LG WM2140CW Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire
OWNER’S MANUAL
WASHING MACHINE
WM2140C*
Please read this manual carefully before operating
your washing machine and retain it for future reference.
P/NO : MFL62526863
www.lg.com
ENGLISH
ESPAÑOL
FRANÇAIS
MFL62526863_en_100909.indd 1 9/9/10 4:52:13 PM
Congratulations on your purchase
and welcome to the LG family.
Your new LG washing machine
combines the most advanced
washing technology with simple
operation and high efficiency.
By following the operating and care
instructions in this manual, your
washer will provide you with many
years of reliable service.
THANK YOU!
INTRODUCTION
WARRANTY ................................................... 33
IMPORTANT SAFETY INSTRUCTIONS
Basic Safety Precautions ..................................... 4
Grounding Instructions .......................................... 4
Safety Instructions for Installation .......................... 5
Safety Instructions for Use, Care and Cleaning, and
and Disposal .......................................................... 6
PARTS AND FEATURES
Special Features ..................................................... 7
Key Parts and Components ................................... 8
INSTALLATION INSTRUCTIONS
Choose the Proper Location .................................. 9
Clearances ............................................................. 9
Flooring ................................................................ 10
Installations with Optional Pedestal Base
or Stacking Kit ...................................................... 10
Unpacking and Removing Shipping Bolts ........... 11
Connecting the Water Lines ................................. 12
Connecting the Drain Line .................................... 13
Leveling the Washer ............................................. 14
Installation of Non-skid pads (Optional) ............... 14
HOW TO USE
Control Panel Features ........................................ 1 5
Operating the Washer .......................................... 16
Cycle Guide .......................................................... 17
Sorting Wash Loads ............................................ 18
Selecting Detergent .............................................. 19
About the Dispenser ............................................. 19
Loading the Dispenser ......................................... 20
The Time and Status Display ............................... 21
Cycle Setting Buttons .......................................... 22
Cycle Options Buttons ......................................... 23
Special Funcctions ............................................... 24
CARE AND CLEANING
Regular Cleaning .................................................. 25
Cleaning the Washer ............................................ 26
Maintenance ......................................................... 27
TROUBLESHOOTING
Normal Sounds You May Hear ............................. 29
Before Calling for Service ..................................... 29
Using SmartDiagnosis™ ...................................... 32
SPECIFICATIONS/
OPTIONAL ACCESSORIES
Key Dimensions and Specifications ..................... 32
Optional Accessories ........................................... 32
Product Registration Information
Model:
Serial Number:
Date of Purchase:
The model and serial number can be located on the
rating plate on the front of the washer.
Staple your receipt here for your convenience in the
event you need it for warranty coverage.
2
MFL62526863_en_100909.indd 2 9/9/10 4:52:13 PM
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
3
wWARNING For your safety, the information in this manual must be
followed to minimize the risk of fire or explosion, electric shock, or to prevent
property damage, personal injury, or loss of life.
Your Safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read
and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER or WARNING.
These words mean:
wDANGER: You can be killed or seriously injured if you don’t immediately follow instructions.
wWARNING: You can be killed or seriously injured if you don’t follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of
injury, and tell you what can happen if the instructions are not followed.
READ ALL INSTRUCTIONS BEFORE USE
MFL62526863_en_100909.indd 3 9/9/10 4:52:14 PM
wWARNING For your safety, the information in this manual must be
followed to minimize the risk of fire or explosion, electric shock, or to prevent
property damage, personal injury, or loss of life.
READ ALL INSTRUCTIONS BEFORE USE
IMPORTANT SAFETY INSTRUCTIONS
Before use, the washer must be properly installed as
described in this manual.
Do not wash articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry cleaning solvents, or other flammable or
explosive substances, as they give off vapors that could
ignite or explode.
Do not add gasoline, dry cleaning solvents, or other
flammable or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE.
If the hot water system has not been used for such a
period, before using the washer, turn on all hot water
faucets and let the water flow from each for several
minutes. This will release any accumulated hydrogen
gas. As the gas is flammable, do not smoke or use an
open flame during this time.
Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is
used near children.
Before the washer is removed from service or
discarded, remove the door to prevent children from
climbing inside.
Do not install or store the washer where it will be
exposed to the weather or freezing temperatures.
Do not tamper with controls.
Do not repair or replace any part of the washer or
attempt any servicing other than as described in this
manual. We strongly recommend that any service be
performed by a qualified individual.
See Installation Instructions for grounding
requirements.
ALWAYS follow the fabric care instructions
supplied by the garment manufacturer.
Do not place items exposed to cooking oil in your
washer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a
load to catch fire.
Use fabric softeners or products to eliminate static only
as recommended by the manufacturer.
This washer is not designed for maritime use or for
mobile installations such as in RVs, aircraft, etc.
Turn off the water taps and unplug the washer if the
machine is to be left for an extended period of time,
such as during vacations.
Do not use to dry articles containing foam rubber or
similarly textured rubber-like materials.
Packaging material can be dangerous for children.
There is a risk of suffocation! Keep all packaging from
children.
Always check the inside of the washer for foreign
objects before loading laundry. Keep the door closed
when not in use.
Do not reach into the appliance if the tub or
agitator is moving.
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this
appliance, follow basic precautions, including the following.
BASIC SAFETY PRECAUTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of least resistance for electric current. This appliance is
equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must
be plugged into an appropriate outlet that is properly installed and grounded in accordance with all
local codes and ordinances.
GROUNDING INSTRUCTIONS
wWARNING: Improper connection of the equipment-grounding conductor can result in risk
of electric shock. Check with a qualified electrician or servicer if you are in doubt as to whether the appli-
ance is properly grounded. Do not modify the plug provided with the appliance. If it does not fit the
outlet, have a proper outlet installed by a qualified electrician. Failure to follow these warnings can cause
serious injury, fire, electrical shock, or death.
4
MFL62526863_en_100909.indd 4 9/9/10 4:52:14 PM
ENGLISH
Refer to INSTALLATION INSTRUCTIONS for
detailed grounding procedures. Installation
instructions are packed with the washer for installer’s
reference. If the washer is moved to a new location,
have it checked and reinstalled by a qualified service
person. Failure to follow this warning can cause
serious injury, fire, electrical shock, or death.
Do not, under any circumstances cut or remove
the third (ground) prong from the power cord.
Failure to follow this warning can cause serious
injury, fire, electrical shock, or death.
For personal safety, this appliance must be
properly grounded. Failure to follow this warning
can cause serious injury, fire, electrical shock,
or death.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric shock from this
appliance.
This washer must be plugged into a 120 VAC,
60 Hz grounded outlet. Failure to follow this warning
can cause serious injury, fire, electrical shock, or
death.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded. Failure to follow this warning
can cause serious injury, fire, electrical shock,
or death.
Where a standard 2-prong wall outlet is
encountered, it is your personal responsibility
and obligation to have it replaced with a properly
grounded 3-prong wall outlet. Failure to follow
this warning can cause serious injury, fire, electrical
shock, or death.
Do not install on carpet. Install washer on a solid
floor. Failure to follow this warning can cause serious
leak damage.
Do not remove ground prong. Do not use an
adapter or extension cord. Plug into a grounded
3-prong outlet. Failure to follow these warnings can
cause serious injury, fire, electrical shock, or death.
The washer should always be plugged into its
own individual electrical outlet which has a
voltage rating that matches the rating plate. This
provides the best performance and also prevents
overloading house wiring circuits which could cause
a fire hazard from overheated wires.
Never unplug your washer by pulling on the
power cord. Always grip plug firmly and pull straight
out from the outlet. Failure to follow this warning can
cause serious injury, fire, electrical shock, or death.
Repair or replace immediately all power cords
that have become frayed or otherwise damaged.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end. Failure
to follow this warning can cause serious injury, fire,
electrical shock, or death.
When installing or moving the washer, be careful
not to pinch, crush, or damage the power cord.
Failure to follow this warning can cause serious
injury, fire, electrical shock, or death.
The washer must be installed and electrically
grounded by a qualified service person in
accordance with local codes to prevent shock
hazard and assure stability during operation.
The washer is heavy. Two or more people may be
needed to install and move the appliance. Failure
to do so can result in back or other injury.
Store and install the washer where it will not
be exposed to temperatures below freezing or
exposed to outdoor weather conditions. Failure to
follow this warning can cause serious leak damage.
Do not install the washer in humid spaces to
reduce the risk of electric shock. Failure to follow
this warning can cause serious injury, fire, electrical
shock, or death.
To reduce the risk of personal injury, adhere to
all industry recommended safety procedures
including the use of long sleeved gloves and
safety glasses. Failure to follow all of the safety
warnings in this manual could result in property
damage, personal injury or death.
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this
appliance, follow basic precautions, including the following.
SAFETY INSTRUCTIONS FOR INSTALLATION
wWARNING For your safety, the information in this manual must be
followed to minimize the risk of fire or explosion, electric shock, or to prevent
property damage, personal injury, or loss of life.
READ ALL INSTRUCTIONS BEFORE USE
IMPORTANT SAFETY INSTRUCTIONS
5
MFL62526863_en_100909.indd 5 9/9/10 4:52:14 PM
IMPORTANT SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS FOR USE, CARE AND CLEANING, AND DISPOSAL
Unplug the washer before cleaning to avoid the
risk of electric shock.
Never use harsh chemicals, abrasive cleaners,
or solvents to clean the washer. They will
damage the finish.
Do not put oily or greasy rags or clothing on
top of the washer. These substances give off
vapors that could ignite the materials.
Do not wash items that are soiled with
vegetable or cooking oil. These items may
contain some oil after laundering. Due to the
remaining oil, the fabric may smoke or catch
fire by itself.
Disconnect this appliance from the
power supply before attempting any user
maintenance. Turning the controls to the OFF
position does not disconnect this appliance
from the power supply. Failure to follow this
warning can cause serious injury, fire, electrical
shock, or death.
Do not combine laundry products for use
in one load unless specified on the label.
Do not mix chlorine bleach with ammonia
or acids such as vinegar. Follow package
directions when using laundry products.
Incorrect usage can produce poisonous gas,
resulting in serious injury or death.
Do not reach into the washer while parts are
moving. Before loading, unloading, or adding
items, press the START/PAUSE button and
allow the drum to coast to a complete stop
before reaching inside. Failure to follow this
warning can cause serious injury, fire, electrical
shock, or death.
Do not allow children to play on or in the
washer. Close supervision of children is
necessary when the washer is used near
children. As children grow, teach them the
proper, safe use of all appliances. Failure to
comply with these warnings could result in serious
personal injuries.
Destroy the carton, plastic bag, and other
packing materials after the washer is
unpacked. Children might use them for play.
Cartons covered with rugs, bedspreads, or
plastic sheets can become airtight chambers.
Failure to comply with these warnings could result
in serious personal injuries.
Keep laundry products out of children’s reach.
To prevent personal injury, observe all warnings
on product labels. Failure to comply with these
warnings could result in serious personal injuries.
Remove the door to the washing compartment
to avoid the danger of children or small animals
getting trapped inside before your washer is
removed from service or discarded. Failure to do
so can result in serious personal injury or death.
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this
appliance, follow basic precautions, including the following.
6
SAVE THESE INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
wWARNING
For your safety, the information in this manual must be
followed to minimize the risk of fire or explosion, electric shock, or to prevent
property damage, personal injury, or loss of life.
MFL62526863_en_100909.indd 6 9/9/10 4:52:14 PM
ENGLISH
PARTS AND FEATURES
SPECIAL FEATURES
C
B
A
D
E
DETERGENT DISPENSER DRAWER
This four-compartment drawer provides separate
dispensers for prewash and main wash detergent,
liquid bleach, and liquid fabric softener.
EASY-ACCESS LOCKING DOOR
Extra-large door locks during operation and
features a delay to prevent the door from being
opened until the washer interior has cooled and
the water level has lowered.
INVERTER DIRECT-DRIVE MOTOR
The inverter direct-drive motor eliminates the belt
and pulleys found on most washers to provide
improved performance and reliability while
increasing energy efficiency.
SMARTDIAGNOSIS™
Should you experience any technical difficulty
with your washing machine, it has the capability
of transmitting data by phone to the Customer
Information Center. The call center agent records
the data transmitted from your machine and
uses it to analyze the issue, providing a fast and
effective diagnosis. (Refer to page 32.)
MAGNETIC DOOR PLUNGER
Safely and conveniently secure the door slightly
ajar with a magnetic door plunger. This will
promote air circulation and allow the interior of
the machine to dry.
To use this feature, after the load has been
removed, do not close the door completely.
When the magnetic door plunger comes into
contact with the metal washer cabinet, it will
secure the door slightly open allowing the interior
of the washer to dry.
D
A
C
B
E
7
MFL62526863_en_100909.indd 7 9/9/10 4:52:15 PM
PARTS AND FEATURES
Hot and Cold
Water Inlets
Drain
Hose
Rear of Washer
KEY PARTS AND COMPONENTS
In addition to the special features and
components outlined in the Special Features
section, there are several other important
components that are referenced in this manual.
A
LARGE-CAPACITY STAINLESS STEEL DRUM
The large capacity stainless steel drum offers
extreme durability and is tilted to improve
efficiency and allow easier access for large items.
B
LED DISPLAY
The LED display shows the settings, estimated
time remaining, options, and status messages for
your washer. When the washer is turned on, the
light in the display will illuminate.
C
LEVELING FEET
Four leveling feet (two in the front and two in
the back) adjust to improve washer stability on
uneven floors.
D
DRAIN ACCESS PANEL
Provides access to the drain line and drain
pump filter.
B
A
D
Included Accessories
Hot and Cold
Water Hoses
Non-skid pads
Wrench (for removing
shipping bolts and
adjusting and
locking leveling feet)
Tie Strap
(for securing
drain hose)
Elbow Bracket
(for securing
drain hose)
Caps (4)
(for covering
shipping bolt holes)
C
8
MFL62526863_en_100909.indd 8 9/9/10 4:52:16 PM
ENGLISH
INSTALLATION INSTRUCTIONS
CHOOSE THE PROPER LOCATION
CLEARANCES
To ensure sufficient clearance for
water lines and airflow, allow minimum
clearances of at least 1 inch (2.5 cm) at
the sides and 4 inches (10 cm) behind
the unit. Be sure to allow for wall, door,
or floor moldings that may increase the
required clearances.
wWARNING
Washer is heavy! Two or more people
are required when moving and unpacking
the washer. Failure to do so can result in back
or other injury.
Store and install the washer where it will not
be exposed to temperatures below freezing
or exposed to outdoor weather conditions.
Failure to follow this warning can cause serious
injury, fire, electrical shock, or death.
Properly ground washer to conform with all
governing codes and ordinances. Failure to
follow this warning can cause serious injury, fire,
electrical shock, or death.
To reduce the risk of electric shock, do not
install the washer in humid spaces. Failure to
follow this warning can cause serious injury, fire,
electrical shock, or death.
The base opening must not be obstructed by
carpeting when the washer is installed on a
carpeted floor.
Do not remove ground prong. Do not use
an adapter or extension cord. Plug into a
grounded 3-prong outlet. Failure to follow this
warning can cause serious injury, fire, electrical
shock, or death.
Power Outlet
The power outlet must be within 60 inches
(1.5 m) of either side of the washer.
The appliance and outlet must be positioned so
that the plug is easily accessible.
Do not overload the outlet with more than one
appliance.
The outlet must be grounded in accordance with
current wiring codes and regulations.
Time-delay fuse or circuit breaker is
recommended.
NOTE: It is the personal responsibility and
obligation of the product owner to have a
proper outlet installed by a qualified electrician.
22
1
2
(57 cm)
29
3
4
(75.6 cm)
51”
(129.7 cm)
4”
(10 cm)
1”
(2.5 cm)
1”
(2.5 cm)
27”
(68.6 cm)
Allow at least 24 inches (61.2 cm) in
front of the washer to open the door.
9
MFL62526863_en_100909.indd 9 9/9/10 4:52:17 PM
INSTALLATION INSTRUCTIONS
FLOORING INSTALLATIONS WITH
OPTIONAL PEDESTAL BASE OR
STACKING KIT
To minimize noise and vibration, the washer
MUST be installed on a solidly constructed floor.
See the NOTE below.
Allowable slope under the entire washer is
1° maximum.
Carpeting and soft tile surfaces are not
recommended.
Never install the washer on a platform or weakly
supported structure. Use only an approved
accessory pedestal as described below.
NOTE: Please note that the floor must be strong
and rigid enough to support the weight of the
washer when fully loaded, without flexing or
bouncing. If your floor has too much flex in it,
you may need to reinforce it to make it more
rigid. A floor that is adequate for a top-loading
washer may not be rigid enough for a front-
loading washer, due to the difference in the spin
speed and direction. If the floor is not solid, your
washer may vibrate and you may hear and feel
the vibration throughout your house.
Required Dimensions for Installation
With Stacking Kit
IMPORTANT: If you are installing your washer
using an optional pedestal base or stacking
kit, please refer to Optional Accessories in this
manual or to the instructions for your pedestal
or stacking kit before proceeding with the
installation.
Required Dimensions for Installation
With Pedestal
29
3
4
(75.6 cm)
4”
(10 cm)
1”
(2.5 cm)
1”
(2.5 cm)
27”
(68.6 cm)
77
1
2
(196.8 cm)
NOTE: Before installing the
washer, make sure the floor is
clean, dry and free of dust, dirt,
water and oils so the washer feet
can not slide easily. Leveling feet
that can move or slide on the floor can contribute
to excess vibration and noise due to poor contact
with the floor.
NOTE: If a drip pan must
be used, take extra care
to follow the instructions
provided with the drip pan
and make sure the leveling
feet are adjusted for firm and even contact with
the pan. Use of drip pans and failure to properly
level the machine may result in increased vibration
and noise during operation.
10
MFL62526863_en_100909.indd 10 9/9/10 4:52:18 PM
ENGLISH
INSTALLATION INSTRUCTIONS
When removing the washer from the carton base,
be sure to remove the foam tub support in the
middle of the carton base.
If you must lay the washer down to remove the
base packaging materials, always lay it carefully
on its side. Do NOT lay the washer on its front or
back.
IMPORTANT:
To prevent internal damage during
transport, the washer is equipped with 4 shipping
bolts and plastic retainers. These bolts and
retainers MUST be removed before operating the
washer.
Failure to remove shipping bolts and retainers
may cause severe vibration and noise, which can
lead to permanent damage to the washer. The
cord is secured to the back of the washer with
a shipping bolt to help prevent operation with
shipping bolts in place.
Starting with the bottom 2 shipping bolts,
use the included wrench to remove the
4 shipping bolts by turning them
counterclockwise.
1
Shipping
Bolts
Remove the retainers by turning them slightly
while pulling. Rotate and press the hole caps
into the shipping bolt holes.
2
NOTE: Save the bolts and retainers for
future use. To prevent damage to internal
components, the shipping bolts and
retainers must be installed when
transporting the washer.
Retainer
Hole Cap
UNPACKING AND REMOVING SHIPPING BOLTS
Carton Base
Foam Tub
Support
11
MFL62526863_en_100909.indd 11 9/9/10 4:52:20 PM
INSTALLATION INSTRUCTIONS
CONNECTING THE WATER LINES
Check the rubber seals on both sides of the
hose.
- Insert a rubber seal into the threaded fittings
on each hose to prevent leaking.
1
Water hose
(To water inlet
on the washing
machine)
Rubber Seal
Water hose
(To tap)
Rubber Seal
3
Turn on the water tap to remove foreign
substance such as dirt, sand, or sawdust
in the water line, and then check the water
temperature.
4
Connect the hoses to the water inlets.
- Connect the blue hose to the cold water
inlet and the red hose to the hot water inlet.
Connect the water hoses to the faucets.
- Connect the blue hose to a cold water
faucet and the red hose to a hot water
faucet.
- If there is only one faucet, connect it to
the cold water faucet. In this case, the
water supply may be delayed for the
first 3 minutes of the supply in order to
differentiate hot from cold water.
2
Check for leaks by turning on the faucets.
- If water leaks, check steps 1 to 3 again.
NOTE
For your safety, and for extended product life,
use only authorized components.
The manufacturer is not responsible for product
malfunction or accidents caused by the use of
separately purchased unauthorized parts.
Use new hoses when you install the washing
machine. Do not reuse old hoses.
Periodically check the hoses for cracks, leaks
and wear, and replace the hoses every 5 years.
Do not stretch the water hoses intentionally, and
make sure that they are not crushed by other
objects.
Water line pressure must be between 14.5 PSI
and 116 PSI (100 - 800 kPa). If the water line
pressure is higher than 116 PSI, a pressure
reducing valve must be installed.
Cold
Water
Inlet
Hot
Water
Inlet
12
MFL62526863_en_100909.indd 12 9/9/10 4:52:21 PM
ENGLISH
INSTALLATION INSTRUCTIONS
CONNECTING THE DRAIN LINE
Insert the end of the drain hose into the floor
drain. Secure the hose in place to prevent it
from moving.
Option 3: Floor Drain
Clip the end of the hose into the elbow bracket.
Hang the end of the drain hose over the side of
the laundry tub. Use tie strap to secure the drain
hose in place.
NOTE: Total height of the hose end should not
exceed 96 inches (244.8 cm) from the bottom of
the washer.
Option 2: Laundry Tub
Laundry
Tub
Elbow
Bracket
Tie
Strap
Drain
Hose
The drain hose should always be properly
secured. Failure to properly secure the drain
hose can result in flooding and property
damage.
Do not install the end of the drain hose higher
than 96 inches (244.8 cm) above the bottom of
the washer.
The drain must be installed in accordance with
any applicable local codes and regulations.
Make sure that the water lines are not stretched,
pinched, crushed, or kinked.
NOTE: If the drain hose is extended more than
4 inches beyond the end of the elbow bracket,
mold or microorganisms could spread to
the inside of the washer.
Clip the end of the hose into the elbow bracket.
Insert the end of the drain hose into a standpipe.
Use tie strap to secure the drain hose in place.
NOTE: Total height of the hose end should not
exceed 96 inches (244.8 cm) from the bottom of
the washer.
Option 1: Standpipe
Drain Hose
Floor Drain
Stand
Pipe
Tie Strap
Elbow
Bracket
Drain
Hose
13
MFL62526863_en_100909.indd 13 9/9/10 4:52:25 PM
INSTALLATION INSTRUCTIONS
LEVELING THE WASHER
INSTALLATION OF NON-SKID
PADS (OPTIONAL)
Position the washer in the final location,
taking special care not to pinch, strain, or
crush the water and drain lines. Place a level
across the top of the washer.
1
Level
Leveling
Feet
Leveling
Feet
The drum of your new washer spins at very high
speeds, up to 1,100 RPM. To minimize vibration,
noise, and unwanted movement, the floor must
be a perfectly level, solid surface.
NOTE: Adjust the leveling feet only as far as
necessary to level the washer. Extending the
leveling feet more than necessary can cause
the washer to vibrate.
Some floor surfaces are too slippery to prevent
the washer from moving on the floor during
heavily unbalanced loads. While it is normal for
an occasional load to be out of balance, excess
noise and vibration can result from the washer
moving out of position. If these conditions are
encountered, follow the instructions below for
installation of the non-skid pads. These pads
will help prevent the washer from moving during
heavy out of balance conditions, thereby reducing
noise and vibration.
Loosen the locknuts on all 4 leveling feet
until you can turn the feet with the included
wrench. Turn clockwise to raise the washer
or counterclockwise to lower it.
2
Raise Lower
NOTE: To make sure that the washer is
properly level, run the washer with a test load:
Place approximately 6 pounds of laundry
in the machine. Then press POWER, select
RINSE+SPIN cycle, and then press the START/
PAUSE button. See the following sections for
additional information on cycle selection and
operation.
Verify that the washer does not rock or vibrate
excessively during the spin cycle.
If the washer vibrates or shakes, adjust
the leveling feet until the washer is stable and
retest.
3
Once the washer is level from side to side and
front to back, tighten all locknuts securely.
Make sure that all 4 leveling feet are in firm
contact with the floor.
Tighten all 4 lock
nuts securely using
the wrench.
All four leveling feet must rest solidly on the
floor. Rock the washer gently from corner to
corner to make sure that the washer does
not rock.
If you are installing the washer on the optional
pedestal, you must use the leveling feet on
the pedestal to level the washer. The washer’s
leveling feet should be fully retracted and locked
into position with the locknuts.
Non-skid pads
Place the pads under both front feet.
This side up
Stick adhesive side
to floor
Remove backing
14
MFL62526863_en_100909.indd 14 9/9/10 4:52:28 PM
ENGLISH
HOW TO USE
CONTROL PANEL FEATURES
POWER ON/OFF BUTTON
Press to turn the washer ON. Press again to
turn the washer OFF.
NOTE: Pressing the ON/OFF button during
a cycle will cancel that cycle and any load
settings will be lost.
CYCLE SELECTOR KNOB
Turn this knob to select the desired cycle.
Once the desired cycle has been selected,
the standard presets will be shown in the
display. These settings can be adjusted using
the cycle settings buttons anytime before
starting the cycle.
A
B
TIME AND STATUS
The display shows the selected settings
and options, as well as the estimated time
remaining in the cycle.
E
F
START/PAUSE BUTTON
Press this button to START the selected
cycle. If the washer is running, use this
button to PAUSE the cycle without losing the
current settings.
NOTE: If you do not press the START/PAUSE
button within 4 minutes of selecting a cycle,
the washer automatically turns off.
C
CYCLE SETTINGS BUTTONS
Use these buttons to adjust the desired cycle
options for the selected cycle.
D
OPTION BUTTON
The option buttons allow you to select
additional cycle options and will light when
selected. Certain buttons also allow you to
activate special functions by pressing and
holding the button for 3 seconds.
For detailed information about the individual
options, please see the following pages.
D
A
B
C
E
F
F
15
MFL62526863_en_100909.indd 15 9/9/10 4:52:29 PM
HOW TO USE
OPERATING THE WASHER
Press the ON/OFF button to turn on the
washer. The lights around the
cycle selector knob will illuminate.
Turn the cycle selector knob to the desired
cycle. The display will show the
preset Rinse/Wash Temperature,
Spin Speed, Soil Level, and
Option settings for that cycle.
If you would like to change the settings for
that cycle, press the appropriate cycle set-
ting button(s) until the indicator light for the
desired setting is lit.
NOTE: To protect your garments, not every
wash/rinse temperature, spin speed, soil
level, or option is available with every cycle.
A
B
C
Select any additional cycle options, such
as PRE-WASH, RINSE+SPIN,
QUICK CYCLE, STAIN CYCLE,
or TUB CLEAN, by pressing the
OPTION button until the desired
option is lit.
NOTE: To protect your garments,
not every wash/rinse temperature,
spin speed, soil level, or option is
available with every cycle.
D
Press the START/PAUSE button to begin
the cycle. The door will latch,
the display will change, and
the washer will calculate the
estimated time remaining. Once
the washer has calculated the estimated
total cycle time, the washer will start.
To pause the cycle at any time, press
START/PAUSE.
NOTE: The cycle time displayed may appear
much longer than that of a toploading
washer. The displayed time is for the
complete cycle, rather than just the agitation
portion of the cycle, as is typically shown on
a top-loading washer.
NOTE: If the temperature in the washer is
too high, the door cannot be unlocked until
the washer has cooled. If the water level is
too high, select the DRAIN & SPIN to drain
excess water. Do not try to force the door
open.
Washing time can be reduced significantly
for small or lightly soiled loads by selecting
the Speed Wash cycle and setting the Soil
Level button to Light.
E
Once you have loaded the washer and added
laundry products (detergent, bleach, and/or fabric
softener):
When the load is finished, the signal (if set)
will sound and the door will unlock.
Remove damp clothes from the washer
immediately. Check under the door seal for
small items.
F
16
MFL62526863_en_100909.indd 16 9/9/10 4:52:30 PM
ENGLISH
HOW TO USE
CYCLE GUIDE
The cycle guide below shows the options and recommended fabric types for each cycle.
= Available option
NOTE: To protect your garments, not every wash/rinse temperature, spin speed, soil level, or option is
available with every cycle.
CYCLE FABRIC TYPE
SPIN SPEED
SOIL LEVEL
EXTRA
RINSE
WATER
PLUS
STEAM
COLDWASH™
WASH/RINSE
OPTIMIZER
TM
STAIN
CARE
PRE-
WASH
WASH/RINSE
TEMP.
CYCLE FABRIC TYPE
SPIN SPEED SOIL LEVEL
QUICK
CYCLE
STAIN
CYCLE
EXTRA
RINSE
RINSE+
SPIN
WATER
PLUS
PRE-
WASH
WASH/RINSE
TEMP.
COTTON/
NORMAL
SPEED
WASH
DRAIN
+
SPIN
HAND WASH/
WOOL
Cotton, linen, towels,
shirts, sheets, jeans,
mixed loads
Lightly soiled clothing and
small loads
Drain, Spin Only
Items labeled
“hand-washable”
BULKY/
LARGE
PERM.
PRESS
DELICATES
Large items such as
blankets and comforters
Dress shirts/pants,
wrinkle-free clothing,
poly/cotton blend
clothing, tablecloths
Dress shirts/blouses,
nylons, sheer or lacy
garments
Warm/Cold
Medium
No Spin
Warm/Warm
Hot/Cold
Tap Cold/Cold
Cold/Cold
Heavy
Light
NormalLow
Warm/Cold
High
No Spin
Low
Warm/Warm
Hot/Cold
Tap Cold/Cold
Cold/Cold
Heavy
Light
NormalMedium
Cold/Cold
No Spin
Low
Warm/Cold
Warm/Warm
Tap Cold/Cold
Heavy
Light
NormalMedium
Warm/Cold
Extra High
No Spin
Low
Medium
Hot/Cold
Tap Cold/Cold
Cold/Cold
Heavy
Light
NormalHigh
Hot/Cold
No Spin
Low
Medium
High
Cold/Cold
Warm/Cold
Warm/Warm
Normal
Heavy
LightExtra High
-
Extra High
No Spin
Low
Medium
- -
-High
Warm/Cold
No Spin
Warm/Warm
Cold/Cold
Light
NormalLow
17
MFL62526863_en_100909.indd 17 9/9/10 4:52:31 PM
HOW TO USE
SORTING WASH LOADS
Fabric Care Labels
Most articles of clothing feature fabric care labels
that include instructions for proper care.
Fabric Care Labels
Grouping Similar Items
For best results, sort clothes into loads that can
be washed with the same wash cycle.
Different fabrics have different care requirements.
Always wash dark colors separately from light
colors and whites to prevent discoloration. If
possible, do not wash heavily soiled items with
lightly soiled ones. The chart below shows
recommended groupings.
Sort Laundry...
by Colors by Soil by Fabric by Lint
Whites Heavy Delicates Lint Producer
Lights Normal Easy Care Lint Collector
Darks Light Sturdy
Loading the Washer
Check all pockets to make sure that they are
empty. Items such as clips, matches, pens,
coins, and keys can damage both your washer
and your clothes.
Close zippers, hooks, and drawstrings to
prevent these items from snagging or tangling
on other clothes.
• Pre-treat heavily stained areas for best results.
Combine large and small items in a load. Load
large items first.
Large items should not be more than half of the
total wash load.
The drum should not be tightly packed with
items. The door of the washer should close
easily.
To prevent an out-of-balance load, do not wash
single items. Add one or two similar items to
the load. Large, bulky items, such as a blanket,
comforter, or bedspread should be washed
individually.
Do not wash or spin waterproof clothes.
When unloading the washer, check under the
door seal for small items.
NOTE: The front loading washer rotates the wet
laundry to wash it with less water. If you do not
see the water during washing, it is not a problem
because the laundry is sufficiently wet.
18
MFL62526863_en_100909.indd 18 9/9/10 4:52:32 PM
ENGLISH
HOW TO USE
SELECTING DETERGENT ABOUT THE DISPENSER
The automatic dispenser consists of four
compartments which hold:
• Liquid chlorine bleach.
• Liquid fabric softener.
• Liquid or powdered detergent for pre-wash.
Liquid or powdered detergent and color-safe
bleach for main wash.
All laundry products can be added at once in
their respective dispenser compartments. They
will be dispensed at the appropriate time for the
most effective cleaning.
After adding the laundry products to the
dispenser, close the dispenser drawer.
To add detergent, bleach, and fabric softener to
the automatic dispenser:
Open the dispenser drawer.
Load the laundry products into the
appropriate compartments.
Slowly close the dispenser drawer to
avoid early dispensing of the laundry
products.
NOTE: It is normal for a small amount of water to
remain in the dispenser compartments at the end
of the cycle.
1
2
3
Designed specially to use only
HE (High-Efficiency) detergent
IMPORTANT: Your washer is designed for
use with only High-Efficiency (HE) detergents.
HE detergents are formulated specifically for
front-load washers and contain suds-reducing
agents. Always look for the HE symbol when
purchasing detergent.
HE detergents produce fewer suds, dissolve
more efficiently to improve washing and rinsing
performance, and help to keep the interior of your
washer clean.
Using a regular detergent may cause excessive
sudsing and unsatisfactory performance.
IMPORTANT: Do not place or store laundry
products, such as detergent, bleach, or liquid
fabric softener, on top of your washer or dryer.
Wipe up any spills immediately. These products
can damage the finish and controls.
Liquid Chlorine
Bleach
Compartment
Liquid Fabric
Softener
Compartment
Pre-wash
Detergent
Compartment
Main Wash Detergent
Compartment
Liquid
Detergent
Cup
Insert
19
MFL62526863_en_100909.indd 19 9/9/10 4:52:33 PM
HOW TO USE
LOADING THE DISPENSER
Pre-wash Detergent Compartment
Add liquid or powdered detergent to this
compartment when using the pre-wash option.
Always use HE (High-Efficiency) detergent with
your washing machine.
The amount of detergent added for the
pre-wash
option is
1
2 the amount recommended for the
main wash cycle. For example, if the main wash
cycle requires one measure of detergent, add
1
2 measure for the pre-wash option.
NOTE: If liquid detergent is to be used for the
main wash when using the pre-wash option, the
liquid detergent cup accessory must be used
in the main wash dispenser to prevent the main
wash liquid detergent from being dispensed
immediately.
Main Wash Detergent Compartment
This compartment holds laundry detergent
for the main wash cycle, which is added to
the load at the beginning of the cycle. Always
use HE (High-Efficiency) detergent with your
washing machine.
Never exceed the manufacturer’s
recommendations when adding detergent.
Using too much detergent can result in
detergent buildup in clothing and the washer.
Either powdered or liquid detergent may be used.
When using liquid detergent, make sure the
liquid detergent cup and insert are in place.
Do not exceed the maximum fill line.
When using powdered detergent, remove
the insert and liquid detergent cup from the
compartment. Powdered detergent will not
dispense with the liquid detergent cup and
insert in place.
NOTE: Liquid or powdered color-safe bleach
may be added to the main wash compartment
with detergent of the same type.
Liquid Bleach Compartment
This compartment holds liquid chlorine bleach,
which will be dispensed automatically at the
proper time during the wash cycle.
Do not add powdered or liquid color-safe bleach
to this compartment.
Always follow the manufacturer’s
recommendations when adding bleach. Do not
exceed the maximum fill line. Using too much
bleach can damage fabrics.
Never pour undiluted liquid chlorine bleach
directly onto the load or into the drum. Fabric
damage can occur.
Fabric Softener Compartment
This compartment holds liquid fabric softener,
which will be automatically dispensed during the
final rinse cycle.
Always follow the manufacturer’s
recommendations when adding fabric softener.
Do not exceed the maximum fill line. Using
too much fabric softener may result in stained
clothes.
Dilute concentrated fabric softeners with warm
water. Do not exceed the maximum fill line.
Never pour fabric softener directly onto the load
or into the drum.
Designed specially to use only
HE (High-Efficiency) detergent
20
MFL62526863_en_100909.indd 20 9/9/10 4:52:33 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108

LG WM2140CW Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire