Kenmore 62332 Le manuel du propriétaire

Marque: Kenmore

Modèle: 62332

Catégorie: Sèche-linge électriques

Taper: Le manuel du propriétaire

Use & Care Guide

Manual de uso y cuidado

Guide d’Utilisation et d’Entretien

English / Español / Français

Table of Contents......2 / Índice......14 / Table des matières......26

Kenmore®

Electric or Gas Dryer

Secadora eléctrica o a gas

Sécheuse électrique ou à gaz

Models/Modelos/Modèles: 6012, 7012, C60122, 60222, 70222, C60222, C60242, 62332, 72332, C62332

P/N W10738930A

Sears Brands Management Corporation

Hoffman Estates, IL 60179 U.S.A.

www.kenmore.com

www.sears.com

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2C3

www.sears.ca

DRYER SAFETY

IMPORTANT: When discarding or storing your old clothes dryer, remove the door.

TABLE OF CONTENTS

DRYER SAFETY ........................................................................... 2

CHECK YOUR VENT SYSTEM FOR GOOD AIR FLOW .....4

USE AUTO DRY CYCLES FOR BETTER FABRIC CARE

AND ENERGY SAVINGS .......................................................... 4

CONTROL PANEL AND FEATURES ........................................ 5

CYCLE GUIDE ............................................................................. 6

USING YOUR DRYER ................................................................ 7

DRYER CARE ............................................................................... 9

TROUBLESHOOTING ................................................................ 11

PROTECTION AGREEMENTS` ................................................13

WARRANTY ...............................................................................13

ASSISTANCE OR SERVICE .....................................................40

CHECK YOUR VENT SYSTEM FOR GOOD AIR FLOW

USE AUTO DRY CYCLES FOR

BETTER FABRIC CARE AND ENERGY SAVINGS

Use the Auto Dry cycles to provide the most energy savings and enhanced fabric care from the dryer. During Auto Dry cycles,

drying air temperature and moisture level are sensed in the load. This sensing occurs throughout the drying cycle and the dryer

shuts o when the load reaches the selected dryness. Choose Normal cycle to save energy.

With Time Cycle, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to over-drying.

Use Time Cycle for the occasional damp load that needs a little more drying time or when using the drying rack.

Maintain good air ow by:

Cleaning your lint screen before each load.

Replacing plastic or foil vent material with 4" (102 mm)

diameter heavy, rigid vent material.

Using the shortest length of vent possible.

Using no more than four 90° elbows in a vent system;

each bend and curve reduces air ow.

Removing lint and debris from the exhaust hood.

Removing lint from the entire length of the vent system

at least every 2 years. When cleaning is complete,

be sure to follow the Installation Instructions supplied

with your dryer for nal product check.

Clearing away items from the front the dryer.

Good Air Flow

Along with heat, dryers require good air ow to eciently

dry laundry. Proper venting will reduce your drying times

and improve your energy savings. See Installation

Instructions.

The venting system attached to the dryer plays a big role

in good air ow.

Service calls caused by improper venting are not covered

by the warranty and will be paid by the customer, regardless

of who installed the dryer.

Good Better

Not all features and options are available on all models.

Appearance may vary.

CONTROL PANEL AND FEATURES

DRYER CYCLE KNOB

Turn the knob to select a cycle for your laundry load.

See “Cycle Guide” for detailed descriptions of cycles.

Timed Dry

Will run the dryer for the specied time on the control.

On models with a selectable temperature knob, you may

choose a setting based on the fabrics in your load. Drying

time and temperature will depend on your dryer model.

Auto Dry

Auto Dry cycles give the best drying in the shortest time.

Drying time will vary based on fabric type, load size, and

dryness setting.

Air Only

Use the Air Only setting to dry foam, rubber, plastic,

or heat-sensitive fabrics.

Wrinkle Guard™ function (on some models)

When you are unable to remove a load of clothes

from the dryer as soon as it stops, wrinkles can form.

The WRINKLE GUARD™ function periodically tumbles,

rearranges, and us the load without heat to help keep

wrinkles from forming, for up to 40 minutes at the end

of a cycle.

Dry Temp (on some models)

Select a drying temperature based on the fabrics in

your load. If you are unsure of the temperature to select

for a load, select the lower setting rather than the higher

setting. See “Cycle Guide.”

Cycle Signal/PUSH TO START

The Cycle Signal produces an audible sound when the drying

cycle is nished. On some models, this knob is combined with

the PUSH to START button. Promptly removing clothes at the

end of the cycle reduces wrinkling.

Turn the CYCLE SIGNAL knob to select the desired setting

(On or O). With combined buttons, press and hold the

CYCLE SIGNAL/PUSH to START button to start the dryer.

On models without the cycle signal, press the PUSH to START

button to start the dryer.

NOTE: During the Wrinkle Guard™ function and when

the Cycle Signal is on, the tone will sound every 5minutes

until the clothes are removed or the Wrinkle Guard™

function ends.

NOTE: If loads do not seem as dry as you would like, select More next time you dry a similar load. If loads seem drier than you like, select Less next

time you dry a similar load.

CYCLE GUIDE – AUTO DRY CYCLES

Not all cycles and settings are available on all models. Settings and options shown in bold are default settings for that cycle.

AUTO DRY – Senses moisture in the load or air temperature and shuts o when the load reaches the selected dryness level.

Depending on model, temperature may be selected on cycle knob or be a separate control. Choose Normal to save energy.

CYCLE GUIDE – TIMED DRY CYCLES

Not all cycles and settings are available on all models.

TIMED DRY – Will run the dryer for the specied time on the control. Depending on model, temperature may be selected on cycle

knob or be a separate control.

Setting the Drying Temperature

If your dryer has multiple temp settings:

A High Cotton temp setting may be used for drying heavyweight items such as towels and work clothes.

A Low Delicates or Medium Casual temp setting may be used for drying medium-weight items such as sheets, blouses, dresses,

underwear, permanent press fabrics, and some knits.

Use a Air Only (no heat) setting for foam, rubber, plastic, or heat-sensitive fabrics.

Line dry bonded or laminated fabrics.

NOTE: If you have questions about drying temperatures for various loads, refer to the care label directions.

Items to dry:

Dry

Temp:

Dryness

Level:

Available

Options:

Cycle Details:

Jeans, heavy work

clothes, towels

High Cotton More

Normal

Less

Cycle Signal

Dry Temp

Automatic cycles give the best drying in the

shortest time. Drying time varies based on

load size, and dryness setting.

Select a drying temperature based on the

fabrics in your load. If you are unsure of the

temperature to select for a load, select the

lower setting rather than the higher setting.

Work clothes, medium

weight fabrics, sheets

Medium Casual More

Normal

Less

Cycle Signal

Dry Temp

Casual, shirts, pants,

lightweight items,

synthetics, delicates,

athletic wear

Low Delicates More

Normal

Less

Cycle Signal

Dry Temp

Items to dry:

Cycle:

Dry

Temp:

Available

Options:

Cycle Details:

Any load Timed Dry Any Dry Temp Select a drying temperature based on the

fabrics in your load. If you are unsure of the

temperature to select for a load, select the

lower setting rather than the higher setting.

Any load Touch up Any N/A This is the last step in a cycle that uses

heat. The load is cooled slowly to reduce

wrinkling and make it easier to handle.

Use this cycle to smooth wear or packing

wrinkles.

Rubber, plastic, heat

sensitive fabrics

Air Only No heat Time Adjustment Use a Air Only (no heat) setting for foam,

rubber, plastic, or heat-sensitive fabrics.

1. Clean the lint screen

Clean the lint screen before each load. Pull the lint screen out of

its holder. Roll lint o the screen with your ngers. Do not rinse or

wash screen to remove lint. Push the lint screen rmly back into

place. For additional cleaning information, see “Dryer Care.”

2. Load the dryer

Place laundry in the dryer. Close the door. Do not tightly pack

the dryer; clothes should be able to tumble freely.

NOTE: Your model may have a dierent door than the one

shown. Some models have drop down doors.

WARNING: To reduce the risk of fire, electric shock, or injury

to persons, read the IMPORTANT SAFETY INSTRUCTIONS

before operating this appliance.

USING YOUR DRYER

6. Press and hold PUSH to START

to begin cycle

Press and hold the PUSH to START button to begin the cycle.

Promptly remove garments after cycle has completed to

reduce wrinkling. The Wrinkle Guard™ function at the end of

the cycle avoids wrinkling when you are unable to remove a load

from the dryer as soon as it stops.

4. Set temperature (on some models)

Turn the DRY TEMP knob to change the drying temperature

setting. See “Setting the Drying Temperature.”

3. Select the desired cycle

Select the desired cycle for your load. See the “Cycle Guide”

for more information about each cycle.

Auto Dry cycles

You can select a dierent dry level, depending on your load,

by turning the knob to More, Normal, or Less.

Selecting More, Normal, or Less automatically adjusts the

dryness level at which the dryer will shut o. Once a dry level

is set, it cannot be changed without stopping the cycle.

Auto Dry cycles give the best drying in the shortest time. Drying

time varies based on fabric type, load size, and dryness setting.

NOTE: More Dry removes more load moisture. Normal Dry is

used for a starting point for Auto Dry cycles. Choose normal

to save energy. Less Dry removes less moisture and is used for

loads you may want to put on a hanger to complete drying.

5. Select Cycle Signal, if desired

(on some models)

Turn the CYCLE SIGNAL knob to select the desired setting

(On or O). The Cycle Signal produces an audible sound when

the drying cycle is nished. Promptly removing clothes at the

end of the cycle reduces wrinkling.

NOTE: During the Wrinkle Guard™ function and if the Cycle

Signal is on, the tone will sound every 5minutes until the clothes

are removed, or the Wrinkle Guard™ function ends.

Appearance may vary.

DRYER CARE

Keep dryer area clear and free from items that would block

the air ow for proper dryer operation. This includes clearing

piles of laundry in front of the dryer.

Cleaning the lint screen

Every load cleaning

The lint screen is located in the dryer. A screen blocked

by lint can increase drying time.

To clean:

1. Pull the lint screen out of its holder. Roll lint o

the screen with your ngers. Do not rinse or wash

screen to remove lint.

2. Push the lint screen rmly back into place.

IMPORTANT:

Do not run the dryer with the lint screen loose, damaged,

blocked, or missing. Doing so can cause overheating and

damage to both the dryer and fabrics.

If lint falls o the screen into the dryer during removal,

check the exhaust hood and remove the lint. See

“Venting Requirements” in the Installation Instructions.

As needed cleaning

Laundry detergent and fabric softener residue can build up

on the lint screen. This buildup can cause longer drying times

for your clothes, or cause the dryer to stop before your load

is completely dry. The screen is probably clogged if lint falls

o while the screen is in the dryer.

Clean the lint screen with a nylon brush every 6 months,

or more frequently, if it becomes clogged due to a residue

buildup.

To wash:

1. Roll lint o the screen with your ngers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent.

Scrub lint screen with the brush to remove residue buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel. Reinstall

screen in dryer.

Cleaning the dryer interior

To clean dryer drum

1. Apply a liquid, nonammable household cleaner to the

stained area of the drum and rub with a soft cloth until

stain is removed.

2. Wipe drum thoroughly with a damp cloth.

3. Tumble a load of clean cloths or towels to dry the drum.

NOTE: Garments that contain loose dyes, such as denim blue

jeans or brightly colored cotton items, may discolor the dryer

interior. These stains are not harmful to your dryer and will

not stain future loads of clothes. Dry these items inside out

to avoid drum staining.

Removing accumulated lint

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often,

depending on dryer usage. Cleaning should be done

by a qualied servicer.

From the Exhaust Vent

Lint should be removed every 2 years, or more often,

depending on dryer usage.

Cleaning the dryer location

Changing the drum light (on some models)

1. Unplug dryer or disconnect power.

2. Open the dryer door. Locate the light bulb cover on the

back wall of the dryer. Using a Phillips head screwdriver,

remove the screw located in the lower right-hand corner

of the cover. Remove the cover.

3. Turn bulb counterclockwise. Replace the bulb with

a 10-watt appliance bulb only. Replace the cover

and secure with the screw.

4. Plug in dryer or reconnect power.

Vacation, storage, and moving care

Non-Use or Storage Care

Operate your dryer only when you are at home. If you will

be on vacation or not using your dryer for an extended

period of time, you should:

1. Unplug dryer or disconnect power.

2. (For gas dryers only): Close shut-o valve to gas

supply line.

3. Clean lint screen. See “Cleaning the Lint Screen.”

Moving Care

For power supply cord-connected dryers:

1. Unplug the power supply cord.

2. Make sure leveling legs are secure in dryer base.

3. Use tape to secure dryer door.

For direct-wired dryers:

1. Turn o power at fuse or breaker box.

2. Disconnect wiring.

3. Make sure leveling legs are secure in dryer base.

4. Use tape to secure dryer door.

For gas dryers:

1. Unplug or disconnect power to dryer.

2. Close shut-o valve to gas supply line and disconnect.

3. Make sure leveling legs are secure in dryer base.

4. Use tape to secure dryer door.

Reinstalling the Dryer

Follow the Installation Instructions to locate, level,

and connect the dryer.

TROUBLESHOOTING

If you experience Possible Causes Solution

Clothes are not drying

satisfactorily, drying

times are too long

Lint screen clogged with lint. Lint screen should be cleaned before each load.

The Air Only cycle has been selected. Select the right cycle for the types of garments being dried.

See “Cycle Guide.”

Load too large and heavy to dry quickly. Separate the load to tumble freely.

Exhaust vent or outside exhaust hood

clogged with lint, restricting air movement.

Run the dryer for 5–10 minutes. Hold your hand under the

outside exhaust hood to check air movement. If you do not feel

air movement, clean exhaust system of lint or replace exhaust

vent with heavy metal or exible metal vent. Make sure vent

is not crushed or kinked. See Installation Instructions.

Fabric softener sheets blocking the grill. Use only one fabric softener sheet, and use it only once.

Exhaust vent not the correct length. Check that the exhaust vent is not too long or has too many

turns. Long venting will increase drying times. Make sure vent

is not crushed or kinked. See Installation Instructions.

Exhaust vent diameter not the correct size. Use 4" (102mm) diameter vent material.

Dryer located in a room with temperature

below 45ºF (7ºC).

Proper operation of dryer cycles requires temperatures above

45ºF (7ºC).

Dryer located in a closet without adequate

openings.

Closet doors must have ventilation openings at the top and

bottom of the door. The front of the dryer requires a minimum

of 1" (25mm) of airspace, and, for most installations, the rear

of the dryer requires 5" (127mm). See Installation Instructions.

Dryer will not run Door not closed completely. Make sure the dryer door is closed completely.

PUSH to START button not pressed rmly

or held long enough.

Press and hold the PUSH to START button until you hear the

dryer drum moving.

Household fuse is blown or circuit breaker

has tripped.

Electric dryers use 2 household fuses or circuit breakers. The

drum may be turning, but you may not have heat. Replace both

fuses or reset the circuit breaker. If the problem continues, call

an electrician.

Incorrect power supply. Electric dryers require 240-volt power supply. Check with a

qualied electrician.

Wrong type of fuse. Use a time-delay fuse.

Unusual sounds Dryer had a period of non-use. If the dryer hasn’t been used for awhile, there may be a

thumping sound during the rst few minutes of operation.

A coin, button, or paper clip is caught

between the drum and front or rear of the

dryer.

Check the front and rear edges of the drum for small objects.

Clean out pockets before laundering.

It is a gas dryer. The gas valve clicking is a normal operating sound.

The four legs are not installed, and the

dryer is not level front to back and side

to side.

The dryer may vibrate if not properly installed. See Installation

Instructions.

Clothing knotted or balled up. When balled up, the load will bounce, causing the dryer

to vibrate. Separate the load items and restart the dryer.

No heat Household fuse is blown or circuit breaker

has tripped.

The drum may be turning, but you may not have heat. Electric

dryers use 2 household fuses or circuit breakers. Replace both

fuses or reset the circuit breaker. If the problem continues, call

an electrician.

Supply line valve not open. For gas dryers, be sure the valve on the supply line is open.

Incorrect power supply. Electric dryers require 240-volt power supply. Check with

a qualied electrician.

TROUBLESHOOTING cont.

If you experience Possible Causes Solution

Cycle time too short Automatic cycle ending early. The load may not be contacting the sensor strips. Level the

dryer.

Use Timed Dry for very small loads. Change the dry level

setting on Auto Dry cycles.

Increasing or decreasing the dry level setting will change the

amount of drying time in a cycle.

Lint on load Lint screen clogged. Lint screen should be cleaned before each load.

Stains on load or drum Dryer fabric softener not properly used. Add dryer fabric softener sheets at the beginning of the cycle.

Fabric softener sheets added to a partially dried load can

stain your garments.

Drum stains are caused by dyes in clothing (usually blue jeans).

These will not transfer to other clothing.

Loads are wrinkled The load was not removed from dryer at

the end of the cycle.

The Wrinkle Guard

™

function tumbles the load without heat

for 40 minutes at the end of the cycle to avoid wrinkling.

Dryer tightly packed. Dry smaller loads that can tumble freely reduce wrinkles from

forming.

Odors You have recently been painting, staining,

or varnishing in the area where your dryer

is located.

If so, ventilate the area. When the odors or fumes are gone

from the area, rewash and dry the clothing.

The electric dryer is being used for the rst

time.

The new electric heating element may have an odor. The odor

will be gone after the rst cycle.

Load is too hot Laundry items were removed from the

dryer before the end of the cycle.

Allow Cool Down to nish before removing laundry from dryer.

All cycles are cooled slowly to reduced wrinkling and make it

easier to handle. Items removed before Cool Down may feel

very warm.

A high temperature cycle was used or the

Dry Temp was set on high.

Select a lower temperature, and use an automatic drying cycle.

These cycles sense the temperature or the moisture level in the

load and shut o when the load reaches the selected dryness.

This reduces overdrying.

KENMORE APPLIANCE WARRANTY

PROTECTION AGREEMENTS

Master Protection Agreements

Congratulations on making a smart purchase. Your new Kenmore

product is designed and manufactured for years of dependable

operation.

But like all products, it may require preventive maintenance or

repair from time to time. That’s when having a Master Protection

Agreement can save you money and aggravation.

The Master Protection Agreement also helps extend the life

of your new product. Here’s what the Agreement* includes:

Parts and labor needed to help keep products operating properly

under normal use, not just defects. Our coverage goes well

beyond the product warranty. No deductibles, no functional

failure excluded from coverage—real protection.

Expert service by a force of more than 10,000 authorized Sears

service technicians, which means someone you can trust will be

working on your product.

Unlimited service calls and nationwide service, as often as you

want us, whenever you want us.

– replacement of your covered product if four or more product

failures occur within twelve months.

Product replacement if your covered product can’t be xed.

Annual Preventive Maintenance Check at your request –

no extra charge.

Fast help by phone – we call it Rapid Resolution – phone support

from a Sears representative on all products. Think of us as a

“talking owner’s manual.”

Power surge protection against electrical damage due

to power uctuations.

Rental reimbursement if repair of your covered product takes

longer than promised.

25% discount o the regular price of any non-covered repair

service and related installed parts.

Once you purchase the Agreement, a simple phone call is all

that it takes for you to schedule service. You can call anytime

day or night, or schedule a service appointment online.

The Master Protection Agreement is a risk free purchase. If you

cancel for any reason during the product warranty period, we

will provide a full refund. Or, a prorated refund anytime after the

product warranty period expires. Purchase your Master Protection

Agreement today! Some limitations and exclusions apply.

For prices and additional information in the U.S.A., call

1-800-827-6655. *Coverage in Canada varies on some items.

For full details, call Sears Canada at 1-800-361-6665.

Sears Installation Service

For Sears professional installation of home appliances, garage

door openers, water heaters, and other major home items,

in the U.S.A. or Canada, call 1-800-4-MY-HOME

KENMORE LIMITED WARRANTY

FOR ONE YEAR from the date of sale this appliance is warranted

against defects in material or workmanship when it is correctly

installed, operated, and maintained according to all supplied

instructions.

WITH PROOF OF SALE, a defective appliance will receive free

repair or replacement at option of seller.

For warranty coverage details to obtain free repair or

replacement, visit the web page: www.kenmore.com/warranty.

This warranty applies for only 90 DAYS from the sale date in the

United States, and is void in Canada, if this appliance is ever used

for other than private household purposes.

This warranty covers ONLY defects in material and

workmanship, and will NOT pay for:

1. Expendable items that can wear out from normal use, including

but not limited to lters, belts, bags, or screw-in base light

bulbs.

2. A service technician to clean or maintain this appliance, or to

instruct the user in correct appliance installation, operation, and

maintenance.

3. Service calls to correct appliance installation not performed

by Sears authorized service agents, or to repair problems with

house fuses, circuit breakers, house wiring, and plumbing or gas

supply systems resulting from such installation.

4. Damage to or failure of this appliance resulting from

installation not performed by Sears authorized service agents,

including installation that was not in accord with electrical, gas,

or plumbing codes.

5. Damage to or failure of this appliance, including discoloration

or surface rust, if it is not correctly operated and maintained

according to all supplied instructions.

6. Damage to or failure of this appliance, including discoloration

or surface rust, resulting from accident, alteration, abuse, misuse

or use for other than its intended purpose.

7. Damage to or failure of this appliance, including discoloration

or surface rust, caused by the use of detergents, cleaners,

chemicals, or utensils other than those recommended in all

instructions supplied with the product.

8. Damage to or failure of parts or systems resulting from

unauthorized modications made to this appliance.

9. Service to an appliance if the model and serial plate is missing,

altered, or cannot easily be determined to have the appropriate

certication logo.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION

OF REMEDIES

Customer’s sole and exclusive remedy under this limited warranty

shall be product repair or replacement as provided herein. Implied

warranties, including warranties of merchantability or tness

for a particular purpose, are limited to one year or the shortest

period allowed by law. Seller shall not be liable for incidental

or consequential damages. Some states and provinces do not

allow the exclusion or limitation of incidental or consequential

damages, or limitation on the duration of implied warranties of

merchantability or tness, so these exclusions or limitations may

not apply to you.

This warranty applies only while this appliance is used in the

United States or Canada*.

This warranty gives you specic legal rights, and you may also

have other rights which vary from state to state.

* In-home repair service is not available in all Canadian

geographical areas, nor will this warranty cover user or servicer

travel and transportation expenses if this product is located

in a remote area (as dened by Sears Canada Inc.) where an

authorized servicer is not available.

Sears Brands Management Corporation

Homan Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2C3

10/2014

SEGURIDAD DE LA SECADORA

IMPORTANTE: Cuando descarte o guarde su vieja secadora de ropa, quítele la puerta.

ÍNDICE

SEGURIDAD DE LA SECADORA ........................................... 14

REVISE QUE EL SISTEMA DE VENTILACIÓN TENGA

UN BUEN FLUJO DE AIRE ........................................................ 16

USE AUTO DRY (Secado automático) PARA UN MEJOR

CUIDADO DE LAS TELAS Y AHORRO DE ENERGÍA ......... 16

PANEL DE CONTROL Y CARACTERÍSTICAS ....................... 17

GUIÁ DE CICLOS ...................................................................... 18

USO DE LA SECADORA ......................................................... 19

CUIDADO DE LA SECADORA ..................................................21

SOLUCIÓN DE PROBLEMAS ...................................................23

CONTRATOS DE PROTECCIÓN .............................................25

GARANTÍA ................................................................................25

AYUDA O SERVICIO TÉCNICO ............................................. 40

Mantenga un buen ujo de aire

haciendo lo siguiente:

Limpiar el ltro de pelusa antes de cada carga.

Reemplazar el material del ducto de plástico u hoja de

metal con uno de metal pesado rígido de 4" (102 mm)

de diámetro.

Use un ducto con la longitud más corta posible.

No utilice más de 4 codos de 90° en un sistema

de ventilación; cada ángulo y curva reduce el ujo

de aire.

Quite la pelusa y los desechos de la capota

de ventilación.

Quite la pelusa de toda la longitud del sistema

de ventilación al menos cada 2 años. Cuando haya

terminado la limpieza, revise por última vez el producto

asegurándose de seguir las Instrucciones de instalación

que acompañan a su secadora.

Retire los artículos que estén frente a la secadora.

Buen ujo de aire

Además del calor, las secadoras también necesitan un

buen ujo de aire para secar las prendas ecazmente.

La ventilación adecuada reducirá la duración del secado

y mejorará su ahorro de energía. Consulte las Instrucciones

de instalación.

El sistema de ventilación sujeto a la secadora juega un papel

muy importante para el ujo de aire adecuado.

Las visitas de servicio debidas a la ventilación inadecuada

no están cubiertas por la garantía y correrán por cuenta del

cliente, sin importar quién haya instalado la secadora.

Bien Mejor

REVISE QUE EL SISTEMA DE VENTILACIÓN TENGA UN BUEN FLUJO DE AIRE

Use AUTO DRY (Secado automático) PARA UN MEJOR CUIDADO

DE LAS TELAS Y AHORRO DE ENERGÍA

Utilice los ciclos Auto Dry (Secado automático) para obtener el mayor ahorro de energía y un mejor cuidado de las telas con la

secadora. Durante los ciclos de Auto Dry (Secado automático) se detectan la temperatura del aire de secado y el nivel de humedad

en la carga. Esta detección se realiza durante todo el ciclo de secado y la secadora se apaga cuando la carga alcanza el nivel

de sequedad seleccionado. Elija el ciclo Normal para ahorrar energía.

Con Time Cycle (Ciclo por tiempo), la secadora funciona durante el tiempo jado y algunas veces puede dar lugar a encogimiento,

arrugas y estática a causa del exceso de secado. Utilice Time Cycle (Ciclo por tiempo) ocasionalmente, para las cargas húmedas

que necesiten un poco más de tiempo de secado o cuando utilice el estante de secado.

PANEL DE CONTROL Y CARATERÍSTICAS

PERILLA DE CICLOS DE LA SECADORA

Gire la perilla de ciclos de lavado para seleccionar un

ciclo para su carga. Consulte “Guía de ciclos” para ver

descripciones detalladas de los ciclos.

Time Dry (Secado por tiempo)

Hará funcionar la secadora durante el tiempo especicado

en el control. En modelos con una perilla para seleccionar la

temperatura, puede elegir un ajuste basado en las telas de su

carga. El tiempo y la temperatura de secado dependerán del

modelo de su secadora.

Auto Dry (Secado automático)

Los ciclos Auto Dry (Secado automático) le proporcionan el

mejor secado en el tiempo más corto. El tiempo del secado

variará según el tipo de tela, el tamaño de la carga y el

ajuste de sequedad.

Air Only (Sólo aire)

Use el ajuste Sólo aire (Air Only) para secar espuma, goma,

plástico o telas sensibles al calor.

Opción Wrinkle Guard™ (Protección antiarrugas)

(en algunos modelos)

Si no es posible retirar la carga de la secadora tan pronto

como ésta se detenga, se pueden formar arrugas. La función

WRINKLE GUARD™ (Protección antiarrugas) periódicamente

da vueltas, acomoda y esponja la ropa, sin calor, para

ayudar a evitar que se formen arrugas hasta 40 minutos

al nal del ciclo.

Dry Temp (Temperatura de secado)

(en algunos modelos)

Seleccione una temperatura de secado según las telas de

su carga. Si tiene duda respecto a la temperatura que debe

seleccionar para una carga de ropa, elija el ajuste más bajo

en vez del ajuste más alto. Vea “Guía de ciclos”.

Cycle Signal/PUSH TO START (Señal de ciclos/

Presione para poner en marcha)

Cycle Signal (Señal de ciclos) emite un sonido audible

una vez que el ciclo de secado ha terminado. En algunos

modelos, esta perilla está combinada con el botón PUSH to

START (Presione para poner en marcha). El sacar la ropa con

prontitud al nal del ciclo reduce la formación de arrugas.

Gire la perilla de CYCLE SIGNAL (Señal de ciclos) para

seleccionar el ajuste deseado (On – Encendido, u O –

Apagado). Con los botones combinados, presione y sostenga

el botón CYCLE SIGNAL/PUSH to START (Señal de ciclos/

Presione para poner en marcha) para poner la secadora en

marcha. En modelos sin señal de ciclos, presione el botón de

PUSH to START (Presione para poner en marcha) para poner

la secadora en marcha.

NOTA: Durante la función Wrinkle Guard™ (Protección

antiarrugas) y esté encendida Cycle Signal (Señal de ciclos),

el tono se escuchará cada 5 minutos hasta que se saque

la ropa o hasta que haya terminado la función Wrinkle

Guard™ (Protección antiarrugas).

No todas las características y opciones están disponibles en todos los modelos.

La apariencia puede variar.

GUÍA DE CICLOS – AUTO DRY (Secado automático)

No todos los ciclos y ajustes están disponibles en todos los modelos. Los ajustes y las opciones que se muestran en negrita son los ajustes

por defecto para ese ciclo.

AUTO DRY (SECADO AUTOMÁTICO) – Detecta la humedad en la carga o la temperatura del aire y se apaga cuando la carga alcanza

el nivel de sequedad seleccionado. Dependiendo del modelo, la temperatura puede seleccionarse con la perilla de ciclos o ser un control

por separado. Elija Normal para ahorrar energía.

GUÍA DE CICLOS – CICLOS TIMED DRY (Secado por tiempo)

No todos los ciclos y ajustes están disponibles en todos los modelos.

TIMED DRY (Secado por tiempo) – Hará funcionar la secadora durante el tiempo especicado en el control. Dependiendo del modelo,

la temperatura puede seleccionarse con la perilla de ciclos o ser un control por separado.

NOTA: Si las cargas no parecen estar tan secas como le gustaría, seleccione More (Más) la próxima vez que seque una carga similar.

Si le parece que las prendas están más secas de lo que las desea, seleccione Less (Menos) la próxima vez que seque una carga similar.

Cómo jar la temperatura de secado

Si su secadora tiene múltiples ajustes de temperatura:

Se puede usar un ajuste de temperatura High Cotton (Alta y Algodón) para secar artículos pesados tales como toallas y ropa

de trabajo.

Se puede usar un ajuste de temperatura Low Delicates (Baja y Ropa delicada) o Medium Casual (Media e Informal) para secar

artículos de peso mediano tales como sábanas, blusas, vestidos, ropa interior, telas de planchado permanente y algunos tejidos

de punto.

Use un ajuste de Air Only (Sólo aire) (sin calor) para artículos de espuma, goma, plástico o telas sensibles al calor.

Seque en el tendedero las telas laminadas o tratadas.

NOTA: Si tiene dudas respecto a la temperatura que debe seleccionar para distintas cargas de ropa, consulte las instrucciones

de cuidado de las etiquetas.

Artículos

para secar:

Temperatura

de secado:

Nivel de

sequedad:

Opciones

disponibles

Detalles de los ciclos:

Pantalones de mezclilla,

ropa de trabajo pesada,

toallas

High Cotton

(Alta y Algodón)

More (Más)

Normal

Less (Menos)

Cycle Signal

(Señal de ciclos)

Dry Temp

(Temperatura

de secado)

Los ciclos automáticos le proporcionan el mejor

secado en el tiempo más corto. El tiempo de

secado varía según el tamaño de la carga y

el ajuste de sequedad.

Seleccione una temperatura de secado según

las telas de su carga. Si tiene duda respecto a

la temperatura que debe seleccionar para una

carga de ropa, elija el ajuste más bajo en vez

del ajuste más alto.

Ropa de trabajo, telas

de peso mediano,

sábanas

Medium Casual

(Media e Informal)

More (Más)

Normal

Less (Menos)

Cycle Signal

(Señal de ciclos)

Dry Temp

(Temperatura

de secado)

Ropa informal, camisas,

pantalones, artículos

livianos, prendas

sintéticas, ropa delicada,

ropa deportiva

Low Delicates (Baja

y Ropa delicada)

More (Más)

Normal

Less (Menos)

Cycle Signal

(Señal de ciclos)

Dry Temp

(Temperatura

de secado)

Artículos para secar:

Ciclo:

Temperatura

de secado:

Opciones

disponibles:

Detalles de los ciclos:

Cualquier carga Timed Dry

(Secado por tiempo)

Cualquiera Dry Temp

(Temperatura de

secado)

Seleccione una temperatura de secado

según las telas de su carga. Si tiene duda

respecto a la temperatura que debe

seleccionar para una carga de ropa, elija

el ajuste más bajo en vez del ajuste más alto.

Cualquier carga Touch up (Retoque) Cualquiera N/D Este es el último paso en un ciclo que utiliza

calor. La carga se enfría lentamente para

reducir las arrugas y hacer que la carga

sea más fácil de manipular. Use este ciclo

para suavizar la ropa o alisar las arrugas.

Goma, plástico, telas

sensibles al calor

Air Only

(Sólo aire)

Sin calor

(No heat)

Ajuste del tiempo Use un ajuste de Air Only (Sólo aire)

(sin calor) para artículos de espuma,

goma, plástico o telas sensibles al calor.

USO DE LA SECADORA

1. Limpie el ltro de pelusa

Limpie el ltro de pelusa antes de cada carga. Jale el ltro de

pelusa directamente hacia arriba. Quite la pelusa enrollándola

con los dedos. No enjuague ni lave el ltro para quitar la pelusa.

Empuje el ltro de pelusa rmemente hasta que quede en su lugar.

Para obtener más información sobre la limpieza, vea “Cuidado

de la secadora”.

2. Cargue la secadora

Ponga la ropa en la secadora. Cierre la puerta. No cargue la

secadora de manera apretada; las prendas deben poder girar

libremente.

NOTA : Su modelo puede tener una puerta diferente de la que

se muestra. Algunos modelos pueden tener puertas de abertura

vertical.

ADVERTENCIA: A fin de reducir el riesgo de incendio, de choque

eléctrico o de daños personales, lea las INSTRUCCIONES

IMPORTANTES DE SEGURIDAD antes de operar este aparato.

6. Presione y sostenga PUSH to START

(Presione para poner en marcha)

para comenzar el ciclo

Presione y sostenga el botón de PUSH to START (Presione para

poner en marcha) para comenzar el ciclo.

Saque las prendas en cuanto se haya completado el ciclo para

reducir las arrugas. La función Wrinkle Guard™ (Protección

antiarrugas) al nal del ciclo evita que se formen arrugas

cuando no pueda sacar la carga de la secadora en cuanto

se detiene.

4. Seleccione la temperatura

(en algunos modelos)

3. Seleccione el ciclo deseado

Seleccione el ciclo deseado para su carga. Para obtener más

información acerca de cada ciclo, vea la “Guía de ciclos”.

Ciclos Auto Dry (Secado automático)

Puede seleccionar un nivel de secado diferente según la carga,

girando la perilla hacia More (Más), Normal o Less (Menos).

Al seleccionar More (Más), Normal o Less (Menos) se ajusta

automáticamente el nivel de sequedad, en el cual se apagará

la secadora. Una vez que se haya jado el nivel de secado,

no podrá cambiarse si no se detiene el ciclo.

Los ciclos Auto Dry (Secado automático) le proporcionan

el mejor secado en el tiempo más corto. El tiempo de secado

varía según el tipo de tela, el tamaño de la carga y el ajuste

de sequedad.

NOTA: More Dry (Más seco) quita más humedad de la carga.

Normal Dry (Secado normal) se utiliza como un punto de

partida para los ciclos Auto Dry cycles (Secado automático).

Elija normal para ahorrar energía. Less Dry (Menos seco) quita

menos humedad y se usa para las cargas que desee terminar

de secar en una percha.

5. Seleccione Cycle Signal (Señal de ciclos),

si lo desea (en algunos modelos)

Gire la perilla de CYCLE SIGNAL (Señal de ciclos) para

seleccionar el ajuste deseado (On – Encendido, u O –

Apagado). Cycle Signal (Señal de ciclos) emite un sonido

audible una vez que el ciclo de secado ha terminado. El sacar

la ropa con prontitud al nal del ciclo reduce la formación

de arrugas.

NOTA: Durante la función Wrinkle Guard™ (Protección

antiarrugas) y si Cycle Signal (Señal de ciclos) está encendido,

el tono se escuchará cada 5 minutos hasta que se saque la

ropa o hasta que haya terminado la función Wrinkle Guard™

(Protección antiarrugas).

Gire la perilla de DRY TEMP (Temperatura de secado) para

cambiar el ajuste de temperatura de secado. Vea “Cómo jar

la temperatura de secado”.

La apariencia puede variar.

La page charge ...

Kenmore 62332 Le manuel du propriétaire

Marque: Kenmore

Modèle: 62332

Catégorie: Sèche-linge électriques

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Kenmore 62332 Owner's manual
español: Kenmore 62332 El manual del propietario

Documents connexes

Autres documents

Kenmore Elite 71633 Guide de démarrage rapide