cotton or

synthetic fabrics, as it washes them at a temperature of 30° and a maximum spin speed of 1000 rpm. During the drying

cycle the maximum temperature is 60°C. At the end of the cycle the residual humidity will be the same as for the “ ” level.

Max recommended load 3 kg.

The time displayed is the maximum time allowed by the Push&Wash+Dry cycle. If the load is lower than the maximum load

or most garment are made of synthetic materials, the actual time of the cycle will be shorter.

How does it work?

1. Load the laundry (cotton and/or synthetic garments) and close the door.

2. Pour the detergent and/or additives.

3. Start the cycle by pressing and holding the Push&Wash+Dry button for 2 seconds. The relevant indicator light will turn

green and the door will lock (the DOOR LOCKED symbol is lit).

NB: starting the cycle through the Push&Wash+Dry button activates an automatic non-customisable wash and drying cycle

recommended for cotton and synthetic fabrics.

4. The automatic cycle can be used only for washing, excluding the drying phase. Press the Push&Wash+Dry button and

then the drying button : the drying icon of the “ ” level will switch off. Maximum load for washing-only is 4 kg. The cycle

cannot be customised further.

To open the door while an automatic cycle is under way, press the START/PAUSE button. If the DOOR LOCKED symbol is

off, the door may be opened only during the washing phase. Press the START/PAUSE button again to restart the wash cycle

from the point at which it was interrupted.

5. At the end of the wash cycle the word END will light up.

11

GB

Detergents and laundry

Detergent dispenser drawer

Successful washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in

fact cause build up on the inside of your appliance and

contribute to environmental pollution.

! Do not use hand washing detergents because these

create too much foam.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

Open the detergent

dispenser drawer and pour

in the detergent or washing

additive, as follows.

Compartment 1: Pre-wash detergent (powder)

Before pouring in the detergent, make sure that extra

compartment 4 has been removed.

Compartment 2: Washing detergent (powder or liquid)

If liquid detergent is used, it is recommended that the

removable plastic partition A (supplied) be used for proper

dosage. If powder detergent is used, place the partition

into slot B.

Compartment 3: Additives (fabric softeners, etc.)

The fabric softener must not exceed the “max” level indicated

on the central pin.

Extra compartment 4: Bleach

Bleach cycle

Insert the additional compartment 4 (provided) into

compartment 1. In pouring the bleach do not exceed the

“max” level indicated on the central pin.

Perform bleaching by pouring the bleach into additional

compartment 4 and set the programme .

! Traditional bleach should be used on resistant white

fabrics, and delicate bleach for coloured and synthetics

fabrics and for wool.

Preparing the laundry

• Dividethelaundryaccordingto:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Emptyallgarmentpocketsandcheckthebuttons.

• Do not exceed the valueslisted in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1.200 g

1 towel 150-250 g

Special wash cycles

Sport (programme 1) is designed for washing lightly soiled

sports clothing (tracksuits, shorts, etc.); for best results, we

recommend not exceeding the maximum load indicated

in the “Table of wash cycles”. We recommend using liquid

detergent, and adding the amount suitable for a half-load.

Dark: use programme 2 to wash dark-coloured garments.

This programme is designed to maintain dark colours over

time. We recommend using a liquid detergent for the best

results when washing dark-coloured garments.

When you select the drying function, at the end of the

washing cycle the machine will automatically perform a

delicate drying cycle that preserves the colours of the

garments. The display will show the level “ ”.

Max. load: 3 kg.

Anti-odour: use programme 3 for washing garments

with bad odours (e.g. smoke, sweat, fried food). The

programme is designed to remove bad odours while

preserving the fabric fibres. Synthetics fabrics or mixed

loads should be washed at 40°, and resistant cotton

fabrics at 60°.

Delicate: use programme 4 to wash very delicate

garments. It is advisable to turn the garments inside out

before washing them. For best results, use liquid detergent

on delicate garments.

When selecting an exclusively time-based drying function,

a drying cycle is performed at the end of the wash cycle

that is particularly delicate, thanks to light handling and

appropriate temperature control of the water jet.

The recommended durations are:

1 kg of synthetic garments --> 150 min

1 kg of synthetic and cotton garments --> 180 min

1 kg of cotton garments --> 180 min

The degree of dryness depends on the load and fabric

composition.

Wool: the wool wash programme of this machine has

been tested and approved by The Woolmark Company

for the washing of wool containing garments labelled as

“hand wash” provided that the garments are washed

according to the instructions on the garment label and

those issued by the manufacturer of this washer-dryer.

(M1318)

In UK, Eire, Hong Kong and India the Woolmark trade mark

is a Certification trade mark.

Rapid 30’ (programme 6) this programme is designed to

wash lightly soiled garments at 30° (excluding wool and

silk) with a 3 kg maximum load in a short time: it only lasts

30 minutes and allows for saving time and energy.

Coloured: use this programme 10 to wash bright

coloured clothes. The programme is designed to maintain

bright colours over time.

Eco Cotton 20° (programme 11) ideal for lightly soiled

cotton loads. The effective performance levels achieved at

cold temperatures, which are comparable to washing at

40°, are guaranteed by a mechanical action which operates

at varying speed, with repeated and frequent peaks.

12

GB

Eco Synthetic (programme 12) ideal for mixed loads

(cotton and synthetics) with a normal soil level. The

effective performance levels achieved at cold temperatures

are guaranteed by a mechanical action which operates at

varying speed, across set average intervals.

Wash&Dry 45’ select programme

13

for washing and

drying lightly soiled garments (Cotton and Synthetic) in a

short time. This cycle may be used to wash and dry a

laundry load of up to 1 kg in just 45 minutes. To achieve

optimum results, use liquid detergent and pre-treat cuffs,

collars and stains.

AirFresh (programme

14

) ideal cycle to refresh garments

and remove bad odours, in particular smoke, from cotton

and synthetic items in 30’ (max 1.5kg) without the washing

phase.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a uniform

manner, the drum rotates continuously at a speed which

is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the load is

excessively unbalanced, the washer-dryer performs the

distribution process instead of spinning. To encourage

improved load distribution and balance, we recommend

small and large garments are mixed in the load.

13

GB

Troubleshooting

Your washer-dryer could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”), make

sure that the problem cannot be solved easily using the following list.

Problem:

The washer-dryer does not switch

on.

The wash cycle does not start.

The washer-dryer does not fill

with water (the text “H2O” on the

display).

The washer-dryer continuously

takes in and drains water.

The washer-dryer does not drain

or spin.

The washer-dryer vibrates a lot

during the spin cycle.

The washer-dryer leaks.

The “option” and START/PAUSE

indicator lights flash rapidly and an

error code appears on the display

(e.g.: F-01, F-..).

There is too much foam.

Push & Wash does not activate.

The washer-dryer does not dry.

Possible causes / Solutions:

•Theapplianceisnotpluggedintothesocketfully,ornotenoughtomakecontact.

•Thereisnopowerinthehouse.

•Thewasher-dryerdoorisnotclosedproperly.

•TheON/OFFbuttonhasnotbeenpressed.

•TheSTART/PAUSEbuttonhasnotbeenpressed.

•Thewatertaphasnotbeenopened.

•Adelayedstarthasbeenset.

•Thewaterinlethoseisnotconnectedtothetap.

•Thehoseisbent.

•Thewatertaphasnotbeenopened.

•Thereisnowatersupplyinthehouse.

•Thepressureistoolow.

•TheSTART/PAUSEbuttonhasnotbeenpressed.

•Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor

(see “Installation”).

•Thefreeendofthehoseisunderwater(see “Installation”).

•Thewalldrainagesystemisnotfittedwithabreatherpipe.

If the problem persists even after these checks, turn off the water tap, switch the

appliance off and contact the Technical Assistance Service. If the dwelling is on one

of the upper floors of a building, there may be problems relating to water drainage,

causing the washer-dryer to fill with water and drain continuously. Special anti-

draining valves are available in shops and help to prevent this inconvenience.

•Thewashcycledoesnotincludedraining:somecyclesrequirethedraining

process to be enabled manually.

•Thedrainhoseisbent(see “Installation”).

•Thedrainageductisclogged.

•Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).

•Thewasher-dryerisnotlevel(see “Installation”).

•Thewasher-dryeristrappedbetweencabinetsandwalls(see “Installation”).

•Thewaterinlethoseisnotscrewedonproperly(see “Installation”).

•Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care

and maintenance”).

•Thedrainhoseisnotfixedproperly(see “Installation”).

•Switchoffthemachineandunplugit,waitforapproximately1minuteandthen

switch it back on again.

If the problem persists, contact the Technical Assistance Service.

•Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext“for

washer-dryers” or “hand and machine wash”, or the like).

•Toomuchdetergentwasused.

• AfterswitchingonthemachineacontrolotherthanPush&Wash+Drywas 

activated. Switch the machine off and press the Push&Wash+Dry button.

• Theapplianceisnotpluggedintothesocket,ornotenoughtomakecontact.

• Therehasbeenapowerfailure.

• Theappliancedoorisnotshutproperly.

• ADELAYTIMERhasbeenset.

• DRYINGisintheOFF position.

14

GB

Service

Before contacting the Technical Assistance Service:

• Checkwhetheryoucansolvetheproblemalone(see“Troubleshooting”).

• Restartthewashcycletocheckwhethertheproblemhasbeensolved.

• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentre.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• thetypeofproblem;

• theappliancemodel(Mod.);

• theserialnumber(S/N).

This information can be found on the data plate applied to the rear of the washer-dryer, and can also be found on the front of

the appliance by opening the door.

FR

15

Français

FR

Lavante-séchante

! Ce symbole vous rappelle de lire ce mode

d’emploi.

Sommaire

Installation, 16-17

Déballage et mise à niveau

Raccordements eau et électricité

Premier cycle de lavage

Caractéristiques techniques

Entretien et soin, 18

Coupure de l’arrivée d’eau et du courant

Nettoyage du lavante-séchante

Nettoyage du tiroir à produits lessiviels

Entretien du hublot et du tambour

Nettoyage de la pompe

Contrôle du tuyau d’arrivée de l’eau

Précautions et conseils, 19

Sécurité générale

Mise au rebut

Description du lavante-séchante, 20-21

Bandeau de commandes

Écran

Comment effectuer un cycle de lavage

ou un séchage, 22

Programmes et options, 23-24

Tableau des programmes

Options de lavage

Push&Wash+Dry

Produits lessiviels et linge, 25-26

Tiroir à produits lessiviels

Cycle blanchissage

Triage du linge

Programmes spéciaux

Système d’équilibrage de la charge

Anomalies et remèdes, 27

Assistance, 28

XWDE 861480

Mode d’emploi

16

FR

Installation

! Conserver ce mode d’emploi pour pouvoir

le consulter à tout moment. En cas de vente,

de cession ou de déménagement, veiller à ce

qu’il suive toujours le lavante-séchante pour

que son nouveau propriétaire soit informé sur

son mode de optionnement et puisse profiter

des conseils correspondants.

! Lire attentivement les instructions: elles

fournissent des conseils importants sur

l’installation, l’utilisation et la sécurité de

l’appareil.

Déballage et mise à niveau

Déballage

1. Déballer le lavante-séchante.

2. Contrôler que le lavante-séchante n’a pas

été endommagé pendant le transport. S’il est

abîmé, ne pas le raccorder et contacter le

vendeur.

3. Enlever les 4 vis

de protection servant

au transport, le

caoutchouc et la cale,

placés dans la partie

arrière (voir figure).

4. Boucher les trous à l’aide des bouchons

plastique fournis.

5. Conserver toutes ces pièces: il faudra les

remonter en cas de transport du lavante-

séchante.

! Les pièces d’emballage ne sont pas des

jouets pour enfants.

Mise à niveau

1. Installer le lavante-séchante sur un sol plat

et rigide, sans l’appuyer contre des murs, des

meubles ou autre.

2. Si le sol n’est

pa s pa r f a i t e m e nt

horizontal, visser ou

dévisser les pieds de

réglage avant (voir

figure) pour niveler

l’appareil; son angle

d’inclinaison, mesuré

sur le plan de travail, ne

doit pas dépasser 2°.

Une bonne mise à niveau garantit la stabilité

de l’appareil et évite qu’il y ait des vibrations,

du bruit et des déplacements en cours de

optionnement. Si la machine est posée sur de

la moquette ou un tapis, régler les pieds de

manière à ce qu’il y ait suffisamment d’espace

pour assurer une bonne ventilation.

Raccordements eau et électricité

Raccordement du tuyau d’arrivée de

l’eau

1. Reliez le tuyau

d’alimentation en le

vissant à un robinet

d’eau froide à embout

fileté 3/4 gaz (voir

figure).

Faire couler l’eau

jusqu’à ce qu’elle

soit limpide et sans

impuretés avant de

raccorder.

2. Raccorder le tuyau

d’arrivée de l’eau au

lavante-séchante en

le vissant à la prise

d’eau prévue, dans la

partie arrière en haut

à droite (voir figure).

3. Attention à ce que le tuyau ne soit pas plié

ou écrasé.

! La pression de l’eau doit être comprise entre

les valeurs indiquées dans le tableau des

Caractéristiques techniques (voir page ci-

contre).

! Si la longueur du tuyau d’alimentation ne

suffit pas, s’adresser à un magasin spécialisé

ou à un technicien agréé.

! N’utiliser que des tuyaux neufs.

! Utiliser ceux qui sont fournis avec l’appareil.

FR

17

Raccordement du tuyau de vidange

Raccorder le tuyau

d’évacuation, sans

le plier, à un conduit

d’évacuation ou

à une évacuation

murale placés à

une distance du sol

comprise entre 65 et

100 cm ;

ou bien l’accrocher

à un évier ou à une

baignoire, dans ce

cas, fixer le support

en plastique fourni

avec l’appareil au

robinet (voir figure).

L’extrémité libre du

tuyau d’évacuation

ne doit pas être

plongée dans l’eau.

! L’utilisation d’un tuyau de rallonge est

absolument déconseillée mais si on ne peut

faire autrement, il faut absolument qu’il ait le

même diamètre que le tuyau original et sa

longueur ne doit pas dépasser 150 cm.

Raccordement électrique

Avant de brancher la fiche dans la prise de

courant, s’assurer que :

• lapriseestbienreliéeàlaterreetest

conforme aux réglementations en vigueur;

• lapriseestbienapteàsupporterla

puissance maximale de l’appareil indiquée

dans le tableau des Caractéristiques

techniques (voir ci-contre);

• latensiond’alimentationestbiencomprise

entre les valeurs figurant dans le tableau des

Caractéristiques techniques (voir ci-contre);

• lapriseestbiencompatibleaveclafichedu

lavante-séchante. Autrement, remplacer la

prise ou la fiche.

! Le lavante-séchante ne doit pas être installé

dehors, même à l’abri, car il est très dangereux

de le laisser exposé à la pluie et aux orages.

! Après installation du lavante-séchante,

la prise de courant doit être facilement

accessible.

! N’utiliser ni rallonges ni prises multiples.

! Le câble ne doit être ni plié ni trop écrasé.

! Le câble d’alimentation ne doit être remplacé

que par des techniciens agréés.

65 - 100 cm

Attention! Nous déclinons toute responsabilité

en cas de non-respect des normes

énumérées ci-dessus.

Premier cycle de lavage

Avant la première mise en service de l’appareil,

effectuer un cycle de lavage avec un produit

lessiviel mais sans linge et sélectionner

le programme «AUTO NETTOYANT» (voir

“Nettoyage du lavante-séchante”).

Caractéristiques techniques

Modèle

XWDE 861480

Dimensions

largeur 59,5 cm

hauteur 85 cm

profondeur 54 cm

Capacité

de 1 à 8 kg pour le lavage

de 1 à 6 kg pour le séchage

Raccorde-

ments élec-

triques

Voir la plaque signalétique

appliquée sur la machine

Raccor-

dements

hydrauli-

ques

pression maximale

1 MPa (10 bar)

pression minimale

0,05 MPa (0,5 bar)

capacité du tambour 58 litres

Vitesse

d’essorage

jusqu’à 1400 tours minute

Program-

mes de

contrôle

selon la rè-

glements

EN 50229

lavage: programme 8; tem-

pérature 60°C; effectué avec

une charge de 8 kg.

séchage: sélectionner le

programme de lavage 8 et

sélectionner le degré de sé-

chage « », pour les deux

charges. Le premier sécha-

ge doit être effectué avec la

charge nominale.

Cet appareil est conforme

aux Directives Communau-

taires suivantes:

- EMC 2014/30/EU (Com-

patibilité électromagnétique)

- 2012/19/EU - WEEE

- LVD 2014/35/EU (Basse

Tension)

18

FR

Entretien et soin

Coupure de l’arrivée d’eau et du

courant

• Fermerlerobinetdel’eauaprèschaque

lavage. Cela réduit l’usure de l’installation

hydraulique du lavante-séchante et évite

tout danger de fuites.

• Débrancherlafichedelaprisedecourant

lors de tout nettoyage du lavante-séchante

et pendant tous les travaux d’entretien.

Nettoyage du lavante-séchante

• Pournettoyerl’extérieuretlespartiesen

caoutchouc, utiliser un chiffon imbibé d’eau tiède

et de savon. N’utiliser ni solvants ni abrasifs.

•Celavante-séchanteestéquipéd’un

programme «AUTO NETTOYANT» des parties

internes qui doit être effectué tambour

complètement vide.

La lessive (dans une quantité égale à 10% de

celle conseillée pour du linge peu sale) ou les

additifs spéciaux pour le nettoyage du lavante-

séchante, pourront être utilisés comme

adjuvants dans le programme de lavage. Il

est conseillé d’effectuer le programme de

nettoyage tous les 40 cycles de lavage.

Pour activer le programme, appuyer

simultanément sur les touches A et B pendant

5 secondes (voir figure). Le programme

démarrera automatiquement et durera environ

70 minutes. Pour stopper le cycle, appuyer

sur la touche START/PAUSE.

Nettoyage du tiroir à produits

lessiviels

Pour sortir le tiroir,

appuyer sur le levier (1)

et tirer vers soi (2) (voir

figure).

Le laver à l’eau

courante ; effectuer

cette opération assez

souvent.

2

1

Entretien du hublot et du tambour

•Ilfauttoujourslaisserlehublotentrouvert

pour éviter la formation de mauvaise odeurs.

Nettoyage de la pompe

Le lavante-séchante est équipé d’une pompe

autonettoyante qui n’exige aucune opération

d’entretien. Il peut toutefois arriver que de

menus objets (pièces de monnaie, boutons)

tombent dans la préchambre qui protège la

pompe, placée en bas de cette dernière.

! S’assurer que le cycle de lavage est bien

terminé et débrancher la fiche.

Pour accéder à cette préchambre :

1. retirer le panneau

situé à l’avant du

lavante-séchante

en appuyant vers

le centre. Appuyer

ensuite vers le bas

de chaque côté et

l’extraire (voir figures).

2. dévisser le

couvercle en le

tournant dans le sens

inverse des aiguilles

d’une montre (voir

figure) : il est normal

qu’un peu d’eau

s’écoule;

3. nettoyer soigneusement l’intérieur;

4. revisser le couvercle;

5. remonter le panneau en veillant à bien enfiler

les crochets dans les fentes prévues avant de

le pousser contre l’appareil.

Contrôle du tuyau d’arrivée de

l’eau

Contrôler le tuyau d’alimentation au moins

une fois par an. Procéder à son remplacement

en cas de craquèlements et de fissures : car

les fortes pressions subies pendant le lavage

pourraient provoquer des cassures.

! N’utiliser que des tuyaux neufs.

1

2

3

A

B

FR

19

Précautions et conseils

! Ce lavante-séchante a été conçu et fabriqué

conformément aux normes internationales de sécurité.

Ces consignes sont fournies pour des raisons de sécurité,

il faut les lire attentivement.

Sécurité générale

•Cetappareilestconçupourunusagedomestique.

• Cet appareil peut être utilisé par les enfants

à partir de 8 ans et par les personnes dont

les capacités physiques, sensorielles ou

mentales sont réduites ou qui ne disposent

pas des connaissances suffisantes, à

condition qu’ils soient encadrés ou aient été

formés de façon appropriée pour l’utilisation

de l’appareil de façon sûre et en comprenant

les dangers qui y sont liés. Les enfants ne

doivent pas jouer avec l’appareil. L’entretien

et le nettoyage ne doivent pas être effectués

par les enfants sans surveillance.

- Ne pas mettre sécher du linge non lavé.

- Le linge contaminé avec des substances

telles que de l’huile de cuisson, de

l’acétone, de l’alcool, de l’essence, du

kérosène, des détachants, de l’essence de

térébenthine, de la cire et des substances

pour l’enlever, doit être lavé à l’eau chaude

avec une dose supplémentaire de lessive

avant d’être introduit dans le sèche-linge.

- Des objets en mousse expansée (mousse

de latex), des bonnets de douche, des textiles

imperméables, des articles doublés de

caoutchouc et des vêtements ou des coussins

ayant des parties en mousse de latex ne

doivent pas être séchés en sèche-linge.

- En cas d’utilisation d’assouplissants ou

de tout autre produit similaire, se conformer

aux instructions du fabricant.

- La partie finale d’un cycle du sèche-linge se

produit sans chaleur (cycle de refroidissement)

pour éviter tout endommagement du linge.

ATTENTION: Ne jamais arrêter le sèche-linge

avant la fin du programme de séchage. Dans

ce cas, sortir immédiatement tout le linge et

l’étendre pour le faire refroidir rapidement.

• Cetappareilestconçupourunusagedomestique.

• Nejamaistoucherl’appareilsil’onestpiedsnusetsi

les mains sont mouillées ou humides.

• Nejamaistirersurlecâblepourdébrancherlafichede

la prise de courant.

• Nepastoucheràl’eaudevidange,ellepeutatteindre

des températures très élevées.

• Nepasforcerpourouvrirlaportehublot:leverrouillage

de sécurité qui protège contre les ouvertures

accidentelles pourrait s’endommager.

• Encasdepanne,éviteràtoutprixd’accéderaux

mécanismes internes pour tenter une réparation.

• Veilleràcequelesenfantsnes’approchentpasde

l’appareil pendant son fonctionnement.

• Deuxoutroispersonnessontnécessairespourle

déplacer en faisant très attention. Ne jamais le déplacer

tout seul car il est très lourd.

• Avantd’introduirelelinge,s’assurerqueletambourest

bien vide.

• Pendant le séchage, le hublot a tendance à chauffer.

• Ne mettez pas à sécher du linge lavé avec des

solvants inflammables (trichloréthylène par ex.).

• Ne mettez pas à sécher du caoutchouc-

mousse ou des élastomères du même genre.

• Vérifiez qu’au cours du séchage, le robinet de l’eau soit

bien ouvert.

• les enfants de moins de 3 ans doivent être

tenus à bonne distance du sèche-linge s’ils

ne sont pas sous surveillance constante.

• Enlever tous les objets des poches,

notamment les briquets et les allumettes.

Mise au rebut

•Miseaurebutdumatérield’emballage:seconformer

aux réglementations locales de manière à ce que les

emballages puissent être recyclés.

•LaDirectiveEuropéenne2012/19/EU(WEEE)surles

Déchets des Equipements Electriques et Electroniques,

exige que les appareils ménagers usagés ne soient pas

jetés dans le flux normal des déchets municipaux. Les

appareils usagés doivent être collectés séparément afin

d’optimiser le taux de récupération et le recyclage des

matériaux qui les composent et réduire l’impact sur la

santé humaine et l’environnement. Le symbole de la

‘’poubelle barrée’’ est apposée sur tous les produits

pour rappeler les obligations de collecte séparée. Les

consommateurs devront contacter les autorités locales

ou leur revendeur concernant la démarche à suivre pour

l’enlèvement de leur vieil appareil.

20

FR

Description du lavante-séchante

Bandeau de commandes

Touche

TEMPÉRATURE

BOUTON

PROGRAMMES

Tiroir à produits lessiviels

Touche ON/OFF

Touche

ESSORAGE

Touche et voyant

START/PAUSE

Touche

DÉPART

DIFFÉRÉ

Touches

OPTION

Tiroir à produits lessiviels : pour charger les produits

lessiviels et les additifs (voir “Produits lessiviels et linge”).

Touche ON/OFF : appuyer brièvement sur la touche

pour allumer ou éteindre l’appareil. Le voyant vert START/

PAUSE clignotant lentement indique que la machine

est allumée. Pour éteindre le lavante-séchante en cours

de lavage, appuyer sur la touche pendant au moins 3

secondes de suite ; une pression brève ou accidentelle

n’entraîne pas l’arrêt de l’appareil.

L’arrêt de l’appareil pendant un lavage annule le lavage en

cours.

Touche PUSH&WASH+DRY: (voir “Programmes et options”).

BOUTON PROGRAMMES: pour sélectionner le

programme désiré (voir “Tableau des programmes”).

Touches OPTION: pour sélectionner les options

disponibles. Le voyant correspondant à l’option

sélectionnée restera allumé.

Touche TEMPÉRATURE : appuyer sur cette

touche pour diminuer la température ou pour l’exclure

complètement. La valeur correspondante s’affiche à

l’écran.

Touche ESSORAGE : appuyer sur cette touche

pour diminuer la vitesse de l’essorage ou pour l’exclure

complètement. La valeur correspondante s’affiche à

l’écran.

Touche DÉPART DIFFÉRÉ : appuyer pour

sélectionner un départ différé pour le programme choisi. Le

retard est affiché à l’écran.

Touche SÉCHAGE: appuyer pour réduire ou

supprimer le séchage; le niveau ou le temps de séchage

sélectionné s’affiche à l’écran (voir “Comment faire un

cycle de lavage ou un séchage”).

Touche et voyant START/PAUSE : quand le voyant

vert clignote lentement, appuyer sur la touche pour

démarrer un lavage. Une fois le cycle lancé, le voyant

passe à l’allumage fixe. Pour activer une pause de lavage,

appuyer à nouveau sur la touche ; le voyant devient

couleur ambre et se met à clignoter. Si le symbole

n’est pas allumé, il est possible d’ouvrir le hublot. Pour

faire redémarrer le lavage exactement à l’endroit de l’arrêt,

appuyer une nouvelle fois sur la touche.

Stand-by

Ce lavante-séchante, conformément aux nouvelles normes

en vigueur dans le domaine de l’économie d’énergie, est

équipée d’un système d’extinction automatique (veille)

activé après environ 30 minutes d’inutilisation. Appuyez

brièvement sur la touche ON-OFF et attendre que la

machine soit réactivée.

Consommation en off-mode : 0,5 W

Consommation en Left-on : 8 W

ECRAN

Touche

PUSH&WASH+DRY

Touche

S

ÉCHAGE

La page charge ...

Indesit XWDE 861480X W EU Mode d'emploi

Indesit XWDE 861480X W EU Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents