LG LFD23860ST Le manuel du propriétaire

Marque: LG

Modèle: LFD23860ST

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

LFD23860SW

BOTTOM FREEZER

REFRIGERATOR

Please read this guide thoroughly

before operating and keep it handy for

reference at all times.

P/No. MFL47277107

Models / Modèles / Modelos

CONGÉLATEUR

INFÉRIEUR

RÉFRIGÉRATEUR

Veuillez lire ce manuel en entier avant de mettre

en marche l’unité et conservez-le à portée de la

main pour le consulter à tout moment.

LFC23760**, LFD23860**

Owner’s Manual

Manuel d’utilisateur

TABLE OF CONTENTS

English Version 2

French Version 36

Warranty (Canada) 3 - 4

Safety Instructions 5 - 6

Grounding Requirements 6

Parts and Features 7

Refrigerator Installation 8 - 16

Unpacking your refrigerator

Installation 8

Base Grille 8

Removing, Reversing and Replacing

Your refrigerator doors

9 - 15

Pull out drawer 15

Leveling and door alignment 16

Using your refrigerator 17 - 25

Ensuring proper air circulation 17

Multi Flow

Door alarm

Setting the controls

Adjusting control settings 18

Food storage guide 19

Storing frozen food 19

Refrigerator Section 20

Refrigerator shelves 20

Chef Fresh 21

Crisper humidity control 21

Optibin Crisper 21

Crisper cover with lattice on inner surface 22

Design-A-Door 22

Dairy Bin 22

Egg Box 22

Water Dispenser 24

Freezer Section 23

Ice Bin 23

Wire Durabase 23

Tilting Door 23

Filter

24 - 25

Care and Cleaning 26 - 27

General cleaning tips 26

Outside 26

Inside walls 26

Door liner and gaskets 26

Plastic parts 26

Condenser coils 26

Light bulb replacement 26 - 27

Power interruptions 27

When you go on vacation 27

About the Custom Cube Ice Maker 28

Connecting the Water Line 29 - 31

Trouble shooting Guide 32 - 35

Cover Back 26

LG ELECTRONICS CANADA, INC.

GARANTIE LIMITÉE DU RÉFRIGÉRATEUR LG - Canada

GARANTIE: Si votre réfrigérateur LG (le « produit ») s'avère défectueux en raison d'un défaut de matériau ou de fabrication

lors d'une utilisation normale à domicile, pendant la période de garantie spécifiée ci-après, LG Canada réparera ou

remplacera à sa discrétion le produit sur réception de la preuve d'achat originale fournie par le détaillant. Cette garantie n'est

offerte qu'à l'acheteur original du produit chez un détaillant et ne s'applique qu'à un produit distribué au Canada par LG

Canada ou par un distributeur canadien autorisé. La garantie ne s'applique qu'aux produits situés et utilisés au Canada.

PÉRIODE DE GARANTIE : (Remarque : Si la date d'achat originale ne peut être vérifiée, la garantie débutera

soixante (60) jours suivant la date de fabrication.)

Réfrigérateur/congélateur Système scellé (compresseur, condensateur et évaporateur seulement)

Pièces et main-d'œuvre

(pièces internes fonctionnelles seulement)

Pièces seulement

(Les consommateurs devront payer pour la main-d’œuvre)

µ Les produits et pièces de remplacement sont garantis pour la portion restante de la période de garantie originale ou quatre-vingt-dix (90), selon la

période la plus longue.

µ Les produits et pièces de remplacement peuvent être neufs ou remanufacturés.

µ Le centre de service autorisé LG garantit les réparations pendant trente (30) jours.

Tous les coûts associés aux circonstances exclues ci-dessus seront assumés par le consommateur.

Pièces et main-d'œuvre

Un (1) an à compter de la date

d’achat original

Un (1) an à compter de la date

d’achat original

Sept (7) ans à compter de la date

d’achat original

LA RESPONSABILITÉ DE LG CANADA SE LIMITE À LA GARANTIE CI-DESSUS. SAUF TEL QU'IL EST EXPLICITEMENT

INDIQUÉ CI-DESSUS, LG CANADA NE FOURNIT AUCUNE AUTRE GARANTIE ET REJETTE TOUTES LES AUTRES

GARANTIES ET CONDITIONS EXPLICITES OU IMPLICITES À L'ÉGARD DU PRODUIT, CE QUI INCLUT, SANS TOUTEFOIS

S'Y LIMITER, TOUTE GARANTIE ET CONDITION IMPLICITE DE QUALITÉ MARCHANDE OU DE CONVENANCE À UN USAGE

PARTICULIER ET AUCUNE DÉCLARATION NE LIERA LG CANADA. LG CANADA N'AUTORISE PERSONNE À CRÉER NI À

ASSUMER AUCUNE AUTRE PROVISION POUR GARANTIES EN RELATION AVEC CE PRODUIT. SI UNE GARANTIE OU

CONDITION IMPLICITE EST REQUISE PAR LA LOI, SA PÉRIODE SE LIMITE À CELLE DE LA GARANTIE EXPLICITE

SUSMENTIONNÉE.

LG CANADA, LE FABRICANT ET LE DISTRIBUTEUR NE POURRONT ÊTRE TENUS RESPONSABLES D'AUCUN DOMMAGE

ACCESSOIRE, CONSÉCUTIF, SPÉCIAL, DIRECT OU INDIRECT, D'AUCUNE PERTE D'ACHALANDAGE OU DE PROFITS,

D'AUCUN DOMMAGE PUNITIF, EXEMPLAIRE OU AUTRE, DIRECTEMENT OU INDIRECTEMENT ATTRIBUABLE À TOUTE

VIOLATION CONTRACTUELLE, FONDAMENTALE OU AUTRE, OU À UNE ACTION, UNE OMISSION, UN DÉLIT OU TOUTE

AUTRE CHOSE.

La présente garantie vous confère des droits légaux spécifiques. Vous pourriez disposer d'autres droits, suivant les lois provinciales

applicables. Toute clause de la présente garantie qui invalide ou modifie une condition ou garantie implicite aux termes d'une loi

provinciale est dissociable si elle entre en conflit avec la loi provinciale, et ce, sans affecter les autres clauses de la garantie.

LA PRÉSENTE GARANTIE LIMITÉE NE COUVRE PAS CE QUI SUIT:

1. Un appel de service pour livrer, ramasser ou installer le produit; renseigner un client sur le fonctionnement du produit;

réparer ou remplacer des fusibles ou rectifier le câblage; ou corriger une réparation ou installation non autorisée.

2. La défaillance du produit durant une panne ou interruption de courant ou en raison d’un service électrique inadéquat.

3. Des dommages occasionnés par la fuite ou le bris de conduites d’eau, le gel de conduites d’eau, des tuyaux de drainage

restreints, une alimentation en eau inadéquate ou interrompue ou une alimentation en air inadéquate.

4. Des dommages attribuables à l’utilisation du produit dans une atmosphère corrosive ou contraire aux instructions

spécifiées dans le manuel d’utilisation de produit.

5. Des dommages au produit causés par un accident, des animaux nuisibles ou des vermines, la foudre, le vent, un incendie,

une inondation ou une catastrophe naturelle.

6. Les dommages attribuables à une mauvaise utilisation, une utilisation abusive ou à une installation, une réparation ou un

entretien inapproprié du produit. Les réparations inappropriées incluent l’utilisation de pièces ni aprouvées ni

recommandées par LG Canada.

7. La détérioration ou la défaillance du produit causée par une modification ou un changement non autorisé ou une

utilisation autre que celle prévue, ou résultant d’ une fuite d’eau occasionée par une mauvaise installation.

8. La détérioration ou la défaillance du produit causée par un courant ou un voltage électrique incorrect, une utilisation

commerciale ou industrielle, ou l’utilisation d’accessoires, d’éléments ou de produits nettoyants non approuvés par LG Canada.

9. Les dommages causés par le transport et la manipulation, notamment les égratignures, les bosses, les écaillures et / ou tout

autre dommage à la finition du produit, à moins que ces dommages ne soient attribuables à des défauts de matériaux

ou de fabrication et qu’ils ne soient signalés dans un délai d’une (1) semaine de la livraison.

10. Des dommages ou des pièces manquantes à tout produit exposé, déballé, soldé ou remis à neuf.

11. Des produits dont le numéro de série original a été retiré, modifié ou ne peut être facilement déterminé. Le modèle et le

numéro de série, ainsi que le reçu de vente original du détaillant, sont requis pour valider la garantie.

12. L’augmentation des coûts et de la consommation des services publics.

13. Le remplacement des ampoules électriques, des filtres et de toute pièce non durable.

14. Les réparations requises si le produit ne sert pas à une utilisation domestique normale et habituelle (y compris, sans

toutefois s’y limiter, une utilisation commerciale, dans un bureau ou un centre récréatif) ou est utilisé contrairement aux

instructions spécifiées dans le manuel d’utilisation du produit.

15. Les coûts associés à l’enlèvement du produit de votre résidence aux fins de réparation.

16. L’enlèvement et la réinstallation du produit, s’il est installé à un endroit inaccesible ou contrairement aux instructions

publiées, y compris dans le manuel d’utilisation et le manuel d’installation du produit.

17. Les accesoires du produit, tels que les balconnets, les tiroirs, les poignées, les tablettes, etc. Sont également exclues

les pièces non incluses initialement avec le produit.

Pour obtenir tous les détails sur la garantie et

accéder au service à la clientèle, téléphonez-

nous ou visitez notre site Web:

Composez le 1-888-542-2623 (24 h sur 24, 365 jours par année) et

Sélectionnez l’option de menu appropriée, ou visitez notre site Web au:

http://www.lg.ca

Écrivez vos renseignements de garantie ci-dessous:

Renseignements sur l’enregistrement du produit:

Modèle:

Numéro de série:

Date d’achat:

LG ELECTRONICS CANADA, INC.

LG REFRIGERATOR LIMITED WARRANTY - Canada

WARRANTY: Should your LG Refrigerator (“Product”) fail due to a defect in material or workmanship under normal home use during the warranty

period set forth below, LG Canada will at its option repair or replace the Product upon receipt of proof of original retail purchase. This warranty is

valid only to the original retail purchaser of the product and applies only to a Product distributed in Canada by LG Canada or an authorized

Canadian distributor thereof. The warranty only applies to Products located and used within Canada.

WARRANTY PERIOD: (Note: If the original date of purchase can not be verified, the warranty will begin sixty

(60) days from the date of manufacture).

Refrigerator/Freezer Sealed System (Compressor, Condenser, and Evaporator only)

Parts and Labor Parts only

(Consumer will be charged for labor)

Parts and Labor

(internal/functional parts only)

µ Replacement products and parts are warranted for the remaining portion of the original warranty period or ninety (90) days, whichever is greater.

LG Authorized Service Center warranties their repair work for thirty (30) days

Replacement products and parts may be new or remanufactured.

LG CANADA’S SOLE LIABILITY IS LIMITED TO THE WARRANTY SET OUT ABOVE. EXCEPT AS EXPRESSLY PROVIDED ABOVE, LG

CANADA MAKES NO AND HEREBY DISCLAIMS ALL OTHER WARRANTIES AND CONDITIONS RESPECTING THE PRODUCT, WHETHER

EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE, AND NO REPRESENTATIONS SHALL BE BINDING ON LG CANADA. LG CANADA DOES

NOT AUTHORIZE ANY PERSON TO CREATE OR ASSUME FOR IT ANY OTHER WARRANTY OBLIGATION OR LIABILITY IN CONNECTION

WITH THE PRODUCT. TO THE EXTENT THAT ANY WARRANTY OR CONDITION IS IMPLIED BY LAW, IT IS LIMITED TO THE EXPRESS

WARRANTY PERIOD ABOVE. LG CANADA, THE MANUFACTURER OR DISTRIBUTOR SHALL NOT BE LIABLE FOR ANY INCIDENTAL,

CONSEQUENTIAL, SPECIAL, DIRECT OR INDIRECT DAMAGES, LOSS OF GOODWILL, LOST PROFITS, PUNITIVE OR EXEMPLARY

DAMAGES OR ANY OTHER DAMAGE, WHETHER ARISING DIRECTLY OR INDIRECTLY FROM ANY CONTRACTUAL BREACH,

FUNDAMENTAL OR OTHERWISE, OR FROM ANY ACTS OR OMISSIONS, TORT, OR OTHERWISE.

This warranty gives you specific legal rights. You may have other rights which may vary from province to province depending on applicable

provincial laws. Any term of this warranty that negates or varies any implied condition or warranty under provincial law is severable where

it conflicts with provincial law without affecting the remainder of this warranty’s terms.

All costs associated with the above excluded circumstances shall be borne by the consumer.

One (1) year from the date of original

retail purchase

One (1) year from the date of original

retail purchase

Seven (7) years from the date of original

retail purchase

For complete warranty details and customer assistance,

please call or visit our website:

Call 1-888-542-2623 (24 hours a day, 365 days a year) and

select the appropriate option from the menu, or visit our website

at http://www.lg.ca

Write your warranty information below:

Product Registration Information:

Model:

Serial Number:

Date of Purchase:

THIS LIMITED WARRANTY DOES NOT COVER:

1. Service trips to deliver, pick up, or install the product; instructing a customer on operation of the product; repair or replacement of

fuses or correction of wiring, or correction of unauthorized repairs/installation.

2. Failure of the product to perform during power failures and interruptions or inadequate electrical service.

3. Damage caused by leaky or broken water pipes, frozen water pipes, restricted drain lines, inadequate or interrupted water supply or

inadequate supply of air.

4. Damage resulting from operating the Product in a corrosive atmosphere or contrary to the instructions outlined in the Product

owner’s manual.

5. Damage to the Product caused by accidents, pests and vermin, lightning, wind, fire, floods, or acts of God.

6. Damage resulting from the misuse, abuse, improper installation, repair, or maintenance of the Product. Improper repair includes use

of parts not approved or specified by LG Canada.

7. Damage or product failure caused by unauthorized modification or alteration, or use for other than its intended purpose, or resulting

from any water leakage due to improper installation.

8. Damage or Product failure caused by incorrect electrical current, voltage, commercial or industrial use, or use of accessories,

components, or cleaning products that are not approved by LG Canada.

9. Damage caused by transportation and handling, including scratches, dents, chips, and/or other damage to the finish of your product,

unless such damage results from defects in materials or workmanship and is reported within one (1) week of delivery.

10. Damage or missing items to any display, open box, discounted, or refurbished Product.

11. Products with original serial numbers that have been removed, altered, or cannot be readily determined. Model and Serial numbers,

along with original retail sales receipt, are required for warranty validation.

12. Increases in utility costs and additional utility expenses.

13. Replacement of light bulbs, filters, or any consumable parts.

14. Repairs when your Product is used in other than normal and usual household use (including, without limitation, commercial use, in

offices or recreational facilities) or contrary to the instructions outlined in the Product owner’s manual.

15. Costs associated with removal of the Product from your home for repairs.

16. The removal and reinstallation of the Product if it is installed in an inaccessible location or is not installed in accordance with

published installation instructions, including the Product owner’s and installation manuals.

17. Accessories to the Product such as door bins, drawers, handles, shelves, etc. Also excluded are parts besides those that were

originally included with the Product.

This guide contains many important safety messages. Always read and obey all safety messages.

This is the safety alert symbol. It alerts you to safety messages that inform you of hazards that can kill or

hurt you or others, or cause damage to the product.

All safety messages will be preceded by the safety alert symbol and the hazard signal word DANGER,

WARNING, CAUTION. These words mean:

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if

the instructions are not followed.

SAFETY MESSAGES

WARNING

To reduce the risk of fire, electric shock, or injury to persons

when using your product, basic safety precautions should

be followed, including the following:

NEVER unplug your refrigerator by pulling on the power cord.

Always grip the plug firmly and pull it straight out from the outlet.

Repair or replace immediately all electric service cords that have

become frayed or otherwise damaged. Do not use a cord that

shows cracks or abrasion damage along its length or at either the

plug or connector end.

When moving your refrigerator away from the wall, be careful not

to roll over or damage the power cord.

DO NOT store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

DO NOT allow children to climb, stand or hang on the refrigerator

doors or shelves in the refrigerator. They could damage the

refrigerator and seriously injure themselves.

Keep fingers out of “pinch point” areas; clearances between the

Unplug your refrigerator before cleaning or making any repairs.

NOTE: We strongly recommend that any servicing be performed

by a qualified individual.

Before replacing a burned-out light bulb, unplug the refrigerator or

turn off power at the circuit breaker or fuse box in order to avoid

contact with a live wire filament. (A burned-out light bulb may

break when being replaced.)

NOTE: Setting either or both controls to the OFF position does not

remove power to the light circuit.

Read all instructions before using this appliance.

Use this appliance only for its intended purpose as described in

this use and care guide.

After your refrigerator is in operation, do not touch the cold

surfaces in the freezer compartment when hands are damp or

wet. Skin may adhere to the extremely cold surfaces.

In refrigerators with automatic icemakers, avoid contact with the

moving parts of the ejector mechanism, or with the heating

element that releases the cubes. DO NOT place fingers or hands

on the automatic icemaking mechanism while the refrigerator is

plugged in.

DO NOT refreeze frozen foods which have thawed completely.

The United States Department of Agriculture in Home and

Garden Bulletin No. 69 says:

“...You may safely refreeze frozen foods that have thawed if

they still contain ice crystals or if they are still cold below

40 °F (4 °C).”

“...Thawed ground meats, poultry, or fish that have any off-odor

or off-color should not be refrozen and should not be eaten.

Thawed ice cream should be discarded. If the odor or color of

any food is poor or questionable, get rid of it. The food may be

dangerous to eat.”

“Even partial thawing and refreezing reduces the eating quality

of foods, particularly fruits, vegetables and prepared foods. The

eating quality of red meats is affected less than that of many

other foods. Use refrozen foods as soon as possible to

save as much of their quality as you can.”

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

doors and cabinet are necessarily small. Be careful when you

open the doors when children are in the area.

For personal safety, this appliance must be properly grounded.

Have the wall outlet and the circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

The refrigerator-freezer should be so positioned that the supply

plug is accessible for quick disconnection when accident happens.

Do not store bottles in the freezer compartment - they may break

when frozen, causing damage.

You can be killed or seriously injured if you don’t follow instructions.

Indicates an imminently hazardous situation which, if not avoided,

may result in minor or moderate injury, or product damage only.

You will be killed or seriously injured if you don’t follow instructions.

DANGER

WARNING

CAUTION

IMPORTANT: Please read carefully.

TO CONNECT ELECTRICITY

Where a standard two-prong wall outlet is encountered, it

is your personal responsibility and obligation to have it

replaced with a properly grounded three-prong wall outlet.

Do not, under any circumstances, cut or remove the third

(ground) prong from the power cord.

NOTE: Before performing any type of installation, cleaning,

or removing a light bulb, turn the control (Thermostat,

Refrigerator Control or Freezer Control, depending on the

model) to OFF and then disconnect the refrigerator from

the electrical source. When you are finished, reconnect the

refrigerator to the electrical source and reset the control

(Thermostat, Refrigerator Control or Freezer Control,

depending on the model) to the desired setting.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain

conditions, we strongly recommend against the use of an

extension cord. However, if you still elect to use an

extension cord, it is absolutely necessary that it be a

UL-listed (in the United States), 3-wire grounding type

appliance extension cord having a grounding type plug and

outlet, and that the electrical rating of the cord be 15

amperes (minimum) and 120 volts.

Use of an extension cord will increase the clearance needed

for the back of the refrigerator.

WARNING

Electrical Shock Hazard

FOR PERSONAL SAFETY, this appliance must be

properly grounded. Have the wall outlet and the circuit

checked by a qualified electrician to make sure the

outlet is properly grounded.

Ensure proper

ground exists

before use.

3-prong

grounding

plug

3-prong

grounding type

wall receptacle

CFC DISPOSAL

GROUNDING REQUIREMENTS

Child entrapment and suffocation are not problems of the

past. Junked or abandoned refrigerators are still dangerous...

even if they will sit for “just a few days”. If you are getting rid

of your old refrigerator, please follow the instructions at right

to help prevent accidents.

WARNING

POWER CORD REPLACEMENT

If the power cord is damaged, it must be replaced

by the manufacturer, by our service center or by

qualified personal by LG Electronics, to avoid some

risk.

DANGER: RISK OF CHILD ENTRAPMENT

Your old refrigerator

may have a cooling system that used

CFCs (chlorofluorocarbons). CFCs are believed to harm

stratospheric ozone.

This appliance contains fluid (refrigerant, lubricant), is made

of parts and materials which are reusable and / or recyclable.

All the important materials should be sent to the collection

center of waste material and can be reused after rework

(recycling).

If you are throwing away your old refrigerator,

the

make sure

CFC refrigerant is removed for proper disposal by a

qualified service If you intentionally release this CFC

refrigerant, you can be subject to fines and imprisonment

under provisions of environmental legislation.

RECOMMENDED GROUNDING METHOD

The refrigerator should always be plugged into its own

individual properly grounded electrical outlet rated for

115 Volts, 60 Hz, AC only, and fused at 15 or 20 amperes.

This provides the best performance and also prevents

overloading house wiring circuits which could cause a fire

hazard from overheated wires. It is recommended the use

of a separate circuit serving only for this appliance, as well

as the use of a receptacle which cannot be turned off with

a switch or pull chain. Do not use an extension cord.

BEFORE YOU THROW AWAY

YOUR OLD REFRIGERATOR

OR FREEZER

Take off the doors.

Leave the shelves in place so that

children may not easily climb inside.

CAUTION

This appliance is not intended for use by persons (including children) with reduce physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the

appliance by person responsible for their safety.

Children should be supervised to ensure that they do not play with the

appliance.

For take back, please contact with the local agency.

Use this section to become more familiar with the parts and features.

NOTE:This guide covers several different models. The refrigerator you have purchased may have some

or all of the items listed below.The locations of the features shown below may not match your model.

PARTS AND FEATURES

*On some models

Digital Sensor Control

Filter (Inside)*

Durabase

Divider

Egg Box*

Refrigerator Door Rack

Freezer Light

Pull out Drawer

Ice Bin

Optibin Crisper

Keeps fruits and vegetable fresh and crisper

Chef Fresh / Snack Pan

Can Dispenser*

Temperature Control*

Shelves

Refrigerator Light

Custom cube Icemaker

Dairy Bin

REFRIGERATOR INSTALLATION

UNPACKING YOUR REFRIGERATOR

Remove tape and any temporary labels from your

refrigerator before using. Do not remove any warning-

type labels, the model and serial number label, or the

TechSheet that is attached to back wall of the refrigerator.

To remove any remaining tape or glue, rub the area

briskly with your thumb. Tape or glue residue can also be

easily removed by rubbing a small amount of liquid dish

soap over the adhesive with your fingers. Wipe with warm

water and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see the Important Safety Instructions

section.

Refrigerator shelves are installed in the shipping position.

Please reinstall shelves according to your individual

storage needs.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the

refrigerator for cleaning or service, be sure to protect

the floor. Always pull the refrigerator straight out when

moving it. Do not wiggle or walk the refrigerator when

trying to move it, as floor damage could occur.

INSTALLATION

1. Avoid placing the unit near heat sources, direct sunlight,

or moisture.

2. To avoid vibration, the unit must be level. If required,

adjust the leveling screws to compensate for

unevenness of the floor. The front should be slightly

higher than the rear to aid in door closing. Leveling

screws can be turned easily by tipping the cabinet

slightly. Turn the leveling screws clockwise ( ) to

raise the unit, counterclockwise ( ) to lower it.

3. Install this appliance in an area where the temperature

is between 55 °F (13 °C) and 110 °F (43 °C). If the

temperature around the appliance is too low or high,

cooling ability may be adversely affected.

1. Clean your refrigerator throughly and wipe off all dust

accumulated during shipping.

2. Install accessories such as ice cube bin, drawers,

shelves, etc., in their proper places. They are packed

together to prevent possible damage during shipment.

3. Let your refrigerator run for 2 or 3 hours before putting

food in it. Check the flow of cold air in the freezer

compartment to ensure proper cooling. Your refrigerator

is now ready for use.

WARNING:

Be careful when you work with hinge, base grille,

stopper, etc. You may be injured.

Do not put hands or metal sticks into air vents, base

grille, or bottom of refrigerator. You may be injured or

receive an electrical shock.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

WARNING

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion or fire.

CAUTION: Avoid placing the unit near heat sources,

direct sunlight or moisture.

Explosion Hazard

A proper distance from adjacent items

Please keep the refrigerator at a proper distance from other

things. Too small a distance from adjacent items may result

in lowered freezing capability and increased electricity

charge consumption.

2”

(5.08 cm)

BASE GRILLE INSTALLATION

To remove the base grille

To install or replace Base Grille:

1. Remove the 2 screws from the bottom front part of

refrigerator.

2. Place Base Grille into position and insert and tighten

screws.

1. Remove screws from Base Grille

and remove.

2. Reattach screws to the base of refrigerator.

REFRIGERATOR INSTALLATION

T O O L S Y O U M A Y N E E D

To move refrigerator through a house door, it maybe necessary to remove refrigerator and freezer door handles.

NOTE: Handle appearance may vary from illustrations on this page.

”

Hex head socket wrench

Phillips screwdriver

Flat head screwdriver

Allen wrench

10 mm

1/4 in

3/8 in

1/4 in

3/32 in

Mounting

Fasteners

Allen Wrench

Set Screw

1.Removing Refrigerator Handle

• Loosen the set screws with the 3/32 ” Allen

wrench and remove the handle.

NOTE: If the handle mounting fasteners

need to be tightened or removed, use a 1/4 ”

Allen wrench.

2.Removing Freezer Drawer Handle

• Loosen the set screws located on the lower

side of the handle with the 3/32 ” Allen

wrench and remove the handle.

NOTE: If the handle mounting fasteners

need to be tightened or removed, use a 1/4”

Allen wrench.

HOW TO REMOVE REFRIGERATOR HANDLE

REFRIGERATOR INSTALLATION

HOW TO REMOVE REFRIGERATOR DOOR (models without water dispenser)

1.Removing Refrigerator Door

NOTE: Handle appearance may vary.

IMPORTANT: Before you begin, turn the refrigerator OFF and unplug it. Remove food and any bins from doors.

Figure A

333

Left Door

Loosen the cover screw (1).

Disconnect door switch wire (2).

Loosen hinge bolts (3).

Lift off the top hinge (4).

Place the door on a non-scratching surface with the inside up.

Right Door

When removing top hinge, be careful that the door does not fall forward.

Loosen the cover screw (1).

Disconnect door switch wire (2).

Loosen hinge bolts (3).

Lift off the top hinge (4).

Place the door on a non-scratching surface with the inside up.

Loosen ground screw (6).

Disconnect wire harness (5).

(3)

(1)

(4)

(1)

(2)

(3)

(4)

(5)

(2)

(6)

CAUTION:

REFRIGERATOR INSTALLATION

2.Replacing Refrigerator Door

Right Door

Lower the door onto the middle hinge pin (7).

Make sure the door is aligned with the cabinet.

Replace the top hinge (4) installing hinge

screws (3) to secure it.

Make sure the gasket on the door is flush

against the cabinet and is not folded.

Support the door on the handle side while

securing. And make sure the door is straight

and the gap between the doors is even across

the front.

Install the ground screw (6).

Connect the door switch wire (2).

Tighten the cover screw (1).

Left Door

Lower the door into the middle hinge pin (5).

Make sure the door is aligned with the cabinet.

Replace the top hinge (4) installing hinge

screws (3) to secure it.

Make sure the gasket on the door is flush

against the cabinet and is not folded.

Support the door on the handle side while

securing. And make sure the door is straight

and the gap between the doors is even across

the front.

Connect the door switch wire (2).

Tighten the cover screw (1).

NOTE: The previous image to use as reference.

Figure A

333

REMOVING AND REPLACING REFRIGERATOR DOORS (models with water dispenser)

1.Removing Refrigerator Door

NOTE: Handle appearance may vary.

IMPORTANT: Before you begin, turn the refrigerator OFF and unplug it. Remove food and any bins from doors.

REFRIGERATOR INSTALLATION

(6)

(1)

(7)

(1)

(2)

(6)

(7)

(4)

(2)

(8)

Left Door

Disconnect water supply tube by pushing back on the disconnect ring (3).

Loosen the screws and remove the cover on back side (see figure A).

Loosen the cover screw (1).

Disconnect door switch wire (2).

Pull out the tube (4).

CAUTION: If a tube end is deformed or worn out, cut the damaged portion away.

Disconnect wire harness (5).

Loosen screws (6) and lift off the top hinge (7).

Place the door on a non-scratching surface with the inside up.

CAUTION: When removing top hinge, be careful that the door does not fall forward.

Right Door

Loosen the cover screw (1).

Disconnect door switch wire (2).

Disconnect wire harness (4).

Remove the ground screw (8).

Loosen screws (6) and lift off the top hinge (7).

Place the door on a non-scratching surface with the inside up.

(5)

(4)

2.Replacing Refrigerator Door

Right Door

Lower the door onto the middle hinge pin (9). Make sure the door is aligned with the cabinet.

Replace the top hinge (7) installing hinge screws (6) to secure it.

Make sure the gasket on the door is flush against the cabinet and is not folded. Support the door on the handle side while

securing hinge. Make sure the door is straight and the gap between the doors is even.

Install the ground screw (8) and connect the wire harness (4).

Connect the door switch wire (2).

Tighten the cover screw (1).

Left Door

Lower the door onto the middle hinge pin(8). Make sure the door is aligned with the cabinet.

Replace the top hinge (7) installing hinge screws (6) to secure it.

Make sure the gasket on the door is flush against the cabinet and is not folded. Support the door on the handle side while

tightening. And make sure the door is straight and the gap between the doors is even.

Insert the water supply tube (4) into the connector tube until you see only one scale mark.

(Fully insert the tube over 5/8”(15mm)).

Connect the wire harness (5).

Connect the door switch wire (2).

Tighten the cover screw (1).

REFRIGERATOR INSTALLATION

Connecting tube color

Blue to Blue

White to White

•

REFRIGERATOR INSTALLATION

CAUTION: When you remove the drawer, do not hold

handle. If it comes off, it could cause personal injury.

CAUTION: When laying down the drawer, be careful

not to damage the floor or hurt your feet by the sharp

edges on hinge side.

HOW TO REMOVE AND INSTALL THE

PULL OUT DRAWER

IMPORTANT: To avoid possible injury, product or property

damage, you will need two people to perform the following

instructions.

1.Removing Pull out Drawer

• Pull the drawer open to full lower extension. Remove the

lower basket (1) by lifting basket from rail system.

• Press both hangers with yours thumbs to lift it up.

• Separate the left and right rail cover.

• Remove the screws(2) of the rail on both sides.

• With both hands, hold both sides of the door and pull it

up to separate it from the rails.

• With both hands, hold the center of the bar and push it

in to let both rails fitted simultaneously.

HOW TO REMOVE AND INSTALL THE

PULL OUT DRAWER

IMPORTANT: To avoid possible injuyr or product or property

damage, you will need two people to perform the following

instructions.

2.Installing Pull out Drawer

• With both hands, hold the center of the bar and pull it

out to let both rails out to full extension simultaneously.

• Hook door supports (1) into rail tabes (2).

• Lower door into final position and tighten the screws (3).

• Make sure you have a right rail cover for each side.

• Align the top holes of the rail cover with the top holes of

the door supports to assemble the rail cover.

• With the drawer pulled out to full extension, insert the

lower basket (4) in the rail assembly.

WARNING: To prevent accidental child and pet

entrapment or suffocation risk. DO NOT allow them to

play inside of drawer.

WARNING: DO NOT step or sit down on Freezer Door.

Assembly hole

Right

Rail cover

Left

Rail cover

REFRIGERATOR INSTALLATION

LEVELING AND DOOR ALIGNMENT

Leveling

Your refrigerator has two front leveling screws, one on

the right and one on the left. If your refrigerator seems

unsteady or you want the doors to close easier, adjust the

refrigerator’ s tilt using the instructions below:

1. Plug the refrigerator’s power cord into a 3-prong

grounded outlet. Move the refrigerator into its final

position.

2. Turn the leveling screw clockwise to raise that side of

the refrigerator or counterclockwise to lower it. It may

take several turns of the leveling screw to adjust the tilt

of the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws.

This makes it easier to adjust the screws.

3. Open both doors again and check to make sure that

they close easily. If not, tilt the refrigerator slightly more

to the rear by turning both leveling screws clockwise. It

may take several more turns, and you should turn both

leveling screws the same amount.

4. Re-adjust if necessary.

5. Replace the base cover.

NOTE: Your new refrigerator is uniquely designed with

two fresh food doors. Either door can be opened or

closed independently of one another. You may have to

exert slight pressure on doors to get them to close

completely.

Door Alignment

If the space between your doors is uneven, follow the

instructions below to align the doors:

1. With one hand, lift up the door you want to raise at

middle hinge.

2. With other hand, use pliers to insert snap ring as

shown.

3. Insert additional snap rings until the doors are aligned.

(Three snap rings are provided with unit.)

REFRIGERATOR INSTALLATION

ENSURING PROPER AIR CIRCULATION

In order to ensure proper temperatures, air must flow

between the refrigerator and freezer sections. As shown in

the illustration below, air enters at top of freezer and

circulates down. From bottom of freezer, air is forced up to

top of refrigerator. Air enters refrigerator through top vent,

then circulates and exits at bottom, where it returns to

freezer.

MULTI-FLOW

Multi-Flow means powerful and effective cooling operation.

This is especially noticeable when new food is placed in the

refrigerator compartment.

If water or foreign substances enter the cool air vent while

cleaning, efficiency will be lowered. In addition, if gasket is

damaged, efficiency may be lowered because of escaping

cool air.

Do not block any of cool air vents with food packages. If

the vents are blocked, airflow will be interrupted and

temperature and moisture problems may occur.

IMPORTANT: Because air circulates between both sections,

sections, any odors formed in one section will transfer to the

other. You must thoroughly clean both sections to eliminate

odors. To prevent odor transfer and drying out of food, wrap

or cover foods tightly . (See the Food Storage Guide section

for details).

SETTING THE CONTROLS

Your refrigerator has two controls that let you regulate the

temperature in the freezer and refrigerator compartments.

Initially set the REFRIGERATOR CONTROL at 37 °F (3 °C)

and the FREEZER CONTROL at 0 °F (-18 °C). Leave it at

this setting for 24 hours (one day) to stabilize. Then adjust

the compartment temperature as desired.

Refrigerator control: 33 °

F to 46

F (0 ° C to 8 °C)

The lower the number setting, the colder the refrigerator

compartment will become.

Freezer control: -6 °F/ 8 °F (-21 °C to -13 °C)

When the setting is at a lower number, the freezer

compartment becomes colder.

Ice Plus:

Press the Ice Plus key and the LED will turn on. This

function will remain activated for 24 hours and intensify the

cooling speed of freezer and increase the amount of ice.

NOTE: If you want to change °F to °C, press and hold

COLDER key of freezer and COLDER key of refrigerator

over 3 sec at the same time. And if you want to change

°C

to °

F, hold them for 3 sec again.

REFRIGERATOR TEMP

COLDER WARMER 37 F IS RECOMMENDED

0 F IS RECOMMENDED

FREEZER TEMP

COLDER WARMER

(Models without water dispenser)

DOOR ALARM

With this feature you will listen an alarm when the freezer

or refrigerator door is not closed within 1 minute after it is

opened. These tones repeat every 30 seconds. The alarm

is cancelled when the freezer or the refrigerator is closed

correctly.

ICE PLUS

Identify your control Type

REFRIGERATOR INSTALLATION

ADJUSTING CONTROL SETTINGS

Give the refrigerator time to cool down completely before

adding food. It is best to wait 24 hours before you put food

into the refrigerator. The mid-settings indicated in the

previous section should be correct for normal household

refrigerator usage. The controls are set correctly when milk

or juice is as cold as you like and when ice cream is firm.

The refrigerator control functions as the thermostat for the

entire appliance (refrigerator and freezer sections.) The

higher the number setting, the longer the compressor will

run to keep the temperature colder. The freezer control

adjusts the cold air flow from the freezer to the refrigerator.

Setting the freezer control to a lower temperature keeps

more cold air in the Freezer compartment to make it colder.

If you need to adjust temperatures in the refrigerator or

freezer, start by adjusting the refrigerator first. Wait 24

hours after the refrigerator adjustment to check the freezer

temperature. If it is too warm or too cold, then adjust the

freezer control as well.

Use the settings listed in the chart below as a guide. Always

remember to wait at least 24 hours between adjustments.

RECOMMENDED

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR section

Turn

too warm

Door opened often

control to next

Large amount of food added

higher number,

Room temperature very warm

wait 24 hours,

Then re-check

FREEZER section too warm/ Turn FREEZER

ice not made fast enough control to next

Door opened often

higher number,

Large amount of food added

wait 24 hours,

Very cold room temperature Then re-check

(Can not cycle often enough)

Heavy ice usage

Air vents blocked by items

Move items out of

air stream

REFRIGERATOR section too

Turn

Cold

Controls not set correctly for

control to next

your conditions

lower number,

wait 24 hours,

then re-check

FREEZER section too cold Turn FREEZER

Controls not set correctly for

Control to next

your conditions

lower number,

wait 24 hours,

then re-check

SETTING THE CONTROLS

• Your refrigerator has a control pad on the dispenser that

lets you regulate the temperature in the freezer and

refrigerator compartments.

• Initially set the REFRIGERATOR CONTROL at 37 °F (3 °C)

and the FREEZER CONTROL at 0 °F (–18 °C). Leave it at

this setting for 24 hours (one day) to stabilize. Then adjust

adjust the compartment temperature as desired.

• Refrigerator Temp Control: 33 °F to 46 °F (0 °C to 8 °C)

The lower the number setting, the colder the refrigerator

compartment will become.

• Freezer Temp Control: -6 °F to 8 °F (-21 °C to -13 °C)

When the setting is at a lower number, the freezer

compartment becomes colder. The refrigerator

compartment becomes warmer because less cold air

flows into the refrigerator.

NOTE: If you want to change °F to °C or the reverse, press

and hold FREEZER key and REFRIGERATOR key

simultaneously for 5 seconds or more.

NOTE: Touch display once to activate, then touch again to

change the settings or activate a function. If 10 seconds

have passed since the display has been touched, it will be

necessary to touch “once” again to reactivate.

This is to prevent accidental display setting changes.

• Ice Plus: Press the ICE PLUS button and the LED will

turn on. This function will remain activated for 24 hours

and increase the cooling speed of the freezer and the

amount of ice produced.

• Dispenser Lock: Press and hold the LOCK button for 3

seconds to lock the dispenser When it is locked, the.

dispenser will not operate. To unlock, press and hold the

LOCK button for 3 seconds.

REFRIGERATOR

IMPORTANT: Wipe out moisture before using the display

button as operation of the button is based on touch sensing

method and becomes slow or other buttons may operate if

moisture is stuck to the surface of the button.

• Filter Reset: It displays in months the number of months

left to exchange the filter from the moment power is

connected to the refrigerator. If you have changed the

filter after 6 months of use, press and hold the FILTER

button 3 seconds or more and the filter display will be

initialized with a buzzing sound.

NOTE

: The average life of the filter is 6 months.

WARNING: If a door is open, the dispenser does not

REFRIGERATOR INSTALLATION

work.

• Display OFF Mode: To activate this mode press and hold

ICE PLUS and FREEZER key over 5 seconds until the

lights turn off. If the Display is touched or any door opens

the lights will turn on and after 20 seconds of inactivity the

lights will turn off automatically.

To exit Display OFF Mode press and hold ICE PLUS and

PLUS and FREEZER key over 5 seconds until the lights

tilt. Display Energy Save Mode does not affect the

temperature control settings of the unit.

(Models with water dispenser)

FOOD STORAGE GUIDE

Storing Fresh Food

Wrap or store food in the refrigerator in airtight and

moisture-proof material unless otherwise noted. This

prevents food odor and taste transfer throughout the

refrigerator. For dated products, check date code to

ensure freshness.

Butter or margarine

Keep opened butter in a covered dish or closed

compartment. When storing an extra supply, wrap

in freezer packaging and freeze.

Cheese

Store in the original wrapping until you are ready to

use it. Once opened, rewrap tightly in plastic wrap or

aluminum foil.

Milk

Wipe milk cartons. For best storage, place milk on interior

shelf, not on door shelf.

Eggs

Store in original carton on interior shelf, not on door shelf.

Fruit

Wash, let dry, and store in refrigerator in plastic bags or in

the crisper. Do not wash or hull berries until you are ready

to use them. Sort and keep berries in their original

container in a crisper, or store in a loosely closed paper

bag on a refrigerator shelf.

Leafy vegetables

Remove store wrapping and trim or tear off bruised and

discolored areas. Wash in cold water and drain. Place in a

plastic bag or plastic container and store in the crisper.

Vegetables with skins (carrots, peppers)

Place in plastic bags or plastic container and store

in crisper.

Fish

Chef fresh

Store most chef fresh in original wrapping as long as it is

airtight and moisture-proof. Rewrap if necessary.

Leftovers

Cover leftovers with plastic wrap or aluminum foil. Plastic

containers with tight lids can also be used.

STORING FROZEN FOOD

NOTE: For further information about preparing food for

freezing or food storage times, check a freezer guide or a

reliable cook book.

Packaging

Successful freezing depends on correct packaging. When

you close and seal the package, it must not allow air or

moisture in or out. If you do, you could have food odor

and taste transfer throughout the refrigerator and also dry

out frozen food.

Packaging recommendations:

Rigid plastic containers with tight-fitting lids

Straight-sided canning/freezing jars

Heavy-duty aluminum foil

Plastic-coated paper

Non-permeable plastic wraps

Specified freezer-grade self-sealing plastic bags

Follow package or container instructions for proper

freezing methods.

Do not use:

Bread wrappers

Non-polyethylene plastic containers

Containers without tight lids

Wax paper or wax-coated freezer wrap

Thin, semi-permeable wrap

Freezing

Your freezer will not quick-freeze any large quantity of

food. Do not put more unfrozen food into the freezer than

will freeze within 24 hours (no more than 2 to 3 lbs of food

per cubic foot of freezer space). Leave enough space in

the freezer for air to circulate around packages. Be careful

to leave enough room at the front so the door can close

tightly.

Storage times will vary according to the quality and type

of food, the type of packaging or wrap used (airtight and

moisture-proof) and the storage temperature. Ice crystals

inside a sealed package are normal. This simply means

that moisture in the food and air inside the package have

condensed, creating ice crystals.

NOTE: Allow hot foods to cool at room temperature for

30 minutes, then package and freeze. Cooling hot foods

before freezing saves energy.

NOTE: Do not store food near the sensor; it may cause

the sensor to malfunction.

USING YOUR REFRIGERATOR

WARNING

Suffocation Hazard

When using dry ice, provide adequate ventilation.

Dry ice is frozen carbon dioxide

(CO )

. When it

vaporizes, it can displace oxygen, causing dizziness,

light-headedness, unconsciousness and death by

suffocation. Open a window and do not breathe

the vapors.

Use fresh fish and shellfish the same day purchased.

IMPORTANT: Do not store bottles in the freezer

compartment - they may break when frozen,

causing damage.

REFRIGERATOR SHELVES

The shelves in your refrigerator are adjustable to meet

your individual storage needs. These units are all glass

shelves.

Storing similar food items together in your refrigerator and

adjusting the shelves to fit different heights of items will

make finding the exact item you want easier; it will also

reduce the amount of time the refrigerator door is open,

saving energy.

IMPORTANT: Do not clean glass shelves with warm

water when they are cold. Shelves may break if exposed

to sudden temperature changes or impact, such as

bumping. For your protection, glass shelves are made

with tempered glass, which will shatter into small pebble-

sized pieces.

NOTE: Glass shelves are heavy. Use special care when

removing them to avoid dropping them.

Adjusting Shelves

Remove shelves from the shipping position and replace

shelves in the position you want.

To remove a shelf: Tilt up the front of the shelf in the

direction of (1) and lift it in the direction of (2). Pull the

shelf out.

To replace a shelf: Tilt the front of the shelf up and guide

the shelf hooks into the slots at a desired height. Then

lower the front of the shelf so that the hooks drop into the

slots.

NOTE: Make sure that shelves are level from one side to

the other. Failure to do so may result in the shelf falling or

spilling food.

Sliding Out Shelves (optional on some models)

You can slide some glass shelves in and out of your

refrigerator as follows.

To slide the shelf out, carefully pull front of shelf

toward you.

To slide shelf in, push shelf in until it stops.

To remove a sliding shelf from its metal frame:

1. Pull the shelf out to the stop position.

2. Tilt the front of the shelf up and pull it past the stop

3. Lift up the shelf to remove.

Replace the shelf by reversing the above steps.

Convenience Shelves (optional on some models)

Folding Shelf: You can store taller items such as gallon

containers or bottles by simply sliding the shelf back.

REFRIGERATOR SECTION

USING YOUR REFRIGERATOR

position.

La page est en cours de chargement...

LG LFD23860ST Le manuel du propriétaire

Marque: LG

Modèle: LFD23860ST

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

LFD23860SW

Télécharger le PDF

rapport

dans d''autres langues

English: LG LFD23860ST Owner's manual

LG LFD23860ST Le manuel du propriétaire

Ce manuel convient également à

LG LFD23860ST Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents