ID TECH uSign 300 Manuel utilisateur

Catégorie
Moniteurs à écran tactile
Taper
Manuel utilisateur
USER MANUAL
uSign™
Signature Capture Module
Model uSign 300
80109504-001
02-28-2012
Copyright © 2012, International Technologies & Systems Corp. All rights reserved.
Page 2 of 10
uSign 300 User Manual
FCC WARNING STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation of this device is subject to
the following conditions: this device may not cause harmful interference and this device
must accept any interference received, including interference that may cause undesired
operation.
CANADIAN DOC STATEMENT
This digital apparatus does not exceed the Class B limits for radio noise for digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de las classe B prescrites dans le Réglement sur le
brouillage radioélectrique édicté par les ministère des Communications du Canada.
CE STANDARDS
An independent laboratory performed testing for compliance to CE requirements. The
unit under test was found compliant to Class B.
ID TECH is a registered trademark of International Technologies & Systems Corporation.
uSign and Value through Innovation are trademarks of International Technologies &
Systems Corporation.
USB (Universal Serial Bus) Specification is Copyright by Compaq Computer Corporation,
Intel Corporation, Microsoft Corporation, and NEC Corporation. Windows, Excel, &
Notepad are registered trademarks of Microsoft Corporation.
Copyright © 2012, International Technologies & Systems Corp. All rights reserved.
Page 3 of 10
uSign 300 User Manual
LIMITED WARRANTY
ID TECH warrants to the original purchaser for a period of 12 months from the date of
invoice that this product is in good working order and free from defects in material and
workmanship under normal use and service. ID TECH’s obligation under this warranty is
limited to, at its option, replacing, repairing, or giving credit for any product which has,
within the warranty period, been returned to the factory of origin, transportation charges
and insurance prepaid, and which is, after examination, disclosed to ID TECH’s
satisfaction to be thus defective. The expense of removal and reinstallation of any item or
items of equipment is not included in this warranty. No person, firm, or corporation is
authorized to assume for ID TECH any other liabilities in connection with the sales of any
product. In no event shall ID TECH be liable for any special, incidental or consequential
damages to purchaser or any third party caused by any defective item of equipment,
whether that defect is warranted against or not. Purchaser’s sole and exclusive remedy for
defective equipment, which does not conform to the requirements of sales, is to have such
equipment replaced or repaired by ID TECH. For limited warranty service during the
warranty period, please contact ID TECH to obtain a Return Material Authorization
(RMA) number & instructions for returning the product.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE. THERE ARE
NO OTHER WARRANTIES OR GUARANTEES, EXPRESS OR IMPLIED, OTHER
THAN THOSE HEREIN STATED. THIS PRODUCT IS SOLD AS IS. IN NO EVENT
SHALL ID TECH BE LIABLE FOR CLAIMS BASED UPON BREACH OF EXPRESS
OR IMPLIED WARRANTY OF NEGLIGENCE OF ANY OTHER DAMAGES
WHETHER DIRECT, IMMEDIATE, FORESEEABLE, CONSEQUENTIAL OR
SPECIAL OR FOR ANY EXPENSE INCURRED BY REASON OF THE USE OR
MISUSE, SALE OR FABRICATIONS OF PRODUCTS WHICH DO NOT CONFORM
TO THE TERMS AND CONDITIONS OF THE CONTRACT.
The information contained herein is provided to the user as a convenience. While every
effort has been made to ensure accuracy, ID TECH is not responsible for damages that
might occur because of errors or omissions, including any loss of profit or other
commercial damage, nor for any infringements or patents or other rights of third parties
that may result from its use. The specifications described herein were current at the time
of publication, but are subject to change at any time without prior notice.
ID TECH is a registered trademark of International Technologies & Systems Corporation. uSign
and Value through Innovation are trademarks of International Technologies & Systems
Corporation.
ID TECH
10721 Walker Street
Cypress, CA 90630
(714) 761-6368
www.idtechproducts.com
Copyright © 2012, International Technologies & Systems Corp. All rights reserved.
Page 4 of 10
uSign 300 User Manual
Revision History
Revision Date Description of Changes By
A 02/28/2012 Initial release JW
Copyright © 2012, International Technologies & Systems Corp. All rights reserved.
Page 5 of 10
uSign 300 User Manual
Table of Contents
1.0 Introduction ..........................................................................................................................6
2.0 Features ................................................................................................................................6
3.0 Model Designations .............................................................................................................7
4.0 Terms & Abbreviations........................................................................................................7
5.0 Installing uSign ....................................................................................................................7
5.1 RS232 Communication Interface .................................................................................... 8
5.2 USB Communication Interface ....................................................................................... 8
6.0 Specifications .......................................................................................................................8
6.1 Power requirement .......................................................................................................... 8
6.2 Physical housing uSign 300 ............................................................................................ 8
6.3 LCD screen & Resistive touch pad ................................................................................. 8
6.4 Communication interface ................................................................................................ 9
6.5 LED ................................................................................................................................. 9
6.6 Agency Approvals .......................................................................................................... 9
6.7 Electronics MTBF ........................................................................................................... 9
6.8 Electro-Static Discharges (ESD)..................................................................................... 9
6.9 Environmental ................................................................................................................. 9
7.0 Outline Drawing.................................................................................................................10
Copyright © 2012, International Technologies & Systems Corp. All rights reserved.
Page 6 of 10
uSign 300 User Manual
1.0 Introduction
The use of electronically captured signatures has become common for Point of Service
(POS) applications. Electronic signature capture reduces transaction time, eliminates
sorting & sending paper, provides convenient electronic storage & transmission, and gives
legal accountability (non-repudiation) for POS transactions.
uSign™ is an electronic signature capture device with a back lighted graphic LCD display
and touch sensitive screen that is the signature panel. Authors can view their signatures in
real time during the signing process. Signatures are compressed and provided to a Host
system for signature & data storage. The LCD display allows for interactive text, which
supports pen-tap commands and function selections. The interactive Host operations
allow selections and navigations through transactions with just the stylus.
The LCD & touch sensitive screen are surrounded in a plastic housing. The housing
provides a tethered non-electronic stylus. The stylus is fastened to the housing in a way to
allow stylus replacement. A mounting plate secures the uSign housing to a counter top or
other mounting surface. An overlay covers and protects the signature area of the uSign
display. The overlay is removable allowing replacement if the signature area becomes
worn from stylus use. Customer specific front overlay designs are possible as needed by
an application.
The signature pad enclosed in a stylish housing. This uSign is a POS System level
product intended for signature capture at a transaction counter. A convenient palm rest
area below the signature panel provides support during the signing process.
2.0 Features
Electronic signature capture w Buffered signature capability
Sampling rate up to 190 dots per second
Real time signature capture with 5:1 compression
Raw data output available
Algorithms to filter spikes, provide Smoothing, & Calibration algorithms
Command & response driven operations through an API
Graphic display of signature during capture
Display graphics under Host control when not in signature process
Touch pad dot position matches LCD pixel locations
Operates with Windows XP, Vista and Windows 7 operating systems
Replaceable non-active tethered stylus
Resistive touch pad
RoHS compliant
Copyright © 2012, International Technologies & Systems Corp. All rights reserved.
Page 7 of 10
uSign 300 User Manual
3.0 Model Designations
uSign 300 IDUB-01x500
The “x” defines the communication interface, 2 = RS232 and 6 = USB
4.0 Terms & Abbreviations
COM Host communication port
HID Human Interface Device
Host Personal Computer, Terminal, or similar device
LCD Liquid Crystal Display
LED Light Emitting Diode
mA Milli-Amperes of electrical current
RS232 Serial communications
USB Universal Serial Bus, serial communications
VDC Volts Direct Current
5.0 Installing uSign
uSign is designed for an indoor environment. Locate the uSign where it is convenient to
operate and protected from heat or direct sunlight. Position the uSign so the signature pad
area is easy to reach and the immediate area is clear for authoring the signature. The
uSign housing has threaded inserts in the bottom and relief areas for hook & loop
fasteners. A metal mounting bracket with keyhole & screw mounting is mounted to the
back of the housing.
The uSign 300 with an RS232 interface uses a standard DE9 connector and uses a 5VDC
power adaptor. The input voltage on the power adaptors may be limited; do not exceed
the input voltage rating of the power adaptor. Connect the power adaptor after the other
connections are made.
The uSign having a USB communication interface receives power from the host through
the USB port.
For both interface types and when power is applied, the green & red LED on the uSign are
on for a moment, go off, and then the green is on and flashing. If the LED does not light,
check the connections and the availability of power from the power outlet. With the green
LED flashing, the LCD screen displays: “IDTECH uSign, Version x.xx.” When the
signature screen is touched or commands are received from a Host, the LED is turned off
and the screen is cleared for Host operations. The Green LED is controlled and is on
when uSign is in the capture mode; the red LED is host controlled.
The communication type can be RS232 or USB-HID. See the Communication Interface
section below that corresponds with the interface of your uSign unit. A Technical
Reference manual for the native uSign protocol is available from the factory.
Copyright © 2012, International Technologies & Systems Corp. All rights reserved.
Page 8 of 10
uSign 300 User Manual
5.1 RS232 Communication Interface
The uSign has a communication cable with a DB25 (100 Model) or DB-9 (200 Model)
connector that fits the computer serial (RS232) COM port connection. See the
Specifications, Interface Section for COM port settings.
Connect the RS232 connector to the PC and insure it is fully seated into the connector.
Connect the power adaptor output to the power input socket on the back of the DB
connector shell. Connect the power adaptor to the AC line power outlet.
5.2 USB Communication Interface
The USB interface is a HID Class. The USB communication uses the Windows OS
installed HID driver. uSign receives power form the Host USB connection.
Connect the USB connector to the PC and insure it is fully seated into the jack. If the
LEDs do not light, check the connections and the availability of power from the Host.
6.0 Specifications
6.1 Power requirement
Voltage 5VDC
Current 150mA typical
RS232 Power AC adapter, center positive adaptor plug output
USB Power Host USB port
6.2 Physical housing uSign 300
Overall size 129mm wide (5.1 in)
146mm length (5.75 in)
40mm thick including back plate (1.57 in)
Display 3.5-inch diagonal signature area
6.3 LCD screen & Resistive touch pad
Touchpad Resistive, transparent, pressure-sensitive screen
Sampling Rate Up to 118 samples per second
Touchpad Resolution Up to 1024 dpi
Display Resolution LCD Resolution: 320 x 240 dots
Copyright © 2012, International Technologies & Systems Corp. All rights reserved.
Page 9 of 10
uSign 300 User Manual
6.4 Communication interface
RS232
Baud rates 1200 to 115200
Default 9600 baud, data bits – 8, Parity – none, Stop bit – 1
USB 2.0 Full Speed (HID)
6.5 LED
Two individual LEDs (green & red)
Signature Pad or Host controlled
6.6 Agency Approvals
FCC Class B, & CE,
The product is RoHS compliant.
6.7 Electronics MTBF
Electronics MTBF 200,000 POH, based on Bellcore standard.
6.8 Electro-Static Discharges (ESD)
The electronics survive ESD of 4kV contact, and 8kV air discharge. Meets or exceeds
IEC 1000-4-2.
6.9 Environmental
Temperature ranges
Operating 1 to 45 C (34 to 113 F)
Storage (sealed container) -10 to 70 C (14 to 158 F)
Relative humidity
10% to 95% non-condensing
Copyright © 2012, International Technologies & Systems Corp. All rights reserved.
Page 10 of 10
uSign 300 User Manual
7.0 Outline Drawing
Figure 1 Outline Drawing for uSign 300
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

ID TECH uSign 300 Manuel utilisateur

Catégorie
Moniteurs à écran tactile
Taper
Manuel utilisateur

dans d''autres langues