Wattstopper
®
Wireless LonWorks Bridge with AES 256-bit/FIPS140.2 Encryption*
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
No: 25178 – 2/17 rev. 1
Catalog Number • Numéro de Catalogue • Número de Catálogo: WLT900-F
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
SPECIFICATIONS
Volts 12-24 VAC or VDC
UL Standards Tested UL 2043 plenum rated
902-928MHz Direct Sequence Spread Spectrum (DSSS)
Synchronous point-to-multipoint communication
Special Features
Includes unity gain antenna
FIPS-140.2 certified encrypted payload protection
DESCRIPTION AND OPERATION
The WLT900-F is designed to transport LonWorks
®
communication data over short to extended ranges using the 900 MHz frequency
(902-928). All devices are plug-and-play requiring no special programming tools. Using Hyperterminal, radios can be addressed to one
another in the field. The WLT900-F provides a AES-256 bit/FIPS 140.2 Security layer.
The WLT900-F Transceiver allows the user to create a long-range, wireless LonWorks network with numerous Client units (up to 16) per
Server transceiver.
Configuring a wireless link with the WLT900-F requires the establishment of five elements:
1. Each radio must know whether it is to be a Server or Client.
2. The Server must know how many Clients are expecting communication with it.
3. The Server and any given Client must agree on which radio frequency channel they are using.
This can be set manually using a HyperTerminal interface and preconfigured configuration files.
4. The Client must be assigned a unique subscriber ID to specify which time division slot it will use when communicating with the Server.
5. The Server and any given Client must share a common FIPS-140.2 certified encryption key and Network ID.
The Server automatically scans for the best of the 12 available radio frequency channels, encrypts LonWorks data received from the network,
and transmits it wirelessly to the correct Client. The Server is constantly monitoring the radio link and can automatically change the channel
if performance is degraded due to interference. If two Server units are very close to one another, they may interfere if operating on adjacent
frequency channels. Place them at least 20 feet apart or manually select non-adjacent channels for their operation. Also, the Client should be
placed at least 10 feet from the Server to avoid overloading the WLT900-F receiver.
Any LonWorks client device can be connected to a WLT900-F Client. Each Client encrypts the LonWorks traffic received from the attached
device and transmits the data wirelessly to its Server. Each Client can be plugged directly into an LonWorks network/device without adding
drivers or loading software. Essentially, once the Server/Client pair is configured and running, it behaves like a continuous LonWorks cable.
900 MHz Channel Table
1 903.12500 MHz 7 915.62500 MHz
2 905.20833 MHz 8 917.70833 MHz
3 907.29167 MHz 9 919.79167 MHz
4 909.37500 MHz 10 921.87500 MHz
5 911.45833 MHz 11 923.95833 MHz
6 913.54167 MHz 12 926.04167 MHz
WARNING: If using AC power option, a 24 VAC isolation transformer must be used! Ensure neither of the two secondaries are bonded.
NOTE: As with any RF network, plan ahead for proper antenna selection and placement. It is the intention of Wattstopper to provide a
reliable wireless communication device for existing LonWorks networks. However, in some conditions, reliability is determined
largely by correct antenna placement, which is the responsiblity of the installer. This product is NOT TO BE USED in situations
where life safety issues may arise. Wattstopper makes no claims, expressed or implied, of the products usefulness with
regard to specific applications. Determination of the product’s suitability for a particular application is the sole responsibility
of the purchasing parties. In any installation, ensure the devices are properly protected from the elements by installing in an
appropriate enclosure. Additional surge protection devices may be necessary to protect from lighting and/or power surges.
WARNING: Extra care must be taken when attaching the antenna to the bridge unit. Finger tight is sufficient, using tools may damage
the RPSMA connector if over tightened.