LG 66722 Le manuel du propriétaire

Marque: LG

Modèle: 66722

Catégorie: Congélateurs

Taper: Le manuel du propriétaire

Ce manuel convient également à

66723

Sears Canada, Inc., 222 Jarvis Street, Toronto, Ontario, Canada M5B 2B8

Models / Modèles

www.sears.ca

BOTTOM FREEZER REFRIGERATOR

Use & Care Guide

MFL62017804

Printed in Mexico

CONGÉLATEUR INFÉRIEUR RÉFRIGÉRATEUR

Guide d'Utilisation et d'Entretien

ENGLISH FRANÇAIS

501-66722, 501-66723

TABLE OF CONTENTS

English Version 2

Warranty 3

Safety Instructions

Grounding Require ments 6

Parts and Features 7

Refrigerator Installation

Unpacking Your Refrigerator 8

Installation

Base Grille

Removing, R e v e r s i ng and Replacing

Your Refrigerator Doors

Leveling and Door Alignment

Using Your Refrigerator

Ensuring Proper Air Circulation

Multi Flow

Setting the Controls

Adjusting Control Settings

Food Storage Guide

Storing Frozen Food

Refrigerator Shelves

Snack Pan

Crisper Humidity Control

Crisper Cover with Lattice on inner Surface

Ice Bin

Durabase

Door Racks

Durabase Divider

Outside 22

Inside Walls 22

Door Liner and Gaskets 22

Plastic Parts 22

Condenser Coils 22

Light Bulb Replacement 22-23

Power Interruptions 23

When you go on vacation 23

About the Automatic Icemaker 24

Connecting the Water Line 25-27

Troubleshooting Guide

Customer Service Back Cover

Modular Door Bins

28-31

9-14

15-21

Egg Box

8-14

Dairy Corner

Crisper with Tilt-out feature

Glide-Out Drawer Basket

Care and Cleaning

22-23

General Cleaning Tips

One Year Limited Warranty

When installed, operated and maintained according to all instructions supplied with the product, if this appliance fails due

to a defect in material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME to arrange for

free repair.

If this appliance is used for other than private family purposes, this warranty applies for only 90 days from the date of

purchase.

Five Year Limited Warranty on Sealed Refrigeration System

For five years from the date of purchase, when this refrigerator is installed, operated, and maintained according to the

instructions supplied with it, Sears will repair the sealed system (consisting of refrigerant, connecting tubing, and

compressor), free of charge, if defective in material or workmanship.

This Warranty covers only defects in material and workmanship. Sears will NOT pay for:

1. Expendable items that can wear out from normal use, including but not limited to filters, belts, light bulbs, and bags.

2. A service technician to instruct the user in correct product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed, operated or maintained according to all instructions supplied

5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended

6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than

7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

Disclaimer of implied warranties; limitation of remedies

Customer's sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied

warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the

shortest period allowed by law. Sears shall not be liable for incidental or consequential damages.

purpose.

with the product.

those recommended in all instructions supplied with the product.

This warranty applies only while this appliance is used in the United States and Canada.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears Canada, Inc., Toronto, Ontario, Canada M5B 2B8

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitations

on the duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to

you.

BOTTOM FREEZER REFRIGERATOR

Kenmore Elite Appliance Warranty

WARRANTY

Kenmore Elite Limited Warranty

When installed, operated and maintained according to all instructions supplied with the product, if any non-consumable

part of this appliance other than the sealed refrigerant system fails due to a defect in material and workmanship within

one year from the date of purchase, call 1-800-4-MY-HOME® to arrange for free repair. This coverage applies for only 90

days from the date of purchase if this appliance is ever used for other than private family purposes.

If the sealed refrigerant system is defective within five years from the purchase date, call 1-800-4-MY-HOME® to arrange

for free repair. This coverage applies for only one year from the date of purchase if this appliance is ever used for other

than private family purposes.

This warranty covers only defects in material and workmanship. Sears will NOT pay for:

1. Expendable items that can wear out from normal use, including but not limited to filters, belts, light bulbs, and bags.

2. A service technician to instruct the user in correct product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed, operated or maintained according to the all instructions

supplied with the product.

5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those

recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

Disclaimer of implied warranties; limitation of remedies

Customer's sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied

warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the

shortest period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and

provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitation on the duration of

implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.

This warranty applies only while this appliance is used in the United States or Canada.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8

In the space below, record the date of purchase, model and serial number of your product. You will find the model and

serial number printed on an identification label located on the right-hand side of the refrigerator compartment. Have

these items of information available whenever you contact Sears concerning your product.

Model No.

Date of Purchase

Serial No. Dealer

Save these instructions and attach your sales receipt for future reference.

PRODUCT RECORD

PROTECTION AGREEMENTS

Master Protection Agreements

Congratulations on making a smart purchase. Your new

Kenmore product is designed and manufactured for years

of dependable operation. But like all products, it may

require preventive maintenance or repair from time to time.

That's when having a Master Protection Agreement can

save you money and aggravation.

’

Expert service by a force of more than 10,000

authorized Sears service technicians, which means

Unlimited service calls and nationwide service, as

often as you want us, whenever you want us.

"No-lemon” guarantee - replacement of your covered

product if four or more product failures occur within

Product replacement if your covered product can’t be

Annual Preventive Maintenance Check at your

Request - no extra charge.

Fast help by phone - we call it Rapid Resolution -

phone support from a Sears representative on all

products. Think of us as a ”talking owner’s manual.”

Power surge protection against electrical damage due

to power fluctuations.

Rental reimbursement if repair of your covered product



Parts and labor needed to help keep products operating

properly under normal use, not just defects. Our

coverage goes well beyond the product warranty. No

deductibles, no functional failure excluded from



someone you can trust will be working on your product.



$250 Food Loss Protection annually for any food

spoilage that is the result of mechanical failure of any

Covered refrigerator or freezer.



takes longer than promised.



10% discount off the regular price of any non-covered

repair service and related installed parts.



The Master Protection Agreement also helps extend the life

of your new product. Here’s what the Agreement* includes:

coverage - real protection.

twelve months.

Fixed.

additional information in the U.S.A. call 1-800-827-6655.

details call Sears Canada at 1-800-361-6655.

Sears Installation Service

For Sears professional installation of home appliances,

garage door openers, water heaters, and other major

home items, in the U.S.A. or Canada call

1-800-4-MY-HOME .

*Coverage in Canada varies on some items. For full

Some limitations and exclusions apply. For prices and

Once you purchase the Agreement, a simple phone call is

all that it takes for you to schedule service. You can call

anytime day or night, or schedule a service appointment

online.

The Master Protection Agreement is a risk free purchase.

If you cancel for any reason during the product warranty

period, we will provide a full refund. Or, a prorated refund

anytime after the product warranty period expires.

Purchase your Master Protection Agreement today!

This guide contains many important safety messages. Always read and obey all safety messages.

This is the safety alert symbol. It alerts you to safety messages that inform you

of hazards that can kill or hurt you or others, or cause damage to the product.

All safety messages will be preceded by the safety alert symbol and the hazard

signal word DANGER, WARNING, or CAUTION. These words mean:

WARNING

CAUTION

You can be killed or seriously injured if you don’t follow instructions.

Indicates an imminently hazardous situation which, if not avoided,

may result in minor or moderate injury, or product damage only.

All safety messages will identify the hazard, tell you how to reduce the chance of injury and tell you what can happen if

the instructions are not followed.

SAFETY MESSAGES

WARNING

To reduce the risk of fire, electric shock, or injury

to persons when using your product, basic safety

precautions should be followed, including the following:

Read all instructions before using this appliance:

NEVER unplug your refrigerator by pulling on the power cord.

Always grip the plug firmly and pull it straight out from the

outlet.

Repair or replace immediately all electric service cords that

have become frayed or otherwise damaged. Do not use a cord

that shows cracks or abrasion damage along its length or at

either the plug or connector end.

When moving your refrigerator away from the wall,

be careful not to roll over or damage the power cord.

DO NOT store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

DO NOT allow children to climb, stand, or hang on the

refrigerator doors or shelves in the refrigerator. They could

damage the refrigerator and seriously injure themselves.

Keep fingers out of “pinch point” areas; clearances between

Unplug your refrigerator before cleaning or making any repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

Before replacing a burned-out light bulb, unplug the

refrigerator or turn off power at the circuit breaker or fuse box

in order to avoid contact with a live wire filament. (A burned-

out light bulb may break when being replaced.)

NOTE: Setting

either or both controls to the OFF position does not remove

power to the light circuit.

After your refrigerator is in operation, do not touch the cold

surfaces in the freezer compartment when hands are damp or

wet. Skin may adhere to the extremely cold surfaces.

In refrigerators with automatic icemakers, avoid contact with

the moving parts of the ejector mechanism, or with the heating

element that releases the cubes. DO NOT place fingers or

hands on the automatic icemaking mechanism while the

refrigerator is plugged in.

DO NOT refreeze frozen foods which have thawed completely.

The United States Department of Agriculture in Home and

Garden Bulletin No. 69 says:

“...You may safely refreeze frozen foods that have thawed if

they still contain ice crystals or if they are still cold below

40 °F (4 °C).”

“...Thawed ground meats, poultry, or fish that have any off-odor

or off-color should not be refrozen and should not be eaten.

Thawed ice cream should be discarded. If the odor or color of

any food is poor or questionable, get rid of it. The food may be

dangerous to eat.”

“Even partial thawing and refreezing reduces the eating quality

of foods, particularly fruits, vegetables and prepared foods.

The eating quality of red meats is affected less than that of

many other foods. Use refrozen foods as soon as possible to

save as much of their quality as you can.”

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

the doors and cabinet are necessarily small. Be careful

when you open the doors when children are in the area.

For personal safety, this appliance must be properly grounded.

Have the wall outlet and the circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

The refrigerator-freezer should be so positioned that the supply

plug is accessible for quick disconnection when accident happens.

Do not store bottles in the freezer compartment - they may

break when frozen, causing damage.

This refrigerator must be properly installed in accordance

with the Attention Installer Instructions that were taped

to the front of the refrigerator.

DANGER

You will be killed or seriously injured if you don’t follow instructions.

IMPORTANT:

Please read carefully.

TO CONNECT ELECTRICITY

RECOMMENDED GROUNDING METHOD

The refrigerator should always be plugged into its own

individual properly grounded electrical outlet rated for

115 Volts, 60 Hz, AC only, and fused at 15 or 20 amperes.

This provides the best performance and also prevents

overloading house wiring circuits which could cause a fire

hazard from overheated wires. It is recommended that a

separate circuit serving only this appliance be provided.

Use a receptacle which cannot be turned off with a switch

or pull chain. Do not use an extension cord.

Where a standard two-prong wall outlet is encountered,

it is your personal responsibility and obligation to have it

replaced with a properly grounded three-prong wall outlet.

Do not, under any circumstances, cut or remove the

third (ground) prong from the power cord.

NOTE: Before performing any type of installation,

cleaning, or removing a light bulb, turn the control

(Thermostat, Refrigerator Control or Freezer Control,

depending on the model) to OFF and then disconnect the

refrigerator from the electrical source. When you are

finished, reconnect the refrigerator to the electrical source

and reset the control (Thermostat, Refrigerator Control or

Freezer Control, depending on the model) to the desired

setting.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain

conditions, we strongly recommend against the use of

an extension cord. However, if you still elect to use

an extension cord, it is absolutely necessary that it be

a UL-listed (in the United States), 3-wire grounding type

appliance extension cord having a grounding type plug

and outlet, and that the electrical rating of the cord be 15

amperes (minimum) and 120 volts.

Use of an extension cord will increase the clearance

needed for the back of the refrigerator.

WARNING

Electrical Shock Hazard

FOR PERSONAL SAFETY, this appliance must be

properly grounded. Have the wall outlet and the

circuit checked by a qualified electrician to make sure

the outlet is properly grounded.

Ensure proper

ground exists

before use.

3-prong

grounding

plug

3-prong

grounding type

wall receptacle

Your old refrigerator may have a cooling system that used If you are throwing away your old refrigerator, make sure

CFCs (chlorofluorocarbons). CFCs are believed to harm the CFC refrigerant is removed for proper disposal by a

stratospheric ozone. qualified servicer. If you intentionally release this CFC

refrigerant, you can be subject to fines and imprisonment

under provisions of environmental legislation.

DANGER: RISK OF CHILD ENTRAPMENT

BEFORE YOU THROW AWAY

YOUR OLD REFRIGERATOR

OR FREEZER

Take off the doors.

Leave the shelves in place so that

children may not easily climb inside.

CFC DISPOSAL

GROUNDING REQUIREMENTS

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous... even if they will sit for “just a few days”. If

you are getting rid of your old refrigerator, please follow

the instructions at right to help prevent accidents.

This appliance contains fluid (refrigerant, lubricant), is

made of parts and materials which are reusable and / or

recyclable. All the important materials should be sent to

the collecton center of waste material and can be reused

after rework (recycling).

For take back, please contact with the local agency.

CAUTION

This appliance is not intended for use by persons (including children) with reduce physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the

appliance by person responsible for their safety.

Children should be supervised to ensure that they do not play with the

appliance.

Ice Bin

Durabase

Divider

Refrigerator Door Rack

Wine Rack*

*On some models

Egg Box*

Glide-Out Drawer Basket

Freezer Light

Modular Door Bins

Dairy Corner

Use this section to become more familiar with the parts and features.

NOTE: This guide covers several different models. The refrigerator you have purchased may have some

or all of the items listed below. The locations of the features shown below may not match your model.

PARTS AND FEATURES

Cool Sense Electronic Temperature

Control System

Snack Pan

Refrigerator Light

Refrigerator Shelves

Supra Fresh Crisper with Tilt-Out Compartment*

Adjusta Cube Ice Maker*

Ice Tray *

REFRIGERATOR INSTALLATION

UNPACKING YOUR REFRIGERATOR

Do not use sharp instruments, rubbing alcohol, flammable

fluids or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see the Important Safety Instructions

section.

Refrigerator shelves are installed in the shipping position.

Please reinstall shelves according to your individual

storage needs.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the

refrigerator for cleaning or service, be sure to protect

the floor. Always pull the refrigerator straight out when

moving it. Do not wiggle or walk the refrigerator when

trying to move it, as floor damage could occur.

INSTALLATION

1. Avoid placing the unit near heat sources, direct sunlight,

or moisture.

2. To avoid vibration, the unit must be level. If required,

adjust the leveling screws to compensate for

unevenness of the floor. The front should be slightly

higher than the rear to aid in door closing. Leveling

screws can be turned easily by tipping the cabinet

slightly. Turn the leveling screws clockwise ( ) to

raise the unit, counterclockwise ( ) to lower it.

3. Install this appliance in an area where the temperature

is between 55 °F (13 °C) and 110 °F (43 °C.) If the

temperature around the appliance is too low or high,

cooling ability may be adversely affected.

1. Clean your refrigerator thoroughly and wipe off all dust

accumulated during shipping.

2. Install accessories such as ice cube bin, drawers,

shelves, etc., in their proper places. They are packed

together to prevent possible damage during shipment.

3. Let your refrigerator run for 2 or 3 hours before putting

food in it. Check the flow of cold air in the freezer

compartment to ensure proper cooling. Your refrigerator

is now ready for use.

WARNING:

Be careful when you work with hinge, base grille,

stopper, etc. you may be injured.

Do not put hands or metal sticks into air vents, base

grille, or bottom of refrigerator. You may be injured or

receive an electrical shock.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

WARNING

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion or fire.

CAUTION: Avoid placing the unit near heat sources,

direct sunlight or moisture.

Explosion Hazard

A proper distance from adjacent items

Please keep the refrigerator at a proper distance from

other things. Too small a distance from adjacent items

may result in lowered freezing capability and increased

electricity charge consumption.

To remove any remaining tape or glue, rub the area

briskly with your thumb. Tape or glue residue can also be

easily removed by rubbing a small amount of liquid dish

soap over the adhesive with your fingers. Wipe with warm

water and dry.

Remove tape and any temporary labels from your

refrigerator before usign. Do not remove any warningtype

labels, the model and serial number label, or the techsheet

(on some models), that is attached to back wall of the

refrigerator.

2”

(5.08 cm)

BASE GRILLE INSTALLATION

To remove the base grille

To install or replace Base Grille:

1. Remove the 2 screws from the bottom front part of

refrigerator.

2. Place Base Grille into position and insert and tighten

screws.

1. Open the doors. (Refrigerator and Freezer)

2. Once doors are open, remove screws from Base Grille

and remove.

3. Reattach screws to the base of refrigerator.

2.Removing Refrigerator Handle

NOTE: To assist in installing the handle on the right

side, place a small piece of masking tape near the

top of the handle before removing.

Grasp the handle tightly with both hands and slide the

handle up (1)(this may require some force).

The keyhole slots (2) on the back of the handle allow

the handle to separate from the mounting screws (3).

Use an adjustable wrench to remove the handle

mounting screws (3).

HOW TO REMOVE DOOR HANDLES

REFRIGERATOR INSTALLATION

IMPORTANT: Before you begin, turn the refrigerator OFF and unplug it. Remove food and any

adjustable door or utility bins from doors.

HOW TO REVERSE DOOR OPENING DIRECTION

(when converting from the left-opening type to right-

opening type)

1. Removing Refrigerator Door

Lift the Refrigerator door (3) slightly and remove it.

Loosen the 2 screws (9) and the 2 screws (10), and

lift off the middle hinge (11).

Use a flat tip screwdriver to pry off bottom hole cover

(7) and attach it on the right.

•

REMOVING,REVERSING AND REPLACING

REFRIGERATOR DOORS (For Drawer Type Models)

T O O L S Y O U M A Y N E E D

Hex head socket wrench

No. 2 Phillips screwdriver

Flat head screwdriver

Allen wrench

10 mm

1/4 in

3/8 in

1/4 in

3/32 in

Other Important and necessary tools are:

1/4 inch socket wrench 10mm open-end wrench

Adjustable wrench Flat 2-inch putty knife

•

Gently pry off the Top Hinge Cover with a flat head screwdriver

and remove (1).

Using 10 mm socket wrench, remove the 3 bolts and lift off the

Top Hinge. Set parts aside (2).

Pry off the cover (4) using a slotted screwdriver to find the

hole screw and attach it on the right.

Loosen the screws (5), remove the stopper (6) and

attach them on the left (on the opposite side).

Using a ¼-inch socket wrench, loosen and remove

Hinge Pin (8) from the Middle Hinge Pin Bracket.

door slightly and remove it.

NOTE: At this point the door will be loose, lift up

REFRIGERATOR INSTALLATION

3. Installing Refrigerator Door

Install the middle hinge (1) on the opposite side with the

screws (2), and the screw (3).

Install the door (4) so that it fits onto the middle hinge

pin (5).

Install the top hinge (6) with screws.

Reinstall top hinge cover (7).

4. After Completing the Job

Make sure that each at the four corners of the door

gasket is not folded over on itself. To ensure a good

seal, apply a small amount of silicon grease on the

gasket.

Corner

REFRIGERATOR INSTALLATION

Remove a layer of adhesive and backing to expose

new adhesive.

Install the plug buttons (4) on left side, rotating these

Install the handle mounting screw (3) on the right side

Hold the handle so the masking tape is at the bottom.

Align keyhole slots (2) on the top and bottom of the

back of the handle with the screws (3) mounted on

the front of the door.

Press the handle against the door front, making sure

that the screws (3) go into the keyhole slots (2).

Grasping the handle with both hands, press it firmly

against the front of the door and slide the handle

down (6). This may require some force.

Carefully loosen the plug buttons with your fingers(4).

The buttons can be unscrewed with your fingers,

rotating the pieces counter clockwise, and then

the piece will be loose and fall. The buttons were

installed without some pressure, for this reason the

action can be done with your forefinger or thumb

finger or with both.

pieces at clockwise with your fore and thumb fingers.

REFRIGERATOR INSTALLATION

HOW TO REMOVE DOOR HANDLES

NOTE: Handle appearance may vary from illustrations on this page.

2.. Removing Refrigerator Handle

•

Loosen the set screws (1) with the 3/32” Allen

Loosen the handle mounting fasteners (3)

wrench and remove the handle (2).

with the 1/4” Allen wrench.

Allen Wrench

Set Screw

Mounting

Fasteners

REMOVING,REVERSING AND REPLACING

REFRIGERATOR DOORS (For Swing Type Models)

T O O L S Y O U M A Y N E E D

Hex head socket wrench

No. 2 Phillips screwdriver

10 mm

1/4 in

3/8 in

1/4 in

3/32 in

IMPORTANT: Before you begin, turn the refrigerator OFF

and unplug it. Remove food and any adjustable door or

HOW TO REVERSE DOOR OPENING DIRECTION

(when converting from the left-opening type to right-

opening type)

Other Important and necessary tools are:

1/4 inch socket wrench 10mm open-end wrench

Adjustable wrench Flat 2-inch putty knife

•

1. Removing Refrigerator Door

Lift the Refrigerator door (3) slightly and remove it.

Pry off the cover (4) using a slotted screwdriver to find the

hole screw and attach it on the right.

Loosen the screws (5), remove the stopper (6) and

attach them on the left (on the opposite side).

Pry off the cover (9) using a slotted screwdriver and attach it on the right.

2. Removing Freezer Door

Lift the door (10) slightly and remove it.

Loosen the 2 screws (11), the 2 screws (12), and lift off the middle hinge (13).

Remove

the base grille (14).

Loosen the 2 screws (16), remove the bottom hinge

(17), and attach on the left.

Loosen the 2 screws (18) and attach the stopper (19)

on the left side of the base.

Gently pry off the Top Hinge Cover with a flat head screwdriver

Using 10 mm socket wrench, remove the 3 bolts and lift off the

•

and remove (1).

Top Hinge. Set parts aside (2).

Using a ¼-inch socket wrench, loosen and remove

Hinge Pin (7) from the Middle Hinge Pin Bracket.

and remove it.

NOTE: At this point the door will be loose, lift up door slightly

Before, remove totally the refrigerator door.

Loosen the 2 screws (9) and the 2 screws (10), and lift off the

middle hinge (11).

•

Flat head screwdriver

Allen wrench

3. Replacing Refrigerator Handle

•

Place the handle (2) on the door by adjusting handle

Turn handle upside down (5)

footprints to fit mounting fastners and tighten the set

screws (1) with the 3/32 ” Allen wrench.

REFRIGERATOR INSTALLATION

4. Installing Refrigerator Door

Install the middle hinge (1) on the opposite side with the

screws (2), and the screw (3).

Install the door (4) so that it fits onto the middle hinge

pin (5).

Install the top hinge (6) with screws.

Reinstall top hinge cover (7).

•

Install the plug buttons (4) on the left side.

Install the handle mounting fasteners (3)

on the right side.

Carefully loosen the plug buttons with your fingers(4).

The buttons can be unscrewed with your fingers,

rotating the pieces counter clockwise, and then

the piece will be loose and fall. The buttons were

installed without some pressure, for this reason the

action can be done with your forefinger or thumb

finger or with both.

CAUTION: When you remove the drawer, do not hold

handle. If it comes off, it could cause personal injury.

CAUTION: When laying down the drawer, be careful

not to damage the floor or hurt your feet by the sharp

edges on hinge side.

HOW TO REMOVE AND INSTALL THE

PULL OUT DRAWER

IMPORTANT: To avoid possible injury, product or property

damage, you will need two people to perform the following

instructions.

1. Removing Pull out Drawer

• Pull the drawer open to full lower extension. Remove the

lower basket (1) by lifting basket from rail system.

• Press both hangers with yours thumbs to lift it up.

• Separate the left and right rail cover

• Remove the screws(2) of the rail on both sides.

• With both hands, hold both sides of the door and pull it

up to separate it from the rails.

• With both hands, hold the center of the bar and push it

in to let both rails fitted simultaneously.

REFRIGERATOR INSTALLATION

HOW TO REMOVE AND INSTALL THE

PULL OUT DRAWER

IMPORTANT: To avoid possible injur or product or property

damage, you will need two people to perform the following

instructions.

2. Installing Pull out Drawer

• With both hands, hold the center of the bar and pull it

out to let both rails out to full extension simultaneously.

• Hook door supports (1) into rail tabes (2) .

• Lower door into final position and tighten the screws (3)

• Make sure you have a right rail cover for each side.

• Align the top holes of the rail cover with the top holes of

the door supports to assemble the rail cover.

• With the drawer pulled out to full extension, insert the

lower basket (4) in the rail assembly.

WARNING: To prevent accidental child and pet

entrapment or suffocation risk. DO NOT allow them to

play inside of drawer.

WARNING: DO NOT step or sit down on Freezer Door.

Right

Rail cover

Left

Rail cover

Verify the hole’s assembly

LEVELING AND DOOR ALIGNMENT

Door Closing

Your refrigerator has two front leveling screws one on

the right and one on the left. if your refrigerator seems

unsteady or you want the doors to close easier, adjust the

refrigerator’s tilt using the instructions below:

1. Plug refrigerator power cord into a 3-prong grounded

outlet. Move the refrigerator into its final position.

2. Use a screwdriver to adjust the leveling screws. Turn

the leveling screw clockwise to raise that side of the

refrigerator or counterclockwise to lower it. It may take

several turns of the leveling screw to adjust the tilt of

the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws.

This makes it easier to adjust the screws.

3. Open both doors again and check to make sure that

they close easily. If not, tilt the refrigerator slightly more

to the rear by turning both leveling screws clockwise. It

may take several more turns, and you should turn both

leveling screws the same amount.

4. Re-adjust if necessary.

5. Replace the base grille.

Door Alignment

If the space between your doors is uneven, follow the

instructions below to align the doors:

1. Pry off the top hinge cover.

2. Loosen the top hinge screws using a 5/16 in socket

or wrench.

3. Have someone hold the door in place with space

between doors even, or put a spacer between doors to

keep space even, while you tighten the top hinge

screws.

4. Replace the top hinge cover.

ENSURING PROPER AIR CIRCULATION

In order to ensure proper temperatures, air must flow

between the refrigerator and freezer sections. As shown

in the illustration below, air enters at top of the freezer and

circulates down. From bottom of the freezer, air is forced up

to top of refrigerator. Air enters refrigerator through top

vent, then circulates and exists at bottom, where it returns

to freezer.

MULTI-FLOW

Multi-Flow means powerful and effective cooling

operation. This is especially noticeable when new food

is placed in the refrigerator compartment.

If water or foreign substances enter the cool air vent

while cleaning, efficiency will be lowered. In addition, if

gasket is damaged, efficiency may be lowered because

of escaping cool air.

Do not block any of cool air vents with food packages.

If the vents are blocked, airflow will be interrupted and

temperature and moisture problems may occur.

IMPORTANT: Because air circulates between both

sections, any odors formed in one section will transfer to

the other. You must thoroughly clean both sections to

eliminate odors. To prevent odor transfer and drying out of

food, wrap or cover foods tightly. (See the Food Storage

Guide section for details.)

USING YOUR REFRIGERATOR

DOOR ALARM

With this feature you´ll listen a alarm when the freezer or

refrigerator door is not closed within 1 minute after it is

opened. These tones repeat every 30 seconds.

The alarm is cancelled when the freezer or the

refrigerator is closed correctly.

SETTING THE CONTROLS

Your refrigerator has two controls that let you regulate

the temperature in the freezer and refrigerator

compartments.

Initially set the REFRIGERATOR CONTROL at 37 °F

(3°

C) and the FREEZER CONTROL at 0 ° F ( -18 °C).

Leave it at this setting for 24 hours (one day) to

stabilize. Then adjust the compartment temperature

as desired.

Refrigerator control: Position 1 to 7

32 °F to 47

°F / 0 °C to 8 °C)

The higher the number setting, the colder the refrigerator

compartment will become.

Freezer control: Position 1 to 7

(-6 °F to 8

°F / - 21 °C to - 13 °C)

When the setting is at a higher number, the freezer

compartment becomes colder.

ULTRAICE

Press the ULTRAICE and the LED will turn

on. This function will remain activated for 24 hours and

intensify the cooling speed of freezer and increase the

amount office.

ADJUSTING CONTROL SETTINGS

Give the refrigerator time to cool down completely before

adding food. It is best to wait 24 hours before you put

food into the refrigerator. The mid-settings indicated in the

previous section should be correct for normal household

refrigerator usage. The controls are set correctly when

milk or juice is as cold as you like and when ice cream

is firm.

The refrigerator control functions as the thermostat for the

entire appliance (refrigerator and freezer sections.) The

higher the number setting, the longer the compressor will

run to keep the temperature colder. The freezer control

adjusts the cold air flow from the freezer to the

refrigerator. Setting the freezer control to a lower

temperature keeps more cold air in the Freezer

compartment to make it colder.

If you need to adjust temperatures in the refrigerator or

freezer, start by adjusting the refrigerator first. Wait 24

hours after the refrigerator adjustment to check the

freezer temperature. If it is too warm or too cold, then

adjust the freezer control as well.

Use the settings listed in the chart below as a guide.

Always remember to wait at least 24 hours between

adjustments.

RECOMMENDED

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR section Turn

too warm REFRIGERATOR

Door opened often

control to next

Large amount of food added

higher number,

Room temperature very warm wait 24 hours,

Then re-check

FREEZER section too warm/ Turn FREEZER

ice not made fast enough control to next

Door opened often

higher number,

Large amount of food added

wait 24 hours,

Very cold room temperature Then re-check

(can’t cycle often enough)

Heavy ice usage

Air vents blocked by items Move items out of

Airstream

REFRIGERATOR section too Turn

Cold REFRIGERATOR

Controls not set correctly for

Control to next

your conditions lower number,

wait 24 hours,

then re-check

FREEZER section too cold Turn FREEZER

Controls not set correctly for

control to next

your conditions lower number,

wait 24 hours,

then re-check

FOOD STORAGE GUIDE

Storing Fresh Food

Wrap or store food in the refrigerator in airtight and

moisture-proof material unless otherwise noted. This

prevents food odor and taste transfer throughout the

refrigerator. For dated products, check date code to

ensure freshness.

Butter or margarine

Keep opened butter in a covered dish or closed

compartment. When storing an extra supply, wrap

in freezer packaging and freeze.

Cheese

Store in the original wrapping until you are ready to

use it. Once opened, rewrap tightly in plastic wrap or

aluminum foil.

Milk

Wipe milk cartons. For best storage, place milk on interior

shelf, not on door shelf.

Eggs

Store in original carton on interior shelf, not on door shelf.

Fruit

Wash, let dry, and store in refrigerator in plastic bags or in

the crisper. Do not wash or hull berries until you are ready

to use them. Sort and keep berries in their original

container in a crisper, or store in a loosely closed paper

bag on a refrigerator shelf.

Leafy vegetables

Remove store wrapping and trim or tear off bruised and

discolored areas. Wash in cold water and drain. Place in a

plastic bag or plastic container and store in the crisper.

Vegetables with skins (carrots, peppers)

Place in plastic bags or plastic container and store

in crisper.

Fish

Snack pan

Store most chef fresh in original wrapping as long as it is

airtight and moisture-proof. Rewrap if necessary.

Leftovers

Cover leftovers with plastic wrap or aluminum foil. Plastic

containers with tight lids can also be used.

STORING FROZEN FOOD

NOTE: For further information about preparing food for

freezing or food storage times, check a freezer guide or a

reliable cookbook.

Packaging

Successful freezing depends on correct packaging. When

you close and seal the package, it must not allow air or

moisture in or out. If you do, you could have food odor

and taste transfer throughout the refrigerator and also dry

out frozen food.

Packaging recommendations:

Rigid plastic containers with tight-fitting lids

Straight-sided canning/freezing jars

Heavy-duty aluminum foil

Plastic-coated paper

Non-permeable plastic wraps

Specified freezer-grade self-sealing plastic bags

Follow package or container instructions for proper

freezing methods.

Do not use:

Bread wrappers

Non-polyethylene plastic containers

Containers without tight lids

Wax paper or wax-coated freezer wrap

Thin, semi-permeable wrap

Freezing

Your freezer will not quick-freeze any large quantity of

food. Do not put more unfrozen food into the freezer than

will freeze within 24 hours (no more than 2 to 3 lbs of food

per cubic foot of freezer space). Leave enough space in

the freezer for air to circulate around packages. Be careful

to leave enough room at the front so the door can close

tightly.

Storage times will vary according to the quality and type

of food, the type of packaging or wrap used (airtight and

moisture-proof) and the storage temperature. Ice crystals

inside a sealed package are normal. This simply means

that moisture in the food and air inside the package have

condensed, creating ice crystals.

NOTE: Allow hot foods to cool at room temperature for

30 minutes, then package and freeze. Cooling hot foods

before freezing saves energy.

NOTE: Do not store food near the sensor; it may cause

the sensor to malfunction.

USING YOUR REFRIGERATOR

WARNING

Suffocation Hazard

When using dry ice, provide adequate ventilation.

Dry ice is frozen carbon dioxide

(CO )

. When it

vaporizes, it can displace oxygen, causing dizziness,

light-headedness, unconsciousness and death by

suffocation. Open a window and do not breathe

the vapors.

Use fresh fish and shellfish the same day purchased.

IMPORTANT: Do not store bottles in the freezer

compartment - they may break when frozen,

causing damage.

USING YOUR REFRIGERATOR

REFRIGERATOR SECTION

REFRIGERATOR SHELVES

The shelves in your refrigerator are adjustable to meet

your individual storage needs. Your model may have

glass or wire shelves.

Storing similar food items together in your refrigerator and

adjusting the shelves to fit different heights of items will

make finding the exact item you want easier; it will also

reduce the amount of time the refrigerator door is open,

saving energy.

IMPORTANT: Do not clean glass shelves with warm

water when they are cold. Shelves may break if exposed

to sudden temperature changes or impact, such as

bumping. For your protection, glass shelves are made

with tempered glass, which will shatter into small pebble-

sized pieces.

NOTE: Glass shelves are heavy. Use special care when

removing them to avoid dropping them.

Adjusting Shelves

Remove shelves from the shipping position and replace

shelves in the position you want.

To remove a shelf Tilt up the front of the shelf in the

direction of (1) and lift it in the direction of (2). Pull the

shelf out.

To replace a shelf Tilt the front of the shelf up and

guide the shelf hooks into the slots at a desired height.

Then lower the front of the shelf so that the hooks drop

into the slots.

NOTE: Make sure that shelves are level from one side to

the other. Failure to do so may result in the shelf falling or

spilling food.

Sliding Out Shelves

You can slide some glass shelves in and out of your

refrigerator as follows.

To slide the shelf out, carefully pull front of shelf

toward you.

To slide shelf in, push shelf in until it stops.

To remove a sliding shelf from its metal frame:

1. Pull the shelf out to the stop position.

2. Tilt the front of the shelf up and pull it past the stop

3. Lift up the shelf to remove.

Replace the shelf by reversing the above steps.

Convenience Shelves (optional on some models)

Folding Shelf: You can store taller items such as gallon

containers or bottles by simply sliding the shelf back.

position.

DAIRY CORNER

1. To remove the dairy Bin, simply lift it and pull straight

out.

2. To replace the dairy Bin, slide it in above the desired

location and push down until it stops.

USING YOUR REFRIGERATOR

SNACK PAN

While holding the meat tray with one hand, pull it forward

slightly. Lift slightly and pull it out.

SUPRAFRESH CRISPERS WITH TILT - OUT

COMPARTMENT

Crispers with Tilt-Out Compartment

The crispers provide fresher-tasting fruit and vegetables

by letting you easily control humidity inside the drawer.

The crispers include:

1. A crisper drawer humidity control switch.

2. A lattice on the underside of the cover to efficiently hold

or release moisture.

3. A tilt-out compartment on the front of the crisper drawer.

CRISPER HUMIDITY CONTROL

You can control the amount of humidity in the moisture-

sealed crispers. Adjust the control to any setting between

and .

lets moist air out of the crisper for best storage of

fruits.

keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

CRISPER WITH TILT - OUT FEATURE

Tilt-Out Compartment

The tilt-out compartment on the front of the crisper is for

items stored best in low humidity such as apples and

oranges. The front of the compartment is transparent to

allow you to see compartment contents. Push the button

on the front of the compartment to open it.

To remove tilt-out compartment:

1. Pull crisper drawer out to the stop.

2. Open the compartment.

3. Grasp side of drawer and pull outward to release tab at

compartment base. Pull compartment toward you to

remove.

4. To replace compartment, insert compartment base tab

into one side of drawer. Pull slightly outward on

opposite side of drawer to insert other base tab.

Removing Crisper

To remove crisper drawer:

1. Slide drawer straight out to the stop.

2. Lift the front of the drawer, then pull it out to remove.

3. Replace the drawer by sliding it back in fully past the

drawer stop.

EGG BOX

Store Egg Box on interior shelf, not on door shelf.

CAUTION: Do not use the egg box as an ice storage

bin in the freezer compartment. The egg box can easily

easily break if it freezes.

(on some models)

USING YOUR REFRIGERATOR

CRISPER COVER WITH LATTICE ON INNER

SURFACE

To remove cover frame:

1. Remove both crisper drawers.

2. Remove glass cover from frame. Set safely aside for

rest of crisper removal procedure.

3. While holding crisper cover frame support, pull the

frame up and out.

WARNING: Be careful when handling glass cover since

glass is not attached to cover.

To remove lattice:

1. Be sure glass cover is removed.

2. Turn the cover frame over. Each lattice has its own

frame within the cover frame.

3. Pull left and right sides of lattice frame outward to

release lattice tabs from frame. Remove lattice.

To replace lattice:

1. Pull sides of each lattice frame outward to re-insert

tabs of lattice into frame.

2. Slide the cover frame back into refrigerator and

securely onto frame support.

3. Place the glass cover back onto top of cover frame.

DOOR RACKS

The door racks may be removed for easier cleaning.

Snap-on Door Racks

To remove the racks:

1. Remove all items in the door racks.

2. Push the rack against the inside wall of the door (A)

and lift up the door rack (B).

To replace the racks:

Hold either end of the door rack against the inside wall of the door.

2. Push down the rack until it locks in place.

MODULAR DOOR BINS

1. Bins can be moved to either side of the door.

T o remove the bin, simply lift the bin up and pull straight out.

3. To replace the bin, slide it in above the desired

support button and push down until it snaps into place.

4. When moving bins, make sure that bins are correctly

inserted so that they don

't fall out of door.

WARNING: Somebody can be hurt if door bins are not

firmly assembled.

NOTE: Do not adjust a bin that is loaded with food.

CAUTION: DO NOT allow children to play with baskets.

The pointed area of basket could injure them.

(Correct)

(Incorrect)

(on some models)

La page charge ...

LG 66722 Le manuel du propriétaire

Marque: LG

Modèle: 66722

Catégorie: Congélateurs

Taper: Le manuel du propriétaire

Ce manuel convient également à

66723

Télécharger le PDF

rapport

dans d''autres langues

English: LG 66722 Owner's manual

LG 66722 Le manuel du propriétaire

Ce manuel convient également à

LG 66722 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents