3M DBI-SALA® Floor Mount Sleeve Davit Base 8518347, 1 EA Mode d'emploi

Marque: 3M

Modèle: DBI-SALA® Floor Mount Sleeve Davit Base 8518347, 1 EA

Taper: Mode d'emploi

Ce manuel convient également à

DBI-SALA® Confined Space Floor Mount Sleeve Davit Base 8516190, 1 ea

FORM NO: 5903771

REV: A

The Ultimate in Fall Protection

ADVANCED

FLOOR MOUNT SLEEVES

Model Numbers: 8516190, 8518347

Figure 1 – 8516190 8518347

8516190, 8518347

8516190

8518347

INSTRUCTION MANUAL

ANSI Z359.1

This manual is intended to meet the Manufacturer’s Instructions as required by ANSI Z359.1

and should be used as part of an employee training program as required by OSHA

SPECIFICATIONS:

DESCRIPTION:

The DBI-SALA Floor Mount Bases are designed for

mounting to horizontal concrete or steel structure

THESE BASES ARE ONLY COMPATIBLE WITH DBI

SALA ADVANCED DAVIT MASTS AND EXTENSIONS.

IMPORTANT: All connecting systems, (self retracting lifelines, winches and energy absorbing lanyards) used

with the davit arm and base system shall limit the arresting forces to 900 lbs (4 kN).

GENERAL SPECIFICATIONS - MODEL 8516190:

Rated Capacity (working load)

Vertical Load

450 lbs (205 kg)

5000 lbs (22.24 kN)

MATERIALS & CONSTRUCTION:

General Construction Welded Steel

Material Mild Steel

Hardware (Minimum) Gr. 8 Steel, Zinc Plated

Finish (Steel) Zinc Plated

Plating Specication ASTM Designation

B633, Type II, Class 1

APPLICATION RESTRICTIONS:

For use with Capital Safety Systems

products & accessories only.

Each installation must be approved to local

standards by a qualied engineer.

If base material does not meet the

minimum requirements, reinforcement

must be added to meet the minimum

requirements.

GENERAL SPECIFICATIONS - MODEL 8518347

Rated Capacity (working load)

Vertical Load

450 lbs (205 kg)

5000 lbs (22.24 kN)

MATERIALS & CONSTRUCTION:

General Construction Stainless Steel

Material 304 SS

Hardware (Minimum) Gr. 8 Steel, Zinc Plated,

Finish (Stainless Steel) Brush Blast

Plating Specication None

APPLICATION RESTRICTIONS:

For use with Capital Safety Systems

products & accessories only.

Each installation must be approved to local

standards by a qualied engineer.

If base material does not meet the

minimum requirements, reinforcement

must be added to meet the minimum

requirements.

Figure 2 – Base Dimensions

25.4 cm

(10 in)

(REF)

23.5 cm

(9.25 in)

(REF)

Diameter

cm (25/32 in)

25.4 cm

(10 in)

(REF)

21.6 cm

(8.5 in)

(REF)

10.1 cm

(4 in)

(REF)

21.6 cm

(8.5 in)

(REF)

Ø 25/32 in (2 cm)

4 in

(10.1 cm)

10 in

(25.4 cm)

8.5 in

(21.6 cm)

9.25 in

(23.5 cm)

10 in

(25.4 cm)

8.5 in

(21.6 cm)

Table 1 – Mounting Requirement Minimums

73.6cm (29 inches) Offset

122cm (48 inches) Offset

Pullout Force Per Base 7784 lbf (34.6 kN) 8368 lbf (37.2 kN)

Shear Force N/A N/A

Moment Load Per Structure 87,000 in*lbs (9.8 kN*m) 86,400 in*lbs (9.7 kN*m)

Vertical Load Per Structure 5000 lbs (22.2 kN) 3000 lbs (13.3kN)

STRUCTURE

XX.XX

REFER TO

FASTENER

MANUFACTURER

SPECIFICATIONS

XX.XX

REFER TO

FASTENER

MANUFACTURER

SPECIFICATIONS

(MINIMUM)

(Minimum)

XX.XX

Refer to

Fastener

Manufacturer

Specifications

(Minimum)

XX.XX

Refer to

Fastener

Manufacturer

Specifications

NOTE: These numbers are based on a safety factor of 2:1. Refer to the fastener manufacturer specications for fastener

safety factors. It is recommended to maintain at least a safety factor of 2:1. Multiple safety factor must be taken into

account when determining fasteners.

IMPORTANT: Base installation must be approved to local regulations by a qualied engineer. Refer to the fastener

manufacturer for location of the fasteners, structure thickness, and structure type requirements

INSTALLATION:

IMPORTANT: Refer to the davit arm and fastener instructions for specic mounting requirements. There are

many factors that will determine a proper installation of the base, such as fastener material and davit arm

length. These factors must all be considered prior to base installation.

WARNING: Failure to follow Mounting Requirement Minimums and Installation instructions may lead to severe

injury and/or death.

Figure 3 – Example Install Method #1

Reference Mounting

Requirement Minimums

EDGE

5 in

12.7cm

9.25 in

23.49cm

Reference Fastener Mounting

Requirement Minimums

Edge / Fall

5 in

12.7 cm

9.25 in

(23.49 cm)

NOTE: There are different installation

methods for this davit base. (Figure 3 & 4

to the left depict installation examples.) See

Table 1 for specic installation guidelines.

(2:1 safety factor.)

1. Place davit base leg perpendicular to edge.

(See Figure 3 to left.) Using a Specication

approved drill bit and the davit base as a

guide, drill four holes into the deck.

2. Install the Specication approved

hardware.

3. A qualied engineer must verify the

structural installation meets local and

federal regulations.

4. A qualied engineer must recommend

the appropriate fasteners and determine

proper base placement on the mount

structure.

Figure 4 – Example Install Method #2

EDGE

Reference Mounting

Requirement Minimums

4 in

10.16cm

7 in (17.78cm)

Reference Fastener Mounting

Requirement Minimums

Edge / Fall

4 in

10.16 cm

7 in (17.78 cm)

IMPORTANT: All mounting hardware must

be able to withstand a minimum pull out

force of 8368 lbf (37.2 kN) each if using a 48

inch (122 cm) offset. If a 29 inch (73.6 cm)

offset is used, a minimum pullout 7784 lbf

(34.6 kN) is required. See Table 1 for specic

installion guidelines. (2:1 safety factor.)

1. Place davit base leg 45° (typical) off

perpendicular to edge. (See Figure 4 to

left.) Use a Specication approved drill bit

and the davit base as a guide, drill four

holes into the deck.

2. Install the Specication approved

hardware.

3. A qualied engineer must verify the

structural installation meets local and

federal regulations.

4. A qualied engineer must recommend

the appropriate fasteners and determine

proper base placement on the mount

structure.

4. DAVIT BASE INSPECTION:

BEFORE EACH USE:

IMPORTANT: Extreme working conditions (harsh environments, prolonged use) may require increasing the

frequency of inspections.

WARNING: If the base has been subjected to fall arrest forces, it must be immediately removed from service

and inspected. If the oor mount base fails inspection, remove from service and destroy, or contact Capital

Safety for repair or replacement.

Table 2 – Inspection and Maintenance Log

Serial Number(s): Date Purchased:

Model Number: Date of First Use:

Inspected By: Inspection Date:

Component: Inspection:

Authorized

Person or

Rescuer

Competent

Person

Davit Base

Ensure all bolts are secure and not damaged.

Base should be inspected directly after installation and at same intervals as

the arresting system for similar defects and/or unsafe conditions.

All labels must be present and fully legible.

If inspection reveals an unsafe or defective condition, remove the base from

service and destroy, or contact Capital Safety for repair or replacement.

Look for signs of corrosion on the entire unit.